The adt7420 is software compatible to the adt7410.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the TI / Burr-Brown INA209 voltage / current / power
monitor.
Cc: Paul Hays <haysp@magma.net>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Assume that IT8771E and IT8772E are fully compatible with IT8728F.
IT8771E support contributed by Kelly Anderson.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Add support for MAX6581, MAX6602, MAX6622, MAX6636, MAX6689, MAX6693,
MAX6694, MAX6697, MAX6698, and MAX6699 temperature sensors
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
This is the HWMON patch for DA9055 PMIC and has got dependency on the
DA9055 MFD core.
This patch monitors the DA9055 PMIC's ADC channels vddout, junction temperature
and auxiliary channels.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: Dropped __devinit, __devexit, __devexit_p]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
So far, we use the NM10 Express Chipset PCI chip ID to detect TjMax for
Atom CPUs with model 0x1c. As it turns out, we can use the CPU stepping
(x86_mask) for the same purpose; stepping is 10 for all model 0x1c CPUs
with TjMax of 100 degrees C. This was verified by checking the output of
/proc/cpuinfo for the respective CPUs (D4xx, D5xx, N4xx, N5xx).
Other CPUs currently covered by the same code (Exx, Z6xx, Z2460) are not
supported by the NM10 Express Chipset. Most of those CPUs have TjMax of 90
degrees C, except for E6xxT models which have a TjMax of 110 degrees C.
E6xxT CPUs can however not be detected by software.
Calculate TjMax for Atom CPUs as follows. Note that the listed values are not
correct in some cases (230, 330). tjmax_table is used for those to override
the default values.
ID Stepping TjMax Models
0x1c 10 100 D4xx, N4xx, D5xx, N5xx
0x1c not 10 90 Z5xx, N2xx, 230, 330, others
0x26 - 90 Atom Tunnel Creek (Exx),
Lincroft (Z6xx)
0x27 - 90 Atom Medfield (Z2460)
0x36 - 100 Atom Cedar Trail (N2xxx, D2xxx)
Also drop the module dependency on PCI.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Signed-off-by: Guillaume Roguez <guillaume.roguez@savoirfairelinux.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon framework driver for Versatile Express sensors, providing
information about board level voltage (only when regulator driver
is not configured), currents, temperature and power/energy usage.
Labels for the values can be defined as DT properties.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Conflicts:
drivers/staging/omap-thermal/omap-thermal-common.
OMAP supplied dummy TC1 and TC2,
at the same time that the thermal tree removed them
from thermal_zone_device_register()
drivers/thermal/cpu_cooling.c b/drivers/thermal/cpu_cooling.c
propogate the upstream MAX_IDR_LEVEL re-name
to prevent a build failure
Previously-fixed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>
This movement is needed because the hwmon entries and corresponding sysfs
interface is a duplicate of utilities already provided by
driver/thermal/thermal_sys.c. The goal is to place it in thermal folder
and add necessary functions to use the in-kernel thermal interfaces.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This Patch adds support for mcp3221 chip to the
mcp3021 driver.
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CONFIG_EXPERIMENTAL is expected to be removed, so drop dependencies on it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add missing reference to IT8782F and IT8783E/F to it87 driver description
in Kconfig. Replace wrong reference to Si960 with the correct Si950.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
INA220 is register compatible to INA219, and INA230 is register compatible to
INA226, so all we need to do is to add name aliases for those two chips.
Cc: Lothar Felten <l-felten@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
MAX1110 is similar to MAX1111, with 8 instead of 4 channels. MAX1112 and MAX1113
are similar to MAX1110 and MAX1111, with 4.096V reference voltage instead of
2.048V.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add support for LM74 and LM71 to LM70 driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX197 is an A/D converter, made by Maxim. This driver currently
supports the MAX197, and MAX199. They are both 8-Channel, Multi-Range,
5V, 12-Bit DAS with 8+4 Bus Interface and Fault Protection.
The available ranges for the MAX197 are {0,-5V} to 5V, and {0,-10V} to
10V, while they are {0,-2V} to 2V, and {0,-4V} to 4V on the MAX199.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch brings basic support for the Analog Devices ADT7410 temperature
sensor. The following functionality has been implemented:
* get current temperature
* get/set minimum, maximum and critical temperature
* get/set hysteresis
* get alarm events for minimum, maximum and critical temperature
All implemented sysfs attributes have been sucessfully tested at temperatures
of 15°C to 40°C.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is a new driver for the Honeywell Humidicon HIH-6130/HIH-6131 humidity sensor.
The driver is based on the existing Sensiron sht21 driver with the necessary changes
to the probe, update_measurements and conversion functions necessary to use the
Honeywell sensors.
There's no difference between the 6130 & 6131 other than the 6131 having an external
condensation filter attached.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The DA9052 PMIC provides an Analogue to Digital Converter with 10 bits
resolution and 10 channels.
This patch monitors the DA9052 PMIC's ADC channels mostly for battery
parameters like battery temperature, junction temperature, battery
current etc.
This patch is functionally tested on Samsung SMDKV6410
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: __init --> __devinit for probe function]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since the watchdog code in sch56xx-common now uses the watchdog core, the
Kconfig entires for the sch5627 and sch5636 should depend on WATCHDOG
being set. Also select the watchdog core when we select one of the drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
New driver for INA219 and INA226, added support for IT8782F and IT8783E/F to
it87 driver, plus cleanups in a couple of drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ZX6H
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New driver for INA219 and INA226, added support for IT8782F and
IT8783E/F to it87 driver, plus cleanups in a couple of drivers."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (it87) Make temp3 attribute conditional for IT8782F
hwmon: (it87) Convert to use devm_kzalloc and devm_request_region
hwmon: INA219 and INA226 support
hwmon: (it87) Create voltage attributes only if voltage is enabled
hwmon: (ntc_thermistor) Fix checkpatch warning
hwmon: (ntc_thermistor) Optimize and fix build warning
hwmon: (ntc_thermistor) Return error code from hwmon_device_register
hwmon: (ntc_thermistor) Convert to devm_kzalloc
hwmon: (ad7314) Remove unused defines, and rename OFFSET to SHIFT
acpi_power_meter: clean up code around setup_attrs
acpi_power_meter: drop meter_rw_attrs, use common meter_attrs
acpi_power_meter: remove duplicate code between register_{ro,rw}_attrs
acpi_power_meter: use a {RW,RO}_SENSOR_TEMPLATE macro to clean things up
acpi_power_meter: use the same struct {rw,ro}_sensor_template for both
hwmon: use module_pci_driver
hwmon: (it87) Add support for IT8782F and IT8783E/F
Add support for the Texas Instruments INA219 and INA226 power monitors.
Signed-off-by: Lothar Felten <l-felten@ti.com>
[guenter.roeck@ericsson.com: formatting cleanup; check for smbus word data;
select PGA=8 for INA219]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The on-chip northbridge's temperature sensor of the upcoming
AMD Trinity CPUs works the same as for the previous CPUs.
Since it has a different PCI-ID, we just add the new one to the list
supported by k10temp.
This allows to use the k10temp driver on those CPUs.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
sht15 depends on GPIOLIB, not on GENERIC_GPIO.
This fixes the following build error, seen if GPIOLIB is not defined:
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_direction_input': => 293:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_direction_output': => 216:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_free': => 1000:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_get_value': => 296:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_request': => 946:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_set_value': => 218:2
src/drivers/hwmon/sht15.c: error: implicit declaration of function 'gpio_to_irq': => 514:2
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
gpio-fan depends on GPIOLIB, not on GENERIC_GPIO.
This fixes the following build error, seen if GPIOLIB is not defined:
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_direction_output': => 372:3
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_free': => 130:2
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_get_value': => 79:2
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_request': => 98:2
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_set_value': => 156:3
src/drivers/hwmon/gpio-fan.c: error: implicit declaration of function 'gpio_to_irq': => 114:2
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Simon Guinot <sguinot@lacie.com>
Add I2C driver for MCP3021 that is an ADC chip from Microchip.
The MCP3021 is a successive approximation A/D converter (ADC)
with 10-bit resolution.
The driver export the value of Vin to sysfs, the voltage unit is
mV. Through the sysfs interface, lm-sensors tool can also display
Vin voltage.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on a patch by David Jander that mostly did s/mc13783/mc13xxx/ .
Additionally use dev_get_drvdata instead of to_platform_device +
platform_get_drvdata in mc13783_adc_read (spotted by Jean Delvare).
Cc: David Jander <david.jander@protonic.nl>
Signed-off-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
GMT G781 is a ADM1032-compatible temperature sensor chip.
Add support to the LM90 driver.
Cc: Mike Gorchak <lestat@i.com.ua>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Manual fan speed control uses a standard interface and has received
sufficient testing and review by now, it can be enabled
unconditionally. This includes attributes pwm[1-8], pwm[1-8]_enable,
pwm[1-8]_mode and pwm[1-8]_freq.
We only let the user switch from automatic mode to manual mode, but
not the other way around, as automatic control settings may not have
been set properly by the BIOS.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for the watchdog integrated into the SMSC SCH5627 and
SCH5636 superio-s. Since the watchdog is part of the hwmon logical device
and thus shares ioports with it, the watchdog driver is integrated into the
existing hwmon drivers for these.
Note that this version of the watchdog support for sch56xx superio-s
implements the watchdog chardev interface itself, rather then relying on
the recently added watchdog core / watchdog_dev. This is done because
currently some needed functionality is missing from watchdog_dev, as soon
as this functionality is added (which is being discussed on the
linux-watchdog mailinglist), I'll convert this driver over to using
watchdog_dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[guenter.roeck@ericsson.com: Added missing linux/slab.h include]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add detection of the National Semiconductor (now Texas Instruments)
LM96080. It is functionally compatible with the LM80 but detection is
completely different.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
These are fully compatible with Jedec JC 42.4 as far as I can see.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Until we get a datasheet for the IT8728F, treat it as fully compatible
with the IT8721F, as it seems to work reasonably well.
This closes kernel bug #27262.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
LM96163 is an enhanced version of LM63 with improved PWM resolution. Add chip
detection code as well as support for improved PWM resolution if the chip is
configured to use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fintek F75387SG/RG is mostly compatible to F75373/F75375. Add support for it
to the F75375S driver.
Fan support for F75387SG/RG has been implemented but not tested.
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Bjoern Gerhart <oss@extracloud.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Rename dependency of EXYNOS4_TMU in Kconfig to the existing one.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This is essentially a stripped down version of the W83627DHG. Noticeable
difference is that it is still powered with +5V, as older models, even
though the ADC resolution is 8 mV as newer models have.
Thanks to Ulf Bruman (Saab Group) for doing all the testing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
A modprobe of hwmon drivers that read/write ISA addresses on a powerpc results
in a kernel Oops. These reads/writes are being done via the inb()/in_8() and
outb()/out_8() macros.
Prevent these drivers from being built for powerpc.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add datasheet reference and device ID for ADT75.
The ADT75, like some other LM75 derivatives, needs to be instantiated
using methods 1, 2, or 4.
For more information see Documentation/i2c/instantiating-devices.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Driver for AD7314, ADT7301, and ADT7302, ported from IIO.
Currently dropped power down mode support.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
[guenter.roeck@ericsson.com: Added MODULE_DEVICE_TABLE]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch allows to read temperature
from TMU(Thermal Management Unit) of SAMSUNG EXYNOS4 series of SoC.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
hwmon: (lm90) Refactor reading of config2 register
hwmon: (lm90) Make SA56004 detection more robust
hwmon: (lm90) Simplify handling of extended local temp register
hwmon: (pmbus) Add client driver for LM25066, LM5064, and LM5066
hwmon: (max34440) Add support for peak attributes
hwmon: (max8688) Add support for peak attributes
hwmon: (max16064) Add support for peak attributes
hwmon: (adm1275) Add support for peak attributes
hwmon: (pmbus) Add support for peak attributes
hwmon: Add new attributes to sysfs ABI
hwmon: (pmbus) Strengthen check for status register existence
hwmon: (pmbus) Add support for virtual pages
hwmon: (pmbus) Support reading and writing of word registers in device specific code
hwmon: (pmbus) Increase attribute name size
hwmon: (pmbus) Add ADP4000, NCP4200 and NCP4208 to list of supported devices
hwmon: (pmbus) Add support for VID output voltage mode
hwmon: (pmbus) Move PMBus drivers to drivers/hwmon/pmbus
hwmon: (coretemp) Add core/pkg threshold support to Coretemp
hwmon: (lm95241) Add support for LM95231
hwmon: LM95245 driver
...
Since the number of PMBus drivers is getting large, move them into
directory drivers/hwmon/pmbus to improve readability and scalability.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
LM95231 is fully compatible to LM95241; only necessary change is to add
chip detection.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
A hwmon driver for the National Semiconductor LM95245 dual temperature
sensors chip.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Lars-Peter Clausen