This adds support for the Texas Instruments ADS8344 ADC chip. This chip
has a 16-bit 8-Channel ADC and is access directly through SPI.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When building with CONFIG_GPIOLIB is not set
gcc warns this:
drivers/iio/adc/ti-ads7950.c:75:19: error: field chip has incomplete type
struct gpio_chip chip;
^~~~
drivers/iio/adc/ti-ads7950.c: In function ti_ads7950_set:
drivers/iio/adc/ti-ads7950.c:409:32: error: implicit declaration of function gpiochip_get_data; did you mean acpi_get_data? [-Werror=implicit-function-declaration]
struct ti_ads7950_state *st = gpiochip_get_data(chip);
^~~~~~~~~~~~~~~~~
acpi_get_data
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: c97dce792d ("iio: adc: ti-ads7950: add GPIO support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_platform_ioremap_resource() to be able to drop a bit of
explicit boilerplate code.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use a local "struct device *dev" in imx7d_adc_probe() for brevity. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7616 is a 12-bit ADC with 16 channels.
The AD7616 can be configured to work in hardware mode by controlling it via
gpio pins and read data via spi. No support for software mode yet, but it
is a work in progress.
This device requires a reset in order to update oversampling, so chip info
has got a new attribute to mark this.
The current assumption that this driver makes for AD7616, is that it's
working in Hardware Mode with Serial, Burst and Sequencer modes activated.
To activate them, following pins must be pulled high:
-SER/PAR
-SEQEN
And following must be pulled low:
-WR/BURST
-DB4/SEQEN
Datasheets:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7616.pdf
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Available oversampling ratios and scales can be shown by calling a
common ad7606_show_avail function which takes as parameters the array
which stores the values, together with the size of the array.
Oversampling options are now defined in chip info
structure and they are loaded at probe.
Has_Oversampling attribute was removed because oversampling_num was added
and it is not needed anymore.
The purpose of this patch is to deal with the scale_avail and
oversampling_avail arrays in a generic way. This makes it easier to add
support for new devices which will work with different scales and
oversampling ratios. It is also an intermediate step for adding support
for ad7616 which has different oversampling sampling ratios available.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Between "config" and "MAX9611" there is a tab, replace it
with a space.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When initializing the priv->data array starting from index 1, there is one
less element to consider than when initializing the full array.
Fixes: e717f8c6df ("iio: adc: Add the TI ads124s08 ADC code")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Checking if regulator is valid before reading
NPCM ADC regulator voltage to avoid system crash
in a case the regulator is not valid.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For devices from the SigmaDelta family we need to keep CS low when doing a
conversion, since the device will use the MISO line as a interrupt to
indicate that the conversion is complete.
This is why the driver locks the SPI bus and when the SPI bus is locked
keeps as long as a conversion is going on. The current implementation gets
one small detail wrong though. CS is only de-asserted after the SPI bus is
unlocked. This means it is possible for a different SPI device on the same
bus to send a message which would be wrongfully be addressed to the
SigmaDelta device as well. Make sure that the last SPI transfer that is
done while holding the SPI bus lock de-asserts the CS signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <Alexandru.Ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add PM and runtime PM support to STM32 DFSDM drivers:
- stm32-dfsdm-core: manage clocks.
- stm32-dfsdm-adc: restore channels configuration upon resume. Also stop
restart everything in case of buffer mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The sample frequency is driven using the oversampling ratio depending
on the SPI bus frequency.
Currently, oversampling ratio is computed by an entire division:
- spi_freq / sample_freq. This may result in inaccurate value.
Using DIV_ROUND_CLOSEST improves resulting sample frequency, which is
useful for audio that requests fixed rates (such as: 8, 16 or 32 kHz).
BTW, introduce new routine to re-factor sample frequency setting, and
move frequency accuracy message from warning to debug level.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Claim direct mode to ensure no buffer mode is in use for:
- single conversion
- sample rate setting (must be set when filter isn't enabled).
- oversampling ratio (must be set when filter isn't enabled).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
DFSDM conversions can be launched continuously, or using various
triggers:
- by software
- hardware triggers (e.g. like in stm32-adc: TIM, LPTIM, EXTI)
- synchronously with DFSDM filter 0. e.g. for filters 1, 2
Launching conversions can be done using two methods:
a - injected:
- scan mode can be used to convert several channels each time a
trigger occurs.
- When not is scan mode, channels are converted in sequence, one upon
each trigger.
b - regular:
- supports software triggers or synchronous with filter 0
- single or continuous conversions
This patch finalizes DFSDM operating modes using IIO buffer modes:
- INDIO_BUFFER_SOFTWARE: regular continuous conversions (no trigger)
but limited to 1 channel. Users must set sampling frequency in this case.
For filters > 1, conversions can be started synchronously with filter 0.
- INDIO_BUFFER_TRIGGERED: triggered conversions uses injected mode for
launching conversions. DFSDM can use hardware triggers (e.g. STM32 timer
or lptimer), so add INDIO_HARDWARE_TRIGGERED to supported modes.
- INDIO_DIRECT_MODE: Only support DMA-based buffer modes. In case no DMA is
available, only support single conversions.
From userland perspective, to summarize various use cases:
1 - single conversion on any filter:
$ cd iio:deviceX
$ cat in_voltageY_raw
This uses regular a conversion (not continuous)
2 - Using sampling frequency without trigger (single channel, buffer)
$ cd iio:deviceX
$ echo 100 > sampling_frequency
$ echo "" > trigger/current_trigger
$ echo 1 > scan_elements/in_voltageY_en
$ echo 1 > buffer/enable
This uses regular conversion in continuous mode (Frequency is achieved
by tuning filter parameters)
3 - sync mode with filter 0: other filters can be converted when using
"st,filter0-sync" dt property. The conversions will get started at the
same time as filter 0. So for any filters > 1:
$ cd iio:deviceX
$ echo 100 > sampling_frequency
$ echo "" > trigger/current_trigger
$ echo 1 > scan_elements/in_voltageY_en
$ echo 1 > buffer/enable
Then start filter 0 as in 2 above.
4 - Using a hardware trigger (with one channel):
- check trigger, configure it:
$ cat /sys/bus/iio/devices/trigger1/name
tim6_trgo
$ echo 100 > /sys/bus/iio/devices/trigger1/sampling_frequency
- go to any filter:
$ echo 1 > scan_elements/in_voltageY_en
$ echo tim6_trgo > trigger/current_trigger
$ echo 1 > buffer/enable
This uses injected conversion as it uses a hardware trigger (without scan)
5 - Using a hardware trigger (with 2+ channel):
Same as in 4/ above, but enable two or more channels in scan_elements.
This uses injected conversion as it uses a hardware trigger (with scan mode)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to support multiple channels in buffer mode, add support for scan
mode. This is precursor patch to ease support of triggered buffer mode.
Currently, only audio uses buffer mode: Regular continuous conversions
with a single channel (per filter).
DFSDM hardware supports scan mode (only) with injected conversions.
Conversions can be launched by software (JSWSTART), trigger or
synchronously with filter 0 (e.g. JSYNC). Continuous conversion mode isn't
available for injected.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Optionally enable IIO hw consumer, when provided (e.g. for DFSDM_IIO type).
This is precursor patch to introduce buffer modes.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move DMA slave configuration to start routine: depending on regular or
injected mode is in use, DMA needs to read resp. RDATAR or JDATAR.
This is precursor patch to introduce injected mode (used for scan).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move DMA enable (e.g. set RDMAEN bit) away from start_conv() that is used
for both buffer and single conversions. Thus, single conv rely on
interrupt, not dma.
Note: take care to prepare all DMA stuff and set RDMAEN before starting
filter (can be set only when DFEN=0).
This is precursor patch to ease support of triggered buffer mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
DFSDM regular continuous mode usage depends on current mode (not DMA):
- for single conversion, RCONT doesn't need to be set.
- for buffer mode, RCONT has to be set (e.g. INDIO_BUFFER_SOFTWARE
used by audio currently).
This is related to filter configuration, move it to relevant routine.
This is precursor patch to ease support of triggered buffer mode.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Current ckout divider may be set to a value that makes ckout to exceed
spi-max-frequency. Rather use lower value (e.g. round up divider when
ckout isn't accurate).
Also when the SPI clock isn't accurate, 'spi_master_freq' is filled in
with expected frequency. Use computed value instead to be more accurate:
- e.g. source clock / (CKOUTDIV + 1)
Enforce checks on the divider: ckoutdiv range can be from 1-255 to provide
divider of 2-256.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- Fix CHECK Macro argument 'wordsize' may be better as '(wordsize)' to avoid precedence issues
Slightly modified by Jonathan to take into account the staging graduation
and a copy and paste version of the same item on the following line.
Signed-off-by: Vladimir Petrigo <vladimir.petrigo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move ad7780 ADC driver out of staging and into the mainline.
The ad7780 is a sigma-delta analog to digital converter. This driver provides
reading voltage values and status bits from both the ad778x and ad717x series.
Its interface also allows writing on the FILTER and GAIN GPIO pins on the
ad778x.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Co-developed-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Until now this driver only exposed the raw value of the channels. With
this patch, the scale value is also exposed.
It depends of a regulator supply, and unlike most of the other driver, do
not having this regulator won't prevent to use the driver. The reason for
it is to allow to continue to use this driver with an old device tree. If
there is no regulator supply then the scale won't be exposed.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A few headers is useless: remove them.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sort the headers in alphabetic order in order to ease the maintenance for
this part.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A return statement is indented one level too deeply; clean this
up by removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Formatting of Kconfig files doesn't look so pretty, so just
take damp cloth and clean it up.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/iio/adc/stmpe-adc.c:204:13: warning: variable 'data' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
Clang can't tell that data will never be used uninitialized because the
two if statements take care of all cases. Remove the first if statement
and make it the else branch of the second one so that it is apparent to
Clang that all cases are covered.
Link: https://github.com/ClangBuiltLinux/linux/issues/387
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: NIck Desaulniers <ndesaulniers@google.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS79XX has GPIO pins that can be used. Add support for the GPIO
pins using the GPIO chip framework.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
devm_iio_trigger_alloc may fail and return NULL. The fix returns
ENOMEM when it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update the module author to the current email address.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the SAR ADC driver for the Amlogic Meson-G12A SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Solves checkpath.pl's message:
CHECK: Comparison to NULL could be written "!indio_dev"
Signed-off-by: Bárbara Fernandes <barbara.fernandes@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Put macro argument between parenthesis in order to avoid precedence
issues. Solves the following checkpath.pl's messages:
CHECK: Macro argument 'mode' may be better as '(mode)' to avoid
precedence issues
CHECK: Macro argument 'channel' may be better as '(channel)' to
avoid precedence issues
CHECK: Macro argument reuse 'sequence' - possible side-effects?
CHECK: Macro argument 'sequence' may be better as '(sequence)' to
avoid precedence issues
CHECK: Macro argument 'val' may be better as '(val)' to avoid
precedence issues
CHECK: Macro argument 'dec' may be better as '(dec)' to avoid precedence
issues
CHECK: Macro argument 'bits' may be better as '(bits)' to avoid
precedence issues
Signed-off-by: Bárbara Fernandes <barbara.fernandes@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace use of the operation '<<' by the BIT macro. Solves checkpath.pl's
message:
CHECK: Prefer using the BIT macro
Signed-off-by: Bárbara Fernandes <barbara.fernandes@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Get broken line aligned with parenthesis on upper line. Solves
checkpatch.pl's message:
CHECK: Alignment should match open parenthesis
Signed-off-by: Bárbara Fernandes <barbara.fernandes@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Indio->mlock is used for protecting the different iio device modes.
It is currently not being used in this way. Replace the lock with
an internal lock specifically used for protecting the SPI transfer
buffer.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The desired channel has to be selected in order to correctly fill the
buffer with the corresponding data.
The `ad_sd_write_reg()` already does this, but for the
`ad_sd_read_reg_raw()` this was omitted.
Fixes: af3008485e ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In remove, the clock is disabled before canceling the
delayed work. This means that the delayed work may be
touching unclocked hardware.
Fix by disabling the clock after the delayed work is
fully canceled. This is consistent with the probe error
path order.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If probe errors out after request_irq(), its error path
does not explicitly cancel the delayed work, which may
have been scheduled by the interrupt handler.
This means the delayed work may still be running when
the core frees the private structure (struct xadc).
This is a potential use-after-free.
Fix by inserting cancel_delayed_work_sync() in the probe
error path.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When cancel_delayed_work() returns, the delayed work may still
be running. This means that the core could potentially free
the private structure (struct xadc) while the delayed work
is still using it. This is a potential use-after-free.
Fix by calling cancel_delayed_work_sync(), which waits for
any residual work to finish before returning.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Having a brief look at at91_adc_read_raw() it is obvious that in the case
of a timeout the setting of AT91_ADC_CHDR and AT91_ADC_IDR registers is
omitted. If 2 different channels are queried we can end up with a
situation where two interrupts are enabled, but only one interrupt is
cleared in the interrupt handler. Resulting in a interrupt loop and a
system hang.
Signed-off-by: Georg Ottinger <g.ottinger@abatec.at>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging/iio driver pull request for 5.1-rc1.
Lots of good IIO driver updates and cleanups in here as always.
Combined with the removal of the xgifb driver, we have a net "loss" of
over 9000 lines in the pull request, always a nice thing.
As the outreachy application process is currently happening, there are
loads of tiny checkpatch cleanup fixes all over the staging tree, which
accounts for the majority of the fixups.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+gLQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymBiQCeJpoBhG+W3r+kP8w65ZY8qU+/liIAn0Tkl4/k
IX1dQzCsEpO1jA8AHj6n
=7wCH
-----END PGP SIGNATURE-----
Merge tag 'staging-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big staging/iio driver pull request for 5.1-rc1.
Lots of good IIO driver updates and cleanups in here as always.
Combined with the removal of the xgifb driver, we have a net "loss" of
over 9000 lines in the pull request, always a nice thing.
As the outreachy application process is currently happening, there are
loads of tiny checkpatch cleanup fixes all over the staging tree,
which accounts for the majority of the fixups"
* tag 'staging-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (341 commits)
staging: mt7621-dma: remove license boilerplate text
staging: mt7621-dma: add SPDX GPL-2.0+ license identifier
Staging: ks7010: Replace typecast to int
Staging: vt6655: Align a static function declaration
staging: speakup: fix line over 80 characters.
staging: mt7621-eth: Remove license boilerplate text
staging: mt7621-eth: Add SPDX license identifier
staging: ks7010: removed custom Michael MIC implementation.
staging: rtl8192e: Fix space and suspect issue
Staging: vt6655: Modify comment style of SPDX License Identifier
Staging: vt6655: Modify comment style for SPDX-License-Identifier
Staging: vt6655: Align a function declaration
Staging: vt6655: Alignment of function declaration
staging: rtl8712: Fix indentation issue
staging: wilc1000: fix incorrent type in initializer
staging: rtl8188eu: remove unused P2P_PRIVATE_IOCTL_SET_LEN
staging: rtl8188eu: remove unused enum P2P_PROTO_WK_ID
staging: rtl8723bs: Remove duplicated include from drv_types.h
Staging: vt6655: Alignment should match open parenthesis
staging: erofs: fix mis-acted TAIL merging behavior
...
The pm8xxx_get_channel() implementation is unclear, and causes gcc to
suddenly generate odd warnings. The trigger for the warning (at least
for me) was the entirely unrelated commit 79a4e91d1b ("device.h: Add
__cold to dev_<level> logging functions"), which apparently changes gcc
code generation in the caller function enough to cause this:
drivers/iio/adc/qcom-pm8xxx-xoadc.c: In function ‘pm8xxx_xoadc_probe’:
drivers/iio/adc/qcom-pm8xxx-xoadc.c:633:8: warning: ‘ch’ may be used uninitialized in this function [-Wmaybe-uninitialized]
ret = pm8xxx_read_channel_rsv(adc, ch, AMUX_RSV4,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
&read_nomux_rsv4, true);
~~~~~~~~~~~~~~~~~~~~~~~
drivers/iio/adc/qcom-pm8xxx-xoadc.c:426:27: note: ‘ch’ was declared here
struct pm8xxx_chan_info *ch;
^~
because gcc for some reason then isn't able to see that the termination
condition for the "for( )" loop in that function is also the condition
for returning NULL.
So it's not _actually_ uninitialized, but the function is admittedly
just unnecessarily oddly written.
Simplify and clarify the function, making gcc also see that it always
returns a valid initialized value.
Cc: Joe Perches <joe@perches.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a few late breaking fixes in here that weren't worth trying to
rush into 5.0 as they have been with us for quite a while.
New device support
* ad7476
- add support for TI ADS786X parts that are compatible with this Analog
Devices driver. Good to see some simple devices are so similar.
* Ingenic jz47xx SoC ADCs
- new driver and bindings
* Plantower PMS7003 partical sensor
- new driver and bindings including vendor prefix.
* TI DAC7612
- new driver and bindings for this dual DAC.
New features
* ad7768-1
- Sampling frequency control
* bmi160
- Data ready trigger support, including open-drain dt binding.
Cleanup / minor fixes.
* Analog Device DACs
- Fix some inconsistent licenses. These are only ones where there were
two different license marked in the same file, and hence were previously
unclear.
* ads124s08
- Spelling fix.
* adxl345
- Parameter alignement tidy up.
* bmi160
- SPDX
- correct a note on the types of supported interrupts which was too strict.
- use iio_pollfunc_store_time to grab an earlier timestamp.
- use if (ret) instead of if (ret < 0) to be consistent whilst simplifying
some handling where ret was effectively getting written to 0 even though
it was always already 0.
* exynos_adc
- Fix a null pointer dereference on unbind.
- Fix number of channels on Exynos4x12 devices to be 4 rather than 8.
* lpc32xx-adc
- Move DT bindings doc out of staging. Oops, I missed this one when
moving the driver.
- SPDX.
* npcm-adc
- drop documentation of reset node as going to be done differently.
It's a new driver this cycle so no need to support the previous
binding going forwards.
* sps30
- Fix an issue with a loop timeout test that meant it would never identify
a timeout.
- Mark deliberate switch fall throughs.
-----BEGIN PGP SIGNATURE-----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=Se+F
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.1b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, features and cleanup for IIO in the 5.1 cycle.
There are a few late breaking fixes in here that weren't worth trying to
rush into 5.0 as they have been with us for quite a while.
New device support
* ad7476
- add support for TI ADS786X parts that are compatible with this Analog
Devices driver. Good to see some simple devices are so similar.
* Ingenic jz47xx SoC ADCs
- new driver and bindings
* Plantower PMS7003 partical sensor
- new driver and bindings including vendor prefix.
* TI DAC7612
- new driver and bindings for this dual DAC.
New features
* ad7768-1
- Sampling frequency control
* bmi160
- Data ready trigger support, including open-drain dt binding.
Cleanup / minor fixes.
* Analog Device DACs
- Fix some inconsistent licenses. These are only ones where there were
two different license marked in the same file, and hence were previously
unclear.
* ads124s08
- Spelling fix.
* adxl345
- Parameter alignement tidy up.
* bmi160
- SPDX
- correct a note on the types of supported interrupts which was too strict.
- use iio_pollfunc_store_time to grab an earlier timestamp.
- use if (ret) instead of if (ret < 0) to be consistent whilst simplifying
some handling where ret was effectively getting written to 0 even though
it was always already 0.
* exynos_adc
- Fix a null pointer dereference on unbind.
- Fix number of channels on Exynos4x12 devices to be 4 rather than 8.
* lpc32xx-adc
- Move DT bindings doc out of staging. Oops, I missed this one when
moving the driver.
- SPDX.
* npcm-adc
- drop documentation of reset node as going to be done differently.
It's a new driver this cycle so no need to support the previous
binding going forwards.
* sps30
- Fix an issue with a loop timeout test that meant it would never identify
a timeout.
- Mark deliberate switch fall throughs.
* tag 'iio-for-5.1b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (26 commits)
iio: adc: exynos-adc: Use proper number of channels for Exynos4x12
dt-binding: iio: remove rst node from NPCM ADC document
dt-bindings: iio: chemical: pms7003: add device tree support
dt-bindings: add Plantower to the vendor prefixes
iio: chemical: add support for Plantower PMS7003 sensor
iio:chemical:sps30 Supress some switch fallthrough warnings.
iio:adc:lpc32xx use SPDX-License-Identifier
dt-bindings: iio: adc: move lpc32xx-adc out of staging
iio: adc: ads124s08: fix spelling mistake "converions" -> "conversions"
iio: adc: exynos-adc: Fix NULL pointer exception on unbind
iio: chemical: sps30: fix a loop timeout test
iio:accel:adxl345: Change alignment to match paranthesis
iio:dac:dac7612: device tree bindings
iio:dac:ti-dac7612: Add driver for Texas Instruments DAC7612
iio: adc: ad7476: Add support for TI ADS786X ADCs
iio: adc: ad7768-1: Add support for setting the sampling frequency
drivers: iio: dac: Fix wrong license for ADI drivers
IIO: add Ingenic JZ47xx ADC driver.
dt-bindings: iio/adc: Add bindings for Ingenic JZ47xx SoCs ADC.
dt-bindings: iio/adc: Add docs for Ingenic JZ47xx SoCs ADC.
...
Exynos4212 and Exynos4412 have only four ADC channels so using
"samsung,exynos-adc-v1" compatible (for eight channels ADCv1) on them is
wrong. Add a new compatible for Exynos4x12.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the driver to SPDX license description which allow removing
several lines in the file.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a spelling mistake in several dev_err messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix NULL pointer exception on device unbind when device tree does not
contain "has-touchscreen" property. In such case the input device is
not registered so it should not be unregistered.
$ echo "12d10000.adc" > /sys/bus/platform/drivers/exynos-adc/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000474
...
(input_unregister_device) from [<c0772060>] (exynos_adc_remove+0x20/0x80)
(exynos_adc_remove) from [<c0587d5c>] (platform_drv_remove+0x20/0x40)
(platform_drv_remove) from [<c05860f0>] (device_release_driver_internal+0xdc/0x1ac)
(device_release_driver_internal) from [<c0583ecc>] (unbind_store+0x60/0xd4)
(unbind_store) from [<c031b89c>] (kernfs_fop_write+0x100/0x1e0)
(kernfs_fop_write) from [<c029709c>] (__vfs_write+0x2c/0x17c)
(__vfs_write) from [<c0297374>] (vfs_write+0xa4/0x184)
(vfs_write) from [<c0297594>] (ksys_write+0x4c/0xac)
(ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Fixes: 2bb8ad9b44 ("iio: exynos-adc: add experimental touchscreen support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Texas Instruments ADS7866, ADS7867 and ADS7868
8/10/12 bit Single channel ADC.
Datasheet: http://www.ti.com/lit/ds/symlink/ads7868.pdf
Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7768-1 core ADC receives a master clock signal (MCLK). The MCLK
frequency combined with the MCLK division and the digital filter
decimation rates, determines the sampling frequency. Along with
MCLK_DIV, the power mode is also configured according to datasheet
recommendations.
From user space, available sampling frequencies can be read. However,
it is not required for an exact value to be entered, since the driver
will look for the closest available match.
When the device configuration changes (for example, if the filter
decimation rate changes), a SYNC_IN pulse is required.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add an IIO driver for the ADC hardware present on Ingenic JZ47xx SoCs.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A number of interesting new devices supported plus a good set of staging
cleanup including one graduation and one drop.
New device support
* ad56886
- Add support for AD5674R/AD5679R with some minor driver changes to support
more channels.
* ad7768
- New driver and dt bindings for this 24 bit ADC.
* max44009
- New driver and dt bindings for this ambient light sensor.
* mpu6050
- Support the ICM 20602 IMU. Minor tweaks due to slightly different
register map.
* NPCM adc
- New driver and dt bindings for this BMC ADC.
* Sensiron SGP30
- Modifiers for ethanol and H2.
- New driver and dt bindings.
- Follow patch added self cleaning support.
* Sensiron SPS30
- New channel type for mass concentration.
- New driver and bindings.
- Minor tidy up patch followed (drop fmt specifier as unused)
* st_pressure
- lps22hh support. ID plus information structures and dt bindings.
* ti-ads124s08
- Add binding doc and driver.
Staging graduations
* ad7606 driver and bindings.
Staging drops
* ad7152 CDC driver dropped. This part is near EoL and no one is known
to be using it. If anyone surfaces obviously we can bring the driver
back. If not, good to drop it to avoid wasting anyone's time cleaning
it up.
New features
* bme680
- DT support and bindings doc.
* isl29018
- Add regulator for VCC.
* mag3110
- Add regulators for supplies.
* meson-saradc
- Support the temperature sensors of more SoCs.
* mma8452
- Add regulators for power suplies and binding docs to reflect them.
* st-accel
- Support the undocumented but it seems fairly common _ONT ACPI method
to specify orientation of the sensor.
Cleanup, minor fixes and fixes for staging driver that have been broken a
long time
* ad5933
- Drop platform data alternative to specifying the reference voltage
using a regulator.
- Use the clock framework to contorl the reference clock.
- Add a DT binding doc to cover the defacto binding.
* ad7280a
- Split up some big functions to improve readability.
* ad7606
- Allow for timeout if interrupt never occurs.
- Use devm functions to simplify probe and remove.
- Use the find_closest macro to avoid need for precise values from
userspace.
- Add missing vendor prefixes for various DT properties. Note the
driver is in staging still and there are no known devicetrees.
- Add explict OF device ID table.
- Simplify the Kconfig choices
- Change to a threaded IRQ.
- SPDX and simple stype fixes.
* ad7816
- Drop unnecessary variable init.
* ad9523
- Check a return value that was ignored.
* ad9833
- Drop platform data. It was just setting most values to the hardware
defaults.
- Use the clock framework to provide the input clock.
* adt7316 (lots of staging cleanup)
- Fix some wrong register / bit definitions
- Invert the logic of the check for an ldac pin so it actually makes sense.
- Read the right register to get internal vref settings
- Allow adt751x chips to use the internal vref for all DAC channels rather
than a subset.
- Remove dac vref bypass control from parts that don't have one.
- Make the store DAC update mode function consistent with the show one.
- Fix some spellings and other minor tidy up.
- Avoid passing irq numbers around by putting all the irq logic in
one place.
- Fix an issue with the resolution of DAC control.
- Fix support of the high resolution DAC mode (for temp proportional output)
where supported.
- Fix DAC read and write calculations.
* st_lsm6dsx
- Drop an unused variable (set but not read)
* xilinx-xadc
- Check an unhandled return value.
-----BEGIN PGP SIGNATURE-----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=M03w
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanup for IIO in the 5.1 cycle
A number of interesting new devices supported plus a good set of staging
cleanup including one graduation and one drop.
New device support
* ad56886
- Add support for AD5674R/AD5679R with some minor driver changes to support
more channels.
* ad7768
- New driver and dt bindings for this 24 bit ADC.
* max44009
- New driver and dt bindings for this ambient light sensor.
* mpu6050
- Support the ICM 20602 IMU. Minor tweaks due to slightly different
register map.
* NPCM adc
- New driver and dt bindings for this BMC ADC.
* Sensiron SGP30
- Modifiers for ethanol and H2.
- New driver and dt bindings.
- Follow patch added self cleaning support.
* Sensiron SPS30
- New channel type for mass concentration.
- New driver and bindings.
- Minor tidy up patch followed (drop fmt specifier as unused)
* st_pressure
- lps22hh support. ID plus information structures and dt bindings.
* ti-ads124s08
- Add binding doc and driver.
Staging graduations
* ad7606 driver and bindings.
Staging drops
* ad7152 CDC driver dropped. This part is near EoL and no one is known
to be using it. If anyone surfaces obviously we can bring the driver
back. If not, good to drop it to avoid wasting anyone's time cleaning
it up.
New features
* bme680
- DT support and bindings doc.
* isl29018
- Add regulator for VCC.
* mag3110
- Add regulators for supplies.
* meson-saradc
- Support the temperature sensors of more SoCs.
* mma8452
- Add regulators for power suplies and binding docs to reflect them.
* st-accel
- Support the undocumented but it seems fairly common _ONT ACPI method
to specify orientation of the sensor.
Cleanup, minor fixes and fixes for staging driver that have been broken a
long time
* ad5933
- Drop platform data alternative to specifying the reference voltage
using a regulator.
- Use the clock framework to contorl the reference clock.
- Add a DT binding doc to cover the defacto binding.
* ad7280a
- Split up some big functions to improve readability.
* ad7606
- Allow for timeout if interrupt never occurs.
- Use devm functions to simplify probe and remove.
- Use the find_closest macro to avoid need for precise values from
userspace.
- Add missing vendor prefixes for various DT properties. Note the
driver is in staging still and there are no known devicetrees.
- Add explict OF device ID table.
- Simplify the Kconfig choices
- Change to a threaded IRQ.
- SPDX and simple stype fixes.
* ad7816
- Drop unnecessary variable init.
* ad9523
- Check a return value that was ignored.
* ad9833
- Drop platform data. It was just setting most values to the hardware
defaults.
- Use the clock framework to provide the input clock.
* adt7316 (lots of staging cleanup)
- Fix some wrong register / bit definitions
- Invert the logic of the check for an ldac pin so it actually makes sense.
- Read the right register to get internal vref settings
- Allow adt751x chips to use the internal vref for all DAC channels rather
than a subset.
- Remove dac vref bypass control from parts that don't have one.
- Make the store DAC update mode function consistent with the show one.
- Fix some spellings and other minor tidy up.
- Avoid passing irq numbers around by putting all the irq logic in
one place.
- Fix an issue with the resolution of DAC control.
- Fix support of the high resolution DAC mode (for temp proportional output)
where supported.
- Fix DAC read and write calculations.
* st_lsm6dsx
- Drop an unused variable (set but not read)
* xilinx-xadc
- Check an unhandled return value.
* tag 'iio-for-5.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (67 commits)
iio: chemical: sps30: remove printk format specifier
staging: iio: frequency: ad9833: Load clock using clock framework
staging: iio: frequency: ad9833: Get frequency value statically
dt-bindings: iio: light: Add max44009
iio: light: add driver for MAX44009
dt-bindings: iio: adc: Add docs for AD7768-1
iio: adc: Add AD7768-1 ADC basic support
staging: iio: cdc: ad7152: remove driver completely
iio: imu: mpu6050: Add support for the ICM 20602 IMU
dt-bindings: iio: imu: add icm20602 bindings to mpu6050
dt-bindings: iio: pressure: add LPS22HH bindings
iio: st_accel: use ACPI orientation data
iio: adc: add NPCM ADC driver
dt-binding: iio: add NPCM ADC documentation
iio: chemical: sps30: allow changing self cleaning period
dt-bindings: iio: chemical: Add bindings for bme680
iio: chemical: bme680: Add device-tree support
iio:st_pressure:initial lps22hh sensor support
iio: accell: mma8452: add vdd/vddio regulator operation support
dt-bindings: iio: accel: mma8452: add power supplies property
...
Been a busy month, so these are rather later than they should have been.
* atlas-ph-sensor:
- Temperature scale didn't correspond to the ABI.
* axp288:
- A few different fixes around the TS-pin handling.
* ti-ads8688
- Not enough space in the buffer used to build the scan to allow for
the timestamp.
* tools - iio_generic_buffer
- Make num_loops signed so that we really are running for ever
rather than just a long time when we specify -1.
-----BEGIN PGP SIGNATURE-----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=2R0k
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-5.0a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.0 cycle.
Been a busy month, so these are rather later than they should have been.
* atlas-ph-sensor:
- Temperature scale didn't correspond to the ABI.
* axp288:
- A few different fixes around the TS-pin handling.
* ti-ads8688
- Not enough space in the buffer used to build the scan to allow for
the timestamp.
* tools - iio_generic_buffer
- Make num_loops signed so that we really are running for ever
rather than just a long time when we specify -1.
* tag 'iio-fixes-5.0a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: ti-ads8688: Update buffer allocation for timestamps
tools: iio: iio_generic_buffer: make num_loops signed
iio: adc: axp288: Fix TS-pin handling
iio: chemical: atlas-ph-sensor: correct IIO_TEMP values to millicelsius
The ad7768-1 is a single channel, precision 24-bit analog to digital
converter (ADC).
This basic patch configures the device in fast mode, with 32 kSPS and
leaves the default sinc5 filter.
Two data conversion modes are made available. When data is retrieved by
using the read_raw attribute, one shot single conversion mode is set.
The continuous conversion mode is enabled when the triggered buffer
mechanism is used. To assure correct data retrieval, the driver waits
for the interrupt triggered by the low to high transition of the DRDY
pin.
Datasheets:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7768-1.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds an ADC driver for the STMPE device using the industrial
input/output interface. The driver supports raw reading of values.
The driver depends on the MFD STMPE driver. If the touchscreen
block is enabled too, only four of the 8 ADC channels are available.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Add support for Power Supply to AXP813
- Add support for GPIO, ADC, AC and Battery Power Supply to AXP803
- Add support for UART to Exynos LPASS
- Fix-ups
- Use supplied MACROS; ti_am335x_tscadc
- Trivial spelling/whitespace/alignment; tmio, axp20x, rave-sp
- Regmap changes; bd9571mwv, wm5110-tables
- Kconfig dependencies; MFD_AT91_USART
- Supply shared data for child-devices; madera-core
- Use new of_node_name_eq() API call; max77620, stmpe
- Use managed resources (devm_*); tps65218
- Comment descriptions; ingenic-tcu
- Coding style; madera-core
- Bug Fixes
- Fix section mismatches; twl-core, db8500-prcmu
- Correct error path related issues; mt6397-core, ab8500-core, mc13xxx-core
- IRQ related fixes; tps6586x
- Ensure proper initialisation sequence; qcom_rpm
- Repair potential memory leak; cros_ec_dev
-----BEGIN PGP SIGNATURE-----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=BwG/
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support
- Add support for Power Supply to AXP813
- Add support for GPIO, ADC, AC and Battery Power Supply to AXP803
- Add support for UART to Exynos LPASS
Fix-ups:
- Use supplied MACROS; ti_am335x_tscadc
- Trivial spelling/whitespace/alignment; tmio, axp20x, rave-sp
- Regmap changes; bd9571mwv, wm5110-tables
- Kconfig dependencies; MFD_AT91_USART
- Supply shared data for child-devices; madera-core
- Use new of_node_name_eq() API call; max77620, stmpe
- Use managed resources (devm_*); tps65218
- Comment descriptions; ingenic-tcu
- Coding style; madera-core
Bug Fixes:
- Fix section mismatches; twl-core, db8500-prcmu
- Correct error path related issues; mt6397-core, ab8500-core, mc13xxx-core
- IRQ related fixes; tps6586x
- Ensure proper initialisation sequence; qcom_rpm
- Repair potential memory leak; cros_ec_dev"
* tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (25 commits)
mfd: exynos-lpass: Enable UART module support
mfd: mc13xxx: Fix a missing check of a register-read failure
mfd: cros_ec: Add commands to control codec
mfd: madera: Remove spurious semicolon in while loop
mfd: rave-sp: Fix typo in rave_sp_checksum comment
mfd: ingenic-tcu: Fix bit field description in header
mfd: tps65218: Use devm_regmap_add_irq_chip and clean up error path in probe()
mfd: Use of_node_name_eq() for node name comparisons
mfd: cros_ec_dev: Add missing mfd_remove_devices() call in remove
mfd: axp20x: Add supported cells for AXP803
mfd: axp20x: Re-align MFD cell entries
mfd: axp20x: Add AC power supply cell for AXP813
mfd: wm5110: Add missing ASRC rate register
mfd: qcom_rpm: write fw_version to CTRL_REG
mfd: tps6586x: Handle interrupts on suspend
mfd: madera: Add shared data for accessory detection
mfd: at91-usart: Add platform dependency
mfd: bd9571mwv: Add volatile register to make DVFS work
mfd: ab8500-core: Return zero in get_register_interruptible()
mfd: tmio: Typo s/use use/use/
...
Introduce the TI ADS124S08 and the ADS124S06 ADC
devices from TI. The ADS124S08 is the 12 channel ADC
and the ADS124S06 is the 6 channel ADC device
These devices share a common datasheet:
http://www.ti.com/lit/gpn/ads124s08
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Per Jonathan Cameron, the buffer needs to allocate room for a
64 bit timestamp as well as the channels. Change the buffer
to allocate this additional space.
Fixes: 2a86487786 ("iio: adc: ti-ads8688: add trigger and buffer support")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Prior to this commit there were 3 issues with our handling of the TS-pin:
1) There are 2 ways how the firmware can disable monitoring of the TS-pin
for designs which do not have a temperature-sensor for the battery:
a) Clearing bit 0 of the AXP20X_ADC_EN1 register
b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring
Prior to this commit we were unconditionally setting both bits to the
value used on devices with a TS. This causes the temperature protection to
kick in on devices without a TS, such as the Jumper ezbook v2, causing
them to not charge under Linux.
This commit fixes this by using regmap_update_bits when updating these 2
registers, leaving the 2 mentioned bits alone.
The next 2 problems are related to our handling of the current-source
for the TS-pin. The current-source used for the battery temp-sensor (TS)
is shared with the GPADC. For proper fuel-gauge and charger operation the
TS current-source needs to be permanently on. But to read the GPADC we
need to temporary switch the TS current-source to ondemand, so that the
GPADC can use it, otherwise we will always read an all 0 value.
2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl
register, overwriting various other unrelated bits. Specifically we were
overwriting the current-source setting for the TS and GPIO0 pins, forcing
it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet
this was causing us to get a too high adc value (due to a too high
current-source) resulting in the following errors being logged:
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR
This commit fixes this by using regmap_update_bits to change only the
relevant bits.
3) After reading the GPADC channel we were unconditionally enabling the
TS current-source even on devices where the TS-pin is not used and the
current-source thus was off before axp288_adc_read_raw call.
This commit fixes this by making axp288_adc_set_ts a nop on devices where
the ADC is not enabled for the TS-pin.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545
Fixes: 3091141d78 ("iio: adc: axp288: Fix the GPADC pin ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In function xadc_probe, xadc_write_adc_reg can return an error value
when write fails. The fix checks for the return value consistent with
other invocations of the latter function.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8b and Meson8m2 use the same logic to convert the ADC register
value to celsius, which is different from Meson8:
- Meson8 has different multiplier and divider values
- Meson8 uses a 4-bit TSC (temperature sensor coefficient) which fits
into the 4-bit field in the MESON_SAR_ADC_DELTA_10 register:
MESON_SAR_ADC_DELTA_10_TS_C_MASK. Meson8b and Meson8m2 have a 5-bit
TSC which requires writing the upper-most bit into the
MESON_HHI_DPLL_TOP_0[9] register from the HHI register area.
This adds support for the temperature sensor on the Meson8b and Meson8m2
SoCs by implementing the logic to write the upper-most TSC bit into the
HHI register area. The SoC-specific values (temperature_trimming_bits,
temperature_multiplier, temperature_divider) are added - these simply
integrate into the existing infrastructure (which was implemented for
Meson8) and thus require no further changes to the existing temperature
calculation logic.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move ad7606 ADC driver out of staging and into the mainline.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
adc5_get_dt_data uses a local, prop, feeds it to adc5_get_dt_channel_data,
and then puts the result into adc->chan_props. The problem is
adc5_get_dt_channel_data may not initialize that structure fully, so a
garbage value is used for prescale if the optional "qcom,pre-scaling" is
not defined in DT. adc5_read_raw then uses this as an array index,
generating a crash that looks like this:
[ 6.683186] Unable to handle kernel paging request at virtual address ffffff90e78c7964
Call trace:
qcom_vadc_scale_code_voltage_factor+0x74/0x104
qcom_vadc_scale_hw_calib_die_temp+0x20/0x60
qcom_adc5_hw_scale+0x78/0xa4
adc5_read_raw+0x3d0/0x65c
iio_channel_read+0x240/0x30c
iio_read_channel_processed+0x10c/0x150
qpnp_tm_get_temp+0xc0/0x40c
of_thermal_get_temp+0x7c/0x98
thermal_zone_get_temp+0xac/0xd8
thermal_zone_device_update+0xc0/0x38c
qpnp_tm_probe+0x624/0x81c
platform_drv_probe+0xe4/0x11c
really_probe+0x188/0x3fc
driver_probe_device+0xb8/0x188
__device_attach_driver+0x114/0x180
bus_for_each_drv+0xd8/0x118
__device_attach+0x180/0x27c
device_initial_probe+0x20/0x2c
bus_probe_device+0x78/0x124
deferred_probe_work_func+0xfc/0x138
process_one_work+0x3d8/0x8b0
process_scheduled_works+0x48/0x6c
worker_thread+0x488/0x7cc
kthread+0x24c/0x264
ret_from_fork+0x10/0x18
Unfortunately, when I went to add the initializer for this and tried to
boot it, my machine shut down immediately, complaining that it was
hotter than the sun. It appears that adc5_chans_pmic and adc5_chans_rev2
were initializing prescale_index as if it were directly a divisor,
rather than the index into adc5_prescale_ratios that it is.
Fix the uninitialized value, and change the static initialization to use
indices into adc5_prescale_ratios.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make it possible to use Exynos ADC driver on S5PV210 based devices.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
S5PV210's ADC variant is almost the same as v1 except that it has 10
channels and doesn't require the pmu register
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When performing single ended measurements with TSCADC, its recommended
to set negative input (SEL_INM_SWC_3_0) of ADC step to ADC's VREFN in the
corresponding STEP_CONFIGx register.
Also, the positive(SEL_RFP_SWC_2_0) and negative(SEL_RFM_SWC_1_0)
reference voltage for ADC step needs to be set to VREFP and VREFN
respectively in STEP_CONFIGx register.
Without these changes, there may be variation of as much as ~2% in the
ADC's digital output which is bad for precise measurement.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Switch off ADC when going to low power mode, in case it has been left
running in buffer mode. Then re-enable it when resuming.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for runtime PM & sleep. Move all regulator and clock management
to dedicated HW start/stop routines. Then rely on (runtime) PM OPS to
call them.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move self-calibration routine to prepare routine.
- This is precursor patch to ease power management handling.
- This also allow to factorize few error cases (error handling).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this patch we are registering the internal clocks (for example on
Meson8b, where the SAR ADC IP block implements the divider and gate
clocks) with the following names:
- /soc/cbus@c1100000/adc@8680#adc_div
- /soc/cbus@c1100000/adc@8680#adc_en
This is bad because the common clock framework uses the clock to create
a directory in <debugfs>/clk. With such name, the directory creation
(silently) fails and the debugfs entry ends up being created at the
debugfs root.
With this change, the new clock names are:
- c1108680.adc#adc_div
- c1108680.adc#adc_en
This matches the clock naming scheme used in the PWM, Ethernet and MMC
drivers. It also fixes the problem with debugfs.
The idea is shamelessly taken from commit b96e9eb628 ("pwm: meson:
Fix mux clock names").
Fixes: 3921db46a8 ("iio: Convert to using %pOF instead of full_name")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
devm_kasprintf() may return NULL on failure of internal allocation thus
the assignments to init.name are not safe if not checked. On error
meson_sar_adc_clk_init() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Along with the headline feature of 5 new drivers, we have the
substantial addition of auxilliary sensor support on the lsm6sdx
parts for ST. There has also been a good set of staging cleanup
in this period with more underway.
An ever increasing number of devices supported with just a new
ID which is a good sign that at least some manufacturers are
continuing to stabilise their interfaces.
New device support,
* ad7124
- New driver supporting Analog Devices' ad7124-4 and ad7124-8 parts
with the inevitable DT binding.
* ad7949
- New driver supporting Analog Devices' ad7949, AD7682 and AD7689 ADCs.
* rm3100
- New driver supporting PNIs RM3100 magnometer with bindings and
vendor prefix.
* ti-dac7311
- New driver supporting DAC7311, DAC6311 and DAC5311 TI DACs, with
DT bindings.
* vcnl5035
- New driver supporting the light sensor part of the VCNL4035, with
DT bindings
Features,
* bindings
- Add a generic ADC channel binding as we keep reinventing this
wheel.
* adc128s052
- Add IDs for additional pin compatible parts.
- Add APCI ID seen on E3940 UP squared boards.
* ad_sigma_delta
- Allow for custom data register overiding default.
* kxcjk1013
- Add KIOX0009 ACPI ID as seen on the Acer One 10.
* lsm6dsx
- Rework leading to...
- External sensor support using the built in I2C master.
- Initial support for a slave lis2mdl magnetometer.
* meson-saradc
- Add temperature sensor support and bindings.
* st_magn
- New ID for lsm9dsl_magn with bindings
- New ID for lis3de accelerometer
* tpl0102
- Add supprot for IIO_AVAIL_RANGE to report the range available
from this device to userspace and in kernel users.
Cleanups and minor fixes
* tools
- Allow outside specification of CFLAGS
* ad2s90
- Handle and spi_read error.
- Handle spi_setup failure
- Drop a pointless assignment.
- Prevent a potentail race by moving device registration to after
all other setup.
- Add missing scale attribute.
- Add a sanity check on channel type before trying to read it.
* ad2s1210
- Move to modern gpio descriptors.
- Drop a gpioin flag which made no sense as far as we can tell.
- Add dt table (bindings doc to follow when this is ready for
moving out of staging).
* ad5933
- Drop camel-case naming of ext_clk_hz.
- White space fixes.
* ad7150
- Local variable to shorten overly long line.
- Alignment and line break fixes.
* ad7280a
- Handle an error path that was previously ignored.
- Use crc8.h to build the crc table replacing custom code.
- Avoid unecessary cast.
- Power down the device if an error happens in probe
- Use devm routines to simplify probe and remove.
* ad7606
- Alignment fixes.
* ad7780
- This worked as long as by coincidence an uninitialized value
was 0. Lets not rely on that.
- Ensure gain update is only used with the ad778x chips that
actually support it.
- Tidy up pattern mask generation.
- Read regulator when scale is requested (which should be infrequent)
as it might have changed from initialization.
* ad7816
- Move to modern gpio descriptors
- Don't use a busy_pin for ad7818 as there isn't one.
- Ensure RD/WR and CONVST pins are outputs (previously they
were brought up as inputs which doesn't seem to make any sense)
- DT id table.
* adc128s052
- SPDX
* adt7316
- Alignment fix.
- Fix data reading. When using I2C the driver never actually
used the value read. This has been broken a very long time
hence no rush to fix it now + the driver is undergoing a lot
of cleanup.
- Sanity check that the i2c read didn't fail to actually read
anything.
* dpot-dac
- Mark a switch full through with slightly different text so that
gcc doesn't warn on it.
* gyro-adc
- Fix a wrong file in the MAINTAINERS entry and add binding doc to the
listed files.
* ina2xx
- Add some early returns to clarify error paths in switch.
* lsm6dsx
- MAINTAINERS entry.
* max11100
- SPDX
* max9611
- SPDX
* mcp4131
- use of_device_get_match_data in preference to spi_get_device_id
approach.
* rcar-adc
- SPDX
* sc27xx
- Add ADC conversion timeout support to avoid possible fault.
* ssp_sensors
- Don't free managed resources manually.
* st-magn
- Add a comment to avoid future confusion over when to use -magn
postfix (on multi chip in package parts)
- Add BDU register for LIS3MDL where it seems to have been missed.
* st-sensors
- Minor spelling, grammar etc fixes.
* tpl0102
- Use a pointer rather than an index of an array to improve conciseness.
-----BEGIN PGP SIGNATURE-----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=78Y3
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.21 cycle
Along with the headline feature of 5 new drivers, we have the
substantial addition of auxilliary sensor support on the lsm6sdx
parts for ST. There has also been a good set of staging cleanup
in this period with more underway.
An ever increasing number of devices supported with just a new
ID which is a good sign that at least some manufacturers are
continuing to stabilise their interfaces.
New device support,
* ad7124
- New driver supporting Analog Devices' ad7124-4 and ad7124-8 parts
with the inevitable DT binding.
* ad7949
- New driver supporting Analog Devices' ad7949, AD7682 and AD7689 ADCs.
* rm3100
- New driver supporting PNIs RM3100 magnometer with bindings and
vendor prefix.
* ti-dac7311
- New driver supporting DAC7311, DAC6311 and DAC5311 TI DACs, with
DT bindings.
* vcnl5035
- New driver supporting the light sensor part of the VCNL4035, with
DT bindings
Features,
* bindings
- Add a generic ADC channel binding as we keep reinventing this
wheel.
* adc128s052
- Add IDs for additional pin compatible parts.
- Add APCI ID seen on E3940 UP squared boards.
* ad_sigma_delta
- Allow for custom data register overiding default.
* kxcjk1013
- Add KIOX0009 ACPI ID as seen on the Acer One 10.
* lsm6dsx
- Rework leading to...
- External sensor support using the built in I2C master.
- Initial support for a slave lis2mdl magnetometer.
* meson-saradc
- Add temperature sensor support and bindings.
* st_magn
- New ID for lsm9dsl_magn with bindings
- New ID for lis3de accelerometer
* tpl0102
- Add supprot for IIO_AVAIL_RANGE to report the range available
from this device to userspace and in kernel users.
Cleanups and minor fixes
* tools
- Allow outside specification of CFLAGS
* ad2s90
- Handle and spi_read error.
- Handle spi_setup failure
- Drop a pointless assignment.
- Prevent a potentail race by moving device registration to after
all other setup.
- Add missing scale attribute.
- Add a sanity check on channel type before trying to read it.
* ad2s1210
- Move to modern gpio descriptors.
- Drop a gpioin flag which made no sense as far as we can tell.
- Add dt table (bindings doc to follow when this is ready for
moving out of staging).
* ad5933
- Drop camel-case naming of ext_clk_hz.
- White space fixes.
* ad7150
- Local variable to shorten overly long line.
- Alignment and line break fixes.
* ad7280a
- Handle an error path that was previously ignored.
- Use crc8.h to build the crc table replacing custom code.
- Avoid unecessary cast.
- Power down the device if an error happens in probe
- Use devm routines to simplify probe and remove.
* ad7606
- Alignment fixes.
* ad7780
- This worked as long as by coincidence an uninitialized value
was 0. Lets not rely on that.
- Ensure gain update is only used with the ad778x chips that
actually support it.
- Tidy up pattern mask generation.
- Read regulator when scale is requested (which should be infrequent)
as it might have changed from initialization.
* ad7816
- Move to modern gpio descriptors
- Don't use a busy_pin for ad7818 as there isn't one.
- Ensure RD/WR and CONVST pins are outputs (previously they
were brought up as inputs which doesn't seem to make any sense)
- DT id table.
* adc128s052
- SPDX
* adt7316
- Alignment fix.
- Fix data reading. When using I2C the driver never actually
used the value read. This has been broken a very long time
hence no rush to fix it now + the driver is undergoing a lot
of cleanup.
- Sanity check that the i2c read didn't fail to actually read
anything.
* dpot-dac
- Mark a switch full through with slightly different text so that
gcc doesn't warn on it.
* gyro-adc
- Fix a wrong file in the MAINTAINERS entry and add binding doc to the
listed files.
* ina2xx
- Add some early returns to clarify error paths in switch.
* lsm6dsx
- MAINTAINERS entry.
* max11100
- SPDX
* max9611
- SPDX
* mcp4131
- use of_device_get_match_data in preference to spi_get_device_id
approach.
* rcar-adc
- SPDX
* sc27xx
- Add ADC conversion timeout support to avoid possible fault.
* ssp_sensors
- Don't free managed resources manually.
* st-magn
- Add a comment to avoid future confusion over when to use -magn
postfix (on multi chip in package parts)
- Add BDU register for LIS3MDL where it seems to have been missed.
* st-sensors
- Minor spelling, grammar etc fixes.
* tpl0102
- Use a pointer rather than an index of an array to improve conciseness.
* tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (80 commits)
Staging: iio: adt7316: Add an extra check for 'ret' equals to 0
Staging: iio: adt7316: Fix i2c data reading, set the data field
dt-bindings: iio: adc: Add docs for ad7124
iio: adc: Add ad7124 support
dt-bindings: iio: adc: Add common ADCs properties to a separate file
iio: ad_sigma_delta: Allow to provide custom data register address
staging: iio: ad7816: Add device tree table.
iio: imu: st_lsm6dsx: add entry in MAINTAINERS file
iio: potentiometer: mcp4131: use of_device_get_match_data()
staging: iio: adc: ad7280a: use devm_* APIs
staging: iio: adc: ad7280a: power down the device on error in probe
dt-bindings: iio: imu: st_lsm6dsx: add support to i2c pullup resistors
iio: imu: st_lsm6dsx: add hw FIFO support to i2c controller
iio: imu: st_lsm6dsx: add st_lsm6dsx_push_tagged_data routine
iio: imu: st_lsm6dsx: add i2c embedded controller support
iio: imu: st_lsm6dsx: introduce st_lsm6dsx_sensor_set_enable routine
iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids
iio: imu: st_lsm6dsx: remove static from st_lsm6dsx_set_watermark
iio: imu: st_lsm6dsx: reload trimming parameter at bootstrap
iio: imu: st_lsm6dsx: introduce locked read/write utility routines
...
The ad7124-4 and ad7124-8 are a family of 4 and 8 channel sigma-delta ADCs
with 24-bit precision and reference.
Three power modes are available which in turn affect the output data rate:
* Full power: 9.38 SPS to 19,200 SPS
* Mid power: 2.34 SPS to 4800 SPS
* Low power: 1.17 SPS to 2400 SPS
The ad7124-4 can be configured to have four differential inputs, while
ad7124-8 can have 8. Moreover, ad7124 also supports per channel
configuration. Each configuration consists of gain, reference source,
output data rate and bipolar/unipolar configuration.
Datasheets:
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/AD7124-4.pdf
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/ad7124-8.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some newer devices from the Sigma-Delta ADC family do have their data
register at a different address than the current default address. Add a
parameter to the ad_sigma_delta_info struct which allows to override the
default address.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sometimes the ADC controller met some problems, and it will not complete
the data conversion, that will can not wake up the read process any more
to block users. So we should add one maximum conversion time to avoid
this issue.
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Channel 6 of the SAR ADC can be switched between two inputs:
SAR_ADC_CH6 input (an actual pad on the SoC) and the signal from the
temperature sensor inside the SoC.
To get usable results from the temperature sensor we need to read the
corresponding calibration data from the eFuse and pass it to the SAR ADC
registers. If the temperature sensor is not calibrated (the eFuse data
contains a bit for this) then the driver will only register the
iio_chan_spec's for voltage measurements.
This only enables the temperature sensor for the Meson8 SoC. Meson8b and
Meson8m2 SoCs can be supported in the future as well but we first need
a way to pass the fifth TSC (temperature sensor coefficient) bit to the
HHI register area (apart from that the infrastructure as already
implemented for Meson8 can be used). On the 64-bit SoCs (GXBB, GXL and
GXM) the temperature sensor inside SAR ADC is firmware-controlled (by
BL30, we can simply use the SCPI hwmon driver to get the chip
temperature).
To keep the devicetree interface backwards compatible we simply skip the
temperature sensor initialization if no eFuse nvmem cell is passed via
devicetree.
The public documentation for the SAR ADC IP block does not explain how
to use the registers to read the temperature. The logic from this patch
is based on reading and understanding Amlogic's GPL kernel sources.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Compatible with AD7682 and AD7689 chips.
It is a Analog Devices ADC driver 14/16 bits 4/8 channels
with SPI protocol
Datasheet of the device:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7949.pdf
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This updates the ti-adc128s052.c file to use SPDX-License-Identifier
instead of more verbose license text.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI _HID AANT1280 matches an ADC124S101 present on E3940 SKUs of the UP
Squared board.
Add it to the driver.
Signed-off-by: Nicola Lunghi <nicola.lunghi@emutex.com>
[javier@emutex.com: fix up commit message and one checkpatch warning]
Signed-off-by: Javier Arteaga <javier@emutex.com>
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The datasheets for ADC122S021 and ADC124S021 list two more
pin-compatible alternatives for each device.
Add their IDs as compatible strings.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Javier Arteaga <javier@emutex.com>
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument device
support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a bit
"late" due to them getting stuck on my laptop during travel to the
Mantainers summit.
When merging with your tree, there will be 2 merge conflicts, both files
will be simple to resolve, just delete them :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9bSGA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk5eACfYp73m9tLO22rnBcXJ73bWAYSTOMAn2GEL4Nc
LZBXs8QvvJIwfqmi7ofn
=UWJn
-----END PGP SIGNATURE-----
Merge tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver pull request for 4.20-rc1.
There are lots of things here, we ended up adding more lines than
removing, thanks to a large influx of Comedi National Instrument
device support. Someday soon we need to get comedi out of staging...
Other than the comedi drivers, the "big" things here are:
- new iio drivers
- delete dgnc driver (no one used it and no one had the hardware
anymore)
- vbox driver updates and fixes
- erofs fixes
- tons and tons of tiny checkpatch fixes for almost all staging
drivers
All of these have been in linux-next, with the last few happening a
bit "late" due to them getting stuck on my laptop during travel to the
Mantainers summit"
* tag 'staging-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (690 commits)
staging: gasket: Fix sparse "incorrect type in assignment" warnings.
staging: gasket: remove debug logs for callback invocation
staging: gasket: remove debug logs in page table mapping calls
staging: rtl8188eu: core: Use sizeof(*p) instead of sizeof(struct P) for memory allocation
staging: ks7010: Remove extra blank line
staging: gasket: Remove extra blank line
staging: media: davinci_vpfe: Fix spelling mistake in enum
staging: speakup: Add a pair of braces
staging: wlan-ng: Replace long int with long
staging: MAINTAINERS: remove obsolete IPX staging directory
staging: MAINTAINERS: remove NCP filesystem entry
staging: rtl8188eu: cleanup comparsions to false
staging: gasket: Update device virtual address comment
staging: gasket: sysfs: fix attribute release comment
staging: gasket: apex: fix sysfs_show
staging: gasket: page_table: simplify gasket_components_to_dev_address
staging: gasket: page_table: fix comment in components_to_dev_address
staging: gasket: page table: fixup error path allocating coherent mem
staging: gasket: page_table: rearrange gasket_page_table_entry
staging: gasket: page_table: remove unnecessary PTE status set to free
...
Static analysis with CoverityScan is throwing warnings that specific
case statements are missing breaks. Rather than adding breaks, add
return -EINVAL to the specific case statements to clarify the
error return paths. Fix also saves 50 bytes.
Before:
text data bss dec hex filename
21418 4936 128 26482 6772 drivers/iio/adc/ina2xx-adc.o
After:
dec hex filename
21370 4936 128 26434 6742 drivers/iio/adc/ina2xx-adc.o
(gcc 8.2, x86-64)
Detected by CoverityScan, CID#1462408 ("Missing break in switch")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Parent MFD device takes care of enabling ADC interface whenever
touchscreen is marked wakeup capable. Therefore, unconditionally disable
ADC interface during system suspend to save power in case of system with
just ADC and no TSC.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Until now the "channel" number is identical to how the channel is
identified inside the (FIFO) registers. In our case we have eight
channels and the hardware also has eight inputs.
However, there are two special inputs:
- channel 6 can select between the SAR_ADC_CH6 pad and the chip's
internal temperature sensor
- channel 7 can select between SAR_ADC_CH7 and VSS, VDD / 4, VDD / 2,
VDD * 3 / 4 and VDD.
When programming the registers to read for example the temperature
sensor we have to select FIFO channel 6, set the correct bit which muxes
channel 6 to the temperature sensor and then start the ADC measurement
for channel 6 as usual.
When we add support for the temperature sensor the driver has to know
about that it has to use FIFO channel 6 to measure using the chip's
internal temperature sensor. However, in that case the iio_chan_spec
channel will not be 6 because this is already used for the SAR_ADC_CH6
pad input. Thus we use iio_chan_spec's address field to store the FIFO
channel number for each channel.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In the future we may support two different channel sets:
- one which includes the voltage pads and the temperature sensor output
(for Meson8, Meson8b and Meson8m2)
- one which only includes the voltage pads (GXBB, GXL, GXM and AXG)
Channel 7 has a special function on all of these platforms. However,
since we will have different channel array definitions we want our code
to always use whatever channels struct iio_dev uses.
No functional changes for now. This is the preparation for adding
temperature sensor support to this driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When channels are registered, the hardware channel number is not the
actual iio channel number.
This is because the driver is probed with a certain number of accessible
channels. Some pins are routed and some not, depending on the description of
the board in the DT.
Because of that, channels 0,1,2,3 can correspond to hardware channels
2,3,4,5 for example.
In the buffered triggered case, we need to do the translation accordingly.
Fixed the channel number to stop reading the wrong channel.
Fixes: 0e589d5fb ("ARM: AT91: IIO: Add AT91 ADC driver.")
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When doing simple conversions, the driver did not acknowledge the DRDY irq.
If this irq status is not acked, it will be left pending, and as soon as a
trigger is enabled, the irq handler will be called, it doesn't know why
this status has occurred because no channel is pending, and then it will go
int a irq loop and board will hang.
To avoid this situation, read the LCDR after a raw conversion is done.
Fixes: 0e589d5fb ("ARM: AT91: IIO: Add AT91 ADC driver.")
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 053ffe3c8c ("iio: adc: meson-saradc: squash and share the
common adc platform data") put all the data which is needed at runtime
from struct meson_sar_adc_data to a new struct meson_sar_adc_param so
we can re-use the platform specific configuration without having to
duplicate everything just to change the name.
The only place where struct meson_sar_adc_data is now needed is the
_probe function which has to pass the name to the iio_dev. All other
functions only need access to struct meson_sar_adc_param. This means we
can simplify struct meson_sar_adc_priv.
The goal of this patch is to make the code a bit easier to read since
this removes one level of nesting. No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This simplifies our _probe function by using of_device_get_match_data
instead of open-coding it. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This define is of no use because the driver is avoiding shifting bits
by itself but using FIELD_GET/FIELD_PREP (which are using bit masks)
instead. There is already a MESON_SAR_ADC_DELTA_10_TS_C_MASK bit mask so
MESON_SAR_ADC_DELTA_10_TS_C_SHIFT was redundant.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Leaving for_each_child_of_node loop we should release child device node,
if it is not stored for future use.
Found by Linux Driver Verification project (linuxtesting.org).
JC: I'm not sending this as a quick fix as it's been wrong for years,
but good to pick up for stable after the merge window.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 6df2e98c3e ("iio: adc: Add imx25-gcq ADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This changes how the SPI message for the triggered buffer is setup in
the TI ADS7950 A/DC driver. By using the SPI_CS_WORD flag, we can read
multiple samples in a single SPI transfer. If the SPI controller
supports DMA transfers, we can see a significant reduction in CPU usage.
For example, on an ARM9 system running at 456MHz reading just 4 channels
at 100Hz: before this change, top shows the CPU usage of the IRQ thread
of this driver to be ~7.7%. After this change, the CPU usage drops to
~3.8%.
The use of big-endian for the raw data was cargo culted from another
driver when this driver was originally written. It used an SPI word size
of 8 bits and big-endian byte ordering to effectively emulate 16 bit
words.
Now, in order to inject a CS toggle between each word, we need to use
the correct word size, otherwise we would get a CS toggle half way
through each word 16-bit. The SPI subsystem uses CPU byte ordering for
multi-byte words. So, the data we get back from the SPI is going to be
CPU endian now no matter what. Converting that to big endian will just
add overhead on little endian systems so we opt to change the raw data
format from big endian to CPU endian.
There is a small risk that this could break some lazy userspace programs
that use the raw data without checking the data format. We can address
this if/when it actually comes up.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver only defines a subset of all possible ADC channels. Channel
numbers read from the device tree are accepted as long as they don't
exceed a max value, even when no channel definition exists. Add a
check to abort initialization in this case.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support to read calibration values from the eFuse
controller to calibrate the ADC channel scales, which can make ADC
sample data more accurate.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The headset device will use channel 20 of ADC controller to detect events,
but it needs the raw ADC data to do conversion according to its own formula.
Thus we should configure the channel mask separately and configure channel
20 as IIO_CHAN_INFO_RAW, as well as adding raw data read support.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MCP3911 is a dual channel Analog Front End (AFE) containing two
synchronous sampling delta-sigma Analog-to-Digital Converters (ADC).
Co-developed-by: Kent Gustavsson <kent@minoris.se>
Signed-off-by: Kent Gustavsson <kent@minoris.se>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add ADC5_AMUX_THM2_100K_PU and ADC5_AMUX_THM4_100K_PU to the list of
rev2 ADC channels.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After finding a reasonable gain, the function converts the configured
gain to a gain configuration option selector enum max9611_csa_gain.
Make the conversion clearly visible by using an explicit cast. This
also avoids a warning seen with clang:
drivers/iio/adc/max9611.c:292:16: warning: implicit conversion from
enumeration type 'enum max9611_conf_ids' to different enumeration
type 'enum max9611_csa_gain' [-Wenum-conversion]
*csa_gain = gain_selectors[i];
~ ^~~~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for QCOM SPMI PMIC5 family
of ADC driver that supports hardware based offset and
gain compensation. The ADC peripheral can measure both
voltage and current channels whose input signal is
connected to the PMIC ADC AMUX.
The register set and configuration has been refreshed
compared to the prior QCOM PMIC ADC family. Register
ADC5 as part of the IIO framework.
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enabling the Interrupts before registering the irq handler is a bad
idea. This patch corrects the same for XADC driver.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch avoids getting irq number in xadc_remove function. Instead
store 'irq' in xadc struct and use xadc->irq wherever needed.
This patch also resolves a warning reported by coverity where it asks to
check return value of platform_get_irq() for any errors in xadc_remove.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch limits the xadc pcap clock frequency value to be less than
200MHz. This fixes the issue when zynq is booted at higher frequency
values, pcap crosses the maximum limit of 200MHz(Fmax) as it is derived
from IOPLL.
If this limit is crossed it is required to alter the WEDGE and REDGE
bits of XADC_CFG register to make timings better in the interface. So to
avoid alteration of these bits every time, the pcap value should not
cross the Fmax limit.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds check for return values from clock related functions.
This was reported by static code analysis tool.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
wait_for_completion_timeout returns unsigned long not int so an appropriate
variable is declared and the assignment and check fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SAR ADC on Meson8m2 behaves identical to the one found in the
Meson8b SoCs. Add a separate compatible string because the temperature
sensor logic (not supported yet) differs between Meson8 and Meson8m2
(however, it's the same for Meson8b and Meson8m2).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This modifies the TI ADS7950 A/DC driver to allow the simultaneous use
of both the triggered buffer and reading channels directly (via in-
kernel API or sysfs).
The use case for this is on LEGO MINDSTORMS EV3. Two of the voltage
channels are used in-kernel by a power supply driver, which reads the
values using iio_read_channel_processed(). These channels are only read
at a slow rate (<= 1Hz). However, we want to be able to read 12 other
channels at the same time using the triggered buffer at a high rate (>=
100Hz).
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This updates the ti-ads7950.c file to use SPDX-License-Identifier
instead of more verbose license text.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This code is problematic because we're supposed to be writing an int but
we instead write to only the high 16 bits. This doesn't work on big
endian systems, and there is a potential that the bottom 16 bits are
used without being initialized.
Fixes: 23ec2774f1 ("iio: adc: at91-sama5d2_adc: add support for position and pressure channels")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch removes dead code from xadc_zynq_setup. The condition
"if (tck_rate > XADC_ZYNQ_TCK_RATE_MAX)" cannot be true at any point of
time. There is also an incompatible parameter used in the code.
This patch fixes the same reported by coverity.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On a system with parasitic capacitance it turned out that DOUT is not ready
after 100 ns after PD_SCK has raised. A measurement showed almost 1000 ns
until DOUT has reached its correct value.
With this patch its now possible to wait until data is ready.
The wait time should not be higher than the maximum PD_SCK high time which
is corresponding to the datasheet 50000 ns.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop call to of_match_device, which is subsumed by the subsequent
call to of_device_get_match_data. The code becomes simpler, and a
temporary variable can be dropped.
The semantic match that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
local idexpression match;
identifier i;
expression x, dev, e, e1;
@@
- match@i = of_match_device(x, dev);
- if (match) e = of_device_get_match_data(dev);
- else e = e1;
+ e = of_device_get_match_data(dev);
+ if (!e) e = e1;
@@
identifier r.i;
@@
- const struct of_device_id *i;
... when != i
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the buffer is enabled for ina2xx driver, a dedicated kthread is
invoked to capture mesurement data. When the buffer is disabled, the
kthread is stopped.
However if the kthread gets register access errors, it immediately exits
and when the malfunctional buffer is disabled, the stale task_struct
pointer is accessed as there is no kthread to be stopped.
A similar issue in the usbip driver is prevented by kthread_get_run and
kthread_stop_put helpers by increasing usage count of the task_struct.
This change applies the same solution.
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Fixes: c43a102e67 ("iio: ina2xx: add support for TI INA2xx Power Monitors")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Spreadtrum SC27XX PMICs ADC controller contains 32 channels,
which is used to sample voltages with 12 bits conversion.
[Baolin Wang did lots of improvements]
Signed-off-by: Freeman Liu <freeman.liu@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The usual mixed bunch. Particular good to see is the generic
touch screen driver. Will be interesting to see if this works
for other ADCs without major changes.
Core features
* Channel types
- New position relative channel type primarily for touch screen
sensors to feed the generic touchscreen driver.
New device support
* ad5586
- Add support for the AD5311R DAC.
* Generic touch screen driver as an IIO consumer.
- Note this is in input, but due to dependencies is coming through
the IIO tree.
- Specific support for this added to the at91-sama5d2 ADC.
- Various necessary DT bindings added.
Staging Drops
* ADIS16060 gyro
- A device with a very odd interface that was never cleanly supported.
It's now very difficult to get, so unlikely it'll ever be fixed up.
Cleanups and minor features and fixes
* core
- Fix y2038 timestamp issues now the core support is in place.
* 104-quad-8
- Provide some defines for magic numbers to help readability.
- Fix an off by one error in register selection
* ad7606
- Put in a missing function parameter name in a prototype.
* adis16023
- Use generic sign_extend function rather than local version.
* adis16240
- Use generic sign_extend funciton rather than local version.
* at91-sama5d2
- Drop dependency on HAS_DMA now this is handled elsewhere. Will
improve build test coverage.
- Add oversampling ratio control. Note there is a minor ABI change
here to increase the apparent depth to 14 bits so as to allow
for transparent provision of different oversampling ratios that
drop the actual bit depth to 13 or 12 bits.
* hx711
- Add a MAINTAINERS entry for this device.
* inv_mpu6050
- Replace the timestamp fifo 'special' code with generic timestamp
handling.
- Switch to using local store of timestamp divider rather than rate
as that is more helpful for accurate time measurement.
- Fix an unaligned access that didn't seem to be causing any trouble.
- Use the fifo overflow bit to track the overflow status rather than
a software counter.
- New timestamping mechanism to deal with missed sample interrupts.
* stm32-adc
- Drop HAS_DMA build dependency.
* sun4i-gpadc
- Select REGMAP_IRQ a very rarely hit build issue fix.
-----BEGIN PGP SIGNATURE-----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=SvKj
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.19a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of IIO new device support, features and cleanups in the 4.19 cycle
The usual mixed bunch. Particular good to see is the generic
touch screen driver. Will be interesting to see if this works
for other ADCs without major changes.
Core features
* Channel types
- New position relative channel type primarily for touch screen
sensors to feed the generic touchscreen driver.
New device support
* ad5586
- Add support for the AD5311R DAC.
* Generic touch screen driver as an IIO consumer.
- Note this is in input, but due to dependencies is coming through
the IIO tree.
- Specific support for this added to the at91-sama5d2 ADC.
- Various necessary DT bindings added.
Staging Drops
* ADIS16060 gyro
- A device with a very odd interface that was never cleanly supported.
It's now very difficult to get, so unlikely it'll ever be fixed up.
Cleanups and minor features and fixes
* core
- Fix y2038 timestamp issues now the core support is in place.
* 104-quad-8
- Provide some defines for magic numbers to help readability.
- Fix an off by one error in register selection
* ad7606
- Put in a missing function parameter name in a prototype.
* adis16023
- Use generic sign_extend function rather than local version.
* adis16240
- Use generic sign_extend funciton rather than local version.
* at91-sama5d2
- Drop dependency on HAS_DMA now this is handled elsewhere. Will
improve build test coverage.
- Add oversampling ratio control. Note there is a minor ABI change
here to increase the apparent depth to 14 bits so as to allow
for transparent provision of different oversampling ratios that
drop the actual bit depth to 13 or 12 bits.
* hx711
- Add a MAINTAINERS entry for this device.
* inv_mpu6050
- Replace the timestamp fifo 'special' code with generic timestamp
handling.
- Switch to using local store of timestamp divider rather than rate
as that is more helpful for accurate time measurement.
- Fix an unaligned access that didn't seem to be causing any trouble.
- Use the fifo overflow bit to track the overflow status rather than
a software counter.
- New timestamping mechanism to deal with missed sample interrupts.
* stm32-adc
- Drop HAS_DMA build dependency.
* sun4i-gpadc
- Select REGMAP_IRQ a very rarely hit build issue fix.
This implements oversampling support for the SAMA5d2 ADC device.
Enabling oversampling : OSR can improve resolution from 12 bits to
13 or 14 bits.
Changing the channel specification to have 14 bits, and we shift the value
1 bit to the left if we have oversampling for just one extra bit, and two
bits to the left if we have no oversampling (old support).
From this commit on, the converted values for all the voltage channels
change to 14 bits real data, with most insignificant two bits always zero
if oversampling is not enabled.
sysfs object oversampling_ratio has been enabled and
oversampling_ratio_available will list possible values (1 or 4 or 16) having
1 as default (no oversampling, 1 sample for each conversion).
Special care was required for the triggered buffer scenario (+ DMA), to
adjust the values accordingly.
Touchscreen measurements supported by this driver are not affected by
oversampling, they are still on 12 bits (scale handing is already included
in the driver).
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This implements the support for position and pressure for the included
touchscreen support in the SAMA5D2 SOC ADC block.
Two position channels are added and one for pressure.
They can be read in raw format, or through a buffer.
A normal use case is for a consumer driver to register a callback buffer
for these channels.
When the touchscreen channels are in the active scan mask,
the driver will start the touchscreen sampling and push the data to the
buffer.
Some parts of this patch are based on initial original work by
Mohamed Jamsheeth Hajanajubudeen and Bandaru Venkateswara Swamy
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We can't call regmap_irq_get_virq() unless the regmap-irq support
is enabled:
drivers/iio/adc/sun4i-gpadc-iio.o: In function `sun4i_irq_init':
sun4i-gpadc-iio.c:(.text+0x59c): undefined reference to `regmap_irq_get_virq'
I came across this in a randconfig build now, but I guess this is
a much older problem that I simply never hit before because regmap_irq
is usually enabled by one of the other drivers that need it.
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging and IIO driver update for 4.18-rc1.
It was delayed as I wanted to make sure the final driver deletions did
not cause any major merge issues, and all now looks good.
There are a lot of patches here, just over 1000. The diffstat summary
shows the major changes here:
1007 files changed, 16828 insertions(+), 227770 deletions(-)
Because of this, we might be close to shrinking the overall kernel
source code size for two releases in a row.
There was loads of work in this release cycle, primarily:
- tons of ks7010 driver cleanups
- lots of mt7621 driver fixes and cleanups
- most driver cleanups
- wilc1000 fixes and cleanups
- lots and lots of IIO driver cleanups and new additions
- debugfs cleanups for all staging drivers
- lots of other staging driver cleanups and fixes, the shortlog
has the full details.
but the big user-visable things here are the removal of 3 chunks of
code:
- ncpfs and ipx were removed on schedule, no one has cared about
this code since it moved to staging last year, and if it needs
to come back, it can be reverted.
- lustre file system is removed. I've ranted at the lustre
developers about once a year for the past 5 years, with no
real forward progress at all to clean things up and get the
code into the "real" part of the kernel. Given that the
lustre developers continue to work on an external tree and try
to port those changes to the in-kernel tree every once in a
while, this whole thing really really is not working out at
all. So I'm deleting it so that the developers can spend the
time working in their out-of-tree location and get things
cleaned up properly to get merged into the tree correctly at a
later date.
Because of these file removals, you will have merge issues on some of
these files (2 in the ipx code, 1 in the ncpfs code, and 1 in the
atomisp driver). Just delete those files, it's a simple merge :)
All of this has been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxvjGQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymoEwCbBYnyUl3cwCszIJ3L3/zvUWpmqIgAn1DDsAim
dM4lmKg6HX/JBSV4GAN0
=zdta
-----END PGP SIGNATURE-----
Merge tag 'staging-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big staging and IIO driver update for 4.18-rc1.
It was delayed as I wanted to make sure the final driver deletions did
not cause any major merge issues, and all now looks good.
There are a lot of patches here, just over 1000. The diffstat summary
shows the major changes here:
1007 files changed, 16828 insertions(+), 227770 deletions(-)
Because of this, we might be close to shrinking the overall kernel
source code size for two releases in a row.
There was loads of work in this release cycle, primarily:
- tons of ks7010 driver cleanups
- lots of mt7621 driver fixes and cleanups
- most driver cleanups
- wilc1000 fixes and cleanups
- lots and lots of IIO driver cleanups and new additions
- debugfs cleanups for all staging drivers
- lots of other staging driver cleanups and fixes, the shortlog has
the full details.
but the big user-visable things here are the removal of 3 chunks of
code:
- ncpfs and ipx were removed on schedule, no one has cared about this
code since it moved to staging last year, and if it needs to come
back, it can be reverted.
- lustre file system is removed.
I've ranted at the lustre developers about once a year for the past
5 years, with no real forward progress at all to clean things up
and get the code into the "real" part of the kernel.
Given that the lustre developers continue to work on an external
tree and try to port those changes to the in-kernel tree every once
in a while, this whole thing really really is not working out at
all. So I'm deleting it so that the developers can spend the time
working in their out-of-tree location and get things cleaned up
properly to get merged into the tree correctly at a later date.
Because of these file removals, you will have merge issues on some of
these files (2 in the ipx code, 1 in the ncpfs code, and 1 in the
atomisp driver). Just delete those files, it's a simple merge :)
All of this has been in linux-next for a while with no reported
problems"
* tag 'staging-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1011 commits)
staging: ipx: delete it from the tree
ncpfs: remove uapi .h files
ncpfs: remove Documentation
ncpfs: remove compat functionality
staging: ncpfs: delete it
staging: lustre: delete the filesystem from the tree.
staging: vc04_services: no need to save the log debufs dentries
staging: vc04_services: vchiq_debugfs_log_entry can be a void *
staging: vc04_services: remove struct vchiq_debugfs_info
staging: vc04_services: move client dbg directory into static variable
staging: vc04_services: remove odd vchiq_debugfs_top() wrapper
staging: vc04_services: no need to check debugfs return values
staging: mt7621-gpio: reorder includes alphabetically
staging: mt7621-gpio: change gc_map to don't use pointers
staging: mt7621-gpio: use GPIOF_DIR_OUT and GPIOF_DIR_IN macros instead of custom values
staging: mt7621-gpio: change 'to_mediatek_gpio' to make just a one line return
staging: mt7621-gpio: dt-bindings: update documentation for #interrupt-cells property
staging: mt7621-gpio: update #interrupt-cells for the gpio node
staging: mt7621-gpio: dt-bindings: complete documentation for the gpio
staging: mt7621-dts: add missing properties to gpio node
...
Trivial fix to spelling mistake in module description text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix the following sparse warnings:
CHECK drivers/iio/adc/stm32-dfsdm-adc.c
symbol 'stm32_dfsdm_get_buff_cb' was not declared. Should it be static?
symbol 'stm32_dfsdm_release_buff_cb' was not declared. Should it be static?
BTW, move interrupt.h to sort headers alphabetically.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for DFSDM (Digital Filter For Sigma Delta Modulators)
to STM32MP1. This variant is close to STM32H7 DFSDM, it implements
6 filter instances. Registers map is also increased.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver. The end is in sight so hopefully we'll get that one out of
staging very soon!
New device support
* AD5686
- Support AD5685R (was wrongly present as AD5685)
- Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
SPI DACs with various precisions.
- Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
- Support current sensing usings a shunt resistor.
- Support simple voltage dividers.
- support simple current sense amplifiers.
* TI dac5571
- New driver and device bindings supporting:
dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
dac5573, dac6573 and dac7573
* Meson-adc
- Support for Meson AXG with DT bindings.
* mpu6050
- Support the mpu9255 which only requires additional WHOAMI entry and
compatible string.
* st_lsm6dsx
- Support for lsm330dlc combinded accelerometer and gyro sensors with
DT bindings.
* stm32_adc
- Add support for STM32MP1 with bindings.
Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.
New features:
* ABI docs
- Add core ABI docs for angle channels.
* inv_mpu6050
- Provide support for the full range of interrupts the device
supports.
* st_accel
- Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
- Provide a multiple gpio get function.
Cleanups / Minor fixes
* core
- Use new nested structure support to improve kernel-doc.
* ad2s1200
- Use be16_to_cpup instead of opencoding.
* ad5686
- Indentation tidy up.
- Switch to SPDX
- Refactor to allow various numbers of channels.
- Refactor to separate core and SPI specific support, prior to
addition of i2c equivalent devices.
* ad7606
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* ad7746
- Replace opencoded byte swapped i2c calls with _swapped variants.
- White space and line break readability improvements.
- Reorder includes and variable declarations where appropriate.
* ad7791
- Changes to the AD ADC library used by this driver took in the
sampling frequency. This lead to be the wrong path being the one
tied to the resulting attribute, so it didn't work, and a warning
to be printed.
* ad7780
- Remove apparent support for sampling frequency control on devices
that don't support changing the sampling attributes.
* ade7854
- Fix a read of the wrong number of bits.
- Improve error handling on i2c read/write errors.
- Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
- Improve meaning inherent in some macro names by adding units etc
where relevant.
- Adjust comments to improve detail and drop the irrelevant.
- Rename register address definitions definitions to add a _REG
postfix, clearly separating them from field definitions. Reorganize
the definitions to group register address and fields.
- Use sign_extend32 rather than open coding.
- Reverse Xmas tree ordering where appropriate and align function args.
- Remove unused headers.
- Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
- Indent field definitions to visually separate them from
register address definitions.
- Use reverse xmas tree ordering where appropriate.
- Add some whitespace where it will help readability.
- Drop some unused headers.
- Use GENMASK where appropriate.
* ad2s1200
- Drop unnecessary includes and reorder alphabetically.
- Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
- Use msleep instead of usleep_range where the precise value doesn't
matter and the delays are long.
* bcm150
- Drop transaction splitting as core now handles it.
* cros_ec
- Move the shared header to the include/iio/common directory.
This brings it inline with the other multiple type devices.
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* hid-sensors
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* inv_mpu6050
- Clear out a second function definition for the same function.
- Don't flush fifo when the iio buffer is full but just drop excess
data.
- Tidy up set_power_itg and ensure it is used in the right places.
- Use set_power_itg rather than opencoding it again in the i2c mux
control.
- Make sure error paths disable the power if undoing power on.
- Used managed devm_ functions during probe. Delete remove function.
- Refactor to pull raw data read out of read_raw function.
- Simplify data reading error paths.
- Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
- Fix a potential deadlock due to varying lock ordering.
- Fix an issue where first sample from gyro after enabling is unstable
by dropping the first sample.
- Fix an issue where the user_ctrl register is incorrectly overwritten.
- Tidy up some grammar and spelling minor issus.
* mcp320x
- Use vendor compatible strings.
* mcp4018
- Switch to using i2c .probe_new.
* mcp4351
- switch to using i2c .probe_new.
* meson-adc
- rework handing on common ADC platform data so it can be shared
across multiple families of SoCs.
* sca3000
- Fix an error handling path if the ring configure fails.
* st_lsm6dsx
- Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
- Style fixes and cleanups.
- Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
- Drop some unnecessary function calls, unused variables and
unnecessary local variables.
- Fix wrong interrupt type.
- Avoid unnecessary double clear of interrupt.
- Simplify proximity calibration call which did various things
unrelated to actually calibrating.
- Separate control of the proximity and ALS interrupts.
- Improve consistency of logging.
- Separate ALS and proximity persistence settings as they have
separate hardware controls.
- Tidy up variable ordering.
- Add Brian to copyright notice given consider work on this driver.
- Take advantage of hardware support for I2C address auto increment.
- Combine individuaal enable and period attributes for the two
directions on the threshold events into a single value as the
hardware doesn't separate them.
- Move integration_time* attributes from light channel to
intensity value as they effect the intensity readings directly
and the light reading only indirectly. Hence this better
reflects reality. Also move the calibscale_available.
- Avoid returning an error in the IRQ handler.
- Hard code the reg value in _clear_interrupts as it only takes
one value in the code. Result is the function has little
purpose so opencode the two remaining i2c_smbus_write_byte
calls.
- Drop some unnecessary checking of the chip status register.
- Tidy up return path in _write_interrupt_config.
- Tidy up the ID verification code.
- Move the power and diode settings defines into the header as these
are needed for platform data configuration.
- Various renames and comment cleanups for consistency and clarity.
- Use actual device defaults for default startup settings.
- SPDX
- Add some range sanity checking to sysfs attribute writes.
- Don't provide event interfaces if the interrupt line isn't available.
- Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
string.
- Fix the integration time and lux equations.
- Make device IDs explicit index values in the device_channel_config array.
-----BEGIN PGP SIGNATURE-----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=egCX
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.18a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st round of IIO new device support, features and cleanup for the 4.18 cycle
A nice mix this time of excellent cleanups (many to send drivers
speeding toward staging graduations) and new drivers / device support.
A good part of this is Brian Masney's never ending task on the tsl2x7x
driver. The end is in sight so hopefully we'll get that one out of
staging very soon!
New device support
* AD5686
- Support AD5685R (was wrongly present as AD5685)
- Support AD5672R, AD5676, AD5676, AD5684R and AD5686R 4 and 8 channel
SPI DACs with various precisions.
- Support AD5671R, AD5675R, AD5694, AD5694R, AD5695R, AD5696 and AD5696R
I2C DACs with various percisions and numbers of channels.
* Analog front end rescale driver - New driver.
- Support current sensing usings a shunt resistor.
- Support simple voltage dividers.
- support simple current sense amplifiers.
* TI dac5571
- New driver and device bindings supporting:
dac5571, dac6571, dac7571, dac5574, dac6574, dac7574,
dac5573, dac6573 and dac7573
* Meson-adc
- Support for Meson AXG with DT bindings.
* mpu6050
- Support the mpu9255 which only requires additional WHOAMI entry and
compatible string.
* st_lsm6dsx
- Support for lsm330dlc combinded accelerometer and gyro sensors with
DT bindings.
* stm32_adc
- Add support for STM32MP1 with bindings.
Staging graduations
* adis16201 after some excelent cleanup by Himanshu Jha.
* adis16029 after some excelent cleanup by Shreeya Patel.
New features:
* ABI docs
- Add core ABI docs for angle channels.
* inv_mpu6050
- Provide support for the full range of interrupts the device
supports.
* st_accel
- Add SMO8840 ACPI ID seen in the wild on some Lenovo machines.
* stx104
- Provide a multiple gpio get function.
Cleanups / Minor fixes
* core
- Use new nested structure support to improve kernel-doc.
* ad2s1200
- Use be16_to_cpup instead of opencoding.
* ad5686
- Indentation tidy up.
- Switch to SPDX
- Refactor to allow various numbers of channels.
- Refactor to separate core and SPI specific support, prior to
addition of i2c equivalent devices.
* ad7606
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* ad7746
- Replace opencoded byte swapped i2c calls with _swapped variants.
- White space and line break readability improvements.
- Reorder includes and variable declarations where appropriate.
* ad7791
- Changes to the AD ADC library used by this driver took in the
sampling frequency. This lead to be the wrong path being the one
tied to the resulting attribute, so it didn't work, and a warning
to be printed.
* ad7780
- Remove apparent support for sampling frequency control on devices
that don't support changing the sampling attributes.
* ade7854
- Fix a read of the wrong number of bits.
- Improve error handling on i2c read/write errors.
- Rework i2c and spi code to reduce duplication.
* adis16201 (staging)
- Improve meaning inherent in some macro names by adding units etc
where relevant.
- Adjust comments to improve detail and drop the irrelevant.
- Rename register address definitions definitions to add a _REG
postfix, clearly separating them from field definitions. Reorganize
the definitions to group register address and fields.
- Use sign_extend32 rather than open coding.
- Reverse Xmas tree ordering where appropriate and align function args.
- Remove unused headers.
- Use GENMASK where appropriate instead of open coding.
* adis16209 (staging)
- Indent field definitions to visually separate them from
register address definitions.
- Use reverse xmas tree ordering where appropriate.
- Add some whitespace where it will help readability.
- Drop some unused headers.
- Use GENMASK where appropriate.
* ad2s1200
- Drop unnecessary includes and reorder alphabetically.
- Reverse xmas tree and blank line cleanups.
* atlas-ph-sensor
- Use msleep instead of usleep_range where the precise value doesn't
matter and the delays are long.
* bcm150
- Drop transaction splitting as core now handles it.
* cros_ec
- Move the shared header to the include/iio/common directory.
This brings it inline with the other multiple type devices.
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* hid-sensors
- Use drvdata directly from device rather than boucing via the
platform_device structure.
* inv_mpu6050
- Clear out a second function definition for the same function.
- Don't flush fifo when the iio buffer is full but just drop excess
data.
- Tidy up set_power_itg and ensure it is used in the right places.
- Use set_power_itg rather than opencoding it again in the i2c mux
control.
- Make sure error paths disable the power if undoing power on.
- Used managed devm_ functions during probe. Delete remove function.
- Refactor to pull raw data read out of read_raw function.
- Simplify data reading error paths.
- Only enable the i2c mux for chips with the i2c aux bus (not icm20608)
- Fix a potential deadlock due to varying lock ordering.
- Fix an issue where first sample from gyro after enabling is unstable
by dropping the first sample.
- Fix an issue where the user_ctrl register is incorrectly overwritten.
- Tidy up some grammar and spelling minor issus.
* mcp320x
- Use vendor compatible strings.
* mcp4018
- Switch to using i2c .probe_new.
* mcp4351
- switch to using i2c .probe_new.
* meson-adc
- rework handing on common ADC platform data so it can be shared
across multiple families of SoCs.
* sca3000
- Fix an error handling path if the ring configure fails.
* st_lsm6dsx
- Fix a wrong fifo threshold mask (no actual effect)
* stm32-dfsdm
- Style fixes and cleanups.
- Check filter ID is in range and check spi-max-frequency.
* tsl2x7x (staging)
- Drop some unnecessary function calls, unused variables and
unnecessary local variables.
- Fix wrong interrupt type.
- Avoid unnecessary double clear of interrupt.
- Simplify proximity calibration call which did various things
unrelated to actually calibrating.
- Separate control of the proximity and ALS interrupts.
- Improve consistency of logging.
- Separate ALS and proximity persistence settings as they have
separate hardware controls.
- Tidy up variable ordering.
- Add Brian to copyright notice given consider work on this driver.
- Take advantage of hardware support for I2C address auto increment.
- Combine individuaal enable and period attributes for the two
directions on the threshold events into a single value as the
hardware doesn't separate them.
- Move integration_time* attributes from light channel to
intensity value as they effect the intensity readings directly
and the light reading only indirectly. Hence this better
reflects reality. Also move the calibscale_available.
- Avoid returning an error in the IRQ handler.
- Hard code the reg value in _clear_interrupts as it only takes
one value in the code. Result is the function has little
purpose so opencode the two remaining i2c_smbus_write_byte
calls.
- Drop some unnecessary checking of the chip status register.
- Tidy up return path in _write_interrupt_config.
- Tidy up the ID verification code.
- Move the power and diode settings defines into the header as these
are needed for platform data configuration.
- Various renames and comment cleanups for consistency and clarity.
- Use actual device defaults for default startup settings.
- SPDX
- Add some range sanity checking to sysfs attribute writes.
- Don't provide event interfaces if the interrupt line isn't available.
- Use IIO_CONST_ATTR macro for calibscale_available as it's a constant
string.
- Fix the integration time and lux equations.
- Make device IDs explicit index values in the device_channel_config array.
* core
- fix up some issues with overflow etc around wrong types
for some fo the kfifo handling functions. Seems unlikely
this would be triggered in reality but the fixes are simple
so let's tidy them up. Second patch deals with checking
the userspace value passed for length for potential overflow.
* ad7793
- Catch up with changes to the ad_sigma_delta core and use
read_raw / write_raw iwth IIO_CHAN_INFO_SAMP_FEW to handle
sampling frequency control.
* at91-sama5d2
- Channel config for differential channels was completely broken.
- Missing Kconfig dependency for buffer support.
* hid-sensor
- Fix an issue with powering up after resume due to wrong reference
counting.
* stm32-dfsdm
- Fix an issue with second writes of the oversampling settings
failing.
- Fix an issue with the sample rate being set to half of requested
value when particular clock source is used.
-----BEGIN PGP SIGNATURE-----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=1bkD
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.17a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.17 cycle.
* core
- fix up some issues with overflow etc around wrong types
for some fo the kfifo handling functions. Seems unlikely
this would be triggered in reality but the fixes are simple
so let's tidy them up. Second patch deals with checking
the userspace value passed for length for potential overflow.
* ad7793
- Catch up with changes to the ad_sigma_delta core and use
read_raw / write_raw iwth IIO_CHAN_INFO_SAMP_FEW to handle
sampling frequency control.
* at91-sama5d2
- Channel config for differential channels was completely broken.
- Missing Kconfig dependency for buffer support.
* hid-sensor
- Fix an issue with powering up after resume due to wrong reference
counting.
* stm32-dfsdm
- Fix an issue with second writes of the oversampling settings
failing.
- Fix an issue with the sample rate being set to half of requested
value when particular clock source is used.
Add support for STM32MP1 ADC. It's quite similar to STM32H7 ADC.
Introduce new compatible to handle variants of this hardware such as
vregready flag, trigger list, interrupts, clock rate.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
spi-max-frequency is requested for SPI master mode (only), to tune output
clock. It may happen requested frequency isn't reachable.
Add explicit check, so probe fails with error in this case. Otherwise,
output clock may simply be silently turned off (conversions fail).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
reg property should be checked against number of available filters.
BTW, dfsdm->num_fls wasn't used. But it can be used for this purpose.
This prevents using data out of allocated dfsdm->fl_list array.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Misc fixes & style improvements:
- checkpatch warns about line over 80 characters.
- remove extra spaces and a blank line (e.g. checkpatch --strict)
- remove bad error message always printed in probe routine.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need to select the buffer code, otherwise we get build errors
with undefined functions on the trigger and buffer,
if we select just IIO and then AT91_SAMA5D2_ADC from menuconfig
This adds a Kconfig 'select' statement like other ADC
drivers have it already.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When iterating through the channels, the index in the array is not the
scan index. Added an xlate function to translate to the proper index.
The result of the bug is that the channel array is indexed with a wrong index,
thus instead of the proper channel, we access invalid memory, which may
lead to invalid results and/or corruption.
This will be used also for devicetree channel xlate.
Fixes: 5e1a1da0f ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Fixes: 073c66201 ("iio: adc: at91-sama5d2_adc: add support for DMA")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of
depending on it. This is merged with the same pattern
for all the ISA drivers and some other Kconfig cleanups
related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of
this SoC from the ARM tree.
- Move the documentation over to driver-api to conform with
the rest of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h>
that we want to get rid of.
- Managed to remove VLA allocation from two drivers pending
more fixes in this area for the next merge window.
- Misc janitorial fixes.
-----BEGIN PGP SIGNATURE-----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=C5t5
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
Add the SAR ADC driver for the Amlogic Meson-AXG SoC.
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Extract and promote common adc platform data into a new structure,
to make it better share the info between several SoCs,
this will avoid duplicating the code all over the place,
Save a few memory and make the code more maintainable.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Gregory CLEMENT