Satish reported a problem with the perm multicast router ports not getting
reenabled after some series of events, in particular if it happens that the
multicast snooping has been disabled and the port goes to disabled state
then it will be deleted from the router port list, but if it moves into
non-disabled state it will not be re-added because the mcast snooping is
still disabled, and enabling snooping later does nothing.
Here are the steps to reproduce, setup br0 with snooping enabled and eth1
added as a perm router (multicast_router = 2):
1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping
2. $ ip l set eth1 down
^ This step deletes the interface from the router list
3. $ ip l set eth1 up
^ This step does not add it again because mcast snooping is disabled
4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping
5. $ bridge -d -s mdb show
<empty>
At this point we have mcast enabled and eth1 as a perm router (value = 2)
but it is not in the router list which is incorrect.
After this change:
1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping
2. $ ip l set eth1 down
^ This step deletes the interface from the router list
3. $ ip l set eth1 up
^ This step does not add it again because mcast snooping is disabled
4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping
5. $ bridge -d -s mdb show
router ports on br0: eth1
Note: we can directly do br_multicast_enable_port for all because the
querier timer already has checks for the port state and will simply
expire if it's in blocking/disabled. See the comment added by
commit 9aa6638216 ("bridge: multicast: add a comment to
br_port_state_selection about blocking state")
Fixes: 561f1103a2 ("bridge: Add multicast_snooping sysfs toggle")
Reported-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I added the multicast flood control flag, I also added an attribute
for it for sysfs similar to other flags, but I forgot to add it to
brport_attrs.
Fixes: b6cb5ac833 ("net: bridge: add per-port multicast flood flag")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using bridge without bridge netfilter enabled the message
displayed is rather confusing and leads to belive that a deprecated
feature is in use. Use IS_MODULE to be explicit that the message only
affects users which use bridge netfilter as module and reword the
message.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/netfilter/core.c
net/netfilter/nf_tables_netdev.c
Resolve two conflicts before pull request for David's net-next tree:
1) Between c73c248490 ("netfilter: nf_tables_netdev: remove redundant
ip_hdr assignment") from the net tree and commit ddc8b6027a
("netfilter: introduce nft_set_pktinfo_{ipv4, ipv6}_validate()").
2) Between e8bffe0cf9 ("net: Add _nf_(un)register_hooks symbols") and
Aaron Conole's patches to replace list_head with single linked list.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
NFTA_LOG_FLAGS attribute is already supported, but the related
NF_LOG_XXX flags are not exposed to the userspace. So we cannot
explicitly enable log flags to log uid, tcp sequence, ip options
and so on, i.e. such rule "nft add rule filter output log uid"
is not supported yet.
So move NF_LOG_XXX macro definitions to the uapi/../nf_log.h. In
order to keep consistent with other modules, change NF_LOG_MASK to
refer to all supported log flags. On the other hand, add a new
NF_LOG_DEFAULT_MASK to refer to the original default log flags.
Finally, if user specify the unsupported log flags or NFTA_LOG_GROUP
and NFTA_LOG_FLAGS are set at the same time, report EINVAL to the
userspace.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The netfilter hook list never uses the prev pointer, and so can be trimmed to
be a simple singly-linked list.
In addition to having a more light weight structure for hook traversal,
struct net becomes 5568 bytes (down from 6400) and struct net_device becomes
2176 bytes (down from 2240).
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All of the callers of nf_hook_slow already hold the rcu_read_lock, so this
cleanup removes the recursive call. This is just a cleanup, as the locking
code gracefully handles this situation.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This replaces the last uses of NF_HOOK_THRESH().
Followup patch will remove it and rename nf_hook_thresh.
The reason is that inet (non-bridge) netfilter no longer invokes the
hooks from hooks, so we do no longer need the thresh value to skip hooks
with a lower priority.
The bridge netfilter however may need to do this. br_nf_hook_thresh is a
wrapper that is supposed to do this, i.e. only call hooks with a
priority that exceeds NF_BR_PRI_BRNF.
It's used only in the recursion cases of br_netfilter. It invokes
nf_hook_slow while holding an rcu read-side critical section to make a
future cleanup simpler.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If /sbin/bridge-stp is available on the system, bridge tries to execute
it instead of the kernel implementation when starting/stopping STP.
If anything goes wrong with /sbin/bridge-stp, bridge silently falls back
to kernel STP, making hard to debug userspace STP.
This patch adds a br_stp_call_user helper to start/stop userspace STP
and debug errors from the program: abnormal exit status is stored in the
lower byte and normal exit status is stored in higher byte.
Below is a simple example on a kernel with dynamic debug enabled:
# ln -s /bin/false /sbin/bridge-stp
# brctl stp br0 on
br0: failed to start userspace STP (256)
# dmesg
br0: /sbin/bridge-stp exited with code 1
br0: failed to start userspace STP (256)
br0: using kernel STP
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some codes of netfilter module which did not check the return
value of nft_register_chain_type. Add the checks now.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Consolidate pktinfo setup and validation by using the new generic
functions so we converge to the netdev family codebase.
We only need a linear IPv4 and IPv6 header from the reject expression,
so move nft_bridge_iphdr_validate() and nft_bridge_ip6hdr_validate()
to net/bridge/netfilter/nft_reject_bridge.c.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch introduces nft_set_pktinfo_unspec() that ensures proper
initialization all of pktinfo fields for non-IP traffic. This is used
by the bridge, netdev and arp families.
This new function relies on nft_set_pktinfo_proto_unspec() to set a new
tprot_set field that indicates if transport protocol information is
available. Remain fields are zeroed.
The meta expression has been also updated to check to tprot_set in first
place given that zero is a valid tprot value. Even a handcrafted packet
may come with the IPPROTO_RAW (255) protocol number so we can't rely on
this value as tprot unset.
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Most relevant updates are the removal of per-conntrack timers to
use a workqueue/garbage collection approach instead from Florian
Westphal, the hash and numgen expression for nf_tables from Laura
Garcia, updates on nf_tables hash set to honor the NLM_F_EXCL flag,
removal of ip_conntrack sysctl and many other incremental updates on our
Netfilter codebase.
More specifically, they are:
1) Retrieve only 4 bytes to fetch ports in case of non-linear skb
transport area in dccp, sctp, tcp, udp and udplite protocol
conntrackers, from Gao Feng.
2) Missing whitespace on error message in physdev match, from Hangbin Liu.
3) Skip redundant IPv4 checksum calculation in nf_dup_ipv4, from Liping Zhang.
4) Add nf_ct_expires() helper function and use it, from Florian Westphal.
5) Replace opencoded nf_ct_kill() call in IPVS conntrack support, also
from Florian.
6) Rename nf_tables set implementation to nft_set_{name}.c
7) Introduce the hash expression to allow arbitrary hashing of selector
concatenations, from Laura Garcia Liebana.
8) Remove ip_conntrack sysctl backward compatibility code, this code has
been around for long time already, and we have two interfaces to do
this already: nf_conntrack sysctl and ctnetlink.
9) Use nf_conntrack_get_ht() helper function whenever possible, instead
of opencoding fetch of hashtable pointer and size, patch from Liping Zhang.
10) Add quota expression for nf_tables.
11) Add number generator expression for nf_tables, this supports
incremental and random generators that can be combined with maps,
very useful for load balancing purpose, again from Laura Garcia Liebana.
12) Fix a typo in a debug message in FTP conntrack helper, from Colin Ian King.
13) Introduce a nft_chain_parse_hook() helper function to parse chain hook
configuration, this is used by a follow up patch to perform better chain
update validation.
14) Add rhashtable_lookup_get_insert_key() to rhashtable and use it from the
nft_set_hash implementation to honor the NLM_F_EXCL flag.
15) Missing nulls check in nf_conntrack from nf_conntrack_tuple_taken(),
patch from Florian Westphal.
16) Don't use the DYING bit to know if the conntrack event has been already
delivered, instead a state variable to track event re-delivery
states, also from Florian.
17) Remove the per-conntrack timer, use the workqueue approach that was
discussed during the NFWS, from Florian Westphal.
18) Use the netlink conntrack table dump path to kill stale entries,
again from Florian.
19) Add a garbage collector to get rid of stale conntracks, from
Florian.
20) Reschedule garbage collector if eviction rate is high.
21) Get rid of the __nf_ct_kill_acct() helper.
22) Use ARPHRD_ETHER instead of hardcoded 1 from ARP logger.
23) Make nf_log_set() interface assertive on unsupported families.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a per-port flag to control the unknown multicast flood, similar to the
unknown unicast flood flag and break a few long lines in the netlink flag
exports.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unicast flag and introduce an exact pkt_type. That would help us
for the upcoming per-port multicast flood flag and also slightly reduce the
tests in the input fast path.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fdb dumps spanning multiple skb's currently restart from the first
interface again for every skb. This results in unnecessary
iterations on the already visited interfaces and their fdb
entries. In large scale setups, we have seen this to slow
down fdb dumps considerably. On a system with 30k macs we
see fdb dumps spanning across more than 300 skbs.
To fix the problem, this patch replaces the existing single fdb
marker with three markers: netdev hash entries, netdevs and fdb
index to continue where we left off instead of restarting from the
first netdev. This is consistent with link dumps.
In the process of fixing the performance issue, this patch also
re-implements fix done by
commit 472681d57a ("net: ndo_fdb_dump should report -EMSGSIZE to rtnl_fdb_dump")
(with an internal fix from Wilson Kok) in the following ways:
- change ndo_fdb_dump handlers to return error code instead
of the last fdb index
- use cb->args strictly for dump frag markers and not error codes.
This is consistent with other dump functions.
Below results were taken on a system with 1000 netdevs
and 35085 fdb entries:
before patch:
$time bridge fdb show | wc -l
15065
real 1m11.791s
user 0m0.070s
sys 1m8.395s
(existing code does not return all macs)
after patch:
$time bridge fdb show | wc -l
35085
real 0m2.017s
user 0m0.113s
sys 0m1.942s
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull may fail due to various reasons (e.g. alloc failure), but the
skb isn't changed/dropped and processing continues so we shouldn't
increment tx_dropped.
CC: Kyeyoon Park <kyeyoonp@codeaurora.org>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Fixes: 958501163d ("bridge: Add support for IEEE 802.11 Proxy ARP")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bc8c20acae ("bridge: multicast: treat igmpv3 report with
INCLUDE and no sources as a leave") seems to have accidentally reverted
commit 47cc84ce0c ("bridge: fix parsing of MLDv2 reports"). This
commit brings back a change to br_ip6_multicast_mld2_report() where
parsing of MLDv2 reports stops when the first group is successfully
added to the MDB cache.
Fixes: bc8c20acae ("bridge: multicast: treat igmpv3 report with INCLUDE and no sources as a leave")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_log_set is an interface function, so it should do the strict sanity
check of parameters. Convert the return value of nf_log_set as int instead
of void. When the pf is invalid, return -EOPNOTSUPP.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of
port netdevs so that packets being flooded by the device won't be
flooded twice.
It works by assigning a unique identifier (the ifindex of the first
bridge port) to bridge ports sharing the same parent ID. This prevents
packets from being flooded twice by the same switch, but will flood
packets through bridge ports belonging to a different switch.
This method is problematic when stacked devices are taken into account,
such as VLANs. In such cases, a physical port netdev can have upper
devices being members in two different bridges, thus requiring two
different 'offload_fwd_mark's to be configured on the port netdev, which
is impossible.
The main problem is that packet and netdev marking is performed at the
physical netdev level, whereas flooding occurs between bridge ports,
which are not necessarily port netdevs.
Instead, packet and netdev marking should really be done in the bridge
driver with the switch driver only telling it which packets it already
forwarded. The bridge driver will mark such packets using the mark
assigned to the ingress bridge port and will prevent the packet from
being forwarded through any bridge port sharing the same mark (i.e.
having the same parent ID).
Remove the current switchdev 'offload_fwd_mark' implementation and
instead implement the proposed method. In addition, make rocker - the
sole user of the mark - use the proposed method.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I added support to export the vlan entry flags via xstats I forgot to
add support for the pvid since it is manually matched, so check if the
entry matches the vlan_group's pvid and set the flag appropriately.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bcf4934288 ("netfilter: ebtables: Fix extension lookup with
identical name") added a second lookup in case the extension that was
found during the first lookup matched another extension with the same
name, but didn't release the reference on the incorrect module.
Fixes: bcf4934288 ("netfilter: ebtables: Fix extension lookup with identical name")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
"meta pkttype set" is only supported on prerouting chain with bridge
family and ingress chain with netdev family.
But the validate check is incomplete, and the user can add the nft
rules on input chain with bridge family, for example:
# nft add table bridge filter
# nft add chain bridge filter input {type filter hook input \
priority 0 \;}
# nft add chain bridge filter test
# nft add rule bridge filter test meta pkttype set unicast
# nft add rule bridge filter input jump test
This patch fixes the problem.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use one of the vlan xstats padding fields to export the vlan flags. This is
needed in order to be able to distinguish between master (bridge) and port
vlan entries in user-space when dumping the bridge vlan stats.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the bridge driver we usually have the same function working for both
port and bridge. In order to follow that logic and also avoid code
duplication, consolidate the bridge_ and brport_ linkxstats calls into
one since they share most of their code. As a side effect this allows us
to dump the vlan stats also via the slave call which is in preparation for
the upcoming per-port vlan stats and vlan flag dumping.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding fdb entries pointing to the bridge device uses fdb_insert(),
which lacks various checks and does not respect added_by_user flag.
As a result, some inconsistent behavior can happen:
* Adding temporary entries succeeds but results in permanent entries.
* Same goes for "dynamic" and "use".
* Changing mac address of the bridge device causes deletion of
user-added entries.
* Replacing existing entries looks successful from userspace but actually
not, regardless of NLM_F_EXCL flag.
Use the same logic as other entries and fix them.
Fixes: 3741873b4f ("bridge: allow adding of fdb entries pointing to the bridge device")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8626c56c82 ("bridge: fix potential use-after-free when hook
returns QUEUE or STOLEN verdict") caused LLDP packets arriving through a
bridge port to be re-injected to the Rx path with skb->dev set to the
bridge device, but this breaks the lldpad daemon.
The lldpad daemon opens a packet socket with protocol set to ETH_P_LLDP
for any valid device on the system, which doesn't not include soft
devices such as bridge and VLAN.
Since packet sockets (ptype_base) are processed in the Rx path after the
Rx handler, LLDP packets with skb->dev set to the bridge device never
reach the lldpad daemon.
Fix this by making the bridge's Rx handler re-inject LLDP packets with
RX_HANDLER_PASS, which effectively restores the behaviour prior to the
mentioned commit.
This means netfilter will never receive LLDP packets coming through a
bridge port, as I don't see a way in which we can have okfn() consume
the packet without breaking existing behaviour. I've already carried out
a similar fix for STP packets in commit 56fae404fb ("bridge: Fix
incorrect re-injection of STP packets").
Fixes: 8626c56c82 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ageing_time type in br_set_ageing_time() from u32 to what it
is expected to be, i.e. a clock_t.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_stp_enable_bridge() does take the br->lock spinlock. Fix its wrongly
pasted comment and use the same as br_stp_disable_bridge().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch we had two flavors of most forwarding functions -
_forward and _deliver, the difference being that the latter are used
when the packets are locally originated. Instead of all this function
pointer passing and code duplication, we can just pass a boolean noting
that the packet was locally originated and use that to perform the
necessary checks in __br_forward. This gives a minor performance
improvement but more importantly consolidates the forwarding paths.
Also add a kernel doc comment to explain the exported br_forward()'s
arguments.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if the packet is going to be received locally we set skb0 or
sometimes called skb2 variables to the original skb. This can get
confusing and also we can avoid one conditional on the fast path by
simply using a boolean and passing it around. Thanks to Roopa for the
name suggestion.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes one conditional from the unicast path by using the fact
that skb is NULL only when the packet is multicast or is local.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial style changes in br_handle_frame_finish.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As was suggested this patch adds support for the different versions of MLD
and IGMP query types. Since the user visible structure is still in net-next
we can augment it instead of adding netlink attributes.
The distinction between the different IGMP/MLD query types is done as
suggested in Section 7.1, RFC 3376 [1] and Section 8.1, RFC 3810 [2] based
on query payload size and code for IGMP. Since all IGMP packets go through
multicast_rcv() and it uses ip_mc_check_igmp/ipv6_mc_check_mld we can be
sure that at least the ip/ipv6 header can be directly used.
[1] https://tools.ietf.org/html/rfc3376#section-7
[2] https://tools.ietf.org/html/rfc3810#section-8.1
Suggested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next,
they are:
1) Don't use userspace datatypes in bridge netfilter code, from
Tobin Harding.
2) Iterate only once over the expectation table when removing the
helper module, instead of once per-netns, from Florian Westphal.
3) Extra sanitization in xt_hook_ops_alloc() to return error in case
we ever pass zero hooks, xt_hook_ops_alloc():
4) Handle NFPROTO_INET from the logging core infrastructure, from
Liping Zhang.
5) Autoload loggers when TRACE target is used from rules, this doesn't
change the behaviour in case the user already selected nfnetlink_log
as preferred way to print tracing logs, also from Liping Zhang.
6) Conntrack slabs with SLAB_HWCACHE_ALIGN to allow rearranging fields
by cache lines, increases the size of entries in 11% per entry.
From Florian Westphal.
7) Skip zone comparison if CONFIG_NF_CONNTRACK_ZONES=n, from Florian.
8) Remove useless defensive check in nf_logger_find_get() from Shivani
Bhardwaj.
9) Remove zone extension as place it in the conntrack object, this is
always include in the hashing and we expect more intensive use of
zones since containers are in place. Also from Florian Westphal.
10) Owner match now works from any namespace, from Eric Bierdeman.
11) Make sure we only reply with TCP reset to TCP traffic from
nf_reject_ipv4, patch from Liping Zhang.
12) Introduce --nflog-size to indicate amount of network packet bytes
that are copied to userspace via log message, from Vishwanath Pai.
This obsoletes --nflog-range that has never worked, it was designed
to achieve this but it has never worked.
13) Introduce generic macros for nf_tables object generation masks.
14) Use generation mask in table, chain and set objects in nf_tables.
This allows fixes interferences with ongoing preparation phase of
the commit protocol and object listings going on at the same time.
This update is introduced in three patches, one per object.
15) Check if the object is active in the next generation for element
deactivation in the rbtree implementation, given that deactivation
happens from the commit phase path we have to observe the future
status of the object.
16) Support for deletion of just added elements in the hash set type.
17) Allow to resize hashtable from /proc entry, not only from the
obscure /sys entry that maps to the module parameter, from Florian
Westphal.
18) Get rid of NFT_BASECHAIN_DISABLED, this code is not exercised
anymore since we tear down the ruleset whenever the netdevice
goes away.
19) Support for matching inverted set lookups, from Arturo Borrero.
20) Simplify the iptables_mangle_hook() by removing a superfluous
extra branch.
21) Introduce ether_addr_equal_masked() and use it from the netfilter
codebase, from Joe Perches.
22) Remove references to "Use netfilter MARK value as routing key"
from the Netfilter Kconfig description given that this toggle
doesn't exists already for 10 years, from Moritz Sichert.
23) Introduce generic NF_INVF() and use it from the xtables codebase,
from Joe Perches.
24) Setting logger to NONE via /proc was not working unless explicit
nul-termination was included in the string. This fixes seems to
leave the former behaviour there, so we don't break backward.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
L2 upper device needs to propagate neigh_construct/destroy calls down to
lower devices. Do this by defining default ndo functions and use them in
team, bond, bridge and vlan.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter uses multiple FWINV #defines with identical form that hide a
specific structure variable and dereference it with a invflags member.
$ git grep "#define FWINV"
include/linux/netfilter_bridge/ebtables.h:#define FWINV(bool,invflg) ((bool) ^ !!(info->invflags & invflg))
net/bridge/netfilter/ebtables.c:#define FWINV2(bool, invflg) ((bool) ^ !!(e->invflags & invflg))
net/ipv4/netfilter/arp_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(arpinfo->invflags & (invflg)))
net/ipv4/netfilter/ip_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(ipinfo->invflags & (invflg)))
net/ipv6/netfilter/ip6_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(ip6info->invflags & (invflg)))
net/netfilter/xt_tcpudp.c:#define FWINVTCP(bool, invflg) ((bool) ^ !!(tcpinfo->invflags & (invflg)))
Consolidate these macros into a single NF_INVF macro.
Miscellanea:
o Neaten the alignment around these uses
o A few lines are > 80 columns for intelligibility
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There are code duplications of a masked ethernet address comparison here
so make it a separate function instead.
Miscellanea:
o Neaten alignment of FWINV macro uses to make it clearer for the reader
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ip_skb_dst_mtu uses skb->sk, assuming it is an AF_INET socket (e.g. it
calls ip_sk_use_pmtu which casts sk as an inet_sk).
However, in the case of UDP tunneling, the skb->sk is not necessarily an
inet socket (could be AF_PACKET socket, or AF_UNSPEC if arriving from
tun/tap).
OTOH, the sk passed as an argument throughout IP stack's output path is
the one which is of PMTU interest:
- In case of local sockets, sk is same as skb->sk;
- In case of a udp tunnel, sk is the tunneling socket.
Fix, by passing ip_finish_output's sk to ip_skb_dst_mtu.
This augments 7026b1ddb6 'netfilter: Pass socket pointer down through okfn().'
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds stats support for the currently used IGMP/MLD types by the
bridge. The stats are per-port (plus one stat per-bridge) and per-direction
(RX/TX). The stats are exported via netlink via the new linkxstats API
(RTM_GETSTATS). In order to minimize the performance impact, a new option
is used to enable/disable the stats - multicast_stats_enabled, similar to
the recent vlan stats. Also in order to avoid multiple IGMP/MLD type
lookups and checks, we make use of the current "igmp" member of the bridge
private skb->cb region to record the type on Rx (both host-generated and
external packets pass by multicast_rcv()). We can do that since the igmp
member was used as a boolean and all the valid IGMP/MLD types are positive
values. The normal bridge fast-path is not affected at all, the only
affected paths are the flooding ones and since we make use of the IGMP/MLD
type, we can quickly determine if the packet should be counted using
cache-hot data (cb's igmp member). We add counters for:
* IGMP Queries
* IGMP Leaves
* IGMP v1/v2/v3 reports
* MLD Queries
* MLD Leaves
* MLD v1/v2 reports
These are invaluable when monitoring or debugging complex multicast setups
with bridges.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the IFLA_STATS_LINK_XSTATS_SLAVE attribute
which allows to export per-slave statistics if the master device supports
the linkxstats callback. The attribute is passed down to the linkxstats
callback and it is up to the callback user to use it (an example has been
added to the only current user - the bridge). This allows us to query only
specific slaves of master devices like bridge ports and export only what
we're interested in instead of having to dump all ports and searching only
for a single one. This will be used to export per-port IGMP/MLD stats and
also per-port vlan stats in the future, possibly other statistics as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I made a dumb off-by-one mistake when I added the vlan stats counter
dumping code. The increment should happen before the check, not after
otherwise we miss one entry when we continue dumping.
Fixes: a60c090361 ("bridge: netlink: export per-vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge is falsly dropping ipv6 mulitcast packets if there is:
1. No ipv6 address assigned on the brigde.
2. No external mld querier present.
3. The internal querier enabled.
When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.
Ipv6 multicast snooping can only work if:
a) An external querier is present
OR
b) The bridge has an ipv6 address an is capable of sending own queries
Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.
This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().
Special thanks to Linus Lüssing.
Fixes: d1d81d4c3d ("bridge: check return value of ipv6_dev_get_saddr()")
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8626c56c82 ("bridge: fix potential use-after-free when hook
returns QUEUE or STOLEN verdict") fixed incorrect usage of NF_HOOK's
return value by consuming packets in okfn via br_pass_frame_up().
However, this function re-injects packets to the Rx path with skb->dev
set to the bridge device, which breaks kernel's STP, as all STP packets
appear to originate from the bridge device itself.
Instead, if STP is enabled and bridge isn't a 802.1ad bridge, then learn
packet's SMAC and inject it back to the Rx path for further processing
by the packet handlers.
The patch also makes netfilter's behavior consistent with regards to
packets destined to the Bridge Group Address, as no hook registered at
LOCAL_IN will ever be called, regardless if STP is enabled or not.
Cc: Florian Westphal <fw@strlen.de>
Cc: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Fixes: 8626c56c82 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The missing br_vlan_should_use() test caused creation of an unneeded
local fdb entry on changing mac address of a bridge device when there is
a vlan which is configured on a bridge port but not on the bridge
device.
Fixes: 2594e9064a ("bridge: vlan: add per-vlan struct and move to rhashtables")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch produces data type 'checks'.
This patch amends them by changing, for example:
uint8_t -> u8
Signed-off-by: Tobin C Harding <me@tobin.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the newly introduced helper functions the skb pulling is hidden
in the checksumming function - and undone before returning to the
caller.
The IGMP and MLD query parsing functions in the bridge still
assumed that the skb is pointing to the beginning of the IGMP/MLD
message while it is now kept at the beginning of the IPv4/6 header.
If there is a querier somewhere else, then this either causes
the multicast snooping to stay disabled even though it could be
enabled. Or, if we have the querier enabled too, then this can
create unnecessary IGMP / MLD query messages on the link.
Fixing this by taking the offset between IP and IGMP/MLD header into
account, too.
Fixes: 9afd85c9e4 ("net: Export IGMP/MLD message validation code")
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov