Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
There maybe a race when using dmaengine_terminate_all(). The predisable
routine may call iio_triggered_buffer_predisable() prior to a pending DMA
callback.
Adopt dmaengine_terminate_sync() to ensure there's no pending DMA request
before calling iio_triggered_buffer_predisable().
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some chips have a fifo overflow bit issue where the bit is always
set. The result is that every data is dropped.
Change fifo overflow management by checking fifo count against
a maximum value.
Add fifo size in chip hardware set of values.
Fixes: f5057e7b2d ("iio: imu: inv_mpu6050: better fifo overflow handling")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The measured time value in the driver is limited to the maximum distance
which can be read by the sensor. This limitation was wrong and is fixed
by this patch.
It also takes into account that we are supporting a variety of sensors
today and that the recently added sensors have a higher maximum
distance range.
Changes in v2:
- Added a Tested-by
Suggested-by: Zbyněk Kocur <zbynek.kocur@fel.cvut.cz>
Tested-by: Zbyněk Kocur <zbynek.kocur@fel.cvut.cz>
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc:<Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It could happen that either `val` or `val2` [provided from userspace] is
negative. In that case the computed frequency could get a weird value.
Fix this by checking that neither of the 2 variables is negative, and check
that the computed result is not-zero.
Fixes: e4f9593901 ("iio: imu: adis16480 switch sampling frequency attr to core support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
-----BEGIN PGP SIGNATURE-----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=s9EA
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.4 cycle.
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: Fix an undefied reference error in noa1305_probe
iio: light: opt3001: fix mutex unlock race
iio: adc: ad799x: fix probe error handling
iio: light: add missing vcnl4040 of_compatible
iio: light: fix vcnl4000 devicetree hooks
iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
iio: adc: axp288: Override TS pin bias current for some models
iio: imu: adis16400: fix memory leak
iio: imu: adis16400: release allocated memory on failure
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
iio: adc: stm32-adc: move registers definitions
iio: accel: adxl372: Perform a reset at start up
iio: accel: adxl372: Fix push to buffers lost samples
iio: accel: adxl372: Fix/remove limitation for FIFO samples
iio: adc: hx711: fix bug in sampling of data
iio: fix center temperature of bmc150-accel-core
iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
iio: adc: meson_saradc: Fix memory allocation order
I hit the following error when compile the kernel.
drivers/iio/light/noa1305.o: In function `noa1305_probe':
noa1305.c:(.text+0x65): undefined reference to `__devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an end-of-conversion interrupt is received after performing a
single-shot reading of the light sensor, the driver was waking up the
result ready queue before checking opt->ok_to_ignore_lock to determine
if it should unlock the mutex. The problem occurred in the case where
the other thread woke up and changed the value of opt->ok_to_ignore_lock
to false prior to the interrupt thread performing its read of the
variable. In this case, the mutex would be unlocked twice.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Fixes: 94a9b7b180 ("iio: light: add support for TI's opt3001 light sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe
and reset alert status on probe") the error path is wrong since it
leaves the vref regulator on. Fix this by disabling both regulators.
Fixes: 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040
proximity and light sensor") added the support for the vcnl4040 but
forgot to add the of_compatible. Fix this by adding it now.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 5a441aade5 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
the of_match_table is supported but the data shouldn't be a string.
Instead it shall be one of 'enum vcnl4000_device_ids'. Also the matching
logic for the vcnl4020 was wrong. Since the data retrieve mechanism is
still based on the i2c_device_id no failures did appeared till now.
Fixes: ebd457d559 ("iio: light: vcnl4000 add devicetree hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c controller available in st_lsm6dsx series performs i2c slave
configuration using accel clock as trigger.
st_lsm6dsx_shub_wait_complete routine is used to wait the controller has
carried out the requested configuration. However if the accel sensor is not
enabled we should not use its configured odr to estimate a proper timeout
Fixes: c91c1c844e ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.
In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).
Fixes: 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode_burst, if adis->buffer allocation fails release
the adis->xfer.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
request instead. It's then automatically cleared by DMA read. But the
handler gets called due to status bit is temporarily set (IRQ triggered
by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need to perform a reset a start up to make sure that the chip is in a
consistent state. This reset also disables all the interrupts which
should only be enabled together with the iio buffer. Not doing this, was
sometimes causing unwanted interrupts to trigger.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
One in two sample sets was lost by multiplying fifo_set_size with
sizeof(u16). Also, the double number of available samples were pushed to
the iio buffers.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, the driver sets the FIFO_SAMPLES register with the number of
sample sets (maximum of 170 for 3 axis data, 256 for 2-axis and 512 for
single axis). However, the FIFO_SAMPLES register should store the number
of samples, regardless of how the FIFO format is configured.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce38e ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes: c3b2fdd0ea ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging/iio driver update for 5.4-rc1.
Lots of churn here, with a few driver/filesystems moving out of staging
finally:
- erofs moved out of staging
- greybus core code moved out of staging
Along with that, a new filesytem has been added:
- extfat
to provide support for those devices requiring that filesystem (i.e.
transfer devices to/from windows systems or printers.)
Other than that, there a number of new IIO drivers, and lots and lots
and lots of staging driver cleanups and minor fixes as people continue
to dig into those for easy changes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIW0g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynJgwCgt22YQdsWRrOuJnZp3xpFq/ZSMWAAn0dAgFf5
SlSTI2nQhbW7jjdShrPR
=Ra09
-----END PGP SIGNATURE-----
Merge tag 'staging-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver updates from Greg KH:
"Here is the big staging/iio driver update for 5.4-rc1.
Lots of churn here, with a few driver/filesystems moving out of
staging finally:
- erofs moved out of staging
- greybus core code moved out of staging
Along with that, a new filesytem has been added:
- extfat
to provide support for those devices requiring that filesystem (i.e.
transfer devices to/from windows systems or printers)
Other than that, there a number of new IIO drivers, and lots and lots
and lots of staging driver cleanups and minor fixes as people continue
to dig into those for easy changes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (453 commits)
Staging: gasket: Use temporaries to reduce line length.
Staging: octeon: Avoid several usecases of strcpy
staging: vhciq_core: replace snprintf with scnprintf
staging: wilc1000: avoid twice IRQ handler execution for each single interrupt
staging: wilc1000: remove unused interrupt status handling code
staging: fbtft: make several arrays static const, makes object smaller
staging: rtl8188eu: make two arrays static const, makes object smaller
staging: rtl8723bs: core: Remove Macro "IS_MAC_ADDRESS_BROADCAST"
dt-bindings: anybus-controller: move to staging/ tree
staging: emxx_udc: remove local TRUE/FALSE definition
staging: wilc1000: look for rtc_clk clock
staging: dt-bindings: wilc1000: add optional rtc_clk property
staging: nvec: make use of devm_platform_ioremap_resource
staging: exfat: drop unused function parameter
Staging: exfat: Avoid use of strcpy
staging: exfat: use integer constants
staging: exfat: cleanup spacing for casts
staging: exfat: cleanup spacing for operators
staging: rtl8723bs: hal: remove redundant variable n
staging: pi433: Fix typo in documentation
...
RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware support
that was removed in 2004; one doesn't want to rush these things.
- The usual assortment of fixes, typo corrections, etc.
You'll still find a handful of annoying conflicts against other trees,
mostly tied to the last RST conversions; resolutions are straightforward
and the linux-next ones are good.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl1/J4IACgkQF0NaE2wM
flhYogf9EgYozCe8RocSq+JjJpZOSFjIGDQv+GwTjOBIdqgO9tSIaY/p0wSkYKil
jYXyMDF+Xwr8podsUep2F7akBM7j9XJ+XBGJcfOna0ypC9xoejMgWt9fU3YvaWge
dQJxIQ/iwkDlKNx6uOYgKysLUWFS0EP/nzPhqBo4bZZzhugvrR46D/nQqFNmGihd
l9yLalJtP5mC0XRUv3hpdAFFFKxdC0R3BGOel2V+slSClp0LEgpdMAuMaKydEDI3
Ch9ZpIp8fB8kqONCs9/X6083WRsDOMe28KgeGrGHo4Jla6u51QBLQjSVKttFv7xk
051yNJwDWMxgl+A4gyNLDPXM7Gd7HQ==
=v4dp
-----END PGP SIGNATURE-----
Merge tag 'docs-5.4' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It's a somewhat calmer cycle for docs this time, as the churn of the
mass RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware
support that was removed in 2004; one doesn't want to rush these
things.
- The usual assortment of fixes, typo corrections, etc"
* tag 'docs-5.4' of git://git.lwn.net/linux: (67 commits)
Documentation: kbuild: Add document about reproducible builds
docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]
Documentation: Add "earlycon=sbi" to the admin guide
doc🔒 remove reference to clever use of read-write lock
devices.txt: improve entry for comedi (char major 98)
docs: mtd: Update spi nor reference driver
doc: arm64: fix grammar dtb placed in no attributes region
Documentation: sysrq: don't recommend 'S' 'U' before 'B'
mailmap: Update email address for Quentin Perret
docs: ftrace: clarify when tracing is disabled by the trace file
docs: process: fix broken link
Documentation/arm/samsung-s3c24xx: Remove stray U+FEFF character to fix title
Documentation/arm/sa1100/assabet: Fix 'make assabet_defconfig' command
Documentation/arm/sa1100: Remove some obsolete documentation
docs/zh_CN: update Chinese howto.rst for latexdocs making
Documentation: virt: Fix broken reference to virt tree's index
docs: Fix typo on pull requests guide
kernel-doc: Allow anonymous enum
Documentation: sphinx: Don't parse socket() as identifier reference
Documentation: sphinx: Add missing comma to list of strings
...
The center temperature of the supported devices stored in the constant
BMC150_ACCEL_TEMP_CENTER_VAL is not 24 degrees but 23 degrees.
It seems that some datasheets were inconsistent on this value leading
to the error. For most usecases will only make minor difference so
not queued for stable.
Signed-off-by: Pascal Bouwmann <bouwmann@tau-tec.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not allow configuring null sensor gain since it will force to 0
device outputs
Fixes: c8d4066c7246 ("iio: imu: st_lsm6dsx: remove invalid gain value for LSM9DS1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
meson_saradc's irq handler uses priv->regmap so make sure that it is
allocated before the irq get enabled.
This also fixes crash when CONFIG_DEBUG_SHIRQ is enabled, as device
managed resources are freed in the inverted order they had been
allocated, priv->regmap was freed before the spurious fake irq that
CONFIG_DEBUG_SHIRQ adds called the handler.
Fixes: 3af109131b ("iio: adc: meson-saradc: switch from polling to interrupt mode")
Reported-by: Elie Roudninski <xademax@gmail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Elie ROUDNINSKI <xademax@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The commit 473d12f763
("iio: hid-sensor-attributes: Convert to use int_pow()")
converted to use generic int_pow() helper. Though, the generic one returns
64-bit value and, in cases when it is used as divisor, it compels 64-bit
division from compiler.
In order to fix this, introduce a temporary 32-bit variable to hold the result
of int_pow() and use it as divisor afterwards.
In couple of cases, replace int_pow() with a predefined unit factors for time
and frequency.
Fixes: 473d12f763 ("iio: hid-sensor-attributes: Convert to use int_pow()")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20190905112759.13035-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revised pull request to fix up a missing Signed-off-by and roll in
a fix in the lsm9ds1 support after I broke it when applying.
Revised again because the fix changed a hash meaning a fix
that previously followed it now had the wrong fixes tag.
A few fixes in here that could have gone a faster path but aren't quite
worth the rush for 5.3.
New device support
* ad7606
- Support the ad7606b which adds a software controlled mode alongside
the pin controlled only approach of the ad7606. Including dt-bindings.
* lsm6dsx
- Add support for the gyro and accelerometer part of the lsm9ds1 which is
a compound device also including a magnetometer (st_sensors driver).
Includes bindings and precursor rework of the driver.
Features
* ad7192
- Add support for low pass filter control.
- DT binding docs.
Cleanups and minor fixes
* MAINTAINERS
- Fix a typo in a path.
- Add entry for ad7606
* ad5380
- Fix a failure to dereference a pointer before atempting to assign the
value.
* ad7192
- Drop platform data as not used in mainline and we now have full DT bindings.
* ad7606
- YAML conversion for dt-bindings.
* adis16240
- Rework write_raw to make it more readable using GENMASK.
* adis16460
- Fix and issue with an unsigned variable holding potential negatives.
* cros_ec
- Fix missing default of calibration vector so that we get 'something'
before calibration is complete on a given axis.
* hid-sensors
- Use int_pow instead of opencoding.
* isl29501
- rename dt-binding docs to include renesas inline with other renesas parts
and general current convention.
* kxcjk1013
- Improve comments on the 'unusual' ACPI ids used to identify which sensor
is which in certain laptops.
* lsm6dsx
- Add one bit to the fifo status masks for a number of parts.
- Drop a reserved entry from the sensitivity values to tidy up interface.
- Use core conversion macro from G to m/s^2 for lsm9ds1 to make it easier
to relate to the datasheet and consistent with other parts supported.
* max1027
- Use device managed APIs to avoid manual error handling and cleanup.
* rfd77402
- Typo in Kconfig help.
* sc27xx
- Switch to polling mode from interrupts as interrupt handling typically
to slow for very short sleeps.
* st-sensors
- Fix some missing selects for regmap.
* tools
- Add a .gitignore containing the binary outputs.
-----BEGIN PGP SIGNATURE-----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=rPVR
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.4b-take3' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, cleanups and features for IIO in the 5.4 cycle
Revised pull request to fix up a missing Signed-off-by and roll in
a fix in the lsm9ds1 support after I broke it when applying.
Revised again because the fix changed a hash meaning a fix
that previously followed it now had the wrong fixes tag.
A few fixes in here that could have gone a faster path but aren't quite
worth the rush for 5.3.
New device support
* ad7606
- Support the ad7606b which adds a software controlled mode alongside
the pin controlled only approach of the ad7606. Including dt-bindings.
* lsm6dsx
- Add support for the gyro and accelerometer part of the lsm9ds1 which is
a compound device also including a magnetometer (st_sensors driver).
Includes bindings and precursor rework of the driver.
Features
* ad7192
- Add support for low pass filter control.
- DT binding docs.
Cleanups and minor fixes
* MAINTAINERS
- Fix a typo in a path.
- Add entry for ad7606
* ad5380
- Fix a failure to dereference a pointer before atempting to assign the
value.
* ad7192
- Drop platform data as not used in mainline and we now have full DT bindings.
* ad7606
- YAML conversion for dt-bindings.
* adis16240
- Rework write_raw to make it more readable using GENMASK.
* adis16460
- Fix and issue with an unsigned variable holding potential negatives.
* cros_ec
- Fix missing default of calibration vector so that we get 'something'
before calibration is complete on a given axis.
* hid-sensors
- Use int_pow instead of opencoding.
* isl29501
- rename dt-binding docs to include renesas inline with other renesas parts
and general current convention.
* kxcjk1013
- Improve comments on the 'unusual' ACPI ids used to identify which sensor
is which in certain laptops.
* lsm6dsx
- Add one bit to the fifo status masks for a number of parts.
- Drop a reserved entry from the sensitivity values to tidy up interface.
- Use core conversion macro from G to m/s^2 for lsm9ds1 to make it easier
to relate to the datasheet and consistent with other parts supported.
* max1027
- Use device managed APIs to avoid manual error handling and cleanup.
* rfd77402
- Typo in Kconfig help.
* sc27xx
- Switch to polling mode from interrupts as interrupt handling typically
to slow for very short sleeps.
* st-sensors
- Fix some missing selects for regmap.
* tools
- Add a .gitignore containing the binary outputs.
* tag 'iio-for-5.4b-take3' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (27 commits)
iio: imu: st_lsm6dsx: rely on IIO_G_TO_M_S_2 for gain definition for LSM9DS1
iio: imu: st_lsm6dsx: remove invalid gain value for LSM9DS1
iio: cros_ec: set calibscale for 3d MEMS to unit vector
iio: dac: ad5380: fix incorrect assignment to val
iio: imu: st_lsm6dsx: Fix FIFO diff mask for tagged fifo
dt-bindings: iio: imu: st_lsm6dsx: add lsm9ds1 device bindings
iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1
iio: imu: st_lsm6dsx: move register definitions to sensor_settings struct
iio: imu: st_lsm6dsx: introduce update_fifo function pointer
dt-bindings: iio: light: isl29501: Rename bindings documentation file
Kconfig: Fix the reference to the RFD77402 ToF sensor in the 'help' section
iio: st_sensors: Fix build error
dt-bindings: iio: adc: Add AD7606B ADC documentation
dt-bindings: iio: adc: Migrate AD7606 documentation to yaml
MAINTAINERS: Add Beniamin Bia for AD7606 driver
iio: adc: ad7606: Add support for AD7606B ADC
tools: iio: add .gitignore
iio: adc: sc27xx: Change to polling mode to read data
iio: hid-sensor-attributes: Convert to use int_pow()
iio: adc: max1027: Use device-managed APIs
...
Rely on IIO_G_TO_M_S_2 macro for LSM9DS1 accelerometer gain definitions
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Get rid of invalid sensitivity value for LSM9DS1 gyro sensor
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A driver for ADS1015 with more functionality is available in the iio
subsystem.
Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.
Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By default, set the calibscale vector to unit vector.
When calibrating one axis, the other axis calibrations are sent as well.
If left to 0, sensor data from uncalibrated axis are zero'ed out until
all axis are calibrated.
Fixes: ed1f2e85da ("iio: cros_ec: Add calibscale for 3d MEMS ")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently the pointer val is being incorrectly incremented
instead of the value pointed to by val. Fix this by adding
in the missing * indirection operator.
Addresses-Coverity: ("Unused value")
Fixes: c03f2c5368 ("staging:iio:dac: Add AD5380 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the latest version of datasheet the mask
for number of unread sensor data in FIFO_STATUS registers
has been extended to 10 bits
The devices involved are:
- LSM6DSO
- LSM6DSOX
- ASM330LHH
- LSM6DSR
- ISM330DHCX
Signed-off-by: mario tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The LSM9DS1's accelerometer / gyroscope unit and it's magnetometer (separately
supported in iio/magnetometer/st_magn*) are located on a separate i2c addresses
on the bus.
For the datasheet, see https://www.st.com/resource/en/datasheet/lsm9ds1.pdf
Treat it just like the LSM6* devices and, despite it's name, hook it up
to the st_lsm6dsx driver, using it's basic functionality.
accelerometer and gyroscope are not independently clocked. It runs at the gyro
frequencies if both are enabled, see chapter 7.12 of the datasheet.
We could have handled this as a single IIO device but we have split
it up to be more consistent with the other more flexible devices.
Despite supporting and testing the LSM9DS1, we call the gyro channels
iio_chan_spec struct "st_lsm6ds0_gyro_channels" because the register
description is equal. This suggests that supporting LSM6DS0 should be
trivial to do.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, the ChromeOS EC core driver has nothing related to an MFD device, so
move that driver from the MFD subsystem to the platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move some register definitions to the per-device array of struct
st_lsm6dsx_sensor_settings in order to simplify adding new sensor
devices to the driver.
Also, remove completely unused register definitions.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce update_fifo routine pointer in st_lsm6dsx_fifo_ops data
structure since we will need a different update FIFO configuration
callback adding support for lsm6ds0/lsm9ds1 imu device
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This should be RFD77402, not RFD77420.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO_ST_SENSORS_CORE select IIO_ST_SENSORS_I2C
unconditionally, if REGMAP_I2C is not set, build fails
drivers/iio/common/st_sensors/st_sensors_i2c.o: In function `st_sensors_i2c_configure':
st_sensors_i2c.c:(.text+0x58): undefined reference to `__devm_regmap_init_i2c'
This patch selects REGMAP_I2C to fix it.
IIO_ST_SENSORS_SPI is similar to SPI issue.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 062809ef77 ("iio: make st_sensors drivers use regmap")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7606B is a 16-bit ADC that supports simultaneous sampling of 8
channels. It is pin compatible to AD7606, but adds extra modes by
writing to the register map.
The AD7606B can be configured to work in software mode by setting all
oversampling pins to high. This mode is selected by default.
The oversampling ratio is configured from the OS_MODE register (address
0x08) with the addition of OS=128 and OS=256 that were not available in
hardware mode.
The device is configured to output data on a single spi channel, but this
configuration must be done right after restart. That is why the delay was
removed for devices which doesn't require it.
Moreover, in software mode, the range gpio has no longer its function.
Instead, the scale can be configured individually for each channel from
the RANGE_CH registers (address 0x03 to 0x06). Besides the already
supported ±10 V and ±5 V ranges, software mode can also accommodate the
±2.5 V range.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On Spreadtrum platform, the headphone will read one ADC channel multiple
times to identify the headphone type, and the headphone identification is
sensitive of the ADC reading time. And we found it will take longer time
to reading ADC data by using interrupt mode comparing with the polling
mode, thus we should change to polling mode to improve the efficiency
of reading data, which can identify the headphone type successfully.
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of linear approach to calculate power of 10, use generic int_pow()
which does it better.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use device-managed APIs to simplify the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Caught via static-analysis checker:
```
drivers/iio/imu/adis16460.c
152 static int adis16460_set_freq(struct iio_dev *indio_dev, int val, int val2)
153 {
154 struct adis16460 *st = iio_priv(indio_dev);
155 unsigned int t;
^^^^^^^^^^^^^^
156
157 t = val * 1000 + val2 / 1000;
158 if (t <= 0)
^^^^^^
Unsigned is not less than zero.
```
The types of `val` && `val2` are obtained from the IIO `write_raw` hook, so
userspace can provide negative values, which can cause weird behavior after
conversion to unsigned.
This patch changes the sign of variable `t` so that -EINVAL will be
returned for negative values as well.
Fixes: db6ed4d23d ("iio: imu: Add support for the ADIS16460 IMU")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jianping Liu