This allows drivers to pass 802.3 frames to mac80211, with some restrictions:
- the skb must be passed with a valid sta
- fast-rx needs to be active for the sta
- monitor mode needs to be disabled
mac80211 will tell the driver when it is safe to enable rx decap offload for
a particular station.
In order to implement support, a driver must:
- call ieee80211_hw_set(hw, SUPPORTS_RX_DECAP_OFFLOAD)
- implement ops->sta_set_decap_offload
- mark 802.3 frames with RX_FLAG_8023
If it doesn't want to enable offload for some vif types, it can mask out
IEEE80211_OFFLOAD_DECAP_ENABLED in vif->offload_flags from within the
.add_interface or .update_vif_offload driver ops
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-6-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current API (which lets the driver turn on/off per vif directly) has a
number of limitations:
- it does not deal with AP_VLAN
- conditions for enabling (no tkip, no monitor) are only checked at
add_interface time
- no way to indicate 4-addr support
In order to address this, store offload flags in struct ieee80211_vif
(easy to extend for decap offload later). mac80211 initially sets the enable
flag, but gives the driver a chance to modify it before its settings are
applied. In addition to the .add_interface op, a .update_vif_offload op is
introduced, which can be used for runtime changes.
If a driver can't disable encap offload at runtime, or if it has some extra
limitations, it can simply override the flags within those ops.
Support for encap offload with 4-address mode interfaces can be enabled
by setting a flag from .add_interface or .update_vif_offload.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-6-nbd@nbd.name
[resolved conflict with commit aa2092a9ba ("ath11k: add raw mode and
software crypto support")]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben Greear has repeatedly reported in the past (for a few years
probably) that this triggers repeatedly in certain scenarios.
Make this a macro so that each callsite can trigger the warning
only once - that will still give us an idea of what's going on
and what paths can reach it, but avoids being too noisy.
Link: https://lore.kernel.org/r/20200730155212.06fd3a95dbfb.I0b16829aabfaf5f642bce401502a29d16e2dd444@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement drv_set_tid_config api to allow TID specific
configuration and drv_reset_tid_config api to reset peer
specific TID configuration. This per-TID onfiguration
will be applied for all the connected stations when MAC is NULL.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-7-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
-----BEGIN PGP SIGNATURE-----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=JQOx
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates, notably:
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduce a new driver callback drv_sta_set_txpwr. This API will
copy the transmit power value passed from user space and call the driver
callback to set the tx power for the station.
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are several scenarios in which mac80211 can call drv_wake_tx_queue
after ieee80211_restart_hw has been called and has not yet completed.
Driver private structs are considered uninitialized until mac80211 has
uploaded the vifs, stations and keys again, so using private tx queue
data during that time is not safe.
The driver can also not rely on drv_reconfig_complete to figure out when
it is safe to accept drv_wake_tx_queue calls again, because it is only
called after all tx queues are woken again.
To fix this, bail out early in drv_wake_tx_queue if local->in_reconfig
is set.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may want to track further the CSA beacons, for example
to compensate for buggy APs that change the beacon count or quiet
mode during CSA flow.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case we receive a beacon without CSA IE while we are in
the middle of channel switch - abort the operation.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we reworked ieee80211_return_txq() so it assumes that the caller
takes care of logging, we need another function that can be called without
holding any locks. Introduce ieee80211_schedule_txq() which serves this
purpose.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds an API to mac80211 to handle scheduling of TXQs. The interface
between driver and mac80211 for TXQ handling is changed by adding two new
functions: ieee80211_next_txq(), which will return the next TXQ to schedule
in the current round-robin rotation, and ieee80211_return_txq(), which the
driver uses to indicate that it has finished scheduling a TXQ (which will
then be put back in the scheduling rotation if it isn't empty).
The driver must call ieee80211_txq_schedule_start() at the start of each
scheduling session, and ieee80211_txq_schedule_end() at the end. The API
then guarantees that the same TXQ is not returned twice in the same
session (so a driver can loop on ieee80211_next_txq() without worrying
about breaking the loop.
Usage of the new API is optional, so drivers can be ported one at a time.
In this patch, the actual scheduling performed by mac80211 is simple
round-robin, but a subsequent commit adds airtime fairness awareness to the
scheduler.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[minor kernel-doc fix, propagate sparse locking checks out]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's nothing much for mac80211 to do, so only pass through
the requests with minimal checks and tracing. The driver must
call cfg80211's results APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New bss param ftm_responder is used to notify the driver to
enable fine timing request (FTM) responder role in AP mode.
Plumb the new cfg80211 API for FTM responder statistics through to
the driver API in mac80211.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardwares have limitations on the packets' type in AMSDU.
Add an optional driver callback to determine if two skbs can
be used in the same AMSDU or not.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are specific cases, such as SAE authentication exchange, that
might require long duration to complete. For such cases, add support
for indicating to the driver the required duration of the prepare_tx()
operation, so the driver would still be able to complete the frame
exchange.
Currently, indicate the duration only for SAE authentication exchange,
as SAE authentication can take up to 2000 msec (as defined in IEEE
P802.11-REVmd D1.0 p. 3504).
As the patch modified the prepare_tx() callback API, also modify
the relevant code in iwlwifi.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit e937b8da5a.
Turns out that a new driver (mt76) is coming in through
Kalle's tree, and will conflict with this. It also has some
conflicting requirements, so we'll revisit this later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds an API to mac80211 to handle scheduling of TXQs and changes the
interface between driver and mac80211 for TXQ handling as follows:
- The wake_tx_queue callback interface no longer includes the TXQ. Instead,
the driver is expected to retrieve that from ieee80211_next_txq()
- Two new mac80211 functions are added: ieee80211_next_txq() and
ieee80211_schedule_txq(). The former returns the next TXQ that should be
scheduled, and is how the driver gets a queue to pull packets from. The
latter is called internally by mac80211 to start scheduling a queue, and
the driver is supposed to call it to re-schedule the TXQ after it is
finished pulling packets from it (unless the queue emptied).
The ath9k and ath10k drivers are changed to use the new API.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows the mesh sync (and debugfs) code to make incremental
TSF adjustments, avoiding any uncertainty introduced by delay in
programming absolute TSF.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement add/rm_nan_func functions and handle NAN function
termination notifications. Handle instance_id allocation for
NAN functions and implement the reconfig flow.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement nan_change_conf callback which allows to change current
NAN configuration (master preference and dual band operation).
Store the current NAN configuration in sdata, so it can be used
both to provide the driver the updated configuration with changes
and also it will be used in hw reconfig flows in next patches.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code doesn't do much besides allowing to start and
stop the vif.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No drivers implement this, relying either on the recursive
directory removal to remove their debugfs, or not having any
to start with. Remove the dead driver callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add support to MU-MIMO air sniffer according groupID:
in monitor mode, use a given MU-MIMO groupID to monitor stations
that belongs to that group using MU-MIMO.
add support for following a station according to its MAC address
using VHT MU-MIMO sniffer:
the monitors wait until they get an action MU-MIMO notification
frame, then parses it in order to find the groupID that corresponds
to the given MAC address and monitors packets destined to that
groupID using VHT MU-MIMO.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on which method the driver implements, userspace could
call this (indirectly, by getting station info) before the driver
knows about the station, possibly causing it to misbehave.
Therefore, add a check for sta->uploaded which indicates that the
driver knows about the station.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.
This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[rewrite commit message, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices, like iwlwifi, have RSS queues. This may cause a
situation where a disassociation is handled in control path and
results in station removal while there are prior RX frames
that were still not processed in other queues. When they will
be processed the station will be gone, and the frames will be
dropped.
Add a synchronization interface to avoid that. When driver returns
from the synchronization mac80211 may remove the station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel context driver operations can sleep, so add might_sleep()
and document this.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If drv_start() fails during hw_restart, all the running
interfaces are being closed/stopped, which results in
drv_stop() being called, although the driver was never
started successfully.
This might cause drivers to perform operations on uninitialized
memory (as they assume it was initialized on drv_start)
Consider the local->started flag, and call the driver's stop()
op only if drv_start() succeeded before.
Move drv_start() and drv_stop() to driver-ops.c, as they are no
longer simple wrappers.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining these functions have sizes and callsite counts
as follows:
drv_get_tsf: 634 bytes, 6 calls
drv_set_tsf: 626 bytes, 2 calls
drv_reset_tsf: 617 bytes, 2 calls
Total size reduction is about 4.2 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 755 bytes and there are
6 callsites.
Total size reduction is about 3.3 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 821 bytes and there are
2 callsites, reducing code size by about 800 bytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
[adjust code-style a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining these functions have sizes and callsite counts
as follows:
drv_add_interface: 638 bytes, 5 calls
drv_remove_interface: 611 bytes, 6 calls
drv_change_interface: 658 bytes, 1 call
Total size reduction is about 9 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 706 bytes and there are
2 callsites, reducing code size by about 700 bytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 785 bytes and there are
7 callsites.
Total size reduction is about 3.5 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the cfg80211's frame registration api receives wdev, however
mac80211 assumes per device filter configuration and ignores wdev.
Per device filtering is too wasteful, especially for multi-channel
devices.
Introduce new per vif frame registration API and use it for probe
request registrations in ieee80211_mgmt_frame_register()
Also call directly to ieee80211_configure_filter instead of using a work
since it is now allowed to sleep in ieee80211_mgmt_frame_register.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config,
after deinlining the function size is 3132 bytes and there are
7 callsites.
Total size reduction: about 20 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.
The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.
This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will be able to add more events, such as MLME events and
others. The low level driver may be interested in knowing
about these events to dump firmware data upon failures, or
to change parameters in case connection attempts fail etc...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In many cases, drivers can filter things like beacons that will
skew statistics reported by mac80211. To get correct statistics
in these cases, call drivers to obtain statistics and let them
override all values, filling values from mac80211 if the driver
didn't provide them. Not all of them make sense for the driver
to fill, so some are still always done by mac80211.
Note that this doesn't currently allow a driver to say "I know
this value is wrong, don't report it at all", or to sum it up
with a mac80211 value (as could be useful for "dropped misc"),
that can be added if it turns out to be needed.
This also gets rid of the get_rssi() method as is can now be
implemented using sta_statistics().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers with a firmware or chip-based rate lookup table to
use the most recent default rate selection without having to get it from
per-packet data or explicit ieee80211_get_tx_rate calls
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau