This commit makes BBR use only the MSS (without any headers) to
calculate pacing rates when internal TCP-layer pacing is used.
This is necessary to achieve the correct pacing behavior in this case,
since tcp_internal_pacing() uses only the payload length to calculate
pacing delays.
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
Pull aio updates from Al Viro:
"Majority of AIO stuff this cycle. aio-fsync and aio-poll, mostly.
The only thing I'm holding back for a day or so is Adam's aio ioprio -
his last-minute fixup is trivial (missing stub in !CONFIG_BLOCK case),
but let it sit in -next for decency sake..."
* 'work.aio-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
aio: sanitize the limit checking in io_submit(2)
aio: fold do_io_submit() into callers
aio: shift copyin of iocb into io_submit_one()
aio_read_events_ring(): make a bit more readable
aio: all callers of aio_{read,write,fsync,poll} treat 0 and -EIOCBQUEUED the same way
aio: take list removal to (some) callers of aio_complete()
aio: add missing break for the IOCB_CMD_FDSYNC case
random: convert to ->poll_mask
timerfd: convert to ->poll_mask
eventfd: switch to ->poll_mask
pipe: convert to ->poll_mask
crypto: af_alg: convert to ->poll_mask
net/rxrpc: convert to ->poll_mask
net/iucv: convert to ->poll_mask
net/phonet: convert to ->poll_mask
net/nfc: convert to ->poll_mask
net/caif: convert to ->poll_mask
net/bluetooth: convert to ->poll_mask
net/sctp: convert to ->poll_mask
net/tipc: convert to ->poll_mask
...
This is additional to the
commit ea1627c20c ("tcp: minor optimizations around tcp_hdr() usage").
At this point, skb->data is same with tcp_hdr() as tcp header has not
been pulled yet. So use the less expensive one to get the tcp header.
Remove the third parameter of tcp_rcv_established() and put it into
the function body.
Furthermore, the local variables are listed as a reverse christmas tree :)
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP receives an out-of-order packet, it immediately sends
a SACK packet, generating network load but also forcing the
receiver to send 1-MSS pathological packets, increasing its
RTX queue length/depth, and thus processing time.
Wifi networks suffer from this aggressive behavior, but generally
speaking, all these SACK packets add fuel to the fire when networks
are under congestion.
This patch adds a high resolution timer and tp->compressed_ack counter.
Instead of sending a SACK, we program this timer with a small delay,
based on RTT and capped to 1 ms :
delay = min ( 5 % of RTT, 1 ms)
If subsequent SACKs need to be sent while the timer has not yet
expired, we simply increment tp->compressed_ack.
When timer expires, a SACK is sent with the latest information.
Whenever an ACK is sent (if data is sent, or if in-order
data is received) timer is canceled.
Note that tcp_sack_new_ofo_skb() is able to force a SACK to be sent
if the sack blocks need to be shuffled, even if the timer has not
expired.
A new SNMP counter is added in the following patch.
Two other patches add sysctls to allow changing the 1,000,000 and 44
values that this commit hard-coded.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket can not disappear under us.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create and export a new helper tcp_rack_skb_timeout and move tcp_is_rack
to prepare the final RTO change.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous approach for the lost and retransmit bits was to
wipe the slate clean: zero all the lost and retransmit bits,
correspondingly zero the lost_out and retrans_out counters, and
then add back the lost bits (and correspondingly increment lost_out).
The new approach is to treat this very much like marking packets
lost in fast recovery. We don’t wipe the slate clean. We just say
that for all packets that were not yet marked sacked or lost, we now
mark them as lost in exactly the same way we do for fast recovery.
This fixes the lost retransmit accounting at RTO time and greatly
simplifies the RTO code by sharing much of the logic with Fast
Recovery.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a rewrite of NewReno loss recovery implementation that is
simpler and standalone for readability and better performance by
using less states.
Note that NewReno refers to RFC6582 as a modification to the fast
recovery algorithm. It is used only if the connection does not
support SACK in Linux. It should not to be confused with the Reno
(AIMD) congestion control.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the classic DUPACK threshold rule
(#DupThresh) in RACK.
When the number of packets SACKed is greater or equal to the
threshold, RACK sets the reordering window to zero which would
immediately mark all the unsacked packets below the highest SACKed
sequence lost. Since this approach is known to not work well with
reordering, RACK only uses it if no reordering has been observed.
The DUPACK threshold rule is a particularly useful extension to the
fast recoveries triggered by RACK reordering timer. For example
data-center transfers where the RTT is much smaller than a timer
tick, or high RTT path where the default RTT/4 may take too long.
Note that this patch differs slightly from RFC6675. RFC6675
considers a packet lost when at least #DupThresh higher-sequence
packets are SACKed.
With RACK, for connections that have seen reordering, RACK
continues to use a dynamically-adaptive time-based reordering
window to detect losses. But for connections on which we have not
yet seen reordering, this patch considers a packet lost when at
least one higher sequence packet is SACKed and the total number
of SACKed packets is at least DupThresh. For example, suppose a
connection has not seen reordering, and sends 10 packets, and
packets 3, 5, 7 are SACKed. RFC6675 considers packets 1 and 2
lost. RACK considers packets 1, 2, 4, 6 lost.
There is some small risk of spurious retransmits here due to
reordering. However, this is mostly limited to the first flight of
a connection on which the sender receives SACKs from reordering.
And RFC 6675 and FACK loss detection have a similar risk on the
first flight with reordering (it's just that the risk of spurious
retransmits from reordering was slightly narrower for those older
algorithms due to the margin of 3*MSS).
Also the minimum reordering window is reduced from 1 msec to 0
to recover quicker on short RTT transfers. Therefore RACK is more
aggressive in marking packets lost during recovery to reduce the
reordering window timeouts.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-05-17
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Provide a new BPF helper for doing a FIB and neighbor lookup
in the kernel tables from an XDP or tc BPF program. The helper
provides a fast-path for forwarding packets. The API supports
IPv4, IPv6 and MPLS protocols, but currently IPv4 and IPv6 are
implemented in this initial work, from David (Ahern).
2) Just a tiny diff but huge feature enabled for nfp driver by
extending the BPF offload beyond a pure host processing offload.
Offloaded XDP programs are allowed to set the RX queue index and
thus opening the door for defining a fully programmable RSS/n-tuple
filter replacement. Once BPF decided on a queue already, the device
data-path will skip the conventional RSS processing completely,
from Jakub.
3) The original sockmap implementation was array based similar to
devmap. However unlike devmap where an ifindex has a 1:1 mapping
into the map there are use cases with sockets that need to be
referenced using longer keys. Hence, sockhash map is added reusing
as much of the sockmap code as possible, from John.
4) Introduce BTF ID. The ID is allocatd through an IDR similar as
with BPF maps and progs. It also makes BTF accessible to user
space via BPF_BTF_GET_FD_BY_ID and adds exposure of the BTF data
through BPF_OBJ_GET_INFO_BY_FD, from Martin.
5) Enable BPF stackmap with build_id also in NMI context. Due to the
up_read() of current->mm->mmap_sem build_id cannot be parsed.
This work defers the up_read() via a per-cpu irq_work so that
at least limited support can be enabled, from Song.
6) Various BPF JIT follow-up cleanups and fixups after the LD_ABS/LD_IND
JIT conversion as well as implementation of an optimized 32/64 bit
immediate load in the arm64 JIT that allows to reduce the number of
emitted instructions; in case of tested real-world programs they
were shrinking by three percent, from Daniel.
7) Add ifindex parameter to the libbpf loader in order to enable
BPF offload support. Right now only iproute2 can load offloaded
BPF and this will also enable libbpf for direct integration into
other applications, from David (Beckett).
8) Convert the plain text documentation under Documentation/bpf/ into
RST format since this is the appropriate standard the kernel is
moving to for all documentation. Also add an overview README.rst,
from Jesper.
9) Add __printf verification attribute to the bpf_verifier_vlog()
helper. Though it uses va_list we can still allow gcc to check
the format string, from Mathieu.
10) Fix a bash reference in the BPF selftest's Makefile. The '|& ...'
is a bash 4.0+ feature which is not guaranteed to be available
when calling out to shell, therefore use a more portable variant,
from Joe.
11) Fix a 64 bit division in xdp_umem_reg() by using div_u64()
instead of relying on the gcc built-in, from Björn.
12) Fix a sock hashmap kmalloc warning reported by syzbot when an
overly large key size is used in hashmap then causing overflows
in htab->elem_size. Reject bogus attr->key_size early in the
sock_hash_alloc(), from Yonghong.
13) Ensure in BPF selftests when urandom_read is being linked that
--build-id is always enabled so that test_stacktrace_build_id[_nmi]
won't be failing, from Alexei.
14) Add bitsperlong.h as well as errno.h uapi headers into the tools
header infrastructure which point to one of the arch specific
uapi headers. This was needed in order to fix a build error on
some systems for the BPF selftests, from Sirio.
15) Allow for short options to be used in the xdp_monitor BPF sample
code. And also a bpf.h tools uapi header sync in order to fix a
selftest build failure. Both from Prashant.
16) More formally clarify the meaning of ID in the direct packet access
section of the BPF documentation, from Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch only refactors the existing sockmap code. This will allow
much of the psock initialization code path and bpf helper codes to
work for both sockmap bpf map types that are backed by an array, the
currently supported type, and the new hash backed bpf map type
sockhash.
Most the fallout comes from three changes,
- Pushing bpf programs into an independent structure so we
can use it from the htab struct in the next patch.
- Generalizing helpers to use void *key instead of the hardcoded
u32.
- Instead of passing map/key through the metadata we now do
the lookup inline. This avoids storing the key in the metadata
which will be useful when keys can be longer than 4 bytes. We
rename the sk pointers to sk_redir at this point as well to
avoid any confusion between the current sk pointer and the
redirect pointer sk_redir.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
linux-4.16 got support for softirq based hrtimers.
TCP can switch its pacing hrtimer to this variant, since this
avoids going through a tasklet and some atomic operations.
pacing timer logic looks like other (jiffies based) tcp timers.
v2: use hrtimer_try_to_cancel() in tcp_clear_xmit_timers()
to correctly release reference on socket if needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Called when a TCP segment is acknowledged.
Could be used by application protocols who hold additional
metadata associated with the stream data.
This is required by TLS device offload to release
metadata associated with acknowledged TLS records.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some networks can make sure TCP payload can exactly fit 4KB pages,
with well chosen MSS/MTU and architectures.
Implement mmap() system call so that applications can avoid
copying data without complex splice() games.
Note that a successful mmap( X bytes) on TCP socket is consuming
bytes, as if recvmsg() has been done. (tp->copied += X)
Only PROT_READ mappings are accepted, as skb page frags
are fundamentally shared and read only.
If tcp_mmap() finds data that is not a full page, or a patch of
urgent data, -EINVAL is returned, no bytes are consumed.
Application must fallback to recvmsg() to read the problematic sequence.
mmap() wont block, regardless of socket being in blocking or
non-blocking mode. If not enough bytes are in receive queue,
mmap() would return -EAGAIN, or -EIO if socket is in a state
where no other bytes can be added into receive queue.
An application might use SO_RCVLOWAT, poll() and/or ioctl( FIONREAD)
to efficiently use mmap()
On the sender side, MSG_EOR might help to clearly separate unaligned
headers and 4K-aligned chunks if necessary.
Tested:
mlx4 (cx-3) 40Gbit NIC, with tcp_mmap program provided in following patch.
MTU set to 4168 (4096 TCP payload, 40 bytes IPv6 header, 32 bytes TCP header)
Without mmap() (tcp_mmap -s)
received 32768 MB (0 % mmap'ed) in 8.13342 s, 33.7961 Gbit,
cpu usage user:0.034 sys:3.778, 116.333 usec per MB, 63062 c-switches
received 32768 MB (0 % mmap'ed) in 8.14501 s, 33.748 Gbit,
cpu usage user:0.029 sys:3.997, 122.864 usec per MB, 61903 c-switches
received 32768 MB (0 % mmap'ed) in 8.11723 s, 33.8635 Gbit,
cpu usage user:0.048 sys:3.964, 122.437 usec per MB, 62983 c-switches
received 32768 MB (0 % mmap'ed) in 8.39189 s, 32.7552 Gbit,
cpu usage user:0.038 sys:4.181, 128.754 usec per MB, 55834 c-switches
With mmap() on receiver (tcp_mmap -s -z)
received 32768 MB (100 % mmap'ed) in 8.03083 s, 34.2278 Gbit,
cpu usage user:0.024 sys:1.466, 45.4712 usec per MB, 65479 c-switches
received 32768 MB (100 % mmap'ed) in 7.98805 s, 34.4111 Gbit,
cpu usage user:0.026 sys:1.401, 43.5486 usec per MB, 65447 c-switches
received 32768 MB (100 % mmap'ed) in 7.98377 s, 34.4296 Gbit,
cpu usage user:0.028 sys:1.452, 45.166 usec per MB, 65496 c-switches
received 32768 MB (99.9969 % mmap'ed) in 8.01838 s, 34.281 Gbit,
cpu usage user:0.02 sys:1.446, 44.7388 usec per MB, 65505 c-switches
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SO_RCVLOWAT is properly handled in tcp_poll(), so that POLLIN is only
generated when enough bytes are available in receive queue, after
David change (commit c7004482e8 "tcp: Respect SO_RCVLOWAT in tcp_poll().")
But TCP still calls sk->sk_data_ready() for each chunk added in receive
queue, meaning thread is awaken, and goes back to sleep shortly after.
Tested:
tcp_mmap test program, receiving 32768 MB of data with SO_RCVLOWAT set to 512KB
-> Should get ~2 wakeups (c-switches) per MB, regardless of how many
(tiny or big) packets were received.
High speed (mostly full size GRO packets)
received 32768 MB (100 % mmap'ed) in 8.03112 s, 34.2266 Gbit,
cpu usage user:0.037 sys:1.404, 43.9758 usec per MB, 65497 c-switches
received 32768 MB (99.9954 % mmap'ed) in 7.98453 s, 34.4263 Gbit,
cpu usage user:0.03 sys:1.422, 44.3115 usec per MB, 65485 c-switches
Low speed (sender is ratelimited and sends 1-MSS at a time, so GRO is not helping)
received 22474.5 MB (100 % mmap'ed) in 6015.35 s, 0.0313414 Gbit,
cpu usage user:0.05 sys:1.586, 72.7952 usec per MB, 44950 c-switches
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications might use SO_RCVLOWAT on TCP socket hoping to receive
one [E]POLLIN event only when a given amount of bytes are ready in socket
receive queue.
Problem is that receive autotuning is not aware of this constraint,
meaning sk_rcvbuf might be too small to allow all bytes to be stored.
Add a new (struct proto_ops)->set_rcvlowat method so that a protocol
can override the default setsockopt(SO_RCVLOWAT) behavior.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is second part of dealing with suboptimal device gso parameters.
In first patch (350c9f484b "tcp_bbr: better deal with suboptimal GSO")
we dealt with devices having low gso_max_segs
Some devices lower gso_max_size from 64KB to 16 KB (r8152 is an example)
In order to probe an optimal cwnd, we want BBR being not sensitive
to whatever GSO constraint a device can have.
This patch removes tso_segs_goal() CC callback in favor of
min_tso_segs() for CC wanting to override sysctl_tcp_min_tso_segs
Next patch will remove bbr->tso_segs_goal since it does not have
to be persistent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
배석진 reported that in some situations, packets for a given 5-tuple
end up being processed by different CPUS.
This involves RPS, and fragmentation.
배석진 is seeing packet drops when a SYN_RECV request socket is
moved into ESTABLISH state. Other states are protected by socket lock.
This is caused by a CPU losing the race, and simply not caring enough.
Since this seems to occur frequently, we can do better and perform
a second lookup.
Note that all needed memory barriers are already in the existing code,
thanks to the spin_lock()/spin_unlock() pair in inet_ehash_insert()
and reqsk_put(). The second lookup must find the new socket,
unless it has already been accepted and closed by another cpu.
Note that the fragmentation could be avoided in the first place by
use of a correct TCP MSS option in the SYN{ACK} packet, but this
does not mean we can not be more robust.
Many thanks to 배석진 for a very detailed analysis.
Reported-by: 배석진 <soukjin.bae@samsung.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The selftests test_maps program was leaving dangling BPF sockmap
programs around because not all psock elements were removed from
the map. The elements in turn hold a reference on the BPF program
they are attached to causing BPF programs to stay open even after
test_maps has completed.
The original intent was that sk_state_change() would be called
when TCP socks went through TCP_CLOSE state. However, because
socks may be in SOCK_DEAD state or the sock may be a listening
socket the event is not always triggered.
To resolve this use the ULP infrastructure and register our own
proto close() handler. This fixes the above case.
Fixes: 174a79ff95 ("bpf: sockmap with sk redirect support")
Reported-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Create a UID field and enum that can be used to assign ULPs to
sockets. This saves a set of string comparisons if the ULP id
is known.
For sockmap, which is added in the next patches, a ULP is used to
hook into TCP sockets close state. In this case the ULP being added
is done at map insert time and the ULP is known and done on the kernel
side. In this case the named lookup is not needed. Because we don't
want to expose psock internals to user space socket options a user
visible flag is also added. For TLS this is set for BPF it will be
cleared.
Alos remove pr_notice, user gets an error code back and should check
that rather than rely on logs.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Adds support for passing up to 4 arguments to sock_ops bpf functions. It
reusues the reply union, so the bpf_sock_ops structures are not
increased in size.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds a macro, SOCK_OPS_SET_FIELD, for writing to
struct tcp_sock or struct sock fields. This required adding a new
field "temp" to struct bpf_sock_ops_kern for temporary storage that
is used by sock_ops_convert_ctx_access. It is used to store and recover
the contents of a register, so the register can be used to store the
address of the sk. Since we cannot overwrite the dst_reg because it
contains the pointer to ctx, nor the src_reg since it contains the value
we want to store, we need an extra register to contain the address
of the sk.
Also adds the macro SOCK_OPS_GET_OR_SET_FIELD that calls one of the
GET or SET macros depending on the value of the TYPE field.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A persistent connection may send tiny amount of data (e.g. health-check)
for a long period of time. BBR's windowed min RTT filter may only see
RTT samples from delayed ACKs causing BBR to grossly over-estimate
the path delay depending how much the ACK was delayed at the receiver.
This patch skips RTT samples that are likely coming from delayed ACKs. Note
that it is possible the sender never obtains a valid measure to set the
min RTT. In this case BBR will continue to set cwnd to initial window
which seems fine because the connection is thin stream.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, active Fast Open is paused on a specific
destination IP address if the previous connections to the
IP address have experienced recurring timeouts . But recent
experiments by Microsoft (https://goo.gl/cykmn7) and Mozilla
browsers indicate the isssue is often caused by broken middle-boxes
sitting close to the client. Therefore it is much better user
experience if Fast Open is disabled out-right globally to avoid
experiencing further timeouts on connections toward other
destinations.
This patch changes the destination-IP disablement to global
disablement if a connection experiencing recurring timeouts
or aborts due to timeout. Repeated incidents would still
exponentially increase the pause time, starting from an hour.
This is extremely conservative but an unfortunate compromise to
minimize bad experience due to broken middle-boxes.
Reported-by: Dragana Damjanovic <ddamjanovic@mozilla.com>
Reported-by: Patrick McManus <mcmanus@ducksong.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2017-12-07
The following pull-request contains BPF updates for your net-next tree.
The main changes are:
1) Detailed documentation of BPF development process from Daniel.
2) Addition of is_fullsock, snd_cwnd and srtt_us fields to bpf_sock_ops
from Lawrence.
3) Minor follow up for bpf_skb_set_tunnel_key() from William.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark tcp_sock during a SACK reneging event and invalidate rate samples
while marked. Such rate samples may overestimate bw by including packets
that were SACKed before reneging.
< ack 6001 win 10000 sack 7001:38001
< ack 7001 win 0 sack 8001:38001 // Reneg detected
> seq 7001:8001 // RTO, SACK cleared.
< ack 38001 win 10000
In above example the rate sample taken after the last ack will count
7001-38001 as delivered while the actual delivery rate likely could
be much lower i.e. 7001-8001.
This patch adds a new field tcp_sock.sack_reneg and marks it when we
declare SACK reneging and entering TCP_CA_Loss, and unmarks it after
the last rate sample was taken before moving back to TCP_CA_Open. This
patch also invalidates rate samples taken while tcp_sock.is_sack_reneg
is set.
Fixes: b9f64820fb ("tcp: track data delivery rate for a TCP connection")
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds read access to snd_cwnd and srtt_us fields of tcp_sock. Since these
fields are only valid if the socket associated with the sock_ops program
call is a full socket, the field is_fullsock is also added to the
bpf_sock_ops struct. If the socket is not a full socket, reading these
fields returns 0.
Note that in most cases it will not be necessary to check is_fullsock to
know if there is a full socket. The context of the call, as specified by
the 'op' field, can sometimes determine whether there is a full socket.
The struct bpf_sock_ops has the following fields added:
__u32 is_fullsock; /* Some TCP fields are only valid if
* there is a full socket. If not, the
* fields read as zero.
*/
__u32 snd_cwnd;
__u32 srtt_us; /* Averaged RTT << 3 in usecs */
There is a new macro, SOCK_OPS_GET_TCP32(NAME), to make it easier to add
read access to more 32 bit tcp_sock fields.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
After this fix : ("tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()"),
socket lookups happen while skb->cb[] has not been mangled yet by TCP.
Fixes: a04a480d43 ("net: Require exact match for TCP socket lookups if dif is l3mdev")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the TLP scheduling logic so that when scheduling a TLP probe, we
ensure that the estimated time at which an RTO would fire accounts for
the fact that ACKs indicating forward progress should push back RTO
times.
After the following fix:
df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
we had an unintentional behavior change in the following kind of
scenario: suppose the RTT variance has been very low recently. Then
suppose we send out a flight of N packets and our RTT is 100ms:
t=0: send a flight of N packets
t=100ms: receive an ACK for N-1 packets
The response before df92c8394e that was:
-> schedule a TLP for now + RTO_interval
The response after df92c8394e is:
-> schedule a TLP for t=0 + RTO_interval
Since RTO_interval = srtt + RTT_variance, this means that we have
scheduled a TLP timer at a point in the future that only accounts for
RTT_variance. If the RTT_variance term is small, this means that the
timer fires soon.
Before df92c8394e this would not happen, because in that code, when
we receive an ACK for a prefix of flight, we did:
1) Near the top of tcp_ack(), switch from TLP timer to RTO
at write_queue_head->paket_tx_time + RTO_interval:
if (icsk->icsk_pending == ICSK_TIME_LOSS_PROBE)
tcp_rearm_rto(sk);
2) In tcp_clean_rtx_queue(), update the RTO to now + RTO_interval:
if (flag & FLAG_ACKED) {
tcp_rearm_rto(sk);
3) In tcp_ack() after tcp_fastretrans_alert() switch from RTO
to TLP at now + RTO_interval:
if (icsk->icsk_pending == ICSK_TIME_RETRANS)
tcp_schedule_loss_probe(sk);
In df92c8394e we removed that 3-phase dance, and instead directly
set the TLP timer once: we set the TLP timer in cases like this to
write_queue_head->packet_tx_time + RTO_interval. So if the RTT
variance is small, then this means that this is setting the TLP timer
to fire quite soon. This means if the ACK for the tail of the flight
takes longer than an RTT to arrive (often due to delayed ACKs), then
the TLP timer fires too quickly.
Fixes: df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make default TCP default congestion control to a per namespace
value. This changes default congestion control to a pointer to congestion ops
(rather than implicit as first element of available lsit).
The congestion control setting of new namespaces is inherited
from the current setting of the root namespace.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FACK loss detection has been disabled by default and the
successor RACK subsumed FACK and can handle reordering better.
This patch removes FACK to simplify TCP loss recovery.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that when a new netns is created, it inherits its
sysctl_tcp_rmem and sysctl_tcp_wmem from initial netns.
This change is needed so that we can refine TCP rcvbuf autotuning,
to take RTT into consideration.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently TCP RACK loss detection does not work well if packets are
being reordered beyond its static reordering window (min_rtt/4).Under
such reordering it may falsely trigger loss recoveries and reduce TCP
throughput significantly.
This patch improves that by increasing and reducing the reordering
window based on DSACK, which is now supported in major TCP implementations.
It makes RACK's reo_wnd adaptive based on DSACK and no. of recoveries.
- If DSACK is received, increment reo_wnd by min_rtt/4 (upper bounded
by srtt), since there is possibility that spurious retransmission was
due to reordering delay longer than reo_wnd.
- Persist the current reo_wnd value for TCP_RACK_RECOVERY_THRESH (16)
no. of successful recoveries (accounts for full DSACK-based loss
recovery undo). After that, reset it to default (min_rtt/4).
- At max, reo_wnd is incremented only once per rtt. So that the new
DSACK on which we are reacting, is due to the spurious retx (approx)
after the reo_wnd has been updated last time.
- reo_wnd is tracked in terms of steps (of min_rtt/4), rather than
absolute value to account for change in rtt.
In our internal testing, we observed significant increase in throughput,
in scenarios where reordering exceeds min_rtt/4 (previous static value).
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on SNMP values provided by Roman, Yuchung made the observation
that some crashes in tcp_sacktag_walk() might be caused by MTU probing.
Looking at tcp_mtu_probe(), I found that when a new skb was placed
in front of the write queue, we were not updating tcp highest sack.
If one skb is freed because all its content was copied to the new skb
(for MTU probing), then tp->highest_sack could point to a now freed skb.
Bad things would then happen, including infinite loops.
This patch renames tcp_highest_sack_combine() and uses it
from tcp_mtu_probe() to fix the bug.
Note that I also removed one test against tp->sacked_out,
since we want to replace tp->highest_sack regardless of whatever
condition, since keeping a stale pointer to freed skb is a recipe
for disaster.
Fixes: a47e5a988a ("[TCP]: Convert highest_sack to sk_buff to allow direct access")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_SKB program types use bpf_compute_data to store the end of the
packet data. However, bpf_compute_data assumes the cb is stored in the
qdisc layer format. But, for SK_SKB this is the wrong layer of the
stack for this type.
It happens to work (sort of!) because in most cases nothing happens
to be overwritten today. This is very fragile and error prone.
Fortunately, we have another hole in tcp_skb_cb we can use so lets
put the data_end value there.
Note, SK_SKB program types do not use data_meta, they are failed by
sk_skb_is_valid_access().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
two extra #include are not necessary in tcp.h
Remove them.
Fixes: 40304b2a15 ("bpf: BPF support for sock_ops")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove an obsolete comment about TCP pacing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that sysctl_tcp_thin_dupack was not used, I deleted it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMC protocol [1] relies on the use of a new TCP experimental
option [2, 3]. With this option, SMC capabilities are exchanged
between peers during the TCP three way handshake. This patch adds
support for this experimental option to TCP.
References:
[1] SMC-R Informational RFC: http://www.rfc-editor.org/info/rfc7609
[2] Shared Use of TCP Experimental Options RFC 6994:
https://tools.ietf.org/rfc/rfc6994.txt
[3] IANA ExID SMCR:
http://www.iana.org/assignments/tcp-parameters/tcp-parameters.xhtml#tcp-exids
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already allow to enable TFO without a cookie by using the
fastopen-sysctl and setting it to TFO_SERVER_COOKIE_NOT_REQD (or
TFO_CLIENT_NO_COOKIE).
This is safe to do in certain environments where we know that there
isn't a malicous host (aka., data-centers) or when the
application-protocol already provides an authentication mechanism in the
first flight of data.
A server however might be providing multiple services or talking to both
sides (public Internet and data-center). So, this server would want to
enable cookie-less TFO for certain services and/or for connections that
go to the data-center.
This patch exposes a socket-option and a per-route attribute to enable such
fine-grained configurations.
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
New socket option TCP_FASTOPEN_KEY to allow different keys per
listener. The listener by default uses the global key until the
socket option is set. The key is a 16 bytes long binary data. This
option has no effect on regular non-listener TCP sockets.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_SKB BPF programs are run from the socket/tcp context but early in
the stack before much of the TCP metadata is needed in tcp_skb_cb. So
we can use some unused fields to place BPF metadata needed for SK_SKB
programs when implementing the redirect function.
This allows us to drop the preempt disable logic. It does however
require an API change so sk_redirect_map() has been updated to
additionally provide ctx_ptr to skb. Note, we do however continue to
disable/enable preemption around actual BPF program running to account
for map updates.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove three inline helpers that are no longer needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yury reported crash with this signature :
[ 554.034021] [<ffff80003ccd5a58>] 0xffff80003ccd5a58
[ 554.034156] [<ffff00000888fd34>] skb_release_all+0x14/0x30
[ 554.034288] [<ffff00000888fd64>] __kfree_skb+0x14/0x28
[ 554.034409] [<ffff0000088ece6c>] tcp_sendmsg_locked+0x4dc/0xcc8
[ 554.034541] [<ffff0000088ed68c>] tcp_sendmsg+0x34/0x58
[ 554.034659] [<ffff000008919fd4>] inet_sendmsg+0x2c/0xf8
[ 554.034783] [<ffff0000088842e8>] sock_sendmsg+0x18/0x30
[ 554.034928] [<ffff0000088861fc>] SyS_sendto+0x84/0xf8
Problem is that skb->destructor contains garbage, and this is
because I accidentally removed tcp_skb_tsorted_anchor_cleanup()
from tcp_unlink_write_queue()
This would trigger with a write(fd, <invalid_memory>, len) attempt,
and we will add to packetdrill this capability to avoid future
regressions.
Fixes: 75c119afe1 ("tcp: implement rb-tree based retransmit queue")
Reported-by: Yury Norov <ynorov@caviumnetworks.com>
Tested-by: Yury Norov <ynorov@caviumnetworks.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a linear list to store all skbs in write queue has been okay
for quite a while : O(N) is not too bad when N < 500.
Things get messy when N is the order of 100,000 : Modern TCP stacks
want 10Gbit+ of throughput even with 200 ms RTT flows.
40 ns per cache line miss means a full scan can use 4 ms,
blowing away CPU caches.
SACK processing often can use various hints to avoid parsing
whole retransmit queue. But with high packet losses and/or high
reordering, hints no longer work.
Sender has to process thousands of unfriendly SACK, accumulating
a huge socket backlog, burning a cpu and massively dropping packets.
Using an rb-tree for retransmit queue has been avoided for years
because it added complexity and overhead, but now is the time
to be more resistant and say no to quadratic behavior.
1) RTX queue is no longer part of the write queue : already sent skbs
are stored in one rb-tree.
2) Since reaching the head of write queue no longer needs
sk->sk_send_head, we added an union of sk_send_head and tcp_rtx_queue
Tested:
On receiver :
netem on ingress : delay 150ms 200us loss 1
GRO disabled to force stress and SACK storms.
for f in `seq 1 10`
do
./netperf -H lpaa6 -l30 -- -K bbr -o THROUGHPUT|tail -1
done | awk '{print $0} {sum += $0} END {printf "%7u\n",sum}'
Before patch :
323.87
351.48
339.59
338.62
306.72
204.07
304.93
291.88
202.47
176.88
2840
After patch:
1700.83
2207.98
2070.17
1544.26
2114.76
2124.89
1693.14
1080.91
2216.82
1299.94
18053
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the upcoming rtx rbtree will add some extra code,
it is time to not inline this fat function anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new queue (list) that tracks the sent but not yet
acked or SACKed skbs for a TCP connection. The list is chronologically
ordered by skb->skb_mstamp (the head is the oldest sent skb).
This list will be used to optimize TCP Rack recovery, which checks
an skb's timestamp to judge if it has been lost and needs to be
retransmitted. Since TCP write queue is ordered by sequence instead
of sent time, RACK has to scan over the write queue to catch all
eligible packets to detect lost retransmission, and iterates through
SACKed skbs repeatedly.
Special cares for rare events:
1. TCP repair fakes skb transmission so the send queue needs adjusted
2. SACK reneging would require re-inserting SACKed skbs into the
send queue. For now I believe it's not worth the complexity to
make RACK work perfectly on SACK reneging, so we do nothing here.
3. Fast Open: currently for non-TFO, send-queue correctly queues
the pure SYN packet. For TFO which queues a pure SYN and
then a data packet, send-queue only queues the data packet but
not the pure SYN due to the structure of TFO code. This is okay
because the SYN receiver would never respond with a SACK on a
missing SYN (i.e. SYN is never fast-retransmitted by SACK/RACK).
In order to not grow sk_buff, we use an union for the new list and
_skb_refdst/destructor fields. This is a bit complicated because
we need to make sure _skb_refdst and destructor are properly zeroed
before skb is cloned/copied at transmit, and before being freed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in the TCP code, the initialization sequence for cached
metrics, congestion control, BPF, etc, after successful connection
is very inconsistent. This introduces inconsistent bevhavior and is
prone to bugs. The current call sequence is as follows:
(1) for active case (tcp_finish_connect() case):
tcp_mtup_init(sk);
icsk->icsk_af_ops->rebuild_header(sk);
tcp_init_metrics(sk);
tcp_call_bpf(sk, BPF_SOCK_OPS_ACTIVE_ESTABLISHED_CB);
tcp_init_congestion_control(sk);
tcp_init_buffer_space(sk);
(2) for passive case (tcp_rcv_state_process() TCP_SYN_RECV case):
icsk->icsk_af_ops->rebuild_header(sk);
tcp_call_bpf(sk, BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB);
tcp_init_congestion_control(sk);
tcp_mtup_init(sk);
tcp_init_buffer_space(sk);
tcp_init_metrics(sk);
(3) for TFO passive case (tcp_fastopen_create_child()):
inet_csk(child)->icsk_af_ops->rebuild_header(child);
tcp_init_congestion_control(child);
tcp_mtup_init(child);
tcp_init_metrics(child);
tcp_call_bpf(child, BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB);
tcp_init_buffer_space(child);
This commit uniforms the above functions to have the following sequence:
tcp_mtup_init(sk);
icsk->icsk_af_ops->rebuild_header(sk);
tcp_init_metrics(sk);
tcp_call_bpf(sk, BPF_SOCK_OPS_ACTIVE/PASSIVE_ESTABLISHED_CB);
tcp_init_congestion_control(sk);
tcp_init_buffer_space(sk);
This sequence is the same as the (1) active case. We pick this sequence
because this order correctly allows BPF to override the settings
including congestion control module and initial cwnd, etc from
the route, and then allows the CC module to see those settings.
Suggested-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require different tcp_fastopen_key
independently of the host.
David Miller pointed out there is a leak without releasing the context
of tcp_fastopen_key during netns teardown. So add the release action in
exit_batch path.
Tested:
1. Container namespace:
# cat /proc/sys/net/ipv4/tcp_fastopen_key:
2817fff2-f803cf97-eadfd1f3-78c0992b
cookie key in tcp syn packets:
Fast Open Cookie
Kind: TCP Fast Open Cookie (34)
Length: 10
Fast Open Cookie: 1e5dd82a8c492ca9
2. Host:
# cat /proc/sys/net/ipv4/tcp_fastopen_key:
107d7c5f-68eb2ac7-02fb06e6-ed341702
cookie key in tcp syn packets:
Fast Open Cookie
Kind: TCP Fast Open Cookie (34)
Length: 10
Fast Open Cookie: e213c02bf0afbc8a
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'publish' logic is not necessary after commit dfea2aa654 ("tcp:
Do not call tcp_fastopen_reset_cipher from interrupt context"), because
in tcp_fastopen_cookie_gen，it wouldn't call tcp_fastopen_init_key_once.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require enable TCP Fast Open
feature independently of the host.
This patch series continues making more of the TCP Fast Open related
sysctl knobs be per net-namespace.
Reported-by: Luca BRUNO <lucab@debian.org>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently no error is emitted, but this infrastructure will
used by the next patch to allow source address validation
for mcast sockets.
Since early demux can do a route lookup and an ipv4 route
lookup can return an error code this is consistent with the
current ipv4 route infrastructure.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->rbnode shares space with skb->next, skb->prev and skb->tstamp
Current uses (TCP receive ofo queue and netem) need to save/restore
tstamp, while skb->dev is either NULL (TCP) or a constant for a given
queue (netem).
Since we plan using an RB tree for TCP retransmit queue to speedup SACK
processing with large BDP, this patch exchanges skb->dev and
skb->tstamp.
This saves some overhead in both TCP and netem.
v2: removes the swtstamp field from struct tcp_skb_cb
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove tcp_may_send_now and tcp_snd_test that are no longer used
Fixes: 840a3cbe89 ("tcp: remove forward retransmit feature")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 45f119bf93.
Eric Dumazet says:
We found at Google a significant regression caused by
45f119bf93 tcp: remove header prediction
In typical RPC (TCP_RR), when a TCP socket receives data, we now call
tcp_ack() while we used to not call it.
This touches enough cache lines to cause a slowdown.
so problem does not seem to be HP removal itself but the tcp_ack()
call. Therefore, it might be possible to remove HP after all, provided
one finds a way to elide tcp_ack for most cases.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change was a followup to the header prediction removal,
so first revert this as a prerequisite to back out hp removal.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few bugs around refcnt handling in the new BPF congestion
control setsockopt:
- The new ca is assigned to icsk->icsk_ca_ops even in the case where we
cannot get a reference on it. This would lead to a use after free,
since that ca is going away soon.
- Changing the congestion control case doesn't release the refcnt on
the previous ca.
- In the reinit case, we first leak a reference on the old ca, then we
call tcp_reinit_congestion_control on the ca that we have just
assigned, leading to deinitializing the wrong ca (->release of the
new ca on the old ca's data) and releasing the refcount on the ca
that we actually want to use.
This is visible by building (for example) BIC as a module and setting
net.ipv4.tcp_congestion_control=bic, and using tcp_cong_kern.c from
samples/bpf.
This patch fixes the refcount issues, and moves reinit back into tcp
core to avoid passing a ca pointer back to BPF.
Fixes: 91b5b21c7c ("bpf: Add support for changing congestion control")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SOF_TIMESTAMPING_RX_SOFTWARE is enabled for tcp sockets, return the
timestamp corresponding to the highest sequence number data returned.
Previously the skb->tstamp is overwritten when a TCP packet is placed
in the out of order queue. While the packet is in the ooo queue, save the
timestamp in the TCB_SKB_CB. This space is shared with the gso_*
options which are only used on the tx path, and a previously unused 4
byte hole.
When skbs are coalesced either in the sk_receive_queue or the
out_of_order_queue always choose the timestamp of the appended skb to
maintain the invariant of returning the timestamp of the last byte in
the recvmsg buffer.
Signed-off-by: Mike Maloney <maloney@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a second device index, sdif, to inet6 socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
TCP moves the data in the cb. Prior to tcp_v4_rcv (e.g., early demux) the
ingress index is obtained from IPCB using inet_sdif and after tcp_v4_rcv
tcp_v4_sdif is used.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet