radeon fixes for 3.17, kind of all over the place (dpm, GPUVM, etc.)
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Remove duplicate include from Makefile
drm/radeon/dpm: select the appropriate vce power state for KV/KB/ML
drm/radeon: Add ability to get and change dpm state when radeon PX card is turned off
drm/radeon: Add missing lines to ci_set_thermal_temperature_range
drm/radeon: Always flush VM again on < CIK
drm/radeon: add a check for allocation failure (v2)
drm/radeon: use pfp for all vm_flush related updates
drm/radeon: add bapm module parameter
Make sure the cursor gets fully clipped when enabling it on a disabled
crtc via setplane. This will prevent the lower level code from
attempting to enable the cursor in hardware.
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
During suspend we turn off the crtcs, but leave the staged config in
place so that we can restore the display(s) to their previous state on
resume.
During resume when we attempt to apply the force pipe A quirk we use the
load detect mechanism. That doesn't check whether there was an already
staged configuration for the crtc since that's not even possible during
normal runtime load detection. But during resume it is possible, and if
we just blindly go and overwrite the staged crtc configuration for the
load detection we can no longer restore the display to the correct
state.
Even worse, we don't even clear all the staged connector->encoder->crtc
links so we may end up using a cloned setup for the load detection, and
after we're done we just clear the links related to the VGA output
leaving the links for the other outputs in place. This will eventually
result in calling intel_set_mode() with mode==NULL but with valid
connector->encoder->crtc links which will result in dereferencing the
NULL mode since the code thinks it will have to a modeset.
To avoid these problems don't use any crtc with new_enabled==true for
load detection.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org (for 3.16)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
intel_enable_pipe_a() gets called with all the modeset locks already
held (by drm_modeset_lock_all()), so trying to grab the same
locks using another drm_modeset_acquire_ctx is going to fail miserably.
Move most of the drm_modeset_acquire_ctx handling (init/drop/fini)
out from intel_{get,release}_load_detect_pipe() into the callers
(intel_{crt,tv}_detect()). Only the actual locking and backoff
handling is left in intel_get_load_detect_pipe(). And in
intel_enable_pipe_a() we just share the mode_config.acquire_ctx from
drm_modeset_lock_all() which is already holding all the relevant locks.
It's perfectly legal to lock the same ww_mutex multiple times using the
same ww_acquire_ctx. drm_modeset_lock() will convert the returned
-EALREADY into 0, so the caller doesn't need to do antyhing special.
Fixes a hang on resume on my 830.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Pull drm fixes (mostly nouveau) from Dave Airlie:
"One doc buidling fixes for a file that moved, along with a bunch of
nouveau fixes, one a build problem on ARM"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/doc: Refer to proper source file
drm/nouveau/platform: fix compilation error
drm/nouveau/gk20a: add LTC device
drm/nouveau: warn if we fail to re-pin fb on resume
drm/nouveau/nvif: fix dac load detect method definition
drm/gf100-/gr: fix -ENOSPC detection when allocating zbc table entries
drm/nouveau/nvif: return null pointers on failure, in addition to ret != 0
drm/nouveau/ltc: fix tag base address getting truncated if above 4GiB
drm/nvc0-/fb/ram: fix use of non-existant ram if partitions aren't uniform
drm/nouveau/bar: behave better if ioremap failed
drm/nouveau/kms: nouveau_fbcon_accel_fini can be static
drm/nouveau: kill unused variable warning if !__OS_HAS_AGP
drm/nouveau/nvif: fix a number of notify thinkos
In the Makefile, radeon_uvd.o is added to radeon-y twice.
As it belongs to the UVD block marked with a comment, the other include
from the block of includes labelled as "KMS driver" is deleted.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Compare the clock in the limits table to the requested evclk rather
than just taking the first value. Improves vce performance in certain
cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Properly set the thermal min and max temp on CI.
Otherwise, we end up setting the thermal ranges
to 0 on resume and end up in the lowest power state.
Signed-off-by: Oleg Chernovskiy <algonkvel@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Not doing this causes piglit hangs[0] on my Cape Verde card. No issues on
Bonaire and Kaveri though.
[0] Same symptoms as those fixed on CIK by 'drm/radeon: set VM base addr
using the PFP v2'.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can easily return -ENOMEM here if kzalloc() fails.
v2: agd5f: drop the vm mutex
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a module paramter to enable bapm on APUs. It's disabled
by default on certain APUs due to stability issues. This
option makes it easier to test and to enable it on systems that
are stable.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=81021
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
A couple of thinkos from the -next merge, some random fixes from a
coverity scan, fix for (at least) GK106 accidentally using
non-existent vram on some board configurations, and better behaviour
of the instmem allocations if vmalloc space runs out.
* 'linux-3.17' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/platform: fix compilation error
drm/nouveau/gk20a: add LTC device
drm/nouveau: warn if we fail to re-pin fb on resume
drm/nouveau/nvif: fix dac load detect method definition
drm/gf100-/gr: fix -ENOSPC detection when allocating zbc table entries
drm/nouveau/nvif: return null pointers on failure, in addition to ret != 0
drm/nouveau/ltc: fix tag base address getting truncated if above 4GiB
drm/nvc0-/fb/ram: fix use of non-existant ram if partitions aren't uniform
drm/nouveau/bar: behave better if ioremap failed
drm/nouveau/kms: nouveau_fbcon_accel_fini can be static
drm/nouveau: kill unused variable warning if !__OS_HAS_AGP
drm/nouveau/nvif: fix a number of notify thinkos
nouveau_platform.c was still using the old nouveau_dev() macro,
triggering a compilation error. Fix this.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
LTC device is now required for PGRAPH to work, add it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported by Coverity. The intention is that the return value is
checked, but let's be more paranoid and make it extremely obvious
if something forgets to.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Static analysers find it 'suspicious', that we're trying to allocate memory for
elements of size sizeof(struct drm_fb_helper_connector) when the array is
defined as struct drm_fb_helper_connector **.
Use sizeof(struct drm_fb_helper_connector *) instead.
Note that the structure being defined as:
struct drm_fb_helper_connector {
struct drm_connector *connector;
};
This was still doing the right thing, but may not in the future if
additional fields are added.
Cc: Todd Previte <tprevite@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Static analysis will be unhappy if a function can theoretically return
0 and we're trying to divide by that value.
Mark that case that cannot occur as a BUG() instead.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bunch of small leftovers spotted by looking at the make htmldocs output.
I've left out dp mst, there's too much amiss there.
v2: Also add the missing parameter docbook in the dp mst code - Dave
Airlie correctly pointed out that we don't actually want kerneldoc for
the missing structure members in header files.
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It needs to be anonymous memory (no file mappings)
and we are requried to install an MMU notifier.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Whenever userspace mapping related to our userptr change
we wait for it to become idle and unmap it from GTT.
v2: rebased, fix mutex unlock in error path
v3: improve commit message
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This way we test userptr availability at BO creation time instead of first use.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoid problems with writeback by limiting userptr to anonymous memory.
v2: add commit and code comments
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds an IOCTL for turning a pointer supplied by
userspace into a buffer object.
It imposes several restrictions upon the memory being mapped:
1. It must be page aligned (both start/end addresses, i.e ptr and size).
2. It must be normal system memory, not a pointer into another map of IO
space (e.g. it must not be a GTT mmapping of another object).
3. The BO is mapped into GTT, so the maximum amount of memory mapped at
all times is still the GTT limit.
4. The BO is only mapped readonly for now, so no write support.
5. List of backing pages is only acquired once, so they represent a
snapshot of the first use.
Exporting and sharing as well as mapping of buffer objects created by
this function is forbidden and results in an -EPERM.
v2: squash all previous changes into first public version
v3: fix tabs, map readonly, don't use MM callback any more
v4: set TTM_PAGE_FLAG_SG so that TTM never messes with the pages,
pin/unpin pages on bind/unbind instead of populate/unpopulate
v5: rebased on 3.17-wip, IOCTL renamed to userptr, reject any unknown
flags, better handle READONLY flag, improve permission check
v6: fix ptr cast warning, use set_page_dirty/mark_page_accessed on unpin
v7: add warning about it's availability in the API definition
v8: drop access_ok check, fix VM mapping bits
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v4)
Reviewed-by: Jérôme Glisse <jglisse@redhat.com> (v4)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As usual in both a crtc index and a struct drm_crtc * version.
The function assumes that no one drivers their display below 10Hz, and
it will complain if the vblank wait takes longer than that.
v2: Also check dev->max_vblank_counter since some drivers register a
fake get_vblank_counter function.
v3: Use drm_vblank_count instead of calling the low-level
->get_vblank_counter callback. That way we'll get the sw-cooked
counter for platforms without proper vblank support and so can ditch
the max_vblank_counter check again.
v4: Review from Michel Dänzer:
- Restore lost notes about v3:
- Spelling in kerneldoc.
- Inline wait_event condition.
- s/vblank_wait/wait_one_vblank/
Cc: Michel Dänzer <michel@daenzer.net>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In general having this can't hurt, and the atomic helpers will need
it to be able to reset the state objects properly. The overall idea
is to reset in the order pixels flow, so planes -> crtcs ->
encoders -> connectors.
v2: Squash in fixup from Ville to correctly deference struct drm_plane
instead of drm_crtc when walking the plane list. Fixes an oops in
driver init and resume.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull nouveau drm updates from Ben Skeggs:
"Apologies for not getting this done in time for Dave's drm-next merge
window. As he mentioned, a pre-existing bug reared its head a lot
more obviously after this lot of changes. It took quite a bit of time
to track it down. In any case, Dave suggested I try my luck by
sending directly to you this time.
Overview:
- more code for Tegra GK20A from NVIDIA - probing, reclockig
- better fix for Kepler GPUs that have the graphics engine powered
off on startup, method courtesy of info provided by NVIDIA
- unhardcoding of a bunch of graphics engine setup on
Fermi/Kepler/Maxwell, will hopefully solve some issues people have
noticed on higher-end models
- support for "Zero Bandwidth Clear" on Fermi/Kepler/Maxwell, needs
userspace support in general, but some lucky apps will benefit
automagically
- reviewed/exposed the full object APIs to userspace (finally), gives
it access to perfctrs, ZBC controls, various events. More to come
in the future.
- various other fixes"
Acked-by: Dave Airlie <airlied@redhat.com>
* 'linux-3.17' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (87 commits)
drm/nouveau: expose the full object/event interfaces to userspace
drm/nouveau: fix headless mode
drm/nouveau: hide sysfs pstate file behind an option again
drm/nv50/disp: shhh compiler
drm/gf100-/gr: implement the proper SetShaderExceptions method
drm/gf100-/gr: remove some broken ltc bashing, for now
drm/gf100-/gr: unhardcode attribute cb config
drm/gf100-/gr: fetch tpcs-per-ppc info on startup
drm/gf100-/gr: unhardcode pagepool config
drm/gf100-/gr: unhardcode bundle cb config
drm/gf100-/gr: improve initial context patch list helpers
drm/gf100-/gr: add support for zero bandwidth clear
drm/nouveau/ltc: add zbc drivers
drm/nouveau/ltc: s/ltcg/ltc/ + cleanup
drm/nouveau: use ram info from nvif_device
drm/nouveau/disp: implement nvif event sources for vblank/connector notifiers
drm/nouveau/disp: allow user direct access to channel control registers
drm/nouveau/disp: audit and version display classes
drm/nouveau/disp: audit and version SCANOUTPOS method
drm/nv50-/disp: audit and version PIOR_PWR method
...
No-one has yet had time to move this to debugfs as discussed during
the last merge window. Until this happens, hide the option to make
it clear it's not going to be here forever.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We have another version of it implemented in SW, however, that version
isn't serialised with normal PGRAPH operation and can possibly clobber
the enables for another context.
This is the same method that's implemented by the NVIDIA binary driver.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
... and hope that the defaults are good enough. This was always
supposed to be a read/modify/write thing anyway, so we're writing
very wrong stuff for some boards already.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Should be the same values as before, except:
GF117 has smaller buffer allocated, as per register setup.
GK20A now uses values from Tegra driver, not GK104's.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Removes need for fixed buffer indices, and allows the functions
utilising them to also be run outside of context generation.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Default ZBC table is compatible with binary driver defaults.
Userspace will need to be updated to take full advantage of this
feature, however, some applications will see a performance boost
without updated drivers.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
One of the next commits will remove some of the class IDs, leaving only
the ones used by NVIDIA which, presumably, mark where functionality
changes actually happened.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The indirect method has been left in-place here as a fallback path, as
it may not be possible to map the non-PAGE_SIZE aligned control areas
across some chipset+interface combinations.
This isn't a problem for the primary use-case where the core and drm
are linked together in kernel-land, but across a VM or (in the case
where it applies now) between the core in the kernel and a userspace
test tool.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The full object interfaces are about to be exposed to userspace, so we
need to check for any security-related issues and version the structs
to make it easier to handle any changes we may need in the future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is a wrapper around the interfaces defined in an earlier commit,
and is also used by various userspace (either by a libdrm backend, or
libpciaccess) tools/tests.
In the future this will be extended to handle channels, replacing some
long-unloved code we currently use, and allow fifo/display/mpeg (hi
Ilia ;)) engines to all be exposed in the same way.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This forms the basis for the new APIs that will be exposed to userspace,
giving it access to:
- Object method calls, the immediately useful of which is performance
counters and the abiity to manipulate the ZBC tables.
- Information on the child classes an object supports, in order to avoid
having to try all supported classes until successful.
- Notifications, which will be used in the future to inform the client
if its channel was killed due to a lockup, etc.
This commit imports the interfaces, but are not currently used. The DRM
portion of the driver will be ported to speak to the core using these
interfaces as much as possible.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is a lot of prep-work for being able to send event notifications
back to userspace. Events now contain data, rather than a "something
just happened" signal.
Handler data is now embedded into a containing structure, rather than
being kmalloc()'d, and can optionally have the notify routine handled
in a workqueue.
Various races between suspend/unload with display HPD/DP IRQ handlers
automagically solved as a result.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Linux 3.16 fixed multiple bugs in kms pageflip completion events
and timestamping, which were originally introduced in Linux 3.13.
These fixes have been backported to all stable kernels since 3.13.
However, the userspace nouveau-ddx needs to be aware if it is
running on a kernel on which these bugs are fixed, or not.
Bump the patchlevel of the drm driver version to signal this,
so backporting this patch to stable 3.13+ kernels will give the
ddx the required info.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org> #v3.13+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Dave Airlie