to #29722367
On some specific hardware with 128 bytes LLC cacheline, tk_core may
cause false sharing problem. We can align it to 128 bytes so that
it won't be affected by other global variables.
This change will make a bit waste on cache utilization but get good
number of performance improvement. So for both 64 and 128 bytes aligned
LLC cacheline, we adjust tk_core memory layout to avoid potential cacheline
contention.
Signed-off-by: Peng Wang <rocking@linux.alibaba.com>
Acked-by: Shanpei Chen <shanpeic@linux.alibaba.com>
Reviewed-by: Shile Zhang <shile.zhang@linux.alibaba.com>
Signed-off-by: caelli <caelli@tencent.com>
Reviewed-by: yilingjin <yilingjin@tencent.com>
Reviewed-by: yuehongwu <yuehongwu@tencent.com>
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
mainline inclusion
from mainline-v6.0-rc1
commit 70fb5ccf2e upstream.
--------------------------------
[Problem Statement]
select_idle_cpu() might spend too much time searching for an idle CPU,
when the system is overloaded.
The following histogram is the time spent in select_idle_cpu(),
when running 224 instances of netperf on a system with 112 CPUs
per LLC domain:
@usecs:
[0] 533 | |
[1] 5495 | |
[2, 4) 12008 | |
[4, 8) 239252 | |
[8, 16) 4041924 |@@@@@@@@@@@@@@ |
[16, 32) 12357398 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[32, 64) 14820255 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@|
[64, 128) 13047682 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[128, 256) 8235013 |@@@@@@@@@@@@@@@@@@@@@@@@@@@@ |
[256, 512) 4507667 |@@@@@@@@@@@@@@@ |
[512, 1K) 2600472 |@@@@@@@@@ |
[1K, 2K) 927912 |@@@ |
[2K, 4K) 218720 | |
[4K, 8K) 98161 | |
[8K, 16K) 37722 | |
[16K, 32K) 6715 | |
[32K, 64K) 477 | |
[64K, 128K) 7 | |
netperf latency usecs:
=======
case load Lat_99th std%
TCP_RR thread-224 257.39 ( 0.21)
The time spent in select_idle_cpu() is visible to netperf and might have a negative
impact.
[Symptom analysis]
The patch [1] from Mel Gorman has been applied to track the efficiency
of select_idle_sibling. Copy the indicators here:
SIS Search Efficiency(se_eff%):
A ratio expressed as a percentage of runqueues scanned versus
idle CPUs found. A 100% efficiency indicates that the target,
prev or recent CPU of a task was idle at wakeup. The lower the
efficiency, the more runqueues were scanned before an idle CPU
was found.
SIS Domain Search Efficiency(dom_eff%):
Similar, except only for the slower SIS
patch.
SIS Fast Success Rate(fast_rate%):
Percentage of SIS that used target, prev or
recent CPUs.
SIS Success rate(success_rate%):
Percentage of scans that found an idle CPU.
The test is based on Aubrey's schedtests tool, including netperf, hackbench,
schbench and tbench.
Test on vanilla kernel:
schedstat_parse.py -f netperf_vanilla.log
case load se_eff% dom_eff% fast_rate% success_rate%
TCP_RR 28 threads 99.978 18.535 99.995 100.000
TCP_RR 56 threads 99.397 5.671 99.964 100.000
TCP_RR 84 threads 21.721 6.818 73.632 100.000
TCP_RR 112 threads 12.500 5.533 59.000 100.000
TCP_RR 140 threads 8.524 4.535 49.020 100.000
TCP_RR 168 threads 6.438 3.945 40.309 99.999
TCP_RR 196 threads 5.397 3.718 32.320 99.982
TCP_RR 224 threads 4.874 3.661 25.775 99.767
UDP_RR 28 threads 99.988 17.704 99.997 100.000
UDP_RR 56 threads 99.528 5.977 99.970 100.000
UDP_RR 84 threads 24.219 6.992 76.479 100.000
UDP_RR 112 threads 13.907 5.706 62.538 100.000
UDP_RR 140 threads 9.408 4.699 52.519 100.000
UDP_RR 168 threads 7.095 4.077 44.352 100.000
UDP_RR 196 threads 5.757 3.775 35.764 99.991
UDP_RR 224 threads 5.124 3.704 28.748 99.860
schedstat_parse.py -f schbench_vanilla.log
(each group has 28 tasks)
case load se_eff% dom_eff% fast_rate% success_rate%
normal 1 mthread 99.152 6.400 99.941 100.000
normal 2 mthreads 97.844 4.003 99.908 100.000
normal 3 mthreads 96.395 2.118 99.917 99.998
normal 4 mthreads 55.288 1.451 98.615 99.804
normal 5 mthreads 7.004 1.870 45.597 61.036
normal 6 mthreads 3.354 1.346 20.777 34.230
normal 7 mthreads 2.183 1.028 11.257 21.055
normal 8 mthreads 1.653 0.825 7.849 15.549
schedstat_parse.py -f hackbench_vanilla.log
(each group has 28 tasks)
case load se_eff% dom_eff% fast_rate% success_rate%
process-pipe 1 group 99.991 7.692 99.999 100.000
process-pipe 2 groups 99.934 4.615 99.997 100.000
process-pipe 3 groups 99.597 3.198 99.987 100.000
process-pipe 4 groups 98.378 2.464 99.958 100.000
process-pipe 5 groups 27.474 3.653 89.811 99.800
process-pipe 6 groups 20.201 4.098 82.763 99.570
process-pipe 7 groups 16.423 4.156 77.398 99.316
process-pipe 8 groups 13.165 3.920 72.232 98.828
process-sockets 1 group 99.977 5.882 99.999 100.000
process-sockets 2 groups 99.927 5.505 99.996 100.000
process-sockets 3 groups 99.397 3.250 99.980 100.000
process-sockets 4 groups 79.680 4.258 98.864 99.998
process-sockets 5 groups 7.673 2.503 63.659 92.115
process-sockets 6 groups 4.642 1.584 58.946 88.048
process-sockets 7 groups 3.493 1.379 49.816 81.164
process-sockets 8 groups 3.015 1.407 40.845 75.500
threads-pipe 1 group 99.997 0.000 100.000 100.000
threads-pipe 2 groups 99.894 2.932 99.997 100.000
threads-pipe 3 groups 99.611 4.117 99.983 100.000
threads-pipe 4 groups 97.703 2.624 99.937 100.000
threads-pipe 5 groups 22.919 3.623 87.150 99.764
threads-pipe 6 groups 18.016 4.038 80.491 99.557
threads-pipe 7 groups 14.663 3.991 75.239 99.247
threads-pipe 8 groups 12.242 3.808 70.651 98.644
threads-sockets 1 group 99.990 6.667 99.999 100.000
threads-sockets 2 groups 99.940 5.114 99.997 100.000
threads-sockets 3 groups 99.469 4.115 99.977 100.000
threads-sockets 4 groups 87.528 4.038 99.400 100.000
threads-sockets 5 groups 6.942 2.398 59.244 88.337
threads-sockets 6 groups 4.359 1.954 49.448 87.860
threads-sockets 7 groups 2.845 1.345 41.198 77.102
threads-sockets 8 groups 2.871 1.404 38.512 74.312
schedstat_parse.py -f tbench_vanilla.log
case load se_eff% dom_eff% fast_rate% success_rate%
loopback 28 threads 99.976 18.369 99.995 100.000
loopback 56 threads 99.222 7.799 99.934 100.000
loopback 84 threads 19.723 6.819 70.215 100.000
loopback 112 threads 11.283 5.371 55.371 99.999
loopback 140 threads 0.000 0.000 0.000 0.000
loopback 168 threads 0.000 0.000 0.000 0.000
loopback 196 threads 0.000 0.000 0.000 0.000
loopback 224 threads 0.000 0.000 0.000 0.000
According to the test above, if the system becomes busy, the
SIS Search Efficiency(se_eff%) drops significantly. Although some
benchmarks would finally find an idle CPU(success_rate% = 100%), it is
doubtful whether it is worth it to search the whole LLC domain.
[Proposal]
It would be ideal to have a crystal ball to answer this question:
How many CPUs must a wakeup path walk down, before it can find an idle
CPU? Many potential metrics could be used to predict the number.
One candidate is the sum of util_avg in this LLC domain. The benefit
of choosing util_avg is that it is a metric of accumulated historic
activity, which seems to be smoother than instantaneous metrics
(such as rq->nr_running). Besides, choosing the sum of util_avg
would help predict the load of the LLC domain more precisely, because
SIS_PROP uses one CPU's idle time to estimate the total LLC domain idle
time.
In summary, the lower the util_avg is, the more select_idle_cpu()
should scan for idle CPU, and vice versa. When the sum of util_avg
in this LLC domain hits 85% or above, the scan stops. The reason to
choose 85% as the threshold is that this is the imbalance_pct(117)
when a LLC sched group is overloaded.
Introduce the quadratic function:
y = SCHED_CAPACITY_SCALE - p * x^2
and y'= y / SCHED_CAPACITY_SCALE
x is the ratio of sum_util compared to the CPU capacity:
x = sum_util / (llc_weight * SCHED_CAPACITY_SCALE)
y' is the ratio of CPUs to be scanned in the LLC domain,
and the number of CPUs to scan is calculated by:
nr_scan = llc_weight * y'
Choosing quadratic function is because:
[1] Compared to the linear function, it scans more aggressively when the
sum_util is low.
[2] Compared to the exponential function, it is easier to calculate.
[3] It seems that there is no accurate mapping between the sum of util_avg
and the number of CPUs to be scanned. Use heuristic scan for now.
For a platform with 112 CPUs per LLC, the number of CPUs to scan is:
sum_util% 0 5 15 25 35 45 55 65 75 85 86 ...
scan_nr 112 111 108 102 93 81 65 47 25 1 0 ...
For a platform with 16 CPUs per LLC, the number of CPUs to scan is:
sum_util% 0 5 15 25 35 45 55 65 75 85 86 ...
scan_nr 16 15 15 14 13 11 9 6 3 0 0 ...
Furthermore, to minimize the overhead of calculating the metrics in
select_idle_cpu(), borrow the statistics from periodic load balance.
As mentioned by Abel, on a platform with 112 CPUs per LLC, the
sum_util calculated by periodic load balance after 112 ms would
decay to about 0.5 * 0.5 * 0.5 * 0.7 = 8.75%, thus bringing a delay
in reflecting the latest utilization. But it is a trade-off.
Checking the util_avg in newidle load balance would be more frequent,
but it brings overhead - multiple CPUs write/read the per-LLC shared
variable and introduces cache contention. Tim also mentioned that,
it is allowed to be non-optimal in terms of scheduling for the
short-term variations, but if there is a long-term trend in the load
behavior, the scheduler can adjust for that.
When SIS_UTIL is enabled, the select_idle_cpu() uses the nr_scan
calculated by SIS_UTIL instead of the one from SIS_PROP. As Peter and
Mel suggested, SIS_UTIL should be enabled by default.
This patch is based on the util_avg, which is very sensitive to the
CPU frequency invariance. There is an issue that, when the max frequency
has been clamp, the util_avg would decay insanely fast when
the CPU is idle. Commit addca28512 ("cpufreq: intel_pstate: Handle no_turbo
in frequency invariance") could be used to mitigate this symptom, by adjusting
the arch_max_freq_ratio when turbo is disabled. But this issue is still
not thoroughly fixed, because the current code is unaware of the user-specified
max CPU frequency.
[Test result]
netperf and tbench were launched with 25% 50% 75% 100% 125% 150%
175% 200% of CPU number respectively. Hackbench and schbench were launched
by 1, 2 ,4, 8 groups. Each test lasts for 100 seconds and repeats 3 times.
The following is the benchmark result comparison between
baseline:vanilla v5.19-rc1 and compare:patched kernel. Positive compare%
indicates better performance.
Each netperf test is a:
netperf -4 -H 127.0.1 -t TCP/UDP_RR -c -C -l 100
netperf.throughput
=======
case load baseline(std%) compare%( std%)
TCP_RR 28 threads 1.00 ( 0.34) -0.16 ( 0.40)
TCP_RR 56 threads 1.00 ( 0.19) -0.02 ( 0.20)
TCP_RR 84 threads 1.00 ( 0.39) -0.47 ( 0.40)
TCP_RR 112 threads 1.00 ( 0.21) -0.66 ( 0.22)
TCP_RR 140 threads 1.00 ( 0.19) -0.69 ( 0.19)
TCP_RR 168 threads 1.00 ( 0.18) -0.48 ( 0.18)
TCP_RR 196 threads 1.00 ( 0.16) +194.70 ( 16.43)
TCP_RR 224 threads 1.00 ( 0.16) +197.30 ( 7.85)
UDP_RR 28 threads 1.00 ( 0.37) +0.35 ( 0.33)
UDP_RR 56 threads 1.00 ( 11.18) -0.32 ( 0.21)
UDP_RR 84 threads 1.00 ( 1.46) -0.98 ( 0.32)
UDP_RR 112 threads 1.00 ( 28.85) -2.48 ( 19.61)
UDP_RR 140 threads 1.00 ( 0.70) -0.71 ( 14.04)
UDP_RR 168 threads 1.00 ( 14.33) -0.26 ( 11.16)
UDP_RR 196 threads 1.00 ( 12.92) +186.92 ( 20.93)
UDP_RR 224 threads 1.00 ( 11.74) +196.79 ( 18.62)
Take the 224 threads as an example, the SIS search metrics changes are
illustrated below:
vanilla patched
4544492 +237.5% 15338634 sched_debug.cpu.sis_domain_search.avg
38539 +39686.8% 15333634 sched_debug.cpu.sis_failed.avg
128300000 -87.9% 15551326 sched_debug.cpu.sis_scanned.avg
5842896 +162.7% 15347978 sched_debug.cpu.sis_search.avg
There is -87.9% less CPU scans after patched, which indicates lower overhead.
Besides, with this patch applied, there is -13% less rq lock contention
in perf-profile.calltrace.cycles-pp._raw_spin_lock.raw_spin_rq_lock_nested
.try_to_wake_up.default_wake_function.woken_wake_function.
This might help explain the performance improvement - Because this patch allows
the waking task to remain on the previous CPU, rather than grabbing other CPUs'
lock.
Each hackbench test is a:
hackbench -g $job --process/threads --pipe/sockets -l 1000000 -s 100
hackbench.throughput
=========
case load baseline(std%) compare%( std%)
process-pipe 1 group 1.00 ( 1.29) +0.57 ( 0.47)
process-pipe 2 groups 1.00 ( 0.27) +0.77 ( 0.81)
process-pipe 4 groups 1.00 ( 0.26) +1.17 ( 0.02)
process-pipe 8 groups 1.00 ( 0.15) -4.79 ( 0.02)
process-sockets 1 group 1.00 ( 0.63) -0.92 ( 0.13)
process-sockets 2 groups 1.00 ( 0.03) -0.83 ( 0.14)
process-sockets 4 groups 1.00 ( 0.40) +5.20 ( 0.26)
process-sockets 8 groups 1.00 ( 0.04) +3.52 ( 0.03)
threads-pipe 1 group 1.00 ( 1.28) +0.07 ( 0.14)
threads-pipe 2 groups 1.00 ( 0.22) -0.49 ( 0.74)
threads-pipe 4 groups 1.00 ( 0.05) +1.88 ( 0.13)
threads-pipe 8 groups 1.00 ( 0.09) -4.90 ( 0.06)
threads-sockets 1 group 1.00 ( 0.25) -0.70 ( 0.53)
threads-sockets 2 groups 1.00 ( 0.10) -0.63 ( 0.26)
threads-sockets 4 groups 1.00 ( 0.19) +11.92 ( 0.24)
threads-sockets 8 groups 1.00 ( 0.08) +4.31 ( 0.11)
Each tbench test is a:
tbench -t 100 $job 127.0.0.1
tbench.throughput
======
case load baseline(std%) compare%( std%)
loopback 28 threads 1.00 ( 0.06) -0.14 ( 0.09)
loopback 56 threads 1.00 ( 0.03) -0.04 ( 0.17)
loopback 84 threads 1.00 ( 0.05) +0.36 ( 0.13)
loopback 112 threads 1.00 ( 0.03) +0.51 ( 0.03)
loopback 140 threads 1.00 ( 0.02) -1.67 ( 0.19)
loopback 168 threads 1.00 ( 0.38) +1.27 ( 0.27)
loopback 196 threads 1.00 ( 0.11) +1.34 ( 0.17)
loopback 224 threads 1.00 ( 0.11) +1.67 ( 0.22)
Each schbench test is a:
schbench -m $job -t 28 -r 100 -s 30000 -c 30000
schbench.latency_90%_us
========
case load baseline(std%) compare%( std%)
normal 1 mthread 1.00 ( 31.22) -7.36 ( 20.25)*
normal 2 mthreads 1.00 ( 2.45) -0.48 ( 1.79)
normal 4 mthreads 1.00 ( 1.69) +0.45 ( 0.64)
normal 8 mthreads 1.00 ( 5.47) +9.81 ( 14.28)
*Consider the Standard Deviation, this -7.36% regression might not be valid.
Also, a OLTP workload with a commercial RDBMS has been tested, and there
is no significant change.
There were concerns that unbalanced tasks among CPUs would cause problems.
For example, suppose the LLC domain is composed of 8 CPUs, and 7 tasks are
bound to CPU0~CPU6, while CPU7 is idle:
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7
util_avg 1024 1024 1024 1024 1024 1024 1024 0
Since the util_avg ratio is 87.5%( = 7/8 ), which is higher than 85%,
select_idle_cpu() will not scan, thus CPU7 is undetected during scan.
But according to Mel, it is unlikely the CPU7 will be idle all the time
because CPU7 could pull some tasks via CPU_NEWLY_IDLE.
lkp(kernel test robot) has reported a regression on stress-ng.sock on a
very busy system. According to the sched_debug statistics, it might be caused
by SIS_UTIL terminates the scan and chooses a previous CPU earlier, and this
might introduce more context switch, especially involuntary preemption, which
impacts a busy stress-ng. This regression has shown that, not all benchmarks
in every scenario benefit from idle CPU scan limit, and it needs further
investigation.
Besides, there is slight regression in hackbench's 16 groups case when the
LLC domain has 16 CPUs. Prateek mentioned that we should scan aggressively
in an LLC domain with 16 CPUs. Because the cost to search for an idle one
among 16 CPUs is negligible. The current patch aims to propose a generic
solution and only considers the util_avg. Something like the below could
be applied on top of the current patch to fulfill the requirement:
if (llc_weight <= 16)
nr_scan = nr_scan * 32 / llc_weight;
For LLC domain with 16 CPUs, the nr_scan will be expanded to 2 times large.
The smaller the CPU number this LLC domain has, the larger nr_scan will be
expanded. This needs further investigation.
There is also ongoing work[2] from Abel to filter out the busy CPUs during
wakeup, to further speed up the idle CPU scan. And it could be a following-up
optimization on top of this change.
Suggested-by: Tim Chen <tim.c.chen@intel.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Tested-by: Mohini Narkhede <mohini.narkhede@intel.com>
Tested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Link: https://lore.kernel.org/r/20220612163428.849378-1-yu.c.chen@intel.com
Signed-off-by: Xue Sinian <tangyuan911@yeah.net>
commit 6afb257d6dd71085344e1472ea6e820b5dc0a8e3 openeuler.
----------------------------------------------------------------------
Disable cluster scheduling by default since it's not a universal win.
User can choose to enable it through sysctl or at boot time according to
their scenario.
Signed-off-by: Xue Sinian <tangyuan911@yeah.net>
commit 8ce3e706b31409147f035c037055caa68e450ce5 openeuler.
Reference: https://lore.kernel.org/lkml/cover.1638563225.git.tim.c.chen@linux.intel.com/
----------------------------------------------------------------------
Allow run time configuration of the scheduler to use cluster
scheduling. Configuration can be changed via the sysctl variable
/proc/sys/kernel/sched_cluster. Setting it to 1 enable cluster
scheduling and setting it to 0 turns it off.
Cluster scheduling should benefit independent tasks by load balancing
them between clusters. It reaps the most benefit when the system's CPUs
are not fully busy, so we can spread the tasks out between the clusters to
reduce contention on cluster resource (e.g. L2 cache).
However, if the system is expected to operate close to full utilization,
the system admin could turn this feature off so as not to incur
extra load balancing overhead between the cluster domains.
Signed-off-by: Xue Sinian <tangyuan911@yeah.net>
commit 211b6fb7d5a8558a453475a08a697e651ca2d0cb openeuler.
Reference: https://lore.kernel.org/lkml/cover.1638563225.git.tim.c.chen@linux.intel.com/
----------------------------------------------------------------------
A system admin may not want to use cluster scheduling. Make changes to
allow cluster topology level to be skipped when building sched domains.
Create SDTL_SKIP bit on the sched_domain_topology_level flag so we can
check if the cluster topology level should be skipped when building
sched domains.
Signed-off-by: Xue Sinian <tangyuan911@yeah.net>
Reference: https://lore.kernel.org/lkml/20220915073423.25535-1-yangyicong@huawei.com/
commit 0c3a4f986962ed94da6e26ba3ec0bdf700945894 openeuler.
----------------------------------------------------------------------
For platforms having clusters like Kunpeng920, CPUs within the same cluster
have lower latency when synchronizing and accessing shared resources like
cache. Thus, this patch tries to find an idle cpu within the cluster of the
target CPU before scanning the whole LLC to gain lower latency.
Testing has been done on Kunpeng920 by pinning tasks to one numa and two
numa. On Kunpeng920, Each numa has 8 clusters and each cluster has 4 CPUs.
With this patch, We noticed enhancement on tbench within one numa or cross
two numa.
On numa 0:
6.0-rc1 patched
Hmean 1 351.20 ( 0.00%) 396.45 * 12.88%*
Hmean 2 700.43 ( 0.00%) 793.76 * 13.32%*
Hmean 4 1404.42 ( 0.00%) 1583.62 * 12.76%*
Hmean 8 2833.31 ( 0.00%) 3147.85 * 11.10%*
Hmean 16 5501.90 ( 0.00%) 6089.89 * 10.69%*
Hmean 32 10428.59 ( 0.00%) 10619.63 * 1.83%*
Hmean 64 8223.39 ( 0.00%) 8306.93 * 1.02%*
Hmean 128 7042.88 ( 0.00%) 7068.03 * 0.36%*
On numa 0-1:
6.0-rc1 patched
Hmean 1 363.06 ( 0.00%) 397.13 * 9.38%*
Hmean 2 721.68 ( 0.00%) 789.84 * 9.44%*
Hmean 4 1435.15 ( 0.00%) 1566.01 * 9.12%*
Hmean 8 2776.17 ( 0.00%) 3007.05 * 8.32%*
Hmean 16 5471.71 ( 0.00%) 6103.91 * 11.55%*
Hmean 32 10164.98 ( 0.00%) 11531.81 * 13.45%*
Hmean 64 17143.28 ( 0.00%) 20078.68 * 17.12%*
Hmean 128 14552.70 ( 0.00%) 15156.41 * 4.15%*
Hmean 256 12827.37 ( 0.00%) 13326.86 * 3.89%*
Note neither Kunpeng920 nor x86 Jacobsville supports SMT, so the SMT branch
in the code has not been tested but it supposed to work.
Signed-off-by: Xue Sinian <tangyuan911@yeah.net>
Reference: https://lore.kernel.org/lkml/20220915073423.25535-1-yangyicong@huawei.com/
commit 53ad6bf76d9c646e3c8494ed82d90f304c50de1f openeuler.
----------------------------------------------------------------------
Add per-cpu cluster domain info and cpus_share_lowest_cache() API.
This is the preparation for the optimization of select_idle_cpu()
on platforms with cluster scheduler level.
Signed-off-by: Xue Sinian <tangyuan911@yeah.net>
commit cfe7ddcbd7 upstream.
------------------------------------------------------------------------
This flag was introduced in 2014 by commit:
d77b3ed5c9 ("sched: Add a new SD_SHARE_POWERDOMAIN for sched_domain")
but AFAIA it was never leveraged by the scheduler. The closest thing I can
think of is EAS caring about frequency domains, and it does that by
leveraging performance domains.
Remove the flag. No change in functionality is expected.
Suggested-by: Morten Rasmussen <morten.rasmussen@arm.com>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: https://lore.kernel.org/r/20200817113003.20802-2-valentin.schneider@arm.com
Signed-off-by: Xue Sinian <tangyuan911@yeah.net>
commit 36c5bdc438 upstream.
------------------------------------------------------------------------
That flag is set unconditionally in sd_init(), and no one checks for it
anymore. Remove it.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200415210512.805-5-valentin.schneider@arm.com
Signed-off-by: Xue Sinian <tangyuan911@yeah.net>
commit e669ac8ab9 upstream.
------------------------------------------------------------------------
The SD_LOAD_BALANCE flag is set unconditionally for all domains in
sd_init(). By making the sched_domain->flags syctl interface read-only, we
have removed the last piece of code that could clear that flag - as such,
it will now be always present. Rather than to keep carrying it along, we
can work towards getting rid of it entirely.
cpusets don't need it because they can make CPUs be attached to the NULL
domain (e.g. cpuset with sched_load_balance=0), or to a partitioned
root_domain, i.e. a sched_domain hierarchy that doesn't span the entire
system (e.g. root cpuset with sched_load_balance=0 and sibling cpusets with
sched_load_balance=1).
isolcpus apply the same "trick": isolated CPUs are explicitly taken out of
the sched_domain rebuild (using housekeeping_cpumask()), so they get the
NULL domain treatment as well.
Remove the checks against SD_LOAD_BALANCE.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200415210512.805-4-valentin.schneider@arm.com
Signed-off-by: Xue Sinian <tangyuan911@yeah.net>
commit 0252aa08aafb4a40ea2d821f58e88e99a644b097 openeuler.
When I compile the kernel with CONFIG_PPC_WATCHDOG is disabled on
PowerPC, I got the following compile error:
In file included from kernel/hung_task.c:11:0:
./include/linux/nmi.h: In function ‘touch_nmi_watchdog’:
./include/linux/nmi.h:143:2: error: implicit declaration of function ‘arch_touch_nmi_watchdog’; did you mean ‘touch_nmi_watchdog’? [-Werror=implicit-function-declaration]
arch_touch_nmi_watchdog();
^~~~~~~~~~~~~~~~~~~~~~~
touch_nmi_watchdog
It is because CONFIG_HARDLOCKUP_DETECTOR_PERF is still enabled in my
situation. Fix it by excluding arch_touch_nmi_watchdog() only when
CONFIG_PPC_WATCHDOG is disabled.
Signed-off-by: huwentao <huwentao19@h-partners.com>
commit bdda54cc39843589ee91a0176ca9a94adf307763 openeuler.
Functions called in sdei_handler are not allowed to be kprobed, so
marked them as NOKPROBE_SYMBOL. There are so many functions in
'watchdog_check_timestamp()'. Luckily, we don't need
'CONFIG_HARDLOCKUP_CHECK_TIMESTAMP' now. So just make
CONFIG_SDEI_WATCHDOG depends on !CONFIG_HARDLOCKUP_CHECK_TIMESTAMP
in case someone add 'CONFIG_HARDLOCKUP_CHECK_TIMESTAMP' in the future.
Signed-off-by: huwentao <huwentao19@h-partners.com>
commit 5bc048a102ef9c3748464cacce443a0f1d9bed5b openeuler.
The trigger period of secure time is set by firmware. We need to check
the time_stamp every time the secure time fires to make sure the
hardlockup detection is not executed too soon. We need to refresh
'last_timestamp' to the current time when we enable the nmi_watchdog.
Otherwise, false hardlockup may be detected when the secure timer fires
the first time.
Signed-off-by: huwentao <huwentao19@h-partners.com>
commit 4ffed7d5435d12be6762e6fdef92fd2c67fc27df openeuler.
In current code, the hardlockup detect code is contained by
CONFIG_HARDLOCKUP_DETECTOR_PERF. This patch makes this code public so
that other arch hardlockup detector can use it.
Signed-off-by: huwentao <huwentao19@h-partners.com>
We intend to archive kernle-debug rpm in yum. Release kernel will
build perf/tools/bpf-tools rpm, to avoid kernle-debug build the same
rpm, disable them.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Pull networking fixes from David Miller:
1) Validate tunnel options length in act_tunnel_key, from Xin Long.
2) Fix DMA sync bug in gve driver, from Adi Suresh.
3) TSO kills performance on some r8169 chips due to HW issues, disable
by default in that case, from Corinna Vinschen.
4) Fix clock disable mismatch in fec driver, from Chubong Yuan.
5) Fix interrupt status bits define in hns3 driver, from Huazhong Tan.
6) Fix workqueue deadlocks in qeth driver, from Julian Wiedmann.
7) Don't napi_disable() twice in r8152 driver, from Hayes Wang.
8) Fix SKB extension memory leak, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
r8152: avoid to call napi_disable twice
MAINTAINERS: Add myself as maintainer of virtio-vsock
udp: drop skb extensions before marking skb stateless
net: rtnetlink: prevent underflows in do_setvfinfo()
can: m_can_platform: remove unnecessary m_can_class_resume() call
can: m_can_platform: set net_device structure as driver data
hv_netvsc: Fix send_table offset in case of a host bug
hv_netvsc: Fix offset usage in netvsc_send_table()
net-ipv6: IPV6_TRANSPARENT - check NET_RAW prior to NET_ADMIN
sfc: Only cancel the PPS workqueue if it exists
nfc: port100: handle command failure cleanly
net-sysfs: fix netdev_queue_add_kobject() breakage
r8152: Re-order napi_disable in rtl8152_close
net: qca_spi: Move reset_count to struct qcaspi
net: qca_spi: fix receive buffer size check
net/ibmvnic: Ignore H_FUNCTION return from H_EOI to tolerate XIVE mode
Revert "net/ibmvnic: Fix EOI when running in XIVE mode"
net/mlxfw: Verify FSM error code translation doesn't exceed array size
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Fix auto group size calculation
...
Fix problems with switching cpufreq drivers on some x86 systems with
ACPI (and with changing the operation modes of the intel_pstate driver
on those systems) introduced by recent changes related to the
management of frequency limits in cpufreq.
-----BEGIN PGP SIGNATURE-----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=S23p
-----END PGP SIGNATURE-----
Merge tag 'pm-5.4-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management regression fix from Rafael Wysocki:
"Fix problems with switching cpufreq drivers on some x86 systems with
ACPI (and with changing the operation modes of the intel_pstate driver
on those systems) introduced by recent changes related to the
management of frequency limits in cpufreq"
* tag 'pm-5.4-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: QoS: Invalidate frequency QoS requests after removal
pidfd_poll() is defined as returning 'unsigned int' but the
.poll method is declared as returning '__poll_t', a bitwise type.
Fix this by using the proper return type and using the EPOLL
constants instead of the POLL ones, as required for __poll_t.
Fixes: b53b0b9d9a ("pidfd: add polling support")
Cc: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: stable@vger.kernel.org # 5.3
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191120003320.31138-1-luc.vanoostenryck@gmail.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Switching cpufreq drivers (or switching operation modes of the
intel_pstate driver from "active" to "passive" and vice versa)
does not work on some x86 systems with ACPI after commit
3000ce3c52 ("cpufreq: Use per-policy frequency QoS"), because
the ACPI _PPC and thermal code uses the same frequency QoS request
object for a given CPU every time a cpufreq driver is registered
and freq_qos_remove_request() does not invalidate the request after
removing it from its QoS list, so freq_qos_add_request() complains
and fails when that request is passed to it again.
Fix the issue by modifying freq_qos_remove_request() to clear the qos
and type fields of the frequency request pointed to by its argument
after removing it from its QoS list so as to invalidate it.
Fixes: 3000ce3c52 ("cpufreq: Use per-policy frequency QoS")
Reported-and-tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Daniel Borkmann says:
====================
pull-request: bpf 2019-11-15
The following pull-request contains BPF updates for your *net* tree.
We've added 1 non-merge commits during the last 9 day(s) which contain
a total of 1 file changed, 3 insertions(+), 1 deletion(-).
The main changes are:
1) Fix a missing unlock of bpf_devs_lock in bpf_offload_dev_create()'s
error path, from Dan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull perf fixes from Ingo Molnar:
"Misc fixes: a handful of AUX event handling related fixes, a Sparse
fix and two ABI fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix missing static inline on perf_cgroup_switch()
perf/core: Consistently fail fork on allocation failures
perf/aux: Disallow aux_output for kernel events
perf/core: Reattach a misplaced comment
perf/aux: Fix the aux_output group inheritance fix
perf/core: Disallow uncore-cgroup events
Pull misc vfs fixes from Al Viro:
"Assorted fixes all over the place; some of that is -stable fodder,
some regressions from the last window"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ecryptfs_lookup_interpose(): lower_dentry->d_parent is not stable either
ecryptfs_lookup_interpose(): lower_dentry->d_inode is not stable
ecryptfs: fix unlink and rmdir in face of underlying fs modifications
audit_get_nd(): don't unlock parent too early
exportfs_decode_fh(): negative pinned may become positive without the parent locked
cgroup: don't put ERR_PTR() into fc->root
autofs: fix a leak in autofs_expire_indirect()
aio: Fix io_pgetevents() struct __compat_aio_sigset layout
fs/namespace.c: fix use-after-free of mount in mnt_warn_timestamp_expiry()
uclamp_update_active() should perform the update when
p->uclamp[clamp_id].active is true. But when the logic was inverted in
[1], the if condition wasn't inverted correctly too.
[1] https://lore.kernel.org/lkml/20190902073836.GO2369@hirez.programming.kicks-ass.net/
Reported-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Patrick Bellasi <patrick.bellasi@matbug.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: babbe170e0 ("sched/uclamp: Update CPU's refcount on TG's clamp changes")
Link: https://lkml.kernel.org/r/20191114211052.15116-1-qais.yousef@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It looks like a "static inline" has been missed in front
of the empty definition of perf_cgroup_switch() under
certain configurations.
Fixes the following sparse warning:
kernel/events/core.c:1035:1: warning: symbol 'perf_cgroup_switch' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20191106132527.19977-1-ben.dooks@codethink.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit:
313ccb9615 ("perf: Allocate context task_ctx_data for child event")
makes the inherit path skip over the current event in case of task_ctx_data
allocation failure. This, however, is inconsistent with allocation failures
in perf_event_alloc(), which would abort the fork.
Correct this by returning an error code on task_ctx_data allocation
failure and failing the fork in that case.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20191105075702.60319-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit
ab43762ef0 ("perf: Allow normal events to output AUX data")
added 'aux_output' bit to the attribute structure, which relies on AUX
events and grouping, neither of which is supported for the kernel events.
This notwithstanding, attempts have been made to use it in the kernel
code, suggesting the necessity of an explicit hard -EINVAL.
Fix this by rejecting attributes with aux_output set for kernel events.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20191030134731.5437-3-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A comment is in a wrong place in perf_event_create_kernel_counter().
Fix that.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20191030134731.5437-2-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While discussing uncore event scheduling, I noticed we do not in fact
seem to dis-allow making uncore-cgroup events. Such events make no
sense what so ever because the cgroup is a CPU local state where
uncore counts across a number of CPUs.
Disallow them.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While seemingly harmless, __sched_fork() does hrtimer_init(), which,
when DEBUG_OBJETS, can end up doing allocations.
This then results in the following lock order:
rq->lock
zone->lock.rlock
batched_entropy_u64.lock
Which in turn causes deadlocks when we do wakeups while holding that
batched_entropy lock -- as the random code does.
Solve this by moving __sched_fork() out from under rq->lock. This is
safe because nothing there relies on rq->lock, as also evident from the
other __sched_fork() callsite.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qian Cai <cai@lca.pw>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: bigeasy@linutronix.de
Cc: cl@linux.com
Cc: keescook@chromium.org
Cc: penberg@kernel.org
Cc: rientjes@google.com
Cc: thgarnie@google.com
Cc: tytso@mit.edu
Cc: will@kernel.org
Fixes: b7d5dc2107 ("random: add a spinlock_t to struct batched_entropy")
Link: https://lkml.kernel.org/r/20191001091837.GK4536@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 TSX Async Abort and iTLB Multihit mitigations from Thomas Gleixner:
"The performance deterioration departement is not proud at all of
presenting the seventh installment of speculation mitigations and
hardware misfeature workarounds:
1) TSX Async Abort (TAA) - 'The Annoying Affair'
TAA is a hardware vulnerability that allows unprivileged
speculative access to data which is available in various CPU
internal buffers by using asynchronous aborts within an Intel TSX
transactional region.
The mitigation depends on a microcode update providing a new MSR
which allows to disable TSX in the CPU. CPUs which have no
microcode update can be mitigated by disabling TSX in the BIOS if
the BIOS provides a tunable.
Newer CPUs will have a bit set which indicates that the CPU is not
vulnerable, but the MSR to disable TSX will be available
nevertheless as it is an architected MSR. That means the kernel
provides the ability to disable TSX on the kernel command line,
which is useful as TSX is a truly useful mechanism to accelerate
side channel attacks of all sorts.
2) iITLB Multihit (NX) - 'No eXcuses'
iTLB Multihit is an erratum where some Intel processors may incur
a machine check error, possibly resulting in an unrecoverable CPU
lockup, when an instruction fetch hits multiple entries in the
instruction TLB. This can occur when the page size is changed
along with either the physical address or cache type. A malicious
guest running on a virtualized system can exploit this erratum to
perform a denial of service attack.
The workaround is that KVM marks huge pages in the extended page
tables as not executable (NX). If the guest attempts to execute in
such a page, the page is broken down into 4k pages which are
marked executable. The workaround comes with a mechanism to
recover these shattered huge pages over time.
Both issues come with full documentation in the hardware
vulnerabilities section of the Linux kernel user's and administrator's
guide.
Thanks to all patch authors and reviewers who had the extraordinary
priviledge to be exposed to this nuisance.
Special thanks to Borislav Petkov for polishing the final TAA patch
set and to Paolo Bonzini for shepherding the KVM iTLB workarounds and
providing also the backports to stable kernels for those!"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/taa: Fix printing of TAA_MSG_SMT on IBRS_ALL CPUs
Documentation: Add ITLB_MULTIHIT documentation
kvm: x86: mmu: Recovery of shattered NX large pages
kvm: Add helper function for creating VM worker threads
kvm: mmu: ITLB_MULTIHIT mitigation
cpu/speculation: Uninline and export CPU mitigations helpers
x86/cpu: Add Tremont to the cpu vulnerability whitelist
x86/bugs: Add ITLB_MULTIHIT bug infrastructure
x86/tsx: Add config options to set tsx=on|off|auto
x86/speculation/taa: Add documentation for TSX Async Abort
x86/tsx: Add "auto" option to the tsx= cmdline parameter
kvm/x86: Export MDS_NO=0 to guests when TSX is enabled
x86/speculation/taa: Add sysfs reporting for TSX Async Abort
x86/speculation/taa: Add mitigation for TSX Async Abort
x86/cpu: Add a "tsx=" cmdline option with TSX disabled by default
x86/cpu: Add a helper function x86_read_arch_cap_msr()
x86/msr: Add the IA32_TSX_CTRL MSR
A cast to 'time_t' was accidentally left in place during the
conversion of __do_adjtimex() to 64-bit timestamps, so the
resulting value is incorrectly truncated.
Remove the cast so the 64-bit time gets propagated correctly.
Fixes: ead25417f8 ("timex: use __kernel_timex internally")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20191108203435.112759-2-arnd@arndb.de
Pull cgroup fix from Tejun Heo:
"There's an inadvertent preemption point in ptrace_stop() which was
reliably triggering for a test scenario significantly slowing it down.
This contains Oleg's fix to remove the unwanted preemption point"
* 'for-5.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: freezer: call cgroup_enter_frozen() with preemption disabled in ptrace_stop()
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for timekeepoing and clocksource drivers:
- VDSO data was updated conditional on the availability of a VDSO
capable clocksource. This causes the VDSO functions which do not
depend on a VDSO capable clocksource to operate on stale data.
Always update unconditionally.
- Prevent a double free in the mediatek driver
- Use the proper helper in the sh_mtu2 driver so it won't attempt to
initialize non-existing interrupts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping/vsyscall: Update VDSO data unconditionally
clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name()
clocksource/drivers/mediatek: Fix error handling
Pull scheduler fixes from Thomas Gleixner:
"Two fixes for scheduler regressions:
- Plug a subtle race condition which was introduced with the rework
of the next task selection functionality. The change of task
properties became unprotected which can be observed inconsistently
causing state corruption.
- A trivial compile fix for CONFIG_CGROUPS=n"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix pick_next_task() vs 'change' pattern race
sched/core: Fix compilation error when cgroup not selected
Pull irq fixlet from Thomas Gleixner:
"A trivial fix for a kernel doc regression where an argument change was
not reflected in the documentation"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq/irqdomain: Update __irq_domain_alloc_fwnode() function documentation
Pull stacktrace fix from Thomas Gleixner:
"A small fix for a stacktrace regression.
Saving a stacktrace for a foreign task skipped an extra entry which
makes e.g. the output of /proc/$PID/stack incomplete"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stacktrace: Don't skip first entry on noncurrent tasks
if the child has been negative and just went positive
under us, we want coherent d_is_positive() and ->d_inode.
Don't unlock the parent until we'd done that work...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
the caller of ->get_tree() expects NULL left there on error...
Reported-by: Thibaut Sautereau <thibaut@sautereau.fr>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull networking fixes from David Miller:
1) BPF sample build fixes from Björn Töpel
2) Fix powerpc bpf tail call implementation, from Eric Dumazet.
3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.
4) Fix crash in ebtables when using dnat target, from Florian Westphal.
5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
Fainelli.
6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.
7) Various KCSAN fixes all over the networking, from Eric Dumazet.
8) Memory leaks in mlx5 driver, from Alex Vesker.
9) SMC interface refcounting fix, from Ursula Braun.
10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.
11) Add a TX lock to synchonize the kTLS TX path properly with crypto
operations. From Jakub Kicinski.
12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
Garzarella.
13) Infinite loop in Intel ice driver, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
ixgbe: need_wakeup flag might not be set for Tx
i40e: need_wakeup flag might not be set for Tx
igb/igc: use ktime accessors for skb->tstamp
i40e: Fix for ethtool -m issue on X722 NIC
iavf: initialize ITRN registers with correct values
ice: fix potential infinite loop because loop counter being too small
qede: fix NULL pointer deref in __qede_remove()
net: fix data-race in neigh_event_send()
vsock/virtio: fix sock refcnt holding during the shutdown
net: ethernet: octeon_mgmt: Account for second possible VLAN header
mac80211: fix station inactive_time shortly after boot
net/fq_impl: Switch to kvmalloc() for memory allocation
mac80211: fix ieee80211_txq_setup_flows() failure path
ipv4: Fix table id reference in fib_sync_down_addr
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
net: usb: qmi_wwan: add support for DW5821e with eSIM support
CDC-NCM: handle incomplete transfer of MTU
nfc: netlink: fix double device reference drop
NFC: st21nfca: fix double free
...
Commit 67692435c4 ("sched: Rework pick_next_task() slow-path")
inadvertly introduced a race because it changed a previously
unexplored dependency between dropping the rq->lock and
sched_class::put_prev_task().
The comments about dropping rq->lock, in for example
newidle_balance(), only mentions the task being current and ->on_cpu
being set. But when we look at the 'change' pattern (in for example
sched_setnuma()):
queued = task_on_rq_queued(p); /* p->on_rq == TASK_ON_RQ_QUEUED */
running = task_current(rq, p); /* rq->curr == p */
if (queued)
dequeue_task(...);
if (running)
put_prev_task(...);
/* change task properties */
if (queued)
enqueue_task(...);
if (running)
set_next_task(...);
It becomes obvious that if we do this after put_prev_task() has
already been called on @p, things go sideways. This is exactly what
the commit in question allows to happen when it does:
prev->sched_class->put_prev_task(rq, prev, rf);
if (!rq->nr_running)
newidle_balance(rq, rf);
The newidle_balance() call will drop rq->lock after we've called
put_prev_task() and that allows the above 'change' pattern to
interleave and mess up the state.
Furthermore, it turns out we lost the RT-pull when we put the last DL
task.
Fix both problems by extracting the balancing from put_prev_task() and
doing a multi-class balance() pass before put_prev_task().
Fixes: 67692435c4 ("sched: Rework pick_next_task() slow-path")
Reported-by: Quentin Perret <qperret@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Quentin Perret <qperret@google.com>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
When cgroup is disabled the following compilation error was hit
kernel/sched/core.c: In function ‘uclamp_update_active_tasks’:
kernel/sched/core.c:1081:23: error: storage size of ‘it’ isn’t known
struct css_task_iter it;
^~
kernel/sched/core.c:1084:2: error: implicit declaration of function ‘css_task_iter_start’; did you mean ‘__sg_page_iter_start’? [-Werror=implicit-function-declaration]
css_task_iter_start(css, 0, &it);
^~~~~~~~~~~~~~~~~~~
__sg_page_iter_start
kernel/sched/core.c:1085:14: error: implicit declaration of function ‘css_task_iter_next’; did you mean ‘__sg_page_iter_next’? [-Werror=implicit-function-declaration]
while ((p = css_task_iter_next(&it))) {
^~~~~~~~~~~~~~~~~~
__sg_page_iter_next
kernel/sched/core.c:1091:2: error: implicit declaration of function ‘css_task_iter_end’; did you mean ‘get_task_cred’? [-Werror=implicit-function-declaration]
css_task_iter_end(&it);
^~~~~~~~~~~~~~~~~
get_task_cred
kernel/sched/core.c:1081:23: warning: unused variable ‘it’ [-Wunused-variable]
struct css_task_iter it;
^~
cc1: some warnings being treated as errors
make[2]: *** [kernel/sched/core.o] Error 1
Fix by protetion uclamp_update_active_tasks() with
CONFIG_UCLAMP_TASK_GROUP
Fixes: babbe170e0 ("sched/uclamp: Update CPU's refcount on TG's clamp changes")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Patrick Bellasi <patrick.bellasi@matbug.net>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Ben Segall <bsegall@google.com>
Link: https://lkml.kernel.org/r/20191105112212.596-1-qais.yousef@arm.com
caelli