This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.
Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle). Otherwise the handler is
reentered over and over again.
The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared. Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'. Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If rx_urb allocation fails in mcs_setup_urbs(), tx_urb leaks.
If mcs_receive_start() fails in mcs_net_open(), the both urbs are not deallocated.
The patch fixes the issues and by the way fixes label indentation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is down, CQs are freed. We must check the device state
to avoid issuing firmware commands on non existing CQs.
CC: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/dec/tulip/de4x5.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/amd/sun3lance.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/ibm/ehea/ehea_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/adi/bfin_mac.c.
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VM is providing an iSCSI target and the LUN is used by the
backend domain, the generated skbs for direct I/O writes to the disk
have large, multi-page skb->data but no frags.
With some lengths and starting offsets, xen_netbk_count_skb_slots()
would be one short because the simple calculation of
DIV_ROUND_UP(skb_headlen(), PAGE_SIZE) was not accounting for the
decisions made by start_new_rx_buffer() which does not guarantee
responses are fully packed.
For example, a skb with length < 2 pages but which spans 3 pages would
be counted as requiring 2 slots but would actually use 3 slots.
skb->data:
| 1111|222222222222|3333 |
Fully packed, this would need 2 slots:
|111122222222|22223333 |
But because the 2nd page wholy fits into a slot it is not split across
slots and goes into a slot of its own:
|1111 |222222222222|3333 |
Miscounting the number of slots means netback may push more responses
than the number of available requests. This will cause the frontend
to get very confused and report "Too many frags/slots". The frontend
never recovers and will eventually BUG.
Fix this by counting the number of required slots more carefully. In
xen_netbk_count_skb_slots(), more closely follow the algorithm used by
xen_netbk_gop_skb() by introducing xen_netbk_count_frag_slots() which
is the dry-run equivalent of netbk_gop_frag_copy().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 989038e217 ("tg3: Don't turn off
led on 5719 serdes port 0") added code to skip turning led off on port
0 of the 5719 since it powered down other ports. This workaround needs
to be enabled on the 5720 as well.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c8d68e6be1
(tuntap: multiqueue support) only call free_netdev() on error in
tun_set_iff(). This causes several issues:
- memory of tun security were leaked
- use after free since the flow gc timer was not deleted and the tfile
were not detached
This patch solves the above issues.
Reported-by: Wannes Rombouts <wannes.rombouts@epitech.eu>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure a format string cannot accidentally leak into the
kthread_run() call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control is defined in the four EEPROM sections but the driver only reads
from section 0.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where some ports can fail to initialize on a
cold boot. This patch adds an additional call to read the PHY id for i354
devices in order workaround the hardware problem.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is a pull request for a few early fixes for the 3.12 stream.
Alexey Khoroshilov corrects a use-after-free issue on rtl8187 found
by the Linux Driver Verification project.
Arend van Spriel provides a brcmfmac patch to fix a build issue
reported by Randy Dunlap.
Hauke Mehrtens offers a bcma fix to properly account for the storage
width of error code values before checking them.
Solomon Peachy brings a pair of cw1200 fixes to avoid hangs in that
driver with SPI devices. One avoids transfers in interrupt context,
the other fixes a locking issue.
Stanislaw Gruszka changes the initialization of the rt2800 driver to
avoid a freeze, addressing a bug in the Red Hat bugzilla.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Same narrative as eb2dc35d99 ("r8169: RxConfig
hack for the 8168evl.") regarding AMD IOMMU errors.
RTL_GIGA_MAC_VER_36 - 8168f as well - has not been reported to behave the
same.
Tested-by: David R <david@unsolicited.net>
Tested-by: Frédéric Leroy <fredo@starox.org>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the device list from the Windows driver description files
included with a new Qualcomm MDM9615 based device, "Alcatel-sbell
ASB TL131 TDD LTE", from China Mobile. This device is tested
and verified to work. The others are assumed to work based on
using the same Windows driver.
Many of these devices support multiple QMI/wwan ports, requiring
multiple interface matching entries. All devices are composite,
providing a mix of one or more serial, storage or Android Debug
Brigde functions in addition to the wwan function.
This device list included an update of one previously known device,
which was incorrectly assumed to have a Gobi 2K layout. This is
corrected.
Reported-by: 王康 <scateu@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series implements the new i40e driver for Intel's upcoming
Intel(R) Ethernet Controller XL710 Family of devices.
V7: many changes from a few comments:
use linux errno types
change I40E_SUCCESS to 0, standardize returns
change s32 return values to int
use void return values where possible
prefer use of int over i40e_status
V6: rename Kbuild to Makefile
rename i40e_mem[set|cpy] to regular memset/memcpy
V5: remove sysfs support from this set, will rearchitect
changes from community comments
V4: addresses remaining community comments, mostly trivial edits.
major sparse based cleanup of possible endian issues
removal of most of __func__ references
sizeof(*var) instead of sizeof(struct ...)
change 'NULL ==' tests to !NULL
implement xps
use kernel bitshift macros (upper_32_bits, etc)
V3: many more individual comments addressed, thanks reviewers! Many
other changes due to internal review and development.
V2: each patch has individual comments, in general, feedback from the
list was applied and addressed. Many changes due to internal review
and coding as well.
V1: initial send
Let me start by saying thanks and we appreciate any time spent by
those of you who review and comment on this new driver, and we will
attempt to address and respond to all issues brought to our attention.
I tried to break the patches up to ease review, but the series should
apply and still be bisectable, as the last patch adds the driver to
the kernel compile with CONFIG_I40E.
This driver is for a brand new bit of silicon that has a different
design than other Intel Ethernet silicon, and therefore needed a new
driver.
The hardware has quite a bit of capability and this driver is only
meant to provide basic functionality at first. Future patches will
continue to add functionality and bug fixes.
This initial release is very early in the product cycle with the intent
of getting initial support into the kernel before users have the
hardware available to purchase. A software development manual is not
ready yet but will be available when the hardware ships.
The driver development model and interaction with community submitted
patches *will not be any different* than what we are currently doing
today. We plan to continue established processes.
An associated i40evf driver has been posted for review.
List of tools we ran in preparation:
way more sparse clean
make W=1, W=2 clean
checkpatch (almost) clean
total: 1 errors, 4 warnings, 30461 lines checked
NOTE: Ignored message types: LONG_LINE
- issues have been addressed and the remainders
are noise.
codespell clean
smatch (almost) clean with a couple minor warnings
coccicheck clean
namespacecheck clean
allmodconfig clean
ppc64 build clean (untested)
This driver is a team effort, thank you to Joseph Gasparakis,
Shannon Nelson, Anjali Singhai-Jain, Mitch Williams, Neerav
Parikh, Vasu Dev, Kavindya Deegala, Yi Zou, and PJ Waskiewicz.
TODO (known issues)
BQL implementation
finish rtnl_stat64 locking (we have a patch but debugging it)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The "id" variable was being incremented in common code, but only
initialized and used in IPv4 code. We move the increment to the IPv4
code too, and then legitimately use the uninitialized_var() macro to
avoid the gcc 4.6 warning that 'id' may be used uninitialized.
Note that gcc 4.7 does not warn.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/broadcom/bcm63xx_enet.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/korina.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently macvlan calls skb_clone in macvlan_broadcast but checks
for a NULL return in macvlan_broadcast_one instead. This is
needlessly confusing and may lead to bugs introduced later.
This patch moves the error check to where the skb_clone call is.
The only other caller of macvlan_broadcast_one never passes in a
NULL value so it doesn't need the check either.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c: In function 'qlcnic_handle_fw_message':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:922:4: warning: overflow in implicit constant conversion [-Woverflow]
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We make bond_arp_rcv global so it can be used in bond_sysfs if the bond
interface is up and arp_interval is being changed to a positive value
and cleared otherwise as per Jay's suggestion.
This also fixes a problem where bond_arp_rcv was set even though
arp_validate was disabled while the bond was up by unsetting recv_probe
in bond_store_arp_validate and respectively setting it if enabled.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to protect store_arp_validate via rtnl because it can race with
mode changing and we can end up having arp_validate set in a mode
different from active-backup.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization bnx2x allocates significant amounts of memory
(for rx data, rx SGEs, TPA pool) using atomic allocations.
I received a report where bnx2x failed to allocate SGEs and it had
to fall back to TPA-less operation.
Let's use GFP_KERNEL allocations during initialization, which runs
in process context. Add gfp_t parameters to functions that are used
both in initialization and in the receive path.
Use an unlikely branch in bnx2x_frag_alloc() to avoid atomic allocation
by netdev_alloc_frag(). The branch is taken several thousands of times
during initialization, but then never more. Note that fp->rx_frag_size
is never greater than PAGE_SIZE, so __get_free_page() can be used here.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After an MC reboot, the datapath may be running a different firmware
variant and have different capabilities. It is critical that we know
the current capabilities so that we can pass valid flags to
MC_CMD_INIT_EVQ.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Rename efx_ef10_init_capabilities() to the more specific
efx_ef10_init_datapath_caps().
Stop accepting short responses to MC_CMD_GET_CAPABILITIES; we
don't need to support pre-production firmware.
Move the check for RX prefix support from efx_ef10_probe() into
efx_ef10_init_datapath_caps() and use consistent error messages
for missing TSO support and missing RX prefix support.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
If the MC reboots then the stats it reports to us will have been
reset. We need to reset ours to get efx_update_diff_stat() working
properly.
(This is a re-run of commit 876be083b6 'sfc: Reset driver's
MAC stats after MC reboot seen'.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Unlike Siena where timestamping is provided by a peripheral, EF10
delivers RX timestamps in the packet prefix. However the driver
doesn't yet support this.
We are also creating a PHC device for each EF10 function, even though
the clock is really shared between all of them.
Disable hardware PTP/timestamping support until it's complete.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This patch adds the changes for Kconfig, i40e.txt, MAINTAINERS, Kbuild
and new i40e/Makefile to build i40e with the kernel.
New driver build option is CONFIG_I40E
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This driver includes a debugfs interface for developers to get more hardware
information in real-time.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While not part of this patch series, an i40evf driver is on its
way, and uses these files to communicate to the PF driver.
This patch contains the header and implementation files for the
PF to VF interface.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the main driver header files, containing
structures and data types specific to the linux driver.
i40e_osdep.h contains some code that helps us adapt our OS agnostic code to
Linux.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the ethtool interface and implementation.
The goal in this patch series is minimal functionality while not
including much in the way of "set support."
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains the transmit, receive, and NAPI routines, as well
as ancillary routines.
This file is code that is (will be) used by both the VF and PF
drivers.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the driver for the Intel(R) Ethernet Controller XL710 Family.
This driver is targeted at basic ethernet functionality only, and will be
improved upon further as time goes on.
This patch contains the driver entry points but does not include transmit
and receive (see the next patch in the series) routines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of VF RSS feature doorbell block was configured not to use dpm, but
a small part of configuration was left out, preventing the driver from sending
tx messages to the device. This patch adds the missing configuration.
Reported-by: Eric Dumazet <eric.dumazet@gmil.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My commit
commit c630ccf1a1
Author: Stanislaw Gruszka <stf_xl@wp.pl>
Date: Sat Mar 16 19:19:46 2013 +0100
rt2800: rearrange bbp/rfcsr initialization
make Maxim machine freeze when try to start wireless device.
Initialization order and sending MCU_BOOT_SIGNAL request, changed in
above commit, is important. Doing things incorrectly make PCIe bus
problems, which can froze the machine.
This patch change initialization sequence like vendor driver do:
function NICInitializeAsic() from
2011_1007_RT5390_RT5392_Linux_STA_V2.5.0.3_DPO (PCI devices) and
DPO_RT5572_LinuxSTA_2.6.1.3_20121022 (according Mediatek, latest driver
for RT8070/RT3070/RT3370/RT3572/RT5370/RT5372/RT5572 USB devices).
It fixes freezes on Maxim system.
Resolve:
https://bugzilla.redhat.com/show_bug.cgi?id=1000679
Reported-and-tested-by: Maxim Polyakov <polyakov@dexmalabs.com>
Bisected-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of __dev_alloc_skb() failure rtl8187_init_urbs()
calls usb_free_urb(entry) where 'entry' can points to urb
allocated at the previous iteration. That means refcnt will be
decremented incorrectly and the urb can be used after memory
deallocation.
The patch fixes the issue and implements error handling of init_urbs
in rtl8187_start().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kernel configuration for the driver could result in
compilation issues as reported by Randy Dunlap. His results
are show below:
"on x86_64:
when
CONFIG_MMC=m
CONFIG_BRCMUTIL=y
CONFIG_BRCMFMAC=y
CONFIG_BRCMFMAC_SDIO=y
This bool kconfig symbol:
config BRCMFMAC_SDIO
bool "SDIO bus interface support for FullMAC driver"
depends on MMC
allows BRCMFMAC_SDIO to be y even when MMC=m.
Is there a reasonable solution to this?
This causes many build errors:
drivers/built-in.o: In function `brcmf_sdio_assert_info':
dhd_sdio.c:(.text+0x39609b): undefined reference to `sdio_claim_host'
dhd_sdio.c:(.text+0x3960d9): undefined reference to `sdio_release_host'
drivers/built-in.o: In function `brcmf_sdio_readframes':
dhd_sdio.c:(.text+0x396a62): undefined reference to `sdio_claim_host'
dhd_sdio.c:(.text+0x396a9b): undefined reference to `sdio_release_host'
..."
This patch adds the appropriate logic in Kconfig to resolve
these issues. The solution was provided by Hauke Mehrtens.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cw1200_spi driver tries to mirror the cw1200_sdio driver's lock
API, which relies on sdio_claim_host/sdio_release_host to serialize
hardware operations across multiple threads.
Unfortunately the implementation was flawed, as it lacked a way to wake
up the lock requestor when there was contention, often resulting in a
hang.
This problem was uncovered while trying to fix the
spi-transfers-in-interrupt-context BUG() corrected in the previous
patch. Many thanks to Dave Sizeburns for his assistance in fixing this.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we get an interrupt from the hardware, the first thing the driver does
is tell the device to mask off the interrupt line. Unfortunately this
involves a SPI transaction in interrupt context. Some (most?) SPI
controllers perform the transfer asynchronously and try to sleep.
This is bad, and triggers a BUG().
So, work around this by using adding a hwbus hook for the cw1200 driver
core to call. The cw1200_spi driver translates this into
irq_disable()/irq_enable() calls instead, which can safely be called in
interrupt context.
Apparently the platforms I used to develop the cw1200_spi driver used
synchronous spi_sync() implementations, which is why this didn't surface
until now.
Many thanks to Dave Sizeburns for the inital bug report and his services
as a tester.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking fixes from David Miller:
"A quick set of fixes, some to deal with fallout from yesterday's
net-next merge.
1) Fix compilation of bnx2x driver with CONFIG_BNX2X_SRIOV disabled,
from Dmitry Kravkov.
2) Fix a bnx2x regression caused by one of Dave Jones's mistaken
braces changes, from Eilon Greenstein.
3) Add some protective filtering in the netlink tap code, from Daniel
Borkmann.
4) Fix TCP congestion window growth regression after timeouts, from
Yuchung Cheng.
5) Correctly adjust TCP's rcv_ssthresh for out of order packets, from
Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tcp: properly increase rcv_ssthresh for ofo packets
net: add documentation for BQL helpers
mlx5: remove unused MLX5_DEBUG param in Kconfig
bnx2x: Restore a call to config_init
bnx2x: fix broken compilation with CONFIG_BNX2X_SRIOV is not set
tcp: fix no cwnd growth after timeout
net: netlink: filter particular protocols from analyzers
This patch proposes to remove the MLX5_DEBUG kernel configuration
parameter defined in drivers/net/ethernet/mellanox/mlx5/core/Kconfig,
but used nowhere in the makefiles and source code.
This could also be fixed by using this parameter,
but this may be a leftover from driver development...
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c0a77ec74f 'bnx2x: Add missing braces in
bnx2x:bnx2x_link_initialize' identified indentation problem, but resolved it
by adding braces instead of fixing the indentation. The braces now prevents a
config_init call in some cases, though it should be called regardless of that
condition. This patch removes the braces and fix the confusing indentation
that caused this mess.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
CC: Dave Jones <davej@redhat.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 60cad4e67b
"bnx2x: VF RSS support - VF side" fails to compile w/o
CONFIG_BNX2X_SRIOV option.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
Merge commit 06c54055be did a bad conflict resolution accidentally
leaving out a closing brace. Add it back.
This breaks a handful of defconfigs on ARM, so it'd be good to see it
applied pretty quickly.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Accept and handle 40G link events.
Accept ethtool link settings of speed == 40000 && duplex, and set the
appropriate MCDI PHY capability.
This does not include reporting of 40G media types, as those have not
yet been assigned numbers in the MCDI protocol.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
The indentation here implies that the intent was for this to be a multiline if.
Introduced a few years ago in commit ec146a6f01 ("bnx2x: Modify XGXS functions")
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements the ->ndo_do_ioctl() operation so that the
PHY-related ioctl() calls can work from userspace, which allows
applications like mii-tool or mii-diag to do their job.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes a long-standing bug that has been reported by many
users: on some Armada 370 platforms, only the network interface that
has been used in U-Boot to tftp the kernel works properly in
Linux. The other network interfaces can see a 'link up', but are
unable to transmit data. The reports were generally made on the Armada
370-based Mirabox, but have also been given on the Armada 370-RD
board.
The network MAC in the Armada 370/XP (supported by the mvneta driver
in Linux) has a functionality that allows it to continuously poll the
PHY and directly update the MAC configuration accordingly (speed,
duplex, etc.). The very first versions of the driver submitted for
review were using this hardware mechanism, but due to this, the driver
was not integrated with the kernel phylib. Following reviews, the
driver was changed to use the phylib, and therefore a software based
polling. In software based polling, Linux regularly talks to the PHY
over the MDIO bus, and sees if the link status has changed. If it's
the case then the adjust_link() callback of the driver is called to
update the MAC configuration accordingly.
However, it turns out that the adjust_link() callback was not
configuring the hardware in a completely correct way: while it was
setting the speed and duplex bits correctly, it wasn't telling the
hardware to actually take into account those bits rather than what the
hardware-based PHY polling mechanism has concluded. So, in fact the
adjust_link() callback was basically a no-op.
However, the network happened to be working because on the network
interfaces used by U-Boot for tftp on Armada 370 platforms because the
hardware PHY polling was enabled by the bootloader, and left enabled
by Linux. However, the second network interface not used for tftp (or
both network interfaces if the kernel is loaded from USB, NAND or SD
card) didn't had the hardware PHY polling enabled.
This patch fixes this situation by:
(1) Making sure that the hardware PHY polling is disabled by clearing
the MVNETA_PHY_POLLING_ENABLE bit in the MVNETA_UNIT_CONTROL
register in the driver ->probe() function.
(2) Making sure that the duplex and speed selections made by the
adjust_link() callback are taken into account by clearing the
MVNETA_GMAC_AN_SPEED_EN and MVNETA_GMAC_AN_DUPLEX_EN bits in the
MVNETA_GMAC_AUTONEG_CONFIG register.
This patch has been tested on Armada 370 Mirabox, and now both network
interfaces are usable after boot.
[ Problem introduced by commit c5aff18 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") ]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Jochen De Smet <jochen.armkernel@leahnim.org>
Cc: Peter Sanford <psanford@nearbuy.io>
Cc: Ethan Tuttle <ethan@ethantuttle.com>
Cc: Chény Yves-Gael <yves@cheny.fr>
Cc: Ryan Press <ryan@presslab.us>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: vdonnefort@lacie.com
Cc: stable@vger.kernel.org
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Vincent Donnefort <vdonnefort@gmail.com>
Tested-by: Yves-Gael Cheny <yves@cheny.fr>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the __LINK_STATE_START check to verify the device is running, in
favor of netif_running(). netif_running() performs the same check of
__LINK_STATE_START, so the code should behave the same.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Sorbica Shieh <sorbica@icplus.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
copying large files to a NFS mounted host was taking absurdly large
time.
Turns out that TX BD reclaim had a sublte bug.
Loop starts off from @txbd_dirty cursor and stops when it hits a BD
still in use by controller. However when it stops it needs to keep the
cursor at that very BD to resume scanning in next iteration. However it
was erroneously incrementing the cursor, causing the next scan(s) to
fail too, unless the BD chain was completely drained out.
[ARCLinux]$ ls -l -sh /disk/log.txt
17976 -rw-r--r-- 1 root root 17.5M Sep /disk/log.txt
========== Before =====================
[ARCLinux]$ time cp /disk/log.txt /mnt/.
real 31m 7.95s
user 0m 0.00s
sys 0m 0.10s
========== After =====================
[ARCLinux]$ time cp /disk/log.txt /mnt/.
real 0m 24.33s
user 0m 0.00s
sys 0m 0.19s
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com> (commit_signer:3/4=75%)
Cc: "David S. Miller" <davem@davemloft.net> (commit_signer:3/4=75%)
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: arc-linux-dev@synopsys.com
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_tx_timestamp() will clear all zerocopy flags of skb which may lead the
frags never to be orphaned. This will break guest to guest traffic when zerocopy
is enabled. Fix this by orphaning the frags before trying to set tx time stamp.
The issue were introduced by commit eda2977291
(tun: Support software transmit time stamping).
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit eda2977291
(tun: Support software transmit time stamping) will queue skbs into error queue
when tx stamping is enabled. But it forgets to purge the error queue during
detach. This patch fixes this.
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.
qlcnic requests the weight as large as 256 for some of its rings, and
smaller values for other rings. For instance in qlcnic_82xx_napi_add()
I think the intention was to give the tx+rx ring a bigger weight than
to rx-only rings, but it's actually doing the opposite. So I'm assuming
the weights do not really matter much.
Just use the standard NAPI weights for all rings.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this patch capabilities are added to the Vf driver to request
multiple queues over the VF PF channel, and the logic for requesting
rss configuration for said queues.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilong Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Receive Side Scaling for queues of
Virtual Functions on the PF side. This includes support for the
requests for multiple queues from VF drivers, configuration of the
HW for multiple queues per VF, and support for rss configuration
of said queues.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two more ndo ops: ndo_add_rx_vxlan_port() and
ndo_del_rx_vxlan_port().
Drivers can get notifications through the above functions about changes
of the UDP listening port of VXLAN. Also, when physical ports come up,
now they can call vxlan_get_rx_port() in order to obtain the port number(s)
of the existing VXLAN interface in case they already up before them.
This information about the listening UDP port would be used for VXLAN
related offloads.
A big thank you to John Fastabend (john.r.fastabend@intel.com) for his
input and his suggestions on this patch set.
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This module generates a common default address on init,
using eth_random_addr. Set addr_assign_type to let
userspace know the address is random unless it was
overridden by the minidriver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exposes symbols for usnic low latency driver that can be used to
register and unregister vNics as well to traverse the resources on vNics.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In servers with more than 1.1 TB of RAM, the existing 40/32 bit DMA
could cause failure as the DMA-able address could go outside the range
addressable using 40/32 bits.
The following patch first tried 64 bit DMA if possible, failover to 32
bit.
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch sets the skb->rxhash and skb->q_number.
This is used by RPS and RFS. Kernel can make use of hw provided hash
instead of calculating the hash.
Signed-off-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch adds multi tx support for enic.
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Large ocrdma HW driver update: add "fast register" work requests,
fixes, cleanups
- Add receive flow steering support for raw QPs
- Fix IPoIB neighbour race that leads to crash
- iSER updates including support for using "fast register" memory
registration
- IPv6 support for iWARP
- XRC transport fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=rabl
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull main batch of InfiniBand/RDMA changes from Roland Dreier:
- Large ocrdma HW driver update: add "fast register" work requests,
fixes, cleanups
- Add receive flow steering support for raw QPs
- Fix IPoIB neighbour race that leads to crash
- iSER updates including support for using "fast register" memory
registration
- IPv6 support for iWARP
- XRC transport fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (54 commits)
RDMA/ocrdma: Fix compiler warning about int/pointer size mismatch
IB/iser: Fix redundant pointer check in dealloc flow
IB/iser: Fix possible memory leak in iser_create_frwr_pool()
IB/qib: Move COUNTER_MASK definition within qib_mad.h header guards
RDMA/ocrdma: Fix passing wrong opcode to modify_srq
RDMA/ocrdma: Fill PVID in UMC case
RDMA/ocrdma: Add ABI versioning support
RDMA/ocrdma: Consider multiple SGES in case of DPP
RDMA/ocrdma: Fix for displaying proper link speed
RDMA/ocrdma: Increase STAG array size
RDMA/ocrdma: Dont use PD 0 for userpace CQ DB
RDMA/ocrdma: FRMA code cleanup
RDMA/ocrdma: For ERX2 irrespective of Qid, num_posted offset is 24
RDMA/ocrdma: Fix to work with even a single MSI-X vector
RDMA/ocrdma: Remove the MTU check based on Ethernet MTU
RDMA/ocrdma: Add support for fast register work requests (FRWR)
RDMA/ocrdma: Create IRD queue fix
IB/core: Better checking of userspace values for receive flow steering
IB/mlx4: Add receive flow steering support
IB/core: Export ib_create/destroy_flow through uverbs
...
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
While implementing NAPI for the driver, I overlooked the race conditions where
interrupt handler might have called napi_schedule_prep() before napi_enable()
was called or after napi_disable() was called. If RX interrupt happens, this
would cause the endless interrupts and messages like:
sh-eth eth0: ignoring interrupt, status 0x00040000, mask 0x01ff009f.
The interrupt wouldn't even be masked by the kernel eventually since the handler
would return IRQ_HANDLED all the time.
As a fix, move napi_enable() call before request_irq() call and napi_disable()
call after free_irq() call.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan-udp-recv function lookup vxlan_sock struct on every packet
recv by using udp-port number. we can use sk->sk_user_data to
store vxlan_sock and avoid lookup.
I have open coded rcu-api to store and read vxlan_sock from
sk_user_data to avoid sparse warning as sk_user_data is not
__rcu pointer.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The synopsys spec says When TSCRLSSR is cleard, the rollover value of
sub-second register is 0x7FFFFFFF(0.465 ns per clock).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: error to get the previous BD entry. When the current BD
is the first BD, the previous BD entry must be the last BD,
not "bdp - 1" in current logic.
V4:
* Optimize fec_enet_get_nextdesc() for code clean.
Replace "ex_new_bd - ring_size" with "ex_base".
Replace "new_bd - ring_size" with "base".
V3:
* Restore the API name because David suggest to use fec_enet_
prefix for all function in fec driver.
So, change next_bd() -> fec_enet_get_nextdesc()
change pre_bd() -> fec_enet_get_prevdesc()
* Reduce the two APIs parameters for easy to call.
V2:
* Add tx_ring_size and rx_ring_size to struct fec_enet_private.
* Replace api fec_enet_get_nextdesc() with next_bd().
Replace api fec_enet_get_prevdesc() with pre_bd().
* Move all ring size check logic to next_bd() and pre_bd(), which
simplifies the code redundancy.
V1:
* Add BD ring size check to get the previous BD entry in correctly.
Reviewed-by: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <frank.li@freescale.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver supporting NAPI should use NAPI-specific function for receiving packets,
so netif_rx() should be changed to netif_receive_skb().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free_irq is not needed if there has been no request_irq. Free_irq is
removed from both the probe and remove functions. The correct request_irq
and free_irq are found in the open and close functions.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
*e = platform_get_irq(...);
... when != request_irq(e,...)
*free_irq(e,...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
It upsets static analyzers when we don't check for allocation failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates igb driver version to 5.0.5
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the way we report supported/advertised link for i354
devices, especially for 2.5 GB. Instead of reporting 2.5 GB for all i354
devices erroneously, check first, if it is 2.5 GB capable.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes how we get speed/duplex for non_copper devices; it
now uses pcs register to get current speed and duplex instead of using
generic status register that we use to detect speed/duplex for copper
devices.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since i354 2.5Gb devices are not Copper media type but SerDes, so this
patch changes the way we detect speed/duplex link info for this device.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PHY Power Management does not exist for i354 device. So, there is no
need to read and write this register or clear go link Disconnect bit,
which could cause a lot of issues.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements downshift mechanism for M88E1543 PHY, so that
downshift is disabled first during link setup process, and later enabled
if we are master and downshift link is negotiated. Also cleaned up
return code implementation.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes PHY_ID for i354 device, now using M88E1543
instead of M88E1545.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds 1 sec delay mechanism to i210 device family, in order
to avoid erroneous link issue with the link partner.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a part is flashless, do not look for a PBA in the iNVM.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just remove a small semicolon.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes warning "warning: symbol 'qlcnic_set_dcb_ops' was
not declared. Should it be static?"
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"tty->name" and "name" are a 64 character buffers. My static checker
complains because we add the "cf" on the front so it look like we are
copying a 66 character string into a 64 character buffer.
Also if the name is larger than IFNAMSIZ (16) it triggers a BUG_ON()
inside the call to alloc_netdev().
This is all under CAP_SYS_ADMIN so it's not a security fix, it just adds
a little robustness.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hypervisor is big endian, so little endian kernel builds need
to byteswap.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting from 'void *' is unnecessary, because casting from 'void *'
to any pointer type is automatic.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bp->pfid from bnx2x instead to avoid duplication.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BP_PORT and chip_port_mode directly from bnx2x.h to avoid duplication.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This eliminates duplication and ensures that all bnx2x chips will be
supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to harmonize cleanup done on a skbuff on xmit path.
Before this patch, behaviors were different depending of the tunnel type.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is not used, let's remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is not used, let's remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_compute_features is always called with RTNL held, so we can safely
drop the read bond->lock.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're protected by RTNL so nothing can happen and we can safely drop the
read bond->lock.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can drop the use of bond->lock for mutual exclusion in
bond_3ad_update_lacp_rate and use RTNL in the sysfs store function
instead. This way we'll prevent races with mode change and interface
up/down as well as simplify update_lacp_rate by removing the check for
port->slave because it'll always be initialized (done while enslaving
with RTNL). This change will also help in the future removal of reader
bond->lock from bond_enslave.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't have to release all slaves when closing the bond dev, so remove
the outdated comment and the braces around the left single statement.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to remove a use of the bond->lock for mutual exclusion
which will later allow easier migration to RCU of the users of this
functionality. We use RTNL as a synchronizing mechanism since it's
always held when send_peer_notif is set, and when it is decremented from
the notifier function. We can also drop some locking, and fix the
leakage of the send_peer_notif counter.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using pci_dev instead of using dev_{get,set}_drvdata() with
&pdev->dev, so we can directly pass a struct pci_dev. This is
a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using pci_dev instead of using dev_{get,set}_drvdata() with
&pdev->dev, so we can directly pass a struct pci_dev. This is
a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only H8300H_AKI3068NET and H8300H_H8MAX define default
I/O base and IRQ values for the NE_H8300 driver. Hence builds
for other H8300H platforms will fail as per below. Since H8300H
does not support multi platform builds, we simply limit building
the driver to those two platforms specifically.
The release error:
drivers/net/ethernet/8390/ne-h8300.c: In function 'init_dev':
drivers/net/ethernet/8390/ne-h8300.c:117:23: error: 'h8300_ne_base' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c:117:23: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/8390/ne-h8300.c:117:23: error: bit-field '<anonymous>' width not an integer constant
drivers/net/ethernet/8390/ne-h8300.c:119:20: error: 'h8300_ne_irq' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c: In function 'init_module':
drivers/net/ethernet/8390/ne-h8300.c:647:21: error: 'h8300_ne_base' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c:648:15: error: 'h8300_ne_irq' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c:661:4: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script: (and a little typing)
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning off led on port 0 of the 5719 serdes causes all other ports to
lose power and stop functioning. Add tg3_phy_led_bug() function to check
for this condition. We use a switch() in tg3_phy_led_bug() for
consistency with the tg3_phy_power_bug() function.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a DMA mapping error in xgmac_xmit, we should simply free the skb and
return NETDEV_TX_OK rather than -EIO. In the case of errors in mapping
frags, we need to undo everything that has been setup.
Reported-by: Andreas Herrmann <andreas.herrmann@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the mismatch in the DMA mapping and unmapping sizes for receive. The
unmap size must be equal to the map size and should not be the actual
received frame length. The map size should also be adjusted by the
NET_IP_ALIGN size since the h/w buffer size (dma_buf_sz) includes this
offset.
Also, add a missing dma_mapping_error check in xgmac_rx_refill.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_sa_filter_fail and tx_undeflow events are unused and impossible
to occur based on how the h/w is used. We never filter on source MAC
address and TX store and forward mode prevents underflow events.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix xgmac_set_rx_mode to handle several conditions that were not handled
correctly as Lennert Buytenhek describes:
If we have, say, 100 unicast addresses, and 5 multicast addresses, the
unicast address count check will evaluate to true, and set use_hash to
true. The multicast address check will however evaluate to false, and
use_hash won't be set to true again, and XGMAC_FRAME_FILTER_HMC won't
be OR'd into XGMAC_FRAME_FILTER, but since use_hash was still true
from the unicast check, netdev_for_each_mc_addr() will program the
multicast addresses into the hash table instead of using the MAC
address registers, but since the HMC bit wasn't set, the hash table
won't be checked for multicast addresses on receive, and we'll stop
receiving multicast packets entirely.
Also, there is no code that zeroes out MAC address registers reg..31
at the end of this function, meaning that under the right conditions,
unicast/multicast addresses that were previously in the filter but
were then deleted won't be cleared out.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a race condition where the interrupt handler may have called
napi_schedule before napi_enable is called. This would disable interrupts
and never actually schedule napi to run.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the xgmac transmit start and completion work locklessly, it is
possible for xgmac_xmit to stop the tx queue after the xgmac_tx_complete
has run resulting in the tx queue never being woken up. Fix this by
ensuring that ring buffer index updates are visible and recheck the ring
space after stopping the queue. Also fix an off-by-one bug where we need
to stop the queue when the ring buffer space is equal to MAX_SKB_FRAGS.
The implementation used here was copied from
drivers/net/ethernet/broadcom/tg3.c.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that the descriptor writes are visible before the ring buffer head
is updated. Since writel is a barrier, we can simply update the head after
the writel.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX completion code may have freed an skb before the entire sg list
was transmitted. The DMA unmap calls for the fragments could also get
skipped. Now set the skb pointer on every entry in the ring, not just
the head of the sg list. We then use the FS (first segment) bit in the
descriptors to determine skb head vs. fragment.
This also fixes similar bug in xgmac_free_tx_skbufs where clean-up of
a sg list that wraps at the end of the ring buffer would not get
unmapped.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the xgmac_tx_complete to run concurrently with
xgmac_tx_err since there are no locks. Fix this by moving the tx
error handling to a workqueue so we can disable napi while we reset
the transmitter.
Reported-by: Andreas Herrmann <andreas.herrmann@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xgmac_desc_get_buf_len appears to have a copy/paste error. flags is the
wrong field to read. We should be reading buf_size field. cpu_to_le32
should also be le32_to_cpu. This never really mattered as this function
is only used for DMA mapping calls which happen to be nops with coherent
DMA.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgmac does not actually handle frag lists, so this option should not
be set. It does not appear to have had any impact though.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SkyHawk-R can support VEB or VEPA mode.
This patch will allow the user to set/query this switch setting.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the amount of sent bytes reported to BQL by reporting the
number of bytes on wire in the xmit routine, and recording that
value for each skb in order to be correctly confirmed on Tx
confirmation cleanup.
Reporting skb->len to BQL just before exiting xmit is not correct
due to possible insertions of TOE block and alignment bytes in the
skb->data, which are being stripped off by the controller before
transmission on wire. This led to mismatch of (incorrectly)
reported bytes to BQL b/w xmit and Tx confirmation, resulting in
Tx timeout firing, for the h/w tx timestamping acceleration case.
There's no easy way to obtain the number of bytes on wire in the Tx
confirmation routine, so skb->cb is used to convey that information
from xmit to Tx confirmation, for now (as proposed by Eric). Revived
the currently unused GFAR_CB() construct for that purpose.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an oversight when r8a7790 support was added to sh_eth.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store VID in ->vlan_id (if any), and remove the useless ->tag.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're using it currently to verify if we have vlans before getting the tag
from the skb we're about to send. It's useless because the vlan_get_tag()
verifies if the skb has the tag (and returns an error if not), and we can
receive tagged skbs only if we *already* have vlans.
Plus, the current RCUed implementation is kind of useless anyway - the we
can remove the last vlan in the moment we return from the function.
So remove the only usage of it and the whole function.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is a pull request for net-next. There are two patches from Gerhard
Sittig, which improves the clock handling on mpc5121. Oliver Hartkopp
provides a patch that adds a per rule limitation of frame hops.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please accept this batch of updates intended for the 3.12 stream.
For the mac80211 bits, Johannes says this:
"This time I have various improvements all over the place: IBSS, mesh,
testmode, AP client powersave handling, one of the rare rfkill patches
and some code cleanup."
Also for mac80211:
"And I also have some more changes for -next, just a few small fixes and
improvements, nothing really stands out."
And for iwlwifi:
"This time I have some powersave work (notably uAPSD support), CQM
offloads, support for a new firmware API and various code cleanups."
Regarding the Bluetooth bits, Gustavo says:
"Patches to 3.12, here we have:
* implementation of a proper tty_port for RFCOMM devices, this fixes some
issues people were seeing lately in the kernel.
* Add voice_setting option for SCO, it is used for SCO Codec selection
* bugfixes, small improvements and clean ups"
For the NFC bits, Samuel says:
"With this one we have:
- A few pn533 improvements and minor fixes. Testing our pn533 driver
against Google's NCI stack triggered a few issues that we fixed now.
We also added Tx fragmentation support to this driver.
- More NFC secure element handling. We added a GET_SE netlink command
for getting all the discovered secure elements, and we defined 2
additional secure element netlink event (transaction and connectivity).
We also fixed a couple of typos and copy-paste bugs from the secure
element handling code.
- Firmware download support for the pn544 driver. This chipset can enter a
special mode where it's waiting for firmware blobs to replace the
already flashed one. We now support that mode."
With repect to the ath tree, Kalle says:
"New features in ath10k are rx/tx checsumming in hw and survey scan
implemented by Michal. Also he made fixes to different areas of the
driver, most notable being fixing the case when using two streams and
reducing the number of interface combinations to avoid firmware crashes.
Bartosz did a clean related to how we handle SoC power save in PCI
layer.
For ath6kl Mohammed and Vasanth sent each a patch to fix two infrequent
crashes."
I also pulled the wireless tree into wireless-next to support a
request from Johannes. On top of all that, there are the usual
sort of driver updates. The mwifiex, brcmfmac, brcmsmac, ath9k,
and rt2x00 drivers all get some attention, as does the bcma bus and
a few other random bits here and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the VIRTIO_NET_F_GUEST_CSUM virtio feature is available, the guest
does not have to calculate the checksums on all received packets. This
is pretty much the same feature as RX checksum offloading on real
network cards, so the virtio-net driver should report this by setting
the NETIF_F_RXCSUM flag. When the user now runs "ethtool -k", he or she
can see whether the virtio-net interface has to calculate RX checksums
or not.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big tty/serial driver pull request for 3.12-rc1.
Lots of n_tty reworks to resolve some very long-standing issues, removing the
3-4 different locks that were taken for every character. This code has been
beaten on for a long time in linux-next with no reported regressions.
Other than that, a range of serial and tty driver updates and revisions. Full
details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlI6UACgkQMUfUDdst+ym7kgCgmysv/TVeqsdvmkiO2eEB4+xs
ddwAoMqkJ/enCJ2f+fC8y2Wz+5+kDrU7
=CiCp
-----END PGP SIGNATURE-----
Merge tag 'tty-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver pull request for 3.12-rc1.
Lots of n_tty reworks to resolve some very long-standing issues,
removing the 3-4 different locks that were taken for every character.
This code has been beaten on for a long time in linux-next with no
reported regressions.
Other than that, a range of serial and tty driver updates and
revisions. Full details in the shortlog"
* tag 'tty-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (226 commits)
hvc_xen: Remove unnecessary __GFP_ZERO from kzalloc
serial: imx: initialize the local variable
tty: ar933x_uart: add device tree support and binding documentation
tty: ar933x_uart: allow to build the driver as a module
ARM: dts: msm: Update uartdm compatible strings
devicetree: serial: Document msm_serial bindings
serial: unify serial bindings into a single dir
serial: fsl-imx-uart: Cleanup duplicate device tree binding
tty: ar933x_uart: use config_enabled() macro to clean up ifdefs
tty: ar933x_uart: remove superfluous assignment of ar933x_uart_driver.nr
tty: ar933x_uart: use the clk API to get the uart clock
tty: serial: cpm_uart: Adding proper request of GPIO used by cpm_uart driver
serial: sirf: fix the amount of serial ports
serial: sirf: define macro for some magic numbers of USP
serial: icom: move array overflow checks earlier
TTY: amiserial, remove unnecessary platform_set_drvdata()
serial: st-asc: remove unnecessary platform_set_drvdata()
msm_serial: Send more than 1 character on the console w/ UARTDM
msm_serial: Add support for non-GSBI UARTDM devices
msm_serial: Switch clock consumer strings and simplify code
...
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in the
shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlH58ACgkQMUfUDdst+ymTGwCdH1BmMdypyjUBxJEoWNDUuwXn
/AQAoKt329vmB6qn41rvaTilHHYUXS7H
=ovaW
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in
the shortlog"
* tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (62 commits)
drivers: uio: Kconfig: add MMU dependancy for UIO
drivers: uio: Add driver for Humusoft MF624 DAQ PCI card
drivers: uio_pdrv_genirq: use dev_get_platdata()
drivers: uio_pruss: use dev_get_platdata()
drivers: uio_dmem_genirq: use dev_get_platdata()
drivers: parport: Kconfig: exclude h8300 for PARPORT_PC
drivers: misc: ti-st: fix potential race if st_kim_start fails
Drivers: hv: vmbus: Do not attempt to negoatiate a new version prematurely
misc: vmw_balloon: Remove braces to fix build for clang.
Drivers: hv: vmbus: Fix a bug in the handling of channel offers
vme: vme_ca91cx42.c: fix to pass correct device identity to free_irq()
VMCI: Add support for virtual IOMMU
VMCI: Remove non-blocking/pinned queuepair support
uio: uio_pruss: remove unnecessary platform_set_drvdata()
parport: amiga: remove unnecessary platform_set_drvdata()
vme: vme_vmivme7805.c: add missing __iomem annotation
vme: vme_ca91cx42.c: add missing __iomem annotation
vme: vme_tsi148.c: add missing __iomem annotation
drivers/misc/hpilo: Correct panic when an AUX iLO is detected
uio: drop unused vma_count member in uio_device struct
...
Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlJJ8ACgkQMUfUDdst+ymBAwCgg8czTAuwpCCK7H8LHnC2BsMj
dtUAnjDisrbw4qWSXaaA/sfgSZjKW5G4
=Tman
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog"
* tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (352 commits)
usbcore: fix incorrect type in assignment in descriptors_changed()
usbcore: compare and release one bos descriptor in usb_reset_and_verify_device()
ehci: remove debugging statement with ehci statistics in ehci_stop()
ehci: remove duplicate debug_async_open() prototype in ehci-dbg.c
ehci: enable debugging code when CONFIG_DYNAMIC_DEBUG is set
ehci: remove ehci_vdbg() verbose debugging statements
Documentation sysfs-bus-usb: Document which files are used by libusb
Documentation sysfs-bus-usb: Document the speed file used by libusb
Documentation sysfs-bus-usb: Move files with known users to stable
USB: fix build error when CONFIG_PM_SLEEP isn't enabled
usb: r8a66597-hcd: use platform_{get,set}_drvdata()
usb: phy-tegra-usb: use platform_{get,set}_drvdata()
usb: acm gadget: Null termintate strings table
dma: cppi41: off by one in desc_to_chan()
xhci: Fix warning introduced by disabling runtime PM.
dev-core: fix build break when DEBUG is enabled
USB: OHCI: Allow runtime PM without system sleep
usb: ohci-at91: remove unnecessary dev_set_drvdata()
usb: renesas_usbhs: use platform_{get,set}_drvdata()
usb: fotg210-udc: use platform_{get,set}_drvdata()
...
Fengguang reported a compile warning:
drivers/net/vxlan.c: In function 'vxlan6_xmit_skb':
drivers/net/vxlan.c:1352:3: error: implicit declaration of function 'csum_ipv6_magic' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
this patch fixes it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an embedded switch per physical port on the adapter.
Add support for enabling and disabling the embedded switch
on per port basis.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Removed unused and unnecessary members from qlc_83xx_fw_info
structure.
o Made fw_info member of qlcnic_hardware_context as a pointer to
qlc_83xx_fw_info structure.
o Added a member fw_file_name to qlc_83xx_fw_info structure which
will hold the name of firmware image file name.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Generic AER callback handlers will make use of qlcnic_hardware_ops structure
to call adapter specific handlers.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-Use CAMRAM register to store firmware dump state in adapter
instead of maintaining it in each function driver separately.
-Return appropriate error code on failure
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove inline keyword from function prototypes wherever it is not appropriate.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o PF driver should not indicate PVID configuration to VF driver.
As adapter supports VLAN stripping, VF driver should stay agnostic
to any PVID configuration.
o Return "QLC_NO_VLAN_MODE(= 0)" to VFD when PVID is configured.
VF driver should be in no VLAN configuration mode.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the IPv6 version of "arp_reduce", ndisc_send_na()
will be needed.
Cc: David S. Miller <davem@davemloft.net>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
route short circuit only has IPv4 part, this patch adds
the IPv6 part. nd_tbl will be needed.
Cc: David S. Miller <davem@davemloft.net>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPv6 support to vxlan device, as the new version
RFC already mentions it:
http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-03
Cc: David Stevens <dlstevens@us.ibm.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
1. A little more refactoring.
2. Remove the unnecessary use of atomic_t that you pointed out.
3. Add support for starting or queueing firmware requests from atomic
context.
4. Add hwmon support for additional sensors found on some new boards.
5. Add support for the EF10 controller architecture, the SFC9100 family
and specifically the SFC9120 controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dc975382 "net: fec: add napi support to improve proformance"
converted the fec driver to the napi model. However, that commit
forgot to remove the call to skb_defer_rx_timestamp which is only
needed in non-napi drivers.
(The function napi_gro_receive eventually calls netif_receive_skb,
which in turn calls skb_defer_rx_timestamp.)
This patch should also be applied to the 3.9 and 3.10 kernels.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My static checker complains that on some arches unsigned longs can be 8
characters which is larger than the buffer is only 6 chars.
Additionally, Ben Hutchings points out that the buffer actually holds
big endian data and the buffer we are reading from is CPU endian.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 3b04ddde02
"[NET]: Move hardware header operations out of netdevice."
moved the handling into macvlan setup adding
dev->header_ops = &macvlan_hard_header_ops,
At the end of the line the ',' should have been a ';'
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some synopsys ip implementation doesn't support DMA store and forward mode,
such as BF60x. So, set force_thresh_dma_mode to use DMA thresholds only.
Update document and devicetree as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the dates for files that have been added to in 2012-2013.
Drop the 'Solarstorm' brand name that's still lingering here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
the .get_clock() callback is run from probe() and might allocate
resources, introduce a .put_clock() callback that is run from remove()
to undo any allocation activities
prepare and enable the clocks in open(), disable and unprepare the
clocks in close() if clocks were acquired during probe(), to not assume
knowledge about which activities are done in probe() and remove()
use devm_get_clk() to lookup the SYS and REF clocks, to have the clocks
put upon device shutdown
store pointers to data structures upon successful allocation already
instead of deferral until complete setup, such that subroutines in the
setup sequence may access those data structures as well to track their
resource acquisition
since clock allocation remains optional, the release callback as well as
the enable/disable calls in open/close are optional as well
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
add a comment about the magic of deriving an MSCAN component index
from the peripheral's physical address / register offset
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There's no need to call ether_setup() in the driver since prior alloc_etherdev()
call already arranges for it.
Suggested-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They're simply annoying and will spam dmesg constantly if we hit them, so
convert to pr_debug so that we still can access them in case of debugging.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are no real users of vlan_list/current_alb_vlan, only the
helpers which maintain them, so remove them.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if there are vlans on top of bond, alb_send_learning_packets()
will never send LPs from the bond itself (i.e. untagged), which might leave
untagged clients unupdated.
Also, the 'circular vlan' logic (i.e. update only MAX_LP_BURST vlans at a
time, and save the last vlan for the next update) is really suboptimal - in
case of lots of vlans it will take a lot of time to update every vlan. It
is also never called in any hot path and sends only a few small packets -
thus the optimization by itself is useless.
So remove the whole current_alb_vlan/MAX_LP_BURST logic from
alb_send_learning_packets(). Instead, we'll first send a packet untagged
and then traverse the upper dev list, sending a tagged packet for each vlan
found. Also, remove the MAX_LP_BURST define - we already don't need it.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create alb_send_lp_vid(), which will handle the skb/lp creation, vlan
tagging and sending, and use it in alb_send_learning_packets().
This way all the logic remains in alb_send_learning_packets(), which
becomes a lot more cleaner and easier to understand.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always hold the rtnl_lock() in __bond_release_one(), so use
vlan_uses_dev() instead of bond_vlan_used().
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bond_has_this_ip() is aware only of vlan upper devices, and thus
will return false if the address is associated with the upper bridge or any
other device, and thus will break the arp logic.
Fix this by using the upper device list. For every upper device we verify
if the address associated with it is our address, and if yes - return true.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bond_arp_send_all() is aware only of vlans, which breaks
configurations like bond <- bridge (or any other 'upper' device) with IP
(which is quite a common scenario for virt setups).
To fix this we convert the bond_arp_send_all() to first verify if the rt
device is the bond itself, and if not - to go through its list of upper
vlans and their respectiv upper devices (if the vlan's upper device matches
- tag the packet), if still not found - go through all of our upper list
devices to see if any of them match the route device for the target. If the
match is a vlan device - we also save its vlan_id and tag it in
bond_arp_send().
Also, clean the function a bit to be more readable.
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert bond_vlan_used() to traverse the upper device list to see if we
have any vlans above us. It's protected by rcu, and in case we are holding
rtnl_lock we should call vlan_uses_dev() instead - it's faster.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to ixgbe.
Jacob provides a fix for 82599 devices where it can potentially keep link
lights up when the adapter has gone down.
Mark provides a fix to resolve the possible use of uninitialized memory
by checking the return value on EEPROM reads.
Don provides 2 patches, one to fix a issue where we were traversing the
Tx ring with the value of IXGBE_NUM_RX_QUEUES which currently happens
to have the correct value but this is misleading. A change later, could
easily make this no longer correct so when traversing the Tx ring, use
netdev->num_tx_queues. His second patch does some minor clean ups of log
messages.
Emil provides the remaining ixgbe patches. First he fixes the link test
where forcing the laser before the link check can lead to inconsistent
results because it does not guarantee that the link will be negotiated
correctly. Then he initializes the message buffer array to 0 in order
to avoid using random numbers from the memory as a MAC address for the
VF. Emil also fixes the read loop for the I2C data to account for the
offset for SFP+ modules. Lastly, Emil provides several patches to add
support for QSFP modules where 1Gbps support is added as well as support
for older QSFP active direct attach cables which pre-date SFF-8436 v3.6.
v2: Fixed patch 4 description and added blank line based on feedback from
Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a custom 'FEC_NAPI_WEIGHT', just use the generic
'NAPI_POLL_WEIGHT' definition instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace misleading -1 (-EPERM) by a more appropriate return code (-ENXIO)
in macb_mii_probe function.
Save macb_mii_probe return before branching to err_out_unregister to avoid
erronous 0 return.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap_resource instead of of_iomap() and devm_kzalloc()
instead of kmalloc() to make cleanup paths simpler. This patch also
fixes the resource leak caused by missing corresponding iounamp()
of the of_iomap().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the EF10 network controller architecture and the
SFC9100 family, starting with SFC9120 'Farmingdale', and bumps the
driver version to 4.0.
New features in the SFC9100 family include:
- Flexible allocation of internal resources to PCIe physical and virtual
functions under firmware control
- RX event merging to reduce DMA writes at high packet rates
- Integrated RX timestamping
- PIO buffers for lower TX latency
- Firmware-driven data path that supports additional offload features
and filter types
- Delivery of packets between functions and to multiple recipients,
allowing firmware to implement a vswitch
- Multiple RX flow hash (RSS) contexts with their own hash keys and
indirection tables
- 40G MAC (single port only)
...not all of which are enabled in this initial driver or the initial
firmware release.
Much of the new code is by Jon Cooper.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Also update comments and assertions in io.h:
- EF10 does not have a general BIU collector and does not have the
bug affecting TIMER_COMMAND_REG[0] on Falcon/Siena
- The WPTR field moved within RX_DESC_UPD_REG and TX_DESC_UPD_REG.
Adjust efx_writed_page() accordingly
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The TX path firmware for EF10 supports 'option descriptors' to control
offloads and various other features. Add a flag and field for these
in struct efx_tx_buffer, and don't treat them as DMA descriptors on
completion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On EF10, the firmware will initiate a queue flush in certain
error cases. We need to accept that flush events might appear
at any time after a queue has been initialised, not just when
we try to flush them.
We can handle Falcon-architecture in just the same way.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
RX DMA scatter is always enabled on EF10. Adjust the common RX
completion handling to allow for this.
RX completion events on EF10 include the length used from a single
descriptor, not the cumulative length used. Add a field to struct
efx_rx_queue to hold the cumulative length.
[bwh: Also fix a related comment]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add the efx_filter_is_mc_recip() function to decide whether a filter
is for a multicast recipient and can coexist with other filters with
the same match values. Update efx_filter_insert_filter() kernel-doc
to explain the conditions for this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We can set, get and compare-and-exchange without using atomic_t.
Change efx_mcdi_iface::state to the enum type we really wanted it to
be.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add support for power and current sensors, which need to be named
differently in sysfs. Power sensors also require values to be scaled
between MCDI and sysfs, and have no minimum value.
Add definitions of the power, current, fan, and additional temperature
and voltage sensors found on SFA6902F, SFN7022F and SFN7122F.
(Includes a bug fix from Andrew Jackson.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This patch adds support for QSFP active direct attach (DA) cables which
pre-date SFF-8436 v3.6.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that QSFP+ modules use the SFP+ code path for
setting up link.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds GB speed support for QSFP+ modules.
Autonegotiation is not supported with QSFP+. The user will have to set
the desired speed on both link partners using ethtool advertise setting.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the read loop for the I2C data to account for the offset.
Also includes a whitespace cleanup and removes ret_val as it is not needed.
CC: Ben Hutchings <bhutchings@solarflare.com>
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some minor log messages cleanup, changing the level one message is logged,
adding a bit of detail to another and put all the text on one line.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch initializes the msgbuf array to 0 in order to avoid using random
numbers from the memory as MAC address for the VF.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a partial reverse of:
commit dfcc4615f0
Author: Jacob Keller <jacob.e.keller@intel.com>
Date: Thu Nov 8 07:07:08 2012 +0000
ixgbe: ethtool ixgbe_diag_test cleanup
Specifically forcing the laser before the link check can lead to
inconsistent results because it does not guarantee that the link will be
negotiated correctly. Such is the case when dual speed SFP+ module is
connected to a gigabit link partner.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were transversing the tx_ring with IXGBE_NUM_RX_QUEUES. Now this define
happens to have the correct value but this is misleading and a change later
could easily make this no longer true. I updated it to netdev->num_tx_queues
like we use in ixgbe_get_strings().
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the possible use of uninitialized memory by checking the
return value on eeprom reads. These issues were identified by static
analysis. In many cases error messages will be produced so that corrupted
eeprom issues will be more visible.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue with the 82599 adapter where it can potentially keep
link lights up when the adapter has gone down. The patch adds a function which
ensures link is disabled, and calls this function when the adapter transitions
to a down state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ben Hutchings says:
====================
1. Further cleanup and refactoring in preparation for EF10.
2. Remove ethtool stats that are always zero on Falcon boards.
3. Add an ethtool stat for merged TX completions.
4. Prepare to support merged RX completions.
5. Prepare to support more hwmon sensors.
6. Add support for new events that are generated by EF10 firmware.
7. Update MC reboot detection for EF10.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This function checks the upper bound but it doesn't check for negative
numbers:
if (txq > QLCNIC_MAX_TX_RINGS) {
I've solved this by making "txq" a u32 type. I chose that because
->tx_count in the ethtool_channels struct is a __u32.
This bug was added in aa4a1f7df7 ('qlcnic: Enable Tx queue changes using
ethtool for 82xx Series adapter.').
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we move to 1:1 model and melt xen_netbk and xenvif together, it would
be better to use single prefix for all functions in xen-netback.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements 1:1 model netback. NAPI and kthread are utilized
to do the weight-lifting job:
- NAPI is used for guest side TX (host side RX)
- kthread is used for guest side RX (host side TX)
Xenvif and xen_netbk are made into one structure to reduce code size.
This model provides better scheduling fairness among vifs. It is also
prerequisite for implementing multiqueue for Xen netback.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data flow from DomU to DomU on the same host in current copying
scheme with tracking facility:
copy
DomU --------> Dom0 DomU
| ^
|____________________________|
copy
The page in Dom0 is a page with valid MFN. So we can always copy from
page Dom0, thus removing the need for a tracking facility.
copy copy
DomU --------> Dom0 -------> DomU
Simple iperf test shows no performance regression (obviously we copy
twice either way):
W/ tracking: ~5.3Gb/s
W/o tracking: ~5.4Gb/s
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Matt Wilson <msw@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds another entry (HP hs2434 Mobile Broadband) to the list
of exceptional devices that require a zero length packet in order to
function properly. This list was added in commit 844e88f0. The hs2434
is manufactured by Sierra Wireless, who also produces the MC7710,
which the ZLP exception list was created for in the first place. So
hopefully it is just this one producer's devices that will need this
workaround.
Tested on a DM1-4310NR HP notebook, which does not function without this
change.
Signed-off-by: Rob Gardner <robmatic@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej W. Rozycki