The affinity hint is used by the user space daemon, irqbalancer, to
indicate a preferred CPU mask for irqs. This patch sets the irq affinity
hint to local numa core first, when exausted we try non-local numa cores.
Also set tx xps cpus mask bassed on affinity hint.
v2: remove the global affinity policy.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_driver doesn't need to set .owner, because
platform_driver_register() will set it.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a place where checkpatch complains that braces should be used
on all arms of this statement.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes those places where checkpatch complains that comparisons
should place the constant on the right side of the test.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value passed through switchdev attr set is not in jiffies, but in
clock_t, so fix the convert.
Reported-by: Sagi Rotem <sagir@mellanox.com>
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original description was for LAG, so fix it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove a bridged port from the flooding domain of unknown unicast
packets according to user configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling a range of VLANs on a bridged port we can configure
flooding for these VLANs by one register access instead of calling the
same register for each VLAN. This is accomplished by using the 'range'
field of the Switch Flooding Table Register (SFTR).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a flag anyway, so move it to existing u8 flag and don't waste mem.
Fix the flags to be in single u8 on the way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RGMII TX/RX delay configuration support. RGMII standard requires 2ns
delay to help the RGMII bridge receiver to sample data correctly. If the
default value does not provide proper centering of the data sample, the
TX/RX delay parameters can be used to adjust accordingly.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing memcpy/memset of EQEs, we should use sizeof struct
mlx4_eqe as the base size and not caps.eqe_size which could be bigger.
If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt
data in the master context.
When using a 64 byte stride, the memcpy copied over 63 bytes to the
slave_eq structure. This resulted in copying over the entire eqe of
interest, including its ownership bit -- and also 31 bytes of garbage
into the next WQE in the slave EQ -- which did NOT include the ownership
bit (and therefore had no impact).
However, once the stride is increased to 128, we are overwriting the
ownership bits of *three* eqes in the slave_eq struct. This results
in an incorrect ownership bit for those eqes, which causes the eq to
seem to be full. The issue therefore surfaced only once 128-byte EQEs
started being used in SRIOV and (overarchitectures that have 128/256
byte cache-lines such as PPC) - e.g after commit 77507aa249
"net/mlx4_core: Enable CQE/EQE stride support".
Fixes: 08ff32352d ('mlx4: 64-byte CQE/EQE support')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not set the ins_vlan field to zero when no vlan id is present in the packet.
Since WQEs in the TX ring are not zeroed out between uses, this oversight
could result in having vlan flags present in the WQE ctrl segment when no
vlan is preset.
Fixes: e38af4faf0 ('net/mlx4_en: Add support for hardware accelerated 802.1ad vlan')
Reported-by: Gideon Naim <gideonn@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
delete action of ETHTOOL_ID_ON/ETHTOOL_ID_OFF in XGE ethtool -p,
so Hardware control the LED state instead of software.
Signed-off-by: Li Peng <lipeng321@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased TX_TIMEOUT to 5HZ to accommodate worst case situation
for traffic and CPU intensive use cases
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Abhimanyu <abhimanyu@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During Tx cleanup it's still possible for the descriptor data to be
read ahead of the descriptor index. A memory barrier is required between
the read of the descriptor index and the start of the Tx cleanup loop.
This allows a change to a lighter-weight barrier in the Tx transmit
routine just before updating the current descriptor index.
Since the memory barrier does result in extra overhead on arm64, keep
the previous change to not chase the current descriptor value. This
prevents the execution of the barrier for each loop performed.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcedeth currently uses disable_irq_lockdep and enable_irq_lockdep, which in
some configurations simply calls local_irq_disable. This causes errant warnings
in the netpoll path as in netpoll_send_skb_on_dev, where we disable irqs using
local_irq_save, leading to the following warning:
WARNING: at net/core/netpoll.c:352 netpoll_send_skb_on_dev+0x243/0x250() (Not
tainted)
Hardware name:
netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll
(nv_start_xmit_optimized+0x0/0x860 [forcedeth])
Modules linked in: netconsole(+) configfs ipv6 iptable_filter ip_tables ppdev
parport_pc parport sg microcode serio_raw edac_core edac_mce_amd k8temp
snd_hda_codec_realtek snd_hda_codec_generic forcedeth snd_hda_intel
snd_hda_codec snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd soundcore
snd_page_alloc i2c_nforce2 i2c_core shpchp ext4 jbd2 mbcache sr_mod cdrom sd_mod
crc_t10dif pata_amd ata_generic pata_acpi sata_nv dm_mirror dm_region_hash
dm_log dm_mod [last unloaded: scsi_wait_scan]
Pid: 1940, comm: modprobe Not tainted 2.6.32-573.7.1.el6.x86_64.debug #1
Call Trace:
[<ffffffff8107bbc1>] ? warn_slowpath_common+0x91/0xe0
[<ffffffff8107bcc6>] ? warn_slowpath_fmt+0x46/0x60
[<ffffffffa00fe5b0>] ? nv_start_xmit_optimized+0x0/0x860 [forcedeth]
[<ffffffff814b3593>] ? netpoll_send_skb_on_dev+0x243/0x250
[<ffffffff814b37c9>] ? netpoll_send_udp+0x229/0x270
[<ffffffffa02e3299>] ? write_msg+0x39/0x110 [netconsole]
[<ffffffffa02e331b>] ? write_msg+0xbb/0x110 [netconsole]
[<ffffffff8107bd55>] ? __call_console_drivers+0x75/0x90
[<ffffffff8107bdba>] ? _call_console_drivers+0x4a/0x80
[<ffffffff8107c445>] ? release_console_sem+0xe5/0x250
[<ffffffff8107d200>] ? register_console+0x190/0x3e0
[<ffffffffa02e71a6>] ? init_netconsole+0x1a6/0x216 [netconsole]
[<ffffffffa02e7000>] ? init_netconsole+0x0/0x216 [netconsole]
[<ffffffff810020d0>] ? do_one_initcall+0xc0/0x280
[<ffffffff810d4933>] ? sys_init_module+0xe3/0x260
[<ffffffff8100b0d2>] ? system_call_fastpath+0x16/0x1b
---[ end trace f349c7af88e6a6d5 ]---
console [netcon0] enabled
netconsole: network logging started
Fix it by modifying the forcedeth code to use
disable_irq_nosync_lockdep_irqsavedisable_irq_nosync_lockdep_irqsave instead,
which saves and restores irq state properly. This also saves us a little code
in the process
Tested by the reporter, with successful restuls
Patch applies to the head of the net tree
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the overhead of locking for busy poll.
Previously the state was protected by a lock, whereas now
it's manipulated solely with atomic operations.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_available_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer size calulation failed to account for the length granularity
(which is now 32 bytes)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both Renesas R-Car and RZ/A1 manuals state that RX buffer length must be
a multiple of 32 bytes, while the driver only uses 16 byte granularity...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_gro_skb() has unused variables when CONFIG_INET is not set. We
really cannot support hardware GRO if CONFIG_INET is not set, so
compile out bnxt_gro_skb() completely and define BNXT_FLAG_GRO to be 0
if CONFIG_INET is not set. This will effectively always disable
hardware GRO if CONFIG_INET is not set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx BSY error interrupt indicates that a frame was
received and discarded due to lack of buffers, so it's
a rx ring overflow condition and has nothing to do with
with bad rx packets. Use the right counter.
BSY conditions happen when the SoC is under performance
stress. Doing *more* work in stress situations by trying
to schedule NAPI is not a good idea as the stressed system
becomes still more stressed. The Rx interrupt is already
at work making sure the NAPI is scheduled.
So calling gfar_receive() here does not help. This issue
was present since day 1.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under one unusual circumstance it's possible to wrongly set
FILREN without enabling PRSDEP as well in the RCTRL register,
against the hardware specifications. With the default config
this does not happen because the default Rx offloads (Rx csum
and Rx VLAN) properly enable PRSDEP. But if anyone disables
all these offloads (via ethtool), we get a wrong configuration
were the Rx flow classification and hashing, and other Filer
based features (e.g. wake-on-filer interrupt) won't work.
This patch fixes the issue.
Also, account for Rx FCB insertion which happens every time
PRSDEP is set.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RQFCR_AND is duplicated.
Add missing space as well.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the mask used to update the LED configuration so that it clears
the necessary bits as well as setting the bits according to the mask.
Also reverse the LED configuration to show the Link state + collisions in
LEDA and the Link state + TX/RX events in LEDB.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing function to clear the MIB statatistics was using the
wrong address for the registers. Also, the counters would of been
cleared when the interface was brought up, not during the
probe. Fix both of these.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool statistic interface, returning the full set
of statistics which both Armada 370, 38x and Armada XP can support.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ThunderX pass2 CPI and MPI configuration changes.
MPI_ALG is not enabled i.e MCAM parsing is disabled.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test for pass-1 silicon was incorrect, it should be for all
revisions less than 8. Also the revision is already present in the
pci_dev, so there is no need to read and keep a private copy.
Remove rev_id and code to read it from struct nicpf. Create new
static inline function pass1_silicon() to be used to testing the
silicon version. Use pass1_silicon() for revision checks, this will
be more widely used in follow on patches.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some silicon revisions, the soft reset clobbers PCI config space,
so quit doing the reset.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
struct bnxt_pf_info needs to be always defined. Move bnxt_update_vf_mac()
to bnxt_sriov.c and add some missing #ifdef CONFIG_BNXT_SRIOV.
Reported-by: Jim Hull <jim.hull@hpe.com>
Tested-by: Jim Hull <jim.hull@hpe.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-23
This series contains updates to i40e, i40evf, if_link, ixgbe and ixgbevf.
Anjali adds a workaround to drop any flow control frames from being
transmitted from any VSI, so that a malicious VF cannot send flow control
or PFC packets out on the wire. Also fixed a bug in debugfs by grabbing
the filter list lock before adding or deleting a filter.
Akeem fixes an issue where we were unconditionally returning VEB bridge
mode before allowing LB in the add VSI routine, resolve by checking if
the bridge is actually in VEB mode first.
Mitch fixed an issue where the incorrect structure was being used for
VLAN filter list, which meant the VLAN filter list did not get
processed correctly and VLAN filters would not be re-enabled after any
kind of reset.
Helin fixed a problem of possibly getting inconsistent flow control
status after a PF reset. The issue was requested_mode was being set
with a default value during probe, but the hardware state could be a
different value from this mode.
Carolyn fixed a problem where the driver output of the OEM version
string varied from the other tools.
Jean Sacren fixes up kernel documentation by fixing function header
comments to match actual variables used in the functions. Also
cleaned up variable initialization, when the variable would be
over-written immediately.
Hiroshi Shimanoto provides three patches to add "trusted" VF by adding
netlink directives and an NDO entry. Then implement these new controls
in ixgbe and ixgbevf. This series has gone through several iterations
to address all the suggested community changes and concerns.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan