New function twl4030_remove_script(u8 flags) takes a script type as
defined in twl.h and prevents any script already loaded in that position
from running. This is accomplished by programming SEQ_ADD_* to 0x3f,
the END_OF_SCRIPT value, where SEQ_ADD_* is determined by flags.
(Future) users of this function include OMAP board files for machines
facing a race condition between sleep and warm reset.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add base address for generic slave ID0, ID1, ID2
and introduced one more entry to align RTC module number between
twl4030 and twl6030
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch disables TWL4030/5030 I2C1 adn I2C4(SR) internal pull-up, to
use only the external HW resistor >=470 Ohm for the assured
functionality in HS mode.
While testing the I2C in High Speed mode, it was discovered that
without a proper pull-up resistor, there is data corruption during
multi-byte transfer. RTC(time_set) test case was used for testing.
From the analysis done, it was concluded that ideally we need a
pull-up of 1.6k Ohm(recomended) or atleast 470 Ohm or greater for
assured performance in HS mode.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TWL4030_BCI_BATTERY config option originates from a patch to the
omap git tree. However inclusion in linux was seemingly rejected and
the functionality nears inclusion under a different name so this
removes the bits of the old version that made it into the mainline
kernel again.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Most of the GPIO expanders controlled by the pca953x driver are able to
report changes on the input pins through an *INT pin.
This patch implements the irq_chip functionality (edge detection only).
The driver has been tested on an Arcom Zeus.
[akpm@linux-foundation.org: the compiler does inlining for us nowadays]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
linux/i2c/pca953x.h is a very bare include file. Fix check for multiple
includes of linux/i2c/pca953x.h, and add dependent includes into the
header file.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to have TWL6030 CODEC driver as a platform driver, codec data
should be passed through twl_platform_data structure.
For twl6030 audio codec, the following data may be passed:
- audpwron_gpio: gpio line used to power-up/down the codec. A low-to-high
transition powers codec up. Setting audpwron_gpio to a negative value
means that codec will use manual power sequence instead of automatic
sequence
- naudint_irq: irq line for audio interrupt. twl6030 drives NAUDINT line
to low when an interrupt (codec ready, plug insertion/removal, etc) is
detected
However, codec driver can operate if any or none of them are passed.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds initial support for creating twl6030 PMIC
specific voltage regulators in the twl mfd driver.
Board specific regulator configurations will have to be passed from
respective board files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch updates the regulator driver to add support
for TWL6030 PMIC specific LDO regulators.
SMPS resources are not yet supported for TWL6030 and
also .set_mode and .get_status for LDO's are yet to
be implemented for TWL6030.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add all twl4030 regulators to the twl4030 mfd driver and
twl4030_platform_data
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TWL5031 introduces two new interrupts in PIH. Moreover, BCI
has changed remarkably and, thus, it's disabled when TWL5031
is in use.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add function to allow the configuation fo the VDCDC2 register by
external users, to allow changing of the standard and low-power
running modes.
This is needed, for example, for the Simtec IM2440D20 where we need
to use the low-power mode to shutdown the LDO/DCDC that are not needed
during suspend (saving substantial power) and the runtime use of the
low-power mode to change VCore.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allows TWL's 32kHz oscillator to go in low-power mode when
main battery voltage is running low.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The code tries to skip values initialized with -1, but since the values
are unsigned the comparison is always true.
The patch eliminates the following compiler warnings:
drivers/mfd/twl4030-power.c: In function 'twl4030_configure_resource':
drivers/mfd/twl4030-power.c:338: warning: comparison is always true due to
limited range of data type
drivers/mfd/twl4030-power.c:358: warning: comparison is always true due to
limited range of data type
drivers/mfd/twl4030-power.c:363: warning: comparison is always true due to
limited range of data type
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The <RESOURCE>_REMAP register allows configuration of the <RESOURCE> in case
of a sleep or off transition.
Allow this property of resources to be configured (through twl4030_resconfig)
and add code to parse these values to program the registers accordingly.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add audio_mclk to the platform data struct for the
twl4030-codec MFD driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
New MFD child to twl4030 MFD device.
Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.
This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.
The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The original driver was written with the KEY() macro defined as (col,
row) instead of (row, col) as defined by the matrix keypad
infrastructure. So the keymap was defined accordingly. Since the
driver that was merged upstream uses the matrix keypad infrastructure,
modify the keymap accordingly.
While we are at it, fix the comments in twl4030.h and define
PERSISTENT_KEY as (r,c) instead of (c, r)
Tested on a RX51 (N900) device.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MELPAS MCS-5000 is the touchscreen controller. The overview of this
controller can see at the following website:
http://www.melfas.com/product/product01.asp?k_r=eng_
This driver is tested on s3c6410 NCP board and supports only the i2c
interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The TWL4030/5030 family of multifunction devices allows board-specific
control of the the various regulators, clock and reset lines through
'scripts' that are loaded into its memory. This allows for Dynamic Power
Switching (DPS).
Implement board-independent core support for DPS that is then used by
board-specific code to load custom DPS scripts.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a driver for the keypad controller on TWL4030 family chips.
These support up to an 8x8 key matrix. The TWL4030 multifunction
chips are mostly used on OMAP3 (or OMAP 2430) based boards.
[dtor@mail.ru: switch to matrix-keypad framework, fix changing
keymap from userspace]
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: add driver for Synaptics I2C touchpad
Input: synaptics - add support for reporting x/y resolution
Input: ALPS - handle touchpoints buttons correctly
Input: gpio-keys - change timer to workqueue
Input: ads7846 - pin change interrupt support
Input: add support for touchscreen on W90P910 ARM platform
Input: appletouch - improve finger detection
Input: wacom - clear Intuos4 wheel data when finger leaves proximity
Input: ucb1400 - move static function from header into core
Input: add driver for EETI touchpanels
Input: ads7846 - more detailed model name in sysfs
Input: ads7846 - support swapping x and y axes
Input: ati_remote2 - use non-atomic bitops
Input: introduce lm8323 keypad driver
Input: psmouse - ESD workaround fix for OLPC XO touchpad
Input: tsc2007 - make sure platform provides get_pendown_state()
Input: uinput - flush all pending ff effects before destroying device
Input: simplify name handling for certain input handles
Input: serio - do not use deprecated dev.power.power_state
Input: wacom - add support for Intuos4 tablets
...
Add support to the PCA953x driver to use the GPIOLIB naming facility for
GPIOs.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lm8323 is the keypad driver used in n810 device.
[akpm@linux-foundation.org: coding-style fixes]
[dtor@mail.ru: various cleanups]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Support for the s6000 on-chip i2c controller.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (32 commits)
regulator: twl4030 VAUX3 supports 3.0V
regulator: Support disabling of unused regulators by machines
regulator: Don't increment use_count for boot_on regulators
twl4030-regulator: expose VPLL2
regulator: refcount fixes
regulator: Don't warn if we failed to get a regulator
regulator: Allow boot_on regulators to be disabled by clients
regulator: Implement list_voltage for WM835x LDOs and DCDCs
twl4030-regulator: list more VAUX4 voltages
regulator: Don't warn on omitted voltage constraints
regulator: Implement list_voltage() for WM8400 DCDCs and LDOs
MMC: regulator utilities
regulator: twl4030 voltage enumeration (v2)
regulator: twl4030 regulators
regulator: get_status() grows kerneldoc
regulator: enumerate voltages (v2)
regulator: Fix get_mode() for WM835x DCDCs
regulator: Allow regulators to set the initial operating mode
regulator: Suggest use of datasheet supply or pin names for consumers
regulator: email - update email address and regulator webpage.
...
In the case of at24, the platform code registers a 'setup' callback with
the at24_platform_data. When the at24 driver detects an EEPROM, it fills
out the read and write functions of the memory_accessor and calls the
setup callback passing the memory_accessor struct. The platform code can
then use the read/write functions in the memory_accessor struct for
reading and writing the EEPROM.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support most of the LDO regulators in the twl4030 family chips.
In the case of LDOs supporting MMC/SD, the voltage controls are
used; but in most other cases, the regulator framework is only
used to enable/disable a supplies, conserving power when a given
voltage rail is not needed.
The drivers/mfd/twl4030-core.c code already sets up the various
regulators according to board-specific configuration, and knows
that some chips don't provide the full set of voltage rails.
The omitted regulators are intended to be under hardware control,
such as during the hardware-mediated system powerup, powerdown,
and suspend states. Unless/until software hooks are known to
be safe, they won't be exported here.
These regulators implement the new get_status() operation, but
can't realistically implement get_mode(); the status output is
effectively the result of a vote, with the relevant hardware
inputs not exposed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: i8042 - add Dell Vostro 1510 to nomux list
Input: gtco - use USB endpoint API
Input: add support for Maple controller as a joystick
Input: atkbd - broaden the Dell DMI signatures
Input: HIL drivers - add MODULE_ALIAS()
Input: map_to_7segment.h - convert to __inline__ for userspace
Input: add support for enhanced rotary controller on pxa930 and pxa935
Input: add support for trackball on pxa930 and pxa935
Input: add da9034 touchscreen support
Input: ads7846 - strict_strtoul takes unsigned long
Input: make some variables and functions static
Input: add tsc2007 based touchscreen driver
Input: psmouse - add module parameters to control OLPC touchpad delays
Input: i8042 - add Gigabyte M912 netbook to noloop exception table
Input: atkbd - Samsung NC10 key repeat fix
Input: atkbd - add keyboard quirk for HP Pavilion ZV6100 laptop
Input: libps2 - handle 0xfc responses from devices
Input: add support for Wacom W8001 penabled serial touchscreen
Input: synaptics - report multi-taps only if supported by the device
Input: add joystick driver for Walkera WK-0701 RC transmitter
...
Provide a static debounce configuration mechanism for twl4030 GPIOs,
replacing the previous dynamic one. The single user of that mechanism was
for MMC card detect debouncing.
Boards can provide a bitmask saying which GPIOs to debounce (30 msec).
It's always enabled for pins with the MMC card-detect/VMMCx link active,
so most boards won't need to set the debounce mask.
This is a net code shrink, including runtime footprint.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Basic MFD framework for the MSP430 microcontroller firmware used
on the dm355evm board:
- Provides an interface for other drivers: register read/write
utilities, and register declarations.
- Directly exports:
* Many signals through the GPIO framework
+ LEDs
+ SW6 through gpio sysfs
+ NTSC/nPAL jumper through gpio sysfs
+ ... more could be added later, e.g. MMC signals
* Child devices:
+ LEDs, via leds-gpio child (and default triggers)
+ RTC, via rtc-dm355evm child device
+ Buttons and IR control, via dm355evm_keys
- Supports power-off system call. Use the reset button to power
the board back up; the power supply LED will be on, but the
MSP430 waits to re-activate the regulators.
- On probe() this:
* Announces firmware revision
* Turns off the banked LEDs
* Exports the resources noted above
* Hooks the power-off support
* Muxes tvp5146 -or- imager for video input
Unless the new tvp514x driver (tracked for mainline) is configured,
this assumes that some custom imager driver handles video-in.
This completely ignores the registers reporting the output voltages
on the various power supplies. Someone could add a hwmon interface
if that seems useful.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This contains two bugfixes to the initial twl4030 regulator
support patch related to USB:
(a) always overwrite the old list of consumers ... else
the regulator handles all use the same "usb1v5" name;
(b) don't set up the "usbcp" regulator, which turns out
to be managed through separate controls, usually ULPI
directly from the OTG controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Initial code to create twl4030 voltage regulator devices, using
the new regulator framework. Note that this now starts to care
what name is used to declare the TWL chip:
- TWL4030 is the "old" chip; newer ones have a bigger variety
of VAUX2 voltages.
- TWL5030 is the core "new" chip; TPS65950 is its catalog version.
- The TPS65930 and TPS65920 are cost-reduced catalog versions of
TWL5030 parts ... fewer regulators, no battery charger, etc.
Board-specific regulator configuration should be provided, listing
which regulators are used and their constraints (e.g. 1.8V only).
Code that could ("should"?) leverage the regulator stuff includes
TWL4030 USB transceiver support and MMC glue, LCD support for the
3430SDP and Labrador boards, and S-Video output.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Finish removing dependency of TWL driver stack on platform-specific
IRQ definitions ... and remove the build dependency on OMAP.
This lets the TWL4030 code be included in test builds for most
platforms, and will make it easier for non-OMAP folk to update
most of this code for new APIs etc.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Minor change to the TWL4030 utility interface: support reads
of all 256 bytes in each register bank (vs just 255). This
can help when debugging, but is otherwise a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This drive has been tested on ARM9 based SoC - MV86XX.
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- Move it into a separate file; clean and streamline it
- Restructure the init code for reuse during secondary dispatch
- Support both levels (primary, secondary) of IRQ dispatch
- Use a workqueue for irq mask/unmask and trigger configuration
Code for two subchips currently share that secondary handler code.
One is the power subchip; its IRQs are now handled by this core,
courtesy of this patch. The other is the GPIO module, which will
be supported through a later patch.
There are also minor changes to the header file, mostly related
to GPIO support; nothing yet in mainline cares about those. A
few references to OMAP-specific symbols are disabled; when they
can all be removed, the TWL4030 support ceases being OMAP-specific.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds the core of the TWL4030 driver, which supports
chips including the TPS65950. These chips are multi-function; see
http://focus.ti.com/docs/prod/folders/print/tps65950.html
Public specs are in the works. For now, the block diagram on
the second page of the datasheet is fairly informative.
There are some known issues with this core code. Most notably,
the IRQ dispatching needs simplification (to use more of genirq),
generalization (integrating support for secondary IRQ dispatch
as well as primary, and removing the build dependency on OMAP),
and then probably updating to leverage threaded IRQ support
(expected to arrive in mainline "soon").
Once the core is in mainline, drivers for other parts of this
chip can follow its lead and start swimming upstream too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This adds a driver supporting a family of I2C port expanders from Maxim,
which includes the MAX7319 and MAX7320-7327 chips.
[dbrownell@users.sourceforge.net: minor fixes]
Signed-off-by: Jack Ren <jack.ren@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new-style driver for most I2C EEPROMs, giving sysfs read/write
access to their data. Tested with various chips and clock rates.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the old driver_name/type scheme for i2c driver matching. Only the
standard aliasing model will be used from now on.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Mike Turquette