The VGA arbiter is really PCI-specific and doesn't depend on any GPU
things. Move it to the PCI subsystem.
Note that misc_init() must be called before vga_arb_device_init(). These
are both subsys_initcalls, so this ordering depends on the link order,
which is determined by drivers/Makefile:
obj-y += pci/
obj-y += char/ <-- misc_init()
obj-y += gpu/ <-- vga_arb_device_init() (before this commit)
The drivers/pci/ subsys_initcalls are called *before* misc_init(), so
convert vga_arb_device_init() to subsys_initcall_sync(), which is called
after *all* subsys_initcalls.
Link: https://lore.kernel.org/r/20220224224753.297579-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The VGA arbitration is entirely based on pci_dev structures, so just pass
that back to the set_vga_decode callback.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716061634.2446357-8-hch@lst.de
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
All callers pass NULL as the irq_set_state argument, so remove it and
the ->irq_set_state member in struct vga_device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716061634.2446357-7-hch@lst.de
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Kerneldoc comments should be at the implementation side, not in the
header just declaring the prototype.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716061634.2446357-4-hch@lst.de
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
vga_conflicts only has a single caller and none of the arch overrides
mentioned in the comment. Just remove it and the thus dead check in the
caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716061634.2446357-3-hch@lst.de
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Commit 3d42f1ddc4 ("vgaarb: Keep adding VGA device in queue") assumes
the first device is an integrated GPU. However, on AMD platforms an
integrated GPU can have higher PCI device number than a discrete GPU.
Integrated GPU on ACPI platform generally has _DOD and _DOS method, so
use that as predicate to find integrated GPU. If the new strategy
doesn't work, fallback to use the first device as boot VGA.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519135723.525997-1-kai.heng.feng@canonical.com
-----BEGIN PGP SIGNATURE-----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=xRTv
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Decode PCIe 64 GT/s link speed (Gustavo Pimentel)
- Remove unused HAVE_PCI_SET_MWI (Heiner Kallweit)
- Reduce pci_set_cacheline_size() message to debug level (Heiner
Kallweit)
- Fix pci_slot_release() NULL pointer dereference (Jubin Zhong)
- Unify ECAM constants in native PCI Express drivers (Krzysztof
Wilczyński)
- Return u8 from pci_find_capability() and similar (Puranjay Mohan)
- Return u16 from pci_find_ext_capability() and similar (Bjorn
Helgaas)
- Fix ACPI companion lookup for device 0 on the root bus (Rafael J.
Wysocki)
Resource management:
- Keep both device and resource name for config space remaps
(Alexander Lobakin)
- Bounds-check command-line resource alignment requests (Bjorn
Helgaas)
- Fix overflow in command-line resource alignment requests (Colin Ian
King)
Driver binding:
- Avoid duplicate IDs in driver dynamic IDs list (Zhenzhong Duan)
Power management:
- Save/restore Precision Time Measurement Capability for
suspend/resume (David E. Box)
- Disable PTM during suspend to save power (David E. Box)
- Add sysfs attribute for device power state (Maximilian Luz)
- Rename pci_wakeup_bus() to pci_resume_bus() (Mika Westerberg)
- Do not generate wakeup event when runtime resuming device (Mika
Westerberg)
- Save/restore ASPM L1SS Capability for suspend/resume (Vidya Sagar)
Virtualization:
- Mark AMD Raven iGPU ATS as broken in some platforms (Alex Deucher)
- Add function 1 DMA alias quirk for Marvell 9215 SATA controller
(Bjorn Helgaas)
MSI:
- Disable MSI for Pericom PCIe-USB adapter (Andy Shevchenko)
- Improve warnings for 32-bit-limited MSI support (Vidya Sagar)
Error handling:
- Cache RCEC EA Capability offset in pci_init_capabilities() (Sean V
Kelley)
- Rename reset_link() to reset_subordinates() (Sean V Kelley)
- Write AER Capability only when we control it (Sean V Kelley)
- Clear AER status only when we control AER (Sean V Kelley)
- Bind RCEC devices to the Root Port driver (Qiuxu Zhuo)
- Recover from RCiEP AER errors (Qiuxu Zhuo)
- Recover from RCEC AER errors (Sean V Kelley)
- Add pcie_link_rcec() to associate RCiEPs (Sean V Kelley)
- Add pcie_walk_rcec() to RCEC AER handling (Sean V Kelley)
- Add pcie_walk_rcec() to RCEC PME handling (Sean V Kelley)
- Add RCEC AER error injection support (Qiuxu Zhuo)
Broadcom iProc PCIe controller driver:
- Fix out-of-bound array accesses (Bharat Gooty)
- Invalidate correct PAXB inbound windows (Roman Bacik)
- Enhance PCIe Link information display (Srinath Mannam)
Cadence PCIe controller driver:
- Make "cdns,max-outbound-regions" property optional (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Offset client MSI-X vectors (Jon Derrick)
- Update type of __iomem pointers (Krzysztof Wilczyński)
NVIDIA Tegra PCIe controller driver:
- Move "dbi" accesses to post common DWC initialization (Vidya Sagar)
- Read "dbi" base address to program in application logic (Vidya
Sagar)
- Fix ASPM-L1SS advertisement disable code (Vidya Sagar)
- Set DesignWare IP version (Vidya Sagar)
- Continue unconfig sequence even if parts fail (Vidya Sagar)
- Check return value of tegra_pcie_init_controller() (Vidya Sagar)
- Disable LTSSM during L2 entry (Vidya Sagar)
Qualcomm PCIe controller driver:
- Document PCIe bindings for SM8250 SoC (Manivannan Sadhasivam)
- Add SM8250 SoC support (Manivannan Sadhasivam)
- Add support for configuring BDF to SID mapping for SM8250
(Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- rcar: Drop unused members from struct rcar_pcie_host (Lad
Prabhakar)
- PCI: rcar-pci-host: Document r8a774e1 bindings (Lad Prabhakar)
- PCI: rcar-pci-host: Convert bindings to json-schema (Yoshihiro
Shimoda)
- PCI: rcar-pci-host: Document r8a77965 bindings (Yoshihiro Shimoda)
Samsung Exynos PCIe controller driver:
- Rework driver to support Exynos5433 PCIe PHY (Jaehoon Chung)
- Rework driver to support Exynos5433 variant (Jaehoon Chung)
- Drop samsung,exynos5440-pcie binding (Marek Szyprowski)
- Add the samsung,exynos-pcie binding (Marek Szyprowski)
- Add the samsung,exynos-pcie-phy binding (Marek Szyprowski)
Synopsys DesignWare PCIe controller driver:
- Support multiple ATU memory regions (Rob Herring)
- Move intel-gw ATU offset out of driver match data (Rob Herring)
- Move "dbi", "dbi2", and "addr_space" resource setup into common
code (Rob Herring)
- Remove intel-gw unneeded function wrappers (Rob Herring)
- Ensure all outbound ATU windows are reset (Rob Herring)
- Use the common MSI irq_chip in dra7xx (Rob Herring)
- Drop the .set_num_vectors() host op (Rob Herring)
- Move MSI interrupt setup into DWC common code (Rob Herring)
- Rework MSI initialization (Rob Herring)
- Move link handling into common code (Rob Herring)
- Move dw_pcie_msi_init() into core (Rob Herring)
- Move dw_pcie_setup_rc() to DWC common code (Rob Herring)
- Remove unnecessary wrappers around dw_pcie_host_init() (Rob
Herring)
- Drop keystone duplicated 'num-viewport'" (Rob Herring)
- Move inbound and outbound windows to common struct (Rob Herring)
- Detect number of iATU windows (Rob Herring)
- Warn if non-prefetchable memory aperture size is > 32-bit (Vidya
Sagar)
- Add support to program ATU for >4GB memory (Vidya Sagar)
- Set 32-bit DMA mask for MSI target address allocation (Vidya Sagar)
TI J721E PCIe driver:
- Fix "ti,syscon-pcie-ctrl" to take argument (Kishon Vijay Abraham I)
- Add host mode dt-bindings for TI's J7200 SoC (Kishon Vijay Abraham
I)
- Add EP mode dt-bindings for TI's J7200 SoC (Kishon Vijay Abraham I)
- Get offset within "syscon" from "ti,syscon-pcie-ctrl" phandle arg
(Kishon Vijay Abraham I)
TI Keystone PCIe controller driver:
- Enable compile-testing on !ARM (Alex Dewar)"
* tag 'pci-v5.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (100 commits)
PCI: Add function 1 DMA alias quirk for Marvell 9215 SATA controller
PCI/ACPI: Fix companion lookup for device 0 on the root bus
PCI: Keep both device and resource name for config space remaps
PCI: xgene: Removed unused ".bus_shift" initialisers from pci-xgene.c
PCI: vmd: Update type of the __iomem pointers
PCI: iproc: Convert to use the new ECAM constants
PCI: thunder-pem: Add constant for custom ".bus_shift" initialiser
PCI: Unify ECAM constants in native PCI Express drivers
PCI: Disable PTM during suspend to save power
PCI/PTM: Save/restore Precision Time Measurement Capability for suspend/resume
PCI: Mark AMD Raven iGPU ATS as broken in some platforms
PCI: j721e: Get offset within "syscon" from "ti,syscon-pcie-ctrl" phandle arg
dt-bindings: PCI: Add EP mode dt-bindings for TI's J7200 SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J7200 SoC
dt-bindings: pci: ti,j721e: Fix "ti,syscon-pcie-ctrl" to take argument
PCI: dwc: Set 32-bit DMA mask for MSI target address allocation
PCI: qcom: Add support for configuring BDF to SID mapping for SM8250
PCI: Reduce pci_set_cacheline_size() message to debug level
PCI: Remove unused HAVE_PCI_SET_MWI
PCI: qcom: Add SM8250 SoC support
...
A "wakeup" is a signal from a device telling the system that the device or
the whole system should be awakened and made active. PCI devices are made
active by "resuming" them.
pci_wakeup_bus() is not involved with the wakeup signal; it *resumes*
devices on a bus (possibly in response to a wakeup signal, but that's at a
higher level).
Rename pci_wakeup_bus() to pci_resume_bus() to better reflect what it does.
No functional change intended.
[bhelgaas: commit log, reorder before removal of pci_wakeup_event()]
Link: https://lore.kernel.org/r/20201125090733.77782-2-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes linking fail when fbcon/fbdev is modular and vgaswitcheroo is
enabled:
x86_64-linux-gnu-ld: drivers/gpu/vga/vga_switcheroo.o: in function `vga_switchto_stage2':
vga_switcheroo.c:(.text+0x997): undefined reference to `fbcon_remap_all'
Unfortunately this means that in a default allmodconfig we will disable vgaswitcheroo.
v2: I first tried to fix this with an EXPORT_SYMBOL, but vga_switcheroo is
never a module, so this doesn't work.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 1cd51b5d20 ("vgaswitcheroo: call fbcon_remap_all directly")
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Yisheng Xie <ysxie@foxmail.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190624092153.23375-1-daniel.vetter@ffwll.ch
topic/remove-fbcon-notifiers:
- remove fbdev notifier usage for fbcon, as prep work to clean up the fbcon locking
- assorted locking checks in vt/console code
- assorted notifier and cleanups in fbdev and backlight code
This is the pull request that was sent out, plus the compile fix for
sh4 reported by kbuild.
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Also, because there is no need to save the file dentry, remove the local
variable and just recursively delete the whole directory when shutting
down.
Cc: Lukas Wunner <lukas@wunner.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613114455.GA13119@kroah.com
While at it, clean up the interface a bit and push the console locking
into fbcon.c.
v2: Remove now outdated comment (Lukas).
v3: Forgot to add static inline to the dummy function.
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Yisheng Xie <ysxie@foxmail.com>
Cc: linux-fbdev@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190528090304.9388-30-daniel.vetter@ffwll.ch
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Split out some i915 code into the fb_helper to allow the above
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXIlYNQAKCRDj7w1vZxhR
xdsRAP0TnlDCQHcAY8U41jrWgSg2rNYNn/aT+PEXo7uoEy0AzwEAtv9tzk2309xn
wNT0c8wJU7l190VD8ZuikwT/19Y+pgw=
=3SKX
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2019-03-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
- qxl: Remove the conflicting framebuffers earlier
- Split out some i915 code into the fb_helper to allow the above
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190313192158.k3qssf733khsqodn@flea
This driver depends on the PCI infrastructure, but the dependency has
not been explicitly called out.
Fixes: 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=UV0m
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-11-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21, part 1:
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/be7ebd91-edd9-8fa4-4286-1c57e3165113@linux.intel.com
The commit 37a3a98ef6 ("ALSA: hda - Enable runtime PM only for
discrete GPU") added a new ops gpu_bound to be called when GPU gets
bound. The patch overlooked, however, that vga_switcheroo_enable() is
called only once at GPU is bound. When an audio client is registered
after that point, it would miss the gpu_bound call. This leads to the
unexpected lack of runtime PM in HD-audio side.
For addressing that regression, just call gpu_bound callback manually
at vga_switcheroo_register_audio_client() when the GPU was already
bound.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201615
Fixes: 37a3a98ef6 ("ALSA: hda - Enable runtime PM only for discrete GPU")
Cc: <stable@vger.kernel.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If failed to find the deivice owning the boot framebuffer,
try to use the first VGA device instead of the last one.
Usually the 1st device is integrated GPU who owns the boot framebuffer.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1535739600-8842-2-git-send-email-aaron.ma@canonical.com
EFI GOP uses 64-bit frame buffer address when some BIOS
disabled CSM support. vgaarb only stores lfb_base,
this will lead boot framebuffer to wrong device.
Add ext_lfb_base support to use 64-bit fb address.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1535739600-8842-1-git-send-email-aaron.ma@canonical.com
The recent change of vga_switcheroo allowed the runtime PM for
HD-audio on AMD GPUs, but this also resulted in a regression. When
the HD-audio controller driver gets runtime-suspended, HD-audio link
is turned off, and the hotplug notification is ignored. This leads to
the inconsistent audio state (the connection isn't notified and ELD is
ignored).
The best fix would be to implement the proper ELD notification via the
audio component, but it's still not ready. As a quick workaround,
this patch adds the check of runtime_idle and allows the runtime
suspend only when the vga_switcheroo is bound with discrete GPU.
That is, a system with a single GPU and APU would be again without
runtime PM to keep the HD-audio link for the hotplug notification and
ELD read out.
Also, the codec->auto_runtime_pm flag is set only for the discrete GPU
at the time GPU gets bound via vga_switcheroo (i.e. only dGPU is
forcibly runtime-PM enabled), so that APU can still get the ELD
notification.
For identifying which GPU is bound, a new vga_switcheroo client
callback, gpu_bound, is implemented. The vga_switcheroo simply calls
this when GPU is bound, and tells whether it's dGPU or APU.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200945
Fixes: 07f4f97d7b ("vga_switcheroo: Use device link for HDA controller")
Reported-by: Jian-Hong Pan <jian-hong@endlessm.com>
Tested-by: Jian-Hong Pan <jian-hong@endlessm.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On modern laptop, there are more and more platforms
have two GPUs, and each of them maybe have audio codec
for HDMP/DP output. For some dGPU which is no output,
audio codec usually is disabled.
In currect HDA audio driver, it will set all codec as
VGA_SWITCHEROO_DIS, the audio which is binded to UMA
will be suspended if user use debugfs to contorl power
In HDA driver side, it is difficult to know which GPU
the audio has binded to. So set the bound gpu pci dev
to vga_switcheroo.
if the audio client is not the third registration, audio
id will set in vga_switcheroo enable function. if the
audio client is the last registration when vga_switcheroo
_ready() get true, we should get audio client id from bound
GPU directly.
Signed-off-by: Jim Qu <Jim.Qu@amd.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
When switching the display on muxed machines, we currently force the HDA
controller into runtime suspend on the previously used GPU and into
runtime active state on the newly used GPU.
That's unnecessary if the GPU uses driver power control, we can just let
the audio device autosuspend or autoresume as it sees fit.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/098ed883460eb4976a899eac6f5192fefc877c0f.1520068884.git.lukas@wunner.de
Back in 2013, runtime PM for GPUs with integrated HDA controller was
introduced with commits 0d69704ae3 ("gpu/vga_switcheroo: add driver
control power feature. (v3)") and 246efa4a07 ("snd/hda: add runtime
suspend/resume on optimus support (v4)").
Briefly, the idea was that the HDA controller is forced on and off in
unison with the GPU.
The original code is mostly still in place even though it was never a
100% perfect solution: E.g. on access to the HDA controller, the GPU
is powered up via vga_switcheroo_runtime_resume_hdmi_audio() but there
are no provisions to keep it resumed until access to the HDA controller
has ceased: The GPU autosuspends after 5 seconds, rendering the HDA
controller inaccessible.
Additionally, a kludge is required when hda_intel.c probes: It has to
check whether the GPU is powered down (check_hdmi_disabled()) and defer
probing if so.
However in the meantime (in v4.10) the driver core has gained a feature
called device links which promises to solve such issues in a clean way:
It allows us to declare a dependency from the HDA controller (consumer)
to the GPU (supplier). The PM core then automagically ensures that the
GPU is runtime resumed as long as the HDA controller's ->probe hook is
executed and whenever the HDA controller is accessed.
By default, the HDA controller has a dependency on its parent, a PCIe
Root Port. Adding a device link creates another dependency on its
sibling:
PCIe Root Port
^ ^
| |
| |
HDA ===> GPU
The device link is not only used for runtime PM, it also guarantees that
on system sleep, the HDA controller suspends before the GPU and resumes
after the GPU, and on system shutdown the HDA controller's ->shutdown
hook is executed before the one of the GPU. It is a complete solution.
Using this functionality is as simple as calling device_link_add(),
which results in a dmesg entry like this:
pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
The code for the GPU-governed audio power management can thus be removed
(except where it's still needed for legacy manual power control).
The device link is added in a PCI quirk rather than in hda_intel.c.
It is therefore legal for the GPU to runtime suspend to D3cold even if
the HDA controller is not bound to a driver or if CONFIG_SND_HDA_INTEL
is not enabled, for accesses to the HDA controller will cause the GPU to
wake up regardless if they're occurring outside of hda_intel.c (think
config space readout via sysfs).
Contrary to the previous implementation, the HDA controller's power
state is now self-governed, rather than GPU-governed, whereas the GPU's
power state is no longer fully self-governed. (The HDA controller needs
to runtime suspend before the GPU can.)
It is thus crucial that runtime PM is always activated on the HDA
controller even if CONFIG_SND_HDA_POWER_SAVE_DEFAULT is set to 0 (which
is the default), lest the GPU stays awake. This is achieved by setting
the auto_runtime_pm flag on every codec and the AZX_DCAPS_PM_RUNTIME
flag on the HDA controller.
A side effect is that power consumption might be reduced if the GPU is
in use but the HDA controller is not, because the HDA controller is now
allowed to go to D3hot. Before, it was forced to stay in D0 as long as
the GPU was in use. (There is no reduction in power consumption on my
Nvidia GK107, but there might be on other chips.)
The code paths for legacy manual power control are adjusted such that
runtime PM is disabled during power off, thereby preventing the PM core
from resuming the HDA controller.
Note that the device link is not only added on vga_switcheroo capable
systems, but for *any* GPU with integrated HDA controller. The idea is
that the HDA controller streams audio via connectors located on the GPU,
so the GPU needs to be on for the HDA controller to do anything useful.
This commit implicitly fixes an unbalanced runtime PM ref upon unbind of
hda_intel.c: On ->probe, a runtime PM ref was previously released under
the condition "azx_has_pm_runtime(chip) || hda->use_vga_switcheroo", but
on ->remove a runtime PM ref was only acquired under the first of those
conditions. Thus, binding and unbinding the driver twice on a
vga_switcheroo capable system caused the runtime PM refcount to drop
below zero. The issue is resolved because the AZX_DCAPS_PM_RUNTIME flag
is now always set if use_vga_switcheroo is true.
For more information on device links please refer to:
https://www.kernel.org/doc/html/latest/driver-api/device_link.html
Documentation/driver-api/device_link.rst
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/51bd38360ff502a8c42b1ebf4405ee1d3f27118d.1520068884.git.lukas@wunner.de
If DRM drivers use runtime PM, they currently notify vga_switcheroo
whenever they ->runtime_suspend or ->runtime_resume to update
vga_switcheroo's internal power state tracking.
That's essentially a duplication of a functionality performed by the
PM core as it already tracks the GPU's power state and vga_switcheroo
can always query it.
Introduce a new internal helper vga_switcheroo_pwr_state() which does
just that if runtime PM is used, or falls back to vga_switcheroo's
internal power state tracking if manual power control is used.
Drop a redundant power state check in set_audio_state() while at it.
This removes one of the two purposes of the notification mechanism
implemented by vga_switcheroo_set_dynamic_switch(). The other one is
power management of the audio device and we'll remove that next.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/0aa49d735b988aa04524a8dc339582ace33f0f94.1520068884.git.lukas@wunner.de
When cutting power to a GPU and its integrated HDA controller, their
cached current_state should be updated to D3cold to reflect reality.
We currently rely on the DRM and HDA drivers to do that, however:
- The HDA driver updates the current_state in azx_vs_set_state(), which
will no longer be called with driver power control once we migrate to
device links. (It will still be called with manual power control.)
- If the HDA device is not bound, its current_state remains at D0 even
though the GPU driver may decide to go to D3cold.
- The DRM drivers update the current_state using pci_set_power_state()
which can't put the device into a deeper power state than D3hot if the
GPU is not deemed power-manageable by the platform (even though it
*is* power-manageable by some nonstandard means, such as a _DSM).
Centralize updating the current_state of the GPU and HDA controller in
vga_switcheroo's ->runtime_suspend hook to overcome these deficiencies.
The GPU and HDA controller are two functions of the same PCI device
(VGA class device on function 0 and audio device on function 1) and
no other PCI devices reside on the same bus since this is a PCIe
point-to-point link, so we can just walk the bus and update the
current_state of all devices.
On ->runtime_resume, the HDA controller is in D0uninitialized state.
Resume to D0active and then let it autosuspend as it sees fit.
Note that vga_switcheroo_init_domain_pm_ops() is not supposed to be
called by hybrid graphics laptops which power down the GPU via its root
port's _PR3 resources and consequently vga_switcheroo_runtime_suspend()
is not used. On those laptops, the root port is power-manageable by the
platform (instead of by a nonstandard means) and the current_state is
therefore updated by the PCI core through the following call chain:
pci_set_power_state()
__pci_complete_power_transition()
pci_bus_set_current_state()
Resuming to D0active happens through:
pci_set_power_state()
__pci_start_power_transition()
pci_wakeup_bus()
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/8416958482c8c42d6f311ea5c1e5a65ccf21f5db.1520068884.git.lukas@wunner.de
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default VGA device is normally set in vga_arbiter_add_pci_device() when
we call it for the first enabled device that can be accessed with the
legacy VGA resources ([mem 0xa0000-0xbffff], etc.)
That default device can be overridden by an EFI device that owns the boot
framebuffer. As a fallback, we can also select a VGA device that can't be
accessed via legacy VGA resources, or a VGA device that isn't even enabled.
Factor out this EFI and fallback selection from vga_arb_device_init() into
a separate vga_arb_select_default_device() function. This doesn't change
any behavior, but it untangles the "bridge control possible" checking and
messages from the default device selection.
Tested-by: Zhou Wang <wangzhou1@hisilicon.com> # D05 Hisi Hip07, Hip08
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171013034729.14630.30419.stgit@bhelgaas-glaptop.roam.corp.google.com
Daniel Axtens reported that on the HiSilicon D05 board, the VGA device is
behind a bridge that doesn't support PCI_BRIDGE_CTL_VGA, so the VGA arbiter
never selects it as the default, which means Xorg auto-detection doesn't
work.
VGA is a legacy PCI feature: a VGA device can respond to addresses, e.g.,
[mem 0xa0000-0xbffff], [io 0x3b0-0x3bb], [io 0x3c0-0x3df], etc., that are
not configurable by BARs. Consequently, multiple VGA devices can conflict
with each other. The VGA arbiter avoids conflicts by ensuring that those
legacy resources are only routed to one VGA device at a time.
The arbiter identifies the "default VGA" device, i.e., a legacy VGA device
that was used by boot firmware. It selects the first device that:
- is of PCI_CLASS_DISPLAY_VGA,
- has both PCI_COMMAND_IO and PCI_COMMAND_MEMORY enabled, and
- has PCI_BRIDGE_CTL_VGA set in all upstream bridges.
Some systems don't have such a device. For example, if a host bridge
doesn't support I/O space, PCI_COMMAND_IO probably won't be enabled for any
devices below it. Or, as on the HiSilicon D05, the VGA device may be
behind a bridge that doesn't support PCI_BRIDGE_CTL_VGA, so accesses to the
legacy VGA resources will never reach the device.
This patch extends the arbiter so that if it doesn't find a device that
meets all the above criteria, it selects the first device that:
- is of PCI_CLASS_DISPLAY_VGA and
- has PCI_COMMAND_IO or PCI_COMMAND_MEMORY enabled
If it doesn't find even that, it selects the first device that:
- is of class PCI_CLASS_DISPLAY_VGA.
Such a device may not be able to use the legacy VGA resources, but most
drivers can operate the device without those. Setting it as the default
device means its "boot_vga" sysfs file will contain "1", which Xorg (via
libpciaccess) uses to help select its default output device.
This fixes Xorg auto-detection on some arm64 systems (HiSilicon D05 in
particular; see the link below).
It also replaces the powerpc fixup_vga() quirk, albeit with slightly
different semantics: the quirk selected the first VGA device we found, and
overrode that selection with any enabled VGA device we found. If there
were several enabled VGA devices, the *last* one we found would become the
default.
The code here instead selects the *first* enabled VGA device we find, and
if none are enabled, the first VGA device we find.
Link: http://lkml.kernel.org/r/20170901072744.2409-1-dja@axtens.net
Tested-by: Daniel Axtens <dja@axtens.net> # arm64, ppc64-qemu-tcg
Tested-by: Zhou Wang <wangzhou1@hisilicon.com> # D05 Hisi Hip07, Hip08
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171013034721.14630.65913.stgit@bhelgaas-glaptop.roam.corp.google.com
Rename:
wait_queue_t => wait_queue_entry_t
'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.
Start sorting this out by renaming it to 'wait_queue_entry_t'.
This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
First slice of drm-misc-next for 4.12:
Core/subsystem-wide:
- link status core patch from Manasi, for signalling link train fail
to userspace. I also had the i915 patch in here, but that had a
small buglet in our CI, so reverted.
- more debugfs_remove removal from Noralf, almost there now (Noralf
said he'll try to follow up with the stragglers).
- drm todo moved into kerneldoc, for better visibility (see
Documentation/gpu/todo.rst), lots of starter tasks in there.
- devm_ of helpers + use it in sti (from Ben Gaignard, acked by Rob
Herring)
- extended framebuffer fbdev support (for fbdev flipping), and vblank
wait ioctl fbdev support (Maxime Ripard)
- misc small things all over, as usual
- add vblank callbacks to drm_crtc_funcs, plus make lots of good use
of this to simplify drivers (Shawn Guo)
- new atomic iterator macros to unconfuse old vs. new state
Small drivers:
- vc4 improvements from Eric
- vc4 kerneldocs (Eric)!
- tons of improvements for dw-mipi-dsi in rockchip from John Keeping
and Chris Zhong.
- MAINTAINERS entries for drivers managed in drm-misc. It's not yet
official, still an experiment, but definitely not complete fail and
better to avoid confusion. We kinda screwed that up with drm-misc a
bit when we started committers last year.
- qxl atomic conversion (Gabriel Krisman)
- bunch of virtual driver polish (qxl, virgl, ...)
- misc tiny patches all over
This is the first time we've done the same merge-window blackout for
drm-misc as we've done for drm-intel for ages, hence why we have a
_lot_ of stuff queued already. But it's still only half of drm-intel
(room to grow!), and the drivers in drm-misc experiment seems to work
at least insofar as that you also get lots of driver updates here
alredy.
* tag 'drm-misc-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-misc: (141 commits)
drm/vc4: Fix OOPSes from trying to cache a partially constructed BO.
drm/vc4: Fulfill user BO creation requests from the kernel BO cache.
Revert "drm/i915: Implement Link Rate fallback on Link training failure"
drm/fb-helper: implement ioctl FBIO_WAITFORVSYNC
drm: Update drm_fbdev_cma_init documentation
drm/rockchip/dsi: add dw-mipi power domain support
drm/rockchip/dsi: fix insufficient bandwidth of some panel
dt-bindings: add power domain node for dw-mipi-rockchip
drm/rockchip/dsi: remove mode_valid function
drm/rockchip/dsi: dw-mipi: correct the coding style
drm/rockchip/dsi: dw-mipi: support RK3399 mipi dsi
dt-bindings: add rk3399 support for dw-mipi-rockchip
drm/rockchip: dw-mipi-dsi: add reset control
drm/rockchip: dw-mipi-dsi: support non-burst modes
drm/rockchip: dw-mipi-dsi: defer probe if panel is not loaded
drm/rockchip: vop: test for P{H,V}SYNC
drm/rockchip: dw-mipi-dsi: use positive check for N{H, V}SYNC
drm/rockchip: dw-mipi-dsi: use specific poll helper
drm/rockchip: dw-mipi-dsi: improve PLL configuration
drm/rockchip: dw-mipi-dsi: properly configure PHY timing
...
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fixed the following style issues
drivers/gpu/vga/vga_switcheroo.c:98: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:99: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:102: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:103: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:129: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:135: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:217: WARNING: line over 80 characters
drivers/gpu/vga/vga_switcheroo.c:218: WARNING: line over 80 characters
drivers/gpu/vga/vga_switcheroo.c:308: WARNING: please, no space before tabs
drivers/gpu/vga/vga_switcheroo.c:340: WARNING: line over 80 characters
drivers/gpu/vga/vga_switcheroo.c:1087: WARNING: Block comments use * on subsequent lines
drivers/gpu/vga/vga_switcheroo.c:1087: WARNING: Block comments use a trailing */ on a separate line
Signed-off-by: Joan Jani <igiann@hotmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/HE1PR1001MB1148F38207BC31C860FAF06DC9560@HE1PR1001MB1148.EURPRD10.PROD.OUTLOOK.COM
We now pass the device to the debug messages, but on non-x86,
this is an invalid pointer in vga_arb_device_init:
drivers/gpu/vga/vgaarb.c: In function 'vga_arb_device_init':
drivers/gpu/vga/vgaarb.c:1467:4: error: 'dev' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This moves the initialization of the dev pointer outside of the
architecture #ifdef.
Fixes: a75d68f621 ("vgaarb: Use dev_printk() when possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161122143445.1896558-1-arnd@arndb.de
Use dev_printk() when possible. This makes messages more consistent with
other device-related messages and, in some cases, adds useful information.
This changes messages like this:
vgaarb: failed to allocate pci device
vgaarb: setting as boot device: PCI:0000:01:00.0
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: bridge control possible 0000:01:00.0
to this:
pci 0000:01:00.0: vgaarb: failed to allocate VGA arbiter data
pci 0000:01:00.0: vgaarb: setting as boot VGA device
pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
pci 0000:01:00.0: vgaarb: bridge control possible
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161117174758.16810.67625.stgit@bhelgaas-glaptop.roam.corp.google.com
Size of kmalloc() in vga_arb_write() is controlled by user.
Too large kmalloc() size triggers WARNING message on console.
Allocate the buffer on stack to avoid the WARNING.
The string must be small (e.g "target PCI:domain:bus:dev.fn").
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: syzkaller@googlegroups.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1476451342-146510-1-git-send-email-dvyukov@google.com
Move the documentation into Documentation/gpu, link it up and pull in
the kernel doc.
No actual text changes except that I did polish the kerneldoc a bit,
especially for vga_client_register().
v2: Remove some rst from vga-switcheroo.rst that I don't understand,
but which seems to be the reason why the new vgaarbiter.rst sometimes
drops out of the sidebar index.
v3: Drop one level of headings and clarify the vgaarb one a bit.
v4: Fix some typos (Sean).
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471034937-651-20-git-send-email-daniel.vetter@ffwll.ch
Daniel Vetter pointed out that vga_switcheroo_client_probe_defer() could
be needed by audio clients as well. To avoid mistakes when someone adds
conditions for these in the future, constrain the single existing
condition to VGA clients by checking for PCI_BASE_CLASS_DISPLAY. This
encompasses both PCI_CLASS_DISPLAY_VGA as well as PCI_CLASS_DISPLAY_3D,
which is used by some Nvidia Optimus GPUs.
Any future checks for audio clients should then be constrained to
PCI_BASE_CLASS_MULTIMEDIA.
v6: Spun out from commit introducing vga_switcheroo_client_probe_defer()
to keep it a pure refactoring change. (Emil Velikov, Jani Nikula)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/358d58490eb9dda5f270d844b0dce511a2a20828.1464685538.git.lukas@wunner.de
So far we've got one condition when DRM drivers need to defer probing
on a dual GPU system and it's coded separately into each of the relevant
drivers. As suggested by Daniel Vetter, deduplicate that code in the
drivers and move it to a new vga_switcheroo helper. This yields better
encapsulation of concepts and lets us add further checks in a central
place. (The existing check pertains to pre-retina MacBook Pros and an
additional check is expected to be needed for retinas.)
One might be tempted to check deferred probing conditions in
vga_switcheroo_register_client(), but this is usually called fairly late
during driver load. The GPU is fully brought up and ready for switching
at that point. On boot the ->probe hook is potentially called dozens of
times until it finally succeeds, and each time we'd repeat bringup and
teardown of the GPU, lengthening boot time considerably and cluttering
logfiles. A separate helper is therefore needed which can be called
right at the beginning of the ->probe hook.
Note that amdgpu currently does not call this helper as the AMD GPUs
built into MacBook Pros are only supported by radeon so far.
v2: This helper could eventually be used by audio clients as well,
so rephrase kerneldoc to refer to "client" instead of "GPU"
and move the single existing check in an if block specific
to PCI_CLASS_DISPLAY_VGA devices. Move documentation on
that check from kerneldoc to a comment. (Daniel Vetter)
v3: Mandate in kerneldoc that registration of client shall only
happen after calling this helper. (Daniel Vetter)
v4: Rebase on 412c8f7de0 ("drm/radeon: Return -EPROBE_DEFER when
amdkfd not loaded")
v5: Some Optimus GPUs use PCI_CLASS_DISPLAY_3D, make sure those are
matched as well. (Emil Velikov)
v6: The if-condition referring to PCI_BASE_CLASS_DISPLAY may be
considered a functional change. Move to a separate commit to
keep this a pure refactoring change. (Emil Velikov, Jani Nikula)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/575885fd440c2b13c3f19ddf44360cfbbff35f50.1464685538.git.lukas@wunner.de
Originally by Seth Forshee <seth.forshee@canonical.com>, 2012-10-04:
During graphics driver initialization it's useful to be able to mux
only the DDC to the inactive client in order to read the EDID. Add
a switch_ddc callback to allow capable handlers to provide this
functionality, and add vga_switcheroo_switch_ddc() to allow DRM
to mux only the DDC.
Modified by Dave Airlie <airlied@gmail.com>, 2012-12-22:
I can't figure out why I didn't like this, but I rewrote this [...]
to lock/unlock the ddc lines [...]. I think I'd prefer something
like that otherwise the interface got really ugly.
Modified by Lukas Wunner <lukas@wunner.de>, 2015-04 - 2015-10:
Change semantics of ->switch_ddc handler callback to return previous
DDC owner. Original version tried to determine previous DDC owner
with find_active_client() but this fails if the inactive client
registers before the active client.
Don't lock vgasr_mutex in _lock_ddc() / _unlock_ddc(), it can cause
deadlocks because (a) during switch (with vgasr_mutex already held),
GPU is woken and probes its outputs, tries to re-acquire vgasr_mutex
to lock DDC lines; (b) Likewise during switch, GPU is suspended and
calls cancel_delayed_work_sync() to stop output polling, if poll
task is running at this moment we may wait forever for it to finish.
Instead, lock mux_hw_lock when unregistering the handler because
the only reason why we'd want to lock vgasr_mutex in _lock_ddc() /
_unlock_ddc() is to block the handler from disappearing while DDC
lines are switched.
Also acquire mux_hw_lock in stage2 to avoid race condition where
reading the EDID and switching happens simultaneously. Likewise on
MIGD / MDIS commands and on runtime suspend.
v2.1: Overhaul locking, squash commits (Daniel Vetter)
v2.2: Readability improvements (Thierry Reding)
v2.3: Overhaul locking once more
v2.4: Retain semantics of ->switchto handler callback to switch all
pins, including DDC (Daniel Vetter)
v5: Rename ddc_lock to mux_hw_lock: Since we acquire this both
when calling ->switch_ddc and ->switchto, it protects not just
access to the DDC lines but to the mux in general. This is in
line with the DRM convention to use low-level locks to avoid
concurrent hw access (e.g. i2c, dp_aux) which are often called
hw_lock (Daniel Vetter)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61115
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/e81ae9722b84c5ed591805fee3ea6dbf5dc6c4b3.1452525860.git.lukas@wunner.de
Allow handlers to declare their capabilities and allow clients to
obtain that information. So far we have these use cases:
* If the handler is able to switch DDC separately, clients need to
probe EDID with drm_get_edid_switcheroo(). We should allow them
to detect a capable handler to ensure this function only gets
called when needed.
* Likewise if the handler is unable to switch AUX separately, the active
client needs to communicate link training parameters to the inactive
client, which may then skip the AUX handshake and set up its output
with these pre-calibrated values (DisplayPort specification v1.1a,
section 2.5.3.3). Clients need a way to recognize such a situation.
The flags for the radeon_atpx_handler and amdgpu_atpx_handler are
initially set to 0, this can later on be amended with
handler_flags |= VGA_SWITCHEROO_CAN_SWITCH_DDC;
when a ->switch_ddc callback is added.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61115
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/2b0d93ed6e511ca09e95e45e0b35627f330fabce.1452525860.git.lukas@wunner.de
Bjorn Helgaas