We still need to set the IF_READY flag in ipv6_add_dev for the case
where all addresses (including the link-local) are deleted and then
recreated. In that case the IPv6 device too will be destroyed and
then recreated.
In order to prevent the original problem, we simply ensure that
the device is up before setting IF_READY.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per RFC2461, section 6.3.6, item #2, when no routers on the
matching list are known to be reachable or probably reachable we
do round robin on those available routes so that we make sure
to probe as many of them as possible to detect when one becomes
reachable faster.
Each routing table has a rwlock protecting the tree and the linked
list of routes at each leaf. The round robin code executes during
lookup and thus with the rwlock taken as a reader. A small local
spinlock tries to provide protection but this does not work at all
for two reasons:
1) The round-robin list manipulation, as coded, goes like this (with
read lock held):
walk routes finding head and tail
spin_lock();
rotate list using head and tail
spin_unlock();
While one thread is rotating the list, another thread can
end up with stale values of head and tail and then proceed
to corrupt the list when it gets the lock. This ends up causing
the OOPS in fib6_add() later onthat many people have been hitting.
2) All the other code paths that run with the rwlock held as
a reader do not expect the list to change on them, they
expect it to remain completely fixed while they hold the
lock in that way.
So, simply stated, it is impossible to implement this correctly using
a manipulation of the list without violating the rwlock locking
semantics.
Reimplement using a per-fib6_node round-robin pointer. This way we
don't need to manipulate the list at all, and since the round-robin
pointer can only ever point to real existing entries we don't need
to perform any locking on the changing of the round-robin pointer
itself. We only need to reset the round-robin pointer to NULL when
the entry it is pointing to is removed.
The idea is from Thomas Graf and it is very similar to how this
was implemented before the advanced router selection code when in.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a patch from Patrick McHardy.
The fib_rules netlink attribute policy introduced in 2.6.19 broke
userspace compatibilty. When specifying a rule with "from all"
or "to all", iproute adds a zero byte long netlink attribute,
but the policy requires all addresses to have a size equal to
sizeof(struct in_addr)/sizeof(struct in6_addr), resulting in a
validation error.
Check attribute length of FRA_SRC/FRA_DST in the generic framework
by letting the family specific rules implementation provide the
length of an address. Report an error if address length is non
zero but no address attribute is provided. Fix actual bug by
checking address length for non-zero instead of relying on
availability of attribute.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning up the warnings on gcc makes it emit warnings
about the placement of 'inline' in function declarations.
Here's everything that was under net/
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6_fl_socklist from listening socket is inadvertently shared
with new socket created for connection. This leads to a variety of
interesting, but fatal, bugs. For example, removing one of the
sockets may lead to the other socket's encountering a page fault
when the now freed list is referenced.
The fix is to not share the flow label list with the new socket.
Signed-off-by: Masayuki Nakagawa <nakagawa.msy@ncos.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
User supplied len < 0 can cause leak of kernel memory.
Use unsigned compare instead.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I came across this bug in http://bugzilla.kernel.org/show_bug.cgi?id=8155
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we add the IPv6 device at registration time we don't need
to set IF_READY in ipv6_add_dev anymore because we will always get
a NETDEV_UP event later on should the device ever become ready.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The individual fragments of a packet reassembled by conntrack have the
conntrack reference from the reassembled packet attached, but nfctinfo
is not copied. This leaves it initialized to 0, which unfortunately is
the value of IP_CT_ESTABLISHED.
The result is that all IPv6 fragments are tracked as ESTABLISHED,
allowing them to bypass a usual ruleset which accepts ESTABLISHED
packets early.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_netlink config option is named CONFIG_NF_CT_NETLINK,
but multiple files use CONFIG_IP_NF_CONNTRACK_NETLINK or
CONFIG_NF_CONNTRACK_NETLINK for ifdefs.
Fix this and reformat all CONFIG_NF_CT_NETLINK ifdefs to only use a line.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading /proc/net/anycast6 when there is no anycast address
on an interface results in an ever-increasing inet6_dev reference
count, as well as a reference to the netdevice you can't get rid of.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug in Linux IPv6 stack which caused anycast address
to be added to a device prior DAD has been completed. This led to
incorrect reference count which resulted in infinite wait for
unregister_netdevice completion on interface removal.
Signed-off-by: Michal Wrobel <xmxwx@asn.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more natural to manage prefix routes corresponding to address which is
being added manually.
With help from Masafumi Aramoto <aramoto@linux-ipv6.org>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This patch for adjust inet6_exit() to inverse sequence to inet6_init().
At ipv6_init, it first create proc_root/net/dev_snmp6 entry by call
ipv6_misc_proc_init(), then call addrconf_init() to create the corresponding
device entry at this directory, but at inet6_exit, ipv6_misc_proc_exit()
called first, then call addrconf_init().
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed to set fl_tunnel.fl6_src correctly in xfrm6_bundle_create().
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It isn't needed anymore, all of the users are gone, and all of the ctl_table
initializers have been converted to use explicit names of the fields they are
initializing.
[akpm@osdl.org: NTFS fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes xfrm6_tunnel register and deregister
interface to prepare for solving the conflict of device
tunnels with inter address family IPsec tunnel.
There is no device which conflicts with IPv4 over IPv6
IPsec tunnel.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sit use xfrm4_tunnel_register instead of
inet_add_protocol. It solves conflict of sit device with
inter address family IPsec tunnel.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tetsuo Handa <handat@pm.nttdata.co.jp> told me that connect(2) with TCPv6
socket almost always took a few minutes to return when we did not have any
ports available in the range of net.ipv4.ip_local_port_range.
The reason was that we used incorrect seed for calculating index of
hash when we check established sockets in __inet6_check_established().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regarding RFC3775, MH payload proto field should be IPPROTO_NONE. Otherwise
it must be discarded (and the receiver should send ICMP error).
We assume filter should drop such piggyback everytime to disallow slipping
through firewall rules, even the final receiver will discard it.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of depending on internally needed options and letting users
figure out what is needed, select them when needed:
- IP_NF_IPTABLES, IP_NF_ARPTABLES and IP6_NF_IPTABLES select
NETFILTER_XTABLES
- NETFILTER_XT_TARGET_CONNMARK, NETFILTER_XT_MATCH_CONNMARK and
IP_NF_TARGET_CLUSTERIP select NF_CONNTRACK_MARK
- NETFILTER_XT_MATCH_CONNBYTES selects NF_CT_ACCT
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_CT_STAT_INC assumes rcu_read_lock in nf_hook_slow disables
preemption as well, making it legal to use __get_cpu_var without
disabling preemption manually. The assumption is not correct anymore
with preemptable RCU, additionally we need to protect against softirqs
when not holding nf_conntrack_lock.
Add NF_CT_STAT_INC_ATOMIC macro, which disables local softirqs,
and use where necessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace preempt_{enable,disable} based RCU by proper use of the
RCU API and add missing rcu_read_lock/rcu_read_unlock calls in
all paths not obviously only used within packet process context
(nfnetlink_conntrack).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- rename nf_logging to nf_loggers since its an array of registered loggers
- rename nf_log_unregister_logger() to nf_log_unregister() to make it
symetrical to nf_log_register() and convert all users
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace appropriate pairs of "kmem_cache_alloc()" + "memset(0)" with the
corresponding "kmem_cache_zalloc()" call.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems to miss RO mode path by IPv6 over IPv4 IPsec tunnel patch
when it changed semantics to check the mode from
"xfrm[i]->props.mode != XFRM_MODE_TRANSPORT" to
"xfrm[i]->props.mode == XFRM_MODE_TUNNEL" before changing address.
It also makes two incline functions __xfrm6_bundle_addr_{remote,local}
are used by nobody.
This patch fixes it.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the next pointer from 'struct rt6_info.u' union,
and renames u.next to u.dst.rt6_next.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a prior patch, I introduced a sk_hash field (__sk_common.skc_hash) to let
tcp lookups use one cache line per unmatched entry instead of two.
We can also use sk_hash to speedup UDP part as well. We store in sk_hash the
hnum value, and use sk->sk_hash (same cache line than 'next' pointer),
instead of inet->num (different cache line)
Note : We still have a false sharing problem for SMP machines, because
sock_hold(sock) dirties the cache line containing the 'next' pointer. Not
counting the udp_hash_lock rwlock. (did someone mentioned RCU ? :) )
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehash table layout is currently this one :
First half of this table is used by sockets not in TIME_WAIT state
Second half of it is used by sockets in TIME_WAIT state.
This is non optimal because of for a given hash or socket, the two chain heads
are located in separate cache lines.
Moreover the locks of the second half are never used.
If instead of this halving, we use two list heads in inet_ehash_bucket instead
of only one, we probably can avoid one cache miss, and reduce ram usage,
particularly if sizeof(rwlock_t) is big (various CONFIG_DEBUG_SPINLOCK,
CONFIG_DEBUG_LOCK_ALLOC settings). So we still halves the table but we keep
together related chains to speedup lookups and socket state change.
In this patch I did not try to align struct inet_ehash_bucket, but a future
patch could try to make this structure have a convenient size (a power of two
or a multiple of L1_CACHE_SIZE).
I guess rwlock will just vanish as soon as RCU is plugged into ehash :) , so
maybe we dont need to scratch our heads to align the bucket...
Note : In case struct inet_ehash_bucket is not a power of two, we could
probably change alloc_large_system_hash() (in case it use __get_free_pages())
to free the unused space. It currently allocates a big zone, but the last
quarter of it could be freed. Again, this should be a temporary 'problem'.
Patch tested on ipv4 tcp only, but should be OK for IPV6 and DCCP.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ip6t_standard/ip6t_error_target/ip6t_error definitions to ip6_tables.h
instead of defining them in each table individually.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces match for Mobility Header (MH) described by Mobile IPv6
specification (RFC3775). User can specify the MH type or its range to be
matched.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: Yasuyuki Kozakai <kozakai@linux-ipv6.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the x_tables functions directly to make it better visible which
parts are shared between ip_tables and ip6_tables.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary if() constructs before assignment.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was no real useful information from the unregister_netdevice() return
code, the only error occurred in a situation that was a driver bug. So
change it to a void function.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checksum default defines for mobility header(MH) which
goes through raw socket. As the result kernel's behavior is
to handle MH checksum as default.
This patch also removes verifying inbound MH checksum at
mip6_mh_filter() since it did not consider user specified
checksum offset and was redundant check with raw socket code.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
add_grhead() allocates memory with GFP_ATOMIC and in at least two places skb
from it passed to skb_put() without checking.
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the patch to support IPv4 over IPv6 IPsec.
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu