When a port joins a bridge which already has local FDB entries pointing
to the bridge device itself, we would like to offload those, so allow
the "dev" argument to be equal to the bridge too. The code already does
what we need in that case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat addresses added to the bridge itself in the same way as regular
ports and send out a notification so that drivers may sync it down to
the hardware FDB.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Annotate the writer side of fdb->dst:
- fdb_create()
- br_fdb_update()
- fdb_add_entry()
- br_fdb_external_learn_add()
with WRITE_ONCE() and the reader side:
- br_fdb_test_addr()
- br_fdb_update()
- fdb_fill_info()
- fdb_add_entry()
- fdb_delete_by_addr_and_port()
- br_fdb_external_learn_add()
- br_switchdev_fdb_notify()
with compiler barriers such that the readers do not attempt to reload
fdb->dst multiple times, leading to potentially different destination
ports when the fdb entry is updated concurrently.
This is especially important in read-side sections where fdb->dst is
used more than once, but let's convert all accesses for the sake of
uniformity.
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the standard IEC 62439-2, in case the node behaves as MRA
and needs to send Test frames on ring ports, then these Test frames need
to have an Option TLV and a Sub-Option TLV which has the type AUTO_MGR.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switchdev port leaves a LAG that is a bridge port, the switchdev
objects and port attributes offloaded to that port are not removed:
ip link add br0 type bridge
ip link add bond0 type bond mode 802.3ad
ip link set swp0 master bond0
ip link set bond0 master br0
bridge vlan add dev bond0 vid 100
ip link set swp0 nomaster
VLAN 100 will remain installed on swp0 despite it going into standalone
mode, because as far as the bridge is concerned, nothing ever happened
to its bridge port.
Let's extend the bridge vlan, fdb and mdb replay functions to take a
'bool adding' argument, and make DSA and ocelot call the replay
functions with 'adding' as false from the switchdev unsync path, for the
switch port that leaves the bridge.
Note that this patch in itself does not salvage anything, because in the
current pull mode of operation, DSA still needs to call the replay
helpers with adding=false. This will be done in another patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the arguments and local variables for the newly added switchdev
replay helpers can be const, so let's make them so.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a slight inconvenience in the switchdev replay helpers added
recently, and this is when:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
bridge vlan add dev bond0 vid 100
ip link set swp0 master bond0
ip link set swp1 master bond0
Since the underlying driver (currently only DSA) asks for a replay of
VLANs when swp0 and swp1 join the LAG because it is bridged, what will
happen is that DSA will try to react twice on the VLAN event for swp0.
This is not really a huge problem right now, because most drivers accept
duplicates since the bridge itself does, but it will become a problem
when we add support for replaying switchdev object deletions.
Let's fix this by adding a blank void *ctx in the replay helpers, which
will be passed on by the bridge in the switchdev notifications. If the
context is NULL, everything is the same as before. But if the context is
populated with a valid pointer, the underlying switchdev driver
(currently DSA) can use the pointer to 'see through' the bridge port
(which in the example above is bond0) and 'know' that the event is only
for a particular physical port offloading that bridge port, and not for
all of them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2c4eca3ef7 ("net: bridge: switchdev: include local flag
in FDB notifications"), the bridge emits SWITCHDEV_FDB_ADD_TO_DEVICE
events with the is_local flag populated (but we ignore it nonetheless).
We would like DSA to start treating this bit, but it is still not
populated by the replay helper, so add it there too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return statements are not needed in Void function.
Signed-off-by: gushengxian <gushengxian@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The continue statement at the end of a for-loop has no effect,
invert the if expression and remove the continue.
Addresses-Coverity: ("Continue has no effect")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a tunnel_dst null pointer dereference due to lockless
access in the tunnel egress path. When deleting a vlan tunnel the
tunnel_dst pointer is set to NULL without waiting a grace period (i.e.
while it's still usable) and packets egressing are dereferencing it
without checking. Use READ/WRITE_ONCE to annotate the lockless use of
tunnel_id, use RCU for accessing tunnel_dst and make sure it is read
only once and checked in the egress path. The dst is already properly RCU
protected so we don't need to do anything fancy than to make sure
tunnel_id and tunnel_dst are read only once and checked in the egress path.
Cc: stable@vger.kernel.org
Fixes: 11538d039a ("bridge: vlan dst_metadata hooks in ingress and egress paths")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the standard IEC 62439-2, the number of transitions needs
to be counted for each transition 'between' ring state open and ring
state closed and not from open state to closed state.
Therefore fix this for both ring and interconnect ring.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable br is assigned a value that is not being read after
exiting case IFLA_STATS_LINK_XSTATS_SLAVE. The assignment is
redundant and can be removed.
Addresses-Coverity ("Unused value")
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The br_ip6_multicast_add_router() prototype is defined only when
CONFIG_IPV6 is enabled, but the function is always referenced, so there
is this build error with CONFIG_IPV6 not defined:
net/bridge/br_multicast.c: In function ‘__br_multicast_enable_port’:
net/bridge/br_multicast.c:1743:3: error: implicit declaration of function ‘br_ip6_multicast_add_router’; did you mean ‘br_ip4_multicast_add_router’? [-Werror=implicit-function-declaration]
1743 | br_ip6_multicast_add_router(br, port);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
| br_ip4_multicast_add_router
net/bridge/br_multicast.c: At top level:
net/bridge/br_multicast.c:2804:13: warning: conflicting types for ‘br_ip6_multicast_add_router’
2804 | static void br_ip6_multicast_add_router(struct net_bridge *br,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
net/bridge/br_multicast.c:2804:13: error: static declaration of ‘br_ip6_multicast_add_router’ follows non-static declaration
net/bridge/br_multicast.c:1743:3: note: previous implicit declaration of ‘br_ip6_multicast_add_router’ was here
1743 | br_ip6_multicast_add_router(br, port);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this build error by moving the definition out of the #ifdef.
Fixes: a3c02e769e ("net: bridge: mcast: split multicast router state for IPv4 and IPv6")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_multicast_is_router takes two arguments when bridge IGMP is enabled
and just one when it's disabled, fix the stub to take two as well.
Fixes: 1a3065a268 ("net: bridge: mcast: prepare is-router function for mcast router split")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
To properly support routable multicast addresses in batman-adv in a
group-aware way, a batman-adv node needs to know if it serves multicast
routers.
This adds a function to the bridge to export this so that batman-adv
can then make full use of the Multicast Router Discovery capability of
the bridge.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have split the multicast router state into two, one for IPv4
and one for IPv6, also add individual timers to the mdb netlink router
port dump. Leaving the old timer attribute for backwards compatibility.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
A multicast router for IPv4 does not imply that the same host also is a
multicast router for IPv6 and vice versa.
To reduce multicast traffic when a host is only a multicast router for
one of these two protocol families, keep router state for IPv4 and IPv6
separately. Similar to how querier state is kept separately.
For backwards compatibility for netlink and switchdev notifications
these two will still only notify if a port switched from either no
IPv4/IPv6 multicast router to any IPv4/IPv6 multicast router or the
other way round. However a full netlink MDB router dump will now also
include a multicast router timeout for both IPv4 and IPv6.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants split router port deletion and notification
into two functions. When we disable a port for instance later we want to
only send one notification to switchdev and netlink for compatibility
and want to avoid sending one for IPv4 and one for IPv6. For that the
split is needed.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants move the protocol specific router list
and timer access to ip4 wrapper functions.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants move the protocol specific timer access to
an ip4 wrapper function.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants make br_multicast_is_router() protocol
family aware.
Note that for now br_ip6_multicast_is_router() uses the currently still
common ip4_mc_router_timer for now. It will be renamed to
ip6_mc_router_timer later when the split is performed.
While at it also renames the "1" and "2" constants in
br_multicast_is_router() to the MDB_RTR_TYPE_TEMP_QUERY and
MDB_RTR_TYPE_PERM enums.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants and as the br_multicast_mark_router() will
be split for that remove the select querier wrapper and instead add
ip4 and ip6 variants for br_multicast_query_received().
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants and to avoid IPv6 #ifdef clutter later add
some inline functions for the protocol specific parts in the mdb router
netlink code. Also the we need iterate over the port instead of router
list to be able put one router port entry with both the IPv4 and IPv6
multicast router info later.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants and to avoid IPv6 #ifdef clutter later add
two wrapper functions for router node retrieval in the payload
forwarding code.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants, rename the affected variable to the IPv4
version first to avoid some renames in later commits.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a crash in the function br_get_link_af_size_filtered,
as the port_exists(dev) is true and the rx_handler_data of dev is NULL.
But the rx_handler_data of dev is correct saved in vmcore.
The oops looks something like:
...
pc : br_get_link_af_size_filtered+0x28/0x1c8 [bridge]
...
Call trace:
br_get_link_af_size_filtered+0x28/0x1c8 [bridge]
if_nlmsg_size+0x180/0x1b0
rtnl_calcit.isra.12+0xf8/0x148
rtnetlink_rcv_msg+0x334/0x370
netlink_rcv_skb+0x64/0x130
rtnetlink_rcv+0x28/0x38
netlink_unicast+0x1f0/0x250
netlink_sendmsg+0x310/0x378
sock_sendmsg+0x4c/0x70
__sys_sendto+0x120/0x150
__arm64_sys_sendto+0x30/0x40
el0_svc_common+0x78/0x130
el0_svc_handler+0x38/0x78
el0_svc+0x8/0xc
In br_add_if(), we found there is no guarantee that
assigning rx_handler_data to dev->rx_handler_data
will before setting the IFF_BRIDGE_PORT bit of priv_flags.
So there is a possible data competition:
CPU 0: CPU 1:
(RCU read lock) (RTNL lock)
rtnl_calcit() br_add_slave()
if_nlmsg_size() br_add_if()
br_get_link_af_size_filtered() -> netdev_rx_handler_register
...
// The order is not guaranteed
... -> dev->priv_flags |= IFF_BRIDGE_PORT;
// The IFF_BRIDGE_PORT bit of priv_flags has been set
-> if (br_port_exists(dev)) {
// The dev->rx_handler_data has NOT been assigned
-> p = br_port_get_rcu(dev);
....
-> rcu_assign_pointer(dev->rx_handler_data, rx_handler_data);
...
Fix it in br_get_link_af_size_filtered, using br_port_get_check_rcu() and checking the return value.
Signed-off-by: Zhang Zhengming <zhangzhengming@huawei.com>
Reviewed-by: Zhao Lei <zhaolei69@huawei.com>
Reviewed-by: Wang Xiaogang <wangxiaogang3@huawei.com>
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 Multicast Router Advertisements parsing has the following two
issues:
For one thing, ICMPv6 MRD Advertisements are smaller than ICMPv6 MLD
messages (ICMPv6 MRD Adv.: 8 bytes vs. ICMPv6 MLDv1/2: >= 24 bytes,
assuming MLDv2 Reports with at least one multicast address entry).
When ipv6_mc_check_mld_msg() tries to parse an Multicast Router
Advertisement its MLD length check will fail - and it will wrongly
return -EINVAL, even if we have a valid MRD Advertisement. With the
returned -EINVAL the bridge code will assume a broken packet and will
wrongly discard it, potentially leading to multicast packet loss towards
multicast routers.
The second issue is the MRD header parsing in
br_ip6_multicast_mrd_rcv(): It wrongly checks for an ICMPv6 header
immediately after the IPv6 header (IPv6 next header type). However
according to RFC4286, section 2 all MRD messages contain a Router Alert
option (just like MLD). So instead there is an IPv6 Hop-by-Hop option
for the Router Alert between the IPv6 and ICMPv6 header, again leading
to the bridge wrongly discarding Multicast Router Advertisements.
To fix these two issues, introduce a new return value -ENODATA to
ipv6_mc_check_mld() to indicate a valid ICMPv6 packet with a hop-by-hop
option which is not an MLD but potentially an MRD packet. This also
simplifies further parsing in the bridge code, as ipv6_mc_check_mld()
already fully checks the ICMPv6 header and hop-by-hop option.
These issues were found and fixed with the help of the mrdisc tool
(https://github.com/troglobit/mrdisc).
Fixes: 4b3087c7e3 ("bridge: Snoop Multicast Router Advertisements")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
The compat layer needs to parse untrusted input (the ruleset)
to translate it to a 64bit compatible format.
We had a number of bugs in this department in the past, so allow users
to turn this feature off.
Add CONFIG_NETFILTER_XTABLES_COMPAT kconfig knob and make it default to y
to keep existing behaviour.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ebtables stores the table internal data (what gets passed to the
ebt_do_table() interpreter) in struct net.
nftables keeps the internal interpreter format in pernet lists
and passes it via the netfilter core infrastructure (priv pointer).
Do the same for ebtables: the nf_hook_ops are duplicated via kmemdup,
then the ops->priv pointer is set to the table that is being registered.
After that, the netfilter core passes this table info to the hookfn.
This allows to remove the pointers from struct net.
Same pattern can be applied to ip/ip6/arptables.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When CONFIG_NET_SWITCHDEV is disabled, the shim for switchdev_port_attr_set
inside br_mc_disabled_update returns -EOPNOTSUPP. This is not caught,
and propagated to the caller of br_multicast_add_port, preventing ports
from joining the bridge.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: ae1ea84b33 ("net: bridge: propagate error code and extack from br_mc_disabled_update")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in bugfix commit 6ab4c3117a ("net: bridge: don't notify
switchdev for local FDB addresses") as well as in this discussion:
https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/
the switchdev notifiers for FDB entries managed to have a zero-day bug,
which was that drivers would not know what to do with local FDB entries,
because they were not told that they are local. The bug fix was to
simply not notify them of those addresses.
Let us now add the 'is_local' bit to bridge FDB entries, and make all
drivers ignore these entries by their own choice.
Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having to add more and more arguments to
br_switchdev_fdb_call_notifiers, get rid of it and build the info
struct directly in br_switchdev_fdb_notify.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet switches might only be able to support disabling multicast
snooping globally, which is an issue for example when several bridges
span the same physical device and request contradictory settings.
Propagate the return value of br_mc_disabled_update() such that this
limitation is transmitted correctly to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like ip/ip6/arptables, the hooks have to be removed, then
synchronize_rcu() has to be called to make sure no more packets are being
processed before the ruleset data is released.
Place the hook unregistration in the pre_exit hook, then call the new
ebtables pre_exit function from there.
Years ago, when first netns support got added for netfilter+ebtables,
this used an older (now removed) netfilter hook unregister API, that did
a unconditional synchronize_rcu().
Now that all is done with call_rcu, ebtable_{filter,nat,broute} pernet exit
handlers may free the ebtable ruleset while packets are still in flight.
This can only happens on module removal, not during netns exit.
The new function expects the table name, not the table struct.
This is because upcoming patch set (targeting -next) will remove all
net->xt.{nat,filter,broute}_table instances, this makes it necessary
to avoid external references to those member variables.
The existing APIs will be converted, so follow the upcoming scheme of
passing name + hook type instead.
Fixes: aee12a0a37 ("ebtables: remove nf_hook_register usage")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ebtables currently uses net->xt.tables[BRIDGE], but upcoming
patch will move net->xt.tables away from struct net.
To avoid exposing x_tables internals to ebtables, use a private list
instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Provide bridge log support from nf_log_syslog.
After the merge there is no need to load the "real packet loggers",
all of them now reside in the same module.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The switch might have already added the VLAN tag through PVID hardware
offload. Keep this extra VLAN in the flowtable but skip it on egress.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the VLAN settings of the bridge and the port, the bridge can
either add or remove a tag. When vlan filtering is enabled, the fdb lookup
also needs to know the VLAN tag/proto for the destination address
To provide this, keep track of the stack of VLAN tags for the path in the
lookup context
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add .ndo_fill_forward_path for bridge devices.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to br_vlan_replay_one is returning an error return value but
this is not being assigned to err and the following check on err is
currently always false because err was initialized to zero. Fix this
by assigning err.
Addresses-Coverity: ("'Constant' variable guards dead code")
Fixes: 22f67cdfae ("net: bridge: add helper to replay VLANs installed on port")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MRP instance was created, the driver was notified that the
instance is created and then in a different callback about role of the
instance. But when the instance was deleted the driver was notified only
that the MRP instance is deleted and not also that the role is disabled.
This patch make sure that the driver is notified that the role is
changed to disabled before the MRP instance is deleted to have similar
callbacks with the creating of the instance. In this way it would
simplify the logic in the drivers.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this simple setup with DSA:
ip link add br0 type bridge vlan_filtering 1
ip link add bond0 type bond
ip link set bond0 master br0
ip link set swp0 master bond0
will not work because the bridge has created the PVID in br_add_if ->
nbp_vlan_init, and it has notified switchdev of the existence of VLAN 1,
but that was too early, since swp0 was not yet a lower of bond0, so it
had no reason to act upon that notification.
We need a helper in the bridge to replay the switchdev VLAN objects that
were notified since the bridge port creation, because some of them may
have been missed.
As opposed to the br_mdb_replay function, the vg->vlan_list write side
protection is offered by the rtnl_mutex which is sleepable, so we don't
need to queue up the objects in atomic context, we can replay them right
away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switchdev port starts offloading a LAG that is already in a
bridge and has an FDB entry pointing to it:
ip link set bond0 master br0
bridge fdb add dev bond0 00:01:02:03:04:05 master static
ip link set swp0 master bond0
the switchdev driver will have no idea that this FDB entry is there,
because it missed the switchdev event emitted at its creation.
Ido Schimmel pointed this out during a discussion about challenges with
switchdev offloading of stacked interfaces between the physical port and
the bridge, and recommended to just catch that condition and deny the
CHANGEUPPER event:
https://lore.kernel.org/netdev/20210210105949.GB287766@shredder.lan/
But in fact, we might need to deal with the hard thing anyway, which is
to replay all FDB addresses relevant to this port, because it isn't just
static FDB entries, but also local addresses (ones that are not
forwarded but terminated by the bridge). There, we can't just say 'oh
yeah, there was an upper already so I'm not joining that'.
So, similar to the logic for replaying MDB entries, add a function that
must be called by individual switchdev drivers and replays local FDB
entries as well as ones pointing towards a bridge port. This time, we
use the atomic switchdev notifier block, since that's what FDB entries
expect for some reason.
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a system with DSA ports, and udhcpcd is configured to bring
interfaces up as soon as they are created.
I create a bridge as follows:
ip link add br0 type bridge
As soon as I create the bridge and udhcpcd brings it up, I also have
avahi which automatically starts sending IPv6 packets to advertise some
local services, and because of that, the br0 bridge joins the following
IPv6 groups due to the code path detailed below:
33:33:ff:6d:c1:9c vid 0
33:33:00:00:00:6a vid 0
33:33:00:00:00:fb vid 0
br_dev_xmit
-> br_multicast_rcv
-> br_ip6_multicast_add_group
-> __br_multicast_add_group
-> br_multicast_host_join
-> br_mdb_notify
This is all fine, but inside br_mdb_notify we have br_mdb_switchdev_host
hooked up, and switchdev will attempt to offload the host joined groups
to an empty list of ports. Of course nobody offloads them.
Then when we add a port to br0:
ip link set swp0 master br0
the bridge doesn't replay the host-joined MDB entries from br_add_if,
and eventually the host joined addresses expire, and a switchdev
notification for deleting it is emitted, but surprise, the original
addition was already completely missed.
The strategy to address this problem is to replay the MDB entries (both
the port ones and the host joined ones) when the new port joins the
bridge, similar to what vxlan_fdb_replay does (in that case, its FDB can
be populated and only then attached to a bridge that you offload).
However there are 2 possibilities: the addresses can be 'pushed' by the
bridge into the port, or the port can 'pull' them from the bridge.
Considering that in the general case, the new port can be really late to
the party, and there may have been many other switchdev ports that
already received the initial notification, we would like to avoid
delivering duplicate events to them, since they might misbehave. And
currently, the bridge calls the entire switchdev notifier chain, whereas
for replaying it should just call the notifier block of the new guy.
But the bridge doesn't know what is the new guy's notifier block, it
just knows where the switchdev notifier chain is. So for simplification,
we make this a driver-initiated pull for now, and the notifier block is
passed as an argument.
To emulate the calling context for mdb objects (deferred and put on the
blocking notifier chain), we must iterate under RCU protection through
the bridge's mdb entries, queue them, and only call them once we're out
of the RCU read-side critical section.
There was some opportunity for reuse between br_mdb_switchdev_host_port,
br_mdb_notify and the newly added br_mdb_queue_one in how the switchdev
mdb object is created, so a helper was created.
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME attribute is only emitted from:
sysfs/ioctl/netlink
-> br_set_ageing_time
-> __set_ageing_time
therefore not at bridge port creation time, so:
(a) switchdev drivers have to hardcode the initial value for the address
ageing time, because they didn't get any notification
(b) that hardcoded value can be out of sync, if the user changes the
ageing time before enslaving the port to the bridge
We need a helper in the bridge, such that switchdev drivers can query
the current value of the bridge ageing time when they start offloading
it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean