On mips and parisc:
drivers/bluetooth/btwilink.c: In function 'ti_st_open':
drivers/bluetooth/btwilink.c:174:21: warning: overflow in implicit constant conversion [-Woverflow]
hst->reg_status = -EINPROGRESS;
drivers/nfc/nfcwilink.c: In function 'nfcwilink_open':
drivers/nfc/nfcwilink.c:396:31: warning: overflow in implicit constant conversion [-Woverflow]
drv->st_register_cb_status = -EINPROGRESS;
There are actually two issues:
1. Whether "char" is signed or unsigned depends on the architecture.
As the completion callback data is used to pass a (negative) error
code, it should always be signed.
2. EINPROGRESS is 150 on mips, 245 on parisc.
Hence -EINPROGRESS doesn't fit in a signed 8-bit number.
Change the callback status from "char" to "int" to fix these.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When pn533_recv_frame is called from within abort_command
context the current dev->cmd is not guaranteed to be set.
Additionally on receiving an error status we can omit frame
checking and simply schedule the workqueue.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We need to reset the poll modulation list before calling
nfc_targets_found because otherwise userspace could run
before the modulation list is cleared and then get a "Cannot
activate target while polling" error upon calling activate_target.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When a command gets aborted the pn533 core does not need any RX
frames that may be received until a new frame is sent.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Correctly call nfc_set_parent_dev before nfc_register_device.
Otherwise the driver will OOPS when being removed.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The requested irq needs to be freed when removing the driver,
otherwise a following driver load fails to request the irq.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NCI provides possible way to run loopback testing has done over HCI.
For us it offers many advantages:
- It simplifies the code: No more need for a vendor_cmds structure
- Loopback over HCI may not be supported in future st-nci firmware
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to NCI specification, destination type and destination
specific parameters shall uniquely identify a single destination
for the Logical Connection.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ST21NFCA_ESE_HOST_ID is already defined in st21nfca.h.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ST_NCI_HCI_HOST_ID_ESE is already having an equivalent in se.c
(ST_NCI_ESE_HOST_ID).
Remove and replace where relevant.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When st_nci_spi_acpi_request_resources() gets called we
already know that the entries in ->acpi_match_table have
matched ACPI ID of the device.
In addition spi_device pointer cannot be NULL in any case
(otherwise SPI core would not call ->probe() for the driver
in the first place).
Drop the two useless checks from the driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When st_nci_i2c_acpi_request_resources() gets called we already
know that the entries in ->acpi_match_table have matched ACPI ID
of the device.
In addition I2C client pointer cannot be NULL in any case
(otherwise I2C core would not call ->probe() for the driver in
the first place).
Drop the two useless checks from the driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When st21nfca_hci_i2c_acpi_request_resources() gets called we
already know that the entries in ->acpi_match_table have matched
ACPI ID of the device.
In addition I2C client pointer cannot be NULL in any case
(otherwise I2C core would not call ->probe() for the driver in
the first place).
Drop the two useless checks from the driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
An APDU_READER_GATE pipe is not expected on a UICC. Be more
explicit so that an other secure element form factor (SD card)
does not prompt this message.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
An APDU_READER_GATE pipe is not expected on a UICC. Be more
explicit so that an other secure element form factor (SD card)
does not prompt this message.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When they're present, set is_ese_present and set is_uicc_present
to the value describe in their package description.
So far is_ese_present and is_uicc_present was set to true if their
property was present.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When they're present, set is_ese_present and set is_uicc_present
to the value describe in their package description.
So far is_ese_present and is_uicc_present was set to true if their
property was present.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since
commit 10cf4899f8 ("gpiolib: tighten up ACPI legacy gpio lookups")
If _DSD properties are available in an ACPI node, we are not
allowed to fallback to _CRS data to retrieve gpio properties.
This was causing us to fail if uicc-present and/or ese-present
are defined.
To be consistent with devicetree change ST_NCI_GPIO_NAME_RESET
content to reset so that acpi_find_gpio in drivers/gpio/gpiolib.c
will look for reset-gpios. In the mean time the ACPI table needs
to be fixed as follow:
Device (NFC1)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "SMO2100") // _HID: Hardware ID
Name (_CID, "SMO2100") // _CID: Compatible ID
Name (_DDN, "SMO NFC") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (SBUF, ResourceTemplate ()
{
I2cSerialBus (0x0008, ControllerInitiated, 400000,
AddressingMode7Bit, "\\_SB.I2C7",
0x00, ResourceConsumer, ,)
GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0001
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0002,
}
})
Name (_DSD, Package (0x02)
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x03)
{
Package (0x02) { "uicc-present", 1 },
Package (0x02) { "ese-present", 1 },
Package (0x02) { "enable-gpios", Package(0x04) { ^NFC1, 1, 0, 0} },
}
})
Return (SBUF) /* \_SB_.I2C7.NFC1._CRS.SBUF */
}
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
}
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since
commit 10cf4899f8 ("gpiolib: tighten up ACPI legacy gpio lookups")
If _DSD properties are available in an ACPI node, we are not
allowed to fallback to _CRS data to retrieve gpio properties.
This was causing us to fail if uicc-present and/or ese-present
are defined.
To be consistent with devicetree change ST_NCI_GPIO_NAME_RESET
content to reset so that acpi_find_gpio in drivers/gpio/gpiolib.c
will look for reset-gpios. In the mean time the ACPI table needs
to be fixed as follow (Tested on Minnowboard Max):
Device (NFC1)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "SMO2101") // _HID: Hardware ID
Name (_CID, "SMO2101") // _CID: Compatible ID
Name (_DDN, "SMO NFC") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (SBUF, ResourceTemplate ()
{
SpiSerialBus (0, PolarityLow, FourWireMode, 8,
ControllerInitiated, 4000000, ClockPolarityLow,
ClockPhaseFirst, "\\_SB.SPI1",
0x00, ResourceConsumer, ,)
GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0001
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0002,
}
})
Name (_DSD, Package (0x02)
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x03)
{
Package (0x02) { "uicc-present", 1 },
Package (0x02) { "ese-present", 1 },
Package (0x02) { "reset-gpios", Package(0x04) { ^NFC1, 1, 0, 0} },
}
})
Return (SBUF) /* \_SB_.SPI1.NFC1._CRS.SBUF */
}
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
}
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since
commit 10cf4899f8 ("gpiolib: tighten up ACPI legacy gpio lookups")
If _DSD properties are available in an ACPI node, we are not
allowed to fallback to _CRS data to retrieve gpio properties.
This was causing us to fail if uicc-present and/or ese-present
are defined.
To be consistent with devicetree change ST_NCI_GPIO_NAME_RESET
content to reset so that acpi_find_gpio in drivers/gpio/gpiolib.c
will look for reset-gpios. In the mean time the ACPI table needs
to be fixed as follow:
Device (NFC1)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "SMO2101") // _HID: Hardware ID
Name (_CID, "SMO2101") // _CID: Compatible ID
Name (_DDN, "SMO NFC") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (SBUF, ResourceTemplate ()
{
I2cSerialBus (0x0008, ControllerInitiated, 400000,
AddressingMode7Bit, "\\_SB.I2C7",
0x00, ResourceConsumer, ,)
GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0001
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0002,
}
})
Name (_DSD, Package (0x02)
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x03)
{
Package (0x02) { "uicc-present", 1 },
Package (0x02) { "ese-present", 1 },
Package (0x02) { "reset-gpios", Package(0x04) { ^NFC1, 1, 0, 0} },
}
})
Return (SBUF) /* \_SB_.I2C7.NFC1._CRS.SBUF */
}
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
}
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix static checker warning:
drivers/nfc/st21nfca/i2c.c:530 st21nfca_hci_i2c_acpi_request_resources()
error: 'gpiod_ena' dereferencing possible ERR_PTR()
Fix so that if no enable gpio can be retrieved an -ENODEV is returned.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: dfa8070d7f ("nfc: st21nfca: Add support for acpi probing for i2c device.")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds the I2C phy interface for the pn533 driver.
This way the driver can be used to interact with I2C
connected pn532 devices.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver now has all core stuff isolated in one file, and all
the hardware link specifics in another. Writing a pn533 driver
on top of another hardware link is now just a matter of adding a
new file for that new hardware specifics.
The first user of this separation will be the i2c based pn532
driver that reuses pn533 core implementation on top of an i2c
layer.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A deadlock can occur when the NFC raw socket is closed while
the driver is processing a command.
Following is the call graph of the affected situation:
send data via raw_sock:
-------------
rawsock_tx_work
sock_hold => socket refcnt++
nfc_data_exchange => cb = rawsock_data_exchange_complete
ops->im_transceive = pn533_transceive => arg->cb = db
= rawsock_data_exchange_complete
pn533_send_data_async => cb = pn533_data_exchange_complete
__pn533_send_async => cmd->complete_cb = cb
= pn533_data_exchange_complete
if_ops->send_frame_async
response:
--------
pn533_recv_response
queue_work(priv->wq, &priv->cmd_complete_work)
pn533_wq_cmd_complete
pn533_send_async_complete
cmd->complete_cb() = pn533_data_exchange_complete()
arg->cb() = rawsock_data_exchange_complete()
sock_put => socket refcnt-- => If the corresponding
socket gets closed in the meantime socket
will be destructed
sk_free
__sk_free
sk->sk_destruct = rawsock_destruct
nfc_deactivate_target
ops->deactivate_target = pn533_deactivate_target
pn533_send_cmd_sync
pn533_send_cmd_async
__pn533_send_async
list_add_tail(&cmd->queue,&dev->cmd_queue)
=> add to command list because
a command is currently
processed
wait_for_completion
=> the workqueue thread waits
here because it is the one
processing the commands
=> deadlock
To fix the deadlock pn533_deactivate_target is changed to
issue the PN533_CMD_IN_RELEASE command in async mode. This
way nothing blocks and the release command is executed after
the current command.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently it is not possible to only poll for passive targets
with the pn533 driver. To change this ATR_REQ is only sent when
NFC_PROTO_NFC_DEP is explicitly requested in poll_protocols.
As most implementations (e.g. neard) poll for all protocols
that are reported to be supported by the adapter, this should
not have much of an effect on current implementations.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
Originally I only wanted to drop the unneeded inclusion of
<linux/i2c.h>, but then noticed that struct
microread_nfc_platform_data isn't actually used, and
MICROREAD_DRIVER_NAME is redefined in the only file where it is used,
so we can get rid of the header file and dead code altogether.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When pn544_hci_i2c_acpi_request_resources() gets called we
already know that the entries in ->acpi_match_table have
matched ACPI ID of the device.
In addition I2C client pointer cannot be NULL in any case
(otherwise I2C core would not call ->probe() for the driver
in the first place).
Drop the two useless checks from the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
gpio irq is already configured by the core i2c layers
when reaching the probe function
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
gpio irq is already configured by the core i2c layers
when reaching the probe function.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In microread_i2c_phy, irq field is never used.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is cleaner to check if the i2c_client irq is not configured
properly before allocating any data.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The core st21nca module is useless without the I2C access module.
So hide NFC_ST21NFCA and select it automatically if either
NFC_ST21NFCA_I2C is selected.
This avoids presenting NFC_ST21NFCA when NFC_ST21NFCA_I2C can't be
selected.
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The core st-nci module is useless without either the I2C or the
SPI access module. So hide NFC_ST_NCI and select it automatically
if either NFC_ST_NCI_I2C or NFC_ST_NCI_SPI is selected.
This avoids presenting NFC_ST_NCI when neither NFC_ST_NCI_I2C nor
NFC_ST_NCI_SPI can be selected.
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for acpi probing.
SMO2101 is used for st21nfcb
SMO2102 is used for st21nfcc
It has been tested with the following acpi node on Minnowboard:
Note: Remove uicc-present or ese-present Package if one them is not
supported.
Device (NFC1)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "SMO2101") // _HID: Hardware ID
Name (_CID, "SMO2101") // _CID: Compatible ID
Name (_DDN, "SMO NFC") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Name (_DSD, Package (0x02)
{
/* Device Properties for _DSD */
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package (0x02)
{
Package (0x02) { "uicc-present", 1 },
Package (0x02) { "ese-present", 1 }
}
})
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (SBUF, ResourceTemplate ()
{
I2cSerialBus (0x0008, ControllerInitiated, 400000,
AddressingMode7Bit, "\\_SB.I2C7",
0x00, ResourceConsumer, ,)
GpioInt (Edge, ActiveHigh, ExclusiveAndWake, PullNone, 0x0000,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0001
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO2", 0x00, ResourceConsumer, ,)
{ // Pin list
0x0002,
}
})
Return (SBUF) /* \_SB_.I2C7.NFC1._CRS.SBUF */
}
Method (_STA, 0, NotSerialized) // _STA: Status
{
Return (0x0F)
}
}
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add macro definition for each gpio string for an easier code
maintenance.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add macro definition for each gpio string for an easier code
maintenance.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Group device table at the same place in order to make the code
easier to read and parse.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Group device table at the same place in order to make the code
easier to read and parse.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Geert Uytterhoeven