When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Documentation/CodingStyle recommends to use label names which say
what the goto does or why the goto exists.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, the status register FI2C_SR is checked immediately after
a STOP condition is issued in case of the deferred STOP condition.
It takes typically 5-10 usec until the corresponding bits in the
register are set, so the error check for "stop condition was not
completed" is very likely to be false positive.
Add wait code to relax the status register check.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, the adapter is set to the master mode at the first use.
Since then, it is kept in the slave mode, so unexpected glitch
signals on the I2C lines may cause the adapter into insane state.
Setting it to the master mode along with initialization solves the
problem.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Akio Noda <noda.akio@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If clk_prepare_enable() fails, clk_disable_unprepare() is called in
the failure path, where the enable_count is still zero, so it hits
WARN_ON(core->enable_count == 0) in the clk_core_disable().
To fix this, make the clock setting more linear in the probe function
so that it can exploit "goto err" in case of error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc. This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Masahiro Yamada