On fsg_unbind the common->fsg pointer was not NULLed if the
unbound fsg_dev instance was the current one. As an effect,
the incorrect pointer was preserved in all further operations
which caused do_set_interface to reference an invalid region.
This commit fixes this by raising an exception in fsg_bind
which will change the common->fsg pointer. This also requires
an wait queue so that the thread in fsg_bind can wait till the
worker thread handles the exception.
This commit removes also a config and new_config fields of
fsg_common as they are no longer needed since fsg can be
used to determine whether function is active or not.
Moreover, this commit removes possible race condition where
the fsg field was modified in both the worker thread and
form various other contexts. This is fixed by replacing
prev_fsg with new_fsg. At this point, fsg is assigned only
in worker thread.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The full speed descriptors were copied to the usb_function structure
in the fsg_bind_config function before call to the usb_ep_autoconfig.
The usb_ep_autoconfig was called in fsg_bind using the original
descriptors. In effect copied descriptors were not updated.
This patch changes the copy full speed descriptors after the call to
usb_op_autoconfig is performed. This way, copied full speed
descriptors have updated values.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Dries Van Puymbroeck <Dries.VanPuymbroeck@dekimo.com>
Tested-by: Dries Van Puymbroeck <Dries.VanPuymbroeck@dekimo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting MUSB Burst Mode 3 automatically enables support for
lower burst modes (BURST4, BURST8, BURST16 or bursts of unspecified
length). There is no need to set these burst modes based on the
packet size. Also enable the burst mode for both mode1 and mode0.
This is a fix for buggy hardware - having the lower burst modes
enabled can potentially cause lockups of the DMA engine used in
OMAP2/3/4 chips.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new ulpi code defines fallback stubs for the Blackfin arch, but does
so incorrectly leading to a build failure:
drivers/usb/musb/musb_core.c:227: error: 'musb_ulpi_read' undeclared here (not in a function)
drivers/usb/musb/musb_core.c:228: error: 'musb_ulpi_write' undeclared here (not in a function)
Tweak the fallback stubs so that they do work as intended.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attempt to build MUSB driver with CONFIG_PM=y (e.g. in the OTG mode) on DaVinci
results in these link errors:
drivers/built-in.o: In function `musb_restore_context':
led-triggers.c:(.text+0x714d8): undefined reference to
`musb_platform_restore_context'
drivers/built-in.o: In function `musb_save_context':
led-triggers.c:(.text+0x71788): undefined reference to
`musb_platform_save_context'
This turned out to be caused by commit 9957dd97ec
(usb: musb: Fix compile error for omaps for musb_hdrc). Revert it, taking into
account the rename of CONFIG_ARCH_OMAP34XX into CONFIG_ARCH_OMAP3 (which that
commit fixed in a completely inappropriate way) and the recent addition of
OMAP4 support.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 1c25fda4a0 (usb: musb: handle irqs in the
order dictated by programming guide) forgot to get rid of the old 'STAGE0_MASK'
filter for calling musb_stage0_irq(), so now disconnect and suspend interrupts
are effectively ignored...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1403) is a partial reversion of an earlier change
(commit 5f677f1d45 "USB: fix remote
wakeup settings during system sleep"). After hearing from a user, I
realized that remote wakeup should be enabled during system sleep
whenever userspace allows it, and not only if a driver requests it
too.
Indeed, there could be a device with no driver, that does nothing but
generate a wakeup request when the user presses a button. Such a
device should be allowed to do its job.
The problem fixed by the earlier patch -- device generating a wakeup
request for no reason, causing system suspend to abort -- was also
addressed by a later patch ("USB: don't enable remote wakeup by
default", accepted but not yet merged into mainline). The device
won't be able to generate the bogus wakeup requests because it will be
disabled for remote wakeup by default. Hence this reversion will not
re-introduce any old problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CRC should be calculated for Ethernet frame, not for whole recievede EEM data.
This bug shows rarely, because in many times len == skb->len.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds missing kfree(data) before return -ENODEV.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found that sleep is called inside atomic context created by
lock_printer_io spinlock in several functions. It's used in process
context only and some functions sleep inside its critical section. As
this is not allowed for spinlocks, switch it to mutex.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Craig W. Nadler <craig@nadler.us>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found that isp1362_sw_reset tries to take a isp1362_hcd->lock,
but it is already held in isp1362_hc_stop. Avoid that by introducing
__isp1362_sw_reset which doesn't take the lock and call it from
isp1362_hc_stop. isp1362_sw_reset is then as simple as lock --
__isp1362_sw_reset -- unlock.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects a problem with the merge of a previous
patch to add the CONTEC identifier.
I believe the merge problem occurred with the commit:
dee5658b48
Originally I submitted a patch and then they asked me to order the IDs
and resubmit, so did I. But unfortunately in the end somehow both
patches were merged.
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1401) fixes a bug in usb_sg_init() that can cause an
invalid pointer dereference. An inner loop reuses some local variables
in an unsafe manner, so new variables are introduced.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Gadget disconnect must be called before unbinding to avoid races.
The change fixes an oops on g_ether module unregistering.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As a part of aligning the ISR code for MUSB with the specs, the
ISR code was re-written.
See Commit 1c25fda4a0 (usb: musb: handle
irqs in the order dictated by programming guide)
With this the suspend interrupt came accidently under CONFIG_USB_MUSB_HDRC_HCD.
The fix brings suspend interrupt handling outside
CONFIG_USB_MUSB_HDRC_HCD.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the change by 749da5f82f,
The change in the status when the USB device is connected is wrong.
Therefore, the device is not recognized.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Paul Mundt" <lethal@linux-sh.org>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 6c12db90f1 introduced a bug for
control transfers. The patch was supposed to change when the link TRBs at
the end of each ring segment were given to the hardware. If a transfer
descriptor (TD) ended just before the link TRB, the code wouldn't give
back the link TRB to the hardware; instead it would be given back in
prepare_ring() just before the next TD was enqueued at the top of the
ring.
Unfortunately, the code relied on checking the chain bit of the TRB to
determine whether the TD ended just before the link TRB. It assumed that
the ring enqueuing code would call prepare_ring() before enqueuing the
next TD. However, control transfers are made of multiple TDs, and
prepare_ring() is only called once before enqueuing two or three TDs.
If the first or second TD of the control transfer ended just before the
link TRB, then the code in inc_enq() would not move the enqueue pointer
past the link TRB, and the link TRB would get overwritten. This would
cause the xHCI driver to start writing to memory past the ring segment,
and eventually the system would crash or hang.
The fix is to add a flag to inc_enq() that says whether the caller will
enqueue more TDs before calling prepare_ring(). If the chain bit is
cleared (meaning this is the last TRB in a TD), and the caller will not
enqueue more TDs, then we defer giving back the link TRB.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During __gfs_do_config() some invalid pointers may be left
in usb_configuration::interfaces array from previous calls
to the __gfs_do_config() for the same configuration. This
will always happen if an user space function which has
a fewer then the last user space function registers itself.
Composite's set_config() function that a pointer after the
last interface in usb_configuration::interface is NULL
unless the array is full.
This patch makes the __gfs_do_config() make sure that if the
usb_configuration::interface is not full then a pointer
after the last interface is NULL.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call put_tty_driver() in cleanup function, to fix Oops when trying to open
gadget serial char device after module unload.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No longer set low_latency flag as it causes this warning backtrace:
WARNING: at kernel/mutex.c:207 __mutex_lock_slowpath+0x6c/0x288()
Fix associated locking and wakeups.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: Maulik Mankad <x0082077@ti.com>
Cc: stable <stable@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Make intc messages consistent via pr_fmt.
sh: make sure static declaration on ms7724se
sh: make sure static declaration on mach-migor
sh: make sure static declaration on mach-ecovec24
sh: make sure static declaration on mach-ap325rxa
clocksource: sh_cmt: compute mult and shift before registration
clocksource: sh_tmu: compute mult and shift before registration
sh: PIO disabling for x3proto and urquell.
sh: mach-sdk7786: conditionally disable PIO support.
sh: support for platforms without PIO.
usb: r8a66597-hcd pio to mmio accessor conversion.
usb: gadget: r8a66597-udc pio to mmio accessor conversion.
usb: gadget: m66592-udc pio to mmio accessor conversion.
sh: add romImage MMCIF boot for sh7724 and Ecovec V2
sh: add boot code to MMCIF driver header
sh: prepare MMCIF driver header file
sh: allow romImage data between head.S and the zero page
sh: Add support MMCIF for ecovec
sh: remove duplicated #include
input: serio: disable i8042 for non-cayman sh platforms.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: unbind all interfaces before rebinding them
USB: serial: digi_acceleport: Eliminate a NULL pointer dereference
usb: fix ehci_hcd build failure when both generic-OF and xilinx is selected
USB: cdc-acm: fix resource reclaim in error path of acm_probe
USB: ftdi_sio: fix DTR/RTS line modes
USB: s3c-hsotg: Ensure FIFOs are fully flushed after layout
USB: s3c-hsotg: SoftDisconnect minimum 3ms
USB: s3c-hsotg: Ensure TX FIFO addresses setup when initialising FIFOs
USB: s3c_hsotg: define USB_GADGET_DUALSPEED in Kconfig
USB: s3c: Enable soft disconnect during initialization
USB: xhci: Print NEC firmware version.
USB: xhci: Wait for host to start running.
USB: xhci: Wait for controller to be ready after reset.
USB: isp1362: fix inw warning on Blackfin systems
USB: mos7840: fix null-pointer dereference
This patch (as1387) fixes a bug introduced during the changeover to
the runtime PM framework. When a driver doesn't support resume or
reset-resume, and consequently its interfaces need to be unbound and
rebound, we have to unbind all the interfaces before trying to rebind
any of them. Otherwise the driver's probe method for one interface
could try to claim a different interface and fail, because that other
interface hasn't been unbound yet.
This fixes Bugzilla #15788. The symptom is that some USB sound cards
don't work after hibernation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: François Valenduc <francois.valenduc@tvcablenet.be>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If port is NULL, then the call to dev_err will dereference a value that is
a small offset from NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the driver to allow both CONFIG_USB_EHCI_HCD_PPC_OF and
CONFIG_USB_ECHI_HCD_XILINX to be selected.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: John Linn <john.linn@xilinx.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes resource reclaim in error path of acm_probe:
1. In the case of "out of memory (read urbs usb_alloc_urb)\n")", there
is no need to call acm_read_buffers_free(acm) here. Fix it by goto
alloc_fail6 instead of alloc_fail7.
2. In the case of "out of memory (write urbs usb_alloc_urb)",
usb_alloc_urb may fail in any iteration of the for loop. Current
implementation does not properly free allocated snd->urb. Fix it by
goto alloc_fail8 instead of alloc_fail7.
3. In the case of device_create_file(&intf->dev,&dev_attr_iCountryCodeRelDate)
fail, acm->country_codes is kfreed. As a result, device_remove_file
for dev_attr_wCountryCodes will not be executed in acm_disconnect.
Fix it by calling device_remove_file for dev_attr_wCountryCodes
before goto skip_countries.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call set_mctrl() and clear_mctrl() according to the flow control mode
selected. This makes serial communication for FT232 connected devices
work when CRTSCTS is not set.
This fixes a regression introduced by 4175f3e31 ("tty_port: If we are
opened non blocking we still need to raise the carrier"). This patch
calls the low-level driver's dtr_rts() function which consequently sets
TIOCM_DTR | TIOCM_RTS. A later call to set_termios() without CRTSCTS in
cflags, however, does not reset these bits, and so data is not actually
sent out on the serial wire.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the design guide, if the FIFO layout is changed, then the
FIFOs must be flushed to ensure all FIFO pointers are correct.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The shortest period SoftDisconnect can be asserted for is 3 milliseconds
according to the V210 datasheet, so ensure that we add an msleep() to
the registration code to enforce this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some versions of the S3C HS OtG block startup with overlapping TX FIFO
information, so change the fifo_init code to ensure that known values
are set into the FIFO registers at initialisation/reset time.
This also ensures that the FIFO RAM pointers are in a known state
before use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The s3c_hsotg driver sets usb_gadget->is_dualspeed to 1, yet it doesn't define
USB_GADGET_DUALSPEED in Kconfig. This triggers a NULL pointer dereference in
the composite driver (which is fixed in another patch).
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enable soft disconnect bit the OTG core during initialization. Without this,
the host sees that a gadget is connected and tries to enumerate. The
soft disconnect should be enabled until the USB gadget driver is
registered with this otg driver.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The NEC xHCI host controller firmware version can be found by putting a
vendor-specific command on the command ring and extracting the BCD
encoded-version out of the vendor-specific event TRB.
The firmware version debug line in dmesg will look like:
xhci_hcd 0000:05:00.0: NEC firmware version 30.21
(NEC merged with Renesas Technologies and became Renesas Electronics on
April 1, 2010. I have their OK to merge this vendor-specific code.)
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Satoshi Otani <satoshi.otani.xm@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the run bit is set in the xHCI command register, it may take a few
microseconds for the host to start running. We cannot ring any doorbells
until the host is actually running, so wait until the status register says
the host is running.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Shinya Saito <shinya.saito.sx@renesas.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After software resets an xHCI host controller, it must wait for the
"Controller Not Ready" (CNR) bit in the status register to be cleared.
Software is not supposed to ring any doorbells or write to any registers
except the status register until this bit is cleared.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin code is incorrectly casting the argument to inw() to a pointer.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda-intel - fix wallclk variable update and condition
ALSA: asihpi - Fix uninitialized variable
ALSA: hda: Use LPIB for ASUS M2V
usb/gadget: Replace the old USB audio FU definitions in f_audio.c
ASoC: MX31ads sound support should depend on MACH_MX31ADS_WM1133_EV1
ASoC: Add missing Kconfig entry for Phytec boards
ALSA: usb-audio: export UAC2 clock selectors as mixer controls
ALSA: usb-audio: clean up find_audio_control_unit()
ALSA: usb-audio: add UAC2 sepecific Feature Unit controls
ALSA: usb-audio: unify constants from specification
ALSA: usb-audio: parse clock topology of UAC2 devices
ALSA: usb-audio: fix selector unit string index accessor
include/linux/usb/audio-v2.h: add more UAC2 details
ALSA: usb-audio: support partially write-protected UAC2 controls
ALSA: usb-audio: UAC2: clean up parsing of bmaControls
ALSA: hda: Use LPIB for another mainboard
ALSA: hda: Use mb31 quirk for an iMac model
ALSA: hda: Use LPIB for an ASUS device
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix driver to use new location of of_node pointer (introduced by commit
use new location of of_node pointer (introduced by commit
61c7a080a5a061c976988fd4b844dfb468dda255; of: Always use 'struct
device.of_node' to get device node pointer)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reported-by: John Linn <john.linn@xilinx.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: linux-usb@vger.kernel.org
CC: devicetree-discuss@lists.ozlabs.org
r8a66597-hcd is erroneously using PIO routines on MMIO registers, which
presently blows up for any platform that elects to either override or do
away with PIO routines. This managed to work for the common cases since
the PIO routines were simply wrapped to their MMIO counterparts. This
switches over to using the MMIO routines directly, and enables us to kill
off a lot of superfluous casting in the process.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
r8a66597-udc is erroneously using PIO routines on MMIO registers, which
presently blows up for any platform that elects to either override or do
away with PIO routines. This managed to work for the common cases since
the PIO routines were simply wrapped to their MMIO counterparts. This
switches over to using the MMIO routines directly, and enables us to kill
off a lot of superfluous casting in the process.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
m66592-udc is erroneously using PIO routines on MMIO registers, which
presently blows up for any platform that elects to either override or do
away with PIO routines. This managed to work for the common cases since
the PIO routines were simply wrapped to their MMIO counterparts. This
switches over to using the MMIO routines directly, and enables us to kill
off a lot of superfluous casting in the process.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The USB audio FU definitions were renewed by the commit
65f25da44b
ALSA: usb-audio: unify constants from specification
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of using own implementation which potentialy has bugs involve
hex_to_bin() function. It requires to have hex_to_bin() implementation
introduced by starter patch in series.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Nazarewicz