Empirically, this improves performance slightly (~2% max IOPS) by
allowing cmd_alloc to remember where it left off searching for
free commands between calls instead of always starting its search
at command 0.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This means changing the allocator to reference count commands.
The reference count is now the authoritative indicator of whether a
command is allocated or not. The h->cmd_pool_bits bitmap is now
only a heuristic hint to speed up the allocation process, it is no
longer the authoritative record of allocated commands.
Since we changed the command allocator to use reference counting
as the authoritative indicator of whether a command is allocated,
fail_all_outstanding_cmds needs to use the reference count not
h->cmd_pool_bits for this purpose.
Fix hpsa_drain_accel_commands to use the reference count as the
authoritative indicator of whether a command is allocated instead of
the h->cmd_pool_bits bitmap.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When using the ioaccel submission methods, requests destined for RAID volumes
are sometimes diverted to physical devices. The OS has no or limited
knowledge of these physical devices, so it is up to the driver to avoid
pushing the device too hard. It is better to honor the physical device queue
limit rather than making the device spew zillions of TASK SET FULL responses.
This is so that hpsa based devices support /sys/block/sdNN/device/queue_type
of simple, which lets the SCSI midlayer automatically adjust the queue_depth
based on TASK SET FULL and GOOD status.
Adjust the queue depth for a new device after it is created based on the
maximum queue depths of the physical devices that constitute the
device. This drops the maximum queue depth from .can_queue of 1024 to
something like 174 for single-drive RAID-0, 348 for two-drive RAID-1, etc.
It also adjusts for the ratio of data to parity drives.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead of kicking the commands all the way back to the mid
layer, use a work queue. This enables having a mechanism for
the driver to be able to resubmit the commands down the "normal"
raid path without turning off the ioaccel feature entirely
whenever an error is encountered on the ioaccel path, and
prevent excessive rescanning of devices.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Factor out the bottom part of the queuecommand function
which is the part that builds commands for submitting down
the "normal' RAID stack path of a Smart Array.
Need to factor this out to improve how commands that
were initially sent down one of the "ioaccellerated"
paths but which have some sort of error condition are
retried down the "normal" path.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The original reasoning behind doing this was faulty. An error
of some sort would be encountered, accelerated i/o would be
disabled for that logical drive, the command would be kicked
back out to the SCSI midlayer for a retry, and since i/o accelerator
mode was disabled, it would get retried down the RAID path.
However, something needs to turn ioaccellerator mode back on,
and this rescan request was what did that. However, it was racy,
and extremely bad for performance to rescan all devices, so,
don't do that.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
By not doing maintaining a list of queued commands, we can eliminate some spin
locking in the main i/o path and gain significant improvement in IOPS. Remove
the queuing code and the code that calls it; remove now-unused interrupt code;
remove DIRECT_LOOKUP_BIT.
Now that the passthru commands share the same command pool as
the main i/o path, and the total size of the pool is less than
or equal to the number of commands that will fit in the hardware
fifo, there is no need to check to see if we are exceeding the
hardware fifo's depth.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We have commands reserved for internal use.
This is laying the groundwork for removing the internal
queue of commands from the driver so that the locks that
protect that queue may be removed.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We need to reserve some commands for device rescans,
aborts, and the pass through ioctls, etc. so we cannot
give them all to the scsi mid layer.
This is in preparation for removing cmd_special_alloc and
cmd_special_free so that we can stop queuing commands internally
in the driver so that we can remove the locks thta protect the
queue that we will no longer have.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If hpsa_allocate_cmd_pool failed, we were calling two functions unnecessarily:
hpsa_free_sg_chain_blocks(h);
hpsa_free_cmd_pool(h);
This didn't cause any problem, as those functions can tolerate being called
when what they free hasn't been allocated (relevant pointers would be NULL)
but it is potentially confusing.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Partial allocation failure wasn't handled correctly
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Return the actual error code instead of a generic error code.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make the function name more descriptive. We use more than
one interrupt.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Enhance error reporting.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cleanup comments to be more specific. Make messages more
informational.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Encapsulate the conditional predicate which tests for legacy controllers
in a separate function and rework the code comments.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There is nothing worrisome about the "Waiting for controller to
respond to no-op" print, so use dev_info rather than dev_warn.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If the board ID lookup function fails, return the return
code rather than return -ENODEV.
The only board ID failure reason right now is -ENODEV,
so this just provides more informative prints in kdump
and adapts to future changes.
Tested with error injection while booting with
reset_devices
on the kernel command line:
[ 62.804324] injecting error in inj_hpsa_lookup_board_id: 1 11
[ 62.804423] hpsa 0000:04:00.0: Board ID not found
(the pci probe layer does not print an additional
message if -ENODEV is the reason)
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Return the real reason for kdump_hard_reset failure rather
than change them all to -ENODEV.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The queue depth printed at startup is in decimal, so
shouldn't have a 0x prefix.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In MSI and MSI-X mode, where hpsa asks for more than one interrupt,
hpsa_request_irqs forgets if the first request_irq call failed
if later ones succeed.
It needs to exit the loop on any failure rather than continue,
freeing all irqs that were requested until that point.
Also, it needs to clear out the q numbers up to MAX_REPLY_QUEUES.
The same is true for the general hpsa_free_irqs function.
Tested with error injection of -ENOSYS on the 4th call:
[ 9.277691] injecting error in inj_request_irq: 1 4
[ 9.277780] hpsa 0000:02:00.0: failed to get irq 35 for hpsa1
[ 10.711623] scsi host1: Error handler scsi_eh_1 exiting
[ 10.739170] hpsa: probe of 0000:02:00.0 failed with error -38
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove unused variable in hpsa_free_cmd_pool.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Change the function names to have hpsa prefix.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
HP now uses RAID-6 rather than RAID-ADG (Advanced Data Guarding)
as the marketing name for our implementation of RAID-6.
The driver considers RAID-1 and RAID-1+0 to be the same level, and
considers RAID-1ADM and RAID-1+0ADM to be the same level. Parenthesis
can be used to reflect the optional +0 portion of both those RAID levels.
Rename: RAID-ADG to RAID-6
RAID-1(1+0) to RAID-1(+0)
RAID-1(ADM) to RAID-1(+0)ADM
Also, add another const after the pointer type as suggested
by checkpatch.pl so the array is:
static const char * const raid_label[]
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We change drive queue depths to match drive reported queue depths.
The name of the SML function was changed from scsi_adjust_queue_depth
changed to scsi_change_queue_depth.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Change how SA controllers are reset by changing PCI power levels.
The hpsa driver was finding the PCI_PM_CTRL_STATE_MASK offset
then reading/writing a bitmask to change the power state. There
are kernel functions that do the same operations. Better to use
the kernel functions.
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Sometimes when the card is restarted it may cause -
"irq 16: nobody cared (try booting with the "irqpoll" option)"
that is likely caused so, that the card, after the hard reset
finishes, pulls on the irq. Disabling the ints before or after
the hpsa_kdump_hard_reset_controller fixes it.
At this point we can't know in which state the card is,
so using SA5_INTR_OFF + SA5_REPLY_INTR_MASK_OFFSET defines directly,
instead of the function the drivers provides, seems to be apropriate.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There is a potential memory leak in hpsa_kdump_hard_reset_controller.
Reviewed-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Correct endiness issues reported by sparse. SA controllers are
little endian. This patch ensures endiness correctness.
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds support for Qualcomm Technologies Inc platforms that
use UFS driver. for example, it adds :
- PM specific operations during hibern8, suspend, resume, clock setup
- qcom-ufs generic phy driver initialization, calibration,
power-on/off sequence, etc.
- UFS Controller specific configuration
- Rate, Gear, Mode negotiation between device and controller
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds a support for a 14nm qcom-ufs phy that is
required in platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds a support for a 20nm qcom-ufs phy that is required in
platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change adds a generic and common API support for ufs phy QUALCOMM
Technologies. This support provides common code and also points
to specific phy callbacks to differentiate between different behaviors
of frequent use-cases (like power on, power off, phy calibration etc).
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The midlayer scsi logging already logs the command and sense code
if the logging level is high enough, no need to duplicate that
in the sr driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Bottomley <JBottomley@Parallels.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
The midlayer logging already prints the cdb details if the logging
level is high enough, no need to duplicate this in the ch driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Bottomley <JBottomley@Parallels.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Bottomley <JBottomley@Parallels.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Bottomley <JBottomley@Parallels.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We should only try to evaluate the cdb if this is an ATAPI
device, for any other device the 'cdb' field and the cdb_len
has no meaning.
Fixes: cbba5b0ee4
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tejun Heo <tj@kernel.org>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump mpt2sas driver version to 20.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Added a support to set cpu affinity mask for each MSIX vector enabled
by the HBA. So that, running the irqbalancer will balance interrupts among
the cpus.
Change_set:
1. Added affinity_hint varable of type cpumask_var_t in adapter_reply_queue
structure. And allocated a memory for this varable by calling
alloc_cpumask_var.
2. Call the API irq_set_affinity_hint for each MSIx vector to affiniate it
with calculated cpus at driver inilization time.
3. While freeing the MSIX vector, call this same API to release the cpu
affinity mask for each MSIx vector by providing the NULL value in
cpumask argument.
4. then call the free_cpumask_var API to free the memory allocated in step 2.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Copyright, Trademark & Confidentiality legal statements throughout the
source code changed from LSI to Avago.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For any SCSI command, if the driver receives IOC status =
SCSI_IOC_TERMINATED and log info = 0x32010081 then that command will be
completed with DID_RESET host status.
The definition of this log info value is "Virtual IO has failed and has
to be retried".
Firmware will provide this log info value with IOC Status
"SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume)
is pulled and pushed back within some minimal delay. With this log info
value, firmware informs the driver to retry the failed IO command
infinite times, so to provide some time for the firmware to discover
the reinserted drive successfully instated of just retrying failed
command for five times( doesn't giving enough time for firmware to
complete the drive discovery) and failing the IO permanently even
though drive came back successfully.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Change Set:
1. Extended the upper boundary restriction for the module parameter
max_sgl_entries. Earlier, the max_sgl_entries was capped at the
SCSI_MAX_SG_SEGMENTS kernel definition. With this change, the user
would be able to set the max_sgl_entries to any value which is
greater than SCSI_MAX_SG_SEGMENTS and less than the minimum of
SCSI_MAX_SG_CHAIN_SEGMENTS & hardware limit (Calculated using
IOCFacts's MaxChainDepth).
2. Added a print for the message log whenever the user sets the
max_sgl_entries to a value greater than SCSI_MAX_SG_SEGMENTS to
warn about the kernel definition overriding.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Change List in this MPI2 specification,
1. Added SSUTimeout field to MPI2_CONFIG_PAGE_BIOS_1,
and more defines for the BiosOptions field.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump driver version to 19.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When a flaky disk is there in a topology then during driver load,
discovery related I/O times out; which results in SCSI error recovery
initiating host reset and then the controller won't see any disk.
In this patch, The driver would return FAILED status to the host reset
initiated due to discovery related I/O timeout if ioc->is_driver_loading
is set. This flag would be set until we exit out of scsih_scan_finished().
i.e.
During device discovery if one of the disk is flaky
(which responds to some discovery commands and doesn't respond to some)
the driver wouldn't perform host reset for discovery related I/O timeout.
Instead it would return Failure for the host reset resulting in the
flaky disk getting removed by the SCSI Mid layer,
so other disks would be added correctly.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch will log a message when driver receives "Temperature Threshold
exceeded" event from any temperature sensor.
The message will look similar to like:
mpt3sas0: Temperature Threshold flags a b c d exceeded for Sensor: x !!!
mpt3sas0: Current Temp In Celsius: y
where a b c d are threshold flags 0 1 2 3
Change_set:
1. Get the number of sensor count of this IOC by reading IO Unit page 8 at
driver initialization time.
2. Also unmask the Temperature Threshold Event at driver initialization
time
3. Whenever a MPI2_EVENT_TEMP_THRESHOLD event is received from the
firmware, then print the sensor number, the maximum threshold number it
has exceed and the current temperature of this sensor.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Below is the changeset from the MPI specification and 2.00.34 header
files:
1) Defined additional bits in the BiosOptions field of BIOS Page 1 to
allow for finer control of X86 BIOS and UEFI BSD.
2) For the Clean Tool, reserved bit 26 of the Flags field for product
specific use.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Robert Elliott