Meta has instructions for accessing:
- bytes - GETB (1 byte)
- words - GETW (2 bytes)
- doublewords - GETD (4 bytes)
- longwords - GETL (8 bytes)
All accesses must be aligned. Unaligned accesses can be detected and
made to fault on Meta2, however it isn't possible to fix up unaligned
writes so we don't bother fixing up reads either.
This patch adds metag memory handling code including:
- I/O memory (io.h, ioremap.c): Actually any virtual memory can be
accessed with these helpers. A part of the non-MMUable address space
is used for memory mapped I/O. The ioremap() function is implemented
one to one for non-MMUable addresses.
- User memory (uaccess.h, usercopy.c): User memory is directly
accessible from privileged code.
- Kernel memory (maccess.c): probe_kernel_write() needs to be
overwridden to use the I/O functions when doing a simple aligned
write to non-writecombined memory, otherwise the write may be split
by the generic version.
Note that due to the fact that a portion of the virtual address space is
non-MMUable, and therefore always maps directly to the physical address
space, metag specific I/O functions are made available (metag_in32,
metag_out32 etc). These cast the address argument to a pointer so that
they can be used with raw physical addresses. These accessors are only
to be used for accessing fixed core Meta architecture registers in the
non-MMU region, and not for any SoC/peripheral registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Add memory management files for metag.
Meta's 32bit virtual address space is split into two halves:
- local (0x08000000-0x7fffffff): traditionally local to a hardware
thread and incoherent between hardware threads. Each hardware thread
has it's own local MMU table. On Meta2 the local space can be
globally coherent (GCOn) if the cache partitions coincide.
- global (0x88000000-0xffff0000): coherent and traditionally global
between hardware threads. On Meta2, each hardware thread has it's own
global MMU table.
The low 128MiB of each half is non-MMUable and maps directly to the
physical address space:
- 0x00010000-0x07ffffff: contains Meta core registers and maps SoC bus
- 0x80000000-0x87ffffff: contains low latency global core memories
Linux usually further splits the local virtual address space like this:
- 0x08000000-0x3fffffff: user mappings
- 0x40000000-0x7fffffff: kernel mappings
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Add cache and TLB handling code for metag, including the required
callbacks used by MM switches and DMA operations. Caches can be
partitioned between the hardware threads and the global space, however
this is usually configured by the bootloader so Linux doesn't make any
changes to this configuration. TLBs aren't configurable, so only need
consideration to flush them.
On Meta1 the L1 cache was VIVT which required a full flush on MM switch.
Meta2 has a VIPT L1 cache so it doesn't require the full flush on MM
switch. Meta2 can also have a writeback L2 with hardware prefetch which
requires some special handling. Support is optional, and the L2 can be
detected and initialised by Linux.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Add source files from the Thread Binary Interface (TBI) library which
provides useful low level operations and traps/context management.
Among other things it handles interrupt/exception/syscall entry (in
tbipcx.S).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Add the main header for the Thread Binary Interface (TBI) library which
provides useful low level operations and trap/context management.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Add boot code for metag. Due to the multi-threaded nature of Meta it is
not uncommon for an RTOS or bare metal application to be started on
other hardware threads by the bootloader. Since there is a single MMU
switch which affects all threads, the MMU is traditionally configured by
the bootloader prior to starting Linux. The bootloader passes a
structure to Linux which among other things contains information about
memory regions which have been mapped. Linux then assumes control of the
local heap memory region.
A kernel arguments string pointer or a flattened device tree pointer can
be provided in the third argument.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Add the header <asm/metag_mem.h> describing addresses, fields, and bits
of various core memory mapped registers in the low non-MMU region.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Add a couple of header files containing core architecture constants.
The first (<asm/metag_isa.h>) contains some constants relating to the
instruction set, such as values to give to the CACHEW and CACHER
instructions.
The second (<asm/metag_regs.h>) contains constants for the core register
units directly accessible to various instructions, and for the
registers, fields, and bits in those units. The main units described are
the control unit (CT.*), the trigger unit (TR.*), and the run-time trace
unit (TT.*).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
On 64 bit architectures with no efficient unaligned access, padding and
explicit alignment must be added in various places to prevent unaligned
64bit accesses (such as taskstats and trace ring buffer).
However this also needs to apply to 32 bit architectures with 64 bit
accesses requiring alignment such as metag.
This is solved by adding a new Kconfig symbol HAVE_64BIT_ALIGNED_ACCESS
which defaults to 64BIT && !HAVE_EFFICIENT_UNALIGNED_ACCESS, and can be
explicitly selected by METAG and any other relevant architectures. This
can be used in various places to determine whether 64bit alignment is
required.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: Will Drewry <wad@chromium.org>
commit e72837e3e7 introduced
a default SET_PERSONALITY() in include/linux/elf.h.
This breaks with our own SET_PERSONALITY define for
32bit userspace on 64bit kernel.
Signed-off-by: Helge Deller <deller@gmx.de>
PA-RISC is the only arch that installs the modules when installing the kernel.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Helge Deller <deller@gmx.de>
This fixes compile warnings like this one:
net/ipv4/igmp.c: In function ‘ip_mc_leave_group’:
net/ipv4/igmp.c:1898:3: warning: overflow in implicit constant conversion [-Woverflow]
atomic_sub() is defined as __atomic_add_return(-(VAL),(v))))
and if VAL is of type unsigned int (as returned by sizeof()), negating
this value will overflow. Fix this by type-casting VAL to int type.
Signed-off-by: Helge Deller <deller@gmx.de>
Avoid this warning, while still prevent gcc from optimizing away the exception code:
arch/parisc/lib/memcpy.c: In function ‘pa_memcpy’:
arch/parisc/lib/memcpy.c:256:2: warning: ‘dummy’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Helge Deller <deller@gmx.de>
Tim found:
WARNING: at arch/x86/kernel/smpboot.c:324 topology_sane.isra.2+0x6f/0x80()
Hardware name: S2600CP
sched: CPU #1's llc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency.
smpboot: Booting Node 1, Processors #1
Modules linked in:
Pid: 0, comm: swapper/1 Not tainted 3.9.0-0-generic #1
Call Trace:
set_cpu_sibling_map+0x279/0x449
start_secondary+0x11d/0x1e5
Don Morris reproduced on a HP z620 workstation, and bisected it to
commit e8d1955258 ("acpi, memory-hotplug: parse SRAT before memblock
is ready")
It turns out movable_map has some problems, and it breaks several things
1. numa_init is called several times, NOT just for srat. so those
nodes_clear(numa_nodes_parsed)
memset(&numa_meminfo, 0, sizeof(numa_meminfo))
can not be just removed. Need to consider sequence is: numaq, srat, amd, dummy.
and make fall back path working.
2. simply split acpi_numa_init to early_parse_srat.
a. that early_parse_srat is NOT called for ia64, so you break ia64.
b. for (i = 0; i < MAX_LOCAL_APIC; i++)
set_apicid_to_node(i, NUMA_NO_NODE)
still left in numa_init. So it will just clear result from early_parse_srat.
it should be moved before that....
c. it breaks ACPI_TABLE_OVERIDE...as the acpi table scan is moved
early before override from INITRD is settled.
3. that patch TITLE is total misleading, there is NO x86 in the title,
but it changes critical x86 code. It caused x86 guys did not
pay attention to find the problem early. Those patches really should
be routed via tip/x86/mm.
4. after that commit, following range can not use movable ram:
a. real_mode code.... well..funny, legacy Node0 [0,1M) could be hot-removed?
b. initrd... it will be freed after booting, so it could be on movable...
c. crashkernel for kdump...: looks like we can not put kdump kernel above 4G
anymore.
d. init_mem_mapping: can not put page table high anymore.
e. initmem_init: vmemmap can not be high local node anymore. That is
not good.
If node is hotplugable, the mem related range like page table and
vmemmap could be on the that node without problem and should be on that
node.
We have workaround patch that could fix some problems, but some can not
be fixed.
So just remove that offending commit and related ones including:
f7210e6c4a ("mm/memblock.c: use CONFIG_HAVE_MEMBLOCK_NODE_MAP to
protect movablecore_map in memblock_overlaps_region().")
01a178a94e ("acpi, memory-hotplug: support getting hotplug info from
SRAT")
27168d38fa ("acpi, memory-hotplug: extend movablemem_map ranges to
the end of node")
e8d1955258 ("acpi, memory-hotplug: parse SRAT before memblock is
ready")
fb06bc8e5f ("page_alloc: bootmem limit with movablecore_map")
42f47e27e7 ("page_alloc: make movablemem_map have higher priority")
6981ec3114 ("page_alloc: introduce zone_movable_limit[] to keep
movable limit for nodes")
34b71f1e04 ("page_alloc: add movable_memmap kernel parameter")
4d59a75125 ("x86: get pg_data_t's memory from other node")
Later we should have patches that will make sure kernel put page table
and vmemmap on local node ram instead of push them down to node0. Also
need to find way to put other kernel used ram to local node ram.
Reported-by: Tim Gardner <tim.gardner@canonical.com>
Reported-by: Don Morris <don.morris@hp.com>
Bisected-by: Don Morris <don.morris@hp.com>
Tested-by: Don Morris <don.morris@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull signal/compat fixes from Al Viro:
"Fixes for several regressions introduced in the last signal.git pile,
along with fixing bugs in truncate and ftruncate compat (on just about
anything biarch at least one of those two had been done wrong)."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
compat: restore timerfd settime and gettime compat syscalls
[regression] braino in "sparc: convert to ksignal"
fix compat truncate/ftruncate
switch lseek to COMPAT_SYSCALL_DEFINE
lseek() and truncate() on sparc really need sign extension
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NKkW
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.9-rc1-late' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull new ARC architecture from Vineet Gupta:
"Initial ARC Linux port with some fixes on top for 3.9-rc1:
I would like to introduce the Linux port to ARC Processors (from
Synopsys) for 3.9-rc1. The patch-set has been discussed on the public
lists since Nov and has received a fair bit of review, specially from
Arnd, tglx, Al and other subsystem maintainers for DeviceTree, kgdb...
The arch bits are in arch/arc, some asm-generic changes (acked by
Arnd), a minor change to PARISC (acked by Helge).
The series is a touch bigger for a new port for 2 main reasons:
1. It enables a basic kernel in first sub-series and adds
ptrace/kgdb/.. later
2. Some of the fallout of review (DeviceTree support, multi-platform-
image support) were added on top of orig series, primarily to
record the revision history.
This updated pull request additionally contains
- fixes due to our GNU tools catching up with the new syscall/ptrace
ABI
- some (minor) cross-arch Kconfig updates."
* tag 'arc-v3.9-rc1-late' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (82 commits)
ARC: split elf.h into uapi and export it for userspace
ARC: Fixup the current ABI version
ARC: gdbserver using regset interface possibly broken
ARC: Kconfig cleanup tracking cross-arch Kconfig pruning in merge window
ARC: make a copy of flat DT
ARC: [plat-arcfpga] DT arc-uart bindings change: "baud" => "current-speed"
ARC: Ensure CONFIG_VIRT_TO_BUS is not enabled
ARC: Fix pt_orig_r8 access
ARC: [3.9] Fallout of hlist iterator update
ARC: 64bit RTSC timestamp hardware issue
ARC: Don't fiddle with non-existent caches
ARC: Add self to MAINTAINERS
ARC: Provide a default serial.h for uart drivers needing BASE_BAUD
ARC: [plat-arcfpga] defconfig for fully loaded ARC Linux
ARC: [Review] Multi-platform image #8: platform registers SMP callbacks
ARC: [Review] Multi-platform image #7: SMP common code to use callbacks
ARC: [Review] Multi-platform image #6: cpu-to-dma-addr optional
ARC: [Review] Multi-platform image #5: NR_IRQS defined by ARC core
ARC: [Review] Multi-platform image #4: Isolate platform headers
ARC: [Review] Multi-platform image #3: switch to board callback
...
Pull MIPS updates from Ralf Baechle:
o Add basic support for the Mediatek/Ralink Wireless SoC family.
o The Qualcomm Atheros platform is extended by support for the new
QCA955X SoC series as well as a bunch of patches that get the code
ready for OF support.
o Lantiq and BCM47XX platform have a few improvements and bug fixes.
o MIPS has sent a few patches that get the kernel ready for the
upcoming microMIPS support.
o The rest of the series is made up of small bug fixes and cleanups
that relate to various parts of the MIPS code. The biggy in there is
a whitespace cleanup. After I was sent another set of whitespace
cleanup patches I decided it was the time to clean the whitespace
"issues" for once and and that touches many files below arch/mips/.
Fix up silly conflicts, mostly due to whitespace cleanups.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (105 commits)
MIPS: Quit exporting kernel internel break codes to uapi/asm/break.h
MIPS: remove broken conditional inside vpe loader code
MIPS: SMTC: fix implicit declaration of set_vi_handler
MIPS: early_printk: drop __init annotations
MIPS: Probe for and report hardware virtualization support.
MIPS: ath79: add support for the Qualcomm Atheros AP136-010 board
MIPS: ath79: add USB controller registration code for the QCA955X SoCs
MIPS: ath79: add PCI controller registration code for the QCA955X SoCs
MIPS: ath79: add WMAC registration code for the QCA955X SoCs
MIPS: ath79: register UART for the QCA955X SoCs
MIPS: ath79: add QCA955X specific glue to ath79_device_reset_{set, clear}
MIPS: ath79: add GPIO setup code for the QCA955X SoCs
MIPS: ath79: add IRQ handling code for the QCA955X SoCs
MIPS: ath79: add clock setup code for the QCA955X SoCs
MIPS: ath79: add SoC detection code for the QCA955X SoCs
MIPS: ath79: add early printk support for the QCA955X SoCs
MIPS: ath79: fix WMAC IRQ resource assignment
mips: reserve elfcorehdr
mips: Make sure kernel memory is in iomem
MIPS: ath79: use dynamically allocated USB platform devices
...
Commit 0cc41e4a21 (arch: remove direct definitions of KERN_<LEVEL>
uses) is broken - not enough thought was put into changing:
.asciz "string"
to
.asciz "string1" "string2"
The problem is that each string gets _separately_ NUL terminated, so
the result is a string containing:
"string1\0string2\0"
rather than:
"string1string2\0"
With our new printk levels, this ends up as - eg, KERN_DEBUG "string":
0x01 0x00 0x07 0x00 "string" 0x00
which produces lots of \x01 in the kernel log.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no hypercall to setup multiple MSI per PCI device.
As such with these two new commits:
- 08261d87f7
PCI/MSI: Enable multiple MSIs with pci_enable_msi_block_auto()
- 5ca72c4f7c
AHCI: Support multiple MSIs
we would call the PHYSDEVOP_map_pirq 'nvec' times with the same
contents of the PCI device. Sander discovered that we would get
the same PIRQ value 'nvec' times and return said values to the
caller. That of course meant that the device was configured only
with one MSI and AHCI would fail with:
ahci 0000:00:11.0: version 3.0
xen: registering gsi 19 triggering 0 polarity 1
xen: --> pirq=19 -> irq=19 (gsi=19)
(XEN) [2013-02-27 19:43:07] IOAPIC[0]: Set PCI routing entry (6-19 -> 0x99 -> IRQ 19 Mode:1 Active:1)
ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
ahci: probe of 0000:00:11.0 failed with error -22
That is b/c in ahci_host_activate the second call to
devm_request_threaded_irq would return -EINVAL as we passed in
(on the second run) an IRQ that was never initialized.
CC: stable@vger.kernel.org
Reported-and-Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The ath79_wdt driver uses a fixed memory address
currently. Although this is working with each
currently supported SoCs, but this may change
in the future. Additionally, the driver includes
platform specific header files in order to be
able to get the memory base of the watchdog
device.
The patch adds a memory resource to the platform
device, and converts the driver to get the base
address of the watchdog device from that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove the static watchdog device variable and use
the 'platform_device_register_simple' helper to
allocate and register the device in one step.
This allows us to save a few bytes in the kernel image.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
* More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers here,
ethernet and PCI still remain.
* SMP support for mvebu is improved with support for the
local interrupt controller.
* The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the patches
in his tree that all of the patches in this branch are based on, which
caused merge conflicts between the new and old versions of those patches.
To work around the merge conflicts, this branch rebases all patches
on top of the respective MMC patches that did get merged into 3.9.
The patches are all identical to the versions that were part of
linux-next, but have a new commit date.
Merge conflicts:
* in board-nsa310.c, the gpio.h inclusion was removed prematurely and
put back as a bug fix earlier. With this series it is really not needed
any more.
* The patch to add rtc support was already applied by Andrew Morton,
and conflicts with a second copy that was in this series, which adds
a lot of other devices to arch/arm/boot/dts/armada-370-xp.dtsi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7l0+
-----END PGP SIGNATURE-----
Merge tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC mvebu platform changes from Olof Johansson:
"This series contains changes for the Marvell EBU platforms (mvebu,
orion, kirkwood, dove) that were not part of the first set of pull
requests because of dependencies on the MMC tree, and being submitted
a little late.
Notable changes are:
- More devices get moved out of board files into device tree
descriptions. The remaining devices listed in there have patches
that will get sent for 3.10, after which we can remove a lot of the
board files entirely. We are doing the pinctrl and mmc drivers
here, ethernet and PCI still remain.
- SMP support for mvebu is improved with support for the local
interrupt controller.
- The Guruplug board file gets replaced with a DT description.
Unfortunately, the dependency on the MMC tree turned out to be a much
larger problem than expected, when the MMC maintainer rebased the
patches in his tree that all of the patches in this branch are based
on, which caused merge conflicts between the new and old versions of
those patches.
To work around the merge conflicts, this branch rebases all patches on
top of the respective MMC patches that did get merged into 3.9. The
patches are all identical to the versions that were part of
linux-next, but have a new commit date."
* tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (90 commits)
arm: mvebu: enable the SD card slot on Armada 370 Reference Design board
ARM: kirkwood: topkick: init mvsdio via DT
ARM: kirkwood: nsa310: convert to pinctrl
ARM: Kirkwood: topkick: Enable i2c bus.
ARM: kirkwood: topkick: convert to pinctrl
ARM: dove: convert serial DT nodes to clocks property
arm: mvebu: Add SPI flash on Armada 370 DB board
arm: mvebu: Add SPI flash on Armada XP-DB board
arm: mvebu: Add SPI flash on Armada XP-GP board
arm: mvebu: Add support for SPI controller in Armada 370/XP
clocksource: update and move armada-370-xp-timer documentation to timer directory
arm: mvebu: update DT to support local timers
ARM: Dove: convert usb host controller to DT
arm: mvebu: Enable USB controllers on Armada 370/XP boards
arm: mvebu: Add support for USB host controllers in Armada 370/XP
arm: mvebu: add button for OpenBlocks AX3-4
ARM: Kirkwood: Convert NS2 to gpio-poweroff.
ARM: Kirkwood: Convert NSA310 I2C to device tree
ARM: Kirkwood: Convert NSA310 to use gpio-poweroff driver
ARM: Kirkwood: Convert NSA310 to DT based regulators.
...
This branch contains changes for OMAP that came in late during the release
staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs (Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and revision
detection, as well as removal of some dead code (CONFIG_32K_TIMER_HZ)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/vBT
-----END PGP SIGNATURE-----
Merge tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late OMAP changes from Olof Johansson:
"This branch contains changes for OMAP that came in late during the
release staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs
(Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and
revision detection, as well as removal of some dead code
(CONFIG_32K_TIMER_HZ)"
* tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: omap2: include linux/errno.h in hwmod_reset
ARM: OMAP2+: fix some omap_device_build() calls that aren't compiled by default
ARM: OMAP4: hwmod data: Enable AESS hwmod device
ARM: OMAP4: hwmod data: Update AESS data with memory bank area
ARM: OMAP4+: AESS: enable internal auto-gating during initial setup
ASoC: TI AESS: add autogating-enable function, callable from architecture code
ARM: OMAP2+: hwmod: add enable_preprogram hook
ARM: OMAP4: clock data: Add missing clkdm association for dpll_usb
ARM: OMAP2+: PM: Fix the dt return condition in pm_late_init()
ARM: OMAP2: am33xx-hwmod: Fix "register offset NULL check" bug
ARM: OMAP2+: AM33xx: hwmod: add missing HWMOD_NO_IDLEST flags
ARM: OMAP: AM33xx hwmod: Add parent-child relationship for PWM subsystem
ARM: OMAP: AM33xx hwmod: Corrects PWM subsystem HWMOD entries
ARM: DTS: AM33XX: Add nodes for OCMC RAM and WKUP-M3
ARM: OMAP2+: AM33XX: Update the hardreset API
ARM: OMAP2+: AM33XX: hwmod: Update the WKUP-M3 hwmod with reset status bit
ARM: OMAP2+: AM33XX: hwmod: Fixup cpgmac0 hwmod entry
ARM: OMAP2+: AM33XX: hwmod: Update TPTC0 hwmod with the right flags
ARM: OMAP2+: AM33XX: hwmod: Register OCMC RAM hwmod
ARM: OMAP2+: AM33XX: CM/PRM: Use __ASSEMBLER__ macros in header files
...
This branch contains of devicetree changes for the Freescale i.MX platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process since
every line of the file is touched.
On top of that are a handful of the regular changes; enabling more boards
as DT-based instead of legacy board files (mx25pdk), enabling another
driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other platforms
in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=72aL
-----END PGP SIGNATURE-----
Merge tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
Pull thermal management updates from Zhang Rui:
"Highlights:
- introduction of Dove thermal sensor driver.
- introduction of Kirkwood thermal sensor driver.
- introduction of intel_powerclamp thermal cooling device driver.
- add interrupt and DT support for rcar thermal driver.
- add thermal emulation support which allows platform thermal driver
to do software/hardware emulation for thermal issues."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
thermal: rcar: remove __devinitconst
thermal: return an error on failure to register thermal class
Thermal: rename thermal governor Kconfig option to avoid generic naming
thermal: exynos: Use the new thermal trend type for quick cooling action.
Thermal: exynos: Add support for temperature falling interrupt.
Thermal: Dove: Add Themal sensor support for Dove.
thermal: Add support for the thermal sensor on Kirkwood SoCs
thermal: rcar: add Device Tree support
thermal: rcar: remove machine_power_off() from rcar_thermal_notify()
thermal: rcar: add interrupt support
thermal: rcar: add read/write functions for common/priv data
thermal: rcar: multi channel support
thermal: rcar: use mutex lock instead of spin lock
thermal: rcar: enable CPCTL to use hardware TSC deciding
thermal: rcar: use parenthesis on macro
Thermal: fix a build warning when CONFIG_THERMAL_EMULATION cleared
Thermal: fix a wrong comment
thermal: sysfs: Add a new sysfs node emul_temp for thermal emulation
PM: intel_powerclamp: off by one in start_power_clamp()
thermal: exynos: Miscellaneous fixes to support falling threshold interrupt
...
The Armada 370 Reference Design board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this IP. there are no
GPIOs for card-detect and write-protect so we do not specify any.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
of_serial now has support for using clocks property and we have
a DT clock provider. This patch replaces the hard coded clock-frequency
property with a clocks phandle to tclk.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch add support for the SPI flash MX25l25635E which is present
on the Armada 370 DB board. This flash stores the bootloader and its
environment.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch add support for the SPI flash M25P64 which is present on
the Armada XP DB board. This flash stores the bootloader and its
environment.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds an SPI master device node for Armada XP-GP board.
This master node is an SPI flash controller 'n25q128a13'.
Since there is no 'partitions' node declared, one full sized
partition named as the device will be created.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Tested-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP SoC has an SPI controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.
Note that the Armada XP SPI register length is 0x50 bytes,
while Armada 370 SPI register length is 0x28 bytes,
so we choose the smaller of the two.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the time-armada-370-xp support local timers, updated the
device tree to take it into account.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With DT support for orion-ehci also convert Dove to it and
remove the legacy calls and clock aliases.
This patch is based on "ARM: Dove: split legacy and DT setup"
applied to mvebu/boards recently.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch activates every USB port provided by each SoC.
Except for Armada XP Openblocks AX3-4 board,
where we enable only the first two USB ports
until we have more information on the third one usage.
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP SoC has an Orion EHCI USB controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The OpenBlocks AX3-4 board has one software-controlled button on the
front side, labeled "INIT", so we add minimal support for this button
in the kernel.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Remove C code and add a Device Tree node in its place.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add a sub-node into the I2C node to represent the adt7476 device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Remove the C code and add a Device Tree node for gpio-poweroff.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
CuBox needs to enable USB power on a gpio pin. Add a fixed regulator
to always enable usb power on boot.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
gpio-leds has support for pinctrl allocation, make use of it.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The 88f6282 has one more TWSI(TWSI1). This add the information to enable
pinctl of TWSI1.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds a pinmux option, pmx_sdio, to enable the muxing of
the SDIO interface on the 88F6282 SoC from Marvell.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the mvsdio driver has a Device Tree binding, and the SDIO
controller is declared in kirkwood.dtsi, migrate the mplcec4 board to
use the Device Tree to probe the SDIO controller and to mux the pins
of the SDIO interface correctly.
This patch has not been tested, it remains to be tested by a person
having access to the hardware.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Stefan Peter <s.peter@mpl.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the mvsdio driver has a Device Tree binding, and the SDIO
controller is declared in kirkwood.dtsi, migrate the dreamplug board
to use the Device Tree to probe the SDIO controller and to mux this
interface properly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the SDIO controller has a Device Tree binding, let's use it
in kirkwood.dtsi.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Globalscale Mirabox uses the SDIO interface of the Armada 370 to
connect to a Wifi/Bluetooth SD8787 chip, so we enable the SDIO
interface of this board in its Device Tree file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP DB evaluation board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we add a device tree
description for it.
However, in the default configuration of the board, the SD card slot
is not usable: the connector plugged into CON40 must be changed
against a different one, provided with the board by the
manufacturer. Since such a manual modification of the hardware is
needed, we did not enable the SDIO interface by default, and left it
to the board user to modify the Device Tree if needed. Since this
board is really only an evaluation board for developers and not a
final product, it is not too bad.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP DB evaluation board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this
IP. Unfortunately, there are no GPIOs for card-detect and
write-protect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The SDIO interface is only available on pins MPP30/31/32/33/34/35 on
the various Armada XP variants, so we provide a pin muxing option for
this in the Armada XP .dtsi files.
Even though those muxing options are the same for MV78230, MV78260 and
MV78460, we keep them in each .dtsi file, because the number of pins,
and therefore the declaration of the pinctrl node, is different for
each SoC variant.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The SDIO interface is available either on pins MPP9/11/12/13/14/15 or
MPP47/48/49/50/51/52 on the Armada 370. Even though all combinations
are potentially possible, those two muxing options are the most
probable ones, so we provide those at the SoC level .dtsi file.
In practice, in turns out the Armada 370 DB board uses the former,
while the Armada 370 Mirabox uses the latter.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the mvsdio MMC driver has a Device Tree binding, we add the
Device Tree informations to describe the SDIO interface available in
the Armada 370/XP SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP Socs have the same controller that the
one used in the orion platforms. This patch updates the device tree
for these SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some of the mvebu boards (mainly the development board) come with
plug-in RAM modules. This patch allows to let the bootloaders which
have no support for DTS to give the real amount of memory available on
the board.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP DB-MV784MP-GP board has an SPI flash device.
These options allow to access that device over MTD.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is the new Armada XP evaluation board from Marvell. It comes with
a RS232 port over USB, a SATA link, an internal SSD, 4 Ethernet
Gigabit links.
Support for USB (Host and device), SDIO, PCIe will be added as drivers
when they become available for Armada XP in mainline.
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that we have support for local timers, enable it by default
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
MPIC allows the use of private interrupt for each CPUs. The 28th first
interrupts are per-cpu. This patch adds support to use them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add a device tree entry for the Guruplug Server Plus board. This port
was based both on the work done on the dreamplug and the dockstar.
It builds, boots and works on my Guruplug Server Plus.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds the DTS file to support the Marvell RD-A370-A1
(Reference Design board) also known as RD-88F6710 board. It is almost
entirely similar to the DB-A370 board except that the first Ethernet PHY
is SGMII-wired and the second is a switch which is RGMII-wired.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch makes the interrupt controller driver more SMP aware for
the Armada XP SoCs. It adds the support for the per-CPU irq. It also
adds the implementation for the set_affinity hook.
Patch initialy wrote by Yehuda Yitschak and reworked by Gregory
CLEMENT.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In the beginning of DT for Dove it was reasonable to have it close to
non-DT code. With improved DT support, it became more and more difficult
to not break non-DT while changing DT code.
This patch splits up DT board setup and introduces a DOVE_LEGACY config
to allow to remove legacy code for DT-only kernels.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This refreshes the dove_defconfig, and adds:
PRINTK_TIME
DEVTMPFS
EXT4
They're quite useful, and allows booting a cubox ubuntu rootfs on SD card,
since that by default uses ext4.
The rest of the churn is due to options and defaults moving around, no
functional difference.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that SDIO is instantiated via DT, and the SDIO DT node has a clocks
property, we no longer need a C coded clock alias. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that USB is instantiated via DT, and the USB DT node has a clocks
property, we no longer need a C coded clock alias. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The OpenBlocks AX3-4 platform has several LEDs, so it sounds wise to
enable LED support in mvebu_defconfig. We anticipate that more
platforms using Marvell EBU SoCs will have LEDs in the future.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Globalscale Mirabox platform, based on the Armada 370 from
Marvell, has a SD8787 Wireless/Bluetooth chip connected on the SDIO
interface. Now that the mvsdio has a Device Tree binding, and the
necessary Device Tree informations have been added at the SoC and
board level, let's enable the btmrvl driver for the Bluetooth part of
the SD8787 chip.
For now, the driver gets probed correctly, detects the device but
apparently fails to push the firmware to the device:
Bluetooth: vendor=0x2df, device=0x911a, class=255, fn=2
Bluetooth: FW failed to be active in time!
Bluetooth: Downloading firmware failed!
Bluetooth: vendor=0x2df, device=0x911b, class=255, fn=3
Bluetooth: FW failed to be active in time!
Bluetooth: Downloading firmware failed!
This will have to be investigated separately.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Globalscale Mirabox platform, based on the Armada 370 from
Marvell, has a SD8787 Wireless chip connected on the SDIO
interface. Now that the mvsdio has a Device Tree binding, and the
necessary Device Tree informations have been added at the SoC and
board level, let's enable the mwifiex driver for the Wireless part of
the SD8787 chip.
For now, the driver gets probed correctly, detects a device and shows
the network interfaces. However, scanning Wifi networks doesn't work
for now, with a 'CMD_RESP: cmd 0x6 error, result=0x1' message. This
will have to be investigated separately.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the mvsdio driver has gained Device Tree support and the
necessary Device Tree informations has been added for Armada 370 and
Armada XP platforms, we enable the MMC subsystem and the mvsdio driver
in mvebu_defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The RTC class driver is already part of the mvebu_defconfig but the
Marvell internal RTC not yet. Now that its support is added for mvebu
let's update the config file.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The git commit 8eaffa67b4
(xen/pat: Disable PAT support for now) explains in details why
we want to disable PAT for right now. However that
change was not enough and we should have also disabled
the pat_enabled value. Otherwise we end up with:
mmap-example:3481 map pfn expected mapping type write-back for
[mem 0x00010000-0x00010fff], got uncached-minus
------------[ cut here ]------------
WARNING: at /build/buildd/linux-3.8.0/arch/x86/mm/pat.c:774 untrack_pfn+0xb8/0xd0()
mem 0x00010000-0x00010fff], got uncached-minus
------------[ cut here ]------------
WARNING: at /build/buildd/linux-3.8.0/arch/x86/mm/pat.c:774
untrack_pfn+0xb8/0xd0()
...
Pid: 3481, comm: mmap-example Tainted: GF 3.8.0-6-generic #13-Ubuntu
Call Trace:
[<ffffffff8105879f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff810587fa>] warn_slowpath_null+0x1a/0x20
[<ffffffff8104bcc8>] untrack_pfn+0xb8/0xd0
[<ffffffff81156c1c>] unmap_single_vma+0xac/0x100
[<ffffffff81157459>] unmap_vmas+0x49/0x90
[<ffffffff8115f808>] exit_mmap+0x98/0x170
[<ffffffff810559a4>] mmput+0x64/0x100
[<ffffffff810560f5>] dup_mm+0x445/0x660
[<ffffffff81056d9f>] copy_process.part.22+0xa5f/0x1510
[<ffffffff81057931>] do_fork+0x91/0x350
[<ffffffff81057c76>] sys_clone+0x16/0x20
[<ffffffff816ccbf9>] stub_clone+0x69/0x90
[<ffffffff816cc89d>] ? system_call_fastpath+0x1a/0x1f
---[ end trace 4918cdd0a4c9fea4 ]---
(a similar message shows up if you end up launching 'mcelog')
The call chain is (as analyzed by Liu, Jinsong):
do_fork
--> copy_process
--> dup_mm
--> dup_mmap
--> copy_page_range
--> track_pfn_copy
--> reserve_pfn_range
--> line 624: flags != want_flags
It comes from different memory types of page table (_PAGE_CACHE_WB) and MTRR
(_PAGE_CACHE_UC_MINUS).
Stefan Bader dug in this deep and found out that:
"That makes it clearer as this will do
reserve_memtype(...)
--> pat_x_mtrr_type
--> mtrr_type_lookup
--> __mtrr_type_lookup
And that can return -1/0xff in case of MTRR not being enabled/initialized. Which
is not the case (given there are no messages for it in dmesg). This is not equal
to MTRR_TYPE_WRBACK and thus becomes _PAGE_CACHE_UC_MINUS.
It looks like the problem starts early in reserve_memtype:
if (!pat_enabled) {
/* This is identical to page table setting without PAT */
if (new_type) {
if (req_type == _PAGE_CACHE_WC)
*new_type = _PAGE_CACHE_UC_MINUS;
else
*new_type = req_type & _PAGE_CACHE_MASK;
}
return 0;
}
This would be what we want, that is clearing the PWT and PCD flags from the
supported flags - if pat_enabled is disabled."
This patch does that - disabling PAT.
CC: stable@vger.kernel.org # 3.3 and further
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reported-and-Tested-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Get rid of this one (false positive):
arch/s390/kernel/module.c: In function ‘apply_relocate_add’:
arch/s390/kernel/module.c:404:5: warning: ‘rc’ may be used uninitialized
in this function [-Wmaybe-uninitialized]
arch/s390/kernel/module.c:225:6: note: ‘rc’ was declared here
Play safe and preinitialize rc with an error value, so we see an error
if new users indeed don't initialize it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the kernel resides in home space and the mvcos instruction is not
available uaccesses for kernel ds happen via simple strnlen() or memcpy()
calls.
This however can break badly, since uaccesses in kernel space may fail as
well, especially if CONFIG_DEBUG_PAGEALLOC is turned on.
To fix this implement strnlen_kernel() and copy_in_kernel() functions
which can only be used by the page table uaccess functions. These two
functions detect invalid memory accesses and return the correct length
of processed data.. Both functions are more or less a copy of the std
variants without sacf calls.
Fixes ipl crashes on 31 bit machines as well on 64 bit machines without
mvcos. Caused by changing the default address space of the kernel being
home space.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The "standard" and page table walk variants of strncpy_from_user() first
check the length of the to be copied string in userspace.
The string is then copied to kernel space and the length returned to the
caller.
However userspace can modify the string at any time while the kernel
checks for the length of the string or copies the string. In result the
returned length of the string is not necessarily correct.
Fix this by copying in a loop which mimics the mvcos variant of
strncpy_from_user(), which handles this correctly.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We are using sizeof operator for an array given as function argument,
which is incorrect.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
access_ok() always returns 'true' on s390. Therefore all calls
are quite pointless and can be removed.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the maximum length specified for the to be accessed string for
strncpy_from_user() and strnlen_user() is zero the following incorrect
values would be returned or incorrect memory accesses would happen:
strnlen_user_std() and strnlen_user_pt() incorrectly return "1"
strncpy_from_user_pt() would incorrectly access "dst[maxlen - 1]"
strncpy_from_user_mvcos() would incorrectly return "-EFAULT"
Fix all these oddities by adding early checks.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Always stay within page boundaries when copying from user within
strlen_user_mvcos()/strncpy_from_user_mvcos(). This allows to
shorten the code a bit and may prevent unnecessary faults, since
we copy quite large amounts of memory to kernel space.
Also directly call the mvcos variants of copy_from_user() to
avoid indirect branches.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add hint to the page tables that we don't care about the change bit
in storage keys that belong to vmemmap pages.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The physical memory fixmapped for the pvclock clock_gettime vsyscall
was allocated, and thus is not a kernel symbol. __pa() is the proper
method to use in this case.
Fixes the crash below when booting a next-20130204+ smp guest on a
3.8-rc5+ KVM host.
[ 0.666410] udevd[97]: starting version 175
[ 0.674043] udevd[97]: udevd:[97]: segfault at ffffffffff5fd020
ip 00007fff069e277f sp 00007fff068c9ef8 error d
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Merge third patch-bumb from Andrew Morton:
"This wraps me up for -rc1.
- Lots of misc stuff and things which were deferred/missed from
patchbombings 1 & 2.
- ocfs2 things
- lib/scatterlist
- hfsplus
- fatfs
- documentation
- signals
- procfs
- lockdep
- coredump
- seqfile core
- kexec
- Tejun's large IDR tree reworkings
- ipmi
- partitions
- nbd
- random() things
- kfifo
- tools/testing/selftests updates
- Sasha's large and pointless hlist cleanup"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (163 commits)
hlist: drop the node parameter from iterators
kcmp: make it depend on CHECKPOINT_RESTORE
selftests: add a simple doc
tools/testing/selftests/Makefile: rearrange targets
selftests/efivarfs: add create-read test
selftests/efivarfs: add empty file creation test
selftests: add tests for efivarfs
kfifo: fix kfifo_alloc() and kfifo_init()
kfifo: move kfifo.c from kernel/ to lib/
arch Kconfig: centralise CONFIG_ARCH_NO_VIRT_TO_BUS
w1: add support for DS2413 Dual Channel Addressable Switch
memstick: move the dereference below the NULL test
drivers/pps/clients/pps-gpio.c: use devm_kzalloc
Documentation/DMA-API-HOWTO.txt: fix typo
include/linux/eventfd.h: fix incorrect filename is a comment
mtd: mtd_stresstest: use prandom_bytes()
mtd: mtd_subpagetest: convert to use prandom library
mtd: mtd_speedtest: use prandom_bytes
mtd: mtd_pagetest: convert to use prandom library
mtd: mtd_oobtest: convert to use prandom library
...
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change it to CONFIG_HAVE_VIRT_TO_BUS and set it in all architecures
that already provide virt_to_bus().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the frv arch_get_unmapped_area function to make use of
vm_unmapped_area() instead of implementing a brute force search.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the parisc arch_get_unmapped_area function to make use of
vm_unmapped_area() instead of implementing a brute force search.
[akpm@linux-foundation.org: remove now-unused DCACHE_ALIGN(), per James]
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Acked-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86/EFI changes from Peter Anvin:
- Improve the initrd handling in the EFI boot stub by allowing forward
slashes in the pathname - from Chun-Yi Lee.
- Cleanup code duplication in the EFI mixed kernel/firmware code - from
Satoru Takeuchi.
- efivarfs bug fixes for more strict filename validation, with lots of
input from Al Viro.
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove duplicate code in setup_arch() by using, efi_is_native()
efivarfs: guid part of filenames are case-insensitive
efivarfs: Validate filenames much more aggressively
efivarfs: Use sizeof() instead of magic number
x86, efi: Allow slash in file path of initrd
Pull more x86 fixes from Peter Anvin:
"Additional x86 fixes. Three of these patches are pure documentation,
two are pretty trivial; the remaining one fixes boot problems on some
non-BIOS machines."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Make sure we can boot in the case the BDA contains pure garbage
x86, efi: Mark disable_runtime as __initdata
x86, doc: Fix incorrect comment about 64-bit code segment descriptors
doc, kernel-parameters: Document 'console=hvc<n>'
doc, xen: Mention 'earlyprintk=xen' in the documentation.
ACPI: Overriding ACPI tables via initrd only works with an initrd and on X86
On non-BIOS platforms it is possible that the BIOS data area contains
garbage instead of being zeroed or something equivalent (firmware
people: we are talking of 1.5K here, so please do the sane thing.)
We need on the order of 20-30K of low memory in order to boot, which
may grow up to < 64K in the future. We probably want to avoid the
lowest of the low memory. At the same time, it seems extremely
unlikely that a legitimate EBDA would ever reach down to the 128K
(which would require it to be over half a megabyte in size.) Thus,
pick 128K as the cutoff for "this is insane, ignore." We may still
end up reserving a bunch of extra memory on the low megabyte, but that
is not really a major issue these days. In the worst case we lose
512K of RAM.
This code really should be merged with trim_bios_range() in
arch/x86/kernel/setup.c, but that is a bigger patch for a later merge
window.
Reported-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/n/tip-oebml055yyfm8yxmria09rja@git.kernel.org
The upstream kernel ABI (v3) is different from current out-of-tree (v2):
* no-legacy-syscalls
* user_regs_struct layout has changed
So we rev up the ABI version
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ptrace regset interface relies on ELF_NGREG for ceiling the size of user
request. So any larger request (even if legit) would be clipped.
The existing def of ELF_NGREG didn't use user_regs_struct and was
technically one placeholder short (stop_pc) - although the current code
would still work because pt_regs includes a bunch of extra fields,
making
ELF_NGREG >= sizeof(struct user_regs_struct)/sizeof(long)
But we need to remove this ambiguity, specially since pt_regs should NOT
be directly associated with with anything userspace-ish.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Added features:
- add support for thread local storage (TLS)
- add accept4 and finit_module syscalls
- support medium-priority interrupts
- add support for dc232c processor variant
- support file-base simulated disk for ISS simulator
Bug fixes:
- fix return values returned by the str[n]cmp functions
- avoid mmap cache aliasing
- fix handling of 'windowed registers' in ptrace
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ohgg
-----END PGP SIGNATURE-----
Merge tag 'xtensa-next-20130225' of git://github.com/czankel/xtensa-linux
Pull xtensa update from Chris Zankel:
"Added features:
- add support for thread local storage (TLS)
- add accept4 and finit_module syscalls
- support medium-priority interrupts
- add support for dc232c processor variant
- support file-base simulated disk for ISS simulator
Bug fixes:
- fix return values returned by the str[n]cmp functions
- avoid mmap cache aliasing
- fix handling of 'windowed registers' in ptrace"
* tag 'xtensa-next-20130225' of git://github.com/czankel/xtensa-linux:
xtensa: add accept4 syscall
xtensa: add support for TLS
xtensa: add missing include asm/uaccess.h to checksum.h
xtensa: do not enable GENERIC_GPIO by default
xtensa: complete ptrace handling of register windows
xtensa: add support for oprofile
xtensa: move spill_registers to traps.h
xtensa: ISS: add host file-based simulated disk
xtensa: fix str[n]cmp return value
xtensa: avoid mmap cache aliasing
xtensa: add finit_module syscall
xtensa: pull signal definitions from signal-defs.h
xtensa: fix ipc_parse_version selection
xtensa: dispatch medium-priority interrupts
xtensa: Add config files for Diamond 233L - Rev C processor variant
xtensa: use new common dtc rule
xtensa: rename prom_update_property to of_update_property
Pull microblaze update from Michal Simek:
"Microblaze changes.
After my discussion with Arnd I have also added there asm-generic io
patch which is Acked by him and Geert."
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
asm-generic: io: Fix ioread16/32be and iowrite16/32be
microblaze: Do not use module.h in files which are not modules
microblaze: Fix coding style issues
microblaze: Add missing return from debugfs_tlb
microblaze: Makefile clean
microblaze: Add .gitignore entries for auto-generated files
microblaze: Fix strncpy_from_user macro
Pull OpenRISC updates from Jonas Bonn:
"An equal number of bug fixes and trivial cleanups; no new features.
- Two patches to fix errors thrown by the updated toolchain.
- Three other bug fixes.
- Four trivial cleanups."
* 'for-upstream' of git://openrisc.net/jonas/linux:
openrisc: add missing header inclusion
openrisc: really pass correct arg to schedule_tail
Add bitops include needed for ext2 filesystem
openrisc: update DTLB-miss handler last
openrisc: fix up vmalloc page table loading
openrisc idle: delete pm_idle
openrisc: remove CONFIG_SYMBOL_PREFIX
openrisc: avoid using function parameter regs in reset vector
openrisc: remove unused current_regs
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/pageattr: Prevent PSE and GLOABL leftovers to confuse pmd/pte_present and pmd_huge
Revert "x86, mm: Make spurious_fault check explicitly check explicitly check the PRESENT bit"
x86/mm/numa: Don't check if node is NUMA_NO_NODE
x86, efi: Make "noefi" really disable EFI runtime serivces
x86/apic: Fix parsing of the 'lapic' cmdline option
Besides some fixes and cleanups in the code there are three more
important changes to point out this time:
* New IOMMU driver for the ARM SHMOBILE platform
* An IOMMU-API extension for non-paging IOMMUs (required for
upcoming PAMU driver)
* Rework of the way the Tegra IOMMU driver accesses its
registetrs - register windows are easier to extend now.
There are also a few changes to non-iommu code, but that is acked by the
respective maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=G4Ot
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU Updates from Joerg Roedel:
"Besides some fixes and cleanups in the code there are three more
important changes to point out this time:
* New IOMMU driver for the ARM SHMOBILE platform
* An IOMMU-API extension for non-paging IOMMUs (required for
upcoming PAMU driver)
* Rework of the way the Tegra IOMMU driver accesses its
registetrs - register windows are easier to extend now.
There are also a few changes to non-iommu code, but that is acked by
the respective maintainers."
* tag 'iommu-updates-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (23 commits)
iommu/tegra: assume CONFIG_OF in SMMU driver
iommu/tegra: assume CONFIG_OF in gart driver
iommu/amd: Remove redundant NULL check before dma_ops_domain_free().
iommu/amd: Initialize device table after dma_ops
iommu/vt-d: Zero out allocated memory in dmar_enable_qi
iommu/tegra: smmu: Fix incorrect mask for regbase
iommu/exynos: Make exynos_sysmmu_disable static
ARM: mach-shmobile: r8a7740: Add IPMMU device
ARM: mach-shmobile: sh73a0: Add IPMMU device
ARM: mach-shmobile: sh7372: Add IPMMU device
iommu/shmobile: Add iommu driver for Renesas IPMMU modules
iommu: Add DOMAIN_ATTR_WINDOWS domain attribute
iommu: Add domain window handling functions
iommu: Implement DOMAIN_ATTR_PAGING attribute
iommu: Check for valid pgsize_bitmap in iommu_map/unmap
iommu: Make sure DOMAIN_ATTR_MAX is really the maximum
iommu/tegra: smmu: Change SMMU's dependency on ARCH_TEGRA
iommu/tegra: smmu: Use helper function to check for valid register offset
iommu/tegra: smmu: Support variable MMIO ranges/blocks
iommu/tegra: Add missing spinlock initialization
...
Pull DMA-mapping updates from Marek Szyprowski:
"This time all patches are related only to ARM DMA-mapping subsystem.
The main extension provided by this pull request is highmem support.
Besides that it contains a bunch of small bugfixes and cleanups."
* 'for-v3.9' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: DMA-mapping: fix memory leak in IOMMU dma-mapping implementation
ARM: dma-mapping: Add maximum alignment order for dma iommu buffers
ARM: dma-mapping: use himem for DMA buffers for IOMMU-mapped devices
ARM: dma-mapping: add support for CMA regions placed in highmem zone
arm: dma mapping: export arm iommu functions
ARM: dma-mapping: Add arm_iommu_detach_device()
ARM: dma-mapping: Add macro to_dma_iommu_mapping()
ARM: dma-mapping: Set arm_dma_set_mask() for iommu->set_dma_mask()
ARM: iommu: Include linux/kref.h in asm/dma-iommu.h
This branch contains the usual set of individual driver improvements and
bug fixes, as well as updates to the core code. The more notable changes
include:
- Internally add new API for referencing GPIOs by gpio_desc instead of
number. Eventually this will become a public API
- ACPI GPIO binding support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JN4M
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull GPIO changes from Grant Likely:
"This branch contains the usual set of individual driver improvements
and bug fixes, as well as updates to the core code. The more notable
changes include:
- Internally add new API for referencing GPIOs by gpio_desc instead
of number. Eventually this will become a public API
- ACPI GPIO binding support"
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (33 commits)
arm64: select ARCH_WANT_OPTIONAL_GPIOLIB
gpio: em: Use irq_domain_add_simple() to fix runtime error
gpio: using common order: let 'static const' instead of 'const static'
gpio/vt8500: memory cleanup missing
gpiolib: Fix locking on gpio debugfs files
gpiolib: let gpio_chip reference its descriptors
gpiolib: use descriptors internally
gpiolib: use gpio_chips list in gpiochip_find_base
gpiolib: use gpio_chips list in sysfs ops
gpiolib: use gpio_chips list in gpiochip_find
gpiolib: use gpio_chips list in gpiolib_sysfs_init
gpiolib: link all gpio_chips using a list
gpio/langwell: cleanup driver
gpio/langwell: Add Cloverview ids to pci device table
gpio/lynxpoint: add chipset gpio driver.
gpiolib: add missing braces in gpio_direction_show
gpiolib-acpi: Fix error checks in interrupt requesting
gpio: mpc8xxx: don't set IRQ_TYPE_NONE when creating irq mapping
gpiolib: remove gpiochip_reserve()
arm: pxa: tosa: do not use gpiochip_reserve()
...
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=dYdW
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
Pull LED subsystem update from Bryan Wu.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (61 commits)
leds: leds-sunfire: use dev_err()/pr_err() instead of printk()
leds: 88pm860x: Add missing of_node_put()
leds: tca6507: Use of_get_child_count()
leds: leds-pwm: make it depend on PWM and not HAVE_PWM
Documentation: leds: update LP55xx family devices
leds-lp55xx: fix problem on removing LED attributes
leds-lp5521/5523: add author and copyright description
leds-lp5521/5523: use new lp55xx common header
leds-lp55xx: clean up headers
leds-lp55xx: clean up definitions
leds-lp55xx: clean up unused data and functions
leds-lp55xx: clean up _remove()
leds-lp55xx: add new function for removing device attribtues
leds-lp55xx: code refactoring on selftest function
leds-lp55xx: use common device attribute driver function
leds-lp55xx: support device specific attributes
leds-lp5523: use generic firmware interface
leds-lp5521: use generic firmware interface
leds-lp55xx: support firmware interface
leds-lp55xx: add new lp55xx_register_sysfs() for the firmware interface
...
Pull slave-dmaengine updates from Vinod Koul:
"This is fairly big pull by my standards as I had missed last merge
window. So we have the support for device tree for slave-dmaengine,
large updates to dw_dmac driver from Andy for reusing on different
architectures. Along with this we have fixes on bunch of the drivers"
Fix up trivial conflicts, usually due to #include line movement next to
each other.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (111 commits)
Revert "ARM: SPEAr13xx: Pass DW DMAC platform data from DT"
ARM: dts: pl330: Add #dma-cells for generic dma binding support
DMA: PL330: Register the DMA controller with the generic DMA helpers
DMA: PL330: Add xlate function
DMA: PL330: Add new pl330 filter for DT case.
dma: tegra20-apb-dma: remove unnecessary assignment
edma: do not waste memory for dma_mask
dma: coh901318: set residue only if dma is in progress
dma: coh901318: avoid unbalanced locking
dmaengine.h: remove redundant else keyword
dma: of-dma: protect list write operation by spin_lock
dmaengine: ste_dma40: do not remove descriptors for cyclic transfers
dma: of-dma.c: fix memory leakage
dw_dmac: apply default dma_mask if needed
dmaengine: ioat - fix spare sparse complain
dmaengine: move drivers/of/dma.c -> drivers/dma/of-dma.c
ioatdma: fix race between updating ioat->head and IOAT_COMPLETION_PENDING
dw_dmac: add support for Lynxpoint DMA controllers
dw_dmac: return proper residue value
dw_dmac: fill individual length of descriptor
...
The flat DT (currently embedded in vmlinux) is in .init section.
The unflattened/binary tree doesn't copy strings through and references
them from orig flat DT - which could cause catestrohpy if of_* APIs are
called post init, say from a driver which is a loadable module.
Reported-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Prevents build issue with updated toolchain
Reported-by: Jack Thomasson <jkt@moonlitsw.com>
Tested-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
- Fixes for blackfin and microblaze build problems introduced by the
removal of global pm_idle. From Lars-Peter Clausen.
- OPP core build fix from Shawn Guo.
- Error condition check fix for the new imx6q-cpufreq driver from
Wei Yongjun.
- Fix for an AER driver crash related to the lack of APEI
initialization for acpi=off. From Rafael J. Wysocki.
- Fix for a USB breakage on Thinkpad T430 related to ACPI power
resources and PCI wakeup from Rafael J. Wysocki.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJRKUy/AAoJEKhOf7ml8uNsKskQAIj8rzVUsQcyk77U2NmACLhE
EGdcxiwLrOc5bR2NEwyF66VN398pYrC2BqtCsj7vE070YEdt8VOcfOQ7FNtp3Z8R
hgGkpALL6QusV3V+f9rOxberqbU+Ei7XzeZs/74gilTF5+xFDt8Vd+PkJSMzpOug
BX06ZP5NWALL2qUKbJsz6TTLY1IjkxNrcn4iWMNcCZfCFS4r9KFd9SJhiD9lDY66
FdE2H69IDWrIEoPuEQHVk79YZu9CKUldMdBAIYfyWGSpxZ5IU/fmvIKlamFgTT7I
Voz0l69TTSlQYp+6WG7HCla6B371BwYEvZOgjgXNzW+gVPaqj9+wTpOln1GX4oZc
qBukY59b1NgaJahwX/lHaJZckoF0gcBoqCp3eW3LMPe6tkVk/Kd4cRrTCUXgUMtX
IHMZc/jkqMQmvEspXqzc+/mZAf9RBzUMG7mgDG4yrxPoSLBUZM1DOWG93lqc6T9u
nPhvb444GaDRilAc8vW/Bnc5hzaMYGlpoX2MCi0aisevcvD6c5aW4HZ80UirZMPA
OiOvQJ4vbtdFTrlupv0kBE+fKFXyb+qYtVkrAemcAyvo4KmEbS5n1p79NnI8S4Sp
DNk/Fh+nUG0t9EKS0bnH/MZYVWqPaTPIq7StUf/iicngLfSIGj4zPflL0GjjC6Wf
gWqNH0wjit/64gUQsQAN
=FCbx
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-fixes-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Fixes for blackfin and microblaze build problems introduced by the
removal of global pm_idle. From Lars-Peter Clausen.
- OPP core build fix from Shawn Guo.
- Error condition check fix for the new imx6q-cpufreq driver from Wei
Yongjun.
- Fix for an AER driver crash related to the lack of APEI
initialization for acpi=off. From Rafael J Wysocki.
- Fix for a USB breakage on Thinkpad T430 related to ACPI power
resources and PCI wakeup from Rafael J. Wysocki.
* tag 'pm+acpi-fixes-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Take unusual configurations of power resources into account
imx6q-cpufreq: fix return value check in imx6q_cpufreq_probe()
PM / OPP: fix condition for empty of_init_opp_table()
ACPI / APEI: Fix crash in apei_hest_parse() for acpi=off
microblaze idle: Fix compile error
blackfin idle: Fix compile error
Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ER3b
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)"
* tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
PCI/ACPI: Don't cache _PRT, and don't associate them with bus numbers
PCI: Fix PCI Express Capability accessors for PCI_EXP_FLAGS
ACPI / PCI: Make pci_slot built-in only, not a module
PCI/PM: Clear state_saved during suspend
PCI: Use atomic_inc_return() rather than atomic_add_return()
PCI: Catch attempts to disable already-disabled devices
PCI: Disable Bus Master unconditionally in pci_device_shutdown()
PCI: acpiphp: Remove dead code for PCI host bridge hotplug
PCI: acpiphp: Create companion ACPI devices before creating PCI devices
PCI: Remove unused "rc" in virtfn_add_bus()
PCI: pciehp: Drop suspend/resume ENTRY messages
PCI/ASPM: Don't touch ASPM if forcibly disabled
PCI/ASPM: Deallocate upstream link state even if device is not PCIe
PCI: Document MPS parameters pci=pcie_bus_safe, pci=pcie_bus_perf, etc
PCI: Document hpiosize= and hpmemsize= resource reservation parameters
PCI: Use PCI Express Capability accessor
PCI: Introduce accessor to retrieve PCIe Capabilities Register
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
...
disable_runtime is only referenced from __init functions, so mark it
as __initdata.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1361545427-26393-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull KVM ARM compile fixes from Gleb Natapov:
"Fix ARM KVM compilation breakage due to changes from kvm.git"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
ARM: KVM: fix compilation after removal of user_alloc from struct kvm_memory_slot
ARM: KVM: Rename KVM_MEMORY_SLOTS -> KVM_USER_MEM_SLOTS
ARM: KVM: fix kvm_arch_{prepare,commit}_memory_region
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.9:
- Added accelerated implementation of crc32 using pclmulqdq.
- Added test vector for fcrypt.
- Added support for OMAP4/AM33XX cipher and hash.
- Fixed loose crypto_user input checks.
- Misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (43 commits)
crypto: user - ensure user supplied strings are nul-terminated
crypto: user - fix empty string test in report API
crypto: user - fix info leaks in report API
crypto: caam - Added property fsl,sec-era in SEC4.0 device tree binding.
crypto: use ERR_CAST
crypto: atmel-aes - adjust duplicate test
crypto: crc32-pclmul - Kill warning on x86-32
crypto: x86/twofish - assembler clean-ups: use ENTRY/ENDPROC, localize jump labels
crypto: x86/sha1 - assembler clean-ups: use ENTRY/ENDPROC
crypto: x86/serpent - use ENTRY/ENDPROC for assember functions and localize jump targets
crypto: x86/salsa20 - assembler cleanup, use ENTRY/ENDPROC for assember functions and rename ECRYPT_* to salsa20_*
crypto: x86/ghash - assembler clean-up: use ENDPROC at end of assember functions
crypto: x86/crc32c - assembler clean-up: use ENTRY/ENDPROC
crypto: cast6-avx: use ENTRY()/ENDPROC() for assembler functions
crypto: cast5-avx: use ENTRY()/ENDPROC() for assembler functions and localize jump targets
crypto: camellia-x86_64/aes-ni: use ENTRY()/ENDPROC() for assembler functions and localize jump targets
crypto: blowfish-x86_64: use ENTRY()/ENDPROC() for assembler functions and localize jump targets
crypto: aesni-intel - add ENDPROC statements for assembler functions
crypto: x86/aes - assembler clean-ups: use ENTRY/ENDPROC, localize jump targets
crypto: testmgr - add test vector for fcrypt
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=v9Yo
-----END PGP SIGNATURE-----
Merge tag 'please-pull-vm_unwrapped' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 update from Tony Luck:
"ia64 vm patch series that was cooking in -mm tree"
* tag 'please-pull-vm_unwrapped' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
mm: use vm_unmapped_area() in hugetlbfs on ia64 architecture
mm: use vm_unmapped_area() on ia64 architecture
lockdep, but it's a mechanical change.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tiSY
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"The sweeping change is to make add_taint() explicitly indicate whether
to disable lockdep, but it's a mechanical change."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Add option to not sign modules during modules_install
MODSIGN: Add -s <signature> option to sign-file
MODSIGN: Specify the hash algorithm on sign-file command line
MODSIGN: Simplify Makefile with a Kconfig helper
module: clean up load_module a little more.
modpost: Ignore ARC specific non-alloc sections
module: constify within_module_*
taint: add explicit flag to show whether lock dep is still OK.
module: printk message when module signature fail taints kernel.
The AMD64 Architecture Programmer's Manual Volume 2, on page
89 mentions: "If the processor is running in 64-bit mode (L=1),
the only valid setting of the D bit is 0." This matches
with what the code does.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1361825650-14031-4-git-send-email-konrad.wilk@oracle.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Paolo Pisati reports that IPv6 triggers this warning:
BUG: scheduling while atomic: swapper/0/0/0x40000100
Modules linked in:
[<c001b1c4>] (unwind_backtrace+0x0/0xf0) from [<c0503c5c>] (__schedule_bug+0x48/0x5c)
[<c0503c5c>] (__schedule_bug+0x48/0x5c) from [<c0508608>] (__schedule+0x700/0x740)
[<c0508608>] (__schedule+0x700/0x740) from [<c007007c>] (__cond_resched+0x24/0x34)
[<c007007c>] (__cond_resched+0x24/0x34) from [<c05086dc>] (_cond_resched+0x3c/0x44)
[<c05086dc>] (_cond_resched+0x3c/0x44) from [<c0021f6c>] (do_alignment+0x178/0x78c)
[<c0021f6c>] (do_alignment+0x178/0x78c) from [<c00083e0>] (do_DataAbort+0x34/0x98)
[<c00083e0>] (do_DataAbort+0x34/0x98) from [<c0509a60>] (__dabt_svc+0x40/0x60)
Exception stack(0xc0763d70 to 0xc0763db8)
3d60: e97e805e e97e806e 2c000000 11000000
3d80: ea86bb00 0000002c 00000011 e97e807e c076d2a8 e97e805e e97e806e 0000002c
3da0: 3d000000 c0763dbc c04b98fc c02a8490 00000113 ffffffff
[<c0509a60>] (__dabt_svc+0x40/0x60) from [<c02a8490>] (__csum_ipv6_magic+0x8/0xc8)
Fix this by using probe_kernel_address() stead of __get_user().
Cc: <stable@vger.kernel.org>
Reported-by: Paolo Pisati <p.pisati@gmail.com>
Tested-by: Paolo Pisati <p.pisati@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Martin Storsjö reports that the sequence:
ee312ac1 vsub.f32 s4, s3, s2
ee702ac0 vsub.f32 s5, s1, s0
e59f0028 ldr r0, [pc, #40]
ee111a90 vmov r1, s3
on Raspberry Pi (implementor 41 architecture 1 part 20 variant b rev 5)
where s3 is a denormal and s2 is zero results in incorrect behaviour -
the instruction "vsub.f32 s5, s1, s0" is not executed:
VFP: bounce: trigger ee111a90 fpexc d0000780
VFP: emulate: INST=0xee312ac1 SCR=0x00000000
...
As we can see, the instruction triggering the exception is the "vmov"
instruction, and we emulate the "vsub.f32 s4, s3, s2" but fail to
properly take account of the FPEXC_FP2V flag in FPEXC. This is because
the test for the second instruction register being valid is bogus, and
will always skip emulation of the second instruction.
Cc: <stable@vger.kernel.org>
Reported-by: Martin Storsjö <martin@martin.st>
Tested-by: Martin Storsjö <martin@martin.st>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes page_address() usage in IOMMU-aware dma-mapping
implementation and replaced it with direct use of the cpu virtual address
provided by the caller. page_address() returned incorrect address for
pages remapped in atomic pool, what caused memory leak.
Reported-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Hiroshi Doyu <hdoyu@nvidia.com>
Alignment order for a dma iommu buffer is set by buffer size. For
large buffer, it is a waste of iommu address space. So configurable
parameter to limit maximum alignment order can reduce the waste.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin.park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
IOMMU can provide access to any memory page, so there is no point in
limiting the allocated pages only to lowmem, once other parts of
dma-mapping subsystem correctly supports himem pages.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch adds missing pieces to correctly support memory pages served
from CMA regions placed in high memory zones. Please note that the default
global CMA area is still put into lowmem and is limited by optional
architecture specific DMA zone. One can however put device specific CMA
regions in high memory zone to reduce lowmem usage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
This patch adds EXPORT_SYMBOL_GPL calls to the three arm iommu
functions - arm_iommu_create_mapping, arm_iommu_free_mapping
and arm_iommu_attach_device. These three functions are arm specific
wrapper functions for creating/freeing/using an iommu mapping and
they are called by various drivers. If any of these drivers need
to be built as dynamic modules, these functions need to be exported.
Changelog v2: using EXPORT_SYMBOL_GPL as suggested by Marek.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
[m.szyprowski: extended with recently introduced
EXPORT_SYMBOL_GPL(arm_iommu_detach_device)]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This can be built without CONFIG_ARM_DMA_USE_IOMMU.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
struct dma_map_ops iommu_ops doesn't have ->set_dma_mask, which causes
crash when dma_set_mask() is called from some driver.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
The dma_iommu_mapping structure defined in asm/dma-iommu.h embeds a
struct kref, include the appropriate header file.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Commit 7a905b1 (KVM: Remove user_alloc from struct kvm_memory_slot)
broke KVM/ARM by removing the user_alloc field from a public structure.
As we only used this field to alert the user that we didn't support
this operation mode, there is no harm in discarding this bit of code
without any remorse.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Commit bbacc0c (KVM: Rename KVM_MEMORY_SLOTS -> KVM_USER_MEM_SLOTS)
broke KVM/ARM by changing a global #define.
Apply the same change to fix the compilation breakage.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Commit f82a8cfe9 (KVM: struct kvm_memory_slot.user_alloc -> bool)
broke the ARM KVM port by changing the prototype of two global
functions.
Apply the same change to fix the compilation breakage.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data consolidation,
OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee Jones. In
particular, the debugfs and the sysct interfaces got extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the twl-core
driver, with a much needed module id lookup code improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the palmas
GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra and
Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and ab9540 based
devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a better
card detection code path and now also supports the RTS5227 chipset, thanks
to Wei Wang and Roger Tseng.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BhC1
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS updates from Samuel Ortiz:
"This is the MFD pull request for the 3.9 merge window.
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data
consolidation, OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee
Jones. In particular, the debugfs and the sysct interfaces got
extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the
twl-core driver, with a much needed module id lookup code
improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the
palmas GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra
and Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and
ab9540 based devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to
Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a
better card detection code path and now also supports the RTS5227
chipset, thanks to Wei Wang and Roger Tseng."
* tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits)
mfd: lpc_ich: Use devres API to allocate private data
mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH
mfd: lpc_sch: Accomodate partial population of the MFD devices
mfd: da9052-i2c: Staticize da9052_i2c_fix()
mfd: syscon: Fix sparse warning
mfd: twl-core: Fix kernel panic on boot
mfd: rtsx: Fix issue that booting OS with SD card inserted
mfd: ab8500: Fix compile error
mfd: Add missing GENERIC_HARDIRQS dependecies
Documentation: Add docs for max8925 dt
mfd: max8925: Add dts
mfd: max8925: Support dt for backlight
mfd: max8925: Fix onkey driver irq base
mfd: max8925: Fix mfd device register failure
mfd: max8925: Add irqdomain for dt
mfd: vexpress: Allow vexpress-sysreg to self-initialise
mfd: rtsx: Support RTS5227
mfd: rtsx: Implement driving adjustment to device-dependent callbacks
mfd: vexpress: Add pseudo-GPIO based LEDs
mfd: ab8500: Rename ab8500 to abx500 for hwmon driver
...
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
- Xen ACPI memory and CPU hotplug drivers - allowing Xen hypervisor
to be aware of new CPU and new DIMMs
- Cleanups
Bug-fixes:
- Fixes a long-standing bug in the PV spinlock wherein we did not
kick VCPUs that were in a tight loop.
- Fixes in the error paths for the event channel machinery.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRJS1kAAoJEFjIrFwIi8fJj2YIAMO3/LVUZyojX/d8U9pqrCly
lFfEF2UVjcxHJSj0ZFNXt1o3fnYP1SLRlT9u7ZLDjXf6Lmxmw6/C3Haw2wp3DfGq
yUR0G/X9CPTBEgMYDdX7bjeTjyURvZcUaFwr+qodaaeL3uXx2pW6621Sc6jRKuia
yAFVZMAKeaRrvUUIXjKHtlpRp9LKFdSztShMtYqmFvxEwrJPq2b37caKruoUCa6o
X/YO0fvE9QtYD/pG0jsghFmLh/mcr+n9IFMCUXo1Yc9FdQBExtKzABDS5jdpuFND
4aMDE3dqUmHmpbaQhRE7SdblvpyrGdQXL6FSTjvwBgISfLo847CrnRKRgPp0YeA=
=LQeU
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.9-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen update from Konrad Rzeszutek Wilk:
"This has two new ACPI drivers for Xen - a physical CPU offline/online
and a memory hotplug. The way this works is that ACPI kicks the
drivers and they make the appropiate hypercall to the hypervisor to
tell it that there is a new CPU or memory. There also some changes to
the Xen ARM ABIs and couple of fixes. One particularly nasty bug in
the Xen PV spinlock code was fixed by Stefan Bader - and has been
there since the 2.6.32!
Features:
- Xen ACPI memory and CPU hotplug drivers - allowing Xen hypervisor
to be aware of new CPU and new DIMMs
- Cleanups
Bug-fixes:
- Fixes a long-standing bug in the PV spinlock wherein we did not
kick VCPUs that were in a tight loop.
- Fixes in the error paths for the event channel machinery"
Fix up a few semantic conflicts with the ACPI interface changes in
drivers/xen/xen-acpi-{cpu,mem}hotplug.c.
* tag 'stable/for-linus-3.9-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: event channel arrays are xen_ulong_t and not unsigned long
xen: Send spinlock IPI to all waiters
xen: introduce xen_remap, use it instead of ioremap
xen: close evtchn port if binding to irq fails
xen-evtchn: correct comment and error output
xen/tmem: Add missing %s in the printk statement.
xen/acpi: move xen_acpi_get_pxm under CONFIG_XEN_DOM0
xen/acpi: ACPI cpu hotplug
xen/acpi: Move xen_acpi_get_pxm to Xen's acpi.h
xen/stub: driver for CPU hotplug
xen/acpi: ACPI memory hotplug
xen/stub: driver for memory hotplug
xen: implement updated XENMEM_add_to_physmap_range ABI
xen/smp: Move the common CPU init code a bit to prep for PVH patch.
The next change will remove the code from the dw_mmc-exynos that added
the DW_MCI_QUIRK_NO_WRITE_PROTECT. Keep existing functionality of
having no write protect pin on smdk5250 by adding the disable-wp
property.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Without this patch any kernel code that reads kernel memory in
non present kernel pte/pmds (as set by pageattr.c) will crash.
With this kernel code:
static struct page *crash_page;
static unsigned long *crash_address;
[..]
crash_page = alloc_pages(GFP_KERNEL, 9);
crash_address = page_address(crash_page);
if (set_memory_np((unsigned long)crash_address, 1))
printk("set_memory_np failure\n");
[..]
The kernel will crash if inside the "crash tool" one would try
to read the memory at the not present address.
crash> p crash_address
crash_address = $8 = (long unsigned int *) 0xffff88023c000000
crash> rd 0xffff88023c000000
[ *lockup* ]
The lockup happens because _PAGE_GLOBAL and _PAGE_PROTNONE
shares the same bit, and pageattr leaves _PAGE_GLOBAL set on a
kernel pte which is then mistaken as _PAGE_PROTNONE (so
pte_present returns true by mistake and the kernel fault then
gets confused and loops).
With THP the same can happen after we taught pmd_present to
check _PAGE_PROTNONE and _PAGE_PSE in commit
027ef6c878 ("mm: thp: fix pmd_present for
split_huge_page and PROT_NONE with THP"). THP has the same
problem with _PAGE_GLOBAL as the 4k pages, but it also has a
problem with _PAGE_PSE, which must be cleared too.
After the patch is applied copy_user correctly returns -EFAULT
and doesn't lockup anymore.
crash> p crash_address
crash_address = $9 = (long unsigned int *) 0xffff88023c000000
crash> rd 0xffff88023c000000
rd: read error: kernel virtual address: ffff88023c000000 type:
"64-bit KVADDR"
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I got a report for a minor regression introduced by commit
027ef6c878 ("mm: thp: fix pmd_present for split_huge_page and
PROT_NONE with THP").
So the problem is, pageattr creates kernel pagetables (pte and
pmds) that breaks pte_present/pmd_present and the patch above
exposed this invariant breakage for pmd_present.
The same problem already existed for the pte and pte_present and
it was fixed by commit 660a293ea9 ("x86, mm: Make
spurious_fault check explicitly check the PRESENT bit") (if it
wasn't for that commit, it wouldn't even be a regression). That
fix avoids the pagefault to use pte_present. I could follow
through by stopping using pmd_present/pmd_huge too.
However I think it's more robust to fix pageattr and to clear
the PSE/GLOBAL bitflags too in addition to the present bitflag.
So the kernel page fault can keep using the regular
pte_present/pmd_present/pmd_huge.
The confusion arises because _PAGE_GLOBAL and _PAGE_PROTNONE are
sharing the same bit, and in the pmd case we pretend _PAGE_PSE
to be set only in present pmds (to facilitate split_huge_page
final tlb flush).
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If we aren't debugging per_cpu maps, the cpu's node is stored in
per_cpu variable numa_node. If `node' is NUMA_NO_NODE, it means
the caller wants to clear the cpu's node. So we should also
call set_cpu_numa_node() in this case.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ftruncate() doesn't - it's declared with size as unsigned long,
but truncate() and lseek() have that argument as signed long.
IOW, these two really need sign extension + branch to native
syscall; argument validation in sys_... does *not* suffice.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The Xtensa architecture provides a global register called THREADPTR
for the purpose of Thread Local Storage (TLS) support. This allows us
to use a fairly simple implementation, keeping the thread pointer in
the regset and simply saving and restoring it upon entering/exiting
the from user space.
Signed-off-by: Chris Zankel <chris@zankel.net>
This fixes the following build errors seen in the linux-next:
arch/xtensa/include/asm/checksum.h:247:2: error: implicit declaration of
function 'access_ok' [-Werror=implicit-function-declaration]
arch/xtensa/include/asm/checksum.h:247:16: error: 'VERIFY_WRITE' undeclared
(first use in this function)
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Now that drivers/gpio/devres.c build does not depend on GPIOLIB do not
enable GENERIC_GPIO by default to fix the following build errors seen
in the linux-next:
include/asm-generic/gpio.h:270:2: error: implicit declaration of function
'__gpio_get_value' [-Werror=implicit-function-declaration]
include/asm-generic/gpio.h:276:2: error: implicit declaration of function
'__gpio_set_value' [-Werror=implicit-function-declaration]
include/linux/gpio.h:60:19: error: redefinition of 'gpio_cansleep'
include/linux/gpio.h:62:2: error: implicit declaration of function
'__gpio_cansleep' [-Werror=implicit-function-declaration]
include/linux/gpio.h:67:2: error: implicit declaration of function
'__gpio_to_irq' [-Werror=implicit-function-declaration]
drivers/gpio/devres.c:26:2: error: implicit declaration of function
'gpio_free' [-Werror=implicit-function-declaration]
drivers/gpio/devres.c:60:2: error: implicit declaration of function
'gpio_request' [-Werror=implicit-function-declaration]
drivers/gpio/devres.c:90:2: error: implicit declaration of function
'gpio_request_one' [-Werror=implicit-function-declaration]
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Compute WindowBase and WindowMask registers correctly on ptrace calls.
Work done earlier by Maxim, Christian and Marc.
Signed-off-by: Marc Gauthier <marc@tensilica.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Support call graph profiling.
Keep upper two bits of PC unchanged through backtrace rather than take
them from sp (a1). The stack pointer is usually in the same GB (same
upper 2 bits) as PC, but technically doesn't always have to be (and
might not in the future, when taking full advantage of MMU v3).
Signed-off-by: Dan Nicolaescu <dann@xtensa-linux.org>
Signed-off-by: Pete Delaney <piet@tensilica.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Simdisk is a block device that maps to a file in the host file system.
It is usable for testing in the simulated environment, like xt-sim or
QEMU. Device binding to host file may be changed at runtime via proc
interface provided the device is not in use. Number of block devices
and initial binding to host files is controlled via kernel/module
parameters, with defaults specified in the kernel configuration.
Signed-off-by: Victor Prupis <vnp@tensilica.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
str[n]cmp functions return negative value if the first string is less
than the second, positive value if the first string is greater than the
second and zero if they are equal. This is important when these
functions are used for sorting/binary search.
With incorrect strcmp return value bsearch was always failing in the
find_symbol_in_section making it impossible to load any module.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Provide arch_get_unmapped_area function aligning shared memory mapping
addresses to the biggest of the page size or the cache way size. That
guarantees that corresponding virtual addresses of shared mappings are
cached by the same cache sets.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
This fixes the following build error in the current linux-next:
include/linux/signal.h:261:2: error: unknown type name '__sigrestore_t'
make[2]: *** [arch/xtensa/kernel/asm-offsets.s] Error 1
make[1]: *** [prepare0] Error 2
make: *** [sub-make] Error 2
that appeared after 32dae82 'consolidate kernel-side struct sigaction declarations'
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
shmctl may be called with IPC_64 flag, select function version of
ipc_parse_version to correctly handle that.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Add support for dispatching medium-priority interrupts, that is,
interrupts of priority levels 2 to EXCM_LEVEL. IRQ handling may be
preempted by higher priority IRQ.
Signed-off-by: Marc Gauthier <marc@tensilica.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
The Diamond 233L processor is a pre-configured Xtensa processor tailored
for Linux application.
Signed-off-by: Pete Delaney <piet@tensilica.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes xtensa to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires moving parts of arch/xtensa/boot/Makefile into newly
created arch/xtensa/boot/dts/Makefile, and updating arch/xtensa/Makefile
to call the new Makefile.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
This rename happened in 79d1c71 powerpc+of: Rename the drivers/of prom_*
functions to of_*.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Pull signal handling cleanups from Al Viro:
"This is the first pile; another one will come a bit later and will
contain SYSCALL_DEFINE-related patches.
- a bunch of signal-related syscalls (both native and compat)
unified.
- a bunch of compat syscalls switched to COMPAT_SYSCALL_DEFINE
(fixing several potential problems with missing argument
validation, while we are at it)
- a lot of now-pointless wrappers killed
- a couple of architectures (cris and hexagon) forgot to save
altstack settings into sigframe, even though they used the
(uninitialized) values in sigreturn; fixed.
- microblaze fixes for delivery of multiple signals arriving at once
- saner set of helpers for signal delivery introduced, several
architectures switched to using those."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (143 commits)
x86: convert to ksignal
sparc: convert to ksignal
arm: switch to struct ksignal * passing
alpha: pass k_sigaction and siginfo_t using ksignal pointer
burying unused conditionals
make do_sigaltstack() static
arm64: switch to generic old sigaction() (compat-only)
arm64: switch to generic compat rt_sigaction()
arm64: switch compat to generic old sigsuspend
arm64: switch to generic compat rt_sigqueueinfo()
arm64: switch to generic compat rt_sigpending()
arm64: switch to generic compat rt_sigprocmask()
arm64: switch to generic sigaltstack
sparc: switch to generic old sigsuspend
sparc: COMPAT_SYSCALL_DEFINE does all sign-extension as well as SYSCALL_DEFINE
sparc: kill sign-extending wrappers for native syscalls
kill sparc32_open()
sparc: switch to use of generic old sigaction
sparc: switch sys_compat_rt_sigaction() to COMPAT_SYSCALL_DEFINE
mips: switch to generic sys_fork() and sys_clone()
...
Merge second patch-bomb from Andrew Morton:
- A little DM fix
- the MM queue
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (154 commits)
ksm: allocate roots when needed
mm: cleanup "swapcache" in do_swap_page
mm,ksm: swapoff might need to copy
mm,ksm: FOLL_MIGRATION do migration_entry_wait
ksm: shrink 32-bit rmap_item back to 32 bytes
ksm: treat unstable nid like in stable tree
ksm: add some comments
tmpfs: fix mempolicy object leaks
tmpfs: fix use-after-free of mempolicy object
mm/fadvise.c: drain all pagevecs if POSIX_FADV_DONTNEED fails to discard all pages
mm: export mmu notifier invalidates
mm: accelerate mm_populate() treatment of THP pages
mm: use long type for page counts in mm_populate() and get_user_pages()
mm: accurately document nr_free_*_pages functions with code comments
HWPOISON: change order of error_states[]'s elements
HWPOISON: fix misjudgement of page_action() for errors on mlocked pages
memcg: stop warning on memcg_propagate_kmem
net: change type of virtio_chan->p9_max_pages
vmscan: change type of vm_total_pages to unsigned long
fs/nfsd: change type of max_delegations, nfsd_drc_max_mem and nfsd_drc_mem_used
...
Now the function nr_free_buffer_pages returns unsigned long, so use %ld
to print its return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swap_lock is heavily contended when I test swap to 3 fast SSD (even
slightly slower than swap to 2 such SSD). The main contention comes
from swap_info_get(). This patch tries to fix the gap with adding a new
per-partition lock.
Global data like nr_swapfiles, total_swap_pages, least_priority and
swap_list are still protected by swap_lock.
nr_swap_pages is an atomic now, it can be changed without swap_lock. In
theory, it's possible get_swap_page() finds no swap pages but actually
there are free swap pages. But sounds not a big problem.
Accessing partition specific data (like scan_swap_map and so on) is only
protected by swap_info_struct.lock.
Changing swap_info_struct.flags need hold swap_lock and
swap_info_struct.lock, because scan_scan_map() will check it. read the
flags is ok with either the locks hold.
If both swap_lock and swap_info_struct.lock must be hold, we always hold
the former first to avoid deadlock.
swap_entry_free() can change swap_list. To delete that code, we add a
new highest_priority_index. Whenever get_swap_page() is called, we
check it. If it's valid, we use it.
It's a pity get_swap_page() still holds swap_lock(). But in practice,
swap_lock() isn't heavily contended in my test with this patch (or I can
say there are other much more heavier bottlenecks like TLB flush). And
BTW, looks get_swap_page() doesn't really need the lock. We never free
swap_info[] and we check SWAP_WRITEOK flag. The only risk without the
lock is we could swapout to some low priority swap, but we can quickly
recover after several rounds of swap, so sounds not a big deal to me.
But I'd prefer to fix this if it's a real problem.
"swap: make each swap partition have one address_space" improved the
swapout speed from 1.7G/s to 2G/s. This patch further improves the
speed to 2.3G/s, so around 15% improvement. It's a multi-process test,
so TLB flush isn't the biggest bottleneck before the patches.
[arnd@arndb.de: fix it for nommu]
[hughd@google.com: add missing unlock]
[minchan@kernel.org: get rid of lockdep whinge on sys_swapon]
Signed-off-by: Shaohua Li <shli@fusionio.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Dan Magenheimer <dan.magenheimer@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now provide an option for users who don't want to specify physical
memory address in kernel commandline.
/*
* For movablemem_map=acpi:
*
* SRAT: |_____| |_____| |_________| |_________| ......
* node id: 0 1 1 2
* hotpluggable: n y y n
* movablemem_map: |_____| |_________|
*
* Using movablemem_map, we can prevent memblock from allocating memory
* on ZONE_MOVABLE at boot time.
*/
So user just specify movablemem_map=acpi, and the kernel will use
hotpluggable info in SRAT to determine which memory ranges should be set
as ZONE_MOVABLE.
If all the memory ranges in SRAT is hotpluggable, then no memory can be
used by kernel. But before parsing SRAT, memblock has already reserve
some memory ranges for other purposes, such as for kernel image, and so
on. We cannot prevent kernel from using these memory. So we need to
exclude these ranges even if these memory is hotpluggable.
Furthermore, there could be several memory ranges in the single node
which the kernel resides in. We may skip one range that have memory
reserved by memblock, but if the rest of memory is too small, then the
kernel will fail to boot. So, make the whole node which the kernel
resides in un-hotpluggable. Then the kernel has enough memory to use.
NOTE: Using this way will cause NUMA performance down because the
whole node will be set as ZONE_MOVABLE, and kernel cannot use memory
on it. If users don't want to lose NUMA performance, just don't use
it.
[akpm@linux-foundation.org: fix warning]
[akpm@linux-foundation.org: use strcmp()]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When implementing movablemem_map boot option, we introduced an array
movablemem_map.map[] to store the memory ranges to be set as
ZONE_MOVABLE.
Since ZONE_MOVABLE is the latst zone of a node, if user didn't specify
the whole node memory range, we need to extend it to the node end so
that we can use it to prevent memblock from allocating memory in the
ranges user didn't specify.
We now implement movablemem_map boot option like this:
/*
* For movablemem_map=nn[KMG]@ss[KMG]:
*
* SRAT: |_____| |_____| |_________| |_________| ......
* node id: 0 1 1 2
* user specified: |__| |___|
* movablemem_map: |___| |_________| |______| ......
*
* Using movablemem_map, we can prevent memblock from allocating memory
* on ZONE_MOVABLE at boot time.
*
* NOTE: In this case, SRAT info will be ingored.
*/
[akpm@linux-foundation.org: clean up code, fix build warning]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On linux, the pages used by kernel could not be migrated. As a result,
if a memory range is used by kernel, it cannot be hot-removed. So if we
want to hot-remove memory, we should prevent kernel from using it.
The way now used to prevent this is specify a memory range by
movablemem_map boot option and set it as ZONE_MOVABLE.
But when the system is booting, memblock will allocate memory, and
reserve the memory for kernel. And before we parse SRAT, and know the
node memory ranges, memblock is working. And it may allocate memory in
ranges to be set as ZONE_MOVABLE. This memory can be used by kernel,
and never be freed.
So, let's parse SRAT before memblock is called first. And it is early
enough.
The first call of memblock_find_in_range_node() is in:
setup_arch()
|-->setup_real_mode()
so, this patch add a function early_parse_srat() to parse SRAT, and call
it before setup_real_mode() is called.
NOTE:
1) early_parse_srat() is called before numa_init(), and has initialized
numa_meminfo. So DO NOT clear numa_nodes_parsed in numa_init() and DO
NOT zero numa_meminfo in numa_init(), otherwise we will lose memory
numa info.
2) I don't know why using count of memory affinities parsed from SRAT
as a return value in original acpi_numa_init(). So I add a static
variable srat_mem_cnt to remember this count and use it as the return
value of the new acpi_numa_init()
[mhocko@suse.cz: parse SRAT before memblock is ready fix]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the implementation of SRAT support, we met a problem. In
setup_arch(), we have the following call series:
1) memblock is ready;
2) some functions use memblock to allocate memory;
3) parse ACPI tables, such as SRAT.
Before 3), we don't know which memory is hotpluggable, and as a result,
we cannot prevent memblock from allocating hotpluggable memory. So, in
2), there could be some hotpluggable memory allocated by memblock.
Now, we are trying to parse SRAT earlier, before memblock is ready. But
I think we need more investigation on this topic. So in this v5, I
dropped all the SRAT support, and v5 is just the same as v3, and it is
based on 3.8-rc3.
As we planned, we will support getting info from SRAT without users'
participation at last. And we will post another patch-set to do so.
And also, I think for now, we can add this boot option as the first step
of supporting movable node. Since Linux cannot migrate the direct
mapped pages, the only way for now is to limit the whole node containing
only movable memory.
Using SRAT is one way. But even if we can use SRAT, users still need an
interface to enable/disable this functionality if they don't want to
loose their NUMA performance. So I think, a user interface is always
needed.
For now, users can disable this functionality by not specifying the boot
option. Later, we will post SRAT support, and add another option value
"movablecore_map=acpi" to using SRAT.
This patch:
If system can create movable node which all memory of the node is
allocated as ZONE_MOVABLE, setup_node_data() cannot allocate memory for
the node's pg_data_t. So, use memblock_alloc_try_nid() instead of
memblock_alloc_nid() to retry when the first allocation fails.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the node is offlined, there is no memory/cpu on the node. If a
sleep task runs on a cpu of this node, it will be migrated to the cpu on
the other node. So we can clear cpu-to-node mapping.
[akpm@linux-foundation.org: numa_clear_node() and numa_set_node() can no longer be __cpuinit]
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a cpu is hotpluged, we call acpi_map_cpu2node() in
_acpi_map_lsapic() to store the cpu's node and apicid's node. But we
don't clear the cpu's node in acpi_unmap_lsapic() when this cpu is
hotremoved. If the node is also hotremoved, we will get the following
messages:
kernel BUG at include/linux/gfp.h:329!
invalid opcode: 0000 [#1] SMP
Modules linked in: ebtable_nat ebtables ipt_MASQUERADE iptable_nat nf_nat xt_CHECKSUM iptable_mangle bridge stp llc sunrpc ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables binfmt_misc dm_mirror dm_region_hash dm_log dm_mod vhost_net macvtap macvlan tun uinput iTCO_wdt iTCO_vendor_support coretemp kvm_intel kvm crc32c_intel microcode pcspkr i2c_i801 i2c_core lpc_ich mfd_core ioatdma e1000e i7core_edac edac_core sg acpi_memhotplug igb dca sd_mod crc_t10dif megaraid_sas mptsas mptscsih mptbase scsi_transport_sas scsi_mod
Pid: 3126, comm: init Not tainted 3.6.0-rc3-tangchen-hostbridge+ #13 FUJITSU-SV PRIMEQUEST 1800E/SB
RIP: 0010:[<ffffffff811bc3fd>] [<ffffffff811bc3fd>] allocate_slab+0x28d/0x300
RSP: 0018:ffff88078a049cf8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000001 RDI: 0000000000000246
RBP: ffff88078a049d38 R08: 00000000000040d0 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000b5f R12: 00000000000052d0
R13: ffff8807c1417300 R14: 0000000000030038 R15: 0000000000000003
FS: 00007fa9b1b44700(0000) GS:ffff8807c3800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007fa9b09acca0 CR3: 000000078b855000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process init (pid: 3126, threadinfo ffff88078a048000, task ffff8807bb6f2650)
Call Trace:
new_slab+0x30/0x1b0
__slab_alloc+0x358/0x4c0
kmem_cache_alloc_node_trace+0xb4/0x1e0
alloc_fair_sched_group+0xd0/0x1b0
sched_create_group+0x3e/0x110
sched_autogroup_create_attach+0x4d/0x180
sys_setsid+0xd4/0xf0
system_call_fastpath+0x16/0x1b
Code: 89 c4 e9 73 fe ff ff 31 c0 89 de 48 c7 c7 45 de 9e 81 44 89 45 c8 e8 22 05 4b 00 85 db 44 8b 45 c8 0f 89 4f ff ff ff 0f 0b eb fe <0f> 0b 90 eb fd 0f 0b eb fe 89 de 48 c7 c7 45 de 9e 81 31 c0 44
RIP [<ffffffff811bc3fd>] allocate_slab+0x28d/0x300
RSP <ffff88078a049cf8>
---[ end trace adf84c90f3fea3e5 ]---
The reason is that the cpu's node is not NUMA_NO_NODE, we will call
alloc_pages_exact_node() to alloc memory on the node, but the node is
offlined.
If the node is onlined, we still need cpu's node. For example: a task
on the cpu is sleeped when the cpu is hotremoved. We will choose
another cpu to run this task when it is waked up. If we know the cpu's
node, we will choose the cpu on the same node first. So we should clear
cpu-to-node mapping when the node is offlined.
This patch only clears apicid-to-node mapping when the cpu is
hotremoved.
[akpm@linux-foundation.org: fix section error]
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a new API vmemmap_free() to free and remove vmemmap
pagetables. Since pagetable implements are different, each architecture
has to provide its own version of vmemmap_free(), just like
vmemmap_populate().
Note: vmemmap_free() is not implemented for ia64, ppc, s390, and sparc.
[mhocko@suse.cz: fix implicit declaration of remove_pagetable]
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When memory is removed, the corresponding pagetables should alse be
removed. This patch introduces some common APIs to support vmemmap
pagetable and x86_64 architecture direct mapping pagetable removing.
All pages of virtual mapping in removed memory cannot be freed if some
pages used as PGD/PUD include not only removed memory but also other
memory. So this patch uses the following way to check whether a page
can be freed or not.
1) When removing memory, the page structs of the removed memory are
filled with 0FD.
2) All page structs are filled with 0xFD on PT/PMD, PT/PMD can be
cleared. In this case, the page used as PT/PMD can be freed.
For direct mapping pages, update direct_pages_count[level] when we freed
their pagetables. And do not free the pages again because they were
freed when offlining.
For vmemmap pages, free the pages and their pagetables.
For larger pages, do not split them into smaller ones because there is
no way to know if the larger page has been split. As a result, there is
no way to decide when to split. We deal the larger pages in the
following way:
1) For direct mapped pages, all the pages were freed when they were
offlined. And since menmory offline is done section by section, all
the memory ranges being removed are aligned to PAGE_SIZE. So only need
to deal with unaligned pages when freeing vmemmap pages.
2) For vmemmap pages being used to store page_struct, if part of the
larger page is still in use, just fill the unused part with 0xFD. And
when the whole page is fulfilled with 0xFD, then free the larger page.
[akpm@linux-foundation.org: fix typo in comment]
[tangchen@cn.fujitsu.com: do not calculate direct mapping pages when freeing vmemmap pagetables]
[tangchen@cn.fujitsu.com: do not free direct mapping pages twice]
[tangchen@cn.fujitsu.com: do not free page split from hugepage one by one]
[tangchen@cn.fujitsu.com: do not split pages when freeing pagetable pages]
[akpm@linux-foundation.org: use pmd_page_vaddr()]
[akpm@linux-foundation.org: fix used-uninitialised bug]
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For removing memmap region of sparse-vmemmap which is allocated bootmem,
memmap region of sparse-vmemmap needs to be registered by
get_page_bootmem(). So the patch searches pages of virtual mapping and
registers the pages by get_page_bootmem().
NOTE: register_page_bootmem_memmap() is not implemented for ia64,
ppc, s390, and sparc. So introduce CONFIG_HAVE_BOOTMEM_INFO_NODE
and revert register_page_bootmem_info_node() when platform doesn't
support it.
It's implemented by adding a new Kconfig option named
CONFIG_HAVE_BOOTMEM_INFO_NODE, which will be automatically selected
by memory-hotplug feature fully supported archs(currently only on
x86_64).
Since we have 2 config options called MEMORY_HOTPLUG and
MEMORY_HOTREMOVE used for memory hot-add and hot-remove separately,
and codes in function register_page_bootmem_info_node() are only
used for collecting infomation for hot-remove, so reside it under
MEMORY_HOTREMOVE.
Besides page_isolation.c selected by MEMORY_ISOLATION under
MEMORY_HOTPLUG is also such case, move it too.
[mhocko@suse.cz: put register_page_bootmem_memmap inside CONFIG_MEMORY_HOTPLUG_SPARSE]
[linfeng@cn.fujitsu.com: introduce CONFIG_HAVE_BOOTMEM_INFO_NODE and revert register_page_bootmem_info_node()]
[mhocko@suse.cz: remove the arch specific functions without any implementation]
[linfeng@cn.fujitsu.com: mm/Kconfig: move auto selects from MEMORY_HOTPLUG to MEMORY_HOTREMOVE as needed]
[rientjes@google.com: fix defined but not used warning]
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Wu Jianguo <wujianguo@huawei.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Lin Feng <linfeng@cn.fujitsu.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For removing memory, we need to remove page tables. But it depends on
architecture. So the patch introduce arch_remove_memory() for removing
page table. Now it only calls __remove_pages().
Note: __remove_pages() for some archtecuture is not implemented
(I don't know how to implement it for s390).
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the MAP_POPULATE handling has been moved to mmap_region() call
sites, the only remaining use of the flags argument is to pass the
MAP_NORESERVE flag. This can be just as easily handled by
do_mmap_pgoff(), so do that and remove the mmap_region() flags
parameter.
[akpm@linux-foundation.org: remove double parens]
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Greg Ungerer <gregungerer@westnet.com.au>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull powerpc updates from Benjamin Herrenschmidt:
"So from the depth of frozen Minnesota, here's the powerpc pull request
for 3.9. It has a few interesting highlights, in addition to the
usual bunch of bug fixes, minor updates, embedded device tree updates
and new boards:
- Hand tuned asm implementation of SHA1 (by Paulus & Michael
Ellerman)
- Support for Doorbell interrupts on Power8 (kind of fast
thread-thread IPIs) by Ian Munsie
- Long overdue cleanup of the way we handle relocation of our open
firmware trampoline (prom_init.c) on 64-bit by Anton Blanchard
- Support for saving/restoring & context switching the PPR (Processor
Priority Register) on server processors that support it. This
allows the kernel to preserve thread priorities established by
userspace. By Haren Myneni.
- DAWR (new watchpoint facility) support on Power8 by Michael Neuling
- Ability to change the DSCR (Data Stream Control Register) which
controls cache prefetching on a running process via ptrace by
Alexey Kardashevskiy
- Support for context switching the TAR register on Power8 (new
branch target register meant to be used by some new specific
userspace perf event interrupt facility which is yet to be enabled)
by Ian Munsie.
- Improve preservation of the CFAR register (which captures the
origin of a branch) on various exception conditions by Paulus.
- Move the Bestcomm DMA driver from arch powerpc to drivers/dma where
it belongs by Philippe De Muyter
- Support for Transactional Memory on Power8 by Michael Neuling
(based on original work by Matt Evans). For those curious about
the feature, the patch contains a pretty good description."
(See commit db8ff907027b: "powerpc: Documentation for transactional
memory on powerpc" for the mentioned description added to the file
Documentation/powerpc/transactional_memory.txt)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (140 commits)
powerpc/kexec: Disable hard IRQ before kexec
powerpc/85xx: l2sram - Add compatible string for BSC9131 platform
powerpc/85xx: bsc9131 - Correct typo in SDHC device node
powerpc/e500/qemu-e500: enable coreint
powerpc/mpic: allow coreint to be determined by MPIC version
powerpc/fsl_pci: Store the pci ctlr device ptr in the pci ctlr struct
powerpc/85xx: Board support for ppa8548
powerpc/fsl: remove extraneous DIU platform functions
arch/powerpc/platforms/85xx/p1022_ds.c: adjust duplicate test
powerpc: Documentation for transactional memory on powerpc
powerpc: Add transactional memory to pseries and ppc64 defconfigs
powerpc: Add config option for transactional memory
powerpc: Add transactional memory to POWER8 cpu features
powerpc: Add new transactional memory state to the signal context
powerpc: Hook in new transactional memory code
powerpc: Routines for FP/VSX/VMX unavailable during a transaction
powerpc: Add transactional memory unavaliable execption handler
powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes
powerpc: Add FP/VSX and VMX register load functions for transactional memory
powerpc: Add helper functions for transactional memory context switching
...
Disable hard IRQ before kexec a new kernel image.
Not doing it can result in corrupted data in the memory segments
reserved for the new kernel.
Signed-off-by: Phileas Fogg <phileas-fogg@mail.ru>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On multiplatform kernels, $MACHINE will be empty so there will be no
default LOADADDR. Fail to build the uImage target unless one is provided by the
developer at build time.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull parisc updates from Helge Deller.
The bulk of this is optimized page coping/clearing and cache flushing
(virtual caches are lovely) by John David Anglin.
* 'parisc-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (31 commits)
arch/parisc/include/asm: use ARRAY_SIZE macro in mmzone.h
parisc: remove empty lines and unnecessary #ifdef coding in include/asm/signal.h
parisc: sendfile and sendfile64 syscall cleanups
parisc: switch to available compat_sched_rr_get_interval implementation
parisc: fix fallocate syscall
parisc: fix error return codes for rt_sigaction and rt_sigprocmask
parisc: convert msgrcv and msgsnd syscalls to use compat layer
parisc: correctly wire up mq_* functions for CONFIG_COMPAT case
parisc: fix personality on 32bit kernel
parisc: wire up process_vm_readv, process_vm_writev, kcmp and finit_module syscalls
parisc: led driver requires CONFIG_VM_EVENT_COUNTERS
parisc: remove unused compat_rt_sigframe.h header
parisc/mm/fault.c: Port OOM changes to do_page_fault
parisc: space register variables need to be in native length (unsigned long)
parisc: fix ptrace breakage
parisc: always detect multiple physical ranges
parisc: ensure that mmapped shared pages are aligned at SHMLBA addresses
parisc: disable preemption while flushing D- or I-caches through TMPALIAS region
parisc: remove IRQF_DISABLED
parisc: fixes and cleanups in page cache flushing (4/4)
...
Allocating a file structure in function get_empty_filp() might fail because
of several reasons:
- not enough memory for file structures
- operation is not allowed
- user is over its limit
Currently the function returns NULL in all cases and we loose the exact
reason of the error. All callers of get_empty_filp() assume that the function
can fail with ENFILE only.
Return error through pointer. Change all callers to preserve this error code.
[AV: cleaned up a bit, carved the get_empty_filp() part out into a separate commit
(things remaining here deal with alloc_file()), removed pipe(2) behaviour change]
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Reviewed-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull x86 microcode loading update from Peter Anvin:
"This patchset lets us update the CPU microcode very, very early in
initialization if the BIOS fails to do so (never happens, right?)
This is handy for dealing with things like the Atom erratum where we
have to run without PSE because microcode loading happens too late.
As I mentioned in the x86/mm push request it depends on that
infrastructure but it is otherwise a standalone feature."
* 'x86/microcode' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Make early microcode loading a configuration feature
x86/mm/init.c: Copy ucode from initrd image to kernel memory
x86/head64.c: Early update ucode in 64-bit
x86/head_32.S: Early update ucode in 32-bit
x86/microcode_intel_early.c: Early update ucode on Intel's CPU
x86/tlbflush.h: Define __native_flush_tlb_global_irq_disabled()
x86/microcode_intel_lib.c: Early update ucode on Intel's CPU
x86/microcode_core_early.c: Define interfaces for early loading ucode
x86/common.c: load ucode in 64 bit or show loading ucode info in 32 bit on AP
x86/common.c: Make have_cpuid_p() a global function
x86/microcode_intel.h: Define functions and macros for early loading ucode
x86, doc: Documentation for early microcode loading
With commit 8170e6bed4 ("x86, 64bit: Use a #PF handler to materialize
early mappings on demand") we started hitting an early bootup crash
where the Xen hypervisor would inform us that:
(XEN) d7:v0: unhandled page fault (ec=0000)
(XEN) Pagetable walk from ffffea000005b2d0:
(XEN) L4[0x1d4] = 0000000000000000 ffffffffffffffff
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 7 (vcpu#0) crashed on cpu#3:
(XEN) ----[ Xen-4.2.0 x86_64 debug=n Not tainted ]----
.. that Xen was unable to context switch back to dom0.
Looking at the calling stack we find:
[<ffffffff8103feba>] xen_get_user_pgd+0x5a <--
[<ffffffff8103feba>] xen_get_user_pgd+0x5a
[<ffffffff81042d27>] xen_write_cr3+0x77
[<ffffffff81ad2d21>] init_mem_mapping+0x1f9
[<ffffffff81ac293f>] setup_arch+0x742
[<ffffffff81666d71>] printk+0x48
We are trying to figure out whether we need to up-date the user PGD as
well. Please keep in mind that under 64-bit PV guests we have a limited
amount of rings: 0 for the Hypervisor, and 1 for both the Linux kernel
and user-space. As such the Linux pvops'fied version of write_cr3
checks if it has to update the user-space cr3 as well.
That clearly is not needed during early bootup. The recent changes (see
above git commit) streamline the x86 page table allocation to be much
simpler (And also incidentally the #PF handler ends up in spirit being
similar to how the Xen toolstack sets up the initial page-tables).
The fix is to have an early-bootup version of cr3 that just loads the
kernel %cr3. The later version - which also handles user-page
modifications will be used after the initial page tables have been
setup.
[ hpa: removed a redundant #ifdef and made the new function __init.
Also note that x86-32 already has such an early xen_write_cr3. ]
Tested-by: "H. Peter Anvin" <hpa@zytor.com>
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1361579812-23709-1-git-send-email-konrad.wilk@oracle.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit def8203 ("microblaze idle: delete pm_idle") introduced the following
compile error:
arch/microblaze/kernel/process.c: In function 'cpu_idle':
arch/microblaze/kernel/process.c💯 error: 'idle' undeclared (first use in this function)
arch/microblaze/kernel/process.c💯 error: (Each undeclared identifier is reported only once
arch/microblaze/kernel/process.c💯 error: for each function it appears in.)
arch/microblaze/kernel/process.c:106: error: implicit declaration of function 'idle'
This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 26bab0c ("blackfin idle: delete pm_idle") introduced the following
compile error:
arch/blackfin/kernel/process.c: In function ‘cpu_idle’:
arch/blackfin/kernel/process.c:83: error: ‘idle’ undeclared (first use in this function)
arch/blackfin/kernel/process.c:83: error: (Each undeclared identifier is reported only once
arch/blackfin/kernel/process.c:83: error: for each function it appears in.)
arch/blackfin/kernel/process.c:88: error: implicit declaration of function ‘idle’
This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update the ia64 hugetlb_get_unmapped_area function to make use of
vm_unmapped_area() instead of implementing a brute force search.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update the ia64 arch_get_unmapped_area function to make use of
vm_unmapped_area() instead of implementing a brute force search.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The code requires the use of the proper per-exception-vector stub
functions (set up as the early_idt_handlers[] array - note the 's') that
make sure to set up the error vector number. This is true regardless of
whether CONFIG_EARLY_PRINTK is set or not.
Why? The stack offset for the comparison of __KERNEL_CS won't be right
otherwise, nor will the new check (from commit 8170e6bed465: "x86,
64bit: Use a #PF handler to materialize early mappings on demand") for
the page fault exception vector.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An architecture should not unconditionally enable 'GENERIC_GPIO'
without providing an implementation. In case of arm64, selecting
ARCH_WANT_OPTIONAL_GPIOLIB is the right solution, because it
lets us enable GPIOLIB when configuring the kernel, and that
implicitly turns on GENERIC_GPIO.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Conflicts:
include/linux/ssb/ssb_driver_gige.h
Also resolves a logical merge conflict in drivers/net/ethernet/broadcom/-
bgmac.c due to change of an API.
Pull x86 mm changes from Peter Anvin:
"This is a huge set of several partly interrelated (and concurrently
developed) changes, which is why the branch history is messier than
one would like.
The *really* big items are two humonguous patchsets mostly developed
by Yinghai Lu at my request, which completely revamps the way we
create initial page tables. In particular, rather than estimating how
much memory we will need for page tables and then build them into that
memory -- a calculation that has shown to be incredibly fragile -- we
now build them (on 64 bits) with the aid of a "pseudo-linear mode" --
a #PF handler which creates temporary page tables on demand.
This has several advantages:
1. It makes it much easier to support things that need access to data
very early (a followon patchset uses this to load microcode way
early in the kernel startup).
2. It allows the kernel and all the kernel data objects to be invoked
from above the 4 GB limit. This allows kdump to work on very large
systems.
3. It greatly reduces the difference between Xen and native (Xen's
equivalent of the #PF handler are the temporary page tables created
by the domain builder), eliminating a bunch of fragile hooks.
The patch series also gets us a bit closer to W^X.
Additional work in this pull is the 64-bit get_user() work which you
were also involved with, and a bunch of cleanups/speedups to
__phys_addr()/__pa()."
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (105 commits)
x86, mm: Move reserving low memory later in initialization
x86, doc: Clarify the use of asm("%edx") in uaccess.h
x86, mm: Redesign get_user with a __builtin_choose_expr hack
x86: Be consistent with data size in getuser.S
x86, mm: Use a bitfield to mask nuisance get_user() warnings
x86/kvm: Fix compile warning in kvm_register_steal_time()
x86-32: Add support for 64bit get_user()
x86-32, mm: Remove reference to alloc_remap()
x86-32, mm: Remove reference to resume_map_numa_kva()
x86-32, mm: Rip out x86_32 NUMA remapping code
x86/numa: Use __pa_nodebug() instead
x86: Don't panic if can not alloc buffer for swiotlb
mm: Add alloc_bootmem_low_pages_nopanic()
x86, 64bit, mm: hibernate use generic mapping_init
x86, 64bit, mm: Mark data/bss/brk to nx
x86: Merge early kernel reserve for 32bit and 64bit
x86: Add Crash kernel low reservation
x86, kdump: Remove crashkernel range find limit for 64bit
memblock: Add memblock_mem_size()
x86, boot: Not need to check setup_header version for setup_data
...
Pull x86 cpu updates from Peter Anvin:
"This is a corrected attempt at the x86/cpu branch, this time with the
fixes in that makes it not break on KVM (current or past), or any
other virtualizer which traps on this configuration.
Again, the biggest change here is enabling the WC+ memory type on AMD
processors, if the BIOS doesn't."
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, kvm: Add MSR_AMD64_BU_CFG2 to the list of ignored MSRs
x86, cpu, amd: Fix WC+ workaround for older virtual hosts
x86, AMD: Enable WC+ memory type on family 10 processors
x86, AMD: Clean up init_amd()
x86/process: Change %8s to %s for pr_warn() in release_thread()
x86/cpu/hotplug: Remove CONFIG_EXPERIMENTAL dependency
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
Merge misc patches from Andrew Morton:
- Florian has vanished so I appear to have become fbdev maintainer
again :(
- Joel and Mark are distracted to welcome to the new OCFS2 maintainer
- The backlight queue
- Small core kernel changes
- lib/ updates
- The rtc queue
- Various random bits
* akpm: (164 commits)
rtc: rtc-davinci: use devm_*() functions
rtc: rtc-max8997: use devm_request_threaded_irq()
rtc: rtc-max8907: use devm_request_threaded_irq()
rtc: rtc-da9052: use devm_request_threaded_irq()
rtc: rtc-wm831x: use devm_request_threaded_irq()
rtc: rtc-tps80031: use devm_request_threaded_irq()
rtc: rtc-lp8788: use devm_request_threaded_irq()
rtc: rtc-coh901331: use devm_clk_get()
rtc: rtc-vt8500: use devm_*() functions
rtc: rtc-tps6586x: use devm_request_threaded_irq()
rtc: rtc-imxdi: use devm_clk_get()
rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug()
rtc: rtc-pcf8583: use dev_warn() instead of printk()
rtc: rtc-sun4v: use pr_warn() instead of printk()
rtc: rtc-vr41xx: use dev_info() instead of printk()
rtc: rtc-rs5c313: use pr_err() instead of printk()
rtc: rtc-at91rm9200: use dev_dbg()/dev_err() instead of printk()/pr_debug()
rtc: rtc-rs5c372: use dev_dbg()/dev_warn() instead of printk()/pr_debug()
rtc: rtc-ds2404: use dev_err() instead of printk()
rtc: rtc-efi: use dev_err()/dev_warn()/pr_err() instead of printk()
...
The Armada 370 and Armada XP Socs have the same controller that the one
used in the orion platforms. This patch updates the device tree for
these SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the alpha arch_get_unmapped_area function to make use of
vm_unmapped_area() instead of implementing a brute force search.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This provides a band-aid to provide stable page writes on jbd without
needing to backport the fixed locking and page writeback bit handling
schemes of jbd2. The band-aid works by using bounce buffers to snapshot
page contents instead of waiting.
For those wondering about the ext3 bandage -- fixing the jbd locking
(which was done as part of ext4dev years ago) is a lot of surgery, and
setting PG_writeback on data pages when we actually hold the page lock
dropped ext3 performance by nearly an order of magnitude. If we're
going to migrate iscsi and raid to use stable page writes, the
complaints about high latency will likely return. We might as well
centralize their page snapshotting thing to one place.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On cris-linux-gcc, __SIZE_TYPE__ expands to "unsigned int", as
gcc-4.6.3-nolibc/cris-linux/lib/gcc/cris-linux/4.6.3/plugin/include/config/cris/linux.h
has
#define SIZE_TYPE "unsigned int"
Hence __kernel_size_t is also "unsigned int". But __kernel_ssize_t is
"long", which has a different base type, causing compiler warnings like:
fs/quota/quota_tree.c:372:4: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type 'ssize_t' [-Wformat]
To fix this, __kernel_ssize_t should be changed to "int". Hence cris can
just use the generic 32-bit versions from include/asm-generic/posix_types.h
for all size-related types.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Hans-Peter Nilsson <hans-peter.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This contains parts of the ARM KVM support that have dependencies on
other patches merged through the arm-soc tree. In combination with
patches coming through Russell's tree, this will finally add full
support for the kernel based virtual machine on ARM, which has
been awaited for some time now.
Further, we now have a separate platform for virtual machines
and qemu booting that is used by both Xen and KVM, separating
these from the Versatile Express reference implementation.
Obviously, this new platform is multiplatform capable so it
can be combined with existing machines in the same kernel.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u9F0
-----END PGP SIGNATURE-----
Merge tag 'virt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM virtualization changes:
"This contains parts of the ARM KVM support that have dependencies on
other patches merged through the arm-soc tree. In combination with
patches coming through Russell's tree, this will finally add full
support for the kernel based virtual machine on ARM, which has been
awaited for some time now.
Further, we now have a separate platform for virtual machines and qemu
booting that is used by both Xen and KVM, separating these from the
Versatile Express reference implementation. Obviously, this new
platform is multiplatform capable so it can be combined with existing
machines in the same kernel."
* tag 'virt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
ARM: arch_timer: include linux/errno.h
arm: arch_timer: add missing inline in stub function
ARM: KVM: arch_timers: Wire the init code and config option
ARM: KVM: arch_timers: Add timer world switch
ARM: KVM: arch_timers: Add guest timer core support
ARM: KVM: Add VGIC configuration option
ARM: KVM: VGIC initialisation code
ARM: KVM: VGIC control interface world switch
ARM: KVM: VGIC interrupt injection
ARM: KVM: vgic: retire queued, disabled interrupts
ARM: KVM: VGIC virtual CPU interface management
ARM: KVM: VGIC distributor handling
ARM: KVM: VGIC accept vcpu and dist base addresses from user space
ARM: KVM: Initial VGIC infrastructure code
ARM: KVM: Keep track of currently running vcpus
KVM: ARM: Introduce KVM_ARM_SET_DEVICE_ADDR ioctl
ARM: gic: add __ASSEMBLY__ guard to C definitions
ARM: gic: define GICH offsets for VGIC support
ARM: gic: add missing distributor defintions
ARM: mach-virt: fixup machine descriptor after removal of sys_timer
...
These are device tree conversions for a number of platforms,
with the intention of turning code from board files into
device tree descriptions. Notable changes are:
* davinci bindings for pinctrl, MTD, RTC, watchdog and i2c
* nomadik bindings for all devices, removing the board files
* bcm2835 bindings for mmc and i2c
* tegra bindings for hdmi, keyboard, audio, as well as some updates
* at91 bindings for hardware ecc and for devices on RM9200
* mxs bindings for cfa100xx
* sunxi support for Miniand Hackberry board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=NLEa
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree conversions from Arnd Bergmann:
"These are device tree conversions for a number of platforms, with the
intention of turning code from board files into device tree
descriptions. Notable changes are:
- davinci bindings for pinctrl, MTD, RTC, watchdog and i2c
- nomadik bindings for all devices, removing the board files
- bcm2835 bindings for mmc and i2c
- tegra bindings for hdmi, keyboard, audio, as well as some updates
- at91 bindings for hardware ecc and for devices on RM9200
- mxs bindings for cfa100xx
- sunxi support for Miniand Hackberry board"
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (72 commits)
Revert "sunxi: a10-cubieboard: Add user LEDs to the device tree"
Revert "sunxi: a13-olinuxino: Add user LED to the device tree"
clk: tegra: initialise parent of uart clocks
ARM: tegra: remove clock-frequency properties from serial nodes
clk: tegra: fix driver to match DT binding
clk: tegra: local arrays should be static
clk: tegra: Add missing spinlock for hclk and pclk
clk: tegra: Implement locking for super clock
clk: tegra: fix wrong clock index between se to sata_cold
sunxi: a13-olinuxino: Add user LED to the device tree
ARM: davinci: da850 DT: add support for machine reboot
ARM: davinci: da850: add wdt DT node
ARM: davinci: da850: add DT node for I2C0
ARM: at91: at91sam9n12: add DT parameters to enable PMECC
ARM: at91: at91sam9x5: add DT parameters to enable PMECC
ARM: at91: add EMAC bindings to RM9200 DT
ARM: at91: add SSC bindings to RM9200 DT
ARM: at91: add MMC bindings to RM9200 DT
ARM: at91: Animeo IP: enable watchdog support
ARM: nomadik: fix OF compilation regression
...
These updates are all for board specific code, including
* defconfig updates for shmobile, davinci, bcm2835, imx, omap and tegra
* SD/MMC and I2C support on bcm2835 (Raspberry PI)
* minor updates for PXA
* shmobile updates to GPIO usage in board files
* More things in OMAP board files are moved over to device tree probing
* Better support for audio devices on some OMAP platforms
Conflicts include the omap board-apollon.c file that is removed without
a replacement, and conflicting context in the 4430sdp board file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/qBE
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board specific changes from Arnd Bergmann:
"These updates are all for board specific code, including
- defconfig updates for shmobile, davinci, bcm2835, imx, omap and
tegra
- SD/MMC and I2C support on bcm2835 (Raspberry PI)
- minor updates for PXA
- shmobile updates to GPIO usage in board files
- More things in OMAP board files are moved over to device tree
probing
- Better support for audio devices on some OMAP platforms"
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: imx_v4_v5_defconfig: Add VPU support
ARM: imx: configs: enable netfilter support
ARM: OMAP2+: Fix twl section warnings related to omap_twl4030_audio_init
ARM: OMAP2+: omap2plus_defconfig: enable omap1 rtc
RX-51: Register twl4030-madc device
RX-51: Add leds lp5523 names from Maemo 5 2.6.28 kernel
ARM: OMAP2+: AM33XX: omap2plus_defconfig: Add support for few drivers
ARM: OMAP1: nokia770: enable CBUS/Retu
ARM: OMAP2+: omap2plus_defconfig: enable CMA allocator
ARM: OMAP2+: omap2plus_defconfig: enable TFP410 chip support
ARM: OMAP3: igep0020: simplify GPIO LEDs dependencies
ARM: OMAP2+: craneboard: support the TPS65910 PMU
ARM: OMAP2+: craneboard: support NAND device
ARM: OMAP3: cm-t3517: add MMC support
ARM: OMAP2+: Remove apollon board support
ARM: shmobile: armadillo800eva: set clock rates before timer init
ARM: tegra: defconfig updates
ARM: shmobile: mackerel: Use gpio_request_one()
ARM: shmobile: kzm9g: Use gpio_request_one()
ARM: shmobile: bonito: Use gpio_request_one()
...
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
Converting more ARM platforms to multiplatform support. This time, OMAP
gets converted, which is a major step since this is by far the largest
platform in terms of code size. The same thing happens to the vt8500
platform.
Conflicts include:
* Two mach/uncompress.h files are removed, the changes made to them
elsewhere can be discarded now.
* Moving the OMAP4 irq_match array has context clashes with turning
omap4_sar_ram_init into an omap_early_initcall()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nl4h
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform support from Arnd Bergmann:
"Converting more ARM platforms to multiplatform support. This time,
OMAP gets converted, which is a major step since this is by far the
largest platform in terms of code size. The same thing happens to the
vt8500 platform."
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
net: cwdavinci_cpdma: export symbols for cpsw
remoteproc: omap: depend on OMAP_MBOX_FWK
[media] davinci: do not include mach/hardware.h
ARM: OMAP2+: Make sure files with omap initcalls include soc.h
ARM: OMAP2+: Include soc.h to drm.c to fix compiling
ARM: OMAP2+: Fix warning for hwspinlock omap_postcore_initcall
ARM: multi_v7_defconfig: add ARCH_ZYNQ
ARM: multi_v7_defconfig: remove unnecessary CONFIG_GPIOLIB
arm: vt8500: Remove remaining mach includes
arm: vt8500: Convert debug-macro.S to be multiplatform friendly
arm: vt8500: Remove single platform Kconfig options
ARM: OMAP2+: Remove now obsolete uncompress.h and debug-macro.S
ARM: OMAP2+: Add minimal support for booting vexpress
ARM: OMAP2+: Enable ARCH_MULTIPLATFORM support
ARM: OMAP2+: Disable code that currently does not work with multiplaform
ARM: OMAP2+: Add multiplatform debug_ll support
ARM: OMAP: Fix dmaengine init for multiplatform
ARM: OMAP: Fix i2c cmdline initcall for multiplatform
ARM: OMAP2+: Use omap initcalls
ARM: OMAP2+: Limit omap initcalls to omap only on multiplatform kernels
* Updates to the ux500 cpufreq code
* Moving the u300 DMA controller driver to drivers/dma
* Moving versatile express drivers out of arch/arm for sharing with arch/arm64
* Device tree bindings for the OMAP General Purpose Memory Controller
There is a simple conflict in drivers/cpufreq/dbx500-cpufreq.c, because
the mach/id.h header and the cpu_is_u8500_family() function in it are
now gone.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=R0p0
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
- Updates to the ux500 cpufreq code
- Moving the u300 DMA controller driver to drivers/dma
- Moving versatile express drivers out of arch/arm for sharing with arch/arm64
- Device tree bindings for the OMAP General Purpose Memory Controller
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: OMAP2+: gpmc: Add device tree documentation for elm handle
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
ARM: OMAP2+: gpmc-onenand: drop __init annotation
mtd: omap-onenand: pass device_node in platform data
ARM: OMAP2+: Prevent potential crash if GPMC probe fails
ARM: OMAP2+: gpmc: Remove unneeded of_node_put()
arm: Move sp810.h to include/linux/amba/
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs
ARM: OMAP: gpmc-nand: drop __init annotation
mtd: omap-nand: pass device_node in platform data
ARM: OMAP: gpmc: don't create devices from initcall on DT
dma: coh901318: cut down on platform data abstraction
dma: coh901318: merge header files
dma: coh901318: push definitions into driver
dma: coh901318: push header down into the DMA subsystem
dma: coh901318: skip hard-coded addresses
dma: coh901318: remove hardcoded target addresses
dma: coh901318: push platform data into driver
dma: coh901318: create a proper platform data file
...
This is another cleanup series, containing the move of the Renesas
SH-Mobile pin controller code from arch/arm/mach-shmobile over to the
generic pinctrl subsystem, changing it over to the common interfaces in
the process.
Based on agreement between Olof, Paul Mundt, Linus Walleij and Simon,
we're merging this large branch of pinctrl conversion through arm-soc,
even though it contains the corresponding conversions for arch/sh. Main
reason for this is tight dependencies (that will now mostly be broken)
between the arch/sh and mach-shmobile implementations.
There will be more of this in 3.10 to do device-tree bindings, but this
is the initial conversion.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=U+ce
-----END PGP SIGNATURE-----
Merge tag 'sh-pinmux' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sh-mobile pinctrl conversion from Arnd Bergmann:
"This is another cleanup series, containing the move of the Renesas
SH-Mobile pin controller code from arch/arm/mach-shmobile over to the
generic pinctrl subsystem, changing it over to the common interfaces
in the process.
Based on agreement between Olof, Paul Mundt, Linus Walleij and Simon,
we're merging this large branch of pinctrl conversion through arm-soc,
even though it contains the corresponding conversions for arch/sh.
Main reason for this is tight dependencies (that will now mostly be
broken) between the arch/sh and mach-shmobile implementations.
There will be more of this in 3.10 to do device-tree bindings, but
this is the initial conversion."
* tag 'sh-pinmux' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (81 commits)
sh-pfc: sh_pfc_probe() sizeof() fix
sh-pfc: Move sh_pfc.h from include/linux/ to driver directory
sh-pfc: Remove pinmux_info definition
sh: Remove unused sh_pfc_register_info() function
sh: shx3: pinmux: Use driver-provided pinmux info
sh: sh7786: pinmux: Use driver-provided pinmux info
sh: sh7785: pinmux: Use driver-provided pinmux info
sh: sh7757: pinmux: Use driver-provided pinmux info
sh: sh7734: pinmux: Use driver-provided pinmux info
sh: sh7724: pinmux: Use driver-provided pinmux info
sh: sh7723: pinmux: Use driver-provided pinmux info
sh: sh7722: pinmux: Use driver-provided pinmux info
sh: sh7720: pinmux: Use driver-provided pinmux info
sh: sh7269: pinmux: Use driver-provided pinmux info
sh: sh7264: pinmux: Use driver-provided pinmux info
sh: sh7203: pinmux: Use driver-provided pinmux info
ARM: shmobile: sh73a0: Use driver-provided pinmux info
ARM: shmobile: sh7372: Use driver-provided pinmux info
ARM: shmobile: r8a7779: Use driver-provided pinmux info
ARM: shmobile: r8a7740: Use driver-provided pinmux info
...
A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even specify
the driver they use, it can all get configured from the device tree
as we do for normal device drivers. The clocksource changes basically
touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose
their headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DvgJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
Bug fixes that did not make it into v3.8, mostly because they were not
considered important enough, and in some cases because bugs only show
up in combination with other patches destined for 3.9.
This includes a few larger patches for GPIO on the Marvell PXA platform
and a lot of Samsung specific bug fixes, as well as a series from Arnd
to fix older build warnings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BbV4
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM SoC bug fixes from Arnd Bergmann:
"Bug fixes that did not make it into v3.8, mostly because they were not
considered important enough, and in some cases because bugs only show
up in combination with other patches destined for 3.9. This includes
a few larger patches for GPIO on the Marvell PXA platform and a lot of
Samsung specific bug fixes, as well as a series from Arnd to fix older
build warnings."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: SPEAr13xx: Enable CONFIG_ARCH_HAS_CPUFREQ
ARM: imx: MACH_MX31ADS_WM1133_EV1 needs REGULATOR_WM8350
scripts/sortextable: silence script output
ARM: s3c: i2c: add platform_device forward declaration
ARM: mvebu: allow selecting mvebu without Armada XP
ARM: pick Versatile by default for !MMU
ARM: integrator: fix build with INTEGRATOR_AP off
ARM: integrator/versatile: fix NOMMU warnings
ARM: sa1100: don't warn about mach/ide.h
ARM: shmobile: fix defconfig warning on CONFIG_USB
ARM: w90x900: fix legacy assembly syntax
ARM: samsung: fix assembly syntax for new gas
ARM: disable virt_to_bus/virt_to_bus almost everywhere
ARM: dts: Correct pin configuration of SD 4 for exynos4x12-pinctrl
ARM: SAMSUNG: Silence empty switch warning in fimc-core.h
ARM: SAMSUNG: Silence empty switch warning in sdhci.h
ARM: msm: proc_comm_boot_wait should not be __init
arm: vt8500: Update MAINTAINERS entry for arch-vt8500
ARM: integrator: ensure ap_syscon_base is initialised when !CONFIG_MMU
ARM: S5PV210: Fix early uart output in fifo mode
...
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
Here's the big USB merge for 3.9-rc1
Nothing major, lots of gadget fixes, and of course, xhci stuff.
All of this has been in linux-next for a while, with the exception of
the last 3 patches, which were reverts of patches in the tree that
caused problems, they went in yesterday.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZ/kACgkQMUfUDdst+ylEhwCgyM0JEOgLuW7M8D+oNcitZn51
g7oAniD0IkLG8RCB8plLj+82AvthalCo
=bHSs
-----END PGP SIGNATURE-----
Merge tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB merge for 3.9-rc1
Nothing major, lots of gadget fixes, and of course, xhci stuff.
All of this has been in linux-next for a while, with the exception of
the last 3 patches, which were reverts of patches in the tree that
caused problems, they went in yesterday."
* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (190 commits)
Revert "USB: EHCI: make ehci-vt8500 a separate driver"
Revert "USB: EHCI: make ehci-orion a separate driver"
Revert "USB: update host controller Kconfig entries"
USB: update host controller Kconfig entries
USB: EHCI: make ehci-orion a separate driver
USB: EHCI: make ehci-vt8500 a separate driver
USB: usb-storage: unusual_devs update for Super TOP SATA bridge
USB: ehci-omap: Fix autoloading of module
USB: ehci-omap: Don't free gpios that we didn't request
USB: option: add Huawei "ACM" devices using protocol = vendor
USB: serial: fix null-pointer dereferences on disconnect
USB: option: add Yota / Megafon M100-1 4g modem
drivers/usb: add missing GENERIC_HARDIRQS dependencies
USB: storage: properly handle the endian issues of idProduct
testusb: remove all mentions of 'usbfs'
usb: gadget: imx_udc: make it depend on BROKEN
usb: omap_control_usb: fix compile warning
ARM: OMAP: USB: Add phy binding information
ARM: OMAP2: MUSB: Specify omap4 has mailbox
ARM: OMAP: devices: create device for usb part of control module
...
Here's the big staging tree merge for 3.9-rc1
Lots of cleanups and updates for drivers all through the staging tree.
We are pretty much "code neutral" here, adding just about as many lines
as we removed.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEUEABECAAYFAlEmW7QACgkQMUfUDdst+ymlIACXT5mv8Y5A/KJa+QLTNNsofI8u
aACgq9hNZxJzX6VQMLXUV8+2SILOqYo=
=5wIj
-----END PGP SIGNATURE-----
Merge tag 'staging-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree update from Greg Kroah-Hartman:
"Here's the big staging tree merge for 3.9-rc1
Lots of cleanups and updates for drivers all through the staging tree.
We are pretty much "code neutral" here, adding just about as many
lines as we removed.
All of these have been in linux-next for a while."
* tag 'staging-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (804 commits)
staging: comedi: vmk80xx: wait for URBs to complete
staging: comedi: drivers: addi-data: hwdrv_apci3200.c: Add a missing semicolon
staging: et131x: Update TODO list
staging: et131x: Remove assignment of skb->dev
staging: wlan-ng: hfa384x.h: fix for error reported by smatch
staging/zache checkpatch ERROR: spaces prohibited around that
staging/ozwpan: Mark read only parameters and structs as const
staging/ozwpan: Remove empty and unused function oz_cdev_heartbeat
staging/ozwpan: Mark local functions as static (fix sparse warnings)
staging/ozwpan: Add missing header includes
staging/usbip: Mark local functions as static (fix sparse warnings)
staging/xgifb: Remove duplicated code in loops.
staging/xgifb: Consolidate return paths
staging/xgifb: Remove code without effect
staging/xgifb: Remove unnecessary casts
staging/xgifb: Consolidate if/else if with identical code branches
staging: vt6656: replaced custom TRUE definition with true
staging: vt6656: replaced custom FALSE definition with false
staging: vt6656: replace custom BOOL definition with bool
staging/rtl8187se: Mark functions as static to silence sparse
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
The biggest change in this update is the unification of HD-audio codec
parsers. Now the HD-audio codec is parsed in a generic parser code
which is invoked by each HD-audio codec driver. Some background
information is found in David Henningsson's blog entry:
http://voices.canonical.com/david.henningsson/2013/01/18/upcoming-changes-to-the-intel-hda-drivers/
Other than that, some random updates/fixes like USB-audio and a bunch
of small AoC updates as usual.
Highlights:
- Unification of HD-audio parser code (aka generic parser)
- Support of new Intel HD-audio controller, new IDT codecs
- Fixes for HD-audio HDMI audio hotplug
- Haswell HDMI audio fixup
- Support of Creative CA0132 DSP code
- A few fixes of HDSP driver
- USB-audio fix for Roland A-PRO, M-Audio FT C600
- Support PM for aloop driver (and fixes Oops)
- Compress API updates for gapless playback support
For ASoC part:
- Support for a wider range of hardware in the compressed stream code
- The ability to mute capture streams as well as playback streams while
inactive
- DT support for AK4642, FSI, Samsung I2S and WM8962
- AC'97 support for Tegra
- New driver for max98090, replacing the stub which was there
- A new driver from Dialog
Note that due to dependencies, DTification of DMA support for Samsung
platforms (used only by the and I2S driver and SPI) is merged here as
well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=nIPc
-----END PGP SIGNATURE-----
Merge tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The biggest change in this update is the unification of HD-audio codec
parsers. Now the HD-audio codec is parsed in a generic parser code
which is invoked by each HD-audio codec driver.
Some background information is found in David Henningsson's blog
entry:
http://voices.canonical.com/david.henningsson/2013/01/18/upcoming-changes-to-the-intel-hda-drivers/
Other than that, some random updates/fixes like USB-audio and a bunch
of small AoC updates as usual.
Highlights:
- Unification of HD-audio parser code (aka generic parser)
- Support of new Intel HD-audio controller, new IDT codecs
- Fixes for HD-audio HDMI audio hotplug
- Haswell HDMI audio fixup
- Support of Creative CA0132 DSP code
- A few fixes of HDSP driver
- USB-audio fix for Roland A-PRO, M-Audio FT C600
- Support PM for aloop driver (and fixes Oops)
- Compress API updates for gapless playback support
For ASoC part:
- Support for a wider range of hardware in the compressed stream code
- The ability to mute capture streams as well as playback streams
while inactive
- DT support for AK4642, FSI, Samsung I2S and WM8962
- AC'97 support for Tegra
- New driver for max98090, replacing the stub which was there
- A new driver from Dialog
Note that due to dependencies, DTification of DMA support for Samsung
platforms (used only by the and I2S driver and SPI) is merged here as
well."
Fix up trivial conflict in drivers/spi/spi-s3c64xx.c due to removed code
being changed.
* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (453 commits)
ALSA: usb: Fix Processing Unit Descriptor parsers
ALSA: hda - hdmi: Notify userspace when ELD control changes
ALSA: hda - hdmi: Protect ELD buffer
ALSA: hda - hdmi: Refactor hdmi_eld into parsed_hdmi_eld
ALSA: hda - hdmi: Do not expose eld data when eld is invalid
ALSA: hda - hdmi: ELD shouldn't be valid after unplug
ALSA: hda - Fix the silent speaker output on Fujitsu S7020 laptop
ALSA: hda - add quirks for mute LED on two HP machines
ALSA: usb/quirks, fix out-of-bounds access
ASoC: codecs: Add da7213 codec
ALSA: au88x0 - Define channel map for au88x0
ALSA: compress: add support for gapless playback
ALSA: hda - Remove speaker clicks on CX20549
ALSA: hda - Disable runtime PM for Intel 5 Series/3400
ALSA: hda - Increase badness for missing multi-io
ASoC: arizona: Automatically manage input mutes
ALSA: hda - Fix broken workaround for HDMI/SPDIF conflicts
ALSA: hda/ca0132 - Add missing \n to debug prints
ALSA: hda/ca0132 - Fix type of INVALID_CHIP_ADDRESS
ALSA: hda - update documentation for no-primary-hp fixup
...
Following commit 26ffd0d4 (ARM: mm: introduce present, faulting entries
for PAGE_NONE), if a page has been mapped as PROT_NONE, the L_PTE_VALID
bit is cleared by the set_pte_ext() code. With LPAE the software and
hardware pte share the same location and subsequent modifications of pte
range (change_protection()) will leave the L_PTE_VALID bit cleared.
This patch adds the L_PTE_VALID bit to the newprot mask in pte_modify().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Subash Patel <subash.rp@samsung.com>
Tested-by: Subash Patel <subash.rp@samsung.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 3.8.x
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When udelay() is implemented using an architected timer, it is wrong
to scale loops_per_jiffy when changing the CPU clock frequency since
the timer clock remains constant.
The lpj should probably become an implementation detail relevant to
the CPU loop based delay routine only and more confined to it. In the
mean time this is the minimal fix needed to have expected delays with
the timer based implementation when cpufreq is also in use.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull networking update from David Miller:
1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
timestamp offset. From Andrey Vagin.
2) VMWARE VM VSOCK layer, from Andy King.
3) Much improved support for virtual functions and SR-IOV in bnx2x,
from Ariel ELior.
4) All protocols on ipv4 and ipv6 are now network namespace aware, and
all the compatability checks for initial-namespace-only protocols is
removed. Thanks to Tom Parkin for helping deal with the last major
holdout, L2TP.
5) IPV6 support in netpoll and network namespace support in pktgen,
from Cong Wang.
6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
Protocol (MVRP) support, from David Ward.
7) Compute packet lengths more accurately in the packet scheduler, from
Eric Dumazet.
8) Use per-task page fragment allocator in skb_append_datato_frags(),
also from Eric Dumazet.
9) Add support for connection tracking labels in netfilter, from
Florian Westphal.
10) Fix default multicast group joining on ipv6, and add anti-spoofing
checks to 6to4 and 6rd. From Hannes Frederic Sowa.
11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
times, rearrange inet frag datastructures for better cacheline
locality, and move more operations outside of locking. From Jesper
Dangaard Brouer.
12) Instead of strict master <--> slave relationships, allow arbitrary
scenerios with "upper device lists". From Jiri Pirko.
13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
Pirko.
14) Add a BPF filter netfilter match target, from Willem de Bruijn.
15) Orphan and delete a bunch of pre-historic networking drivers from
Paul Gortmaker.
16) Add TSO support for GRE tunnels, from Pravin B SHelar. Although
this still needs some minor bug fixing before it's %100 correct in
all cases.
17) Handle unresolved IPSEC states like ARP, with a resolution packet
queue. From Steffen Klassert.
18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
Hemminger. This was long overdue.
19) Support SO_REUSEPORT, from Tom Herbert.
20) Allow locking a socket BPF filter, so that it cannot change after a
process drops capabilities.
21) Add VLAN filtering to bridge, from Vlad Yasevich.
22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
the ipv6 routes, from YOSHIFUJI Hideaki.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
ipv6: fix race condition regarding dst->expires and dst->from.
net: fix a wrong assignment in skb_split()
ip_gre: remove an extra dst_release()
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
atl1c: restore buffer state
net: fix a build failure when !CONFIG_PROC_FS
net: ipv4: fix waring -Wunused-variable
net: proc: fix build failed when procfs is not configured
Revert "xen: netback: remove redundant xenvif_put"
net: move procfs code to net/core/net-procfs.c
qmi_wwan, cdc-ether: add ADU960S
bonding: set sysfs device_type to 'bond'
bonding: fix bond_release_all inconsistencies
b44: use netdev_alloc_skb_ip_align()
xen: netback: remove redundant xenvif_put
net: fec: Do a sanity check on the gpio number
ip_gre: propogate target device GSO capability to the tunnel device
ip_gre: allow CSUM capable devices to handle packets
bonding: Fix initialize after use for 3ad machine state spinlock
bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
...
Pull sparc updates from David Miller:
"Mostly more sparc64 THP bug fixes, and a refactoring of SMP bootup on
sparc32 from Sam Ravnborg."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc32: refactor smp boot
sparc64: Fix huge PMD to PTE translation for sun4u in TLB miss handler.
sparc64: Fix tsb_grow() in atomic context.
sparc64: Handle hugepage TSB being NULL.
sparc64: Fix gfp_flags setting in tsb_grow().
interface).
- Simple earlyprintk support.
- Platform devices populated by default from the DT (SoC-agnostic).
- CONTEXTIDR support (used by external trace tools).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=2prj
-----END PGP SIGNATURE-----
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 patches from Catalin Marinas:
- SMP support for the PSCI booting protocol (power state coordination
interface).
- Simple earlyprintk support.
- Platform devices populated by default from the DT (SoC-agnostic).
- CONTEXTIDR support (used by external trace tools).
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: mm: update CONTEXTIDR register to contain PID of current process
arm64: atomics: fix grossly inconsistent asm constraints for exclusives
arm64: compat: use compat_uptr_t type for compat_ucontext.uc_link
arm64: Select ARCH_WANT_FRAME_POINTERS
arm64: Add kvm_para.h and xor.h generic headers
arm64: SMP: enable PSCI boot method
arm64: psci: add support for PSCI invocations from the kernel
arm64: SMP: rework the SMP code to be enabling method agnostic
arm64: perf: add guest vs host discrimination
arm64: add COMPAT_PSR_*_BIT flags
arm64: Add simple earlyprintk support
arm64: Populate the platform devices
Pull ARM updates (part two) from Russell King:
- breakpoint and perf updates from Will Deacon.
- hypervisor boot mode updates from Will.
- support for Power State Coordination Interface via the Hypervisor
- core ARM support for KVM
* 'for-linus-2' of git://git.linaro.org/people/rmk/linux-arm: (32 commits)
KVM: ARM: Add maintainer entry for KVM/ARM
KVM: ARM: Power State Coordination Interface implementation
KVM: ARM: Handle I/O aborts
KVM: ARM: Handle guest faults in KVM
KVM: ARM: VFP userspace interface
KVM: ARM: Demux CCSIDR in the userspace API
KVM: ARM: User space API for getting/setting co-proc registers
KVM: ARM: Emulation framework and CP15 emulation
KVM: ARM: World-switch implementation
KVM: ARM: Inject IRQs and FIQs from userspace
KVM: ARM: Memory virtualization setup
KVM: ARM: Hypervisor initialization
KVM: ARM: Initial skeleton to compile KVM support
ARM: Section based HYP idmap
ARM: Add page table and page defines needed by KVM
ARM: perf: simplify __hw_perf_event_init err handling
ARM: perf: remove unnecessary checks for idx < 0
ARM: perf: handle armpmu_register failing
ARM: perf: don't pretend to support counting of L1I writes
ARM: perf: remove redundant NULL check on cpu_pmu
...
Pull ARM updates (part one) from Russell King:
- MMC patches from Ulf Hansson and Pawel Moll. These add support for
DDR mode and the latest variant found on ARM Versatile Express, as
well as a number of cleanups.
- A fix for to improve the behaviour of ARMs sched_clock()
- Changes to the ARM ioremap() code. I'm not convinced with the
primary arguments for this, but it's been around for a while, and
people seem happy with it - and the "other" justification for this is
at
http://lkml.org/lkml/2012/12/6/184
- Add SCHED_HRTICK to ARMs Kconfig
- Making the ARM SHA/AES code Thumb-2 compatible
- A collection of other small updates.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (26 commits)
ARM: add SCHED_HRTICK config option
ARM: 7650/1: mm: replace direct access to mm->context.id with new macro
ARM: 7649/1: mm: mm->context.id fix for big-endian
ARM: 7648/1: pci: Allow passing per-controller private data
ARM: 7647/1: pci: Keep pci_common_init() around after init
ARM: fix warnings introduced by previous patch
ARM: 7646/1: mm: use static_vm for managing static mapped areas
ARM: 7645/1: ioremap: introduce an infrastructure for static mapped area
ARM: 7644/1: vmregion: remove vmregion code entirely
MAINTAINERS: Re-assert MMCI driver maintainer status
MAINTAINERS: add additional file for MMCI driver
MAINTAINERS: add maintainer entry for AMBA serial drivers
ARM: 7637/1: memory: use SZ_ constants for defining the virtual memory layout
ARM: 7643/1: sched: correct update_sched_clock()
ARM: 7635/1: versatile: fix the PCI IRQ regression
ARM: 7639/1: cache-l2x0: add missed dummy outer_resume entry
ARM: 7630/1: mmc: mmci: Fixup and cleanup code for DMA handling
ARM: 7632/1: spinlock: avoid exclusive accesses on unlock() path
ARM: 7631/1: mmc: mmci: Add new VE MMCI variant
ARM: 7623/1: mmc: mmci: Fixup clock gating when freq is 0 for ST-variants
...
James Hogan