When PFC is enabled for any UP in single TC configuration the driver didn't
collect the PFC XOFF RX stats. Though a single TC with PFC enabled is not a
common scenario do not prevent the driver from collecting stats if firmware
indicates that PFC is enabled.
Change-ID: Ie20bd58b07608b528f3c6d95894c9ae56b00077a
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For UMAC, we were not treating a race condition that happens in the
scan flows, because it was not using the same state flags. Now that
UMAC and LMAC scans use the same state flags, we can also handle the
race conditions for UMAC.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
UMAC scans now use the general scan status for almost everything, the
only part missing was in the scan complete notifications. Change it
to use the stopping flags instead of clearing the flags when the stop
comes from above and clean the handler function a bit.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The regular and scheduled scan functions are very similar, so they can
be combined into one.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Having explicit rx cmd header fields is useful, as it can
be used for event filtering (e.g. saving only debug logs,
rather than the whole data)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This check for family type is redundant as the if clause above
checks a family-dependent Boolean (which is not set for family 8000 anyway).
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The UMAC and LMAC scan_stop functions are now nearly identical, so
they can be combined into a single function instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We can only have one scan per type at the same time, so the code that
tries to stop several scans of a type is unnecessary. Remove that to
reduce code complexity.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We can only have one scan of each type running at the same time, so we
can remove one attribute in the UID information we save. We had array
index, UID and type, but only UID (== array_index) and type are
necessary. Refactor the code to use this simplified array.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for scan priority API with 8 levels instead of the
existing 3 levels. This API is needed to define the priority of
new ooc activities, e.g. gscan.
Add a TLV flag to indicate if the new API is supported so that
devices that does not support the new API will continue to use
the old one.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some LMAC specific functions had too generic names
(i.e. *_scan_offload_*) and were hard to distinguish from functions
that are really generic. Rename these functions to *_lmac_scan_* in
to make it more consistent and easier to read.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For consistency with the LMAC functions, rename the UMAC scan stop
function to iwl_mvm_umac_scan_stop(). Additionally, move things
around a bit to avoid an unnecessary forward declaration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For UMAC scans, we were simply jumping into another function when scan
stop functions were called, while for LMAC scans, the flow continued.
To make the flows cleaner and more balanced, combine the UMAC part
into the main stop functions. This also makes us take one step closer
into combining the state flags for both APIs.
Note that some STOPPING flags will be dangling in UMAC scans, but it
doesn't matter because they are not used in UMAC yet (and this will be
fixed in subsequent patches).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It is not necessary to stop regular scans when going out of idle
state. Previously, we were doing so for LMAC scans because the
iwl_mvm_scan_offload_stop() function was stopping both kinds of scans.
Now that we have more granularity, we can skip it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The iwl_mvm_scan_offload_stop() function is used to stop LMAC regular
scan, stop LMAC scheduled scan and stop UMAC scheduled scans (but not
UMAC regular scans), making it very difficult to read.
Reorganize the scan stopping functions by creating separate functions
to stop regular and scheduled scans, separating the LMAC stopping part
of the code from the rest and renaming the offload_stop function to
iwl_mvm_lmac_scan_stop().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The commit below fixed this for the old firmware API only.
Since the new firmware API hasn't been released yet, this
doesn't fix anything on currently existing firmwares.
This completes:
commit afcee962b0
Author: Eyal Shapira <eyal@wizery.com>
Date: Mon Feb 9 15:18:17 2015 +0200
iwlwifi: mvm: fix BT coex shared antenna activity check
type=bugfix
bug=not-tracked
fixes=unknown
Reviewed-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The iwl_mvm_config_sched_scan_profiles() function is only used in
scan.c, so remove the declaration from mvm.h and make it static.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After the scan refactor, the order of the SSIDs passed to the firmware
in all scans (including net-detect) are inverted. This was causing
the reporting code to use the wrong SSIDs. To fix this, invert the
array index when accessing the saved match SSIDs to report the
wake-up.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add UMAC scan iteration complete notification. This notification can
be enabled by setting scan_iter_notif_enabled through debugfs.
Upon receiving this notification, print the list of channels that
have been scanned in this iteration. This is useful for debugging.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When receiving scan iteration complete notification, print a list of
the channels that have been scanned in this iteration.
This is useful for debugging.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The BT_CONFIG command used to be very long, hence it was
allocated on the heap in the previous API. In the new API,
this command is much smaller, and can now safely be
allocated on the stack.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since we don't need to configure the Ack / CTS kill mask
anymore in the new API, we don't need to iterate all the
interfaces upon rssi event on one of the interfaces.
Remove that code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no need to have separate definitions for the UMAC scan types,
since they are the same as the LMAC types. Remove UMAC scan types and
use the generic ones instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to imeplement the extended VI session feature for Miracast, the FW
requires to detect the VI queue. The detection of the VI queue is done when
it is assigned to a STA with ADD_STA command, so by this time the FW expects
the queue to be already configured (mapped to VI AC and aggregation enabled).
Previously, the queue configuration was done after STA modificaton which
broke the extended VI session feature and resulted in higher latencies.
Fix this by calling iwl_mvm_enable_agg_txq before station modification.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the device fails to start correctly prior to loading the
regular runtime firmware (after having run the INIT firmware),
treat that error correctly by actually checking the return
value of _iwl_trans_start_hw() and stopping the device again
before returning an error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to the nl80211 documentation, we can neither advertise
scheduled scan nor netdetect address randomisation. However, all
the products that currently require this don't have a need for
the full randomisation.
Therefore, advertise the feature anyway which results in host-
based randomisation, done whenever the system suspends. This is
sufficient for the platforms currently requiring this feature.
If we ever extend this in the future to do full randomisation in
the firmware, then certainly this will still be sufficient for
the current requirements, so it doesn't make a lot of sense to
split the feature bits.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set a default NVM in case the userspace specifies a file
that doesn't match the hardware version. This allows not
to change the boot scripts when someone replaces the device
with a newer hardware step.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add debugfs entry for showing the different Tx power restrictions that are
caused due to various reasons.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Flow director is exported to user space using the ethtool ntuple
support. However, currently it only supports steering traffic to a
subset of the queues in use by the hardware. This change allows
flow director to specify queues that have been assigned to virtual
functions by partitioning the ring_cookie into a 8bit VF specifier
followed by 32bit queue index. At the moment we don't have any
ethernet drivers with more than 2^32 queues on a single function
as best I can tell and nor do I expect this to happen anytime
soon. This way the ring_cookie's normal use for specifying a queue
on a specific PCI function continues to work as expected.
CC: Alex Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The transport modules all need to allocate memory and set up
certain values. Refactor that code into a new common function
to share it and to simplify the error handling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The UMAC API supports multiple scan schedules, but now we use only a
single one. Change the comment to make this clear and avoid
confusion.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This removes the use of the two deprecated calls to the
macro PTR_RET in iwl_mvm_get_regdomain and replaces them
both to PTR_ERR_OR_ZERO.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
[Commit message editing]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The ring_cookie is 64 bits wide which is much larger than can be used
for actual queue index values. So provide some helper routines to
pack a VF index into the cookie. This is useful to steer packets to
a VF ring without having to know the queue layout of the device.
CC: Alex Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The radio cfg DWORD was taken from the wrong place in the
8000 HW family, after a line in the code was wrongly changed
by mistake. This broke several 8260 devices.
Fixes: 5dd9c68a85 ("iwlwifi: drop support for early versions of 8000")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The cmd_in_flight tracking was introduced to workaround faulty
power management hardware, by having the driver keep the NIC
awake as long as there are commands in flight. However, some of
the code handling this workaround was unconditionally executed,
which resulted with an inconsistent state where the driver assumed
that the NIC was awake although it wasn't.
Fix this by renaming 'cmd_in_flight' to 'cmd_hold_nic_awake' and
handling the NIC requested awake state only for hardwares for
which the workaround is needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Platform NVRAMs often contain values with spaces. Even if right now most
firmware-supported entries are simple values, we shouldn't reject these
with spaces. It was semi-confirmed by Broadcom in the early patch adding
support for platform NVRAMs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes brcmfmac dealing with NVRAM coming from platform e.g. from a
flash MTD partition. In such cases entries are separated by \0 instead
of \n which caused ignoring whole content after the first "comment".
While platform NVRAM doesn't usually contain comments, we switch to
COMMENT state after e.g. finding an unexpected char in key name.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With a simple use of snprintf and small buffer we can compare NVRAM
entry value with a full string. This way we avoid checking random chars
at magic offsets.
Tested on BCM43602 with NVRAM hacked to use v1 format.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Comparing NVRAM entry with a full filtering string is simpler than
comparing it with a short prefix and then checking random chars at magic
offsets. The cost of snprintf relatively low, we execute it just once.
Tested on BCM43602 with NVRAM hacked to use V2 format.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for the simplest of MediaTek Wi-Fi devices - MT7601U.
It is a single stream bgn chip with no bells or whistles.
This driver is partially based on Felix's mt76 but IMHO it doesn't
make sense to merge the two right now because MT7601U is a design
somewhere between old Ralink devices and new Mediatek chips. There
wouldn't be all that much code sharing with the devices mt76 supports.
Situation may obviously change when someone decides to extend m76 with
support for the more recent USB dongles.
The driver supports only station mode. I'm hoping to add AP support
when time allows.
This driver sat on GitHub for quite a while and got some testing there:
http://github.com/kuba-moo/mt7601u
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The fields of struct acpi_device are only known when CONFIG_ACPI is
defined. Fix this by using a helper function. This will resolve the
issue found in linux-next:
../brcmfmac/bcmsdh.c: In function 'brcmf_ops_sdio_probe':
../brcmfmac/bcmsdh.c:1139:7: error: dereferencing pointer to incomplete type
adev->flags.power_manageable = 0;
^
Fixes: f0992ace68 ("brcmfmac: prohibit ACPI power management ...")
Cc: Fu, Zhonghui <zhonghui.fu@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When headphone mic boost is above zero, some 10 - 20 second delay
might occur before the headphone mic is operational.
Therefore disable the headphone mic boost control (recording gain is
sufficient even without it).
(Note: this patch is not about the headset mic, it's about the less
common mic-in only mode.)
BugLink: https://bugs.launchpad.net/bugs/1454235
Suggested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A recent change removed the need for locking around writing
to "sync_action" (and various other places), but introduced a
subtle race.
When e.g. setting 'reshape' on a 'frozen' array, the 'frozen'
flag is cleared before 'reshape' is set, so the md thread can
get in and start trying recovery - which isn't wanted.
So instead of clearing MD_RECOVERY_FROZEN for any command
except 'frozen', only clear it when each specific command
is parsed. This allows the handling of 'reshape' to clear
the bit while a lock is held.
Also remove some places where we set MD_RECOVERY_NEEDED,
as it is always set on non-error exit of the function.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 6791875e2e ("md: make reconfig_mutex optional for writes to md sysfs files.")
The vti6_rcv_cb and vti_rcv_cb calls were leaving the skb->mark modified
after completing the function. This resulted in the original skb->mark
value being lost. Since we only need skb->mark to be set for
xfrm_policy_check we can pull the assignment into the rcv_cb calls and then
just restore the original mark after xfrm_policy_check has been completed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This change makes it so that if a tunnel is defined we just use the mark
from the tunnel instead of the mark from the skb header. By doing this we
can avoid the need to set skb->mark inside of the tunnel receive functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Instead of modifying skb->mark we can simply modify the flowi_mark that is
generated as a result of the xfrm_decode_session. By doing this we don't
need to actually touch the skb->mark and it can be preserved as it passes
out through the tunnel.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Neerav Parikh