Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The General Register Files are an area of registers containing a lot
of single-bit settings for numerous components as well full components
like usbphy control. Therefore all used components are accessed
via the syscon provided by the grf nodes or from the sub-devices
created through the simple-mfd created from the grf node.
Some settings are not used by anything but will need to be set up
according to expectations on the kernel side.
Best example is the force_jtag setting, which defaults to on and
results in the soc switching the pin-outputs between jtag and sdmmc
automatically depending on the card-detect status. This conflicts
heavily with how the dw_mmc driver expects to do its work and also
with the clock-controller, which has most likely deactivated the
jtag clock due to it being unused.
So far the handling of this setting was living in the mach-rockchip
code for the arm32-based rk3288 but that of course doesn't work
for arm64 socs and would also look ugly for further arm32 socs.
Also always disabling this setting is quite specific to linux and
its subsystems, other operating systems might prefer other settings,
so that the bootloader cannot really set a sane default for all.
So introduce a top-level driver for the grf that handles these
settings that need to be a certain way but nobody cares about.
Other needed settings might surface in the future and can then
be added here, but only as a last option. Ideally general GRF
settings should be handled in the driver needing them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
By definition this directory contains drivers that are specific to the
Rockchip architecture. All Kconfig options should therefore depend on
ARCH_ROCKCHIP to avoid exposing these symbols on other architectures.
For example, this options currently shows up as new when doing an
incremental build on PowerPC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[add COMPILE_TEST alternative condition]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This driver is found on RK3288 SoCs.
In order to meet high performance and low power requirements, a power
management unit is designed or saving power when RK3288 in low power
mode.
The RK3288 PMU is dedicated for managing the power of the whole chip.
PMU can work in the Low Power Mode by setting bit[0] of PMU_PWRMODE_CON
register. After setting the register, PMU would enter the Low Power mode.
In the low power mode, pmu will auto power on/off the specified power
domain, send idle req to specified power domain, shut down/up pll and
so on. All of above are configurable by setting corresponding registers.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
[replace dsb() with dsb(sy) for arm64 buildability; sy is the default,
so no functional change; adapt to per-user clocks in genpd]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Jianping Liu