Add device state check before executing command. Without the check the
command can be issued while device is in halt state and causes the driver to
block while waiting for the completion of the command.
Reported-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Fixes: 0d5c10b4c8 ("dmaengine: idxd: add work queue drain support")
Link: https://lore.kernel.org/r/161219313921.2976211.12222625226450097465.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to allow configuration of Intel Analytics Accelerator (IAX) in
addition to the Intel Data Streaming Accelerator (DSA). The IAX hardware
has the same configuration interface as DSA. The main difference
is the type of operations it performs. We can support the DSA and
IAX devices on the same driver with some tweaks.
IAX has a 64B completion record that needs to be 64B aligned, as opposed to
a 32B completion record that is 32B aligned for DSA. IAX also does not
support token management.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/160564555488.1834439.4261958859935360473.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add code to "complete" a descriptor when the descriptor or its completion
address hit a fault error when SVA mode is being used. This error can be
triggered due to bad programming by the user. A lock is introduced in order
to protect the descriptor completion lists since the fault handler will run
from the system work queue after being scheduled in the interrupt handler.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/160382008092.3911367.12766483427643278985.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add shared workqueue support that includes the support of Shared Virtual
memory (SVM) or in similar terms On Demand Paging (ODP). The shared
workqueue uses the enqcmds command in kernel and will respond with retry if
the workqueue is full. Shared workqueue only works when there is PASID
support from the IOMMU.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/160382007499.3911367.26043087963708134.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Export admin command status to sysfs attribute in order to allow user to
retrieve configuration error. Allows user tooling to retrieve the command
error and provide more user friendly error messages.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/159865278770.29455.8026892329182750127.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add sysfs attribute max_batch_size to wq in order to allow the max batch
size configured on a per wq basis. Add support code to configure
the valid user input on wq enable. This is a performance tuning
parameter.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/159865273617.29141.4383066301730821749.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add sysfs attribute max_xfer_size to wq in order to allow the max xfer
size configured on a per wq basis. Add support code to configure
the valid user input on wq enable. This is a performance tuning
parameter.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/159865265404.29141.3049399618578194052.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Switch driver to use MSIX mask and unmask instead of the ignore bit.
When ignore bit is cleared, we must issue an MMIO read to ensure writes
have all arrived and check and process any additional completions. The
ignore bit does not queue up any pending MSIX interrupts. The mask bit
however does. Use API call from interrupt subsystem to mask MSIX
interrupt since the hardware does not have convenient mask bit register.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/159319517621.70410.11816465052708900506.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add wq drain support. When a wq is being released, it needs to wait for
all in-flight operation to complete. A device control function
idxd_wq_drain() has been added to facilitate this. A wq drain call
is added to the char dev on release to make sure all user operations are
complete. A wq drain is also added before the wq is being disabled.
A drain command can take an unpredictable period of time. Interrupt support
for device commands is added to allow waiting on the command to
finish. If a previous command is in progress, the new submitter can block
until the current command is finished before proceeding. The interrupt
based submission will submit the command and then wait until a command
completion interrupt happens to complete. All commands are moved to the
interrupt based command submission except for the device reset during
probe, which will be polled.
Fixes: 42d279f913 ("dmaengine: idxd: add char driver to expose submission portal to userland")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/159319502515.69593.13451647706946040301.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After disabling a device, we should clean up the internal state for
the wqs and zero out the configuration registers. Without doing so can cause
issues when the user reprogram the wqs.
Fixes: c52ca47823 ("dmaengine: idxd: add configuration component of driver")
Reported-by: Yixin Zhang <yixin.zhang@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Yixin Zhang <yixin.zhang@intel.com>
Link: https://lore.kernel.org/r/159311264246.1198.11955791213681679428.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Create a char device region that will allow acquisition of user portals in
order to allow applications to submit DMA operations. A char device will be
created per work queue that gets exposed. The workqueue type "user"
is used to mark a work queue for user char device. For example if the
workqueue 0 of DSA device 0 is marked for char device, then a device node
of /dev/dsa/wq0.0 will be created.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/157965026985.73301.976523230037106742.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add plumbing for dmaengine subsystem connection. The driver register a DMA
device per DSA device. The channels are dynamically registered when a
workqueue is configured to be "kernel:dmanegine" type.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/157965026376.73301.13867988830650740445.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The device is left unconfigured when the driver is loaded. Various
components are configured via the driver sysfs attributes. Once
configuration is done, the device can be enabled by writing the device name
to the bind attribute of the device driver sysfs. Disabling can be done
similarly. Also the individual work queues can also be enabled and disabled
through the bind/unbind attributes. A constructed hierarchy is created
through the struct device framework in order to provide appropriate
configuration points and device state and status. This hierarchy is
presented off the virtual DSA bus.
i.e. /sys/bus/dsa/...
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/157965024585.73301.6431413676230150589.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The idxd driver introduces the Intel Data Stream Accelerator [1] that will
be available on future Intel Xeon CPUs. One of the kernel access
point for the driver is through the dmaengine subsystem. It will initially
provide the DMA copy service to the kernel.
Some of the main functionality introduced with this accelerator
are: shared virtual memory (SVM) support, and descriptor submission using
Intel CPU instructions movdir64b and enqcmds. There will be additional
accelerator devices that share the same driver with variations to
capabilities.
This commit introduces the probe and initialization component of the
driver.
[1]: https://software.intel.com/en-us/download/intel-data-streaming-accelerator-preliminary-architecture-specification
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/157965023991.73301.6186843973135311580.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Dave Jiang