Commit Graph

348979 Commits

Author SHA1 Message Date
Kamil Debski 33133ea7ac [media] s5p-mfc: Fix a watchdog bug
Fixed wrong condition in firmware reload function used by the watchdog.

Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 17:27:19 -02:00
Hans Verkuil ba1066d2e9 [media] tuner-core: map audmode to STEREO for radio devices
Fixes a v4l2-compliance error: setting audmode to a value other than mono
or stereo for a radio device should map to MODE_STEREO.
The spec specifies that for radio devices only mono and stereo audmodes are
valid. If the user specifies another audmode in v4l2_tuner, then that should
be mapped to valid audmode. That didn't happen here.
Note that tuner drivers might decide to limit the possible audmode even
further if it only supports mono. In that case the tuner driver can set
audmode to mono. However, that new value wasn't copied back to t->audmode,
and that has been fixed as well in this patch.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 16:55:38 -02:00
Sylwester Nawrocki 84a15ded76 [media] V4L: Add driver for OV9650/52 image sensors
This patch adds V4L2 sub-device driver for OV9650/OV9652 image sensors.
The driver exposes following V4L2 controls:
- auto/manual exposure,
- auto/manual white balance,
- auto/manual gain,
- brightness, saturation, sharpness,
- horizontal/vertical flip,
- color bar test pattern,
- banding filter (power line frequency).
Frame rate can be configured with g/s_frame_interval pad level ops.
Supported resolution are only: SXGA, VGA, QVGA.

Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 15:21:15 -02:00
Sylwester Nawrocki ffa9b9f016 [media] V4L: Add v4l2_ctrl_subdev_log_status() helper function
This patch adds a v4l2 core helper function that can be used as
the log_status handler for subdevs that only need to log state
of the v4l2 controls owned by the subdev's control handler.

Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 15:17:16 -02:00
Sylwester Nawrocki 22fa4279ee [media] V4L: Add v4l2_ctrl_subdev_subscribe_event() helper function
Add a v4l2 core helper function that can be used as the subdev
.subscribe_event handler. This allows to eliminate some boilerplate
from drivers that are only handling the control events.

Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 15:05:26 -02:00
Sylwester Nawrocki 4f4d14b70a [media] V4L: Add v4l2_event_subdev_unsubscribe() helper function
Add a v4l2 core helper function that can be used as the subdev
.unsubscribe_event handler. This allows to eliminate some
boilerplate from drivers that are only handling the control events.

Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 15:04:55 -02:00
Sylwester Nawrocki 2ccbe779bc [media] v4l2-ctrl: Add helper function for the controls range update
This patch adds a helper function that allows to modify range,
i.e. minimum, maximum, step and default value of a v4l2 control,
after the control has been created and initialized. This is helpful
in situations when range of a control depends on user configurable
parameters, e.g. camera sensor absolute exposure time depending on
an output image resolution and frame rate.
v4l2_ctrl_modify_range() function allows to modify range of an
INTEGER, BOOL, MENU, INTEGER_MENU and BITMASK type controls.
Based on a patch from Hans Verkuil http://patchwork.linuxtv.org/patch/8654.

Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 15:04:06 -02:00
Sylwester Nawrocki af9bb33aa3 [media] V4L: Add header file defining standard image sizes
Add common header file defining standard image sizes, so we can
avoid redefining those in each driver.

Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:59:41 -02:00
Hans de Goede f192747955 [media] pwc: Don't return EINVAL when an unsupported pixelformat is requested
Instead chaneg the passed in format to the pwc default pixelformat.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:47 -02:00
Peter Senna Tschudin 78f968fa26 [media] usb/gspca/zc3xx.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:43 -02:00
Peter Senna Tschudin e32d6eb865 [media] usb/gspca/xirlink_cit.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:40 -02:00
Peter Senna Tschudin f8d2687963 [media] usb/gspca/t613.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:37 -02:00
Peter Senna Tschudin 00ddb70702 [media] usb/gspca/stv06xx/stv06xx.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:34 -02:00
Peter Senna Tschudin 60d2156378 [media] usb/gspca/spca561.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:31 -02:00
Peter Senna Tschudin f11ef42e31 [media] usb/gspca/sonixj.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:27 -02:00
Peter Senna Tschudin f5b6de9cf6 [media] usb/gspca/sonixb.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Also replaced:
 #if !defined CONFIG_USB_SN9C102 && !defined CONFIG_USB_SN9C102_MODULE
with:
 #if !IS_ENABLED(CONFIG_USB_SN9C102)

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:24 -02:00
Peter Senna Tschudin 8099affaa6 [media] usb/gspca/sn9c20x.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:22 -02:00
Peter Senna Tschudin 5fd30838da [media] usb/gspca/se401.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:10 -02:00
Peter Senna Tschudin 2d622e9137 [media] usb/gspca/pac7311.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:07 -02:00
Peter Senna Tschudin ae814c0845 [media] gspca/pac7302.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:54:04 -02:00
Peter Senna Tschudin 4f4d178535 [media] usb/gspca/pac207.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:53:58 -02:00
Peter Senna Tschudin c4ea799a2b [media] usb/gspca/ov519.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:53:54 -02:00
Peter Senna Tschudin 9bc0446331 [media] usb/gspca/konica.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:53:48 -02:00
Peter Senna Tschudin 13a00fabe4 [media] usb/gspca: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:53:39 -02:00
Peter Senna Tschudin a3f6ce6345 [media] usb/gspca/cpia1.c: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:53:14 -02:00
Peter Senna Tschudin 480d3ca13e [media] radio/si470x/radio-si470x.h: use IS_ENABLED() macro
replace:
 #if defined(CONFIG_USB_SI470X) || \
     defined(CONFIG_USB_SI470X_MODULE)
with:
 #if IS_ENABLED(CONFIG_USB_SI470X)
This change was made for: CONFIG_USB_SI470X,
CONFIG_I2C_SI470X

Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:52:46 -02:00
Johannes Schellen 58bc8b7e38 [media] omap3isp: Fix histogram regions
This patch fixes a bug which causes all histogram regions to start in the
top left corner of the image. The histogram region coordinates are 16 bit
values which share a 32 bit register. The bug is due to the region end
value assignments overwriting the region start values with zero.

Signed-off-by: Johannes Schellen <Johannes.Schellen@rwth-aachen.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:50:49 -02:00
Laurent Pinchart cf2b4cf661 [media] omap3isp: Use devm_* managed functions
Replace kzalloc, request_mem_region, ioremap, clk_get and regulator_get
with their devm_* managed replacement.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:49:17 -02:00
Laurent Pinchart 3d5a71ef32 [media] omap3isp: Remove unneeded memset after kzalloc
kzalloc initializes the memory it allocates to 0, there's no need for an
explicit memset.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:48:13 -02:00
Laurent Pinchart 3fdfedaaa7 [media] omap3isp: preview: Lower the crop margins
The preview engine includes filters that consume columns and lines as
part of their operation, thus resulting in a cropped image. To allow
turning those filters on/off during streaming without affecting the
output image size, the driver adds additional cropping to make the total
number of cropped columns and lines constant regardless of which filters
are enabled.
This process needlessly includes the CFA filter, as whether the filter
is enabled only depends on the sink pad format, which can't change
during streaming.
Exclude the CFA filter from the preview engine margins.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:45:29 -02:00
Oliver Neukum a82a45f653 [media] uvcvideo: Fix race of open and suspend in error case
Ming Lei reported:
IMO, there is a minor fault in the error handling path of
uvc_status_start() inside uvc_v4l2_open(), and the 'users' count should
have been decreased before usb_autopm_put_interface(). In theory, a [URB
resubmission] warning can be triggered when the device is opened just
between usb_autopm_put_interface() and atomic_dec(&stream->dev->users).
The fix is trivial.

Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:32:21 -02:00
Ezequiel Garcia 8c0d44e250 [media] uvcvideo: Replace memcpy with struct assignment
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:31:36 -02:00
Wei Yongjun 5d97046a37 [media] davinci: vpbe: fix missing unlock on error in vpbe_initialize()
Add the missing unlock on the error handling path in function
vpbe_initialize().

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:26:08 -02:00
Lad, Prabhakar b9f1fbcd0e [media] davinci: dm355: Fix uninitialized variable compiler warnings
drivers/media/platform/davinci/dm355_ccdc.c:593:9: warning: ‘val1’ may be
used uninitialized in this function [-Wuninitialized]
drivers/media/platform/davinci/dm355_ccdc.c:560:6: note: ‘val1’ was declared here
This is a false positive but the compiler has no way to know about it,
so initialize the variable to 0.

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:09:55 -02:00
Lad, Prabhakar c7a857a09f [media] adv7343: use devm_kzalloc() instead of kzalloc()
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:08:54 -02:00
Lad, Prabhakar 08754d3185 [media] tvp514x: use devm_kzalloc() instead of kzalloc()
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:08:25 -02:00
Lad, Prabhakar f3e8e4f1c0 [media] tvp7002: use devm_kzalloc() instead of kzalloc()
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:08:04 -02:00
Lad, Prabhakar d41d81983a [media] ths7303: use devm_kzalloc() instead of kzalloc()
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.

Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 14:05:06 -02:00
Paul Bolle b4c13d3df1 [media] saa7164: silence GCC warnings
Compiling the saa7164 driver without CONFIG_VIDEO_ADV_DEBUG set triggers
these GCC warnings:
    drivers/media/pci/saa7164/saa7164-encoder.c:1301:12: warning: ‘saa7164_g_register’ defined but not used [-Wunused-function]
    drivers/media/pci/saa7164/saa7164-encoder.c:1314:12: warning: ‘saa7164_s_register’ defined but not used [-Wunused-function]
Silence these warnings by wrapping these two functions in an "#ifdef
CONFIG_VIDEO_ADV_DEBUG" and "#endif" pair.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-05 13:50:14 -02:00
Alexandre Lissy 24dec5dabf [media] imon: fix Knob event interpretation issues on ARM
Events for the iMon Knob pad where not correctly interpreted on ARM,
resulting in buggy mouse movements (cursor going straight out of the
screen), key pad only generating KEY_RIGHT and KEY_DOWN events.
A reproducer is:
int main(int argc, char ** argv)
{
        char rel_x = 0x00; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
        rel_x = 0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
        rel_x |= ~0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
        return 0;
}
(running on x86 or amd64)
$ ./test
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:-1 @test.c:8
(running on armv6)
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:255 @test.c:8
Forcing the rel_x and rel_y variables as signed char fixes the issue.

Reference: http://www.arm.linux.org.uk/docs/faqs/signedchar.php

Signed-off-by: Alexandre Lissy <alexandrelissy@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-02-01 07:13:59 -02:00
Mauro Carvalho Chehab a32f7d1ad3 Merge branch 'v4l_for_linus' into staging/for_v3.9
* v4l_for_linus: (464 commits)
  [media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
  [media] uvcvideo: Cleanup leftovers of partial revert
  [media] uvcvideo: Return -EACCES when trying to set a read-only control
  Linux 3.8-rc3
  mm: reinstante dropped pmd_trans_splitting() check
  cred: Remove tgcred pointer from struct cred
  drm/ttm: fix fence locking in ttm_buffer_object_transfer
  ARM: clps711x: Fix bad merge of clockevents setup
  ARM: highbank: save and restore L2 cache and GIC on suspend
  ARM: highbank: add a power request clear
  ARM: highbank: fix secondary boot and hotplug
  ARM: highbank: fix typos with hignbank in power request functions
  ARM: dts: fix highbank cpu mpidr values
  ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
  drm/prime: drop reference on imported dma-buf come from gem
  xen/netfront: improve truesize tracking
  ARM: mx5: Fix MX53 flexcan2 clock
  ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
  sctp: fix Kconfig bug in default cookie hmac selection
  EDAC: Cleanup device deregistering path
  ...

Conflicts:
	drivers/media/pci/dm1105/dm1105.c
	drivers/media/platform/soc_camera/mx2_camera.c
2013-01-24 18:49:18 -02:00
Andreas Regel 6b9e50c463 [media] stv090x: On STV0903 do not set registers of the second path
Sometimes there is a problem when trying to access the non-existing registers
of the second demodulator path on the STV0903.

This change removes the calls in case the driver is used on a STV0903.

Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-24 18:31:00 -02:00
Mauro Carvalho Chehab f67102c49a [media] mb86a20s: remove global BER/PER counters if per-layer counters vanish
If, for any reason, all per-layers counters stop, remove the
corresponding global counter.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-24 14:28:32 -02:00
Mauro Carvalho Chehab d9b6f08a7f [media] mb86a20s: add a logic for post-BER measurement
The logic here is similar to the preBER.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-24 14:28:14 -02:00
Mauro Carvalho Chehab 313cf4efa4 [media] mb86a20s: fix the PER reset logic
The logic that resets the device is wrong. It should be resetting
just the layer that got read. Also, stop is needed before updating
the counters.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-24 14:27:16 -02:00
Mauro Carvalho Chehab ad0abbf118 [media] mb86a20s: some fixes at preBER logic
The logic that resets the device is wrong. It should be resetting
just the layer that got read. Also, stop is needed before updating
the counters.
While there, rename it, as we'll soon introduce a postBER logic
there.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-24 14:26:55 -02:00
Mauro Carvalho Chehab 593ae89a3f [media] mb86a20s: add block count measures (PER/UCB)
Add both per-layer and global block error count and block count,
for PER and UCB measurements.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-24 14:24:59 -02:00
Mauro Carvalho Chehab 94a93e5f85 [media] dvb_frontend: print a msg if a property doesn't exist
If userspace calls a property that doesn't exist, it currently
just returns -EINVAL. However, this is more likely a problem at
the userspace application, calling it with a non-existing property.
So, add a debug message to help tracking it.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-23 19:10:57 -02:00
Mauro Carvalho Chehab 25188bd0e6 [media] mb86a20s: add CNR measurement
Add Signal/Noise ratio measurement. On this device, a global measure
is taken by the demod. It also provides per-layer CNR measurements,
based on Modulation Error measures (MER).

Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-23 19:10:49 -02:00
Mauro Carvalho Chehab d01a8ee37a [media] mb86a20s: improve bit error count for BER
Do a better job on setting the bit error counters, in order to
have all layer measures to happen in a little less than one
second.

Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2013-01-23 19:10:42 -02:00