The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd screen,
microsd slot, headphones, mini hdmi, mini usb b and power barrel connectors.
It uses a rtl8188cus usb wifi chip and a RDA 5875Y bluetooth chip attached
to uart2. It has a bma250 accelerometer attached to i2c1 addr 0x18, this
only works when ldo3 is set to 2.8 volt, otherwise i2c1 gets stuck, so
for now we mark i2c1 as failed.
It has a pixcir,pixcir_tangoc compatible touchscreen attached to i2c2 addr
0x5c. This is not enabled in this dts, because this variant of the
pixcir_tangoc has separate wakeup and enable pins both of which need
to be driven low before the touchscreen will work. Before we can enable
this the pixcir driver and devicetree-bindings need to be extended to
support these pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Based on i.MX6 Quad with 4GB of DDR3.
http://boundarydevices.com/product/nitrogen6max/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With omap5-board-common.dtsi, we can now easily add support for various omap5
board variants. Let's add minimal support for isee igepv5.
So far I've tested that basic things work, such as serial, USB Ethernet, HDMI
and WLAN.
Note that like omap5-uevm, these boards seem to need to reserve 16MB for a
trap section as in commit 03178c66d2 ("ARM: dts: omap5-evm: Update
available memory to 2032 MB") and also noted in a u-boot commit at
http://marc.info/?l=u-boot&m=134376852603255 and also at
http://patchwork.ozlabs.org/patch/159881/.
Not sure why this is not needed for omap5-cm-t54.dts, maybe because of
different u-boot configuration.
Signed-off-by: Tony Lindgren <tony@atomide.com>
- DCAN sleep pins for am437x-gp-evm
- A series of changes to add audio support for dra7
- Add support for gpio keys and LEDs on dra7
- Regulator clean-up for am335x-wega
- A series of changes to enable IOMMUs and mailboxes for dra7
accelerators
- Add support for am335x-bonegreen
- Fix up GPIO flags where 0 was used instead of GPIO_ACTIVE_HIGH
- Fix omap3-lilly-am33x IRQ level flag
- Remove duplicate uart2 pinmux for igep and fix indentation and
update igep to use pinctrl macros for the register offsets
- Fix MMC cd-gpios usage
Note that this branch is against v4.3-rc4 as that contains critical
MMC related fixes to boot with MMC working on most omaps.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Sbup
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree changes for omaps for v4.4 merge window:" from Tony Lindgren:
- DCAN sleep pins for am437x-gp-evm
- A series of changes to add audio support for dra7
- Add support for gpio keys and LEDs on dra7
- Regulator clean-up for am335x-wega
- A series of changes to enable IOMMUs and mailboxes for dra7
accelerators
- Add support for am335x-bonegreen
- Fix up GPIO flags where 0 was used instead of GPIO_ACTIVE_HIGH
- Fix omap3-lilly-am33x IRQ level flag
- Remove duplicate uart2 pinmux for igep and fix indentation and
update igep to use pinctrl macros for the register offsets
- Fix MMC cd-gpios usage
Note that this branch is against v4.3-rc4 as that contains critical
MMC related fixes to boot with MMC working on most omaps.
* tag 'omap-for-v4.4/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (33 commits)
ARM: dts: omap3-igep: Use OMAP3_CORE1_IOPAD pinmux macro
ARM: dts: dra7xx: am57xx: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: am43xx: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: am335x: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: omap3-igep0020: Remove duplicate uart2 pinmux
ARM: dts: omap3-igep: Fix indentation
ARM: dts: omap3-lilly-a83x: Don't use IRQ level flag for a GPIO
ARM: dts: DRA74x: Add IOMMU nodes for DSP2
ARM: dts: DRA7: Add common IOMMU nodes
ARM: dts: DRA74x: Add dsp2_system syscon node
ARM: dts: DRA7: Add dsp1_system syscon node
ARM: dts: Use defined GPIO constants in flags cell for OMAP2+ boards
ARM: dts: Add am335x-bonegreen
ARM: dts: beagle-x15: Enable the system mailboxes 5 and 6
ARM: dts: dra72-evm: Enable the system mailboxes 5 and 6
ARM: dts: dra7-evm: Enable the system mailboxes 5 and 6
ARM: dts: DRA72x: Add IPC sub-mailbox nodes for IPU1, IPU2 & DSP1
ARM: dts: DRA74x: Add IPC sub-mailbox nodes for all IPUs & DSPs
ARM: dts: am335x-wega: Clean up regulators
ARM: dts: dra7-evm: add gpio key support
...
- New board support
: add exynos5250-snow-rev5 DT file to support Snow Rev5+ board
: add exynos5422-odroidxu4 DT file to support Odroid XU4 board
: split exynos5422-odroidxu3-audio DT file from odroidxu3-common
- USE GPIO constants for flags cells for exynos boards
- fix cpu compatible value to 'arm926ej-s' for s3c2416
- add DMA support for serial ports for exynos4
- add suspend opp for exynos4412
- remove regulator-compatible usage for exynos4412-trats2
- enable EC vboot context support for Peach boards
- move display-timings node to DP for exynos5250-arndale, smdk5250 and smdk5420
- for exynos4412-odroid/odroidu3
: unify voltage regulator style and
: remove redundant pinctrl settings
: add pwm-fan node and use it as a colling device
- for exynos5422-odroidxu3
: fix power off method and LEDs
- dt-bindings
: grounded AC0KB pin on S2MPS11
: entry how to use PWM FAN as a cooling device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FqOp
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v4.4" from Kukjin Kim:
- New board support
: add exynos5250-snow-rev5 DT file to support Snow Rev5+ board
: add exynos5422-odroidxu4 DT file to support Odroid XU4 board
: split exynos5422-odroidxu3-audio DT file from odroidxu3-common
- USE GPIO constants for flags cells for exynos boards
- fix cpu compatible value to 'arm926ej-s' for s3c2416
- add DMA support for serial ports for exynos4
- add suspend opp for exynos4412
- remove regulator-compatible usage for exynos4412-trats2
- enable EC vboot context support for Peach boards
- move display-timings node to DP for exynos5250-arndale, smdk5250 and smdk5420
- for exynos4412-odroid/odroidu3
: unify voltage regulator style and
: remove redundant pinctrl settings
: add pwm-fan node and use it as a colling device
- for exynos5422-odroidxu3
: fix power off method and LEDs
- dt-bindings
: grounded AC0KB pin on S2MPS11
: entry how to use PWM FAN as a cooling device
* tag 'samsung-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (22 commits)
ARM: dts: Use GPIO constants for flags cells in exynos5440 boards
ARM: dts: Use GPIO constants for flags cells in exynos5420/5422/5800 boards
ARM: dts: Use GPIO constants for flags cells in exynos4412 boards
ARM: dts: Use GPIO constants for flags cells in exynos4120 boards
ARM: dts: Use GPIO constants for flags cells in exynos3250 boards
ARM: dts: Enable EC vboot context support on Peach boards
ARM: dts: Remove regulator-compatible usage in exynos4412-trats2
ARM: dts: Move display-timings node from fimd to dp in exynos5250-arndale, smdk5250 and smdk5420
ARM: dts: Add Exynos5250 Snow Rev5+ support on exynos5250-snow-rev5
ARM: dts: Unify voltage regulator style in exynos4412-odroid
ARM: dts: Remove redundant pinctrl settings in exynos4412-odroid
ARM: dts: Fix cpu compatible value for s3c2416
ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4
ARM: dts: Split audio configuration to separate exynos5422-odroidxu3-audio
ARM: dts: Fix power off method for exynos5422-odroidxu3-common
dt-bindings: Document grounded ACOKB pin on S2MPS11
ARM: dts: use pwm-fan device as a cooling device for exynos4412-odroidu3
ARM: dts: Add pwm-fan node for exynos4412-odroidu3
dt-bindings: Documentation entry to explain how to use PWM FAN as a cooling device
ARM: dts: add suspend opp to exynos4412
...
DT patches for the 4.4 merge window, most notably:
- Enable the OTG controller on more boards
- Create new DTSI for the q8's design
- Added RSB support to the A23 and A33 SoCs
- New boards: Olimex A20 EVB, Yones bs1078v2
Plus the usual random patches enabling and / or enhancing a few things in
particular boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q2Q4
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT changes for 4.4" from Maxime Ripard:
DT patches for the 4.4 merge window, most notably:
- Enable the OTG controller on more boards
- Create new DTSI for the q8's design
- Added RSB support to the A23 and A33 SoCs
- New boards: Olimex A20 EVB, Yones bs1078v2
Plus the usual random patches enabling and / or enhancing a few things in
particular boards.
* tag 'sunxi-dt-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (59 commits)
ARM: dts: sun6i: hummingbird: Drop AXP221 DC1SW and DC5LDO supplies
ARM: dts: sun8i: sinlinx-sina33: Enable Reduced Serial Bus controller
ARM: dts: sun8i: q8-common: Enable RSB controller for A23/A33 Q8 tablets
ARM: dts: sun8i: Add Reduced Serial Bus controller device node to A23/A33 dtsi
ARM: dts: sun4i: Add AXP209 PMU regulators for pcDuino1/2
ARM: sun7i: dt: Add new Olimex A20 EVB device
ARM: dts: sun6i: hummingbird: Add aliases for rtc devices
ARM: dts: sun7i: Add dts file for Wits Pro A20 DKT
ARM: dts: sun7i: Enable USB DRC on Wexler TAB7200
ARM: dts: sun7i: Enable USB DRC on the Orange pi
ARM: dts: sun7i: Enable USB DRC on orangepi-mini
ARM: dts: axp209: Add usb_power_supply child node to the ax209 node
ARM: dts: sun8i: Make ippo-q8h-v1.2.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Add sun8i-a33-q8-tablet.dts file
ARM: dts: sun6i: Add support for Yones Toptech bs1078v2 tablets
ARM: dts: sun4i: Enable USB DRC on the Marsboard A10
ARM: dts: sun4i: gemei-g9: Add accelerometer (bma250) IRQ
ARM: dts: sun8i-a33: Add security system crypto engine clock and device nodes
ARM: dts: sun8i: Add pwm-backlight device for A23/A33 Q8 format tablets
ARM: sun8i: A23: Add missing msgbox gate
...
This is a generic dts file for A23 based q8 formfactor tablets,
this is intended to replace both sun8i-a23-ippo-q8h-v5.dts and
sun8i-a23-ippo-q8h-v1.2.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).
This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]
http://beagleboard.org/greenhttp://www.seeedstudio.com/wiki/Beaglebone_green
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds DT support for the Seagate Personal Cloud 1 and 2-Bay.
Here are some information allowing to identify these devices:
Product name | Personal Cloud | Personal Cloud 2-Bay
Code name (board/PCB) | Cumulus | Cumulus Max
Model name (case sticker) | SRN21C | SRN22C
Material desc (product spec) | STCRxxxxxxx | STCSxxxxxxx
Chipset list:
- SoC Marvell Armada 370 88F6707, CPU @1GHz
- SDRAM memory: 512MB DDR3 667MHz (16-bits bandwidth)
- SPI flash 1MB (Macronix MX25L8006E)
- 1 or 2 SATA internal ports
- 1 Ethernet Gigabit port (PHY Marvell 88E1518)
- 1 USB3 host port (PCIe controller ASM1042)
- 1 USB2 host port (SoC)
- 2 push buttons (power and reset)
- 1 SATA LED (bi-color, white and red)
Note that support for the white SATA LED is missing. A dedicated LED
driver is needed.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds DT support for the Seagate NAS 2 and 4-Bay.
Here are some information allowing to identify these devices:
Product name | Seagate NAS 2-Bay | Seagate NAS 4-Bay
Code name (board/PCB) | Dart 2-Bay | Dart 4-Bay
Model name (case sticker) | SRPD20 | SRPD40
Material desc (product spec) | STCTxxxxxxx | STCUxxxxxxx
Chipset list (common):
- SoC Marvell Armada 370 88F6707, CPU @1.2GHz
- SDRAM memory: 512MB DDR3 600MHz (16-bits bandwidth)
- NAND flash 256MB, 8-bits (Micron MT29F2G08AAB or Hinyx H27U2G8F2CTR-BC)
- 2 SATA II ports (SoC)
- 1 Ethernet Gigabit ports (PHY Marvell 88E1518)
- 2 USB3 host ports (PCIe controller ASM1042)
- GPIO fan (4 speeds)
- External I2C RTC (MCP7940NT)
- 3 push buttons (power, backup and reset)
- 2 SATA LEDs (bi-color, blue and red)
- 1 power LED (bi-color, blue and red)
Only on 4-Bay models:
- 2 extra SATA III ports (PCIe AHCI controller Marvell 88SE9170)
- 1 extra Ethernet Gigabit ports (PHY Marvell 88E1518)
- I2C GPIO expander (PCA9554A)
- 2 extra SATA LEDs (bi-color, blue and red)
Note that support for the white SATA LEDs associated with HDDs 0 and 1
is missing. A dedicated LED driver is needed.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The LinkSprite pcDuino2 board is almost identical to the older
LinkSprite pcDuino1 board according to the schematic pdf files.
So we just include the existing "sun4i-a10-pcduino.dts" file and
make the necessary adjustments.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Merge "Broadcom devicetree changes for v4.4" from Florian Fainelli:
This pull requests contains the following Broadcom SoCs Device Tree changes:
- Brian Norris documents the BCM7445 SoCs Power Management controllers and
hardware and updates the reference BCM7445 Device Tree with these nodes
- Florian Fainelli documents the BCM7xxx write-pairing feature in the top-level
BCM7xxx binding document
- Hauke Merthens enables the NAND controller for the Asus RT-AC87U and adds the
GPIO pin controlling the USB power supply on Netgear R6250
- Jon Mason adds support for the NorthStar Plus SoC by providing a top-level
binding document and the minimalist device tree skeleton for these SoCs
- Rafal Milecki adds support for the Netgear R7000 (BCM5301x SoC)
- Ray Jui provides a set of Cygnus DT changes that make the Device Tree clearer
and more correct with respect to how the hardware is designed. He also enables
the NAND controller on the bcm911360_entphn design, enables a bunch of
peripherals on the bcm958305k evaluation board, and adds a skeleton .dtsi file
for the touchscreen extansion board(s)
* tag 'arm-soc/for-4.4/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: move aliases back to .dts in Cygnus
ARM: dts: fix Cygnus nand device node
ARM: dts: enable touchscreen support on Cygnus
ARM: dts: Enable NAND support on bcm911360_entphn
ARM: dts: Enable various peripherals on bcm958305k
ARM: dts: Reorder Cygnus peripherals
ARM: dts: Move all Cygnus peripherals into axi bus
ARM: dts: Put Cygnus core components under core bus
ARM: dts: Use label for device nodes in Cygnus dts
ARM: dts: consolidate aliases for Cygnus dt files
ARM: BCM5301X: Netgear R6250 add USB GPIO
Documentation: bindings: brcmstb: Document write-pairing
ARM: dts: brcmstb: add BCM7445 system PM DT nodes
Documentation: dt: brcmstb: add system PM bindings
ARM: BCM5301X: add NAND flash chip description for Asus RT-AC87U
ARM: BCM5301X: Add DT for Netgear R7000
ARM: NSP: add minimal Northstar Plus device tree
dt-bindings: Create Documentation for NSP DT bindings
system-on-module as well as the square baseboard. On top of that
a lot of mmc-related changes to improve speeds on the Cortex-A9
socs and also setting up the supplies for rk3288 mmc-controllers
for the following mmc-tuning support. And of course the dts-part
of the rk3288 power-domains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWFta1AAoJEPOmecmc0R2BwsoH/iAhuYW/AMw9theS5e3QKYaT
AetDQHjjXPkbQpkMMxVpyyIGhBvHWHX+iTINqkVVx5MVlhvC1xmF4oJ6Yo4lbDVF
S6YgYrgI72P4inP0v3DZhJ2CpYB7bTVcPsU/ZiJOacvwKk2rgXWqE+nbBrZHpYbe
pDR9ONdOB0PsXfTsawcjb1FmK2/+xwRhHZJUSdlQRIoUZe1qIOjR2Lx25sprQ6vb
v6sBuY2T/rrWlKE0ME6HtdcA2s7HLKY1E1OdQPr15ceXR8k0yRz0dqH0ydULtZVZ
d6ZghxS+1ygir6Uw4sUXQa5QZjEeWU7M9+z6jCdKLEH/jUuaTFKFj+tko9uboa8=
=LB4D
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Rockchip dts32 changes for 4.4" from Heiko Stuebner:
DTS changes including one new Veyron-board and the Radxa Rock2
system-on-module as well as the square baseboard. On top of that
a lot of mmc-related changes to improve speeds on the Cortex-A9
socs and also setting up the supplies for rk3288 mmc-controllers
for the following mmc-tuning support. And of course the dts-part
of the rk3288 power-domains.
* tag 'v4.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the support power-domain node on RK3288 SoCs
ARM: dts: rockchip: add rk3288-firefly iodomains
ARM: dts: rockchip: fixup firefly mmc supplies
ARM: dts: rockchip: add rk3288-popmetal iodomains
ARM: dts: rockchip: add rk3288-popmetal mmc supplies
ARM: dts: rockchip: add rk3288-popmetal board to dtb list
ARM: dts: rockchip: Add dtb for the Radxa Rock 2 Square board
ARM: dts: rockchip: support highspeed sd-cards on rk3066a boards
ARM: dts: rockchip: support highspeed sd-cards for rk3188-radxarock
ARM: dts: rockchip: Add the hdmi-ddc pinctrl settings for rk3288
ARM: dts: rockchip: Remove specific cts pullup from veyron
ARM: dts: rockchip: pull up cts lines on rk3288
ARM: dts: rockchip: add veyron-jaq board
ARM: dts: rockchip: Add support for SD/MMC on MarsBoard-RK3066
dt-bindings: add power-domain header for RK3288 SoCs
The popmetal board was not included in the list of Rockchip boards,
so was only built when explicitly called with make rk3288-popmetal.dtb
but not in a generic make dtbs, so add the missing entry.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa Rock 2 Square board is a combination of the Radxa Rock 2 SoM
with the Square baseboard. Add a dtsi for the SoM which can be included
into the dts for the various baseboards (e.g. full and square) and a dts
for the square board.
Currently supported are serial console, wired networking, hdmi output,
eMMC and SD storage and USB.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
a.k.a. Haier Chromebook 11, and others
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the initial device tree for the R8A7791 SoC based Porter low cost board
(which is a slightly modified version of the Henninger board).
SCIF0 serial port support is included, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The A20-SOM-EVB is a reference design of a 2-layer board for the
A20-SOM.
It expands the features of A20-SOM by adding VGA connector, HDMI
connector, audio In/Out, LCD connector, 2 Mpix camera, gigabit
Ethernet, SATA, USB-OTG and 2 USB hosts.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There are 2 revisions of the Exynos5250 Snow Chromebook that were
shipped: Rev4 and Rev5. The only difference between these 2 revisions
is the codec, Rev4 has a max98095 codec while Rev5 has a max98090.
Mainline only supports Rev4 so this patch moves the common device
nodes to a DTSI file and adds a DTS for the Exynos5250 Snow Rev5.
The Snow Rev5 DTS is based on the DTS found in the ChromiumOS 3.8
tree.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND,
sdio wifi, 1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen
and a ton of IO connectors.
Note there seem to be multiple sdcard slots on the board (4 in total), but
other then mmc0 none of these are hooked up by default, there is a ton of
dip-switches which likely allow hooking some of these up, but the
documentation of the board only describes the use of a fraction of them,
so for now we only support mmc0.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
[hdegoede@redhat.com: Use pwrseq instead of a regulator for the wifi-en pin]
[hdegoede@redhat.com: Add support for OOB irq for the sdio wifi]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a generic dts file for A33 based q8 formfactor tablets,
this is intended to replace both sun8i-a33-ippo-q8h-v1.2.dts and
sun8i-a33-et-q8-v1.6.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The bs1078v2 is a pcb found in 10.1" tablets with an A31 soc, 1G RAM
and 8G NAND, rtl8723as usb wifi, 1 micro USB OTG port, 1 USB HOST port
This commit adds a dts for v2 of the bs1078 pcb.
Signed-off-by: Lawrence Yu <lyu@micile.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commits adds a generic dts file for q8 formfactor a13 based tablets.
The tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.
The wifi is USB based, and thus not listed in devicetree.
The touchscreen controller / accelerometer may turn out to be a problem
once we add support for those. We can either do something with devicetree
overlays, or add sun5i-a13-<touchscreen>-<accelerometer>.dts files. The
latter is what the android mod community is doing with firmware images.
This dts was tested with an a13 q8 tablet with a pcb labelled: "94V-0",
silead gsl1680 touchscreen controller and a mc32x0 accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.
This commit adds a dts file adding support for this top set box.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The iNet-tek iNet-1 PCB is a PCB found in various generic 10.1" 1024x600
A10 based tablets such as the Point of View Protab2 XXL and the
Cherry M1007.
This patch has been tested on both rev2 and rev5 of this board / these
tablets.
It comes with a rtl8188cus usb wifi connected to ehci1, focal ft5406ee8
touchscreen connected to i2c2 addr 0x38, bosch bma 250 accelerometer
connected to i2c1 addr 0x18 and the usual connectors: headphone,
mini hdmi, power-barrel, mini-usb and a micro-sd slot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The inet9f-rev03 pcb is specially designed for gaming tablets, such as
the qware tb-g100 tablet.
These 7" tablets feature a dpad, firebuttons and 2 joysticks on the sides
of the screen.
Besides this they have the usual connectors: power-barrel, mini usb,
mini hdmi, headphone and micro-sd slot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The inet98v_rev2 is a pcb used in generic A13 based tablets. It features
volume buttons, a power barrel, micro-usb otg, headphone connector and
a power button.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Auxtek-T003 HDMI stick is an A10s based HDMI stick with USB wifi,
and composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM
and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot.
This commit adds a dts for v4 of the gt90h pcb.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add Hardkernel Odroid XU4 board Device Tree sources. The board differs
from Odroid XU3 and XU3-Lite by:
1. No green and red LEDs (except standard red power LED).
2. Only two PWM outputs are used (fan and blue LED)
3. No audio codec.
4. Two USB3 ports in host mode (no micro USB3 connector for OTG).
5. Realtek RTL8153-CG gigabit network adapter (instead of SMSC9514).
6. Additional connector with IO ports (I2S_0, I2C_5).
7. No DisplayPort (like XU3-Lite).
8. No TI INA231 power measurement sensors (like XU3-Lite).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add a very minimalistic set of Northstar Plus Device Tree files which
describes the SoC and the BCM958625 implementation. The perpherials
described are:
ARM Cortex A9 CPU
2 8250 UARTs
ARM GIC
PL310 L2 Cache
ARM A9 Global timer
Signed-off-by: Kapil Hali <kapilh@broadcom.com>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Commit 79ae3e66f8 (ARM: dts: sun4i: Add Iteaduino Plus A10) added a new
make target for the sun4i-a10-itead-iteaduino-plus dts file, but mistakenly
used .dts instead of the correct .dtb suffix. This resulted in a build error
like:
scripts/Makefile.dtbinst:42: target 'sun4i-a10-itead-iteaduino-plus.dts' doesn't match the target pattern
when doing a make dtbs_install.
Fix it to use the proper file name.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
- Add audio and eTSEC device support and update dspi node for LS1021A.
- Add initial i.MX6UL and imx6ul-14x14-evk board support, and enable
a bunch of device support for i.MX6UL, including RTC, power key, USB,
QSPI, and dual FEC.
- Enable HDMI and LVDS dual display support for a few imx6qdl boards.
- Support of imx6sl-warp board rev1.12, the version which will be
publicly available for the customers.
- A few i.MX7D device additions, watchdog, cortex-a7 coresight
components, RTC, power key, power off.
- Some Vybrid updates: add device support for I2C, QSPI, eSDHC etc.,
update ADC node, and define stdout-path property.
- A few random updates for i.MX27 and i.MX53 devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVyhktAAoJEFBXWFqHsHzOjQwH/0CXyzRUCJjHqxAHsnvHzOZG
AvjYWqaimxP5PD6TRG1bRxfWWXNL7zZGqj9Jd/l5HIWdWfUxnOLeMy40yfcs+AsH
9CHUunu0rahIDY6YF4gA7F5jyfnSIzxwE8Bkva7nmXvf0XmazTwhCXxYPzdBjMSG
Cf39datyTj9ZS3DD/DAKzRN//zebQCJmPuAdmIlRZljBkoLVPeEZrVxkSN0trRin
vKPQIpamM2DXIMmdiPK52J0j8Vwq4qbiGvvAwUKsaRCUVYfpunpVcZSYgMqm8iEa
7PKuurbVeuvZLzS0Bdq05tCkwVXt0upk0ayf0i8DkHFExX79TNTbONOLJwmigjo=
=iAvA
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree updates for 4.3:
- Add audio and eTSEC device support and update dspi node for LS1021A.
- Add initial i.MX6UL and imx6ul-14x14-evk board support, and enable
a bunch of device support for i.MX6UL, including RTC, power key, USB,
QSPI, and dual FEC.
- Enable HDMI and LVDS dual display support for a few imx6qdl boards.
- Support of imx6sl-warp board rev1.12, the version which will be
publicly available for the customers.
- A few i.MX7D device additions, watchdog, cortex-a7 coresight
components, RTC, power key, power off.
- Some Vybrid updates: add device support for I2C, QSPI, eSDHC etc.,
update ADC node, and define stdout-path property.
- A few random updates for i.MX27 and i.MX53 devices.
* tag 'imx-dt-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (44 commits)
ARM: dts: imx6ul: add snvs power key support
ARM: dts: imx6ul: add RTC support
ARM: dts: imx6ul: enable GPC as extended interrupt controller
ARM: dts: imx6sx: correct property name for wakeup source
ARM: dts: add property for maximum ADC clock frequencies
ARM: dts: imx7d: enable snvs rtc, onoffkey and power off
ARM: dts: imx6ul-14x14-evk: add fec1 and fec2 support
ARM: dts: imx: add fec1 and fec2 nodes for SOC i.MX6UL
ARM: dts: imx27: add support of internal rtc
ARM: dts: vf-colibri: define stdout-path property
ARM: dts: ls1021a: Enable the eTSEC ports on QDS and TWR
ARM: dts: ls1021a: Add the eTSEC controller nodes
ARM: dts: imx6ul: add qspi support
ARM: dts: imx6ul: fix low case define in imx6ul-pinfunc.h
ARM: dts: imx6ul: add usb host and function support
ARM: dts: vfxxx: Add io-channel-cells property for ADC node
ARM: dts: ls1021a: Add dts nodes for audio on LS1021A
ARM: imx6qdl-sabreauto.dtsi: enable USB support
ARM: dts: imx: update snvs to use syscon access register
ARM: dts: imx: add imx6ul and imx6ul evk board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Cortex-A9 SoCs and actually enabling usb on the rk3066-marsboard,
Two more veyron-devices - namely Speedy and Minnie and a fix for
the tsadc.
One slightly more interesting fix is the blocking of the last
16MB of memory on 4GB rk3288 devices. The rk3288 cannot use this
area for dma operations, so things like the mmc or usb controllers
regularly fail when trying to read data. This solution mimicks the
solution from the ChromeOS kernel, who also do not seem to have
found a better solution yet. Here it only moves to the devicetree.
As this issue is also present on the arm64 rk3368, any future
better solution to this problem would need to describe this in
the devicetree as well and could then remove this block.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJVxnMhAAoJEPOmecmc0R2BGXAH/03qzTWzHaLJH73zNj2+r7cm
GwlwxntSDb4e6lq5hKT1+biqBrin+IrzA1sCcyeiFlg3wOWP5AuuEyiKgVKHZ//c
9dKAVsmtX5TMliFPA+U6SvEyURPk5RSU30cTgYEEBVhwWhDduDnJOBmOpLhHyQUC
36FMlfNBpNQQHYQUNziXEgnWZNtvdiYnmt4FPkdQWT08kZKJvyky+gbqOkya4RzH
Pi70IzQyh3F0UiQR4f34q+C0+KStF9LdZSeYgnnY++Sg+5Wz9FAWcdoo2qwi2C8t
qVPEF2B1vW87+9z3WtGRk2CE48uy6QS7WQL3l/wHp6RxMCPXu9QjOAHOl2rBHSs=
=2Rte
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rockchip32-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Some more devicetree changes, including usbphy support for the
Cortex-A9 SoCs and actually enabling usb on the rk3066-marsboard,
Two more veyron-devices - namely Speedy and Minnie and a fix for
the tsadc.
One slightly more interesting fix is the blocking of the last
16MB of memory on 4GB rk3288 devices. The rk3288 cannot use this
area for dma operations, so things like the mmc or usb controllers
regularly fail when trying to read data. This solution mimicks the
solution from the ChromeOS kernel, who also do not seem to have
found a better solution yet. Here it only moves to the devicetree.
As this issue is also present on the arm64 rk3368, any future
better solution to this problem would need to describe this in
the devicetree as well and could then remove this block.
* tag 'v4.3-rockchip32-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add veyron-minnie board
ARM: dts: rockchip: reserve unusable memory region on rk3288
ARM: dts: rockchip: enable usb controller on marsboard
ARM: dts: rockchip: add usb phys to Cortex-A9 socs
ARM: dts: rockchip: set correct dwc2 params for cortex-a9 socs
ARM: dts: rockchip: Add veyron-speedy board
ARM: dts: rockchip: Use correct dts properties for tsadc node on veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
- device tree part of the Dove PMU series
- converting a new orion5x based platform to dt: Linkstation Mini
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlXE1doACgkQCwYYjhRyO9VyywCghy4yCyXWjfJ+rIE9uZ0JZwg7
TYcAmgKPY3lgL1cXdRTTo82iXRwRM3Ht
=ndrR
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.3-3' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt changes for v4.3 (part #3)
- device tree part of the Dove PMU series
- converting a new orion5x based platform to dt: Linkstation Mini
* tag 'mvebu-dt-4.3-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: Convert Linkstation Mini to Device Tree
ARM: dt: dove: add GPU power domain description
ARM: dt: dove: add video decoder power domain description
ARM: dt: dove: wire up RTC interrupt
ARM: dt: Add PMU node, making PMU child devices childs of this node
Signed-off-by: Olof Johansson <olof@lixom.net>
Initial version of DTSI for ProXstream2 and PH1-LD6b and DTS for
PH1-LD6b reference board.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[olof: sort Makefile entries]
Signed-off-by: Olof Johansson <olof@lixom.net>
Also known as the Asus Chromebook Flip.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
The title says it all. The name of the dts file as been changed to
better reflect the manufacturer's device name (LS-WSGL), rather than
the original "lsmini", which exists in a kirkwood version too.
[gregory.clement@free-electrons.com]: use tab instead of space to
indent dts at line 185. Reslove merge conflict with patch "ARM: dts:
orion5x: add buffalo linkstation ls-wtgl" in the file
arch/arm/boot/dts/Makefile.
Signed-off-by: Benjamin Cama <benoar@dolka.fr>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Alexey Kopytko <alexey@kopytko.ru>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
A bunch of device tree patches that:
- Enable the OTG controller on some boards
- Various additions to the existing boards
- New boards: A33 Ippo Q8H, Iteaduino Plus,
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ebRO
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner Device Tree changes for 4.3
A bunch of device tree patches that:
- Enable the OTG controller on some boards
- Various additions to the existing boards
- New boards: A33 Ippo Q8H, Iteaduino Plus,
* tag 'sunxi-dt-for-4.3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (35 commits)
ARM: dts: sun7i: Change cubietruck wifi enable pin to use mmc-pwrseq
ARM: dts: sun5i: hsg-h702: Enable USB OTG controller
ARM: dts: sun5i: hsg-h702: Enable side volume buttons with LRADC
ARM: dts: sun8i: Enable USB DRC on Ippo Q8H-A33 tablet
ARM: dts: sun5i: Enable USB DRC on A13 OLinuxIno
ARM: dts: sun5i: Enable USB DRC on A10s OLinuxIno Micro
ARM: dts: sun4i: Enable USB DRC on A10 OLinuxIno Lime
ARM: sunxi: dt: Convert users to the PIO interrupts binding
ARM: dts: sun4i: Add Iteaduino Plus A10
ARM: dts: A10s-OLinuxIno: Add a node for axp152 pmic
ARM: dts: axp152: Add a dtsi file for the axp152 pmic
ARM: dts: sun6i: Enable otg controller on the cs908
ARM: dts: sun4i: Enable otg controller on the mini-x
ARM: dts: sun4i: Enable otg controller on the ba10-tvbox
ARM: dts: sunxi: Add regulator-boot-on to usb host port regulator nodes
devicetree: Add msi to the vendor-prefix list
ARM: sun8i: dts: Add Ippo-q8h v1.2 with A33
ARM: dts: sun8i: sina33: Enable USB hosts
ARM: dts: sun8i: Enable USB host on GA10H-A33 tablets
ARM: dts: sun8i: Enable USB DRC on GA10H-A33 tablets
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Devkit8000 was sold with a 4.3" LCD or 7.0" or without. This patch
creates one dts file per bundle.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal support for the new sama5d2 Xplained board. Only USB,
spi/i2c, ethernet and uart/usart peripherals added.
With this DTS file you can boot the board and begin to play with it.
Rootfs on NFS and sd card have successfully been tested.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the initial device tree for the R8A7794 SoC based SILK low cost board.
SCIF2 serial port support is included, so that the serial console can work.
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Update clocking for DTS nodes
- Add DTS board file for Terasic DE0 Atlas board
- Use stdout-patch for chosen node
- Enable prefetch-data and prefetch-instr
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oSa1
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.3
- Update clocking for DTS nodes
- Add DTS board file for Terasic DE0 Atlas board
- Use stdout-patch for chosen node
- Enable prefetch-data and prefetch-instr
* tag 'socfpga_dts_for_v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: add osc1 as a possible parent for dbg_base_clk
ARM: socfpga: dts: add missing clock gates to socfpga.dtsi
ARM: socfpga: dts: Fix gpio dts entry for the correct clock
ARM: socfpga: dts: Correct the parent clock for l3_sp_clk and dbg_clk
ARM: dts: socfpga: Add support of Terasic DE0 Atlas board
ARM: dts: socfpga: use stdout-path for chosen node
ARM: dts: socfpga: enable the data and instruction prefetch for the l2 cache
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove Marzen legacy board code written in C. Instead
board support expressed in DT shall be used together
with Multiplatform and shmobile_defconfig.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
These changes make dm814x boot and adds minimal board support for
dm814x-evm and hp t410.
Note that to boot these depend on omap-for-v4.3/soc-signed branch,
but as dm814x support is currently broken, these can be merged
separately with the other dts changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TVm+
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/dt-dm814x' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
omap dts changes for minimal dm814x support for v4.3 merge window.
These changes make dm814x boot and adds minimal board support for
dm814x-evm and hp t410.
Note that to boot these depend on omap-for-v4.3/soc-signed branch,
but as dm814x support is currently broken, these can be merged
separately with the other dts changes.
* tag 'omap-for-v4.3/dt-dm814x' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Add custom abort handler for t410
ARM: dts: Add minimal support for HP T410
ARM: dts: Add minimal dts support for dm8148-evm
ARM: dts: Add minimal clocks for dm814x
ARM: dts: Add minimal dm814x support
Signed-off-by: Olof Johansson <olof@lixom.net>
Highlights:
-----------
- Add RCC clocks support to STM32F429
- Add STM32429i-EVAL board support
- Use stdout-path instead of linux,stdout-path in Disco board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FWox
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.3-1b' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32 into next/dt
STM32 DT updates for v4.3, round 1.
Highlights:
-----------
- Add RCC clocks support to STM32F429
- Add STM32429i-EVAL board support
- Use stdout-path instead of linux,stdout-path in Disco board
* tag 'stm32-dt-for-v4.3-1b' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/stm32:
ARM: dts: Use stdout-path in STM32F429 Discovery board
ARM: dts: Add STM32429i-EVAL board support
ARM: dts: stm32f429: Adopt STM32F4 clock driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Which is formally known as the Asus C201 chromebook
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Add missing devices for pandora. Note that we're adding wl1251
WLAN and LCD backlight support for now using legacy pdata as that
allows us to drop the legacy board file for pandora in another
series of patches
- Enable power button support for omap5-uevm
- Add aliases for am437x UARTs
- Add support for phyCORE phyBOARD-WEGA-AM335x rdk and
phyCORE-AM335x SoM
- Use u16 values for tsc2046 on omap3-lilly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVr0CtAAoJEBvUPslcq6VzLTYP/R1NItYVsfyi48ZrxjfG8sb+
y96eQ3HSaRqtiT88on/4hZvXs0JPMq+2t0IAqpNa9qe9Iua2VwQSM4pxdmt2sa56
lExkHUgu5/TrEFARRTwNCzt+oLOR6R2NwfwChGF25Qmywzy63wLmm5M5oZF+0gF1
MJdyhEUsELSxMfhrzcMmmEk+qHo2EomGUFtFkOCgkQo87BoUWzGu6QmhrfvwEh5e
pRgszqUzk9WEXlFe5VnW2u5FAP7ZDgVhQICsOYQWArwgwFRerMgt4O42XW1ZnDd0
luh0Q6qeVjYbtVXoSQn4QnQ5fQeO1FtOy4xkEJ5QzBrCrTy/yKIBhvh84bu6zLSV
ZLBkgVISFtykAal041IUmjARTzhPVJfR3jrFMPQe1/SCQr3BJAZVoLgFQq3PkQKd
2VAt5q9Eg+xAAn5rfcTgBRV8bvyjw5i9i6ZY0S1geppFFvl/msE9k6Ze7V801BKF
ERjRYwsvvyt5upNN0b1Cm/amSbpF4GXrX+7xbVjqLT8uYMWZPsNWo9hhHIxG/610
vx8Cq46KQfqfJZMcMet0dZ6EzFVQWAV8dkIHgLa0hblfKRzAQXm2B/iBKKOgZobT
hg5xbaIN24WU4dAmMbui/zBWgovkIiPglzglxIbY4a8WTXBVO+94Dq0/SLR0jJft
slStVq5hDvZAD51oqspS
=uvLA
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v4.3, part2" from Tony Lindgren:
More omap dts changes for v4.3 merge window:
- Add missing devices for pandora. Note that we're adding wl1251
WLAN and LCD backlight support for now using legacy pdata as that
allows us to drop the legacy board file for pandora in another
series of patches
- Enable power button support for omap5-uevm
- Add aliases for am437x UARTs
- Add support for phyCORE phyBOARD-WEGA-AM335x rdk and
phyCORE-AM335x SoM
- Use u16 values for tsc2046 on omap3-lilly
* tag 'omap-for-v4.3/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap3-pandora: add wifi support
ARM: OMAP2+: omap3-pandora: add backlight support
ARM: dts: omap3-pandora: add support for usb host and 32k buffer
ARM: dts: omap3-pandora: miscellaneous corrections
ARM: dts: omap5-uevm: Add Palmas power button support
ARM: dts: am437x: add aliases for all UART instances
ARM: dts: Add phyBOARD-WEGA-AM335x rdk
ARM: dts: Add support for phyCORE-AM335x SoM
ARM: dts: omap3: correct the format of u16 values for tsc2046 node
Signed-off-by: Olof Johansson <olof@lixom.net>
The Terasic DE0 Atlas board is also known as the DE0-Nano board.
This patch adds the DTS board file for the DE0-Nano Sockit board, and not
the DE0 Nano "Development Board".
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v3: Updated skew settings for the gmac1 node as this board is using the
KSZ9031 PHY instead of the 9021 PHY.
v2: use stdpath-out for console and remove comment regarding u-boot ethaddr
Iteaduino Plus A10 is a breakout board + Itead Core A10. It features 1GB RAM,
has most of the A10 pins on a .1" header, 2 USB ports, 1 OTG USB port,
Ethernet, HDMI, SATA, Speaker/Microphone 3.5mm jacks and an SD card slot.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
phyBOARD-WEGA-AM335x represents a direct soldered
combination of a phyCORE-AM335x SoM and carrier board.
Different kind of SoM options can be connected to
the wega carrier board. So we created a separate
wega dtsi file. The final dts contains the actual
SoM on the carrier board.
WEGA carrier board features:
* ETH phy on carrier board: 1x MII
* 1x CAN
* 2x UART
* USB0 (device)
* USB1 (host)
* mSD slot
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds basic chip support for Mediatek 6580.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
TV-boxes and the initial support for two Chromebooks from
the veyron family.
Additionally a non-critical fix for the watchdog irq
on rk3288, addition of the gmac reset line, a ramp delay
for the cpu regulator on the firefly board and cpu affinity
for the arm-pmu spi irqs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJVqBLGAAoJEPOmecmc0R2Bt2QIALKxbeZhRMHvw2CRwvpmsBqi
nAWxltDvi54OVqvVU8dkOFy5O6YlIZCf9ihuUobdEWp5zi+HYanp31Co03EutuTt
qEubdmZ/4MZHYDEQH6ABtsw6JrUKqZWtJhL2vomxSnbWGd8hW2WL12PsjL2BjIqw
8tSNq/rWqvs54QlgwcCXsXdPojQF7d8rzX+M2mRREawymklDAv6hps8uigw+fcE2
TI3V3HrefZPpi8dVkfs+kCKCs96wlnjZkY3dl/T7XZpyoAwOicVTwqKxrPG9wnPj
W0wviF52i2szD/riZUm1fE7C6QeJ7iPX8Yz249ZhksJJWDsCKAloZtVDbNgcSI0=
=YGmG
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rockchip32-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Rockchip dts changes for 4.3, part1" from Heiko Stuebner:
This adds the board for the Netxeon R89 used in different TV-boxes and
the initial support for two Chromebooks from the veyron family.
Additionally a non-critical fix for the watchdog irq on rk3288, addition
of the gmac reset line, a ramp delay for the cpu regulator on the firefly
board and cpu affinity for the arm-pmu spi irqs.
* tag 'v4.3-rockchip32-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add rk3288 arm-pmu irq affinity
dt-bindings: document rk3368 R88 board from Rockchip
ARM: dts: rockchip: add missing device_type = "memory" to boards
ARM: dts: rockchip: add veyron-pinky board
ARM: dts: rockchip: add veyron-jerry board
ARM: dts: rockchip: add shared rk3288-veyron files
ARM: dts: Add sbs-battery dts fragment used by chromebooks
ARM: dts: rockchip: add Netxeon R89 board
dt-bindings: add vendor prefix for Netxeon Technology
ARM: dts: rockchip: fix rk3288 watchdog irq
ARM: dts: rockchip: Add ramp delay for vdd_cpu in firefly board dts
ARM: dts: rockchip: Add STMMAC reset signal in GMAC interface for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
- Update Armada 388 GP description
- Add Buffalo Linkstation LS-WXL and LS-WSXL
- Fine-tune the L2 configuration for cortex A9 based SoC
- Update XOR definition for Armada 38x and 39x SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlWnty8ACgkQCwYYjhRyO9WyngCglAnXHxZDs/J1BPGui8NytWxu
OsAAnjLqe8k6n0nA3qEpXPkN3DV8ZlHO
=WFZw
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.3-1' of git://git.infradead.org/linux-mvebu into next/dt
Merge "ARM: mvebu: dt changes for v4.3" from Gregory Clement:
mvebu dt changes for v4.3 (part #1)
- Update Armada 388 GP description
- Add Buffalo Linkstation LS-WXL and LS-WSXL
- Fine-tune the L2 configuration for cortex A9 based SoC
- Update XOR definition for Armada 38x and 39x SoC
* tag 'mvebu-dt-4.3-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: update EEPROM description of Armada 388 GP
ARM: mvebu: fix description of pwr-sata0 regulator on Armada 388 GP
ARM: dts: add buffalo linkstation ls-wvl/vl
ARM: dts: add buffalo linkstation ls-wxl/wsxl
ARM: mvebu: use DT properties to fine-tune the L2 configuration
ARM: mvebu: use armada-380-xor on Armada 38x and 39x
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "LPC18xx DTS changes for 4.3" from Joachim Eastwood:
This patch set adds DT nodes for all the drivers that went upstream in
4.2 and should represent the bulk of DTS changes for 4.3. All nodes
added are documented and some of patches carries a ack from subsystem
maintainer. It also features updates to the EA4357 dev- kit and a new
board from Ezequiel Garcia.
Note that there might be one more batch of DTS changes for 4.3 if any
new drivers goes upstream and also some changes for the Hitex eval board
might come.
* 'lpc18xx_43xx_dts_4.3' of https://github.com/manabian/linux-lpc:
ARM: dts: add DT for CIAA LPC4337 industrial computer
of: add vendor prefix for CIAA project
ARM: dts: lpc4357-ea4357: add uart3
ARM: dts: lpc4357-ea4357: add ethernet
ARM: dts: lpc4357-ea4357: add gpio joystick
ARM: dts: lpc4357-ea4357: add mmcsd
ARM: dts: lpc4357-ea4357: add pinctrl and uart0 muxing
ARM: dts: lpc18xx: add usb nodes
ARM: dts: lpc18xx: add ethernet node
ARM: dts: lpc18xx: add creg (syscon) node
ARM: dts: lpc18xx: add mmcsd node
ARM: dts: lpc18xx: add can nodes
ARM: dts: lpc18xx: add ssp nodes
ARM: dts: lpc18xx: add gpio node
ARM: dts: lpc18xx: add pinctrl node
ARM: dts: lpc18xx: add uart new compat string and clk names
ARM: dts: lpc18xx: add cgu and ccu clock-controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
While pinky was one of the earlier development models, is on the list
of endangered species today and nearly extinct, I want to keep mine
around for the foreseeable future after spending all the time making a
nice hole into the base below the dut-connector.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Hisense Chromebook C11, also named jerry.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
changes for reemoteproc platform_data and audio options for
omap2plus_defconfig to keep audio working when changing boards
to use SIMPLE_CARD. The summary of changes is:
- A large set of audio related changes for SIMPLE_CARD from
Peter Ujfalusi <peter.ujfalusi@ti.com> for am335x and am437x
- Pinctrl dts defines for dra7 virtual mode to configure timings
- Change to use cpsw slave0 for dra7 Ethernet
- Remove unconfigured and wrong l3-mux entry for dm816x
- Add support for Gumstix Palo35 and TobiDuo boards, and Overo
PoP NAND and McBSP2
- Start using new HDMI binding for tilcdc
- Start using new sDMA crossbar for dra7
- Start using rproc for am335x and am437x M3 coprocessor
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sPfQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v4.3, part 1" from Tony Lindgren:
Omap dts changes for v4.3 merge window. There are also related
changes for reemoteproc platform_data and audio options for
omap2plus_defconfig to keep audio working when changing boards
to use SIMPLE_CARD. The summary of changes is:
- A large set of audio related changes for SIMPLE_CARD from
Peter Ujfalusi <peter.ujfalusi@ti.com> for am335x and am437x
- Pinctrl dts defines for dra7 virtual mode to configure timings
- Change to use cpsw slave0 for dra7 Ethernet
- Remove unconfigured and wrong l3-mux entry for dm816x
- Add support for Gumstix Palo35 and TobiDuo boards, and Overo
PoP NAND and McBSP2
- Start using new HDMI binding for tilcdc
- Start using new sDMA crossbar for dra7
- Start using rproc for am335x and am437x M3 coprocessor
* tag 'omap-for-v4.3/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (32 commits)
ARM: dts: am335x-evm: Switch using simple-audio-card for audio support
ARM: dts: am335x-evm: Add sleep pin settings for mcasp1
ARM: dts: am335x-evm: Rename pinctrl section for McASP1
ARM: dts: am335x-evm: Fix mcasp1 node's indentation
ARM: dts: am335x-evmsk: Switch using simple-audio-card for audio support
ARM: dts: am335x-evmsk: Add sleep pin settings for mcasp1
ARM: dts: am335x-evmsk: Fix mcasp1 node's indentation
ARM: dts: am437x-gp-evm: Enable analog audio via simple-card
ARM: dts: am437x-gp-evm: McASP1 node for audio support
ARM: dts: am437x-gp-evm: Add node for tlv320aic3106 audio codec
ARM: dts: am437x-gp-evm: Rename fixed regulator vmmcsd_fixed to evm_v3_3d
ARM: dts: am437x-gp-evm: Add gpio-hog for configuring the display/audio mux
ARM: dts: am43xx-epos-evm: Enable analog audio via simple-card
ARM: dts: am43xx-epos-evm: Add node for tlv320aic3111 audio codec
ARM: dts: am43xx-epos-evm: McASP1 node for audio support
ARM: dts: am43xx-epos-evm: Add regulator for VBAT and DCDC4 of tps65218
ARM: dts: am43xx-epos-evm: Add gpio-hog for configuring the display/audio mux
ARM: dts: am437x-sk-evm: Switch using simple-audio-card for audio support
ARM: dts: am437x-sk-evm: Add sleep pin settings for mcasp1
ARM: omap2plus_defconfig: Enable audio related config options
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This board is used in some TV-boxes like for example the Beelink R89 or
Tronsmart R28.
The board itself follows the reference design for the most part. But
there are no schematics available it seems, so some things should be
taken with a grain of salt.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Romain Perier <romain.perier@gmail.com>
Add basic support for CIAA (Argentine Open Industrial Computer)
LPC4337 board. This commit enables the following peripherals:
* UART
* SSP
* Ethernet
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Also, reduce the maximum SPI device speed to the max. supported by the
LCD controller used on the LGPhilips LB035Q02 panel for this board.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Gumstix "Tobi-Duo" expansion board [1] can be used with either
OMAP3 Overo or Overo Storm COMs. It provides two NICs using LAN9221
chips.
It is necessary to duplicate the interface information for the
second SMSC9221 chip as discussed [2].
[1] https://store.gumstix.com/index.php/products/241/
[2] http://www.spinics.net/lists/linux-omap/msg115282.html
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add dts file to support Buffalo Linkstation LS-WVL and LS-VL,
which are 3.5" HDD NAS in 2-bay and 1-bay respectively.
[gregory.clement@free-electrons.com: fix typo in pmx-led-function-red]
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add dts file to support Buffalo Linkstation LS-WXL and LS-WSXL,
which are 2-bay NAS with 3.5" and 2.5" HDD respectively.
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Ippo-q8h is a tablet circuit board commonly found in cheap Android
tablets. The v1.2 version can be used with either an A23 or A33 SoC.
This version features 512 MB DRAM, 4G NAND, MMC, LCD, capacitive
touchscreen, accelerometer, 2 camera sensors, USB OTG, microphone
and speakers.
i2c0 is connected to the gsl1680 capacitive touch panel controller,
i2c1 is connected to an mma7660 3-axis accelerometer, these peripherals are
not supported by the kernel yet, i2c bus functionality has been tested via
i2c-dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[maxime: Removed the resolution mention, and modified the compatible to
have a unique one with the A23 version]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Minimal DT description and Makefile entry for the Gose eval board.
Support for console, timer, and Ethernet.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The legacy board code for Armadillo-800 EVA has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The legacy board code for KZM-A9-GT has been removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As usual, quite a few device-tree updates in ARM land. There was ome
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey
Conflicts: None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wWIc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Kevin Hilman:
"As usual, quite a few device-tree updates in ARM land. There was one
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
ARM: hisi: revert changes from hisi/hip04-dt branch
ARM: nomadik: set proper compatible for accelerometer
ARM64: juno: add GPIO keys
ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
ARM: dts: Introduce STM32F429 MCU
ARM: socfpga: dts: enable ethernet for Arria10 devkit
ARM: dts: k2l: fix the netcp range size
ARM: dts: k2e: fix the netcp range size
ARM: dts: k2hk: fix the netcp range size
ARM: dts: k2l-evm: Add device bindings for netcp driver
ARM: dts: k2e-evm: Add device bindings for netcp driver
ARM: dts: k2hk-evm: Add device bindings for netcp driver
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
arm64: dts: Add dts files for Hisilicon Hi6220 SoC
clk: hi6220: Document devicetree bindings for hi6220 clock
arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
...
Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC
Conflicts:
arch/arm/mach-socfpga/core.h
Trivial remove/remove conflict with our cleanup branch.
Resolution: remove both sides
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZtPK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform support updates from Kevin Hilman:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
ARM: socfpga: fix build error due to secondary_startup
MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
ARM: ep93xx: simone: support for SPI-based MMC/SD cards
MAINTAINERS: update Shawn's email to use kernel.org one
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
...
Add initial dts file and document for ZX296702 and board ZX296702-AD1.
More peripherals will be added later.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
- use labels for overriding nodes for all of exynos stuff
(by Krzysztof Kozlowski)
- add sysmmu nodes for exynos SoCs (by Marek Szyprowski)
- for exynos5422-odroidxu3
: enalbe wake alarm of S2MPS11 RTC
: Hook up PWM and use it for LEDs
: add support for Odroid XU3 Lite
- remove duplicated i2c7 for exynos5250-snow
- add JPEG codec nodes for exynos5420
- add vendor prefix for Hardkernel
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZQaR
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung another DT udpates for v4.2
- use labels for overriding nodes for all of exynos stuff
(by Krzysztof Kozlowski)
- add sysmmu nodes for exynos SoCs (by Marek Szyprowski)
- for exynos5422-odroidxu3
: enalbe wake alarm of S2MPS11 RTC
: Hook up PWM and use it for LEDs
: add support for Odroid XU3 Lite
- remove duplicated i2c7 for exynos5250-snow
- add JPEG codec nodes for exynos5420
- add vendor prefix for Hardkernel
* tag 'samsung-dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (33 commits)
ARM: dts: add sysmmu nodes for exynos5420
ARM: dts: add sysmmu nodes for exynos5250
ARM: dts: add sysmmu nodes for exynos4415
ARM: dts: add sysmmu nodes for exynos3250
ARM: dts: add sysmmu nodes for exynos4
ARM: dts: Add Odroid XU3 Lite support
of: Add vendor prefix for Hardkernel
ARM: dts: odroidxu3: Enable wake alarm of S2MPS11 RTC
ARM: dts: exynos5420: add nodes for jpeg codec
ARM: dts: s3c2416: Use labels for overriding nodes in SMDK2416
ARM: dts: s3c2416: Add labels to S3C2416 nodes
ARM: dts: Use labels for overriding nodes in exynos5422-odroidxu3
ARM: dts: Use labels for overriding nodes in exynos5440 boards
ARM: dts: Use labels for overriding nodes in exynos5420-smdk5420
ARM: dts: Use labels for overriding nodes in exynos542x
ARM: dts: Use labels for overriding nodes in exynos5420-arndale-octa
ARM: dts: Remove duplicated I2C7 nodes in exynos5250-snow
ARM: dts: Use labels for overriding nodes in exynos5250
ARM: dts: Add labels to exynos5 nodes
ARM: dts: exynos5422-odroidxu3: Hook up PWM and use it for LEDs
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVa7zvAAoJEHm+PkMAQRiGtfMIAILs3sxFtrC1hApgcfRLF/7z
K34bwTRqErzqUO/orTwakEr9kSIpIL0zIPSryTCOTPZLfMGkQjhHXO3KR/DSbbTV
MZ8y/BM/yelFA/Np+1LjbiYjTNRnTRvCoaQihkIH8Rn02g7ob9HyL4gIGKpuGFcZ
04GacL2cgChqsRSACdNef948jCoJXKgcuDpe39DXphDWZnBKNZ3HFuJ6bryGJf9A
1/eCI4is85BNwKPemQUYR0xx83UIzDfrghatZP2mOCDDSA2MNg8HNxLTd12LGoQD
tfgX4B7aftzW9Y7GSEDfZ0IKm2NRzgPmCVj6PjVR/iI0lIK4Aq0Z/lDJxxEq3XQ=
=AJM5
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc6' into next/dt
Linux 4.1-rc6
Conflicts:
arch/arm/boot/dts/zynq-7000.dtsi
Resolution summary:
Mainline had an earlier version of the commit, resolve in favor of the
newer patch in next/dt branch.
- rtc node for at91sam9rl/at91sam9rlek
- move to stdout-path for console on kizbox and all Atmel's boards
- Addition of the Acme Systems' Arietta G25
- two little fixes for Kizbox and sama5d4ek
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVcZyfAAoJEAf03oE53VmQv+sH+wbJx4PN0KdgGQXhOzj/UBRp
6LU4LZGGmCTxM0+FRDH9Bepjwwr8iiHTfaNPnM3bgDrEj3Ik43ekMLqgtIwrkIn2
YRfZY0t4oPZIte+weBAqDl7qHVKaVlttbZABEAVI2rQgui+LAj6T4u3rmUsvoPHU
j8NP6Ng7mWD6nb31ulrPezo33cz8jutoPerWIzclWa+sJhB4bHZHb7N4z7SvouDG
SXlvq5HkK2Az3DwT+RgHyqzSAVa/zl+rOce5LhOgD1I0p3OCPJ+aO0oxQJOaS48F
JmLsEY6xO3wavMFm5z/AHOD+sJej+iGpmHf6EwF93OVtiu83wfxIWml+xQdcjNg=
=FN7g
-----END PGP SIGNATURE-----
Merge tag 'at91-dt4' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Fourth batch of DT changes for 4.2:
- rtc node for at91sam9rl/at91sam9rlek
- move to stdout-path for console on kizbox and all Atmel's boards
- Addition of the Acme Systems' Arietta G25
- two little fixes for Kizbox and sama5d4ek
* tag 'at91-dt4' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
ARM: at91/dt: Add Acme Arietta G25
ARM: at91/dt: sama5d4 xplained: use stdout-path
ARM: at91/dt: sama5d4ek: use stdout-path
ARM: at91/dt: sama5d3 xplained: use stdout-path
ARM: at91/dt: sama5d3xek: use stdout-path
ARM: at91/dt: at91sam9x5ek: use stdout-path
ARM: at91/dt: at91sam9rlek: use stdout-path
ARM: at91/dt: at91sam9n12ek: use stdout-path
ARM: at91/dt: at91sam9m10g45ek use stdout-path
ARM: at91/dt: at91sam9g20ek: use stdout-path
ARM: at91/dt: at91sam9263ek: use stdout-path
ARM: at91/dt: at91sam9261ek: use stdout-path
ARM: at91/dt: at91rm9200ek: use stdout-path
ARM: at91/dt: kizbox: use stdout-path
ARM: at91/dt: at91sam9rlek: add RTC
ARM: at91/dt: at91sam9rl: fix rtc node
- Add device tree for i.MX7D SoC and imx7d-sdb board
- New i.MX6 board support: Armadeus Systems APF6, Gateworks GW5510,
and aristainetos2 boards
- Change LVDS to use simple-panel for nitrogen6x and sabrelite boards
- Add Wifi/Bluetooth devices support for cubox-i board
- Remove unused regulators and correct OTG roles setting for
imx6sl-warp board
- Add I2C support for imx23-olinuxino board
- Move imx6qdl HDMI device to a better place
- Add power-domain for imx6qdl CODA device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVb7iWAAoJEFBXWFqHsHzOIGEIAJjoZ+80PKH6+obh7gCuEkIx
MkZobKxYyRRh+wD+7NZEqSPMYxBW6eUCYGCCy+f/4xjmlIfHkp/DaaCeIU0EZItl
GU1ZE7qg6kWGbamun7zXcrg1cZ+bFOpQ926isETurL8LC2+PLm6OSg1pl6hwjqpA
rGzY2aEH5Lke6wDN0cMus0ApMlIQ8HpOLABtqosuzUWclyZBmoxBQshbW8ztzS3Y
pjpRfAHS91+0vZpoqmULTc/ENbTToNYk5NxJgMMDigkz1Gqp0Ni+rxmDmRPayo09
/Nq4VHDT+wx3CSf6nC9YIrabxrBMpvTky2jWOAJ4OxMFjT0xle3XISGRoa1ifqo=
=PbGi
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree changes for 4.2:
- Add device tree for i.MX7D SoC and imx7d-sdb board
- New i.MX6 board support: Armadeus Systems APF6, Gateworks GW5510,
and aristainetos2 boards
- Change LVDS to use simple-panel for nitrogen6x and sabrelite boards
- Add Wifi/Bluetooth devices support for cubox-i board
- Remove unused regulators and correct OTG roles setting for
imx6sl-warp board
- Add I2C support for imx23-olinuxino board
- Move imx6qdl HDMI device to a better place
- Add power-domain for imx6qdl CODA device
* tag 'imx-dt-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (24 commits)
ARM: dts: imx6dl: add imx6dl gpt specific compatible string
ARM: dts: imx6: add DT for aristainetos2 board
ARM: dts: cubox-i/hummingboard: Fix the license text
ARM: dts: sabrelite: use simple-panel instead of display-timings for LVDS0
ARM: dts: nitrogen6x: use simple-panel instead of display-timings for LVDS0
ARM: dts: add imx7d-sdb support
ARM: dts: add imx7d soc dtsi file
ARM: dts: Armadeus Systems APF6 family support (i.MX6)
ARM: dts: vf610: Nomenclature fixup for PTC12 pin used in RMII mode.
ARM: dts: cubox-i: add support for Broadcom Wifi/Bluetooth devices
Document: dt: binding: imx: update document for imx7d support
ARM: dts: imx6qdl: Add power-domain phandle to CODA device node
ARM: dts: Gateworks GW5510 support (i.MX6)
ARM: dts: imx6sl-warp: Fix OTG roles
ARM: dts: imx6sl-warp: Remove USB regulators
ARM: dts: imx6sl-warp: Remove unused regulator
ARM: dts: add pinfunc include file to support imx7d
ARM: mxs: fix in tree users of ssd1306
ARM: dts: imx6qdl-hummingboard: Add PCIe support
ARM: dts: imx23-olinuxino: Add i2c support
...
This pull request contains Broadcom BCM5301x related changes:
- Hauke adds the interrupt mapping for the BCM5301x PCIe controller
- Haule adds support for NAND flash using the standard Broadcom NAND controller
iProc specific binding on BCM4708/5301x
- Rafal adds support for the Asus RT-AC87U router
* tag 'arm-soc/for-4.2/dts-part3' of https://github.com/Broadcom/stblinux:
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
The STMicrolectornics's STM32F429 MCU has the following main features:
- Cortex-M4 core running up to @180MHz
- 2MB internal flash, 256KBytes internal RAM
- FMC controller to connect SDRAM, NOR and NAND memories
- SD/MMC/SDIO support
- Ethernet controller
- USB OTFG FS & HS controllers
- I2C, SPI, CAN busses support
- Several 16 & 32 bits general purpose timers
- Serial Audio interface
- LCD controller
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
A bunch of new DT changes for the 4.2 merge window, among which:
- Enable the SRAM controller on the A10/A10s/A13/A20
- A33 support
- New boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EHR7
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.2-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner DT changes for 4.2, take 2
A bunch of new DT changes for the 4.2 merge window, among which:
- Enable the SRAM controller on the A10/A10s/A13/A20
- A33 support
- New boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G
* tag 'sunxi-dt-for-4.2-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun6i: Add a dts file for the Mele A1000G quad top set box
ARM: dts: sun8i: Add dts file for the GA10H-A33 tablet
ARM: dts: sun8i-a33: Add dts for Sinlinx SinA33 development board.
ARM: dts: sun8i-a33: Add pinmux setting for uart0 on PB pins
ARM: dts: sun8i: Add pinmux setting for 8bit mmc2
ARM: dts: sun8i: Add usb_clk node for a23/a33
ARM: dts: sun8i: Add ET-Q8 A33 support
ARM: dts: sun8i: Add sun8i-a33 dtsi
ARM: dts: sun8i: Add sun8i-a23-a33 dtsi
ARM: dts: sun7i: Add A20 SRAM and SRAM controller
ARM: dts: sun5i: Add A10s and A13 SRAM and SRAM controller
ARM: dts: sun4i: Add A10 SRAM and SRAM controller
ARM: dts: sunxi: Revert SRAM controller drivers patches
ARM: dts: sun9i: Add device node for watchdog
ARM: dts: sun7i: Add uart4 support for BananaPro, disable uart2
ARM: dts: sun7i: Add uart4_pins_b definition
ARM: sun8i: Introduce A23 Evaluation Board Support
This patch adds support for the imx6dl based aristainetos2 board
with following configuration:
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
MReset cause: POR
MBoard: aristaitenos2
DRAM: 1 GiB
NAND: 1024 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Display: lb07wv8 (800x480)
As this board can be used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Add support for the Gateworks GW5510 board featuring:
* i.MX6 SoC
* up to 512MB DDR3
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI) (currently supported by only vendor kernel)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
For more details see:
http://www.gateworks.com/product/item/ventana-gw5510-single-board-computer
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The Odroid XU3 Lite is almost the same as XU3, except:
1. Lower CPU frequencies (1.8 GHz for A15 and 1.3 GHz for A7, instead of
2.0 GHz and 1.4 GHz).
2. No DisplayPort.
3. No TI INA231 energy measurement sensors.
This patch moves common nodes (which is almost everything) to a common
DTSI file and adds a new XU3 Lite DTS.
Currently in comparison to XU3, only the INA231 sensors are disabled to
remove the warning:
ina2xx 0-0040: error configuring the device: -6
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been using
the same dts for both models. Unfortunately this does not work for the otg
controller, on the M9 this is routed to a micro-usb connector on the outside,
while as on the A1000G-quad it is connected to an usb to sata bridge
(which is not populated on the M9 pcb).
This commit adds a new dts for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ga10h is an 10" tablet with an A33 or A23 soc, 1G RAM, 8G or 16G nand,
sdio wifi, 2 micro usb ports, 1 otg and 1 host and 1 micro sd slot.
This commit adds a dts file for the v1.1 pcb with an a33 soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SinA33 is a core/SDK development board by Sinlinx. The core board
does not have any connectors or pads, other than the pads used to connect
it to the SDK board.
The core board only has the A33 SoC, 2 RAM chips, an eMMC flash chip,
the AXP223 PMIC, and supporting discrete components. eMMC is optional.
The SDK board has a USB host, USB OTG, volume control and home buttons,
audio input/output jacks, a micro-SD slot, camera and SDIO expansion
headers, an LCD connector, and a GPIO expansion header, which has
UARTs, MIPI DSI and I2C available. Only UART0 is enabled though.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
ET-Q8_A33 is A33 based cheap tablet in common Q8 format.
It has 512MB RAM, 4GB Nand, 7" Display, RDA5900P wifi, GSL1680 touch, etc.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Add 2 new set boards:
- Armada 385 based Linksys boards
- DLink DNS-327L
Update the spi-nor flash compatible strings
Use improved armada spi device tree compatible name for each mvebu SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVo3bwACgkQCwYYjhRyO9UxNgCgn5KoYMnx0qzbbmc7rfoyd9g3
IF8An0yb+2EFpP7SBPu41s8rXOATCCTb
=APjz
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.2-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt changes for v4.2 (part #2)" from Gregory CLEMENT:
Add 2 new set boards:
- Armada 385 based Linksys boards
- DLink DNS-327L
Update the spi-nor flash compatible strings
Use improved armada spi device tree compatible name for each mvebu SoC
* tag 'mvebu-dt-4.2-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: use improved armada spi device tree compatible name for each SoC
ARM: mvebu: dts: Add dts file for DLink DNS-327L
ARM: mvebu: add "jedec,spi-nor" flash compatible binding
ARM: kirkwood: add "jedec,spi-nor" flash compatible binding
ARM: mvebu: add support for the new Armada 385 based Linksys boards
The A23 Evaluation Board has an MMC slot, two UARTs, NAND, a few display
connectors (RGB, MIPI, LVDS), a mini-PCIE slot, USB host and OTG and a
bunch of embedded sensors.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MmxV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree related changes for omaps" from Tony Lindgren:
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
* tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: add mmc3 and wlan definitions to dts
ARM: dts: Enable SDIO card interrupt for 37xx-evm
ARM: dts: Fix ldp gpio keys to use defines
ARM: dts: Beaglebone i2c definitions
ARM: dts: am437x-gp-evm: add DT nodes for ov2659 sensor
ARM: dts: add DTS for Baltos IR5221
ARM: dts: omap5-uevm: Add Uart wakeup interrupt
ARM: dts: omap3-gta04: Add GSM audio support
ARM: dts: am335x-evm: add bluetooth support
ARM: dts: am437x-gp-evm: add wilink8 support
ARM: dts: omap3-gta04: Add hdqw1 support
ARM: dts: add core2 padconf region for am3517
ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit
ARM: OMAP3: Add support for configuring MMC pins as GPIO pins
Add support for Lightwriter SL50 series board, a small, robust and portable
Voice Output Communication Aids (VOCA) designed to meet the particular and
changing needs of people with speech loss resulting from a wide range of
acquired, progressive and congenital conditions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Andy Simpkins <andy.simpkins@toby-churchill.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DNS-327L is a 2-bay NAS with the following specs:
- 512MiB RAM
- 128MiB NAND Flash
- 1 GbE interface (Marvell PHY)
- 1 rear USB 3.0 port (via PCIe USB 3.0 controller)
- 2 internal SATA ports handled by the Armada 370:
uses 2 gpios for power control
- two front 2-color leds (amber + white) for both discs,
controlled by the SoC
- One white LED handled by SoC (USB)
- 3 buttons. Power handled by weltrend, USB and
RESET (on the bottom) are wired via GPIOs
- Unidentified i2c device at address 0x13 (via i2cdetect)
- UART0 providing serial console
- Weltrend MCU serving for RTC, temperature, fan control,
and power button handling interfaced via UART1
(Handled via userspace dns320l-daemon)
Signed-off-by: Andrew Andrianov <andrew@ncrmnt.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds support for the Linksys WRT1200AC (Caiman) and
the Linksys WRT1900AC v2 (Cobra).
Both boards have:
- 2 Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 512MB RAM
gregory.clement@free-electrons.com: use serial0:115200n8 in
stdout-path and remove the bootargs part in the chosen node
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This adds an initial device tree to run Linux on the Cortex-M4 on
the Vybrid based Colibri VF61 module.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This device is an industrial PC based on
AM335x SoC.
[ balbi@ti.com : updated to fit current mainline ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LogicPD Torpedo DM3730 devkit consists of a base board and
two processor boards. One of the processor boards has a WLAN and
the other one does not.
Let's set up basic dts file so we can move to device tree only
based booting over next few merge windows. So far I've tested
that UARTs, MMC1, USB OTG, smsc911x, and basic PM support works.
Note that the wireless support in kernel for wl1283 seems to be
broken, it tries to load wl127x-nvs.bin instead of wl128x-nvs.bin
with firmware.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The i.MX27 dtb build should be controlled by CONFIG_SOC_IMX27 rather
than CONFIG_SOC_IMX31.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fixes: cb612390e5 ("ARM: dts: Only build dtb if associated Arch and/or SoC is enabled")
Cc: <stable@vger.kernel.org>
Add basic support for Hitex LPC4350 Evaluation Board. Board
features a LPC4350 Soc, 8 MB SDRAM, 8 MB SPI Flash, USB and
Ethernet.
More information can be found on:
http://www.hitex.com/index.php?id=3212
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds basic support for Embedded Artists' LPC4357 Developer's Kit. Board
features a LPC4357 Soc, 32 MB SDRAM, 128 MB NAND Flash, 16 MB SPI
Flash, USB and Ethernet.
More information can be found on:
http://www.embeddedartists.com/products/kits/lpc4357_kit.php
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A series adding support for the Compulab CM-A510
- Add alias for mdio on Armada 38x
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVV6S0ACgkQCwYYjhRyO9W1tQCghag9/kiZ0qMJSesLBLwG7tcE
yrcAniOoTLzP6cMF+jqtuTrXwoke13JN
=OfeD
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt changes for v4.2 (part #1)" from Gregory CLEMENT:
- A series adding support for the Compulab CM-A510
- Add alias for mdio on Armada 38x
* tag 'mvebu-dt-4.2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add alias for mdio on Armada 38x
ARM: dts: dove: Add Compulab SBC-A510 to Makefile
ARM: dts: dove: Add proper support for Compulab CM-A510/SBC-A510
ARM: dts: dove: Remove Compulab CM-A510 from Makefile
ARM: dts: dove: Add internal i2c multiplexer node
Merge "Device Tree changes" from Florian Fainelli:
New devices:
- Felix adds support for the Buffalo WXR-1900DHP and adds the USB led on Buffalo
WZR-1750DHP
- Rafal adds support for the SmartRG SR400ac, Asus RT-AC68U and RT-AC56U
New peripheral support:
- Brian adds Device Tree nodes for the Broadcom NAND controller found on
BCM7xxx, BCM63138 and Cygnus SoCs
- Brian adds Device Tree nodes for the SATA AHCI and PHY controller found on
BCM7xxx
- I add the Device Tree nodes and bindings documents for bringing-up secondary
CPUs and timer/syscon-reboot on BCM63138
* tag 'arm-soc/for-4.2/dts' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Add DT for Asus RT-AC56U
ARM: BCM5301X: Add DT for Asus RT-AC68U
ARM: dts: BCM63xx: Add timer and syscon-reboot nodes
dt-bindings: Add documentation for the BCM63138 timer and syscon-reboot
ARM: dts: brcmstb: add nodes for SATA controller and PHY
ARM: dts: cygnus: Enable NAND support for Cygnus
ARM: bcm63138: add NAND DT support
ARM: bcm7445: add NAND to DTS
ARM: BCM5301X: Add DT for SmartRG SR400ac
ARM: BCM5301X: Add DT for Buffalo WXR-1900DHP
ARM: BCM5301X: Add USB LED for Buffalo WZR-1750DHP
ARM: dts: BCM63xx: Add SMP nodes and required properties
Documentation: DT: Document SMP DT nodes and properties for BCM63138
ARM: dts: BCM63xx: Add PMB busses nodes
Documentation: DT: Add Broadcom BCM63138 PMB binding
All the device tree related changes for the 4.1 merge window.
It has a rather big diffstat, because of a lot of mechanical and harmless
changes, as described below.
There is mostly:
- The end of the DT relicensing. All our DT should now be under the dual
X11/GPL license.
- Convertion of all the DT to a label based syntax, instead of
duplicating the tree like was done before.
- Rework of the A10s and A13 DTSI to share the common devices
- A few drivers enablings: A80 USB, the A31 PMIC, A31 and A23 arch
timers, etc
- Fix the checkpatch warnings
- A few new boards : cubieboard4, mele i7, utoo p66, auxtex t004,
pcduino3 nano, gemei G9, mk808c, jesurun q5, orange pi, orange pi mini
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6TQo
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT additions for 4.1, take 1" from Maxime Ripard:
All the device tree related changes for the 4.1 merge window.
It has a rather big diffstat, because of a lot of mechanical and harmless
changes, as described below.
There is mostly:
- The end of the DT relicensing. All our DT should now be under the dual
X11/GPL license.
- Convertion of all the DT to a label based syntax, instead of
duplicating the tree like was done before.
- Rework of the A10s and A13 DTSI to share the common devices
- A few drivers enablings: A80 USB, the A31 PMIC, A31 and A23 arch
timers, etc
- Fix the checkpatch warnings
- A few new boards : cubieboard4, mele i7, utoo p66, auxtex t004,
pcduino3 nano, gemei G9, mk808c, jesurun q5, orange pi, orange pi mini
* tag 'sunxi-dt-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (84 commits)
ARM: sunxi: dt: Split the SPI pinctrl groups
ARM: sunxi: dt: Fix whitespace errors
ARM: sunxi: DT: Fix lines over 80 characters
ARM: sunxi: dt: Remove the FSF address
ARM: sunxi: dts: split IR pins for A10 and A20
ARM: sun7i: dt: Add new MK808C device
ARM: dts: sun6i: Set PLL6 as parent to AHB1 clock in AHB1 clock node
ARM: dts: sunxi: Update ahb clocks for sun5i and sun7i
ARM: dts: sun7i: Add dts file for the Jesurun Q5 top set box
ARM: dts: sun5i: Enable touchscreen on Utoo P66
ARM: dts: sun7i: Add dts file for the Orangepi mini SBC
ARM: dts: sun7i: Add dts file for the Orangepi SBC
ARM: dts: sun7i: Add A20 SRAM and SRAM controller
ARM: dts: sun5i: Add A13 and A10s SRAM and SRAM controller
ARM: dts: sun4i: Add A10 SRAM and SRAM controller
ARM: dts: sun5i: Add broken-hpi property for Utoo-P66 eMMC
ARM: sun8i: dt: Enable A23 SMP support
ARM: dts: sun6i: Add cpu thermal zones to dtsi
ARM: dts: sun6i: Add cpu clock reference and operating points to dtsi
ARM: sunxi: DT: Add stdout-path property
...
Rename the socfpga_arria10_socdk board file to socfpga_arria10_socdk_sdmmc
as Arria 10 devkit cannot support SDMMC and QSPI at the same time. Thus
we will need to have 2 separate board files, one for SDMMC and one for
QSPI. We also add a new base board dtsi file, socfpga_arria10_socdk.dtsi
so that we use common peripherals for each flavor of the devkits.
Add the sdmmc node to the socfpga_arria10_socdk_sdmmc.dts board file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
With reworked device tree files for Compulab CM-A510 SoM and SBC-A510
base board, now add the correspoding board file to Makefile again.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Prior reworking Dove based Compulab CM-A510 device tree, remove it
from the compiled device tree files.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add DT file for Kizbox 2 board.
This board is based on Atmel's SAMA5D31 Cortex-A5 SoC.
Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add DT file for Kizbox mini board.
This board is based on Atmel's AT91SAM9G25 SoC.
Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The MK808C is an A20 based android stick, with 1G RAM, 8G NAND flash,
a RTL8723au wifi + bt combo chip, a USB host ports using USB-A receptacles,
a mini USB-B receptacle for USB OTG, mini HDMI and a TRS connector for AV.
This patch adds basic support for the device, more information can be found
here (http://linux-sunxi.org/MK808C).
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Jesurun Q5 has a black plastic casing with the approximate dimensions
of 100mm x 100mm x 24mm with rounded edges. In terms of hardware it
features an Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The
external connectors are: 2x USB-A female supporting USB2.0, 3.5mm female
jack for audio, HDMI female, SPDIF, RJ45 LAN and Power. In addition the
device has 1x red LED (hard wired to power) and an programmable green led.
On the board there is also an unpopulated IR receiver and the UART.
The devices is equipped with an AXP209 PMU.
For more details see: http://linux-sunxi.org/Jesurun_Q5
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orangepi mini is a development board using the Allwinner A20 SoC,
with 1G RAM, 2 microsd slots (use the top side one for booting), HDMI,
1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A ports,
ir receiver and a headphones jack.
Also see:
http://linux-sunxi.org/Xunlong_Orange_Pi_Minihttp://www.orangepi.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[maxime: Added /chosen/stdout-path]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orangepi is a development board using the Allwinner A20 SoC, with 1G RAM,
microsd slot, HDMI, 1Gbit ethernet, USB wifi, Micro USB (otg), sata, 4 USB A
ports, ir receiver and a headphones jack.
Also see:
http://linux-sunxi.org/Xunlong_Orange_Pihttp://www.orangepi.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[maxime: Added /chosen/stdout-path]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a Cubietech Cubieboard4 device tree and instruct make to build it. This
device tree has been derived from the sun9i-a80-optimus.dts as they are very
similar in design[1]. Notably, I2C3 is not used on Cubieboard4 and the LED/PWM
definitions will need to be updated in the future.
[1] http://dl.cubieboard.org/model/cc-a80/Hardware/CC-A80-HW-V1.1.pdf
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add support for Wexler TAB7200 tablet.
The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480),
capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot,
mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UTOO P66 is a 6" A13 tablet / lcd ereader. It features a 6" 480x800 ips
lcd screen, 512MB RAM & 4GB emmc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The auxtek-t004:
http://www.fasttech.com/products/1110/10004200/1318603-auxtek-t004-allwinner-a10s-single-core-android-ics
Is an Allwinner A10s based hdmi tv stick with with 512M RAM, 4G nand flash,
toc9002 (bcm43362) sdio wifi, 1 USB host ports using an USB-A receptacle and
a 2 micro-usb receptacles, one for power and one for USB OTG.
The sdio wifi appears to not have an oob irq hooked up, so we rely on sdio-irq
support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele I7 is a Allwinner A31 based Android TV box, with 1G RAM,
8GB NAND flash, a RTL8188etv wifi chip, 3 USB Host ports using
USB-A receptacles, a micro USB-B receptacle for USB OTG, HDMI out,
a TRS connector for A/V, SPDIF and IrDA.
This patch adds basic support for the device, more information can
be found here (http://linux-sunxi.org/Mele_I7).
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hans de Goede