This function is going to be used for templates as well, so we need to
pass the pointer separately.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push key/mask dumping from fl_dump() into a separate function
fl_dump_key(), that will be reused for template dumping.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user to set a template for newly created chains. Template lock
down the chain for particular classifier type/options combinations.
The classifier needs to support templates, otherwise kernel would
reply with error.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user to create, destroy, get and dump chain objects. Do that by
extending rtnl commands by the chain-specific ones. User will now be
able to explicitly create or destroy chains (so far this was done only
automatically according the filter/act needs and refcounting). Also, the
user will receive notification about any chain creation or destuction.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, chain 0 is implicitly created during block creation. However
that does not align with chain object exposure, creation and destruction
api introduced later on. So make the chain 0 behave the same way as any
other chain and only create it when it is needed. Since chain 0 is
somehow special as the qdiscs need to hold pointer to the first chain
tp, this requires to move the chain head change callback infra to the
block structure.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push all bits that take care of ops lookup, including module loading
outside tcf_proto_create() function, into tcf_proto_lookup_ops()
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk says:
====================
net: ethernet: ti: cpsw: add MQPRIO and CBS Qdisc offload
This series adds MQPRIO and CBS Qdisc offload for TI cpsw driver.
It potentially can be used in audio video bridging (AVB) and time
sensitive networking (TSN).
Patchset was tested on AM572x EVM and BBB boards. Last patch from this
series adds detailed description of configuration with examples. For
consistency reasons, in role of talker and listener, tools from
patchset "TSN: Add qdisc based config interface for CBS" were used and
can be seen here: https://www.spinics.net/lists/netdev/msg460869.html
Based on net-next/master
v5..v4:
- corrected typo of "am57xx" board name, no functional changes
v4..v3:
- nothing, just rebase
v3..v2:
- corrected typo of "shaper" word, no functional changes
v2..v1:
- changed name cpsw.txt on ti-cpsw.txt
- changed name cpsw_set_tc() on cpsw_set_mqprio()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This document describes MQPRIO and CBS Qdisc offload configuration
for cpsw driver based on examples. It potentially can be used in
audio video bridging (AVB) and time sensitive networking (TSN).
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to restore shapers configuration after interface was down/up.
This is needed as appropriate configuration is still replicated in
kernel settings. This only shapers context restore, so vlan
configuration should be restored by user if needed, especially for
devices with one port where vlan frames are sent via ALE.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw has up to 4 FIFOs per port and upper 3 FIFOs can feed rate
limited queue with shaping. In order to set and enable shaping for
those 3 FIFOs queues the network device with CBS qdisc attached is
needed. The CBS configuration is added for dual-emac/single port mode
only, but potentially can be used in switch mode also, based on
switchdev for instance.
Despite the FIFO shapers can work w/o cpdma level shapers the base
usage must be in combine with cpdma level shapers as described in TRM,
that are set as maximum rates for interface queues with sysfs.
One of the possible configuration with txq shapers and CBS shapers:
Configured with echo RATE >
/sys/class/net/eth0/queues/tx-0/tx_maxrate
/---------------------------------------------------
/
/ cpdma level shapers
+----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+
| c7 | | c6 | | c5 | | c4 | | c3 | | c2 | | c1 | | c0 |
\ / \ / \ / \ / \ / \ / \ / \ /
\ / \ / \ / \ / \ / \ / \ / \ /
\/ \/ \/ \/ \/ \/ \/ \/
+---------|------|------|------|-------------------------------------+
| +----+ | | +---+ |
| | +----+ | | |
| v v v v |
| +----+ +----+ +----+ +----+ p p+----+ +----+ +----+ +----+ |
| | | | | | | | | o o| | | | | | | | |
| | f3 | | f2 | | f1 | | f0 | r CPSW r| f3 | | f2 | | f1 | | f0 | |
| | | | | | | | | t t| | | | | | | | |
| \ / \ / \ / \ / 0 1\ / \ / \ / \ / |
| \ X \ / \ / \ / \ / \ / \ / \ / |
| \/ \ \/ \/ \/ \/ \/ \/ \/ |
+-------\------------------------------------------------------------+
\
\ FIFO shaper, set with CBS offload added in this patch,
\ FIFO0 cannot be rate limited
------------------------------------------------------
CBS shaper configuration is supposed to be used with root MQPRIO Qdisc
offload allowing to add sk_prio->tc->txq maps that direct traffic to
appropriate tx queue and maps L2 priority to FIFO shaper.
The CBS shaper is intended to be used for AVB where L2 priority
(pcp field) is used to differentiate class of traffic. So additionally
vlan needs to be created with appropriate egress sk_prio->l2 prio map.
If CBS has several tx queues assigned to it, the sum of their
bandwidth has not overlap bandwidth set for CBS. It's recomended the
CBS bandwidth to be a little bit more.
The CBS shaper is configured with CBS qdisc offload interface using tc
tool from iproute2 packet.
For instance:
$ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1
$ tc -g class show dev eth0
+---(100:ffe2) mqprio
| +---(100:3) mqprio
| +---(100:4) mqprio
|
+---(100:ffe1) mqprio
| +---(100:2) mqprio
|
+---(100:ffe0) mqprio
+---(100:1) mqprio
$ tc qdisc add dev eth0 parent 100:1 cbs locredit -1440 \
hicredit 60 sendslope -960000 idleslope 40000 offload 1
$ tc qdisc add dev eth0 parent 100:2 cbs locredit -1470 \
hicredit 62 sendslope -980000 idleslope 20000 offload 1
The above code set CBS shapers for tc0 and tc1, for that txq0 and
txq1 is used. Pay attention, the real set bandwidth can differ a bit
due to discreteness of configuration parameters.
Here parameters like locredit, hicredit and sendslope are ignored
internally and are supposed to be set with assumption that maximum
frame size for frame - 1500.
It's supposed that interface speed is not changed while reconnection,
not always is true, so inform user in case speed of interface was
changed, as it can impact on dependent shapers configuration.
For more examples see Documentation.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's possible to offload vlan to tc priority mapping with
assumption sk_prio == L2 prio.
Example:
$ ethtool -L eth0 rx 1 tx 4
$ qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1
$ tc -g class show dev eth0
+---(100:ffe2) mqprio
| +---(100:3) mqprio
| +---(100:4) mqprio
|
+---(100:ffe1) mqprio
| +---(100:2) mqprio
|
+---(100:ffe0) mqprio
+---(100:1) mqprio
Here, 100:1 is txq0, 100:2 is txq1, 100:3 is txq2, 100:4 is txq3
txq0 belongs to tc0, txq1 to tc1, txq2 and txq3 to tc2
The offload part only maps L2 prio to classes of traffic, but not
to transmit queues, so to direct traffic to traffic class vlan has
to be created with appropriate egress map.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to TRM tx rated channels should be in 7..0 order,
so correct it.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpdma channel highest priority is from hi to lo number.
The driver has limited number of descriptors that are shared between
number of cpdma channels. Number of queues can be tuned with ethtool,
that allows to not spend descriptors on not needed cpdma channels.
In AVB usually only 2 tx queues can be enough with rate limitation.
The rate limitation can be used only for hi priority queues. Thus, to
use only 2 queues the 8 has to be created. It's wasteful.
So, in order to allow using only needed number of rate limited
tx queues, save resources, and be able to set rate limitation for
them, let assign tx cpdma channels in backward order to queues.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes update for mlx5e net device driver.
1) From Feras Daoud, Added the support for firmware log tracing,
first by introducing the firmware API needed for the task and then
For each PF do the following:
1- Allocate memory for the tracer strings database and read it from the FW to the SW.
2- Allocate and dma map tracer buffers.
Traces that will be written into the buffer will be parsed as a group
of one or more traces, referred to as trace message. The trace message
represents a C-like printf string.
Once a new trace is available FW will generate an event indicates new trace/s are
available and the driver will parse them and dump them using tracepoints
event tracing
Enable mlx5 fw tracing by:
echo 1 > /sys/kernel/debug/tracing/events/mlx5/mlx5_fw/enable
Read traces by:
cat /sys/kernel/debug/tracing/trace
2) From Roi Dayan, Remove redundant WARN when we cannot find neigh entry
3) From Jianbo Liu, TC double vlan support
- Support offloading tc double vlan headers match
- Support offloading double vlan push/pop tc actions
4) From Boris, re-visit UDP GSO, remove the splitting of UDP_GSO_L4 packets
in the driver, and exposes UDP_GSO_L4 as a PARTIAL_GSO feature.
-----BEGIN PGP SIGNATURE-----
iQEbBAABAgAGBQJbVlEZAAoJEEg/ir3gV/o+x00H8gKfpMcKoDpT/EOq0NbCjnHI
87cxUqtk999TaoxD7YbNjQh6vyMvQOE6WwEZIIpvc6JzeSWtYN9FELyQC+deYH+/
299WbfdiPxADfBB2DzbTlPhGOgaO26zA+yAYgdp7FW9M1r3USWExaUg1UzMTdxKR
4CsWUsG+yB3KlAKvuGjjRU1bN/+NivmK5mgT9PXd9m9fjobBENERU8dscCVmpMro
o2z6ajKZ26a0jo0az99vDBUu6t1SC6QN1nJHY3iWBVY1Mvjy9XrcQ4LDR5wSjelU
EiM9Hn2eVg5OddrlFEEi7yEeLHgtda3p/3qb1zx2YY9vuUM79R3MYz0uAPuaIw==
=j+2g
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-07-18-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-07-18
This series includes update for mlx5e net device driver.
1) From Feras Daoud, Added the support for firmware log tracing,
first by introducing the firmware API needed for the task and then
For each PF do the following:
1- Allocate memory for the tracer strings database and read it from the FW to the SW.
2- Allocate and dma map tracer buffers.
Traces that will be written into the buffer will be parsed as a group
of one or more traces, referred to as trace message. The trace message
represents a C-like printf string.
Once a new trace is available FW will generate an event indicates new trace/s are
available and the driver will parse them and dump them using tracepoints
event tracing
Enable mlx5 fw tracing by:
echo 1 > /sys/kernel/debug/tracing/events/mlx5/mlx5_fw/enable
Read traces by:
cat /sys/kernel/debug/tracing/trace
2) From Roi Dayan, Remove redundant WARN when we cannot find neigh entry
3) From Jianbo Liu, TC double vlan support
- Support offloading tc double vlan headers match
- Support offloading double vlan push/pop tc actions
4) From Boris, re-visit UDP GSO, remove the splitting of UDP_GSO_L4 packets
in the driver, and exposes UDP_GSO_L4 as a PARTIAL_GSO feature.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the splitting of UDP_GSO_L4 packets in the driver,
and exposes UDP_GSO_L4 as a PARTIAL_GSO feature. Thus, the network stack
is not responsible for splitting the packet into two.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As we can configure two push/pop actions in one flow table entry,
add support to offload those double vlan actions in a rule to HW.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Extract actions offloading code to a new function, and also extend data
structures for double vlan actions.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We can match on both outer and inner vlan tags, add support for
offloading that.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
It is possible for neigh entry not to exist if it was cleaned already.
When we bring down an interface the neigh gets deleted but it could be
that our listener for neigh event to clear the encap valid bit didn't
start yet and the neigh update last used work is started first.
In this scenario the encap entry has valid bit set but the neigh entry
doesn't exist.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the tracer file to the makefile and add the init
function to the load one flow.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For each message the driver should do the following:
1- Find the message string in the strings database
2- Count the param number of each message
3- Wait for the param events and accumulate them
4- Calculate the event timestamp using the local event timestamp
and the first timestamp event following it.
5- Print message to trace log
Enable the tracing by:
echo 1 > /sys/kernel/debug/tracing/events/mlx5/mlx5_fw/enable
Read traces by:
cat /sys/kernel/debug/tracing/trace
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The tracer has one event, event 0x26, with two subtypes:
- Subtype 0: Ownership change
- Subtype 1: Traces available
An ownership change occurs in the following cases:
1- Owner releases his ownership, in this case, an event will be
sent to inform others to reattempt acquire ownership.
2- Ownership was taken by a higher priority tool, in this case
the owner should understand that it lost ownership, and go through
tear down flow.
The second subtype indicates that there are traces in the trace buffer,
in this case, the driver polls the tracer buffer for new traces, parse
them and prepares the messages for printing.
The HW starts tracing from the first address in the tracer buffer.
Driver receives an event notifying that new trace block exists.
HW posts a timestamp event at the last 8B of every 256B block.
Comparing the timestamp to the last handled timestamp would indicate
that this is a new trace block. Once the new timestamp is detected,
the entire block is considered valid.
Block validation and parsing, should be done after copying the current
block to a different location, in order to avoid block overwritten
during processing.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For each PF do the following:
1- Allocate memory for the tracer strings database and read the
strings from the FW to the SW. These strings will be used later for
parsing traces.
2- Allocate and dma map tracer buffers.
Traces that will be written into the buffer will be parsed as a group
of one or more traces, referred to as trace message. The trace message
represents a C-like printf string.
First trace of a message holds the pointer to the correct string in
strings database. The following traces holds the variables of the
message.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement FW tracer logic and registers access, initialization and
cleanup flows.
Initializing the tracer will be part of load one flow, as multiple
PFs will try to acquire ownership but only one will succeed and will
be the tracer owner.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 core infrastructure updates and fixes.
From Eran:
- Add MPEGC (Management PCIe General Configuration) registers and btis
- Fix tristate and description for MLX5 module
rom Feras:
- Add hardware structures for the firmware tracer
From Jainbo:
- Core support for double vlan push/pop steering action
From Max:
- Add XRQ commands definitions
From Noa:
- Add missing SET_DRIVER_VERSION command translation
From Roi:
- Use ERR_CAST() instead of coding it
From Tariq:
- Better return types for CQE API
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Bryan Whitehead says:
====================
lan743x: Add features to lan743x driver
This patch series adds extra features to the lan743x driver.
Updates for v4:
Patch 6/8 - Modified get/set_wol to use super set of
MAC and PHY driver support.
Patch 7/9 - In set_eee, return the return value from phy_ethtool_set_eee.
Updates for v3:
Removed patch 9 from this series, regarding PTP support
Patch 6/8 - Add call to phy_ethtool_get_wol to lan743x_ethtool_get_wol
Patch 7/8 - Add call to phy_ethtool_set_eee on (!eee->eee_enabled)
Updates for v2:
Patch 3/9 - Used ARRAY_SIZE macro in lan743x_ethtool_get_ethtool_stats.
Patch 5/9 - Used MAX_EEPROM_SIZE in lan743x_ethtool_set_eeprom.
Patch 6/9 - Removed unnecessary read of PMT_CTL.
Used CRC algorithm from lib.
Removed PHY interrupt settings from lan743x_pm_suspend
Change "#if CONFIG_PM" to "#ifdef CONFIG_PM"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement power management
Supports suspend, resume, and Wake on LAN
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool eeprom access
Also provides access to OTP (One Time Programming)
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool message level
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool statistics
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use default link setting functions
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool get_drvinfo
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov says:
====================
sh_eth: clean up the TSU register accessors
Here's a set of 5 patches against DaveM's 'net-next.git' repo. They do
a final clean up of the TSU register accessors...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_tsu_read_entry() is still asymmetric with sh_eth_tsu_write_entry()
WRT their prototypes -- make them symmetric by passing to the former a TSU
register offset instead of its address and also adding the (now necessary)
'ndev' parameter...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can add the TSU register base address to a TSU register offset right
in sh_eth_tsu_write_entry(), no need to do it in its callers...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With sh_eth_tsu_get_offset() now actually returning TSU register's offset,
we can at last use it in sh_eth_tsu_{read|write}(). Somehow this saves 248
bytes of object code with AArch64 gcc 4.8.5... :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_tsu_get_offset(), despite its name, returns a TSU register's address,
not its offset. Make this function match its name and return a register's
offset from the TSU registers base address instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_tsu_get_offset() is called several times by the driver, remove
*inline* and move that function from the header to the driver itself
to let gcc decide whether to expand it inline or not...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qe_muram_alloc return a unsigned long integer,which should not
compared with zero. check it using IS_ERR_VALUE() to fix this.
Fixes: c19b6d246a ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: patches 2018-07-23
here are some small patches for SMC: Just the first patch contains a
functional change. It allows to differ between the modes SMCR and SMCD
on s390 when monitoring SMC sockets. The remaining patches are cleanups
without functional changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The page map address is already stored in the RMB descriptor.
There is no need to derive it from the cpu_addr value.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link group field tokens_used_mask is a bitmap. Use macro
DECLARE_BITMAP for its definition.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a frequently used construct with a more readable variant,
reducing the code. Also might come handy when we start to support
more than a single per link group.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions to read and write cursors are exclusively used to copy
cursors. Therefore switch to a respective function instead.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename field diag_fallback into diag_mode and set the smc mode of a
connection explicitly.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for device-only IPv6 multipath next hops was dropped in
commit 33bd5ac54d ("net/ipv6: Revert attempt to simplify route replace
and append") and as of commit b5d2d75e07 ("net/ipv6: Do not allow
device only routes via the multipath API"), attempts to add a next hop
like that yield an explicit diagnostic.
Correspondingly, drop the IPv6 parts of GRE multipath test that are
supposed to test that code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko