Pull networking fixes from David Miller:
"It looks like a decent sized set of fixes, but a lot of these are one
liner off-by-one and similar type changes:
1) Fix netlink header pointer to calcular bad attribute offset
reported to user. From Pablo Neira Ayuso.
2) Don't double clear PHY interrupts when ->did_interrupt is set,
from Heiner Kallweit.
3) Add missing validation of various (devlink, nl802154, fib, etc.)
attributes, from Jakub Kicinski.
4) Missing *pos increments in various netfilter seq_next ops, from
Vasily Averin.
5) Missing break in of_mdiobus_register() loop, from Dajun Jin.
6) Don't double bump tx_dropped in veth driver, from Jiang Lidong.
7) Work around FMAN erratum A050385, from Madalin Bucur.
8) Make sure ARP header is pulled early enough in bonding driver,
from Eric Dumazet.
9) Do a cond_resched() during multicast processing of ipvlan and
macvlan, from Mahesh Bandewar.
10) Don't attach cgroups to unrelated sockets when in interrupt
context, from Shakeel Butt.
11) Fix tpacket ring state management when encountering unknown GSO
types. From Willem de Bruijn.
12) Fix MDIO bus PHY resume by checking mdio_bus_phy_may_suspend()
only in the suspend context. From Heiner Kallweit"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
net: systemport: fix index check to avoid an array out of bounds access
tc-testing: add ETS scheduler to tdc build configuration
net: phy: fix MDIO bus PM PHY resuming
net: hns3: clear port base VLAN when unload PF
net: hns3: fix RMW issue for VLAN filter switch
net: hns3: fix VF VLAN table entries inconsistent issue
net: hns3: fix "tc qdisc del" failed issue
taprio: Fix sending packets without dequeueing them
net: mvmdio: avoid error message for optional IRQ
net: dsa: mv88e6xxx: Add missing mask of ATU occupancy register
net: memcg: fix lockdep splat in inet_csk_accept()
s390/qeth: implement smarter resizing of the RX buffer pool
s390/qeth: refactor buffer pool code
s390/qeth: use page pointers to manage RX buffer pool
seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol number
net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed
net/packet: tpacket_rcv: do not increment ring index on drop
sxgbe: Fix off by one in samsung driver strncpy size arg
net: caif: Add lockdep expression to RCU traversal primitive
MAINTAINERS: remove Sathya Perla as Emulex NIC maintainer
...
add CONFIG_NET_SCH_ETS to 'config', otherwise test suites using this file
to perform a full tdc run will encounter the following warning:
ok 645 e90e - Add ETS qdisc using bands # skipped - "-----> teardown stage" did not complete successfully
Fixes: 82c664b69c ("selftests: qdiscs: Add test coverage for ETS Qdisc")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xas_for_each_marked() is using entry == NULL as a termination condition
of the iteration. When xas_for_each_marked() is used protected only by
RCU, this can however race with xas_store(xas, NULL) in the following
way:
TASK1 TASK2
page_cache_delete() find_get_pages_range_tag()
xas_for_each_marked()
xas_find_marked()
off = xas_find_chunk()
xas_store(&xas, NULL)
xas_init_marks(&xas);
...
rcu_assign_pointer(*slot, NULL);
entry = xa_entry(off);
And thus xas_for_each_marked() terminates prematurely possibly leading
to missed entries in the iteration (translating to missing writeback of
some pages or a similar problem).
If we find a NULL entry that has been marked, skip it (unless we're trying
to allocate an entry).
Reported-by: Jan Kara <jack@suse.cz>
CC: stable@vger.kernel.org
Fixes: ef8e5717db ("page cache: Convert delete_batch to XArray")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
This commit adds a test to check if we can fully utilize 4-tuples for
connect() when all ephemeral ports are exhausted.
The test program changes the local port range to use only one port and binds
two sockets with or without SO_REUSEADDR and SO_REUSEPORT, and with the same
EUID or with different EUIDs, then do listen().
We should be able to bind only one socket having both SO_REUSEADDR and
SO_REUSEPORT per EUID, which restriction is to prevent unintentional
listen().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
allows to run the tests with fixed receive buffer by passing
"-R <value>" to mptcp_connect.sh.
While at it, add a default 10 second poll timeout so the "-t"
becomes optional -- this makes mptcp_connect simpler to use
during manual testing.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Make the default option oldconfig instead of randconfig
(one too many times I lost my config because I left the build type out)
- Add timeout to ssh sync to sync before reboot (prevents test hangs)
- A couple of spelling fix patches
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXmakcxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhLKAP9eEZxg0HzIXo3mn9ECcpLaJIKgXGCY
Q55z1dN56qliZQD+KcRAB0kA2oxP0tBsJyTrizpJnkldkNrbRd4uJZo/4gA=
=sn+K
-----END PGP SIGNATURE-----
Merge tag 'ktest-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull Ktest fixes and clean ups from Steven Rostedt:
- Make the default option oldconfig instead of randconfig (one too many
times I lost my config because I left the build type out)
- Add timeout to ssh sync to sync before reboot (prevents test hangs)
- A couple of spelling fix patches
* tag 'ktest-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Fix typos in ktest.pl
ktest: Add timeout for ssh sync testing
ktest: Make default build option oldconfig not randconfig
ktest: Fix some typos in sample.conf
Remove the guard that disables UDP tests now that sockmap
has support for them.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-12-lmb@cloudflare.com
Expand the TCP sockmap test suite to also check UDP sockets.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-11-lmb@cloudflare.com
Most tests for TCP sockmap can be adapted to UDP sockmap if the
listen call is skipped. Rename listen_loopback, etc. to socket_loopback
and skip listen() for SOCK_DGRAM.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200309111243.6982-10-lmb@cloudflare.com
This patch fixes multipe spelling typo found in ktest.pl.
Link: http://lkml.kernel.org/r/20200309115430.57540-1-standby24x7@gmail.com
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Before rebooting the box, a "ssh sync" is called to the test machine to see
if it is alive or not. But if the test machine is in a partial state, that
ssh may never actually finish, and the ktest test hangs.
Add a 10 second timeout to the sync test, which will fail after 10 seconds
and then cause the test to reboot the test machine.
Cc: stable@vger.kernel.org
Fixes: 6474ace999 ("ktest.pl: Powercycle the box on reboot if no connection can be made")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
For the last time, I screwed up my ktest config file, and the build went
into the default "randconfig", blowing away the .config that I had set up.
The reason for the default randconfig was because when this was first
written, I wanted to do a bunch of randconfigs. But as time progressed,
ktest isn't about randconfig anymore, and because randconfig destroys the
config in the build directory, it's a dangerous default to have. Use
oldconfig as the default.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This patch fixes some spelling typo in sample.conf
Link: http://lkml.kernel.org/r/20190930124925.20250-1-standby24x7@gmail.com
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXmNvpgAKCRCRxhvAZXjc
ouFvAQDCzfOx1vcEP/nNhYBP2MPuafKclJcoJggC9rSmIvcLiQD/TI+LyHzplD+m
MWSu9NZJ6h6qyjKJivja3/bs8DVEewU=
=4gyS
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2020-03-07' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux
Pull thread fixes from Christian Brauner:
"Here are a few hopefully uncontroversial fixes:
- Use RCU_INIT_POINTER() when initializing rcu protected members in
task_struct to fix sparse warnings.
- Add pidfd_fdinfo_test binary to .gitignore file"
* tag 'for-linus-2020-03-07' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
selftests: pidfd: Add pidfd_fdinfo_test in .gitignore
exit: Fix Sparse errors and warnings
fork: Use RCU_INIT_POINTER() instead of rcu_access_pointer()
This Kselftest update for Linux 5.6-rc5 consists of a cleanup patch
to undo changes to global .gitignore that added selftests/lkdtm
objects and add them to a local selftests/lkdtm/.gitignore.
Summary of Linus's comments on local vs. global gitignore scope:
- Keep local gitignore patterns in local files.
- Put only global gitignore patterns in the top-level gitignore file.
Local scope keeps things much better separated. It also incidentally
means that if a directory gets renamed, the gitignore file continues
to work unless in the case of renaming the actual files themselves that
are named in the gitignore.
-----BEGIN PGP SIGNATURE-----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=8sYZ
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest update from Shuah Khan:
"This consists of a cleanup patch to undo changes to global .gitignore
that added selftests/lkdtm objects and add them to a local
selftests/lkdtm/.gitignore.
Summary of Linus's comments on local vs. global gitignore scope:
- Keep local gitignore patterns in local files.
- Put only global gitignore patterns in the top-level gitignore file.
Local scope keeps things much better separated. It also incidentally
means that if a directory gets renamed, the gitignore file continues
to work unless in the case of renaming the actual files themselves
that are named in the gitignore"
* tag 'linux-kselftest-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftest/lkdtm: Use local .gitignore
The existing tests attempt to check that JMP32 JSET ignores the upper
bits in the operand registers. However, the tests missed one such bug in
the x32 JIT that is only uncovered when a previous instruction pollutes
the upper 32 bits of the registers.
This patch adds a new test case that catches the bug by first executing
a 64-bit JSET to pollute the upper 32-bits of the temporary registers,
followed by a 32-bit JSET which should ignore the upper 32 bits.
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200305234416.31597-2-luke.r.nels@gmail.com
Currently the SW-datapath ETS selftests use "ip link" stats to obtain the
number of packets that went through a given band. mlxsw then uses ethtool
per-priority counters.
Instead, change both to use qdiscs. In SW datapath this is the obvious
choice, and now that mlxsw offloads FIFO, this should work on the offloaded
datapath as well. This has the effect of verifying that the FIFO offload
works.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added one test, send_signal_sched_switch, to test bpf_send_signal()
helper triggered by sched/sched_switch tracepoint. This test can be used
to verify kernel deadlocks fixed by the previous commit. The test itself
is heavily borrowed from Commit eac9153f2b ("bpf/stackmap: Fix deadlock
with rq_lock in bpf_get_stack()").
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200304191105.2796601-1-yhs@fb.com
The restriction introduced in 7a0df7fbc1 ("seccomp: Make NEW_LISTENER and
TSYNC flags exclusive") is mostly artificial: there is enough information
in a seccomp user notification to tell which thread triggered a
notification. The reason it was introduced is because TSYNC makes the
syscall return a thread-id on failure, and NEW_LISTENER returns an fd, and
there's no way to distinguish between these two cases (well, I suppose the
caller could check all fds it has, then do the syscall, and if the return
value was an fd that already existed, then it must be a thread id, but
bleh).
Matthew would like to use these two flags together in the Chrome sandbox
which wants to use TSYNC for video drivers and NEW_LISTENER to proxy
syscalls.
So, let's fix this ugliness by adding another flag, TSYNC_ESRCH, which
tells the kernel to just return -ESRCH on a TSYNC error. This way,
NEW_LISTENER (and any subsequent seccomp() commands that want to return
positive values) don't conflict with each other.
Suggested-by: Matthew Denton <mpdenton@google.com>
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Link: https://lore.kernel.org/r/20200304180517.23867-1-tycho@tycho.ws
Signed-off-by: Kees Cook <keescook@chromium.org>
Test for two scenarios:
* When the fmod_ret program returns 0, the original function should
be called along with fentry and fexit programs.
* When the fmod_ret program returns a non-zero value, the original
function should not be called, no side effect should be observed and
fentry and fexit programs should be called.
The result from the kernel function call and whether a side-effect is
observed is returned via the retval attr of the BPF_PROG_TEST_RUN (bpf)
syscall.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200304191853.1529-8-kpsingh@chromium.org
The current fexit and fentry tests rely on a different program to
exercise the functions they attach to. Instead of doing this, implement
the test operations for tracing which will also be used for
BPF_MODIFY_RETURN in a subsequent patch.
Also, clean up the fexit test to use the generated skeleton.
Signed-off-by: KP Singh <kpsingh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200304191853.1529-7-kpsingh@chromium.org
Add detection of out-of-tree built vmlinux image for the purpose of
VMLINUX_BTF detection. According to Documentation/kbuild/kbuild.rst, O takes
precedence over KBUILD_OUTPUT.
Also ensure ~/path/to/build/dir also works by relying on wildcard's resolution
first, but then applying $(abspath) at the end to also handle
O=../../whatever cases.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200304184336.165766-1-andriin@fb.com
Currently, BTF_KIND_ENUM type doesn't record whether enum values should be
interpreted as signed or unsigned. In Linux, most enums are unsigned, though,
so interpreting them as unsigned matches real world better.
Change btf_dump test case to test maximum 32-bit value, instead of negative
value.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200303003233.3496043-3-andriin@fb.com
Instead of hand-coding the busywait() predicate, use the until_counter_is()
introduced recently.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A function busywait() was recently added based on the logic in
__tc_check_packets(). Convert the code in tc_common to use the new
function.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
until_counter_is() currently takes as an argument a number and the
condition holds when the current counter value is >= that number. Make the
function more generic by taking a partial expression instead of just the
number.
Convert the two existing users.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tc_rule_stats_get() fetches a given statistic of a TC rule
given the rule preference. Another common way to reference a rule is using
its handle. Introduce a dual to the aforementioned function that gets a
statistic given rule handle.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch update {ipv4, ipv6}_addr_metric_test with
1. Set metric of address with peer route and see if the route added
correctly.
2. Modify metric and peer address for peer route and see if the route
changed correctly.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cgroup selftests did not declare the bpf_log_buf variable as static, leading
to a linker error with GCC 10 (which defaults to -fno-common). Fix this by
adding the missing static declarations.
Fixes: 257c88559f ("selftests/bpf: Convert test_cgroup_attach to prog_tests")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrey Ignatov <rdna@fb.com>
Link: https://lore.kernel.org/bpf/20200302145348.559177-1-toke@redhat.com
Move BPF_PROG, BPF_KPROBE, and BPF_KRETPROBE macro into libbpf's bpf_tracing.h
header to make it available for non-selftests users.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200229231112.1240137-5-andriin@fb.com
For kretprobes, there is no point in capturing input arguments from pt_regs,
as they are going to be, most probably, clobbered by the time probed kernel
function returns. So switch BPF_KRETPROBE to accept zero or one argument
(optional return result).
Fixes: ac065870d9 ("selftests/bpf: Add BPF_PROG, BPF_KPROBE, and BPF_KRETPROBE macros")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200229231112.1240137-4-andriin@fb.com
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-02-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 41 non-merge commits during the last 7 day(s) which contain
a total of 49 files changed, 1383 insertions(+), 499 deletions(-).
The main changes are:
1) BPF and Real-Time nicely co-exist.
2) bpftool feature improvements.
3) retrieve bpf_sk_storage via INET_DIAG.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix leak in nl80211 AP start where we leak the ACL memory, from
Johannes Berg.
2) Fix double mutex unlock in mac80211, from Andrei Otcheretianski.
3) Fix RCU stall in ipset, from Jozsef Kadlecsik.
4) Fix devlink locking in devlink_dpipe_table_register, from Madhuparna
Bhowmik.
5) Fix race causing TX hang in ll_temac, from Esben Haabendal.
6) Stale eth hdr pointer in br_dev_xmit(), from Nikolay Aleksandrov.
7) Fix TX hash calculation bounds checking wrt. tc rules, from Amritha
Nambiar.
8) Size netlink responses properly in schedule action code to take into
consideration TCA_ACT_FLAGS. From Jiri Pirko.
9) Fix firmware paths for mscc PHY driver, from Antoine Tenart.
10) Don't register stmmac notifier multiple times, from Aaro Koskinen.
11) Various rmnet bug fixes, from Taehee Yoo.
12) Fix vsock deadlock in vsock transport release, from Stefano
Garzarella.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
net: dsa: mv88e6xxx: Fix masking of egress port
mlxsw: pci: Wait longer before accessing the device after reset
sfc: fix timestamp reconstruction at 16-bit rollover points
vsock: fix potential deadlock in transport->release()
unix: It's CONFIG_PROC_FS not CONFIG_PROCFS
net: rmnet: fix packet forwarding in rmnet bridge mode
net: rmnet: fix bridge mode bugs
net: rmnet: use upper/lower device infrastructure
net: rmnet: do not allow to change mux id if mux id is duplicated
net: rmnet: remove rcu_read_lock in rmnet_force_unassociate_device()
net: rmnet: fix suspicious RCU usage
net: rmnet: fix NULL pointer dereference in rmnet_changelink()
net: rmnet: fix NULL pointer dereference in rmnet_newlink()
net: phy: marvell: don't interpret PHY status unless resolved
mlx5: register lag notifier for init network namespace only
unix: define and set show_fdinfo only if procfs is enabled
hinic: fix a bug of rss configuration
hinic: fix a bug of setting hw_ioctxt
hinic: fix a irq affinity bug
net/smc: check for valid ib_client_data
...
The scale test for Spectrum-2 should be invoked for Spectrum-2 and
Spectrum-3. Add the appropriate device ID.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the test inserts X /32 routes and for each route it is
testing that a packet sent from the first host is received by the second
host, which is very time-consuming.
Instead only validate the offload flag of each route and get the same result.
Wait between the creation of the routes and the offload validation in
order to make sure that all the routes were successfully offloaded.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding a given number of flower rules for different IPv6
addresses, the test generates traffic and ensures that each packet is
received, which is time-consuming.
Instead, test the offload indication of the tc flower rules and reduce
the running time by half.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test the max shared buffer occupancy for port's pool and port's TC's (using
different types of packets).
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlxsw lib for common defines, helpers etc.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two devlink port helpers:
* devlink port get by netdev
* devlink cpu port get
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sanity check for devlink info command.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test physical ports' shared buffer configuration options using random
values related to a specific configuration option. There are 3
configuration options: pool, TC bind and portpool.
Each sub-test, test a different configuration option and random the related
values as the follow:
* For pools, pool's size will be randomized.
* For TC bind, pool number and threshold will be randomized.
* For portpools, threshold will be randomized.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rtnetlink test uses offload indication checks.
Use a busywait helper and wait until the offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vxlan test uses offload indication checks.
Use a busywait helper and wait until the offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Blackhole routes test uses offload indication checks.
Use busywait helper and wait until the routes offload indication is set or
fail if it reaches timeout.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test checks that packets are trapped when they should egress a
router interface (RIF) that has become disabled. This is a temporary
state in a RIF's deletion sequence.
Currently, the test deletes the RIF by flushing all the IP addresses
configured on the associated netdev (br0). However, this is racy, as
this also flushes all the routes pointing to the netdev and if the
routes are deleted from the device before the RIF is disabled, then no
packets will try to egress the disabled RIF and the trap will not be
triggered.
Instead, trigger the deletion of the RIF by unlinking the mlxsw port
from the bridge that is backing the RIF. Unlike before, this will not
cause the kernel to delete the routes pointing to the bridge.
Note that due to current mlxsw locking scheme the RIF is always deleted
first, but this is going to change.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include test of forbidding to have multiple mirror actions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include test of forbidding to have redirect rule on egress-bound block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests that below the queue minimum length, there is no dropping /
marking, and above max, everything is dropped / marked.
The test is structured as a core file with topology and test code, and
three wrappers: one for RED used as a root Qdisc, and two for
testing (W)RED under PRIO and ETS.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract a helper __start_traffic() configurable by protocol type. Allow
passing through extra mausezahn arguments. Add a wrapper,
start_tcp_traffic().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The radix tree doesn't use alignment, so the argument was ignored.
The maple tree needs its nodes to be aligned, so we need to pay attention
to the alignment argument. Also change the types of 'size' and 'align'
to unsigned int to match commit f4957d5bd0.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
This Kselftest kunit update consists of fixes to documentation and
run-time tool from Brendan Higgins and Heidi Fahim.
-----BEGIN PGP SIGNATURE-----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=Q7Zl
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kunit fixes from Shuah Khan:
"This Kselftest kunit update consists of fixes to documentation and
the run-time tool from Brendan Higgins and Heidi Fahim"
* tag 'linux-kselftest-kunit-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: run kunit_tool from any directory
kunit: test: Improve error messages for kunit_tool when kunitconfig is invalid
Documentation: kunit: fixed sphinx error in code block
This Kselftest update for Linux 5.6-rc4 consists of:
- fixes to TIMEOUT failures and out-of-tree compilation compilation
errors from Michael Ellerman.
- Declutter git status fix from Christophe Leroy
-----BEGIN PGP SIGNATURE-----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=QRUz
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- fixes to TIMEOUT failures and out-of-tree compilation compilation
errors from Michael Ellerman.
- declutter git status fix from Christophe Leroy
* tag 'linux-kselftest-5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/rseq: Fix out-of-tree compilation
selftests: Install settings files to fix TIMEOUT failures
selftest/lkdtm: Don't pollute 'git status'
Add Python module with tests for "bpftool feature" command, which mainly
checks whether the "full" option is working properly.
Signed-off-by: Michal Rostecki <mrostecki@opensuse.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20200226165941.6379-6-mrostecki@opensuse.org
Add a specific test for the crash reported by Phil Sutter and addressed
in the previous patch. The test cases that, in my intention, should
have covered these cases, that is, the ones from the 'concurrency'
section, don't run these sequences tightly enough and spectacularly
failed to catch this.
While at it, define a convenient way to add these kind of tests, by
adding a "reported issues" test section.
It's more convenient, for this particular test, to execute the set
setup in its own function. However, future test cases like this one
might need to call setup functions, and will typically need no tools
other than nft, so allow for this in check_tools().
The original form of the reproducer used here was provided by Phil.
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Due to various bugs in tests clean up code (usually), if host system is
misconfigured, it happens that test_progs will just crash in the middle of
running a test with little to no indication of where and why the crash
happened. For cases where coredump is not readily available (e.g., inside
a CI), it's very helpful to have a stack trace, which lead to crash, to be
printed out. This change adds a signal handler that will capture and print out
symbolized backtrace:
$ sudo ./test_progs -t mmap
test_mmap:PASS:skel_open_and_load 0 nsec
test_mmap:PASS:bss_mmap 0 nsec
test_mmap:PASS:data_mmap 0 nsec
Caught signal #11!
Stack trace:
./test_progs(crash_handler+0x18)[0x42a888]
/lib64/libpthread.so.0(+0xf5d0)[0x7f2aab5175d0]
./test_progs(test_mmap+0x3c0)[0x41f0a0]
./test_progs(main+0x160)[0x407d10]
/lib64/libc.so.6(__libc_start_main+0xf5)[0x7f2aab15d3d5]
./test_progs[0x407ebc]
[1] 1988412 segmentation fault (core dumped) sudo ./test_progs -t mmap
Unfortunately, glibc's symbolization support is unable to symbolize static
functions, only global ones will be present in stack trace. But it's still a
step forward without adding extra libraries to get a better symbolization.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200225000847.3965188-1-andriin@fb.com
Extend existing devlink trap test to include metadata type for flow
action cookie.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before nftables commit fb9cea50e8b3 ("main: enforce options before
commands"), 'nft list ruleset -a' happened to work, but it's wrong
and won't work anymore. Replace it by 'nft -a list ruleset'.
Reported-by: Chen Yi <yiche@redhat.com>
Fixes: 611973c1e0 ("selftests: netfilter: Introduce tests for sets with range concatenation")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently we run SYN cookies test for all socket types and mark the test as
skipped if socket type is not compatible. This causes confusion because
skipped test might indicate a problem with the testing environment.
Instead, run the test only for the socket type which supports SYN cookies.
Also, switch to using designated initializers when setting up tests, so
that we can tweak only some test parameters, leaving the rest initialized
to default values.
Fixes: eecd618b45 ("selftests/bpf: Mark SYN cookie test skipped for UDP sockets")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200224135327.121542-2-jakub@cloudflare.com
SOCKMAP and SOCKHASH map types can be used with reuseport BPF programs but
don't support yet storing UDP sockets. Instead of marking UDP tests with
SOCK{MAP,HASH} as skipped, don't run them at all.
Skipped test might signal that the test environment is not suitable for
running the test, while in reality the functionality is not implemented in
the kernel yet.
Before:
sh# ./test_progs -t select_reuseport
…
#40 select_reuseport:OK
Summary: 1/126 PASSED, 30 SKIPPED, 0 FAILED
After:
sh# ./test_progs -t select_reuseport
…
#40 select_reuseport:OK
Summary: 1/98 PASSED, 2 SKIPPED, 0 FAILED
The remaining two skipped tests are SYN cookies tests, which will be
addressed in the subsequent patch.
Fixes: 11318ba8ca ("selftests/bpf: Extend SK_REUSEPORT tests to cover SOCKMAP/SOCKHASH")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200224135327.121542-1-jakub@cloudflare.com
Add a test to check functionality of ACL traps.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the helpers assume pref 1 and handle 101. Make that explicit
and pass the values from callers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include test of forbidding to have drop rule on mixed-bound
shared block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While userfaultfd, KVM's demand paging implementation, is not specific
to KVM, having a benchmark for its performance will be useful for
guiding performance improvements to KVM. As a first step towards creating
a userfaultfd demand paging test, create a simple memory access test,
based on dirty_log_test.
Reviewed-by: Oliver Upton <oupton@google.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Guests and hosts don't have to have the same page size. This means
calculations are necessary when selecting the number of guest pages
to allocate in order to ensure the number is compatible with the
host. Provide utilities to help with those calculations and apply
them where appropriate.
We also revert commit bffed38d4f ("kvm: selftests: aarch64:
dirty_log_test: fix unaligned memslot size") and then use
vm_adjust_num_guest_pages() there instead.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This array will allow us to easily translate modes to their parameter
values.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We're going to want this name in the library code, so use a shorter
name in the tests.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
BITS_PER_LONG and friends are provided by linux/bitops.h
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I'm not sure how we ended up using printf instead of fprintf in
virt_dump(). Fix it.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-02-21
The following pull-request contains BPF updates for your *net-next* tree.
We've added 25 non-merge commits during the last 4 day(s) which contain
a total of 33 files changed, 2433 insertions(+), 161 deletions(-).
The main changes are:
1) Allow for adding TCP listen sockets into sock_map/hash so they can be used
with reuseport BPF programs, from Jakub Sitnicki.
2) Add a new bpf_program__set_attach_target() helper for adding libbpf support
to specify the tracepoint/function dynamically, from Eelco Chaudron.
3) Add bpf_read_branch_records() BPF helper which helps use cases like profile
guided optimizations, from Daniel Xu.
4) Enable bpf_perf_event_read_value() in all tracing programs, from Song Liu.
5) Relax BTF mandatory check if only used for libbpf itself e.g. to process
BTF defined maps, from Andrii Nakryiko.
6) Move BPF selftests -mcpu compilation attribute from 'probe' to 'v3' as it has
been observed that former fails in envs with low memlock, from Yonghong Song.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that SOCKMAP and SOCKHASH map types can store listening sockets,
user-space and BPF API is open to a new set of potential pitfalls.
Exercise the map operations, with extra attention to code paths susceptible
to races between map ops and socket cloning, and BPF helpers that work with
SOCKMAP/SOCKHASH to gain confidence that all works as expected.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200218171023.844439-12-jakub@cloudflare.com
Parametrize the SK_REUSEPORT tests so that the map type for storing sockets
is not hard-coded in the test setup routine.
This, together with careful state cleaning after the tests, lets us run the
test cases for REUSEPORT_ARRAY, SOCKMAP, and SOCKHASH to have test coverage
for all supported map types. The last two support only TCP sockets at the
moment.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200218171023.844439-11-jakub@cloudflare.com
In order for sockmap/sockhash types to become generic collections for
storing TCP sockets we need to loosen the checks during map update, while
tightening the checks in redirect helpers.
Currently sock{map,hash} require the TCP socket to be in established state,
which prevents inserting listening sockets.
Change the update pre-checks so the socket can also be in listening state.
Since it doesn't make sense to redirect with sock{map,hash} to listening
sockets, add appropriate socket state checks to BPF redirect helpers too.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200218171023.844439-5-jakub@cloudflare.com
Pull networking fixes from David Miller:
1) Limit xt_hashlimit hash table size to avoid OOM or hung tasks, from
Cong Wang.
2) Fix deadlock in xsk by publishing global consumer pointers when NAPI
is finished, from Magnus Karlsson.
3) Set table field properly to RT_TABLE_COMPAT when necessary, from
Jethro Beekman.
4) NLA_STRING attributes are not necessary NULL terminated, deal wiht
that in IFLA_ALT_IFNAME. From Eric Dumazet.
5) Fix checksum handling in atlantic driver, from Dmitry Bezrukov.
6) Handle mtu==0 devices properly in wireguard, from Jason A.
Donenfeld.
7) Fix several lockdep warnings in bonding, from Taehee Yoo.
8) Fix cls_flower port blocking, from Jason Baron.
9) Sanitize internal map names in libbpf, from Toke Høiland-Jørgensen.
10) Fix RDMA race in qede driver, from Michal Kalderon.
11) Fix several false lockdep warnings by adding conditions to
list_for_each_entry_rcu(), from Madhuparna Bhowmik.
12) Fix sleep in atomic in mlx5 driver, from Huy Nguyen.
13) Fix potential deadlock in bpf_map_do_batch(), from Yonghong Song.
14) Hey, variables declared in switch statement before any case
statements are not initialized. I learn something every day. Get
rids of this stuff in several parts of the networking, from Kees
Cook.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits)
bnxt_en: Issue PCIe FLR in kdump kernel to cleanup pending DMAs.
bnxt_en: Improve device shutdown method.
net: netlink: cap max groups which will be considered in netlink_bind()
net: thunderx: workaround BGX TX Underflow issue
ionic: fix fw_status read
net: disable BRIDGE_NETFILTER by default
net: macb: Properly handle phylink on at91rm9200
s390/qeth: fix off-by-one in RX copybreak check
s390/qeth: don't warn for napi with 0 budget
s390/qeth: vnicc Fix EOPNOTSUPP precedence
openvswitch: Distribute switch variables for initialization
net: ip6_gre: Distribute switch variables for initialization
net: core: Distribute switch variables for initialization
udp: rehash on disconnect
net/tls: Fix to avoid gettig invalid tls record
bpf: Fix a potential deadlock with bpf_map_do_batch
bpf: Do not grab the bucket spinlock by default on htab batch ops
ice: Wait for VF to be reset/ready before configuration
ice: Don't tell the OS that link is going down
ice: Don't reject odd values of usecs set by user
...
The commits introducing 'mlock-random-test'[1], 'map_fiex_noreplace'[2],
and 'thuge-gen'[3] have not added those in the 'run_vmtests' script and
thus the 'run_tests' command of kselftests doesn't run those. This
commit adds those in the script.
'gup_benchmark' and 'transhuge-stress' are also not included in the
'run_vmtests', but this commit does not add those because those are for
performance measurement rather than pass/fail tests.
[1] commit 26b4224d99 ("selftests: expanding more mlock selftest")
[2] commit 91cbacc345 ("tools/testing/selftests/vm/map_fixed_noreplace.c: add test for MAP_FIXED_NOREPLACE")
[3] commit fcc1f2d5dd ("selftests: add a test program for variable huge page sizes in mmap/shmget")
Link: http://lkml.kernel.org/r/20200206085144.29126-1-sj38.park@gmail.com
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Libbpf's Travis CI tests caught this issue. Ensure bpf_link and bpf_object
clean up is performed correctly.
Fixes: d633d57902 ("selftest/bpf: Add test for allowed trampolines count")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20200220230546.769250-1-andriin@fb.com
Use the new bpf_program__set_attach_target() API in the xdp_bpf2bpf
selftest so it can be referenced as an example on how to use it.
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/158220520562.127661.14289388017034825841.stgit@xdp-tutorial
This commit enables the KCSAN Kconfig options that (1) detect data
races between reads and writes even when the writes do not change the
variable's value and (2) detect data races involving plain C-language
writes. These changes only affect scripted rcutorture runs and can be
overridden using the kvm.sh --kconfig argument.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Currently, kvm-find-errors.sh gives a usage prompt when given a bad
directory, but then soldiers on, giving a series of confusing error
messages. This commit therefore prints an error message and exits when
given a bad directory, hopefully reducing confusion.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
When running the default list of tests, the run summary of a successful
(that is, failed to find any errors) run fits easily on a 24-line screen.
But a run with something like "--configs '5*CFLIST'" will be 80 lines long,
and it is all too easy to miss a failure message when scrolling back.
This commit therefore prints out the number of runs with failing builds
or runtime failures, but only if there are any such failures.
For example, a run with a single build error and a single runtime error
would print two lines like this:
1 runs with build errors.
1 runs with runtime errors.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The small-system rcutorture configurations have served us well for a great
many years, but it is now time to add a larger one. This commit does
just that, but does not add it to the defaults in CFLIST. This allows
the kvm.sh argument '--configs "4*CFLIST TREE10" to run four instances
of each of the default configurations concurrently with one instance of
the large configuration.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The names of the per-test results directories are of the form
2019.11.29-20:42:19. This works, but the ":" characters make
tab-based shell name completion a bit onerous because the user must
remember to include a quote character somewhere before the first ":".
This commit therefore changes the ":" characters to periods, as in
2019.12.01-20.48.01", which allows tab-based completion to work more
naturally.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The bootparam_hotplug_cpu() bash function was checking for CPU-hotplug
kernel-boot parameters from --bootargs, but that check was specific to
rcutorture ("rcutorture\.onoff_"). This commit therefore makes this
check also work for locktorture ("torture\.onoff_").
Note that rcuperf does not do CPU-hotplug operations, so it is not
necessary to make a similar change for rcuperf.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Currently if you build with O=... the rseq tests don't build:
$ make O=$PWD/output -C tools/testing/selftests/ TARGETS=rseq
make: Entering directory '/linux/tools/testing/selftests'
...
make[1]: Entering directory '/linux/tools/testing/selftests/rseq'
gcc -O2 -Wall -g -I./ -I../../../../usr/include/ -L./ -Wl,-rpath=./ -shared -fPIC rseq.c -lpthread -o /linux/output/rseq/librseq.so
gcc -O2 -Wall -g -I./ -I../../../../usr/include/ -L./ -Wl,-rpath=./ basic_test.c -lpthread -lrseq -o /linux/output/rseq/basic_test
/usr/bin/ld: cannot find -lrseq
collect2: error: ld returned 1 exit status
This is because the library search path points to the source
directory, not the output.
We can fix it by changing the library search path to $(OUTPUT).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit 852c8cbf34 ("selftests/kselftest/runner.sh: Add 45 second
timeout per test") added a 45 second timeout for tests, and also added
a way for tests to customise the timeout via a settings file.
For example the ftrace tests take multiple minutes to run, so they
were given longer in commit b43e78f65b ("tracing/selftests: Turn off
timeout setting").
This works when the tests are run from the source tree. However if the
tests are installed with "make -C tools/testing/selftests install",
the settings files are not copied into the install directory. When the
tests are then run from the install directory the longer timeouts are
not applied and the tests timeout incorrectly.
So add the settings files to TEST_FILES of the appropriate Makefiles
to cause the settings files to be installed using the existing install
logic.
Fixes: 852c8cbf34 ("selftests/kselftest/runner.sh: Add 45 second timeout per test")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This Kselftest update for Linux 5.6-rc3 consists of fixes to build
failures and other test bugs.
-----BEGIN PGP SIGNATURE-----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=OFRu
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
"Fixes to build failures and other test bugs"
* tag 'linux-kselftest-5.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: openat2: fix build error on newer glibc
selftests: use LDLIBS for libraries instead of LDFLAGS
selftests: fix too long argument
selftests: allow detection of build failures
Kernel selftests: tpm2: check for tpm support
selftests/ftrace: Have pid filter test use instance flag
selftests: fix spelling mistaked "chaigned" -> "chained"
Alexei Starovoitov says:
====================
pull-request: bpf 2020-02-19
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 10 day(s) which contain
a total of 10 files changed, 93 insertions(+), 31 deletions(-).
The main changes are:
1) batched bpf hashtab fixes from Brian and Yonghong.
2) various selftests and libbpf fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Added tests for 'u32' extended match rules for u8 alignment.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The selftests fails to build with:
tools/testing/selftests/bpf/prog_tests/sockmap_ktls.c: In function ‘test_sockmap_ktls_disconnect_after_delete’:
tools/testing/selftests/bpf/prog_tests/sockmap_ktls.c:72:37: error: ‘TCP_ULP’ undeclared (first use in this function)
72 | err = setsockopt(cli, IPPROTO_TCP, TCP_ULP, "tls", strlen("tls"));
| ^~~~~~~
Similar to commit that fixes build of sockmap_basic.c on systems with old
/usr/include fix the build of sockmap_ktls.c
Fixes: d1ba1204f2 ("selftests/bpf: Test unhashing kTLS socket after removing from map")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200219205514.3353788-1-ast@kernel.org
The latest llvm supports cpu version v3, which is cpu version v1
plus some additional 64bit jmp insns and 32bit jmp insn support.
In selftests/bpf Makefile, the llvm flag -mcpu=probe did runtime
probe into the host system. Depending on compilation environments,
it is possible that runtime probe may fail, e.g., due to
memlock issue. This will cause generated code with cpu version v1.
This may cause confusion as the same compiler and the same C code
generates different byte codes in different environment.
Let us change the llvm flag -mcpu=probe to -mcpu=v3 so the
generated code will be the same regardless of the compilation
environment.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200219004236.2291125-1-yhs@fb.com
Add a selftest to test:
* default bpf_read_branch_records() behavior
* BPF_F_GET_BRANCH_RECORDS_SIZE flag behavior
* error path on non branch record perf events
* using helper to write to stack
* using helper to write to global
On host with hardware counter support:
# ./test_progs -t perf_branches
#27/1 perf_branches_hw:OK
#27/2 perf_branches_no_hw:OK
#27 perf_branches:OK
Summary: 1/2 PASSED, 0 SKIPPED, 0 FAILED
On host without hardware counter support (VM):
# ./test_progs -t perf_branches
#27/1 perf_branches_hw:OK
#27/2 perf_branches_no_hw:OK
#27 perf_branches:OK
Summary: 1/2 PASSED, 1 SKIPPED, 0 FAILED
Also sync tools/include/uapi/linux/bpf.h.
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200218030432.4600-3-dxu@dxuuu.xyz
Implemented small fix so that the script changes work directories to the
root of the linux kernel source tree from which kunit.py is run. This
enables the user to run kunit from any working directory. Originally
considered using os.path.join but this is more error prone as we would
have to find all file path usages and modify them accordingly. Using
os.chdir ensures that the entire script is run within /linux.
Signed-off-by: Heidi Fahim <heidifahim@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Previous error message for invalid kunitconfig was vague. Added to it so
that it lists invalid fields and prompts for them to be removed. Added
validate_config function returning whether or not this kconfig is valid.
Signed-off-by: Heidi Fahim <heidifahim@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
When a TCP socket gets inserted into a sockmap, its sk_prot callbacks get
replaced with tcp_bpf callbacks built from regular tcp callbacks. If TLS
gets enabled on the same socket, sk_prot callbacks get replaced once again,
this time with kTLS callbacks built from tcp_bpf callbacks.
Now, we allow removing a socket from a sockmap that has kTLS enabled. After
removal, socket remains with kTLS configured. This is where things things
get tricky.
Since the socket has a set of sk_prot callbacks that are a mix of kTLS and
tcp_bpf callbacks, we need to restore just the tcp_bpf callbacks to the
original ones. At the moment, it comes down to the the unhash operation.
We had a regression recently because tcp_bpf callbacks were not cleared in
this particular scenario of removing a kTLS socket from a sockmap. It got
fixed in commit 4da6a196f9 ("bpf: Sockmap/tls, during free we may call
tcp_bpf_unhash() in loop").
Add a test that triggers the regression so that we don't reintroduce it in
the future.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200217121530.754315-4-jakub@cloudflare.com
When a kernel is configured without CONFIG_DEV_DAX_PMEM_COMPAT, the
compilation of tools/testing/nvdimm fails with:
Building modules, stage 2.
MODPOST 11 modules
ERROR: "dax_pmem_compat_test" [tools/testing/nvdimm/test/nfit_test.ko] undefined!
Fix the problem by calling dax_pmem_compat_test() only if the kernel has
the required functionality.
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20200123154720.12097-1-jack@suse.cz
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
0x11 and 0x12 set the ECN bits based on RFC2474, it would be better to avoid
that. 0x14 and 0x18 would be better and works as well.
Reported-by: Petr Machata <petrm@mellanox.com>
Fixes: 4e867c9a50 ("selftests: forwarding: vxlan_bridge_1d: fix tos value")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when two VXLAN tunnels with conflicting configurations (i.e.,
different TTL) are enslaved to the same VLAN-aware bridge, then the
enslavement of a port to the bridge is denied.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes, the VXLAN tunnel will be offloaded regardless if
any local ports are member in the FID or not. Adjust the test to make
sure the tunnel is offloaded in this case.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver supports a single VLAN-aware bridge. Test that the
enslavement of a port to the second VLAN-aware bridge fails with an
extack.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that creation of a bridge (both VLAN-aware and VLAN-unaware) fails
with an extack when a VXLAN device with an unsupported configuration is
already enslaved to it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of a VLAN on a bridge slave prompts the driver to have the
local port in question join the FID corresponding to this VLAN.
Before recent changes, the operation of joining the FID would also mean
that the driver would enable VXLAN tunneling if a VXLAN device was also
member in the VLAN. In case the configuration of the VXLAN tunnel was
not supported, an extack error would be returned.
Since the operation of joining the FID no longer means that VXLAN
tunneling is potentially enabled, the test is no longer relevant. Remove
it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gives us fewer dependencies and shortens build time, fixes up some
hash checking race conditions, and also fixes missing directory creation
that caused issues on massively parallel builds.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever the server side of vsock is binding to the socket, but not
listening yet, we expect the behavior from the client to be identical to
what happens when the server is not even started.
This new test runs the server side so that it binds to the socket
without ever listening to it. The client side will try to connect and
should receive an ECONNRESET error.
This new test provides a way to validate the previously introduced patch
for making sure the server side will always answer with a RST packet in
case the client requested a new connection.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 71130f2997 ("vxlan: fix tos value before xmit") we start
strict vxlan xmit tos value by RT_TOS(), which limits the tos value less
than 0x1E. With current value 0x40 the test will failed with "v1: Expected
to capture 10 packets, got 0". So let's choose a smaller tos value for
testing.
Fixes: d417ecf533 ("selftests: forwarding: vxlan_bridge_1d: Add a TOS test")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2759647247 ("ipv6: fix ECMP route replacement") it is no
longer possible to replace an ECMP-able route by a non ECMP-able route.
For example,
ip route add 2001:db8::1/128 via fe80::1 dev dummy0
ip route replace 2001:db8::1/128 dev dummy0
does not work as expected.
Tweak the replacement logic so that point 3 in the log of the above commit
becomes:
3. If the new route is not ECMP-able, and no matching non-ECMP-able route
exists, replace matching ECMP-able route (if any) or add the new route.
We can now summarize the entire replace semantics to:
When doing a replace, prefer replacing a matching route of the same
"ECMP-able-ness" as the replace argument. If there is no such candidate,
fallback to the first route found.
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
For tc ip_proto filter, when we extract the flow via __skb_flow_dissect()
without flag FLOW_DISSECTOR_F_STOP_AT_ENCAP, we will continue extract to
the inner proto.
So for GRE + ICMP messages, we should not track GRE proto, but inner ICMP
proto.
For test mirror_gre.sh, it may make user confused if we capture ICMP
message on $h3(since the flow is GRE message). So I move the capture
dev to h3-gt{4,6}, and only capture ICMP message.
Before the fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw) [ OK ]
TEST: egress mirror to gretap (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap (skip_hw) [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: egress mirror to gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL]
Expected to capture 10 packets, got 0.
TEST: two simultaneously configured mirrors (skip_hw) [ OK ]
WARN: Could not test offloaded functionality
After fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw) [ OK ]
TEST: egress mirror to gretap (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap (skip_hw) [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw) [ OK ]
TEST: egress mirror to gretap: envelope MAC (skip_hw) [ OK ]
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ]
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ]
TEST: two simultaneously configured mirrors (skip_hw) [ OK ]
WARN: Could not test offloaded functionality
Fixes: ba8d39871a ("selftests: forwarding: Add test for mirror to gretap")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <pmachata@gmail.com>
Tested-by: Petr Machata <pmachata@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KVM documentation to rst format, which was very welcome.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeRYe2AAoJEL/70l94x66DSdsH/31rMoISGbPReQNKDZtondwr
UNLYHBLau46OR5JiLaKDqRODi12CXwrB6KZyRtQg+PeU/aCaFqW09kDOtMdV4AMl
2bEl4VfUuClsGXBQL5WWsb+adaWxHBtRFPcaT0xMAE+JXxAvt2o7rstOydM4yB9f
vM9TqEP+oVGyqx0FsuCND+zu/qZqNOOqJ1eZCrzqZKwFS8lrjsYtBG4K8rfnvXnI
uGxFnbmZuJKpXpRgCebDdB98m0KEWfAs0S8aOO4NRfmymUBcjMeIeqQz0Mnt17xJ
Fz0KktwdGL28qJ+fnE51i/IBqCoBJL2BmIesSiGKVr1alpHA1ngKvUmcbtHkAXw=
=To92
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bugfixes and improvements to selftests.
On top of this, Mauro converted the KVM documentation to rst format,
which was very welcome"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (44 commits)
docs: virt: guest-halt-polling.txt convert to ReST
docs: kvm: review-checklist.txt: rename to ReST
docs: kvm: Convert timekeeping.txt to ReST format
docs: kvm: Convert s390-diag.txt to ReST format
docs: kvm: Convert ppc-pv.txt to ReST format
docs: kvm: Convert nested-vmx.txt to ReST format
docs: kvm: Convert mmu.txt to ReST format
docs: kvm: Convert locking.txt to ReST format
docs: kvm: Convert hypercalls.txt to ReST format
docs: kvm: arm/psci.txt: convert to ReST
docs: kvm: convert arm/hyp-abi.txt to ReST
docs: kvm: Convert api.txt to ReST format
docs: kvm: convert devices/xive.txt to ReST
docs: kvm: convert devices/xics.txt to ReST
docs: kvm: convert devices/vm.txt to ReST
docs: kvm: convert devices/vfio.txt to ReST
docs: kvm: convert devices/vcpu.txt to ReST
docs: kvm: convert devices/s390_flic.txt to ReST
docs: kvm: convert devices/mpic.txt to ReST
docs: kvm: convert devices/arm-vgit.txt to ReST
...
Because wireguard is calling icmp from network device context, it should
use the ndo helper so that the rate limiting applies correctly. This
commit adds a small test to the wireguard test suite to ensure that the
new functions continue doing the right thing in the context of
wireguard. It does this by setting up a condition that will definately
evoke an icmp error message from the driver, but along a nat'd path.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that newer glibcs check that openat(O_CREAT) was provided a
fourth argument (rather than passing garbage), resulting in the
following build error:
> In file included from /usr/include/fcntl.h:301,
> from helpers.c:9:
> In function 'openat',
> inlined from 'touchat' at helpers.c:49:11:
> /usr/include/x86_64-linux-gnu/bits/fcntl2.h:126:4: error: call to
> '__openat_missing_mode' declared with attribute error: openat with O_CREAT
> or O_TMPFILE in third argument needs 4 arguments
> 126 | __openat_missing_mode ();
> | ^~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
While building selftests, the following errors were observed:
> tools/testing/selftests/timens'
> gcc -Wall -Werror -pthread -lrt -ldl timens.c -o tools/testing/selftests/timens/timens
> /usr/bin/ld: /tmp/ccGy5CST.o: in function `check_config_posix_timers':
> timens.c:(.text+0x65a): undefined reference to `timer_create'
> collect2: error: ld returned 1 exit status
Quoting commit 870f193d48 ("selftests: net: use LDLIBS instead of
LDFLAGS"):
The default Makefile rule looks like:
$(CC) $(CFLAGS) $(LDFLAGS) $@ $^ $(LDLIBS)
When linking is done by gcc itself, no issue, but when it needs to be passed
to proper ld, only LDLIBS follows and then ld cannot know what libs to link
with.
More detail:
https://www.gnu.org/software/make/manual/html_node/Implicit-Variables.html
LDFLAGS
Extra flags to give to compilers when they are supposed to invoke the linker,
‘ld’, such as -L. Libraries (-lfoo) should be added to the LDLIBS variable
instead.
LDLIBS
Library flags or names given to compilers when they are supposed to invoke the
linker, ‘ld’. LOADLIBES is a deprecated (but still supported) alternative to
LDLIBS. Non-library linker flags, such as -L, should go in the LDFLAGS
variable.
While at here, correct other selftests, not only timens ones.
Reported-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Expand the cgroup test-suite to include tests for CLONE_INTO_CGROUP.
This adds the following tests:
- CLONE_INTO_CGROUP manages to clone a process directly into a correctly
delegated cgroup
- CLONE_INTO_CGROUP fails to clone a process into a cgroup that has been
removed after we've opened an fd to it
- CLONE_INTO_CGROUP fails to clone a process into an invalid domain
cgroup
- CLONE_INTO_CGROUP adheres to the no internal process constraint
- CLONE_INTO_CGROUP works with the freezer feature
Cc: Tejun Heo <tj@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: cgroups@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Acked-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add new test to verify that a cgroup with dead processes can be destroyed.
The test spawns a child process which allocates and touches 100MB of RAM
to ensure prolonged exit. Subsequently it kills the child, waits until
the cgroup containing the child is empty and destroys the cgroup.
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
[mkoutny@suse.com: Fix typo in test_cgcore_destroy comment]
Acked-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
x86_register enum is not used, let's remove it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
L2 guest calls vmcall and L1 checks the exit status does
correspond.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Tested-by: Wei Huang <wei.huang2@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the basic infrastructure needed to test AMD nested SVM.
This is largely copied from the KVM unit test infrastructure.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
get_gdt_base() and get_idt_base() only return the base address
of the descriptor tables. Soon we will need to get the size as well.
Change the prototype of those functions so that they return
the whole desc_ptr struct instead of the address field.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: Wei Huang <wei.huang2@amd.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SYN cookie test with reuseport BPF doesn't make sense for UDP sockets. We
don't run it but the test_progs test runner doesn't know about it. Mark the
test as skipped so the test_progs can report correctly how many tests were
skipped.
Fixes: 7ee0d4e97b ("selftests/bpf: Switch reuseport tests for test_progs framework")
Reported-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200212103208.438419-1-jakub@cloudflare.com
There is a typo in checking the "saved_tcp_fo" and instead
"saved_tcp_syncookie" is checked again. This patch fixes it
and also breaks them into separate if statements such that
the test will abort asap.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200211175910.3235321-1-kafai@fb.com
For now, disable MBA and MBM tests for AMD. Deciding test pass/fail
is not clear right now. We can enable when we have some clarity.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
RESCTRL feature is supported both on Intel and AMD now. Some features
are implemented differently. Add vendor detection mechanism. Use the vendor
check where there are differences.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Cache Allocation Technology (CAT) selftest allocates a portion of
last level cache and starts a benchmark to read each cache
line in this portion of cache. Measure the cache misses in perf and
the misses should be equal to the number of cache lines in this
portion of cache.
We don't use CQM to calculate cache usage because some CAT enabled
platforms don't have CQM.
Co-developed-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Cache QoS Monitoring (CQM) selftest starts stressful cache benchmark
with specified size of memory to access the cache. Last Level cache
occupancy reported by CQM should be close to the size of the memory.
Co-developed-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
MBA (Memory Bandwidth Allocation) test starts a stressful memory
bandwidth benchmark and allocates memory bandwidth from 100% down
to 10% for the benchmark process. For each allocation, compare
perf IMC counter and mbm total bytes from resctrl. The difference
between the two values should be within a threshold to pass the test.
Default benchmark is built-in fill_buf. But users can specify their
own benchmark by option "-b".
We can add memory bandwidth allocation for multiple processes in the
future.
Co-developed-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
MBM (Memory Bandwidth Monitoring) test is the first implemented selftest.
It starts a stressful memory bandwidth benchmark and assigns the
bandwidth pid in a resctrl monitoring group. Read and compare perf IMC
counter and MBM total bytes for the benchmark. The numbers should be
close enough to pass the test.
Default benchmark is built-in fill_buf. But users can specify their
own benchmark by option "-b".
We can add memory bandwidth monitoring for multiple processes in the
future.
Co-developed-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Built-in benchmark fill_buf generates stressful memory bandwidth
and cache traffic.
Later it will be used as a default benchmark by various resctrl tests
such as MBA (Memory Bandwidth Allocation) and MBM (Memory Bandwidth
Monitoring) tests.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The callback starts a child process and puts the child pid in created
resctrl group with specified memory bandwidth in schemata. The child
starts running benchmark.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Total memory bandwidth can be monitored from perf IMC counter and from
resctrl file system. Later the two will be compared to verify the total
memory bandwidth read from resctrl is correct.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Co-developed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Co-developed-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
With some shells, the command construed for install of bpf selftests becomes
too large due to long list of files:
make[1]: execvp: /bin/sh: Argument list too long
make[1]: *** [../lib.mk:73: install] Error 127
Currently, each of the file lists is replicated three times in the command:
in the shell 'if' condition, in the 'echo' and in the 'rsync'. Reduce that
by one instance by using make conditionals and separate the echo and rsync
into two shell commands. (One would be inclined to just remove the '@' at
the beginning of the rsync command and let 'make' echo it by itself;
unfortunately, it appears that the '@' in the front of mkdir silences output
also for the following commands.)
Also, separate handling of each of the lists to its own shell command.
The semantics of the makefile is unchanged before and after the patch. The
ability of individual test directories to override INSTALL_RULE is retained.
Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Tested-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit 5f70bde26a ("selftests: fix build behaviour on targets' failures")
added a logic to track failure of builds of individual targets. However, it
does exactly the opposite of what a distro kernel needs: we create a RPM
package with a selected set of selftests and we need the build to fail if
build of any of the targets fail.
Both use cases are valid. A distribution kernel is in control of what is
included in the kernel and what is being built; any error needs to be
flagged and acted upon. A CI system that tries to build as many tests as
possible on the best effort basis is not really interested in a failure here
and there.
Support both use cases by introducing a FORCE_TARGETS variable. It is
switched off by default to make life for CI systems easier, distributions
can easily switch it on while building their packages.
Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
tpm2 tests set fails if there is no /dev/tpm0 and /dev/tpmrm0
supported. Check if these files exist before run and mark test as
skipped in case of absence.
Signed-off-by: Nikita Sobolev <Nikita.Sobolev@synopsys.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
While running the ftracetests, the pid filter test failed because the
instance "foo" existed, and it was using it to rerun the test under a
instance named foo. The collision caused the test to fail as the mkdir
failed as the name already existed.
As of commit b5b77be812 ("selftests: ftrace: Allow some tests to be run
in a tracing instance") all a selftest needs to do to be tested in an
instance is to set the "instance" flag. There's no reason a selftest needs
to create an instance to run its test in an instance directly.
Remove the open coded testing in an instance for the pid filter test and
have it set the "instance" flag instead.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
There is a spelling mistake in a literal string, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
I have an experimental setup where almost every possible system
service (even early startup ones) runs in separate namespace, using a
dedicated, minimal file system. In process of minimizing the contents
of the file systems with regards to modules and firmware files, I
noticed that in my system, the firmware files are loaded from three
different mount namespaces, those of systemd-udevd, init and
systemd-networkd. The logic of the source namespace is not very clear,
it seems to depend on the driver, but the namespace of the current
process is used.
So, this patch tries to make things a bit clearer and changes the
loading of firmware files only from the mount namespace of init. This
may also improve security, though I think that using firmware files as
attack vector could be too impractical anyway.
Later, it might make sense to make the mount namespace configurable,
for example with a new file in /proc/sys/kernel/firmware_config/. That
would allow a dedicated file system only for firmware files and those
need not be present anywhere else. This configurability would make
more sense if made also for kernel modules and /sbin/modprobe. Modules
are already loaded from init namespace (usermodehelper uses kthreadd
namespace) except when directly loaded by systemd-udevd.
Instead of using the mount namespace of the current process to load
firmware files, use the mount namespace of init process.
Link: https://lore.kernel.org/lkml/bb46ebae-4746-90d9-ec5b-fce4c9328c86@gmail.com/
Link: https://lore.kernel.org/lkml/0e3f7653-c59d-9341-9db2-c88f5b988c68@gmail.com/
Signed-off-by: Topi Miettinen <toiwoton@gmail.com>
Link: https://lore.kernel.org/r/20200123125839.37168-1-toiwoton@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix following build error. We could push a tcp.h header into one of the
include paths, but I think its easy enough to simply pull in the three
defines we need here. If we end up using more of tcp.h at some point
we can pull it in later.
/home/john/git/bpf/tools/testing/selftests/bpf/prog_tests/sockmap_basic.c: In function ‘connected_socket_v4’:
/home/john/git/bpf/tools/testing/selftests/bpf/prog_tests/sockmap_basic.c:20:11: error: ‘TCP_REPAIR_ON’ undeclared (first use in this function)
repair = TCP_REPAIR_ON;
^
/home/john/git/bpf/tools/testing/selftests/bpf/prog_tests/sockmap_basic.c:20:11: note: each undeclared identifier is reported only once for each function it appears in
/home/john/git/bpf/tools/testing/selftests/bpf/prog_tests/sockmap_basic.c:29:11: error: ‘TCP_REPAIR_OFF_NO_WP’ undeclared (first use in this function)
repair = TCP_REPAIR_OFF_NO_WP;
Then with fix,
$ ./test_progs -n 44
#44/1 sockmap create_update_free:OK
#44/2 sockhash create_update_free:OK
#44 sockmap_basic:OK
Fixes: 5d3919a953 ("selftests/bpf: Test freeing sockmap/sockhash with a socket in it")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/158131347731.21414.12120493483848386652.stgit@john-Precision-5820-Tower
Pull networking fixes from David Miller:
1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.
2) Fix thermal zone registration in iwlwifi, from Andrei
Otcheretianski.
3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.
4) Use after free in mptcp, from Florian Westphal.
5) Use after free in wireguard's root_remove_peer_lists, from Eric
Dumazet.
6) Properly access packets heads in bonding alb code, from Eric
Dumazet.
7) Fix data race in skb_queue_len(), from Qian Cai.
8) Fix regression in r8169 on some chips, from Heiner Kallweit.
9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.
10) Certain kinds of set link netlink operations can cause a NULL deref
in the ipv6 addrconf code. Fix from Eric Dumazet.
11) Don't cancel uninitialized work queue in drop monitor, from Ido
Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: thunderx: use proper interface type for RGMII
mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
bpf: Improve bucket_log calculation logic
selftests/bpf: Test freeing sockmap/sockhash with a socket in it
bpf, sockhash: Synchronize_rcu before free'ing map
bpf, sockmap: Don't sleep while holding RCU lock on tear-down
bpftool: Don't crash on missing xlated program instructions
bpf, sockmap: Check update requirements after locking
drop_monitor: Do not cancel uninitialized work item
mlxsw: spectrum_dpipe: Add missing error path
mlxsw: core: Add validation of hardware device types for MGPIR register
mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
selftests: mlxsw: Add test cases for local table route replacement
mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
net: dsa: microchip: enable module autoprobe
ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
dpaa_eth: support all modes with rate adapting PHYs
net: stmmac: update pci platform data to use phy_interface
net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
...
Daniel Borkmann says:
====================
pull-request: bpf 2020-02-07
The following pull-request contains BPF updates for your *net* tree.
We've added 15 non-merge commits during the last 10 day(s) which contain
a total of 12 files changed, 114 insertions(+), 31 deletions(-).
The main changes are:
1) Various BPF sockmap fixes related to RCU handling in the map's tear-
down code, from Jakub Sitnicki.
2) Fix macro state explosion in BPF sk_storage map when calculating its
bucket_log on allocation, from Martin KaFai Lau.
3) Fix potential BPF sockmap update race by rechecking socket's established
state under lock, from Lorenz Bauer.
4) Fix crash in bpftool on missing xlated instructions when kptr_restrict
sysctl is set, from Toke Høiland-Jørgensen.
5) Fix i40e's XSK wakeup code to return proper error in busy state and
various misc fixes in xdpsock BPF sample code, from Maciej Fijalkowski.
6) Fix the way modifiers are skipped in BTF in the verifier while walking
pointers to avoid program rejection, from Alexei Starovoitov.
7) Fix Makefile for runqslower BPF tool to i) rebuild on libbpf changes and
ii) to fix undefined reference linker errors for older gcc version due to
order of passed gcc parameters, from Yulia Kartseva and Song Liu.
8) Fix a trampoline_count BPF kselftest warning about missing braces around
initializer, from Andrii Nakryiko.
9) Fix up redundant "HAVE" prefix from large INSN limit kernel probe in
bpftool, from Michal Rostecki.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7e81a35302 ("bpf: Sockmap, ensure sock lock held during tear
down") introduced sleeping issues inside RCU critical sections and while
holding a spinlock on sockmap/sockhash tear-down. There has to be at least
one socket in the map for the problem to surface.
This adds a test that triggers the warnings for broken locking rules. Not a
fix per se, but rather tooling to verify the accompanying fixes. Run on a
VM with 1 vCPU to reproduce the warnings.
Fixes: 7e81a35302 ("bpf: Sockmap, ensure sock lock held during tear down")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200206111652.694507-4-jakub@cloudflare.com
Test that routes in the main table do not replace identical routes in
the local table and that routes in the local table do replace identical
routes in the main table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix register corruption
* ENOTSUPP/EOPNOTSUPP mixed
* reset cleanups/fixes
* selftests
x86:
* Bug fixes and cleanups
* AMD support for APIC virtualization even in combination with
in-kernel PIT or IOAPIC.
MIPS:
* Compilation fix.
Generic:
* Fix refcount overflow for zero page.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeOuf7AAoJEL/70l94x66DOBQH/j1W9lUpbDgr9aWbrZT+O/yP
FWzUDrRlCZCjV1FQKbGPa4YLeDRTG5n+RIQTjmCGRqiMqeoELSJ1+iK99e97nG/u
L28zf/90Nf0R+wwHL4AOFeploTYfG4WP8EVnlr3CG2UCJrNjxN1KU7yRZoWmWa2d
ckLJ8ouwNvx6VZd233LVmT38EP4352d1LyqIL8/+oXDIyAcRJLFQu1gRCwagsh3w
1v1czowFpWnRQ/z9zU7YD+PA4v85/Ge8sVVHlpi1X5NgV/khk4U6B0crAw6M+la+
mTmpz9g56oAh9m9NUdtv4zDCz1EWGH0v8+ZkAajUKtrM0ftJMn57P6p8PH4VVlE=
=5+Wl
-----END PGP SIGNATURE-----
Merge tag 'kvm-5.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"s390:
- fix register corruption
- ENOTSUPP/EOPNOTSUPP mixed
- reset cleanups/fixes
- selftests
x86:
- Bug fixes and cleanups
- AMD support for APIC virtualization even in combination with
in-kernel PIT or IOAPIC.
MIPS:
- Compilation fix.
Generic:
- Fix refcount overflow for zero page"
* tag 'kvm-5.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (42 commits)
KVM: vmx: delete meaningless vmx_decache_cr0_guest_bits() declaration
KVM: x86: Mark CR4.UMIP as reserved based on associated CPUID bit
x86: vmxfeatures: rename features for consistency with KVM and manual
KVM: SVM: relax conditions for allowing MSR_IA32_SPEC_CTRL accesses
KVM: x86: Fix perfctr WRMSR for running counters
x86/kvm/hyper-v: don't allow to turn on unsupported VMX controls for nested guests
x86/kvm/hyper-v: move VMX controls sanitization out of nested_enable_evmcs()
kvm: mmu: Separate generating and setting mmio ptes
kvm: mmu: Replace unsigned with unsigned int for PTE access
KVM: nVMX: Remove stale comment from nested_vmx_load_cr3()
KVM: MIPS: Fold comparecount_func() into comparecount_wakeup()
KVM: MIPS: Fix a build error due to referencing not-yet-defined function
x86/kvm: do not setup pv tlb flush when not paravirtualized
KVM: fix overflow of zero page refcount with ksm running
KVM: x86: Take a u64 when checking for a valid dr7 value
KVM: x86: use raw clock values consistently
KVM: x86: reorganize pvclock_gtod_data members
KVM: nVMX: delete meaningless nested_vmx_run() declaration
KVM: SVM: allow AVIC without split irqchip
kvm: ioapic: Lazy update IOAPIC EOI
...
Turns out that when we accept a new subflow, the newly created
inet_sk(tcp_sk)->pinet6 points at the ipv6_pinfo structure of the
listener socket.
This wasn't caught by the selftest because it closes the accepted fd
before the listening one.
adding a close(listenfd) after accept returns is enough:
BUG: KASAN: use-after-free in inet6_getname+0x6ba/0x790
Read of size 1 at addr ffff88810e310866 by task mptcp_connect/2518
Call Trace:
inet6_getname+0x6ba/0x790
__sys_getpeername+0x10b/0x250
__x64_sys_getpeername+0x6f/0xb0
also alter test program to exercise this.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added new "bootconfig".
Looks for a file appended to initrd to add boot config options.
This has been discussed thoroughly at Linux Plumbers.
Very useful for adding kprobes at bootup.
Only enabled if "bootconfig" is on the real kernel command line.
- Created dynamic event creation.
Merges common code between creating synthetic events and
kprobe events.
- Rename perf "ring_buffer" structure to "perf_buffer"
- Rename ftrace "ring_buffer" structure to "trace_buffer"
Had to rename existing "trace_buffer" to "array_buffer"
- Allow trace_printk() to work withing (some) tracing code.
- Sort of tracing configs to be a little better organized
- Fixed bug where ftrace_graph hash was not being protected properly
- Various other small fixes and clean ups
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXjtAURQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qshOAQDzopQmvAVrrI6oogghr8JQA30Z2yqT
i+Ld7vPWL2MV9wEA1S+zLGDSYrj8f/vsCq6BxRYT1ApO+YtmY6LTXiUejwg=
=WNds
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Added new "bootconfig".
This looks for a file appended to initrd to add boot config options,
and has been discussed thoroughly at Linux Plumbers.
Very useful for adding kprobes at bootup.
Only enabled if "bootconfig" is on the real kernel command line.
- Created dynamic event creation.
Merges common code between creating synthetic events and kprobe
events.
- Rename perf "ring_buffer" structure to "perf_buffer"
- Rename ftrace "ring_buffer" structure to "trace_buffer"
Had to rename existing "trace_buffer" to "array_buffer"
- Allow trace_printk() to work withing (some) tracing code.
- Sort of tracing configs to be a little better organized
- Fixed bug where ftrace_graph hash was not being protected properly
- Various other small fixes and clean ups
* tag 'trace-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (88 commits)
bootconfig: Show the number of nodes on boot message
tools/bootconfig: Show the number of bootconfig nodes
bootconfig: Add more parse error messages
bootconfig: Use bootconfig instead of boot config
ftrace: Protect ftrace_graph_hash with ftrace_sync
ftrace: Add comment to why rcu_dereference_sched() is open coded
tracing: Annotate ftrace_graph_notrace_hash pointer with __rcu
tracing: Annotate ftrace_graph_hash pointer with __rcu
bootconfig: Only load bootconfig if "bootconfig" is on the kernel cmdline
tracing: Use seq_buf for building dynevent_cmd string
tracing: Remove useless code in dynevent_arg_pair_add()
tracing: Remove check_arg() callbacks from dynevent args
tracing: Consolidate some synth_event_trace code
tracing: Fix now invalid var_ref_vals assumption in trace action
tracing: Change trace_boot to use synth_event interface
tracing: Move tracing selftests to bottom of menu
tracing: Move mmio tracer config up with the other tracers
tracing: Move tracing test module configs together
tracing: Move all function tracing configs together
tracing: Documentation for in-kernel synthetic event API
...
Without this, we wind up proceeding too early sometimes when the
previous process has just used the same listening port. So, we tie the
listening socket query to the specific pid we're interested in.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_ENABLE_WARN_DEPRECATED is gone since commit 771c035372
("deprecate the '__deprecated' attribute warnings entirely and for
good").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that peers with low order points are ignored, both in the case
where we already have a device private key and in the case where we do
not. This adds points that naturally give a zero output.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Use after free in rxrpc_put_local(), from David Howells.
2) Fix 64-bit division error in mlxsw, from Nathan Chancellor.
3) Make sure we clear various bits of TCP state in response to
tcp_disconnect(). From Eric Dumazet.
4) Fix netlink attribute policy in cls_rsvp, from Eric Dumazet.
5) txtimer must be deleted in stmmac suspend(), from Nicolin Chen.
6) Fix TC queue mapping in bnxt_en driver, from Michael Chan.
7) Various netdevsim fixes from Taehee Yoo (use of uninitialized data,
snapshot panics, stack out of bounds, etc.)
8) cls_tcindex changes hash table size after allocating the table, fix
from Cong Wang.
9) Fix regression in the enforcement of session ID uniqueness in l2tp.
We only have to enforce uniqueness for IP based tunnels not UDP
ones. From Ridge Kennedy.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
gtp: use __GFP_NOWARN to avoid memalloc warning
l2tp: Allow duplicate session creation with UDP
r8152: Add MAC passthrough support to new device
net_sched: fix an OOB access in cls_tcindex
qed: Remove set but not used variable 'p_link'
tc-testing: add missing 'nsPlugin' to basic.json
tc-testing: fix eBPF tests failure on linux fresh clones
net: hsr: fix possible NULL deref in hsr_handle_frame()
netdevsim: remove unused sdev code
netdevsim: use __GFP_NOWARN to avoid memalloc warning
netdevsim: use IS_ERR instead of IS_ERR_OR_NULL for debugfs
netdevsim: fix stack-out-of-bounds in nsim_dev_debugfs_init()
netdevsim: fix panic in nsim_dev_take_snapshot_write()
netdevsim: disable devlink reload when resources are being used
netdevsim: fix using uninitialized resources
bnxt_en: Fix TC queue mapping.
bnxt_en: Fix logic that disables Bus Master during firmware reset.
bnxt_en: Fix RDMA driver failure with SRIOV after firmware reset.
bnxt_en: Refactor logic to re-enable SRIOV after firmware reset detected.
net: stmmac: Delete txtimer in suspend()
...
- Implement user_access_begin() and friends for our platforms that support
controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure" virtual
machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit VDSO, and
some other improvements.
- A series to use the PCI hotplug framework to control opencapi card's so that
they can be reset and re-read after flashing a new FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to:
Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen Zhou, Christophe Leroy,
Frederic Barrat, Greg Kurz, Jason A. Donenfeld, Joel Stanley, Jordan Niethe,
Julia Lawall, Krzysztof Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus
Walleij, Michael Bringmann, Nathan Chancellor, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy
Dunlap, Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago Jung
Bauermann, Tyrel Datwyler, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAl44uJgTHG1wZUBlbGxl
cm1hbi5pZC5hdQAKCRBR6+o8yOGlgGIcD/9U3R2BK3trEPOStcUbYPte9sMqkyYq
bcq4o2qrVc5deMvPhcHOQ4j28RUZOKoRODvSbXzGEGKIDlesmKjuP7AicE5qUjjV
jRtsSOlRElXmPojAgrrlWrFDJOKbW5mFSj2TY/0sjVa06Wcu1Oi6WiQs/TazvZV/
yzKh5lBL6xyQrmgH0h1VWWbblMbsA1bAL/D7m9Pgimpz0W6fOSRWgXILDUXPLBAy
Rtt7p1218xPfhe66EgbLhWLIBJb70r+Z9yJNuVbp9NMJbDAhpfOuyMNXpRCELzXD
5hwm0mFLOwxfSyBgIyIGokLRGFO6XL0uiZIG1Kp+tMxjgnNCmLlRs2R3EF1hoIWi
49DHRAdK+IEggi6S4dXG5aglz6Rsun8pb/lN7uW+M68t3wp2IYQ+H8MQh4cxPTLu
wX6KZr28lNG25yyp97nJq2Vld0xTxSSty92P8f588rkolyxzggUy0Xfen41szNrW
9/bu8NWgt7qVtHmeUoCdWqiIiuMT1k3Of7AN4uAuS6aJHx2Fxr+03ZU5yNr8WIkm
IOf27z8sUx3F8JL9cIuwAIPB0lSDPw1owvfiTYQ1VkzJa4Ko+kgv5wQ5Ors6V+ve
XspE4osSP9T9PoHK2MVlu8mOjLpoo3Ibr849J0lGHQZDP6U3kHNILGfcXA8WP/9b
Fgfh5Wj22cQe8A==
=xpG+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A pretty small batch for us, and apologies for it being a bit late, I
wanted to sneak Christophe's user_access_begin() series in.
Summary:
- Implement user_access_begin() and friends for our platforms that
support controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure"
virtual machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit
VDSO, and some other improvements.
- A series to use the PCI hotplug framework to control opencapi
card's so that they can be reset and re-read after flashing a new
FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to: Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy,
Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen
Zhou, Christophe Leroy, Frederic Barrat, Greg Kurz, Jason A.
Donenfeld, Joel Stanley, Jordan Niethe, Julia Lawall, Krzysztof
Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus Walleij, Michael
Bringmann, Nathan Chancellor, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy Dunlap,
Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain"
* tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (131 commits)
powerpc: configs: Cleanup old Kconfig options
powerpc/configs/skiroot: Enable some more hardening options
powerpc/configs/skiroot: Disable xmon default & enable reboot on panic
powerpc/configs/skiroot: Enable security features
powerpc/configs/skiroot: Update for symbol movement only
powerpc/configs/skiroot: Drop default n CONFIG_CRYPTO_ECHAINIV
powerpc/configs/skiroot: Drop HID_LOGITECH
powerpc/configs: Drop NET_VENDOR_HP which moved to staging
powerpc/configs: NET_CADENCE became NET_VENDOR_CADENCE
powerpc/configs: Drop CONFIG_QLGE which moved to staging
powerpc: Do not consider weak unresolved symbol relocations as bad
powerpc/32s: Fix kasan_early_hash_table() for CONFIG_VMAP_STACK
powerpc: indent to improve Kconfig readability
powerpc: Provide initial documentation for PAPR hcalls
powerpc: Implement user_access_save() and user_access_restore()
powerpc: Implement user_access_begin and friends
powerpc/32s: Prepare prevent_user_access() for user_access_end()
powerpc/32s: Drop NULL addr verification
powerpc/kuap: Fix set direction in allow/prevent_user_access()
powerpc/32s: Fix bad_kuap_fault()
...
since tdc tests for cls_basic need $DEV1, use 'nsPlugin' so that the
following command can be run without errors:
[root@f31 tc-testing]# ./tdc.py -c basic
Fixes: 4717b05328 ("tc-testing: Introduced tdc tests for basic filter")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when the following command is done on a fresh clone of the kernel tree,
[root@f31 tc-testing]# ./tdc.py -c bpf
test cases that need to build the eBPF sample program fail systematically,
because 'buildebpfPlugin' is unable to install the kernel headers (i.e, the
'khdr' target fails). Pass the correct environment to 'make', in place of
ENVIR, to allow running these tests.
Fixes: 4c2d39bd40 ("tc-testing: use a plugin to build eBPF program")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a test for FIN_ACK process races related reconnection
latency spike issues. The issue has described and solved by the
previous commit ("tcp: Reduce SYN resend delay if a suspicous ACK is
received").
The test program is configured with a server and a client process. The
server creates and binds a socket to a port that dynamically allocated,
listen on it, and start a infinite loop. Inside the loop, it accepts
connection, reads 4 bytes from the socket, and closes the connection.
The client is constructed as an infinite loop. Inside the loop, it
creates a socket with LINGER and NODELAY option, connect to the server,
send 4 bytes data, try read some data from server. After the read()
returns, it measure the latency from the beginning of this loop to this
point and if the latency is larger than 1 second (spike), print a
message.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull updates from Andrew Morton:
"Most of -mm and quite a number of other subsystems: hotfixes, scripts,
ocfs2, misc, lib, binfmt, init, reiserfs, exec, dma-mapping, kcov.
MM is fairly quiet this time. Holidays, I assume"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
kcov: ignore fault-inject and stacktrace
include/linux/io-mapping.h-mapping: use PHYS_PFN() macro in io_mapping_map_atomic_wc()
execve: warn if process starts with executable stack
reiserfs: prevent NULL pointer dereference in reiserfs_insert_item()
init/main.c: fix misleading "This architecture does not have kernel memory protection" message
init/main.c: fix quoted value handling in unknown_bootoption
init/main.c: remove unnecessary repair_env_string in do_initcall_level
init/main.c: log arguments and environment passed to init
fs/binfmt_elf.c: coredump: allow process with empty address space to coredump
fs/binfmt_elf.c: coredump: delete duplicated overflow check
fs/binfmt_elf.c: coredump: allocate core ELF header on stack
fs/binfmt_elf.c: make BAD_ADDR() unlikely
fs/binfmt_elf.c: better codegen around current->mm
fs/binfmt_elf.c: don't copy ELF header around
fs/binfmt_elf.c: fix ->start_code calculation
fs/binfmt_elf.c: smaller code generation around auxv vector fill
lib/find_bit.c: uninline helper _find_next_bit()
lib/find_bit.c: join _find_next_bit{_le}
uapi: rename ext2_swab() to swab() and share globally in swab.h
lib/scatterlist.c: adjust indentation in __sg_alloc_table
...
Fix the gup benchmark flags to use the symbolic FOLL_WRITE, instead of a
hard-coded "1" value.
Also, clean up the filtering of gup flags a little, by just doing it
once before issuing any of the get_user_pages*() calls. This makes it
harder to overlook, instead of having little "gup_flags & 1" phrases in
the function calls.
Link: http://lkml.kernel.org/r/20200107224558.2362728-22-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Jan Kara <jack@suse.cz>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PPC: Bugfixes
x86:
* Support for mapping DAX areas with large nested page table entries.
* Cleanups and bugfixes here too. A particularly important one is
a fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to exploit
the guest kernel, for which the embargo expired today.
* Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
* Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling hyperthread
to read it), which unfortunately is an even bigger whack-a-mole game
than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large refactoring
of vCPU creation that affects all architectures but should not have any
visible effect.
s390 will come next week together with some more x86 patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeMxtCAAoJEL/70l94x66DQxIIAJv9hMmXLQHGFnUMskjGErR6
DCLSC0YRdRMwE50CerblyJtGsMwGsPyHZwvZxoAceKJ9w0Yay9cyaoJ87ItBgHoY
ce0HrqIUYqRSJ/F8WH2lSzkzMBr839rcmqw8p1tt4D5DIsYnxHGWwRaaP+5M/1KQ
YKFu3Hea4L00U339iIuDkuA+xgz92LIbsn38svv5fxHhPAyWza0rDEYHNgzMKuoF
IakLf5+RrBFAh6ZuhYWQQ44uxjb+uQa9pVmcqYzzTd5t1g4PV5uXtlJKesHoAvik
Eba8IEUJn+HgQJjhp3YxQYuLeWOwRF3bwOiZ578MlJ4OPfYXMtbdlqCQANHOcGk=
=H/q1
-----END PGP SIGNATURE-----
Merge tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"This is the first batch of KVM changes.
ARM:
- cleanups and corner case fixes.
PPC:
- Bugfixes
x86:
- Support for mapping DAX areas with large nested page table entries.
- Cleanups and bugfixes here too. A particularly important one is a
fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to
exploit the guest kernel, for which the embargo expired today.
- Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
- Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling
hyperthread to read it), which unfortunately is an even bigger
whack-a-mole game than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large
refactoring of vCPU creation that affects all architectures but should
not have any visible effect.
s390 will come next week together with some more x86 patches"
* tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
x86/KVM: Clean up host's steal time structure
x86/KVM: Make sure KVM_VCPU_FLUSH_TLB flag is not missed
x86/kvm: Cache gfn to pfn translation
x86/kvm: Introduce kvm_(un)map_gfn()
x86/kvm: Be careful not to clear KVM_VCPU_FLUSH_TLB bit
KVM: PPC: Book3S PR: Fix -Werror=return-type build failure
KVM: PPC: Book3S HV: Release lock on page-out failure path
KVM: arm64: Treat emulated TVAL TimerValue as a signed 32-bit integer
KVM: arm64: pmu: Only handle supported event counters
KVM: arm64: pmu: Fix chained SW_INCR counters
KVM: arm64: pmu: Don't mark a counter as chained if the odd one is disabled
KVM: arm64: pmu: Don't increment SW_INCR if PMCR.E is unset
KVM: x86: Use a typedef for fastop functions
KVM: X86: Add 'else' to unify fastop and execute call path
KVM: x86: inline memslot_valid_for_gpte
KVM: x86/mmu: Use huge pages for DAX-backed files
KVM: x86/mmu: Remove lpage_is_disallowed() check from set_spte()
KVM: x86/mmu: Fold max_mapping_level() into kvm_mmu_hugepage_adjust()
KVM: x86/mmu: Zap any compound page when collapsing sptes
KVM: x86/mmu: Remove obsolete gfn restoration in FNAME(fetch)
...
Local IRQs are reset by a normal cpu reset. The initial cpu reset and
the clear cpu reset, as superset of the normal reset, both clear the
IRQs too.
Let's inject an interrupt to a vCPU before calling a reset and see if
it is gone after the reset.
We choose to inject only an emergency interrupt at this point and can
extend the test to other types of IRQs later.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
[minor fixups]
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Link: https://lore.kernel.org/r/20200131100205.74720-7-frankja@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Test if the registers end up having the correct values after a normal,
initial and clear reset.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Link: https://lore.kernel.org/r/20200131100205.74720-6-frankja@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add library access to more registers.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Link: https://lore.kernel.org/r/20200131100205.74720-5-frankja@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
uapi:
- dma-buf heaps added (and fixed)
- command line add support for panel oreientation
- command line allow overriding penguin count
drm:
- mipi dsi definition updates
- lockdep annotations for dma_resv
- remove dma-buf kmap/kunmap support
- constify fb_ops in all fbdev drivers
- MST fix for daisy chained hotplug-
- CTA-861-G modes with VIC >= 193 added
- fix drm_panel_of_backlight export
- LVDS decoder support
- more device based logging support
- scanline alighment for dumb buffers
- MST DSC helpers
scheduler:
- documentation fixes
- job distribution improvements
panel:
- Logic PD type 28 panel support
- Jimax8729d MIPI-DSI
- igenic JZ4770
- generic DSI devicetree bindings
- sony acx424AKP panel
- Leadtek LTK500HD1829
- xinpeng XPP055C272
- AUO B116XAK01
- GiantPlus GPM940B0
- BOE NV140FHM-N49
- Satoz SAT050AT40H12R2
- Sharp LS020B1DD01D panels.
ttm:
- use blocking WW lock
i915:
- hw/uapi state separation
- Lock annotation improvements
- selftest improvements
- ICL/TGL DSI VDSC support
- VBT parsing improvments
- Display refactoring
- DSI updates + fixes
- HDCP 2.2 for CFL
- CML PCI ID fixes
- GLK+ fbc fix
- PSR fixes
- GEN/GT refactor improvments
- DP MST fixes
- switch context id alloc to xarray
- workaround updates
- LMEM debugfs support
- tiled monitor fixes
- ICL+ clock gating programming removed
- DP MST disable sequence fixed
- LMEM discontiguous object maps
- prefaulting for discontiguous objects
- use LMEM for dumb buffers if possible
- add LMEM mmap support
amdgpu:
- enable sync object timelines for vulkan
- MST atomic routines
- enable MST DSC support
- add DMCUB display microengine support
- DC OEM i2c support
- Renoir DC fixes
- Initial HDCP 2.x support
- BACO support for Arcturus
- Use BACO for runtime PM power save
- gfxoff on navi10
- gfx10 golden updates and fixes
- DCN support on POWER
- GFXOFF for raven1 refresh
- MM engine idle handlers cleanup
- 10bpc EDP panel fixes
- renoir watermark fixes
- SR-IOV fixes
- Arcturus VCN fixes
- GDDR6 training fixes
- freesync fixes
- Pollock support
amdkfd:
- unify more codepath with amdgpu
- use KIQ to setup HIQ rather than MMIO
radeon:
- fix vma fault handler race
- PPC DMA fix
- register check fixes for r100/r200
nouveau:
- mmap_sem vs dma_resv fix
- rewrite the ACR secure boot code for Turing
- TU10x graphics engine support (TU11x pending)
- Page kind mapping for turing
- 10-bit LUT support
- GP10B Tegra fixes
- HD audio regression fix
hisilicon/hibmc:
- use generic fbdev code and helpers
rockchip:
- dsi/px30 support
virtio:
- fb damage support
- static some functions
vc4:
- use dma_resv lock wrappers
msm:
- use dma_resv lock wrappers
- sc7180 display + DSI support
- a618 support
- UBWC support improvements
vmwgfx:
- updates + new logging uapi
exynos:
- enable/disable callback cleanups
etnaviv:
- use dma_resv lock wrappers
atmel-hlcdc:
- clock fixes
mediatek:
- cmdq support
- non-smooth cursor fixes
- ctm property support
sun4i:
- suspend support
- A64 mipi dsi support
rcar-du:
- Color management module support
- LVDS encoder dual-link support
- R8A77980 support
analogic:
- add support for an6345
ast:
- atomic modeset support
- primary plane garbage fix
arcgpu:
- fixes for fourcc handling
tegra:
- minor fixes and improvments
mcde:
- vblank support
meson:
- OSD1 plane AFBC commit
gma500:
- add pageflip support
- reomve global drm_dev
komeda:
- tweak debugfs output
- d32 support
- runtime PM suppotr
udl:
- use generic shmem helpers
- cleanup and fixes
-----BEGIN PGP SIGNATURE-----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=oFrI
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Davbe Airlie:
"This is the main pull request for graphics for 5.6. Usual selection of
changes all over.
I've got one outstanding vmwgfx pull that touches mm so kept it
separate until after all of this lands. I'll try and get it to you
soon after this, but it might be early next week (nothing wrong with
code, just my schedule is messy)
This also hits a lot of fbdev drivers with some cleanups.
Other notables:
- vulkan timeline semaphore support added to syncobjs
- nouveau turing secureboot/graphics support
- Displayport MST display stream compression support
Detailed summary:
uapi:
- dma-buf heaps added (and fixed)
- command line add support for panel oreientation
- command line allow overriding penguin count
drm:
- mipi dsi definition updates
- lockdep annotations for dma_resv
- remove dma-buf kmap/kunmap support
- constify fb_ops in all fbdev drivers
- MST fix for daisy chained hotplug-
- CTA-861-G modes with VIC >= 193 added
- fix drm_panel_of_backlight export
- LVDS decoder support
- more device based logging support
- scanline alighment for dumb buffers
- MST DSC helpers
scheduler:
- documentation fixes
- job distribution improvements
panel:
- Logic PD type 28 panel support
- Jimax8729d MIPI-DSI
- igenic JZ4770
- generic DSI devicetree bindings
- sony acx424AKP panel
- Leadtek LTK500HD1829
- xinpeng XPP055C272
- AUO B116XAK01
- GiantPlus GPM940B0
- BOE NV140FHM-N49
- Satoz SAT050AT40H12R2
- Sharp LS020B1DD01D panels.
ttm:
- use blocking WW lock
i915:
- hw/uapi state separation
- Lock annotation improvements
- selftest improvements
- ICL/TGL DSI VDSC support
- VBT parsing improvments
- Display refactoring
- DSI updates + fixes
- HDCP 2.2 for CFL
- CML PCI ID fixes
- GLK+ fbc fix
- PSR fixes
- GEN/GT refactor improvments
- DP MST fixes
- switch context id alloc to xarray
- workaround updates
- LMEM debugfs support
- tiled monitor fixes
- ICL+ clock gating programming removed
- DP MST disable sequence fixed
- LMEM discontiguous object maps
- prefaulting for discontiguous objects
- use LMEM for dumb buffers if possible
- add LMEM mmap support
amdgpu:
- enable sync object timelines for vulkan
- MST atomic routines
- enable MST DSC support
- add DMCUB display microengine support
- DC OEM i2c support
- Renoir DC fixes
- Initial HDCP 2.x support
- BACO support for Arcturus
- Use BACO for runtime PM power save
- gfxoff on navi10
- gfx10 golden updates and fixes
- DCN support on POWER
- GFXOFF for raven1 refresh
- MM engine idle handlers cleanup
- 10bpc EDP panel fixes
- renoir watermark fixes
- SR-IOV fixes
- Arcturus VCN fixes
- GDDR6 training fixes
- freesync fixes
- Pollock support
amdkfd:
- unify more codepath with amdgpu
- use KIQ to setup HIQ rather than MMIO
radeon:
- fix vma fault handler race
- PPC DMA fix
- register check fixes for r100/r200
nouveau:
- mmap_sem vs dma_resv fix
- rewrite the ACR secure boot code for Turing
- TU10x graphics engine support (TU11x pending)
- Page kind mapping for turing
- 10-bit LUT support
- GP10B Tegra fixes
- HD audio regression fix
hisilicon/hibmc:
- use generic fbdev code and helpers
rockchip:
- dsi/px30 support
virtio:
- fb damage support
- static some functions
vc4:
- use dma_resv lock wrappers
msm:
- use dma_resv lock wrappers
- sc7180 display + DSI support
- a618 support
- UBWC support improvements
vmwgfx:
- updates + new logging uapi
exynos:
- enable/disable callback cleanups
etnaviv:
- use dma_resv lock wrappers
atmel-hlcdc:
- clock fixes
mediatek:
- cmdq support
- non-smooth cursor fixes
- ctm property support
sun4i:
- suspend support
- A64 mipi dsi support
rcar-du:
- Color management module support
- LVDS encoder dual-link support
- R8A77980 support
analogic:
- add support for an6345
ast:
- atomic modeset support
- primary plane garbage fix
arcgpu:
- fixes for fourcc handling
tegra:
- minor fixes and improvments
mcde:
- vblank support
meson:
- OSD1 plane AFBC commit
gma500:
- add pageflip support
- reomve global drm_dev
komeda:
- tweak debugfs output
- d32 support
- runtime PM suppotr
udl:
- use generic shmem helpers
- cleanup and fixes"
* tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm: (1998 commits)
drm/nouveau/fb/gp102-: allow module to load even when scrubber binary is missing
drm/nouveau/acr: return error when registering LSF if ACR not supported
drm/nouveau/disp/gv100-: not all channel types support reporting error codes
drm/nouveau/disp/nv50-: prevent oops when no channel method map provided
drm/nouveau: support synchronous pushbuf submission
drm/nouveau: signal pending fences when channel has been killed
drm/nouveau: reject attempts to submit to dead channels
drm/nouveau: zero vma pointer even if we only unreference it rather than free
drm/nouveau: Add HD-audio component notifier support
drm/nouveau: fix build error without CONFIG_IOMMU_API
drm/nouveau/kms/nv04: remove set but not used variable 'width'
drm/nouveau/kms/nv50: remove set but not unused variable 'nv_connector'
drm/nouveau/mmu: fix comptag memory leak
drm/nouveau/gr/gp10b: Use gp100_grctx and gp100_gr_zbc
drm/nouveau/pmu/gm20b,gp10b: Fix Falcon bootstrapping
drm/exynos: Rename Exynos to lowercase
drm/exynos: change callback names
drm/mst: Don't do atomic checks over disabled managers
drm/amdgpu: add the lost mutex_init back
drm/amd/display: skip opp blank or unblank if test pattern enabled
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXjFo8wAKCRCRxhvAZXjc
omaGAQDVwCHQekqxp2eC8EJH4Pkt+Bn1BLrA25stlTo93YBPHgEAsPVUCRNcrZAl
VncYmxCfpt3Yu0S/MTVXu5xrRiIXPQk=
=uqTN
-----END PGP SIGNATURE-----
Merge tag 'threads-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull thread management updates from Christian Brauner:
"Sargun Dhillon over the last cycle has worked on the pidfd_getfd()
syscall.
This syscall allows for the retrieval of file descriptors of a process
based on its pidfd. A task needs to have ptrace_may_access()
permissions with PTRACE_MODE_ATTACH_REALCREDS (suggested by Oleg and
Andy) on the target.
One of the main use-cases is in combination with seccomp's user
notification feature. As a reminder, seccomp's user notification
feature was made available in v5.0. It allows a task to retrieve a
file descriptor for its seccomp filter. The file descriptor is usually
handed of to a more privileged supervising process. The supervisor can
then listen for syscall events caught by the seccomp filter of the
supervisee and perform actions in lieu of the supervisee, usually
emulating syscalls. pidfd_getfd() is needed to expand its uses.
There are currently two major users that wait on pidfd_getfd() and one
future user:
- Netflix, Sargun said, is working on a service mesh where users
should be able to connect to a dns-based VIP. When a user connects
to e.g. 1.2.3.4:80 that runs e.g. service "foo" they will be
redirected to an envoy process. This service mesh uses seccomp user
notifications and pidfd to intercept all connect calls and instead
of connecting them to 1.2.3.4:80 connects them to e.g.
127.0.0.1:8080.
- LXD uses the seccomp notifier heavily to intercept and emulate
mknod() and mount() syscalls for unprivileged containers/processes.
With pidfd_getfd() more uses-cases e.g. bridging socket connections
will be possible.
- The patchset has also seen some interest from the browser corner.
Right now, Firefox is using a SECCOMP_RET_TRAP sandbox managed by a
broker process. In the future glibc will start blocking all signals
during dlopen() rendering this type of sandbox impossible. Hence,
in the future Firefox will switch to a seccomp-user-nofication
based sandbox which also makes use of file descriptor retrieval.
The thread for this can be found at
https://sourceware.org/ml/libc-alpha/2019-12/msg00079.html
With pidfd_getfd() it is e.g. possible to bridge socket connections
for the supervisee (binding to a privileged port) and taking actions
on file descriptors on behalf of the supervisee in general.
Sargun's first version was using an ioctl on pidfds but various people
pushed for it to be a proper syscall which he duely implemented as
well over various review cycles. Selftests are of course included.
I've also added instructions how to deal with merge conflicts below.
There's also a small fix coming from the kernel mentee project to
correctly annotate struct sighand_struct with __rcu to fix various
sparse warnings. We've received a few more such fixes and even though
they are mostly trivial I've decided to postpone them until after -rc1
since they came in rather late and I don't want to risk introducing
build warnings.
Finally, there's a new prctl() command PR_{G,S}ET_IO_FLUSHER which is
needed to avoid allocation recursions triggerable by storage drivers
that have userspace parts that run in the IO path (e.g. dm-multipath,
iscsi, etc). These allocation recursions deadlock the device.
The new prctl() allows such privileged userspace components to avoid
allocation recursions by setting the PF_MEMALLOC_NOIO and
PF_LESS_THROTTLE flags. The patch carries the necessary acks from the
relevant maintainers and is routed here as part of prctl()
thread-management."
* tag 'threads-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
prctl: PR_{G,S}ET_IO_FLUSHER to support controlling memory reclaim
sched.h: Annotate sighand_struct with __rcu
test: Add test for pidfd getfd
arch: wire up pidfd_getfd syscall
pid: Implement pidfd_getfd syscall
vfs, fdtable: Add fget_task helper
This Kselftest update for Linux 5.6-rc1 consists of several fixes to
framework and individual tests. In addition, it enables LKDTM tests
adding lkdtm target to kselftest Makefile.
-----BEGIN PGP SIGNATURE-----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=/7fF
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest update from Shuah Khan:
"This Kselftest update consists of several fixes to framework and
individual tests.
In addition, it enables LKDTM tests adding lkdtm target to kselftest
Makefile"
* tag 'linux-kselftest-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/ftrace: fix glob selftest
selftests: settings: tests can be in subsubdirs
kselftest: Minimise dependency of get_size on C library interfaces
selftests/livepatch: Remove unused local variable in set_ftrace_enabled()
selftests/livepatch: Replace set_dynamic_debug() with setup_config() in README
selftests/lkdtm: Add tests for LKDTM targets
selftests: Uninitialized variable in test_cgcore_proc_migration()
selftests: fix build behaviour on targets' failures
Pull openat2 support from Al Viro:
"This is the openat2() series from Aleksa Sarai.
I'm afraid that the rest of namei stuff will have to wait - it got
zero review the last time I'd posted #work.namei, and there had been a
leak in the posted series I'd caught only last weekend. I was going to
repost it on Monday, but the window opened and the odds of getting any
review during that... Oh, well.
Anyway, openat2 part should be ready; that _did_ get sane amount of
review and public testing, so here it comes"
From Aleksa's description of the series:
"For a very long time, extending openat(2) with new features has been
incredibly frustrating. This stems from the fact that openat(2) is
possibly the most famous counter-example to the mantra "don't silently
accept garbage from userspace" -- it doesn't check whether unknown
flags are present[1].
This means that (generally) the addition of new flags to openat(2) has
been fraught with backwards-compatibility issues (O_TMPFILE has to be
defined as __O_TMPFILE|O_DIRECTORY|[O_RDWR or O_WRONLY] to ensure old
kernels gave errors, since it's insecure to silently ignore the
flag[2]). All new security-related flags therefore have a tough road
to being added to openat(2).
Furthermore, the need for some sort of control over VFS's path
resolution (to avoid malicious paths resulting in inadvertent
breakouts) has been a very long-standing desire of many userspace
applications.
This patchset is a revival of Al Viro's old AT_NO_JUMPS[3] patchset
(which was a variant of David Drysdale's O_BENEATH patchset[4] which
was a spin-off of the Capsicum project[5]) with a few additions and
changes made based on the previous discussion within [6] as well as
others I felt were useful.
In line with the conclusions of the original discussion of
AT_NO_JUMPS, the flag has been split up into separate flags. However,
instead of being an openat(2) flag it is provided through a new
syscall openat2(2) which provides several other improvements to the
openat(2) interface (see the patch description for more details). The
following new LOOKUP_* flags are added:
LOOKUP_NO_XDEV:
Blocks all mountpoint crossings (upwards, downwards, or through
absolute links). Absolute pathnames alone in openat(2) do not
trigger this. Magic-link traversal which implies a vfsmount jump is
also blocked (though magic-link jumps on the same vfsmount are
permitted).
LOOKUP_NO_MAGICLINKS:
Blocks resolution through /proc/$pid/fd-style links. This is done
by blocking the usage of nd_jump_link() during resolution in a
filesystem. The term "magic-links" is used to match with the only
reference to these links in Documentation/, but I'm happy to change
the name.
It should be noted that this is different to the scope of
~LOOKUP_FOLLOW in that it applies to all path components. However,
you can do openat2(NO_FOLLOW|NO_MAGICLINKS) on a magic-link and it
will *not* fail (assuming that no parent component was a
magic-link), and you will have an fd for the magic-link.
In order to correctly detect magic-links, the introduction of a new
LOOKUP_MAGICLINK_JUMPED state flag was required.
LOOKUP_BENEATH:
Disallows escapes to outside the starting dirfd's
tree, using techniques such as ".." or absolute links. Absolute
paths in openat(2) are also disallowed.
Conceptually this flag is to ensure you "stay below" a certain
point in the filesystem tree -- but this requires some additional
to protect against various races that would allow escape using
"..".
Currently LOOKUP_BENEATH implies LOOKUP_NO_MAGICLINKS, because it
can trivially beam you around the filesystem (breaking the
protection). In future, there might be similar safety checks done
as in LOOKUP_IN_ROOT, but that requires more discussion.
In addition, two new flags are added that expand on the above ideas:
LOOKUP_NO_SYMLINKS:
Does what it says on the tin. No symlink resolution is allowed at
all, including magic-links. Just as with LOOKUP_NO_MAGICLINKS this
can still be used with NOFOLLOW to open an fd for the symlink as
long as no parent path had a symlink component.
LOOKUP_IN_ROOT:
This is an extension of LOOKUP_BENEATH that, rather than blocking
attempts to move past the root, forces all such movements to be
scoped to the starting point. This provides chroot(2)-like
protection but without the cost of a chroot(2) for each filesystem
operation, as well as being safe against race attacks that
chroot(2) is not.
If a race is detected (as with LOOKUP_BENEATH) then an error is
generated, and similar to LOOKUP_BENEATH it is not permitted to
cross magic-links with LOOKUP_IN_ROOT.
The primary need for this is from container runtimes, which
currently need to do symlink scoping in userspace[7] when opening
paths in a potentially malicious container.
There is a long list of CVEs that could have bene mitigated by
having RESOLVE_THIS_ROOT (such as CVE-2017-1002101,
CVE-2017-1002102, CVE-2018-15664, and CVE-2019-5736, just to name a
few).
In order to make all of the above more usable, I'm working on
libpathrs[8] which is a C-friendly library for safe path resolution.
It features a userspace-emulated backend if the kernel doesn't support
openat2(2). Hopefully we can get userspace to switch to using it, and
thus get openat2(2) support for free once it's ready.
Future work would include implementing things like
RESOLVE_NO_AUTOMOUNT and possibly a RESOLVE_NO_REMOTE (to allow
programs to be sure they don't hit DoSes though stale NFS handles)"
* 'work.openat2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Documentation: path-lookup: include new LOOKUP flags
selftests: add openat2(2) selftests
open: introduce openat2(2) syscall
namei: LOOKUP_{IN_ROOT,BENEATH}: permit limited ".." resolution
namei: LOOKUP_IN_ROOT: chroot-like scoped resolution
namei: LOOKUP_BENEATH: O_BENEATH-like scoped resolution
namei: LOOKUP_NO_XDEV: block mountpoint crossing
namei: LOOKUP_NO_MAGICLINKS: block magic-link resolution
namei: LOOKUP_NO_SYMLINKS: block symlink resolution
namei: allow set_root() to produce errors
namei: allow nd_jump_link() to produce errors
nsfs: clean-up ns_get_path() signature to return int
namei: only return -ECHILD from follow_dotdot_rcu()
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
Pull x86 cpu-features updates from Ingo Molnar:
"The biggest change in this cycle was a large series from Sean
Christopherson to clean up the handling of VMX features. This both
fixes bugs/inconsistencies and makes the code more coherent and
future-proof.
There are also two cleanups and a minor TSX syslog messages
enhancement"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/cpu: Remove redundant cpu_detect_cache_sizes() call
x86/cpu: Print "VMX disabled" error message iff KVM is enabled
KVM: VMX: Allow KVM_INTEL when building for Centaur and/or Zhaoxin CPUs
perf/x86: Provide stubs of KVM helpers for non-Intel CPUs
KVM: VMX: Use VMX_FEATURE_* flags to define VMCS control bits
KVM: VMX: Check for full VMX support when verifying CPU compatibility
KVM: VMX: Use VMX feature flag to query BIOS enabling
KVM: VMX: Drop initialization of IA32_FEAT_CTL MSR
x86/cpufeatures: Add flag to track whether MSR IA32_FEAT_CTL is configured
x86/cpu: Set synthetic VMX cpufeatures during init_ia32_feat_ctl()
x86/cpu: Print VMX flags in /proc/cpuinfo using VMX_FEATURES_*
x86/cpu: Detect VMX features on Intel, Centaur and Zhaoxin CPUs
x86/vmx: Introduce VMX_FEATURES_*
x86/cpu: Clear VMX feature flag if VMX is not fully enabled
x86/zhaoxin: Use common IA32_FEAT_CTL MSR initialization
x86/centaur: Use common IA32_FEAT_CTL MSR initialization
x86/mce: WARN once if IA32_FEAT_CTL MSR is left unlocked
x86/intel: Initialize IA32_FEAT_CTL MSR at boot
tools/x86: Sync msr-index.h from kernel sources
selftests, kvm: Replace manual MSR defs with common msr-index.h
...
test.d/ftrace/func-filter-glob.tc is failing on s390 because it has
ARCH_INLINE_SPIN_LOCK and friends set to 'y'. So the usual
__raw_spin_lock symbol isn't in the ftrace function list. Change
'*aw*lock' to '*spin*lock' which would hopefully match some of the
locking functions on all platforms.
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Pull RCU updates from Ingo Molnar:
"The RCU changes in this cycle were:
- Expedited grace-period updates
- kfree_rcu() updates
- RCU list updates
- Preemptible RCU updates
- Torture-test updates
- Miscellaneous fixes
- Documentation updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (69 commits)
rcu: Remove unused stop-machine #include
powerpc: Remove comment about read_barrier_depends()
.mailmap: Add entries for old paulmck@kernel.org addresses
srcu: Apply *_ONCE() to ->srcu_last_gp_end
rcu: Switch force_qs_rnp() to for_each_leaf_node_cpu_mask()
rcu: Move rcu_{expedited,normal} definitions into rcupdate.h
rcu: Move gp_state_names[] and gp_state_getname() to tree_stall.h
rcu: Remove the declaration of call_rcu() in tree.h
rcu: Fix tracepoint tracking RCU CPU kthread utilization
rcu: Fix harmless omission of "CONFIG_" from #if condition
rcu: Avoid tick_dep_set_cpu() misordering
rcu: Provide wrappers for uses of ->rcu_read_lock_nesting
rcu: Use READ_ONCE() for ->expmask in rcu_read_unlock_special()
rcu: Clear ->rcu_read_unlock_special only once
rcu: Clear .exp_hint only when deferred quiescent state has been reported
rcu: Rename some instance of CONFIG_PREEMPTION to CONFIG_PREEMPT_RCU
rcu: Remove kfree_call_rcu_nobatch()
rcu: Remove kfree_rcu() special casing and lazy-callback handling
rcu: Add support for debug_objects debugging for kfree_rcu()
rcu: Add multiple in-flight batches of kfree_rcu() work
...
- Time namespace support:
If a container migrates from one host to another then it expects that
clocks based on MONOTONIC and BOOTTIME are not subject to
disruption. Due to different boot time and non-suspended runtime these
clocks can differ significantly on two hosts, in the worst case time
goes backwards which is a violation of the POSIX requirements.
The time namespace addresses this problem. It allows to set offsets for
clock MONOTONIC and BOOTTIME once after creation and before tasks are
associated with the namespace. These offsets are taken into account by
timers and timekeeping including the VDSO.
Offsets for wall clock based clocks (REALTIME/TAI) are not provided by
this mechanism. While in theory possible, the overhead and code
complexity would be immense and not justified by the esoteric potential
use cases which were discussed at Plumbers '18.
The overhead for tasks in the root namespace (host time offsets = 0) is
in the noise and great effort was made to ensure that especially in the
VDSO. If time namespace is disabled in the kernel configuration the
code is compiled out.
Kudos to Andrei Vagin and Dmitry Sofanov who implemented this feature
and kept on for more than a year addressing review comments, finding
better solutions. A pleasant experience.
- Overhaul of the alarmtimer device dependency handling to ensure that
the init/suspend/resume ordering is correct.
- A new clocksource/event driver for Microchip PIT64
- Suspend/resume support for the Hyper-V clocksource
- The usual pile of fixes, updates and improvements mostly in the
driver code.
-----BEGIN PGP SIGNATURE-----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=x3qT
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-01-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The timekeeping and timers departement provides:
- Time namespace support:
If a container migrates from one host to another then it expects
that clocks based on MONOTONIC and BOOTTIME are not subject to
disruption. Due to different boot time and non-suspended runtime
these clocks can differ significantly on two hosts, in the worst
case time goes backwards which is a violation of the POSIX
requirements.
The time namespace addresses this problem. It allows to set offsets
for clock MONOTONIC and BOOTTIME once after creation and before
tasks are associated with the namespace. These offsets are taken
into account by timers and timekeeping including the VDSO.
Offsets for wall clock based clocks (REALTIME/TAI) are not provided
by this mechanism. While in theory possible, the overhead and code
complexity would be immense and not justified by the esoteric
potential use cases which were discussed at Plumbers '18.
The overhead for tasks in the root namespace (ie where host time
offsets = 0) is in the noise and great effort was made to ensure
that especially in the VDSO. If time namespace is disabled in the
kernel configuration the code is compiled out.
Kudos to Andrei Vagin and Dmitry Sofanov who implemented this
feature and kept on for more than a year addressing review
comments, finding better solutions. A pleasant experience.
- Overhaul of the alarmtimer device dependency handling to ensure
that the init/suspend/resume ordering is correct.
- A new clocksource/event driver for Microchip PIT64
- Suspend/resume support for the Hyper-V clocksource
- The usual pile of fixes, updates and improvements mostly in the
driver code"
* tag 'timers-core-2020-01-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
alarmtimer: Make alarmtimer_get_rtcdev() a stub when CONFIG_RTC_CLASS=n
alarmtimer: Use wakeup source from alarmtimer platform device
alarmtimer: Make alarmtimer platform device child of RTC device
alarmtimer: Update alarmtimer_get_rtcdev() docs to reflect reality
hrtimer: Add missing sparse annotation for __run_timer()
lib/vdso: Only read hrtimer_res when needed in __cvdso_clock_getres()
MIPS: vdso: Define BUILD_VDSO32 when building a 32bit kernel
clocksource/drivers/hyper-v: Set TSC clocksource as default w/ InvariantTSC
clocksource/drivers/hyper-v: Untangle stimers and timesync from clocksources
clocksource/drivers/timer-microchip-pit64b: Fix sparse warning
clocksource/drivers/exynos_mct: Rename Exynos to lowercase
clocksource/drivers/timer-ti-dm: Fix uninitialized pointer access
clocksource/drivers/timer-ti-dm: Switch to platform_get_irq
clocksource/drivers/timer-ti-dm: Convert to devm_platform_ioremap_resource
clocksource/drivers/em_sti: Fix variable declaration in em_sti_probe
clocksource/drivers/em_sti: Convert to devm_platform_ioremap_resource
clocksource/drivers/bcm2835_timer: Fix memory leak of timer
clocksource/drivers/cadence-ttc: Use ttc driver as platform driver
clocksource/drivers/timer-microchip-pit64b: Add Microchip PIT64B support
clocksource/drivers/hyper-v: Reserve PAGE_SIZE space for tsc page
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Commit 852c8cbf34 ("selftests/kselftest/runner.sh: Add 45 second
timeout per test") adds support for a new per-test-directory "settings"
file. But this only works for tests not in a sub-subdirectories, e.g.
- tools/testing/selftests/rtc (rtc) is OK,
- tools/testing/selftests/net/mptcp (net/mptcp) is not.
We have to increase the timeout for net/mptcp tests which are not
upstreamed yet but this fix is valid for other tests if they need to add
a "settings" file, see the full list with:
tools/testing/selftests/*/*/**/Makefile
Note that this patch changes the text header message printed at the end
of the execution but this text is modified only for the tests that are
in sub-subdirectories, e.g.
ok 1 selftests: net/mptcp: mptcp_connect.sh
Before we had:
ok 1 selftests: mptcp: mptcp_connect.sh
But showing the full target name is probably better, just in case a
subsubdir has the same name as another one in another subdirectory.
Fixes: 852c8cbf34 (selftests/kselftest/runner.sh: Add 45 second timeout per test)
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-01-27
The following pull-request contains BPF updates for your *net-next* tree.
We've added 20 non-merge commits during the last 5 day(s) which contain
a total of 24 files changed, 433 insertions(+), 104 deletions(-).
The main changes are:
1) Make BPF trampolines and dispatcher aware for the stack unwinder, from Jiri Olsa.
2) Improve handling of failed CO-RE relocations in libbpf, from Andrii Nakryiko.
3) Several fixes to BPF sockmap and reuseport selftests, from Lorenz Bauer.
4) Various cleanups in BPF devmap's XDP flush code, from John Fastabend.
5) Fix BPF flow dissector when used with port ranges, from Yoshiki Komachi.
6) Fix bpffs' map_seq_next callback to always inc position index, from Vasily Averin.
7) Allow overriding LLVM tooling for runqslower utility, from Andrey Ignatov.
8) Silence false-positive lockdep splats in devmap hash lookup, from Amol Grover.
9) Fix fentry/fexit selftests to initialize a variable before use, from John Sperbeck.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a simple test to make sure that a filter based on specified port
range classifies packets correctly.
Signed-off-by: Yoshiki Komachi <komachi.yoshiki@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Petar Penkov <ppenkov@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200117070533.402240-3-komachi.yoshiki@gmail.com
This test covers functionality and stability of the newly added
nftables set implementation supporting concatenation of ranged
fields.
For some selected set expression types, test:
- correctness, by checking that packets match or don't
- concurrency, by attempting races between insertion, deletion, lookup
- timeout feature, checking that packets don't match expired entries
and (roughly) estimate matching rates, comparing to baselines for
simple drop on netdev ingress hook and for hash and rbtrees sets.
In order to send packets, this needs one of sendip, netcat or bash.
To flood with traffic, iperf3, iperf and netperf are supported. For
performance measurements, this relies on the sample pktgen script
pktgen_bench_xmit_mode_netif_receive.sh.
If none of the tools suitable for a given test are available, specific
tests will be skipped.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There's limit of 40 programs tht can be attached
to trampoline for one function. Adding test that
tries to attach that many plus one extra that needs
to fail.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200123161508.915203-4-jolsa@kernel.org
Some newer cards supported by aacraid can take up to 40s to recover
after an EEH event. This causes spurious failures in the basic EEH
self-test since the current maximim timeout is only 30s.
Fix the immediate issue by bumping the timeout to a default of 60s,
and allow the wait time to be specified via an environmental variable
(EEH_MAX_WAIT).
Reported-by: Steve Best <sbest@redhat.com>
Suggested-by: Douglas Miller <dougmill@us.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200122031125.25991-1-oohall@gmail.com
Add a test that runs traffic across a port throttled with TBF. The test
checks that the observed throughput is within +-5% from the installed
shaper.
To allow checking both the software datapath and the offloaded one, make
the test suitable for inclusion from driver-specific wrapper. Introduce
such wrappers for mlxsw.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tc_rule_stats_get() fetches a packet counter of a given TC
rule. Extend it to support byte counters as well by adding an optional
argument with selector.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function busywait() is handy as a safety-latched variant of a while
loop. Many selftests deal specifically with counter values, and busywaiting
on them is likely to be rather common (it is not quite common now, but
busywait() has not been around for very long). To facilitate expressing
simply what is tested, introduce two helpers:
- until_counter_is(), which can be used as a predicate passed to
busywait(), which holds when expression, which is itself passed as an
argument to until_counter_is(), reaches a desired value.
- busywait_for_counter(), which is useful for waiting until a given counter
changes "by" (as opposed to "to") a certain amount.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function humanize() is used for converting value in bits/s to a
human-friendly approximate value in Kbps, Mbps or Gbps. There is nothing
hardware-specific in that, so move the function to lib.sh.
Similarly for the rate() function, which just does a bit of math to
calculate a rate, given two counter values and a time interval.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is a lot of false positives if a single reuseport test
fails. This is because expected_results and the result map are not cleared.
Zero both after individual test runs, which fixes the mentioned false
positives.
Fixes: 91134d849a ("bpf: Test BPF_PROG_TYPE_SK_REUSEPORT")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200124112754.19664-5-lmb@cloudflare.com
Include the name of the mismatching result in human readable format
when reporting an error. The new output looks like the following:
unexpected result
result: [1, 0, 0, 0, 0, 0]
expected: [0, 0, 0, 0, 0, 0]
mismatch on DROP_ERR_INNER_MAP (bpf_prog_linum:153)
check_results:FAIL:382
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200124112754.19664-4-lmb@cloudflare.com
The reuseport tests currently suffer from a race condition: FIN
packets count towards DROP_ERR_SKB_DATA, since they don't contain
a valid struct cmd. Tests will spuriously fail depending on whether
check_results is called before or after the FIN is processed.
Exit the BPF program early if FIN is set.
Fixes: 91134d849a ("bpf: Test BPF_PROG_TYPE_SK_REUSEPORT")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200124112754.19664-3-lmb@cloudflare.com
Use a proper temporary file for sendpage tests. This means that running
the tests doesn't clutter the working directory, and allows running the
test on read-only filesystems.
Fixes: 16962b2404 ("bpf: sockmap, add selftests")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200124112754.19664-2-lmb@cloudflare.com
Add mptcp_connect tool:
xmit two files back and forth between two processes, several net
namespaces including some adding delays, losses and reordering.
Wrapper script tests that data was transmitted without corruption.
The "-c" command line option for mptcp_connect.sh is there for debugging:
The script will use tcpdump to create one .pcap file per test case, named
according to the namespaces, protocols, and connect address in use.
For example, the first test case writes the capture to
ns1-ns1-MPTCP-MPTCP-10.0.1.1.pcap.
The stderr output from tcpdump is printed after the test completes to
show tcpdump's "packets dropped by kernel" information.
Also check that userspace can't create MPTCP sockets when mptcp.enabled
sysctl is off.
The "-b" option allows to tune/lower send buffer size.
"-m mmap" can be used to test blocking io. Default is non-blocking
io using read/write/poll.
Will run automatically on "make kselftest".
Note that the default timeout of 45 seconds is used even if there is a
"settings" changing it to 450. 45 seconds should be enough in most cases
but this depends on the machine running the tests.
A fix to correctly read the "settings" file has been proposed upstream
but not applied yet. It is not blocking the execution of these new tests
but it would be nice to have it:
https://patchwork.kernel.org/patch/11204935/
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detect when bpftool source code changes and trigger rebuild within
selftests/bpf Makefile. Also fix few small formatting problems.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200124054148.2455060-1-andriin@fb.com
The 'duration' variable is referenced in the CHECK() macro, and there are
some uses of the macro before 'duration' is set. The clang compiler
(validly) complains about this.
Sample error:
.../selftests/bpf/prog_tests/fexit_test.c:23:6: warning: variable 'duration' is uninitialized when used here [-Wuninitialized]
if (CHECK(err, "prog_load sched cls", "err %d errno %d\n", err, errno))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
.../selftests/bpf/test_progs.h:134:25: note: expanded from macro 'CHECK'
if (CHECK(err, "prog_load sched cls", "err %d errno %d\n", err, errno))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
_CHECK(condition, tag, duration, format)
^~~~~~~~
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200123235144.93610-1-sdf@google.com
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-01-22
The following pull-request contains BPF updates for your *net-next* tree.
We've added 92 non-merge commits during the last 16 day(s) which contain
a total of 320 files changed, 7532 insertions(+), 1448 deletions(-).
The main changes are:
1) function by function verification and program extensions from Alexei.
2) massive cleanup of selftests/bpf from Toke and Andrii.
3) batched bpf map operations from Brian and Yonghong.
4) tcp congestion control in bpf from Martin.
5) bulking for non-map xdp_redirect form Toke.
6) bpf_send_signal_thread helper from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a bpf_cubic example. Some highlights:
1. CONFIG_HZ .kconfig map is used.
2. In bictcp_update(), calculation is changed to use usec
resolution (i.e. USEC_PER_JIFFY) instead of using jiffies.
Thus, usecs_to_jiffies() is not used in the bpf_cubic.c.
3. In bitctcp_update() [under tcp_friendliness], the original
"while (ca->ack_cnt > delta)" loop is changed to the equivalent
"ca->ack_cnt / delta" operation.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200122233658.903774-1-kafai@fb.com
Add program extension tests that build on top of fexit_bpf2bpf tests.
Replace three global functions in previously loaded test_pkt_access.c program
with three new implementations:
int get_skb_len(struct __sk_buff *skb);
int get_constant(long val);
int get_skb_ifindex(int val, struct __sk_buff *skb, int var);
New function return the same results as original only if arguments match.
new_get_skb_ifindex() demonstrates that 'skb' argument doesn't have to be first
and only argument of BPF program. All normal skb based accesses are available.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200121005348.2769920-4-ast@kernel.org
During cross-compilation, it was discovered that LDFLAGS and
LDLIBS were not being used while building binaries, leading
to defaults which were not necessarily correct.
OpenEmbedded reported this kind of problem:
ERROR: QA Issue: No GNU_HASH in the ELF binary [...], didn't pass LDFLAGS?
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
To make sure no new files are introduced that doesn't include the bpf/
prefix in its #include, remove tools/lib/bpf from the include path
entirely.
Instead, we introduce a new header files directory under the scratch tools/
dir, and add a rule to run the 'install_headers' rule from libbpf to have a
full set of consistent libbpf headers in $(OUTPUT)/tools/include/bpf, and
then use $(OUTPUT)/tools/include as the include path for selftests.
For consistency we also make sure we put all the scratch build files from
other bpftool and libbpf into tools/build/, so everything stays within
selftests/.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/157952561246.1683545.2762245552022369203.stgit@toke.dk
Fix all selftests to include libbpf header files with the bpf/ prefix, to
be consistent with external users of the library. Also ensure that all
includes of exported libbpf header files (those that are exported on 'make
install' of the library) use bracketed includes instead of quoted.
To not break the build, keep the old include path until everything has been
changed to the new one; a subsequent patch will remove that.
Fixes: 6910d7d386 ("selftests/bpf: Ensure bpf_helper_defs.h are taken from selftests dir")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/157952560568.1683545.9649335788846513446.stgit@toke.dk
Add a VMLINUX_BTF variable with the locally-built path when calling the
runqslower Makefile from selftests. This makes sure a simple 'make'
invocation in the selftests dir works even when there is no BTF information
for the running kernel. Do a wildcard expansion and include the same paths
for BTF for the running kernel as in the runqslower Makefile, to make it
possible to build selftests without having a vmlinux in the local tree.
Also fix the make invocation to use $(OUTPUT)/tools as the destination
directory instead of $(CURDIR)/tools.
Fixes: 3a0d3092a4 ("selftests/bpf: Build runqslower from selftests")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/157952560344.1683545.2723631988771664417.stgit@toke.dk
The same with commit 4e59afbbed ("selftests/bpf: skip nmi test when perf
hw events are disabled"), it would make more sense to skip the
test_stacktrace_build_id_nmi test if the setup (e.g. virtual machines) has
disabled hardware perf events.
Fixes: 13790d1cc7 ("bpf: add selftest for stackmap with build_id in NMI context")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200117100656.10359-1-liuhangbin@gmail.com
After commit 0d13bfce02 ("libbpf: Don't require root for
bpf_object__open()") we no longer load BTF during bpf_object__open(),
so let's remove the expectation from test_btf that the fd is not -1.
The test currently fails.
Before:
BTF libbpf test[1] (test_btf_haskv.o): do_test_file:4152:FAIL bpf_object__btf_fd: -1
BTF libbpf test[2] (test_btf_newkv.o): do_test_file:4152:FAIL bpf_object__btf_fd: -1
BTF libbpf test[3] (test_btf_nokv.o): do_test_file:4152:FAIL bpf_object__btf_fd: -1
After:
BTF libbpf test[1] (test_btf_haskv.o): OK
BTF libbpf test[2] (test_btf_newkv.o): OK
BTF libbpf test[3] (test_btf_nokv.o): OK
Fixes: 0d13bfce02 ("libbpf: Don't require root for bpf_object__open()")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200118010546.74279-1-sdf@google.com
Test that the trap is triggered under the right conditions and that
devlink counters increase when action is trap.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that the trap is triggered under the right conditions and that
devlink counters increase.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that the trap is triggered under the right conditions and that
devlink counters increase.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test cases to check that packets routed through disabled RIFs and
packets routed from disabled RIFs are dropped and devlink counters
increase when the action is trap.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test all of the various openat2(2) flags. A small stress-test of a
symlink-rename attack is included to show that the protections against
".."-based attacks are sufficient.
The main things these self-tests are enforcing are:
* The struct+usize ABI for openat2(2) and copy_struct_from_user() to
ensure that upgrades will be handled gracefully (in addition,
ensuring that misaligned structures are also handled correctly).
* The -EINVAL checks for openat2(2) are all correctly handled to avoid
userspace passing unknown or conflicting flag sets (most
importantly, ensuring that invalid flag combinations are checked).
* All of the RESOLVE_* semantics (including errno values) are
correctly handled with various combinations of paths and flags.
* RESOLVE_IN_ROOT correctly protects against the symlink rename(2)
attack that has been responsible for several CVEs (and likely will
be responsible for several more).
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Alexei observed that test_progs send_signal may fail if run
with command line "./test_progs" and the tests will pass
if just run "./test_progs -n 40".
I observed similar issue with nmi subtest failure
and added a delay 100 us in Commit ab8b7f0cb3
("tools/bpf: Add self tests for bpf_send_signal_thread()")
and the problem is gone for me. But the issue still exists
in Alexei's testing environment.
The current code uses sample_freq = 50 (50 events/second), which
may not be enough. But if the sample_freq value is larger than
sysctl kernel/perf_event_max_sample_rate, the perf_event_open
syscall will fail.
This patch changed nmi perf testing to use sample_period = 1,
which means trying to sampling every event. This seems fixing
the issue.
Fixes: ab8b7f0cb3 ("tools/bpf: Add self tests for bpf_send_signal_thread()")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200116174004.1522812-1-yhs@fb.com
It was observed[1] on arm64 that __builtin_strlen led to an infinite
loop in the get_size selftest. This is because __builtin_strlen (and
other builtins) may sometimes result in a call to the C library
function. The C library implementation of strlen uses an IFUNC
resolver to load the most efficient strlen implementation for the
underlying machine and hence has a PLT indirection even for static
binaries. Because this binary avoids the C library startup routines,
the PLT initialization never happens and hence the program gets stuck
in an infinite loop.
On x86_64 the __builtin_strlen just happens to expand inline and avoid
the call but that is not always guaranteed.
Further, while testing on x86_64 (Fedora 31), it was observed that the
test also failed with a segfault inside write() because the generated
code for the write function in glibc seems to access TLS before the
syscall (probably due to the cancellation point check) and fails
because TLS is not initialised.
To mitigate these problems, this patch reduces the interface with the
C library to just the syscall function. The syscall function still
sets errno on failure, which is undesirable but for now it only
affects cases where syscalls fail.
[1] https://bugs.linaro.org/show_bug.cgi?id=5479
Signed-off-by: Siddhesh Poyarekar <siddhesh@gotplt.org>
Reported-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Tim Bird <tim.bird@sony.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit 35c9e74cff ("selftests/livepatch: Make dynamic debug setup and
restore generic") introduced setup_config() to set up the environment
for each test. It superseded set_dynamic_debug(). README still mentions
set_dynamic_debug(), so update it to setup_config() which should be used
now in every test.
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add ability to specify a list of test name substrings for selecting which
tests to run. So now -t is accepting a comma-separated list of strings,
similarly to how -n accepts a comma-separated list of test numbers.
Additionally, add ability to blacklist tests by name. Blacklist takes
precedence over whitelist. Blacklisting is important for cases where it's
known that some tests can't pass (e.g., due to perf hardware events that are
not available within VM). This is going to be used for libbpf testing in
Travis CI in its Github repo.
Example runs with just whitelist and whitelist + blacklist:
$ sudo ./test_progs -tattach,core/existence
#1 attach_probe:OK
#6 cgroup_attach_autodetach:OK
#7 cgroup_attach_multi:OK
#8 cgroup_attach_override:OK
#9 core_extern:OK
#10/44 existence:OK
#10/45 existence___minimal:OK
#10/46 existence__err_int_sz:OK
#10/47 existence__err_int_type:OK
#10/48 existence__err_int_kind:OK
#10/49 existence__err_arr_kind:OK
#10/50 existence__err_arr_value_type:OK
#10/51 existence__err_struct_type:OK
#10 core_reloc:OK
#19 flow_dissector_reattach:OK
#60 tp_attach_query:OK
Summary: 8/8 PASSED, 0 SKIPPED, 0 FAILED
$ sudo ./test_progs -tattach,core/existence -bcgroup,flow/arr
#1 attach_probe:OK
#9 core_extern:OK
#10/44 existence:OK
#10/45 existence___minimal:OK
#10/46 existence__err_int_sz:OK
#10/47 existence__err_int_type:OK
#10/48 existence__err_int_kind:OK
#10/51 existence__err_struct_type:OK
#10 core_reloc:OK
#60 tp_attach_query:OK
Summary: 4/6 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Julia Kartseva <hex@fb.com>
Link: https://lore.kernel.org/bpf/20200116005549.3644118-1-andriin@fb.com
Add a test that will attach a FENTRY and FEXIT program to the XDP test
program. It will also verify data from the XDP context on FENTRY and
verifies the return code on exit.
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/157909410480.47481.11202505690938004673.stgit@xdp-tutorial
The test_progs send_signal() is amended to test
bpf_send_signal_thread() as well.
$ ./test_progs -n 40
#40/1 send_signal_tracepoint:OK
#40/2 send_signal_perf:OK
#40/3 send_signal_nmi:OK
#40/4 send_signal_tracepoint_thread:OK
#40/5 send_signal_perf_thread:OK
#40/6 send_signal_nmi_thread:OK
#40 send_signal:OK
Summary: 1/6 PASSED, 0 SKIPPED, 0 FAILED
Also took this opportunity to rewrite the send_signal test
using skeleton framework and array mmap to make code
simpler and more readable.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200115035003.602425-1-yhs@fb.com
Mausezahn does not recognize "own" as a keyword on source IP address. As a
result, the MC stream is not running at all, and therefore no UC
degradation can be observed even in principle.
Fix the invocation, and tighten the test: due to the minimum shaper
configured at the MC TCs, we always expect about 20% degradation. Fail the
test if it is lower.
Fixes: 573363a68f ("selftests: mlxsw: Add qos_lib.sh")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reported-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test reuses the common FIB offload tests in order to make sure that
mlxsw correctly implements FIB offload.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test various aspects of the FIB offload API on top of the netdevsim
implementation. Both good and bad flows are tested.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a set of common helpers and tests for FIB offload that can be
used by multiple drivers to check their FIB offload implementations.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output on success:
1..1
ok 1 exec
# Pass 1 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0
Output on failure:
1..1
not ok 1 36016 16
Bail out!
Output with lack of permissions:
1..1
not ok 1 # SKIP need to run as root
Output without support of time namespaces:
1..1
not ok 1 # SKIP Time namespaces are not supported
Co-developed-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191112012724.250792-35-dima@arista.com
Output on success:
1..4
ok 1 host: clock: monotonic cycles: 148323947
ok 2 host: clock: boottime cycles: 148577503
ok 3 ns: clock: monotonic cycles: 137659217
ok 4 ns: clock: boottime cycles: 137959154
# Pass 4 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0
Output with lack of permissions:
1..4
ok 1 host: clock: monotonic cycles: 145671139
ok 2 host: clock: boottime cycles: 146958357
not ok 3 # SKIP need to run as root
Output without support of time namespaces:
1..4
ok 1 host: clock: monotonic cycles: 145671139
ok 2 host: clock: boottime cycles: 146958357
not ok 3 # SKIP Time namespaces are not supported
Co-developed-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191112012724.250792-34-dima@arista.com
Check that timer_create() takes into account clock offsets.
Output on success:
1..3
ok 1 clockid=7
ok 2 clockid=1
ok 3 clockid=9
# Pass 3 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0
Output with lack of permissions:
1..3
not ok 1 # SKIP need to run as root
Output without support of time namespaces:
1..3
not ok 1 # SKIP Time namespaces are not supported
Co-developed-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191112012724.250792-33-dima@arista.com
Check that /proc/uptime is correct inside a new time namespace.
Output on success:
1..1
ok 1 Passed for /proc/uptime
# Pass 1 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0
Output with lack of permissions:
1..1
not ok 1 # SKIP need to run as root
Output without support of time namespaces:
1..1
not ok 1 # SKIP Time namespaces are not supported
Co-developed-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191112012724.250792-32-dima@arista.com
Check that clock_nanosleep() takes into account clock offsets.
Output on success:
1..4
ok 1 clockid: 1 abs:0
ok 2 clockid: 1 abs:1
ok 3 clockid: 9 abs:0
ok 4 clockid: 9 abs:1
Output with lack of permissions:
1..4
not ok 1 # SKIP need to run as root
Output without support of time namespaces:
1..4
not ok 1 # SKIP Time namespaces are not supported
Co-developed-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191112012724.250792-31-dima@arista.com
Check that timerfd_create() takes into account clock offsets.
Output on success:
1..3
ok 1 clockid=7
ok 2 clockid=1
ok 3 clockid=9
# Pass 3 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0
Output on failure:
1..3
not ok 1 clockid: 7 elapsed: 0
not ok 2 clockid: 1 elapsed: 0
not ok 3 clockid: 9 elapsed: 0
Bail out!
Output with lack of permissions:
1..3
not ok 1 # SKIP need to run as root
Output without support of time namespaces:
1..3
not ok 1 # SKIP Time namespaces are not supported
Co-developed-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191112012724.250792-30-dima@arista.com
A test to check that all supported clocks work on host and inside
a new time namespace. Use both ways to get time: through VDSO and
by entering the kernel with implicit syscall.
Introduce a new timens directory in selftests framework for
the next timens tests.
Output on success:
1..10
ok 1 Passed for CLOCK_BOOTTIME (syscall)
ok 2 Passed for CLOCK_BOOTTIME (vdso)
ok 3 Passed for CLOCK_BOOTTIME_ALARM (syscall)
ok 4 Passed for CLOCK_BOOTTIME_ALARM (vdso)
ok 5 Passed for CLOCK_MONOTONIC (syscall)
ok 6 Passed for CLOCK_MONOTONIC (vdso)
ok 7 Passed for CLOCK_MONOTONIC_COARSE (syscall)
ok 8 Passed for CLOCK_MONOTONIC_COARSE (vdso)
ok 9 Passed for CLOCK_MONOTONIC_RAW (syscall)
ok 10 Passed for CLOCK_MONOTONIC_RAW (vdso)
# Pass 10 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0
Output with lack of permissions:
1..10
not ok 1 # SKIP need to run as root
Output without support of time namespaces:
1..10
not ok 1 # SKIP Time namespaces are not supported
Co-developed-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191112012724.250792-29-dima@arista.com
Bring selftest/bpf's Makefile output to the same format used by libbpf and
bpftool: 2 spaces of padding on the left + 8-character left-aligned build step
identifier.
Also, hide feature detection output by default. Can be enabled back by setting
V=1.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200113073143.1779940-4-andriin@fb.com
The following tests:
* Fetch FD, and then compare via kcmp
* Make sure getfd can be blocked by blocking ptrace_may_access
* Making sure fetching bad FDs fails
* Make sure trying to set flags to non-zero results in an EINVAL
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20200107175927.4558-5-sargun@sargun.me
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Sync msr-index.h to pull in recent renames of the IA32_FEATURE_CONTROL
MSR definitions. Update KVM's VMX selftest and turbostat accordingly.
Keep the full name in turbostat's output to avoid breaking someone's
workflow, e.g. if a script is looking for the full name.
While using the renamed defines is by no means necessary, do the sync
now to avoid leaving a landmine that will get stepped on the next time
msr-index.h needs to be refreshed for some other reason.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20191221044513.21680-4-sean.j.christopherson@intel.com
The kernel's version of msr-index.h was pulled wholesale into tools by
commit
444e2ff34d ("tools arch x86: Grab a copy of the file containing the MSR numbers"),
Use the common msr-index.h instead of manually redefining everything in
a KVM-only header.
Note, a few MSR-related definitions remain in processor.h because they
are not covered by msr-index.h, including the awesomely named
APIC_BASE_MSR, which refers to starting index of the x2APIC MSRs, not
the actual MSR_IA32_APICBASE, which *is* defined by msr-index.h.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20191221044513.21680-3-sean.j.christopherson@intel.com
Streamline BPF_TRACE_x macro by moving out return type and section attribute
definition out of macro itself. That makes those function look in source code
similar to other BPF programs. Additionally, simplify its usage by determining
number of arguments automatically (so just single BPF_TRACE vs a family of
BPF_TRACE_1, BPF_TRACE_2, etc). Also, allow more natural function argument
syntax without commas inbetween argument type and name.
Given this helper is useful not only for tracing tp_btf/fenty/fexit programs,
but could be used for LSM programs and others following the same pattern,
rename BPF_TRACE macro into more generic BPF_PROG. Existing BPF_TRACE_x
usages in selftests are converted to new BPF_PROG macro.
Following the same pattern, define BPF_KPROBE and BPF_KRETPROBE macros for
nicer usage of kprobe/kretprobe arguments, respectively. BPF_KRETPROBE, adopts
same convention used by fexit programs, that last defined argument is probed
function's return result.
v4->v5:
- fix test_overhead test (__set_task_comm is void) (Alexei);
v3->v4:
- rebased and fixed one more BPF_TRACE_x occurence (Alexei);
v2->v3:
- rename to shorter and as generic BPF_PROG (Alexei);
v1->v2:
- verified GCC handles pragmas as expected;
- added descriptions to macros;
- converted new STRUCT_OPS selftest to BPF_HANDLER (worked as expected);
- added original context as 'ctx' parameter, for cases where it has to be
passed into BPF helpers. This might cause an accidental naming collision,
unfortunately, but at least it's easy to work around. Fortunately, this
situation produces quite legible compilation error:
progs/bpf_dctcp.c:46:6: error: redefinition of 'ctx' with a different type: 'int' vs 'unsigned long long *'
int ctx = 123;
^
progs/bpf_dctcp.c:42:6: note: previous definition is here
void BPF_HANDLER(dctcp_init, struct sock *sk)
^
./bpf_trace_helpers.h:58:32: note: expanded from macro 'BPF_HANDLER'
____##name(unsigned long long *ctx, ##args)
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200110211634.1614739-1-andriin@fb.com
This adds a basic framework for running all the "safe" LKDTM tests. This
will allow easy introspection into any selftest logs to examine the
results of most LKDTM tests.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
test_global_func[12] - check 512 stack limit.
test_global_func[34] - check 8 frame call chain limit.
test_global_func5 - check that non-ctx pointer cannot be passed into
a function that expects context.
test_global_func6 - check that ctx pointer is unmodified.
test_global_func7 - check that global function returns scalar.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200110064124.1760511-7-ast@kernel.org
Make two static functions in test_xdp_noinline.c global:
before: processed 2790 insns
after: processed 2598 insns
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200110064124.1760511-6-ast@kernel.org
test results:
pyperf50 with always_inlined the same function five times: processed 46378 insns
pyperf50 with global function: processed 6102 insns
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200110064124.1760511-5-ast@kernel.org
Carlos Neira