Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
A tab sneaked in, where it shouldn't be.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
R-Car GPIO controller provides two interfaces to set GPIO line output
signal state, and for a particular GPIO line the selected interface is
determined by OUTDTSEL bit value.
At the moment the driver supports only one of two interfaces, namely
OUTDT General Output Register is used to control the output signal.
While this selection is the default one on reset, it is not explicitly
configured on probe, thus it might be possible that kernel and userspace
consumers of a GPIO won't be able to set the wanted GPIO output signal.
Below is a simple test case to reproduce the described problem and
verify this fix in the kernel on H3 ULCB by setting non-default OUTDTSEL
configuration from a bootloader:
u-boot > mw.l 0xe6055440 0x3000 1
...
userspace > echo default-on > /sys/devices/platform/leds/leds/led5/trigger
userspace > echo default-on > /sys/devices/platform/leds/leds/led6/trigger
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change simplifies dereferences to the mediated struct device, also
it allows to limit the scope of the platform device usage to probe and
remove functions only.
Non-functional change.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO hole is present in RZ/G1C SoC. Valid GPIO pins on bank3 are in the
range GP3_0 to GP3_16 and GP3_27 to GP3_29. The GPIO pins between GP3_17
to GP3_26 are unused. Add support for handling unused GPIO's.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow gpiolib to read back the current I/O direction configuration by
implementing the .get_direction() callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqlyPEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGNa0H/RIa/StQuYu/SBwa
JRqQFmkIsx+gG+FyamJrqGzRfyjounES8PbfyaN3cCrzYgeRwMp1U/bZW6/l5tkb
OjTtrCJ6CJaa21fC/7aqn3rhejHciKyk83EinMu5WjDpsQcaF2xKr3SaPa62Ja24
fhawKq3CnUa+OUuAbicVX8yn4viUB6x8FjSN/IWfp3Cs4IBR7SGxxD7A4MET9FbQ
5OOu0al8ly9QeCggTtJyk+cApeLfexEBTbUur9gm7GcH9jhUtJSyZCZsDJx6M2yb
CwdgF4fyk58c1fuHvTFb0AdUns55ba3nicybRHHMVbDpZIG9v4/M1yJETHHf5cD7
t3rFjrY=
=+Ldf
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc5' into devel
Linux 4.16-rc5 merged into the GPIO devel branch to resolve
a nasty conflict between fixes and devel in the RCAR driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit ab82fa7da4 ("gpio: rcar: Prevent module clock disable
when wake-up is enabled"), when a GPIO is used for wakeup, the GPIO
block's module clock (if exists) is manually kept running during system
suspend, to make sure the device stays active.
However, this explicit clock handling is merely a workaround for a
failure to properly communicate wakeup information to the device core.
Instead, set the device's power.wakeup_path field, to indicate this
device is part of the wakeup path. Depending on the PM Domain's
active_wakeup configuration, the genpd core code will keep the device
enabled (and the clock running) during system suspend when needed.
This allows for the removal of all explicit clock handling code from the
driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds an implementation that saves and restores the state of
GPIO configuration on suspend and resume.
Signed-off-by: Hien Dang <hien.dang.eb@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Modify structure of the bank info to simplify a saving registers]
[Remove DEV_PM_OPS macro]
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using devm_ioremap_resource() has several advantages over devm_ioremap():
- it checks the passed resource's validity;
- it calls devm_request_mem_region() to check for the resource overlap;
- it prints an error message in case of error.
We can call devm_ioremap_resource() instead of devm_ioremap_nocache()
as ioremap() and ioremap_nocache() are implemented identically on ARM.
Doing this saves 2 LoCs and 80 bytes (AArch64 gcc 4.8.5).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the of_device_get_match_data() helper instead of open coding.
Note that the gpio-rcar driver is used with DT only, so there's always a
valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add fallback compatibility string for R-Car Gen 1, 2 and 3.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Also deprecate renesas,gpio-rcar as its name is more generic than its
implementation.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Renesas RZ/G1M (R8A7743) SoC GPIO blocks are identical to the R-Car Gen2
family. Add support for its GPIO controllers.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently gpio modules are runtime-resumed at probe time. This means the
gpio module will be active all the time (except during system suspend,
if not configured as a wake-up source).
While an R-Car Gen2 gpio module retains pins configured for output at
the requested level while put in standby mode, gpio register cannot be
accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be
called from all contexts where gpio register access is needed. Hence
move the Runtime PM handling from probe/remove time to gpio request/free
time, which is probably the best we can do.
On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during
normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6
for SD-Card CD & WP, gpio7 for keys and regulators).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[Niklas: s/gpio_to_priv(chip)/gpiochip_get_data(chip)/]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enables Runtime PM handling for interrupts.
By setting the parent_device in struct irq_chip genirq will call the
pm_runtime_get/put APIs when an IRQ is requested/freed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
R-Car Gen3's GPIO blocks are identical to Gen2's in every respect.
Based on work for the r8a7795 (R-Car H3) by Ulrich Hecht.
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Renesas R8A7792 SoC is a member of the R-Car gen2 family, add support for
its GPIO controllers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
This allows to set multiple outputs using a single register write.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The R-Car GPIO driver handles Runtime PM for requested GPIOs only.
When using a GPIO purely as an interrupt source, no Runtime PM handling
is done, and the GPIO module's clock may not be enabled.
To fix this:
- Add .irq_request_resources() and .irq_release_resources() callbacks
to handle Runtime PM when an interrupt is requested,
- Add irq_bus_lock() and sync_unlock() callbacks to handle Runtime PM
when e.g. disabling/enabling an interrupt, or configuring the
interrupt type.
Fixes: d5c3d84657 "net: phy: Avoid polling PHY with PHY_IGNORE_INTERRUPTS"
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the Renesas R-Car GPIO driver cannot find a functional clock, it
prints a warning, .e.g.
gpio_rcar ffc40000.gpio: unable to get clock
and continues, as the clock is optional, depending on the SoC type.
This warning may confuse users.
To fix this, add a flag to indicate that the clock is mandatory or
optional:
- If the clock is mandatory (on R-Car Gen2 and Gen3), a missing clock
is now treated as a fatal error,
- If the clock is optional (on R-Car Gen1), the warning is no longer
printed.
Suggested-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), Renesas R-Car SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to use platform data
anymore, hence remove platform data configuration.
Make gpio_rcar_priv.has_both_edge_trigger a boolean for consistency with
gpio_rcar_info.has_both_edge_trigger.
Move gpio_rcar_priv.irq_parent down while we're at it, to prevent gaps
on 64-bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently gpio modules are runtime-resumed at probe time. This means the
gpio module will be active all the time (except during system suspend,
if not configured as a wake-up source).
While an R-Car Gen2 gpio module retains pins configured for output at
the requested level while put in standby mode, gpio registercannot be
accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be
called from all contexts where gpio register access is needed. Hence
move the Runtime PM handling from probe/remove time to gpio request/free
time, which is probably the best we can do.
On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during
normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6
for SD-Card CD & WP, gpio7 for keys and regulators).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If an interrupt controller doesn't support wake-up configuration,
irq_set_irq_wake() returns an error code. Then any subsequent call
trying to deconfigure wake-up will cause an imbalance, and a warning
will be printed:
WARNING: CPU: 1 PID: 1341 at kernel/irq/manage.c:540 irq_set_irq_wake+0x9c/0xf8()
Unbalanced IRQ 26 wake disable
To fix this, refrain from any further parent interrupt controller
(de)configuration if irq_set_irq_wake() failed.
Alternative fixes would be:
- calling "gic_set_irqchip_flags(IRQCHIP_SKIP_SET_WAKE)" from the
platform code,
- setting "gic_chip.flags = IRQCHIP_SKIP_SET_WAKE" in the GIC driver
code,
but these were withheld as the GIC hardware doesn't really support
wake-up interrupts.
Fixes: ab82fa7da4 ("gpio: rcar: Prevent module clock disable when wake-up is enabled")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the GPIO module is needed for wake-up, it's module clock must not
be disabled. Hence implement irq_chip.irq_set_wake(), which
increments/decrements the clock's enable_count when needed, and forwards
the wake-up state to the upstream interrupt controller.
This fixes wake-up from s2ram using gpio-keys when using a PM Domain to
manage the module clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The existing variable gpio_chip already points to the gpiochip instance,
hence use it everywhere.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switch the R-Car Gen2 GPIO driver to use the gpiolib irqchip helpers.
While doing this also make sure that gpiochip_irqchip_add() is called
after the gpiochip itself is registered, as required.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the call to devm_kzalloc() fails, nothing must be cleant up.
This was missed before because gpio_rcar_probe() had a "return"
statement after the first "goto err0".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: df0c6c8023 ("gpio: rcar: Add minimal runtime PM support")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle, and this time we got a lot of action going on and
it will continue:
- The core GPIO library implementation has been split up in
three different files:
- gpiolib.c for the latest and greatest and shiny GPIO
library code using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API
that we are phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are
not entirely happy with, but has to live on for
ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We
should have had the flags there from the beginning it
seems, now we need to clean up the mess. There is a plan
on how to move forward here devised by Alexandre Courbot
and Mark Brown.
- Split off a special <linux/gpio/machine.h> header for the
board gpio table registration, as per example from the
regulator subsystem.
- Start to kill off the return value from gpiochip_remove()
by removing the __must_check attribute and removing all
checks inside the drivers/gpio directory. The rationale
is: well what were we supposed to do if there is an error
code? Not much: print an error message. And gpiolib already
does that. So make this function return void eventually.
- Some cleanups of hairy gpiolib code, make some functions
not to be used outside the library private and make sure
they are not exported, remove gpiod_lock/unlock_as_irq()
as the existing function is for driver-internal use and
fine as it is, delete gpio_ensure_requested() as it is
not meaningful anymore.
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one()
function calls, which is logical since this is already
supported when referencing GPIOs from e.g. device trees.
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use
the gpiolib irqchip helpers cutting down on GPIO irqchip
boilerplate a bit more.
- New driver for the Zynq GPIO block.
- The usual incremental improvements around a bunch of
drivers.
- Janitorial syntactic and semantic cleanups by Jingoo Han,
and Rickard Strandqvist especially.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT5Ji9AAoJEEEQszewGV1zch8QAKp67+8ScxRBf/7RCSV6U/dy
i7kt+nP4au/TScwtjbX264DM8hroW7BzN+GqF10NEFeGkYDR+42lMav9PrNjtKtk
ojQPWdoGWzwwL0wa4j9rsuG/pRnbAEgDWPb+EkFdHQsLl6h71fyVoLOK+gKwJFyn
aPYGXyNbT1FN38oj1rarENiOUxM7VMXvcJFfvDYFdDDhCS4PLYPOMw0lrsGtsHMZ
epDa4z3yt4zHgYiUIT578nQ7EkIbGN3goywk3NQ+9WDQG+sLFHh4BdqcRKg6b9VM
I64+47uNQxkyvWCvcLma5ziqvtNQk113986g+cv5YeTh18Ajyio1kxEIZM181eBk
ITUPGrAorWHPLGNbe3psLmtK3+/BwmWIurPmHpckuW8d2JWWSVe0oepkUuqDwu/w
lUB5KtM0joFOr5k61fj5tCKxH344jc1zvHJ/N+bVYilbOMvunWzuMJlc4hADIGC2
1uxUAcPbYUAphGaxhdMBca9ellm0lWG19Gj5TtdGbRtNgp6R2qrwI66DDzk+1kLR
8Szx6KHQdEHFTlCLKSIAMv33p1ClfmNikhdicT3urwR8PeXmmTR1pD7kGmVTDDZa
gXSU5EilgGpak+77j/GZ2Ivp0Qt5M97UwWlZ7zTp++T1ZY+wwTHJI/09qcoWYjdz
IpZRIqrQchalbscpn3LY
=e+d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO update from Linus Walleij:
"This is the bulk of GPIO changes for the v3.17 development cycle, and
this time we got a lot of action going on and it will continue:
- The core GPIO library implementation has been split up in three
different files:
- gpiolib.c for the latest and greatest and shiny GPIO library code
using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API that we are
phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are not entirely
happy with, but has to live on for ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We should have
had the flags there from the beginning it seems, now we need to
clean up the mess. There is a plan on how to move forward here
devised by Alexandre Courbot and Mark Brown
- Split off a special <linux/gpio/machine.h> header for the board
gpio table registration, as per example from the regulator
subsystem
- Start to kill off the return value from gpiochip_remove() by
removing the __must_check attribute and removing all checks inside
the drivers/gpio directory. The rationale is: well what were we
supposed to do if there is an error code? Not much: print an error
message. And gpiolib already does that. So make this function
return void eventually
- Some cleanups of hairy gpiolib code, make some functions not to be
used outside the library private and make sure they are not
exported, remove gpiod_lock/unlock_as_irq() as the existing
function is for driver-internal use and fine as it is, delete
gpio_ensure_requested() as it is not meaningful anymore
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one() function
calls, which is logical since this is already supported when
referencing GPIOs from e.g. device trees
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use the gpiolib
irqchip helpers cutting down on GPIO irqchip boilerplate a bit more
- New driver for the Zynq GPIO block
- The usual incremental improvements around a bunch of drivers
- Janitorial syntactic and semantic cleanups by Jingoo Han, and
Rickard Strandqvist especially"
* tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (37 commits)
MAINTAINERS: update GPIO include files
gpio: add missing includes in machine.h
gpio: add flags argument to gpiod_get*() functions
MAINTAINERS: Update Samsung pin control entry
gpio / ACPI: Move event handling registration to gpiolib irqchip helpers
gpio: lynxpoint: Convert to use gpiolib irqchip
gpio: split gpiod board registration into machine header
gpio: remove gpio_ensure_requested()
gpio: remove useless check in gpiolib_sysfs_init()
gpiolib: Export gpiochip_request_own_desc and gpiochip_free_own_desc
gpio: move gpio_ensure_requested() into legacy C file
gpio: remove gpiod_lock/unlock_as_irq()
gpio: make gpiochip_get_desc() gpiolib-private
gpio: simplify gpiochip_export()
gpio: remove export of private of_get_named_gpio_flags()
gpio: Add support for GPIOF_ACTIVE_LOW to gpio_request_one functions
gpio: zynq: Clear pending interrupt when enabling a IRQ
gpio: drop retval check enforcing from gpiochip_remove()
gpio: remove all usage of gpio_remove retval in driver/gpio
devicetree: Add Zynq GPIO devicetree bindings documentation
...
The gpio-rcar driver has no IRQ domain OF xlate function and thus
ignores IRQ flags specified in DT. Fix this by using the two-cell xlate
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While it will be clamped to bool by gpiolib, let's make this sane
in the driver as well.
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is just enough to automatically enable the functional clock, if
present. Clock management during suspend/resume is still to be added.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-gpio@vger.kernel.org
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A big set this merge window, as we have much going on in
this subsystem. Major changes this time:
- Some core improvements and cleanups to the new GPIO
descriptor API. This seems to be working now so we can
start the exodus to this API, moving gradually away from
the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move
the few GPIO ACPI clients we have to the GPIO descriptor
API right *now* before we go any further. We actually
managed to contain this *before* we started to litter
the kernel with yet another hackish global numberspace for
the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have
been migrated to use the GPIO descriptors rather than
fixed number assignments. Tegra machine has been migrated
as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x.
Those should be really good examples of how I expect a
nice GPIO driver to look these days.
- Do away with custom GPIO implementations on a major
part of the ARM machines: ks8695, lpc32xx, mv78xx0.
Make a first step towards the same in the horribly
convoluted Samsung S3C include forest. We expect to
continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em,
intel-mid and lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line
is used for IRQs and can then enforce some semantics such
as disallowing a GPIO line marked as in use for IRQ to be
switched to output mode.
- Drop all use of irq_set_chip_and_handler_name().
The name provided in these cases were just unhelpful
tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em
74x164 and msm drivers.
- Some non-urgent bug fixes here and there, duplicate
#includes and that usual kind of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lW2i
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
According to the manual, if a port is set for level detection using
the corresponding bit in the edge/level select register and an external
level interrupt signal is asserted, the corresponding bit in INTDT
does not use the FF to hold the input.
Thus, writing 1 to the corresponding bits in INTCLR cannot clear the
corresponding bits in the INTDT register. Instead, when an external
input signal is stopped, the corresponding bit in INTDT is cleared
automatically.
Since the INTDT bit cannot be cleared for the level interrupts until
the interrupt signal is stopped, we end up with the infinite loop
when using deferred (threaded) IRQ handling.
Since a deferred interrupt is disabled by the low-level handler and
re-enabled only when the deferred handler is completed, Fix the issue
by dropping disabled interrupts from the pending mask as suggested by
Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Changes in V2:
* Drop disabled interrupts from pending mask altogether instead of
dropping level interrupts one by one once they get handled.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jianping Liu