While load_balance() masks the source CPUs against active_mask, it had
a hole against the destination CPU. Ensure the destination CPU is also
part of the 'domain-mask & active-mask' set.
Reported-by: Levin, Alexander (Sasha Levin) <alexander.levin@verizon.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 77d1dfda0e ("sched/topology, cpuset: Avoid spurious/wrong domain rebuilds")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The trivial wake_affine_idle() implementation is very good for a
number of workloads, but it comes apart at the moment there are no
idle CPUs left, IOW. the overloaded case.
hackbench:
NO_WA_WEIGHT WA_WEIGHT
hackbench-20 : 7.362717561 seconds 6.450509391 seconds
(win)
netperf:
NO_WA_WEIGHT WA_WEIGHT
TCP_SENDFILE-1 : Avg: 54524.6 Avg: 52224.3
TCP_SENDFILE-10 : Avg: 48185.2 Avg: 46504.3
TCP_SENDFILE-20 : Avg: 29031.2 Avg: 28610.3
TCP_SENDFILE-40 : Avg: 9819.72 Avg: 9253.12
TCP_SENDFILE-80 : Avg: 5355.3 Avg: 4687.4
TCP_STREAM-1 : Avg: 41448.3 Avg: 42254
TCP_STREAM-10 : Avg: 24123.2 Avg: 25847.9
TCP_STREAM-20 : Avg: 15834.5 Avg: 18374.4
TCP_STREAM-40 : Avg: 5583.91 Avg: 5599.57
TCP_STREAM-80 : Avg: 2329.66 Avg: 2726.41
TCP_RR-1 : Avg: 80473.5 Avg: 82638.8
TCP_RR-10 : Avg: 72660.5 Avg: 73265.1
TCP_RR-20 : Avg: 52607.1 Avg: 52634.5
TCP_RR-40 : Avg: 57199.2 Avg: 56302.3
TCP_RR-80 : Avg: 25330.3 Avg: 26867.9
UDP_RR-1 : Avg: 108266 Avg: 107844
UDP_RR-10 : Avg: 95480 Avg: 95245.2
UDP_RR-20 : Avg: 68770.8 Avg: 68673.7
UDP_RR-40 : Avg: 76231 Avg: 75419.1
UDP_RR-80 : Avg: 34578.3 Avg: 35639.1
UDP_STREAM-1 : Avg: 64684.3 Avg: 66606
UDP_STREAM-10 : Avg: 52701.2 Avg: 52959.5
UDP_STREAM-20 : Avg: 30376.4 Avg: 29704
UDP_STREAM-40 : Avg: 15685.8 Avg: 15266.5
UDP_STREAM-80 : Avg: 8415.13 Avg: 7388.97
(wins and losses)
sysbench:
NO_WA_WEIGHT WA_WEIGHT
sysbench-mysql-2 : 2135.17 per sec. 2142.51 per sec.
sysbench-mysql-5 : 4809.68 per sec. 4800.19 per sec.
sysbench-mysql-10 : 9158.59 per sec. 9157.05 per sec.
sysbench-mysql-20 : 14570.70 per sec. 14543.55 per sec.
sysbench-mysql-40 : 22130.56 per sec. 22184.82 per sec.
sysbench-mysql-80 : 20995.56 per sec. 21904.18 per sec.
sysbench-psql-2 : 1679.58 per sec. 1705.06 per sec.
sysbench-psql-5 : 3797.69 per sec. 3879.93 per sec.
sysbench-psql-10 : 7253.22 per sec. 7258.06 per sec.
sysbench-psql-20 : 11166.75 per sec. 11220.00 per sec.
sysbench-psql-40 : 17277.28 per sec. 17359.78 per sec.
sysbench-psql-80 : 17112.44 per sec. 17221.16 per sec.
(increase on the top end)
tbench:
NO_WA_WEIGHT
Throughput 685.211 MB/sec 2 clients 2 procs max_latency=0.123 ms
Throughput 1596.64 MB/sec 5 clients 5 procs max_latency=0.119 ms
Throughput 2985.47 MB/sec 10 clients 10 procs max_latency=0.262 ms
Throughput 4521.15 MB/sec 20 clients 20 procs max_latency=0.506 ms
Throughput 9438.1 MB/sec 40 clients 40 procs max_latency=2.052 ms
Throughput 8210.5 MB/sec 80 clients 80 procs max_latency=8.310 ms
WA_WEIGHT
Throughput 697.292 MB/sec 2 clients 2 procs max_latency=0.127 ms
Throughput 1596.48 MB/sec 5 clients 5 procs max_latency=0.080 ms
Throughput 2975.22 MB/sec 10 clients 10 procs max_latency=0.254 ms
Throughput 4575.14 MB/sec 20 clients 20 procs max_latency=0.502 ms
Throughput 9468.65 MB/sec 40 clients 40 procs max_latency=2.069 ms
Throughput 8631.73 MB/sec 80 clients 80 procs max_latency=8.605 ms
(increase on the top end)
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Eric reported a sysbench regression against commit:
3fed382b46 ("sched/numa: Implement NUMA node level wake_affine()")
Similarly, Rik was looking at the NAS-lu.C benchmark, which regressed
against his v3.10 enterprise kernel.
PRE (current tip/master):
ivb-ep sysbench:
2: [30 secs] transactions: 64110 (2136.94 per sec.)
5: [30 secs] transactions: 143644 (4787.99 per sec.)
10: [30 secs] transactions: 274298 (9142.93 per sec.)
20: [30 secs] transactions: 418683 (13955.45 per sec.)
40: [30 secs] transactions: 320731 (10690.15 per sec.)
80: [30 secs] transactions: 355096 (11834.28 per sec.)
hsw-ex NAS:
OMP_PROC_BIND/lu.C.x_threads_144_run_1.log: Time in seconds = 18.01
OMP_PROC_BIND/lu.C.x_threads_144_run_2.log: Time in seconds = 17.89
OMP_PROC_BIND/lu.C.x_threads_144_run_3.log: Time in seconds = 17.93
lu.C.x_threads_144_run_1.log: Time in seconds = 434.68
lu.C.x_threads_144_run_2.log: Time in seconds = 405.36
lu.C.x_threads_144_run_3.log: Time in seconds = 433.83
POST (+patch):
ivb-ep sysbench:
2: [30 secs] transactions: 64494 (2149.75 per sec.)
5: [30 secs] transactions: 145114 (4836.99 per sec.)
10: [30 secs] transactions: 278311 (9276.69 per sec.)
20: [30 secs] transactions: 437169 (14571.60 per sec.)
40: [30 secs] transactions: 669837 (22326.73 per sec.)
80: [30 secs] transactions: 631739 (21055.88 per sec.)
hsw-ex NAS:
lu.C.x_threads_144_run_1.log: Time in seconds = 23.36
lu.C.x_threads_144_run_2.log: Time in seconds = 22.96
lu.C.x_threads_144_run_3.log: Time in seconds = 22.52
This patch takes out all the shiny wake_affine() stuff and goes back to
utter basics. Between the two CPUs involved with the wakeup (the CPU
doing the wakeup and the CPU we ran on previously) pick the CPU we can
run on _now_.
This restores much of the regressions against the older kernels,
but leaves some ground in the overloaded case. The default-enabled
WA_WEIGHT (which will be introduced in the next patch) is an attempt
to address the overloaded situation.
Reported-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jinpuwang@gmail.com
Cc: vcaputo@pengaru.com
Fixes: 3fed382b46 ("sched/numa: Implement NUMA node level wake_affine()")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull scheduler fixes from Ingo Molnar:
"Three CPU hotplug related fixes and a debugging improvement"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Add debugfs knob for "sched_debug"
sched/core: WARN() when migrating to an offline CPU
sched/fair: Plug hole between hotplug and active_load_balance()
sched/fair: Avoid newidle balance for !active CPUs
The load balancer applies cpu_active_mask to whatever sched_domains it
finds, however in the case of active_balance there is a hole between
setting rq->{active_balance,push_cpu} and running the stop_machine
work doing the actual migration.
The @push_cpu can go offline in this window, which would result in us
moving a task onto a dead cpu, which is a fairly bad thing.
Double check the active mask before the stop work does the migration.
CPU0 CPU1
<SoftIRQ>
stop_machine(takedown_cpu)
load_balance() cpu_stopper_thread()
... work = multi_cpu_stop
stop_one_cpu_nowait( /* wait for CPU0 */
.func = active_load_balance_cpu_stop
);
</SoftIRQ>
cpu_stopper_thread()
work = multi_cpu_stop
/* sync with CPU1 */
take_cpu_down()
<idle>
play_dead();
work = active_load_balance_cpu_stop
set_task_cpu(p, CPU1); /* oops!! */
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170907150614.044460912@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On CPU hot unplug, when parking the last kthread we'll try and
schedule into idle to kill the CPU. This last schedule can (and does)
trigger newidle balance because at this point the sched domains are
still up because of commit:
77d1dfda0e ("sched/topology, cpuset: Avoid spurious/wrong domain rebuilds")
Obviously pulling tasks to an already offline CPU is a bad idea, and
all balancing operations _should_ be subject to cpu_active_mask, make
it so.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: 77d1dfda0e ("sched/topology, cpuset: Avoid spurious/wrong domain rebuilds")
Link: http://lkml.kernel.org/r/20170907150613.994135806@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Work around kernel-doc warning ('*' in Sphinx doc means "emphasis"):
../kernel/sched/fair.c:7584: WARNING: Inline emphasis start-string without end-string.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/f18b30f9-6251-6d86-9d44-16501e386891@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Chris Wilson reported that the SMT balance rules got the +1 on the
wrong side, resulting in a bias towards the current LLC; which the
load-balancer would then try and undo.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Fixes: 90001d67be ("sched/fair: Fix wake_affine() for !NUMA_BALANCING")
Link: http://lkml.kernel.org/r/20170906105131.gqjmaextmn3u6tj2@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Drop the P-state selection algorithm based on a PID controller
from intel_pstate and make it use the same P-state selection
method (based on the CPU load) for all types of systems in the
active mode (Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to
take cross-CPU utilization updates into account and modify the
schedutil governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the
mediatek cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points
(OPP) DT bindings and update its whitelist of supported systems
(Viresh Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen,
Finley Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to
make it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number
of items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on
x86 in a more straightforward way and to use %pOF instead of
full_name (Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor
issues (Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mAiV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This time (again) cpufreq gets the majority of changes which mostly
are driver updates (including a major consolidation of intel_pstate),
some schedutil governor modifications and core cleanups.
There also are some changes in the system suspend area, mostly related
to diagnostics and debug messages plus some renames of things related
to suspend-to-idle. One major change here is that suspend-to-idle is
now going to be preferred over S3 on systems where the ACPI tables
indicate to do so and provide requsite support (the Low Power Idle S0
_DSM in particular). The system sleep documentation and the tools
related to it are updated too.
The rest is a few cpuidle changes (nothing major), devfreq updates,
generic power domains (genpd) framework updates and a few assorted
modifications elsewhere.
Specifics:
- Drop the P-state selection algorithm based on a PID controller from
intel_pstate and make it use the same P-state selection method
(based on the CPU load) for all types of systems in the active mode
(Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to take
cross-CPU utilization updates into account and modify the schedutil
governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the mediatek
cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points (OPP)
DT bindings and update its whitelist of supported systems (Viresh
Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen, Finley
Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to make
it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number of
items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on x86
in a more straightforward way and to use %pOF instead of full_name
(Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor issues
(Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava)"
* tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (87 commits)
cpuidle: Make drivers initialize polling state
cpuidle: Move polling state initialization code to separate file
cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
PM: docs: Delete the obsolete states.txt document
PM: docs: Describe high-level PM strategies and sleep states
PM / devfreq: Fix memory leak when fail to register device
PM / devfreq: Add dependency on PM_OPP
PM / devfreq: Move private devfreq_update_stats() into devfreq
PM / devfreq: Convert to using %pOF instead of full_name
PM / AVS: rockchip-io: add io selectors and supplies for RV1108
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpuidle: Convert to using %pOF instead of full_name
cpufreq: Convert to using %pOF instead of full_name
PM / Domains: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
...
In commit:
3fed382b46 ("sched/numa: Implement NUMA node level wake_affine()")
Rik changed wake_affine to consider NUMA information when balancing
between LLC domains.
There are a number of problems here which this patch tries to address:
- LLC < NODE; in this case we'd use the wrong information to balance
- !NUMA_BALANCING: in this case, the new code doesn't do any
balancing at all
- re-computes the NUMA data for every wakeup, this can mean iterating
up to 64 CPUs for every wakeup.
- default affine wakeups inside a cache
We address these by saving the load/capacity values for each
sched_domain during regular load-balance and using these values in
wake_affine_llc(). The obvious down-side to using cached values is
that they can be too old and poorly reflect reality.
But this way we can use LLC wide information and thus not rely on
assuming LLC matches NODE. We also don't rely on NUMA_BALANCING nor do
we have to aggegate two nodes (or even cache domains) worth of CPUs
for each wakeup.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Fixes: 3fed382b46 ("sched/numa: Implement NUMA node level wake_affine()")
[ Minor readability improvements. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Running 80 tasks in the same group, or as threads of the same process,
results in the memory getting scanned 80x as fast as it would be if a
single task was using the memory.
This really hurts some workloads.
Scale the scan period by the number of tasks in the numa group, and
the shared / private ratio, so the average rate at which memory in
the group is scanned corresponds roughly to the rate at which a single
task would scan its memory.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jhladky@redhat.com
Cc: lvenanci@redhat.com
Link: http://lkml.kernel.org/r/20170731192847.23050-3-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The comment above update_task_scan_period() says the scan period should
be increased (scanning slows down) if the majority of memory accesses
are on the local node, or if the majority of the page accesses are
shared with other tasks.
However, with the current code, all a high ratio of shared accesses
does is slow down the rate at which scanning is made faster.
This patch changes things so either lots of shared accesses or
lots of local accesses will slow down scanning, and numa scanning
is sped up only when there are lots of private faults on remote
memory pages.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jhladky@redhat.com
Cc: lvenanci@redhat.com
Link: http://lkml.kernel.org/r/20170731192847.23050-2-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The running state is a subset of runnable state which means that running
can't be set if runnable (weight) is cleared. There are corner cases
where the current sched_entity has been already dequeued but cfs_rq->curr
has not been updated yet and still points to the dequeued sched_entity.
If ___update_load_avg() is called at that time, weight will be 0 and running
will be set which is not possible.
This case happens during pick_next_task_fair() when a cfs_rq becomes idles.
The current sched_entity has been dequeued so se->on_rq is cleared and
cfs_rq->weight is null. But cfs_rq->curr still points to se (it will be
cleared when picking the idle thread). Because the cfs_rq becomes idle,
idle_balance() is called and ends up to call update_blocked_averages()
with these wrong running and runnable states.
Add a test in ___update_load_avg() to correct the running state in this case.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten.Rasmussen@arm.com
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dietmar.eggemann@arm.com
Link: http://lkml.kernel.org/r/1498885573-18984-1-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
update_freq is always true and there is no need to pass it to
update_cfs_rq_load_avg(). Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/r/2d28d295f3f591ede7e931462bce1bda5aaa4896.1495603536.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rearrange pick_next_task_fair() a bit to avoid checking
cfs_rq->nr_running twice for the case where FAIR_GROUP_SCHED is enabled
and the previous task doesn't belong to the fair class.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/r/000903ab3df3350943d3271c53615893a230dc95.1495603536.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
weighted_cpuload() uses the cpu number passed to it get pointer to the
runqueue. Almost all callers of weighted_cpuload() already have the rq
pointer with them and can send that directly to weighted_cpuload(). In
some cases the callers actually get the CPU number by doing cpu_of(rq).
It would be simpler to pass rq to weighted_cpuload().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/r/b7720627e0576dc29b4ba3f9b6edbc913bb4f684.1495603536.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For SMP systems, update_load_avg() calls the cpufreq update util
handlers only for the top level cfs_rq (i.e. rq->cfs).
But that is not the case for UP systems. update_load_avg() calls util
handler for any cfs_rq for which it is called. This would result in way
too many calls from the scheduler to the cpufreq governors when
CONFIG_FAIR_GROUP_SCHED is enabled.
Reduce the frequency of these calls by copying the behavior from the SMP
case, i.e. Only call util handlers for the top level cfs_rq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Fixes: 536bd00cdb ("sched/fair: Fix !CONFIG_SMP kernel cpufreq governor breakage")
Link: http://lkml.kernel.org/r/6abf69a2107525885b616a2c1ec03d9c0946171c.1495603536.git.viresh.kumar@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
With Android UI and benchmarks the latency of cpufreq response to
certain scheduling events can become very critical. Currently, callbacks
into cpufreq governors are only made from the scheduler if the target
CPU of the event is the same as the current CPU. This means there are
certain situations where a target CPU may not run the cpufreq governor
for some time.
One testcase to show this behavior is where a task starts running on
CPU0, then a new task is also spawned on CPU0 by a task on CPU1. If the
system is configured such that the new tasks should receive maximum
demand initially, this should result in CPU0 increasing frequency
immediately. But because of the above mentioned limitation though, this
does not occur.
This patch updates the scheduler core to call the cpufreq callbacks for
remote CPUs as well.
The schedutil, ondemand and conservative governors are updated to
process cpufreq utilization update hooks called for remote CPUs where
the remote CPU is managed by the cpufreq policy of the local CPU.
The intel_pstate driver is updated to always reject remote callbacks.
This is tested with couple of usecases (Android: hackbench, recentfling,
galleryfling, vellamo, Ubuntu: hackbench) on ARM hikey board (64 bit
octa-core, single policy). Only galleryfling showed minor improvements,
while others didn't had much deviation.
The reason being that this patch only targets a corner case, where
following are required to be true to improve performance and that
doesn't happen too often with these tests:
- Task is migrated to another CPU.
- The task has high demand, and should take the target CPU to higher
OPPs.
- And the target CPU doesn't call into the cpufreq governor until the
next tick.
Based on initial work from Steve Muckle.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If load_balance() fails to migrate any tasks because all tasks were
affined, load_balance() removes the source CPU from consideration and
attempts to redo and balance among the new subset of CPUs.
There is a bug in this code path where the algorithm considers all active
CPUs in the system (minus the source that was just masked out). This is
not valid for two reasons: some active CPUs may not be in the current
scheduling domain and one of the active CPUs is dst_cpu. These CPUs should
not be considered, as we cannot pull load from them.
Instead of failing out of load_balance(), we may end up redoing the search
with no valid CPUs and incorrectly concluding the domain is balanced.
Additionally, if the group_imbalance flag was just set, it may also be
incorrectly unset, thus the flag will not be seen by other CPUs in future
load_balance() runs as that algorithm intends.
Fix the check by removing CPUs not in the current domain and the dst_cpu
from considertation, thus limiting the evaluation to valid remaining CPUs
from which load might be migrated.
Co-authored-by: Austin Christ <austinwc@codeaurora.org>
Co-authored-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Austin Christ <austinwc@codeaurora.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Timur Tabi <timur@codeaurora.org>
Link: http://lkml.kernel.org/r/1496863138-11322-2-git-send-email-jhugo@codeaurora.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Stephen reported the following build warning in UP:
kernel/sched/fair.c:2657:9: warning: 'struct sched_domain' declared inside
parameter list
^
/home/sfr/next/next/kernel/sched/fair.c:2657:9: warning: its scope is only this
definition or declaration, which is probably not what you want
Hide the numa_wake_affine() inline stub on UP builds to get rid of it.
Fixes: 3fed382b46 ("sched/numa: Implement NUMA node level wake_affine()")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
The effective_load() function was only used by the NUMA balancing
code, and not by the regular load balancing code. Now that the
NUMA balancing code no longer uses it either, get rid of it.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jhladky@redhat.com
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20170623165530.22514-5-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since select_idle_sibling() can place a task anywhere on a socket,
comparing loads between individual CPU cores makes no real sense
for deciding whether to do an affine wakeup across sockets, either.
Instead, compare the load between the sockets in a similar way the
load balancer and the numa balancing code do.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jhladky@redhat.com
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20170623165530.22514-4-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Then 'this_cpu' and 'prev_cpu' are in the same socket, select_idle_sibling()
will do its thing regardless of the return value of wake_affine().
Just return true and don't look at all the other things.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jhladky@redhat.com
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20170623165530.22514-3-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Several tests in the NAS benchmark seem to run a lot slower with
NUMA balancing enabled, than with NUMA balancing disabled. The
slower run time corresponds with increased idle time.
Overriding the final test of migrate_degrades_locality (but still
doing the other NUMA tests first) seems to improve performance
of those benchmarks.
Reported-by: Jirka Hladky <jhladky@redhat.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20170623165530.22514-2-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Although idle load balancing obviously only concerns idle CPUs, it can
be a disturbance on a busy nohz_full CPU. Indeed a CPU can only get rid
of an idle load balancing duty once a tick fires while it runs a task
and this can take a while on a nohz_full CPU.
We could fix that and escape the idle load balancing duty from the very
idle exit path but that would bring unecessary overhead. Lets just not
bother and leave that job to housekeeping CPUs (those outside nohz_full
range). The nohz_full CPUs simply don't want any disturbance.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1497838322-10913-4-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Conflicts:
kernel/sched/Makefile
Pick up the waitqueue related renames - it didn't get much feedback,
so it appears to be uncontroversial. Famous last words? ;-)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If we set a next or last buddy for a se that is not on_rq, we will
end up taking a NULL pointer dereference in wakeup_preempt_entity
via pick_next_task_fair.
Detect when we would be about to do that, throw a warning and
then refuse to actually set it.
This has been suggested at least twice:
https://marc.info/?l=linux-kernel&m=146651668921468&w=2https://lkml.org/lkml/2016/6/16/663
I recently had to debug a problem with these (we hadn't backported
Konstantin's patches in this area) and this would have saved a lot
of time/pain.
Just do it.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Cc: Ben Segall <bsegall@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170510201139.16236-1-dja@axtens.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
'schedstats' kernel parameter should be set to enable/disable, so
correct the printk hint saying that it should be set to 'enable'
rather than 'enabled' to enable scheduler tracepoints.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1496995229-31245-1-git-send-email-marcin.nowakowski@imgtec.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Hackbench recently suffered a bunch of pain, first by commit:
4c77b18cf8 ("sched/fair: Make select_idle_cpu() more aggressive")
and then by commit:
c743f0a5c5 ("sched/fair, cpumask: Export for_each_cpu_wrap()")
which fixed a bug in the initial for_each_cpu_wrap() implementation
that made select_idle_cpu() even more expensive. The bug was that it
would skip over CPUs when bits were consequtive in the bitmask.
This however gave me an idea to fix select_idle_cpu(); where the old
scheme was a cliff-edge throttle on idle scanning, this introduces a
more gradual approach. Instead of stopping to scan entirely, we limit
how many CPUs we scan.
Initial benchmarks show that it mostly recovers hackbench while not
hurting anything else, except Mason's schbench, but not as bad as the
old thing.
It also appears to recover the tbench high-end, which also suffered like
hackbench.
Tested-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Cc: kitsunyan <kitsunyan@inbox.ru>
Cc: linux-kernel@vger.kernel.org
Cc: lvenanci@redhat.com
Cc: riel@redhat.com
Cc: xiaolong.ye@intel.com
Link: http://lkml.kernel.org/r/20170517105350.hk5m4h4jb6dfr65a@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A customer has reported a soft-lockup when running an intensive
memory stress test, where the trace on multiple CPU's looks like this:
RIP: 0010:[<ffffffff810c53fe>]
[<ffffffff810c53fe>] native_queued_spin_lock_slowpath+0x10e/0x190
...
Call Trace:
[<ffffffff81182d07>] queued_spin_lock_slowpath+0x7/0xa
[<ffffffff811bc331>] change_protection_range+0x3b1/0x930
[<ffffffff811d4be8>] change_prot_numa+0x18/0x30
[<ffffffff810adefe>] task_numa_work+0x1fe/0x310
[<ffffffff81098322>] task_work_run+0x72/0x90
Further investigation showed that the lock contention here is pmd_lock().
The task_numa_work() function makes sure that only one thread is let to perform
the work in a single scan period (via cmpxchg), but if there's a thread with
mmap_sem locked for writing for several periods, multiple threads in
task_numa_work() can build up a convoy waiting for mmap_sem for read and then
all get unblocked at once.
This patch changes the down_read() to the trylock version, which prevents the
build up. For a workload experiencing mmap_sem contention, it's probably better
to postpone the NUMA balancing work anyway. This seems to have fixed the soft
lockups involving pmd_lock(), which is in line with the convoy theory.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170515131316.21909-1-vbabka@suse.cz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, rq->leaf_cfs_rq_list is a traversal ordered list of all
live cfs_rqs which have ever been active on the CPU; unfortunately,
this makes update_blocked_averages() O(# total cgroups) which isn't
scalable at all.
This shows up as a small CPU consumption and scheduling latency
increase in the load balancing path in systems with CPU controller
enabled across most cgroups. In an edge case where temporary cgroups
were leaking, this caused the kernel to consume good several tens of
percents of CPU cycles running update_blocked_averages(), each run
taking multiple millisecs.
This patch fixes the issue by taking empty and fully decayed cfs_rqs
off the rq->leaf_cfs_rq_list.
Signed-off-by: Tejun Heo <tj@kernel.org>
[ Added cfs_rq_is_decayed() ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Chris Mason <clm@fb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170426004350.GB3222@wtj.duckdns.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to allow leaf_cfs_rq_list to remove entries switch the
bandwidth hotplug code over to the task_groups list.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170504133122.a6qjlj3hlblbjxux@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There's a discrepancy in naming between the sched_domain and
sched_group cpumask accessor. Since we're doing changes, fix it.
$ git grep sched_group_cpus | wc -l
28
$ git grep sched_domain_span | wc -l
38
Suggests changing sched_group_cpus() into sched_group_span():
for i in `git grep -l sched_group_cpus`
do
sed -ie 's/sched_group_cpus/sched_group_span/g' $i
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since sched_group_mask() is now an independent cpumask (it no longer
masks sched_group_cpus()), rename the thing.
Suggested-by: Lauro Ramos Venancio <lvenanci@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While writing the comments, it occurred to me that:
sg_cpus & sg_mask == sg_mask
at least conceptually; the !overlap case sets the all 1s mask. If we
correct that we can simplify things and directly use sg_mask.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
More users for for_each_cpu_wrap() have appeared. Promote the construct
to generic cpumask interface.
The implementation is slightly modified to reduce arguments.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Lauro Ramos Venancio <lvenanci@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: lwang@redhat.com
Link: http://lkml.kernel.org/r/20170414122005.o35me2h5nowqkxbv@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In the current implementation of load/util_avg, we assume that the
ongoing time segment has fully elapsed, and util/load_sum is divided
by LOAD_AVG_MAX, even if part of the time segment still remains to
run. As a consequence, this remaining part is considered as idle time
and generates unexpected variations of util_avg of a busy CPU in the
range [1002..1024[ whereas util_avg should stay at 1023.
In order to keep the metric stable, we should not consider the ongoing
time segment when computing load/util_avg but only the segments that
have already fully elapsed. But to not consider the current time
segment adds unwanted latency in the load/util_avg responsivness
especially when the time is scaled instead of the contribution.
Instead of waiting for the current time segment to have fully elapsed
before accounting it in load/util_avg, we can already account the
elapsed part but change the range used to compute load/util_avg
accordingly.
At the very beginning of a new time segment, the past segments have
been decayed and the max value is LOAD_AVG_MAX*y. At the very end of
the current time segment, the max value becomes:
LOAD_AVG_MAX*y + 1024(us) (== LOAD_AVG_MAX)
In fact, the max value is:
LOAD_AVG_MAX*y + sa->period_contrib
at any time in the time segment.
Taking advantage of the fact that:
LOAD_AVG_MAX*y == LOAD_AVG_MAX-1024
the range becomes [0..LOAD_AVG_MAX-1024+sa->period_contrib].
As the elapsed part is already accounted in load/util_sum, we update
the max value according to the current position in the time segment
instead of removing its contribution.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Morten.Rasmussen@arm.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bsegall@google.com
Cc: dietmar.eggemann@arm.com
Cc: pjt@google.com
Cc: yuyang.du@intel.com
Link: http://lkml.kernel.org/r/1493188076-2767-1-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that we have a tool to generate the PELT constants in C form,
use its output as a separate header.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We truncate (and loose) the lower 10 bits of runtime in
___update_load_avg(), this means there's a consistent bias to
under-account tasks. This is esp. significant for small tasks.
Cure this by only forwarding last_update_time to the point we've
actually accounted for, leaving the remainder for the next time.
Reported-by: Morten Rasmussen <morten.rasmussen@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Historically our periods (or p) argument in PELT denoted the number of
full periods (what is now d2). However recent patches have changed
this to the total decay (previously p+1), leading to a confusing
discrepancy between comments and code.
Try and clarify things by making periods (in code) and p (in comments)
be the same thing (again).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Paul noticed that in the (periods >= LOAD_AVG_MAX_N) case in
__accumulate_sum(), the returned contribution value (LOAD_AVG_MAX) is
incorrect.
This is because at this point, the decay_load() on the old state --
the first step in accumulate_sum() -- will not have resulted in 0, and
will therefore result in a sum larger than the maximum value of our
series. Obviously broken.
Note that:
decay_load(LOAD_AVG_MAX, LOAD_AVG_MAX_N) =
1 (345 / 32)
47742 * - ^ = ~27
2
Not to mention that any further contribution from the d3 segment (our
new period) would also push it over the maximum.
Solve this by noting that we can write our c2 term:
p
c2 = 1024 \Sum y^n
n=1
In terms of our maximum value:
inf inf p
max = 1024 \Sum y^n = 1024 ( \Sum y^n + \Sum y^n + y^0 )
n=0 n=p+1 n=1
Further note that:
inf inf inf
( \Sum y^n ) y^p = \Sum y^(n+p) = \Sum y^n
n=0 n=0 n=p
Combined that gives us:
p
c2 = 1024 \Sum y^n
n=1
inf inf
= 1024 ( \Sum y^n - \Sum y^n - y^0 )
n=0 n=p+1
= max - (max y^(p+1)) - 1024
Further simplify things by dealing with p=0 early on.
Reported-by: Paul Turner <pjt@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yuyang Du <yuyang.du@intel.com>
Cc: linux-kernel@vger.kernel.org
Fixes: a481db34b9 ("sched/fair: Optimize ___update_sched_avg()")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The main PELT function ___update_load_avg(), which implements the
accumulation and progression of the geometric average series, is
implemented along the following lines for the scenario where the time
delta spans all 3 possible sections (see figure below):
1. add the remainder of the last incomplete period
2. decay old sum
3. accumulate new sum in full periods since last_update_time
4. accumulate the current incomplete period
5. update averages
Or:
d1 d2 d3
^ ^ ^
| | |
|<->|<----------------->|<--->|
... |---x---|------| ... |------|-----x (now)
load_sum' = (load_sum + weight * scale * d1) * y^(p+1) + (1,2)
p
weight * scale * 1024 * \Sum y^n + (3)
n=1
weight * scale * d3 * y^0 (4)
load_avg' = load_sum' / LOAD_AVG_MAX (5)
Where:
d1 - is the delta part completing the remainder of the last
incomplete period,
d2 - is the delta part spannind complete periods, and
d3 - is the delta part starting the current incomplete period.
We can simplify the code in two steps; the first step is to separate
the first term into new and old parts like:
(load_sum + weight * scale * d1) * y^(p+1) = load_sum * y^(p+1) +
weight * scale * d1 * y^(p+1)
Once we've done that, its easy to see that all new terms carry the
common factors:
weight * scale
If we factor those out, we arrive at the form:
load_sum' = load_sum * y^(p+1) +
weight * scale * (d1 * y^(p+1) +
p
1024 * \Sum y^n +
n=1
d3 * y^0)
Which results in a simpler, smaller and faster implementation.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bsegall@google.com
Cc: dietmar.eggemann@arm.com
Cc: matt@codeblueprint.co.uk
Cc: morten.rasmussen@arm.com
Cc: pjt@google.com
Cc: umgwanakikbuti@gmail.com
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/1486935863-25251-3-git-send-email-yuyang.du@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The __update_load_avg() function is an __always_inline because its
used with constant propagation to generate different variants of the
code without having to duplicate it (which would be prone to bugs).
Explicitly instantiate the 3 variants.
Note that most of this is called from rather hot paths, so reducing
branches is good.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the child domain prefers tasks to go siblings, the local group could
end up pulling tasks to itself even if the local group is almost equally
loaded as the source group.
Lets assume a 4 core,smt==2 machine running 5 thread ebizzy workload.
Everytime, local group has capacity and source group has atleast 2 threads,
local group tries to pull the task. This causes the threads to constantly
move between different cores. This is even more profound if the cores have
more threads, like in Power 8, smt 8 mode.
Fix this by only allowing local group to pull a task, if the source group
has more number of tasks than the local group.
Here are the relevant perf stat numbers of a 22 core,smt 8 Power 8 machine.
Without patch:
Performance counter stats for 'ebizzy -t 22 -S 100' (5 runs):
1,440 context-switches # 0.001 K/sec ( +- 1.26% )
366 cpu-migrations # 0.000 K/sec ( +- 5.58% )
3,933 page-faults # 0.002 K/sec ( +- 11.08% )
Performance counter stats for 'ebizzy -t 48 -S 100' (5 runs):
6,287 context-switches # 0.001 K/sec ( +- 3.65% )
3,776 cpu-migrations # 0.001 K/sec ( +- 4.84% )
5,702 page-faults # 0.001 K/sec ( +- 9.36% )
Performance counter stats for 'ebizzy -t 96 -S 100' (5 runs):
8,776 context-switches # 0.001 K/sec ( +- 0.73% )
2,790 cpu-migrations # 0.000 K/sec ( +- 0.98% )
10,540 page-faults # 0.001 K/sec ( +- 3.12% )
With patch:
Performance counter stats for 'ebizzy -t 22 -S 100' (5 runs):
1,133 context-switches # 0.001 K/sec ( +- 4.72% )
123 cpu-migrations # 0.000 K/sec ( +- 3.42% )
3,858 page-faults # 0.002 K/sec ( +- 8.52% )
Performance counter stats for 'ebizzy -t 48 -S 100' (5 runs):
2,169 context-switches # 0.000 K/sec ( +- 6.19% )
189 cpu-migrations # 0.000 K/sec ( +- 12.75% )
5,917 page-faults # 0.001 K/sec ( +- 8.09% )
Performance counter stats for 'ebizzy -t 96 -S 100' (5 runs):
5,333 context-switches # 0.001 K/sec ( +- 5.91% )
506 cpu-migrations # 0.000 K/sec ( +- 3.35% )
10,792 page-faults # 0.001 K/sec ( +- 7.75% )
Which show that in these workloads CPU migrations get reduced significantly.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Link: http://lkml.kernel.org/r/1490205470-10249-1-git-send-email-srikar@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch fix spelling typos found in
Documentation/output/xml/driver-api/basics.xml.
It is because the xml file was generated from comments in source,
so I had to fix the comments.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A regression of the FTQ noise has been reported by Ying Huang,
on the following hardware:
8 threads Intel(R) Core(TM)i7-4770 CPU @ 3.40GHz with 8G memory
... which was caused by this commit:
commit 4e5160766f ("sched/fair: Propagate asynchrous detach")
The only part of the patch that can increase the noise is the update
of blocked load of group entity in update_blocked_averages().
We can optimize this call and skip the update of group entity if its load
and utilization are already null and there is no pending propagation of load
in the task group.
This optimization partly restores the noise score. A more agressive
optimization has been tried but has shown worse score.
Reported-by: ying.huang@linux.intel.com
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dietmar.eggemann@arm.com
Cc: ying.huang@intel.com
Fixes: 4e5160766f ("sched/fair: Propagate asynchrous detach")
Link: http://lkml.kernel.org/r/1489758442-2877-1-git-send-email-vincent.guittot@linaro.org
[ Fixed typos, improved layout. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra