Remove dev_err() messages after platform_get_irq*() failures.
platform_get_irq() already prints an error.
Generated by: scripts/coccinelle/api/platform_get_irq.cocci
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Link: https://lore.kernel.org/r/20220303125054.3574-1-hanyihao@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix following coccicheck warning:
./drivers/spi/spi-cadence-xspi.c:490:1-23: WARNING: Function
for_each_child_of_node should have of_node_put() before return
Early exits from for_each_child_of_node should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211015033919.5915-1-wanjiabing@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes Smatch static checker warning.
CDNS_XSPI_CMD_REG_5 is used in ACMD mode and currently
only STIG mode is enabled which doesn't use CDNS_XSPI_CMD_REG_5
and hence everything was working in STIG mode.
Since plan is to use same function cdns_xspi_trigger_command()
in ACMD mode, increasing size of the array passed to it.
Fixes: a16cc80776 ("spi: cadence: add support for Cadence XSPI controller")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/linux-spi/20210930134231.GA14363@kili/
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Link: https://lore.kernel.org/r/1633336704-22735-1-git-send-email-pthombar@cadence.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Parshuram Thombare <pthombar@cadence.com>
Link: https://lore.kernel.org/r/20210928130712.990474-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver for Cadence's XSPI controller.
It supports 3 work modes.
1. ACMD (auto command) work mode
ACMD name is because it uses auto command engine in the controller.
It further has 2 modes PIO and CDMA (command DMA).
The CDMA work mode is dedicated for high-performance application
where very low software overhead is required. In this mode the
Command Engine is programmed by the series of linked descriptors
stored in system memory. These descriptors provide commands to execute
and store status information for finished commands.
The PIO mode work mode is dedicated for single operation where
constructing a linked list of descriptors would require too
much effort.
2. STIG (Software Triggered Instruction Generator) work mode
In STIG mode, controller sends low-level instructions to memory.
Each instruction is 128-bit width. There is special instruction
DataSequence which carries information about data phase.
Driver uses Slave DMA interface to transfer data as only this
interface can be used in STIG work mode.
3. Direct work mode
This work mode allows sending data without invoking any command through
the slave interface.
Currently only STIG work mode is enabled, remaining work modes will
be added later.
Signed-off-by: Konrad Kociolek <konrad@cadence.com>
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1632038734-23999-1-git-send-email-pthombar@cadence.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Yihao Han