Since 412445ac ("dm: introduce a new DM_MAPIO_KILL return value"), the
clone_and_map_rq methods must not return errno values, so fix it up
to properly return DM_MAPIO_KILL, instead of the -EIO value that snuck
in due to a conflict between two patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Instead just turn the macro into a helper for the warning message.
This removes an unnecessary assignment and will allow the next commit to
fix a place where -EIO is the wrong return value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We don't want to bug when receiving a DM_MAPIO_KILL value..
Fixes: 412445ac ("dm: introduce a new DM_MAPIO_KILL return value")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When decrementing the reference count for a block, the free count wasn't
being updated if the reference count went to zero.
Cc: stable@vger.kernel.org
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
These calls were the wrong way round in __write_initial_superblock.
Cc: stable@vger.kernel.org
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If there are no clean blocks to be demoted the writeback will be
triggered at that point. Preemptively writing back can hurt high IO
load scenarios.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Drop the MODERATE state since it wasn't buying us much.
Also, in check_migrations(), prepare for the next commit ("dm cache
policy smq: don't do any writebacks unless IDLE") by deferring to the
policy to make the final decision on whether writebacks can be
serviced.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
IO tracking used to throttle writebacks when the origin device is busy.
Even if all the IO is going to the fast device, writebacks can
significantly degrade performance. So track all IO to gauge whether the
cache is busy or not.
Otherwise, synthetic IO tests (e.g. fio) that might send all IO to the
fast device wouldn't cause writebacks to get throttled.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
It causes a lot of churn if the working set's size is close to the fast
device's size.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This stops entries bouncing in and out of the cache quickly.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If there are no clean entries to demote we really want to writeback
immediately.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Heavy IO load may mean there are very few clean blocks in the cache, and
we risk demoting entries that get hit a lot.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Some bios have no payload (eg, a FLUSH), don't reset the idle_time when
these come in.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If an array consists of two drives and the first drive has the bad
block, the read request to the region overlapping the bad block chooses
the same disk (with bad block) as device to read from over and over and
the request gets stuck. If the first disk only partially overlaps with
bad block, it becomes a candidate ("best disk") for shorter range of
sectors. The second disk is capable of reading the entire requested
range and it is updated accordingly, however it is not recorded as a
best device for the request. In the end the request is sent to the first
disk to read entire range of sectors. It fails and is re-tried in a
moment but with the same outcome.
Actually it is quite likely scenario but it had little exposure in my
test until commit 715d40b93b10 ("md/raid1: add failfast handling for
reads.") removed preference for idle disk. Such scenario had been
passing as second disk was always chosen when idle.
Reset a candidate ("best disk") to read from if disk can read entire
range. Do it only if other disk has already been chosen as a candidate
for a smaller range. The head position / disk type logic will select
the best disk to read from - it is fine as disk with bad block won't be
considered for it.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Currently, sync of raid456 array cannot make progress when hitting
data in writeback r5cache.
This patch fixes this issue by flushing cached data of the stripe
before processing the sync request. This is achived by:
1. In handle_stripe(), do not set STRIPE_SYNCING if the stripe is
in write back cache;
2. In r5c_try_caching_write(), handle the stripe in sync with write
through;
3. In do_release_stripe(), make stripe in sync write out and send
it to the state machine.
Shaohua: explictly set STRIPE_HANDLE after write out completed
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
For the raid456 with writeback cache, when journal device failed during
normal operation, it is still possible to persist all data, as all
pending data is still in stripe cache. However, it is necessary to handle
journal failure gracefully.
During journal failures, the following logic handles the graceful shutdown
of journal:
1. raid5_error() marks the device as Faulty and schedules async work
log->disable_writeback_work;
2. In disable_writeback_work (r5c_disable_writeback_async), the mddev is
suspended, set to write through, and then resumed. mddev_suspend()
flushes all cached stripes;
3. All cached stripes need to be flushed carefully to the RAID array.
This patch fixes issues within the process above:
1. In r5c_update_on_rdev_error() schedule disable_writeback_work for
journal failures;
2. In r5c_disable_writeback_async(), wait for MD_SB_CHANGE_PENDING,
since raid5_error() updates superblock.
3. In handle_stripe(), allow stripes with data in journal (s.injournal > 0)
to make progress during log_failed;
4. In delay_towrite(), if log failed only process data in the cache (skip
new writes in dev->towrite);
5. In __get_priority_stripe(), process loprio_list during journal device
failures.
6. In raid5_remove_disk(), wait for all cached stripes are flushed before
calling log_exit().
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If we add bios to block plugging list, locking is unnecessry, since the block
unplug is guaranteed not to run at that time.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
In r5l_do_submit_io(), it is necessary to check io->split_bio before
submit io->current_bio. This is because, endio of current_bio may
free the whole IO unit, and thus change io->split_bio.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
There are complaints that raid0 discard handling is slow. Currently we
divide discard request into chunks and dispatch to underlayer disks. The
block layer will do merge to form big requests. This causes a lot of
request split/merge and uses significant CPU time.
A simple idea is to calculate the range for each raid disk for an IO
request and send a discard request to raid disks, which will avoid the
split/merge completely. Previously Coly tried the approach, but the
implementation was too complex because of raid0 zones. This patch always
split bio in zone boundary and handle bio within one zone. It simplifies
the implementation a lot.
Reviewed-by: NeilBrown <neilb@suse.com>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
__vmalloc* allows users to provide gfp flags for the underlying
allocation. This API is quite popular
$ git grep "=[[:space:]]__vmalloc\|return[[:space:]]*__vmalloc" | wc -l
77
The only problem is that many people are not aware that they really want
to give __GFP_HIGHMEM along with other flags because there is really no
reason to consume precious lowmemory on CONFIG_HIGHMEM systems for pages
which are mapped to the kernel vmalloc space. About half of users don't
use this flag, though. This signals that we make the API unnecessarily
too complex.
This patch simply uses __GFP_HIGHMEM implicitly when allocating pages to
be mapped to the vmalloc space. Current users which add __GFP_HIGHMEM
are simplified and drop the flag.
Link: http://lkml.kernel.org/r/20170307141020.29107-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Cristopher Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bcache_device_init uses kmalloc for small requests and vmalloc for those
which are larger than 64 pages. This alone is a strange criterion.
Moreover kmalloc can fallback to vmalloc on the failure. Let's simply
use kvmalloc instead as it knows how to handle the fallback properly
Link: http://lkml.kernel.org/r/20170306103327.2766-5-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
copy_params uses kmalloc with vmalloc fallback. We already have a
helper for that - kvmalloc. This caller requires GFP_NOIO semantic so
it hasn't been converted with many others by previous patches. All we
need to achieve this semantic is to use the scope
memalloc_noio_{save,restore} around kvmalloc.
Link: http://lkml.kernel.org/r/20170306103327.2766-4-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are many code paths opencoding kvmalloc. Let's use the helper
instead. The main difference to kvmalloc is that those users are
usually not considering all the aspects of the memory allocator. E.g.
allocation requests <= 32kB (with 4kB pages) are basically never failing
and invoke OOM killer to satisfy the allocation. This sounds too
disruptive for something that has a reasonable fallback - the vmalloc.
On the other hand those requests might fallback to vmalloc even when the
memory allocator would succeed after several more reclaim/compaction
attempts previously. There is no guarantee something like that happens
though.
This patch converts many of those places to kv[mz]alloc* helpers because
they are more conservative.
Link: http://lkml.kernel.org/r/20170306103327.2766-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> # Xen bits
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Andreas Dilger <andreas.dilger@intel.com> # Lustre
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> # KVM/s390
Acked-by: Dan Williams <dan.j.williams@intel.com> # nvdim
Acked-by: David Sterba <dsterba@suse.com> # btrfs
Acked-by: Ilya Dryomov <idryomov@gmail.com> # Ceph
Acked-by: Tariq Toukan <tariqt@mellanox.com> # mlx4
Acked-by: Leon Romanovsky <leonro@mellanox.com> # mlx5
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Yishai Hadas <yishaih@mellanox.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: "Yan, Zheng" <zyan@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "kvmalloc", v5.
There are many open coded kmalloc with vmalloc fallback instances in the
tree. Most of them are not careful enough or simply do not care about
the underlying semantic of the kmalloc/page allocator which means that
a) some vmalloc fallbacks are basically unreachable because the kmalloc
part will keep retrying until it succeeds b) the page allocator can
invoke a really disruptive steps like the OOM killer to move forward
which doesn't sound appropriate when we consider that the vmalloc
fallback is available.
As it can be seen implementing kvmalloc requires quite an intimate
knowledge if the page allocator and the memory reclaim internals which
strongly suggests that a helper should be implemented in the memory
subsystem proper.
Most callers, I could find, have been converted to use the helper
instead. This is patch 6. There are some more relying on __GFP_REPEAT
in the networking stack which I have converted as well and Eric Dumazet
was not opposed [2] to convert them as well.
[1] http://lkml.kernel.org/r/20170130094940.13546-1-mhocko@kernel.org
[2] http://lkml.kernel.org/r/1485273626.16328.301.camel@edumazet-glaptop3.roam.corp.google.com
This patch (of 9):
Using kmalloc with the vmalloc fallback for larger allocations is a
common pattern in the kernel code. Yet we do not have any common helper
for that and so users have invented their own helpers. Some of them are
really creative when doing so. Let's just add kv[mz]alloc and make sure
it is implemented properly. This implementation makes sure to not make
a large memory pressure for > PAGE_SZE requests (__GFP_NORETRY) and also
to not warn about allocation failures. This also rules out the OOM
killer as the vmalloc is a more approapriate fallback than a disruptive
user visible action.
This patch also changes some existing users and removes helpers which
are specific for them. In some cases this is not possible (e.g.
ext4_kvmalloc, libcfs_kvzalloc) because those seems to be broken and
require GFP_NO{FS,IO} context which is not vmalloc compatible in general
(note that the page table allocation is GFP_KERNEL). Those need to be
fixed separately.
While we are at it, document that __vmalloc{_node} about unsupported gfp
mask because there seems to be a lot of confusion out there.
kvmalloc_node will warn about GFP_KERNEL incompatible (which are not
superset) flags to catch new abusers. Existing ones would have to die
slowly.
[sfr@canb.auug.org.au: f2fs fixup]
Link: http://lkml.kernel.org/r/20170320163735.332e64b7@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170306103032.2540-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Andreas Dilger <adilger@dilger.ca> [ext4 part]
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This essentially reverts commit b5470dc5fc ("md: resolve external
metadata handling deadlock in md_allow_write") with some adjustments.
Since commit 6791875e2e ("md: make reconfig_mutex optional for writes
to md sysfs files.") changing array_state to 'active' does not use
mddev_lock() and will not cause a deadlock with md_allow_write(). This
revert simplifies userspace tools that write to sysfs attributes like
"stripe_cache_size" or "consistency_policy" because it removes the need
for special handling for external metadata arrays, checking for EAGAIN
and retrying the write.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull block fixes and updates from Jens Axboe:
"Some fixes and followup features/changes that should go in, in this
merge window. This contains:
- Two fixes for lightnvm from Javier, fixing problems in the new code
merge previously in this merge window.
- A fix from Jan for the backing device changes, fixing an issue in
NFS that causes a failure to mount on certain setups.
- A change from Christoph, cleaning up the blk-mq init and exit
request paths.
- Remove elevator_change(), which is now unused. From Bart.
- A fix for queue operation invocation on a dead queue, from Bart.
- A series fixing up mtip32xx for blk-mq scheduling, removing a
bandaid we previously had in place for this. From me.
- A regression fix for this series, fixing a case where we wait on
workqueue flushing from an invalid (non-blocking) context. From me.
- A fix/optimization from Ming, ensuring that we don't both quiesce
and freeze a queue at the same time.
- A fix from Peter on lock ordering for CPU hotplug. Not a real
problem right now, but will be once the CPU hotplug rework goes in.
- A series from Omar, cleaning up out blk-mq debugfs support, and
adding support for exporting info from schedulers in debugfs as
well. This is really useful in debugging stalls or livelocks. From
Omar"
* 'for-linus' of git://git.kernel.dk/linux-block: (28 commits)
mq-deadline: add debugfs attributes
kyber: add debugfs attributes
blk-mq-debugfs: allow schedulers to register debugfs attributes
blk-mq: untangle debugfs and sysfs
blk-mq: move debugfs declarations to a separate header file
blk-mq: Do not invoke queue operations on a dead queue
blk-mq-debugfs: get rid of a bunch of boilerplate
blk-mq-debugfs: rename hw queue directories from <n> to hctx<n>
blk-mq-debugfs: don't open code strstrip()
blk-mq-debugfs: error on long write to queue "state" file
blk-mq-debugfs: clean up flag definitions
blk-mq-debugfs: separate flags with |
nfs: Fix bdi handling for cloned superblocks
block/mq: Cure cpu hotplug lock inversion
lightnvm: fix bad back free on error path
lightnvm: create cmd before allocating request
blk-mq: don't use sync workqueue flushing from drivers
mtip32xx: convert internal commands to regular block infrastructure
mtip32xx: cleanup internal tag assumptions
block: don't call blk_mq_quiesce_queue() after queue is frozen
...
metadata not be in 'fail_io' mode. Otherwise crashes are possible.
- a DM cache fix to address the inability to adapt to continuous IO that
happened to also reflect a changing working set (which required old
blocks be demoted before the new working set could be promoted)
- a DM cache smq policy cleanup that fell out from reviewing the above
- fix the Kconfig help text for CONFIG_DM_INTEGRITY
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZDMmrAAoJEMUj8QotnQNaALIH/3YJj9gZOQly+I6Rk9157nGX
0mjXTd9SV6IT95ulX/DywBt3pbStXim15DYMQG1BxHTqHbrFmTRxR+K/AtbnEXCI
Ww8tJB3Adz4ETVd6IJ2ptCFxBLZwgPDkY6RJlPe8ZG/mBvVLXjKHvNQ5siy7sXvr
gAqn2XrSr5y4ZB06xJXrhfMxW4QHkgOGLcn5TUeXZumU7cAnNBoCWHAqtJtwxxog
Iwaz342PCM81W7rXvnuIJm6PkEDbfNGHbjPZo4vAOHAD/Hok8LZFc89vTRZHO/EB
gElsj9fIMyiLeyhBX/OXxguGBNL8hsyKZ8GdBJ/9Q9FcJvRm/LfkFiRx3agc7Bc=
=mK65
-----END PGP SIGNATURE-----
Merge tag 'for-4.12/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- DM cache metadata fixes to short-circuit operations that require the
metadata not be in 'fail_io' mode. Otherwise crashes are possible.
- a DM cache fix to address the inability to adapt to continuous IO
that happened to also reflect a changing working set (which required
old blocks be demoted before the new working set could be promoted)
- a DM cache smq policy cleanup that fell out from reviewing the above
- fix the Kconfig help text for CONFIG_DM_INTEGRITY
* tag 'for-4.12/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache metadata: fail operations if fail_io mode has been established
dm integrity: improve the Kconfig help text for DM_INTEGRITY
dm cache policy smq: cleanup free_target_met() and clean_target_met()
dm cache policy smq: allow demotions to happen even during continuous IO
* Region media error reporting: A libnvdimm region device is the parent
to one or more namespaces. To date, media errors have been reported via
the "badblocks" attribute attached to pmem block devices for namespaces
in "raw" or "memory" mode. Given that namespaces can be in "device-dax"
or "btt-sector" mode this new interface reports media errors
generically, i.e. independent of namespace modes or state. This
subsequently allows userspace tooling to craft "ACPI 6.1 Section
9.20.7.6 Function Index 4 - Clear Uncorrectable Error" requests and
submit them via the ioctl path for NVDIMM root bus devices.
* Introduce 'struct dax_device' and 'struct dax_operations': Prompted by
a request from Linus and feedback from Christoph this allows for dax
capable drivers to publish their own custom dax operations. This fixes
the broken assumption that all dax operations are related to a
persistent memory device, and makes it easier for other architectures
and platforms to add customized persistent memory support.
* 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger memory
controllers to drain write-pending buffers that would otherwise be
flushed automatically by the platform ADR (asynchronous-DRAM-refresh)
mechanism at a power loss event. Support for "locked" DIMMs is included
to prevent namespaces from surfacing when the namespace label data area
is locked. Finally, fixes for various reported deadlocks and crashes,
also tagged for -stable.
* ACPI / nfit driver updates: General updates of the nfit driver to add
DSM command overrides, ACPI 6.1 health state flags support, DSM payload
debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
commmit 565851c972 "device-dax: fix sysfs attribute deadlock"
Tested-by: Yi Zhang <yizhan@redhat.com>
commit 23f4984483 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>
-----BEGIN PGP SIGNATURE-----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=Ox0s
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The bulk of this has been in multiple -next releases. There were a few
late breaking fixes and small features that got added in the last
couple days, but the whole set has received a build success
notification from the kbuild robot.
Change summary:
- Region media error reporting: A libnvdimm region device is the
parent to one or more namespaces. To date, media errors have been
reported via the "badblocks" attribute attached to pmem block
devices for namespaces in "raw" or "memory" mode. Given that
namespaces can be in "device-dax" or "btt-sector" mode this new
interface reports media errors generically, i.e. independent of
namespace modes or state.
This subsequently allows userspace tooling to craft "ACPI 6.1
Section 9.20.7.6 Function Index 4 - Clear Uncorrectable Error"
requests and submit them via the ioctl path for NVDIMM root bus
devices.
- Introduce 'struct dax_device' and 'struct dax_operations': Prompted
by a request from Linus and feedback from Christoph this allows for
dax capable drivers to publish their own custom dax operations.
This fixes the broken assumption that all dax operations are
related to a persistent memory device, and makes it easier for
other architectures and platforms to add customized persistent
memory support.
- 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger
memory controllers to drain write-pending buffers that would
otherwise be flushed automatically by the platform ADR
(asynchronous-DRAM-refresh) mechanism at a power loss event.
Support for "locked" DIMMs is included to prevent namespaces from
surfacing when the namespace label data area is locked. Finally,
fixes for various reported deadlocks and crashes, also tagged for
-stable.
- ACPI / nfit driver updates: General updates of the nfit driver to
add DSM command overrides, ACPI 6.1 health state flags support, DSM
payload debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
- commmit 565851c972 "device-dax: fix sysfs attribute deadlock":
Tested-by: Yi Zhang <yizhan@redhat.com>
- commit 23f4984483 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>"
* tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (52 commits)
libnvdimm, pfn: fix 'npfns' vs section alignment
libnvdimm: handle locked label storage areas
libnvdimm: convert NDD_ flags to use bitops, introduce NDD_LOCKED
brd: fix uninitialized use of brd->dax_dev
block, dax: use correct format string in bdev_dax_supported
device-dax: fix sysfs attribute deadlock
libnvdimm: restore "libnvdimm: band aid btt vs clear poison locking"
libnvdimm: fix nvdimm_bus_lock() vs device_lock() ordering
libnvdimm: rework region badblocks clearing
acpi, nfit: kill ACPI_NFIT_DEBUG
libnvdimm: fix clear length of nvdimm_forget_poison()
libnvdimm, pmem: fix a NULL pointer BUG in nd_pmem_notify
libnvdimm, region: sysfs trigger for nvdimm_flush()
libnvdimm: fix phys_addr for nvdimm_clear_poison
x86, dax, pmem: remove indirection around memcpy_from_pmem()
block: remove block_device_operations ->direct_access()
block, dax: convert bdev_dax_supported() to dax_direct_access()
filesystem-dax: convert to dax_direct_access()
Revert "block: use DAX for partition table reads"
ext2, ext4, xfs: retrieve dax_device for iomap operations
...
Otherwise it is possible to trigger crashes due to the metadata being
inaccessible yet these methods don't safely account for that possibility
without these checks.
Cc: stable@vger.kernel.org
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
On mainline, there is no functional difference, just less code, and
symmetric lock/unlock paths.
On PREEMPT_RT builds, this fixes the following warning, seen by
Alexander GQ Gerasiov, due to the sleeping nature of spinlocks.
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:993
in_atomic(): 0, irqs_disabled(): 1, pid: 58, name: kworker/u12:1
CPU: 5 PID: 58 Comm: kworker/u12:1 Tainted: G W 4.9.20-rt16-stand6-686 #1
Hardware name: Supermicro SYS-5027R-WRF/X9SRW-F, BIOS 3.2a 10/28/2015
Workqueue: writeback wb_workfn (flush-253:0)
Call Trace:
dump_stack+0x47/0x68
? migrate_enable+0x4a/0xf0
___might_sleep+0x101/0x180
rt_spin_lock+0x17/0x40
add_stripe_bio+0x4e3/0x6c0 [raid456]
? preempt_count_add+0x42/0xb0
raid5_make_request+0x737/0xdd0 [raid456]
Reported-by: Alexander GQ Gerasiov <gq@redlab-i.ru>
Tested-by: Alexander GQ Gerasiov <gq@redlab-i.ru>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Depending on the passed @idle arg, there may be no need to calculate
'nr_free' or 'nr_clean' respectively in free_target_met() and
clean_target_met().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-cache's smq policy tries hard to do it's work during the idle periods
when there is no IO. But if there are no idle periods (eg, a long fio
run) we still need to allow some demotions and promotions to occur.
To achieve this, pass @idle=true to queue_promotion()'s
free_target_met() call so that free_target_met() doesn't short-circuit
the possibility of demotion simply because it isn't an idle period.
Fixes: b29d4986d0 ("dm cache: significant rework to leverage dm-bio-prison-v2")
Reported-by: John Harrigan <jharriga@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
prepare for his block core error code type checking improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZB7R5AAoJEMUj8QotnQNaCFMIAKcE+xFMAf5D6en6Ys5V1Lm6
L6/MdUnbH2j7wZ7CnNgkmDExdJ8dpENyjhy8r4rgXs+BufiVeZ8uGOYsuiXGjOG2
wZ4M4haBbBDsWStyn3C5K3QxpN7ksuxHZC7XR25fDDDIBmJW2/bL7B7kyE9lp6LR
SmP7O0x36twCMrwWrC043NwhCS+lQH+EIqTTX4Q18swtXz/CCAtNDxgGsjxvwfxH
YkCAxzbQlva3nYv29tcKpc89RJK1hWfdkXqb/TW4pPxspexnEjVUFyh019DxEoRr
KPi6hhT6nx2JjMSvJykFasRPAdoyEoUzTNjrGk6WeD6hfzkxsHq/FutbH9BGj8Q=
=h45q
-----END PGP SIGNATURE-----
Merge tag 'for-4.12/dm-post-merge-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull additional device mapper updates from Mike Snitzer:
"Here are some changes from Christoph that needed to be rebased ontop
of changes that were already merged into the device mapper tree. In
addition, these changes depend on the 'for-4.12/block' changes that
you've already merged.
- Cleanups to request-based DM and DM multipath from Christoph that
prepare for his block core error code type checking improvements"
* tag 'for-4.12/dm-post-merge-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: introduce a new DM_MAPIO_KILL return value
dm rq: change ->rq_end_io calling conventions
dm mpath: merge do_end_io into multipath_end_io
whether blocks should migrate to/from the cache. The bio-prison-v2
interface supports this improvement by enabling direct dispatch of
work to workqueues rather than having to delay the actual work
dispatch to the DM cache core. So the dm-cache policies are much more
nimble by being able to drive IO as they see fit. One immediate
benefit from the improved latency is a cache that should be much more
adaptive to changing workloads.
- Add a new DM integrity target that emulates a block device that has
additional per-sector tags that can be used for storing integrity
information.
- Add a new authenticated encryption feature to the DM crypt target that
builds on the capabilities provided by the DM integrity target.
- Add MD interface for switching the raid4/5/6 journal mode and update
the DM raid target to use it to enable aid4/5/6 journal write-back
support.
- Switch the DM verity target over to using the asynchronous hash crypto
API (this helps work better with architectures that have access to
off-CPU algorithm providers, which should reduce CPU utilization).
- Various request-based DM and DM multipath fixes and improvements from
Bart and Christoph.
- A DM thinp target fix for a bio structure leak that occurs for each
discard IFF discard passdown is enabled.
- A fix for a possible deadlock in DM bufio and a fix to re-check the
new buffer allocation watermark in the face of competing admin changes
to the 'max_cache_size_bytes' tunable.
- A couple DM core cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZB6vtAAoJEMUj8QotnQNaoicIALuZTLElgAzxzA28cfk1+1Ea
Gd09CfJ3M6cvk/YGUU7WwiSYIwu16yOJALG4sLcYnEmUCzvKfFPcl/RpeSJHPpYM
0aVXa6NIJw7K2r3C17toiK2DRMHYw6QU843WeWI93vBW13lDJklNJL9fM7GBEOLH
NMSNw2mAq9ajtLlnJhM3ZfhloA7/u/jektvlBO1AA3RQ5Kx1cXVXFPqN7FdRfcqp
4RuEMe9faAadlXLsj3bia5IBmF/W0Qza6JilP+NLKLWB4fm7LZDjN/k+TsHWMa9e
cGR73TgUGLMBJX+sDJy8R3oeBG9JZkFVkD7I30eCjzyhSOs/54XNYQ23EkqHJU0=
=9Ryi
-----END PGP SIGNATURE-----
Merge tag 'for-4.12/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- A major update for DM cache that reduces the latency for deciding
whether blocks should migrate to/from the cache. The bio-prison-v2
interface supports this improvement by enabling direct dispatch of
work to workqueues rather than having to delay the actual work
dispatch to the DM cache core. So the dm-cache policies are much more
nimble by being able to drive IO as they see fit. One immediate
benefit from the improved latency is a cache that should be much more
adaptive to changing workloads.
- Add a new DM integrity target that emulates a block device that has
additional per-sector tags that can be used for storing integrity
information.
- Add a new authenticated encryption feature to the DM crypt target
that builds on the capabilities provided by the DM integrity target.
- Add MD interface for switching the raid4/5/6 journal mode and update
the DM raid target to use it to enable aid4/5/6 journal write-back
support.
- Switch the DM verity target over to using the asynchronous hash
crypto API (this helps work better with architectures that have
access to off-CPU algorithm providers, which should reduce CPU
utilization).
- Various request-based DM and DM multipath fixes and improvements from
Bart and Christoph.
- A DM thinp target fix for a bio structure leak that occurs for each
discard IFF discard passdown is enabled.
- A fix for a possible deadlock in DM bufio and a fix to re-check the
new buffer allocation watermark in the face of competing admin
changes to the 'max_cache_size_bytes' tunable.
- A couple DM core cleanups.
* tag 'for-4.12/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (50 commits)
dm bufio: check new buffer allocation watermark every 30 seconds
dm bufio: avoid a possible ABBA deadlock
dm mpath: make it easier to detect unintended I/O request flushes
dm mpath: cleanup QUEUE_IF_NO_PATH bit manipulation by introducing assign_bit()
dm mpath: micro-optimize the hot path relative to MPATHF_QUEUE_IF_NO_PATH
dm: introduce enum dm_queue_mode to cleanup related code
dm mpath: verify __pg_init_all_paths locking assumptions at runtime
dm: verify suspend_locking assumptions at runtime
dm block manager: remove an unused argument from dm_block_manager_create()
dm rq: check blk_mq_register_dev() return value in dm_mq_init_request_queue()
dm mpath: delay requeuing while path initialization is in progress
dm mpath: avoid that path removal can trigger an infinite loop
dm mpath: split and rename activate_path() to prepare for its expanded use
dm ioctl: prevent stack leak in dm ioctl call
dm integrity: use previously calculated log2 of sectors_per_block
dm integrity: use hex2bin instead of open-coded variant
dm crypt: replace custom implementation of hex2bin()
dm crypt: remove obsolete references to per-CPU state
dm verity: switch to using asynchronous hash crypto API
dm crypt: use WQ_HIGHPRI for the IO and crypt workqueues
...
Pull MD updates from Shaohua Li:
- Add Partial Parity Log (ppl) feature found in Intel IMSM raid array
by Artur Paszkiewicz. This feature is another way to close RAID5
writehole. The Linux implementation is also available for normal
RAID5 array if specific superblock bit is set.
- A number of md-cluser fixes and enabling md-cluster array resize from
Guoqing Jiang
- A bunch of patches from Ming Lei and Neil Brown to rewrite MD bio
handling related code. Now MD doesn't directly access bio bvec,
bi_phys_segments and uses modern bio API for bio split.
- Improve RAID5 IO pattern to improve performance for hard disk based
RAID5/6 from me.
- Several patches from Song Liu to speed up raid5-cache recovery and
allow raid5 cache feature disabling in runtime.
- Fix a performance regression in raid1 resync from Xiao Ni.
- Other cleanup and fixes from various people.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md: (84 commits)
md/raid10: skip spare disk as 'first' disk
md/raid1: Use a new variable to count flighting sync requests
md: clear WantReplacement once disk is removed
md/raid1/10: remove unused queue
md: handle read-only member devices better.
md/raid10: wait up frozen array in handle_write_completed
uapi: fix linux/raid/md_p.h userspace compilation error
md-cluster: Fix a memleak in an error handling path
md: support disabling of create-on-open semantics.
md: allow creation of mdNNN arrays via md_mod/parameters/new_array
raid5-ppl: use a single mempool for ppl_io_unit and header_page
md/raid0: fix up bio splitting.
md/linear: improve bio splitting.
md/raid5: make chunk_aligned_read() split bios more cleanly.
md/raid10: simplify handle_read_error()
md/raid10: simplify the splitting of requests.
md/raid1: factor out flush_bio_list()
md/raid1: simplify handle_read_error().
Revert "block: introduce bio_copy_data_partial"
md/raid1: simplify alloc_behind_master_bio()
...
Remove the request_idx parameter, which can't be used safely now that we
support I/O schedulers with blk-mq. Except for a superflous check in
mtip32xx it was unused anyway.
Also pass the tag_set instead of just the driver data - this allows drivers
to avoid some code duplication in a follow on cleanup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This untangles the DM_MAPIO_* values returned from ->clone_and_map_rq
from the error codes used by the block layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Instead of returning either a DM_ENDIO_* constant or an error code, add
a new DM_ENDIO_DONE value that means keep errno as is. This allows us
to easily keep the existing error code in case where we can't push back,
and it also preparares for the new block level status codes with strict
type checking.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 6f287ca(md/raid10: reset the 'first' at the end of loop) ignores
a case in reshape, the first rdev could be a spare disk, which shouldn't
be accounted as the first disk since it doesn't include the offset info.
Fix: 6f287ca(md/raid10: reset the 'first' at the end of loop)
Cc: Guoqing Jiang <gqjiang@suse.com>
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
dm-bufio checks a watermark when it allocates a new buffer in
__bufio_new(). However, it doesn't check the watermark when the user
changes /sys/module/dm_bufio/parameters/max_cache_size_bytes.
This may result in a problem - if the watermark is high enough so that
all possible buffers are allocated and if the user lowers the value of
"max_cache_size_bytes", the watermark will never be checked against the
new value because no new buffer would be allocated.
To fix this, change __evict_old_buffers() so that it checks the
watermark. __evict_old_buffers() is called every 30 seconds, so if the
user reduces "max_cache_size_bytes", dm-bufio will react to this change
within 30 seconds and decrease memory consumption.
Depends-on: 1b0fb5a5b2 ("dm bufio: avoid a possible ABBA deadlock")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
__get_memory_limit() tests if dm_bufio_cache_size changed and calls
__cache_size_refresh() if it did. It takes dm_bufio_clients_lock while
it already holds the client lock. However, lock ordering is violated
because in cleanup_old_buffers() dm_bufio_clients_lock is taken before
the client lock.
This results in a possible deadlock and lockdep engine warning.
Fix this deadlock by changing mutex_lock() to mutex_trylock(). If the
lock can't be taken, it will be re-checked next time when a new buffer
is allocated.
Also add "unlikely" to the if condition, so that the optimizer assumes
that the condition is false.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull block layer updates from Jens Axboe:
- Add BFQ IO scheduler under the new blk-mq scheduling framework. BFQ
was initially a fork of CFQ, but subsequently changed to implement
fairness based on B-WF2Q+, a modified variant of WF2Q. BFQ is meant
to be used on desktop type single drives, providing good fairness.
From Paolo.
- Add Kyber IO scheduler. This is a full multiqueue aware scheduler,
using a scalable token based algorithm that throttles IO based on
live completion IO stats, similary to blk-wbt. From Omar.
- A series from Jan, moving users to separately allocated backing
devices. This continues the work of separating backing device life
times, solving various problems with hot removal.
- A series of updates for lightnvm, mostly from Javier. Includes a
'pblk' target that exposes an open channel SSD as a physical block
device.
- A series of fixes and improvements for nbd from Josef.
- A series from Omar, removing queue sharing between devices on mostly
legacy drivers. This helps us clean up other bits, if we know that a
queue only has a single device backing. This has been overdue for
more than a decade.
- Fixes for the blk-stats, and improvements to unify the stats and user
windows. This both improves blk-wbt, and enables other users to
register a need to receive IO stats for a device. From Omar.
- blk-throttle improvements from Shaohua. This provides a scalable
framework for implementing scalable priotization - particularly for
blk-mq, but applicable to any type of block device. The interface is
marked experimental for now.
- Bucketized IO stats for IO polling from Stephen Bates. This improves
efficiency of polled workloads in the presence of mixed block size
IO.
- A few fixes for opal, from Scott.
- A few pulls for NVMe, including a lot of fixes for NVMe-over-fabrics.
From a variety of folks, mostly Sagi and James Smart.
- A series from Bart, improving our exposed info and capabilities from
the blk-mq debugfs support.
- A series from Christoph, cleaning up how handle WRITE_ZEROES.
- A series from Christoph, cleaning up the block layer handling of how
we track errors in a request. On top of being a nice cleanup, it also
shrinks the size of struct request a bit.
- Removal of mg_disk and hd (sorry Linus) by Christoph. The former was
never used by platforms, and the latter has outlived it's usefulness.
- Various little bug fixes and cleanups from a wide variety of folks.
* 'for-4.12/block' of git://git.kernel.dk/linux-block: (329 commits)
block: hide badblocks attribute by default
blk-mq: unify hctx delay_work and run_work
block: add kblock_mod_delayed_work_on()
blk-mq: unify hctx delayed_run_work and run_work
nbd: fix use after free on module unload
MAINTAINERS: bfq: Add Paolo as maintainer for the BFQ I/O scheduler
blk-mq-sched: alloate reserved tags out of normal pool
mtip32xx: use runtime tag to initialize command header
scsi: Implement blk_mq_ops.show_rq()
blk-mq: Add blk_mq_ops.show_rq()
blk-mq: Show operation, cmd_flags and rq_flags names
blk-mq: Make blk_flags_show() callers append a newline character
blk-mq: Move the "state" debugfs attribute one level down
blk-mq: Unregister debugfs attributes earlier
blk-mq: Only unregister hctxs for which registration succeeded
blk-mq-debugfs: Rename functions for registering and unregistering the mq directory
blk-mq: Let blk_mq_debugfs_register() look up the queue name
blk-mq: Register <dev>/queue/mq after having registered <dev>/queue
ide-pm: always pass 0 error to ide_complete_rq in ide_do_devset
ide-pm: always pass 0 error to __blk_end_request_all
..
I/O errors triggered by multipathd incorrectly not enabling the no-flush
flag for DM_DEVICE_SUSPEND or DM_DEVICE_RESUME are hard to debug. Add
more logging to make it easier to debug this.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
No functional change but makes the code easier to read.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Instead of checking MPATHF_QUEUE_IF_NO_PATH,
MPATHF_SAVED_QUEUE_IF_NO_PATH and the no_flush flag to decide whether
or not to push back a request (or bio) if there are no paths available,
only clear MPATHF_QUEUE_IF_NO_PATH in queue_if_no_path() if no_flush has
not been set. The result is that only a single bit has to be tested in
the hot path to decide whether or not a request must be pushed back and
also that m->lock does not have to be taken in the hot path.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Introduce an enumeration type for the queue mode. This patch does
not change any functionality but makes the DM code easier to read.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Verify at runtime that __pg_init_all_paths() is called with
multipath.lock held if lockdep is enabled.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Ensure that the assumptions about the caller holding suspend_lock
are checked at runtime if lockdep is enabled.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The 'cache_size' argument of dm_block_manager_create() has never been
used. Remove it along with the definitions of the constants passed as
the 'cache_size' argument.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Otherwise the request-based DM blk-mq request_queue will be put into
service without being properly exported via sysfs.
Cc: stable@vger.kernel.org
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Requeuing a request immediately while path initialization is ongoing
causes high CPU usage, something that is undesired. Hence delay
requeuing while path initialization is in progress.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If blk_get_request() fails, check whether the failure is due to a path
being removed. If that is the case, fail the path by triggering a call
to fail_path(). This avoids that the following scenario can be
encountered while removing paths:
* CPU usage of a kworker thread jumps to 100%.
* Removing the DM device becomes impossible.
Delay requeueing if blk_get_request() returns -EBUSY or -EWOULDBLOCK,
and the queue is not dying, because in these cases immediate requeuing
is inappropriate.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In new barrier codes, raise_barrier waits if conf->nr_pending[idx] is not zero.
After all the conditions are true, the resync request can go on be handled. But
it adds conf->nr_pending[idx] again. The next resync request hit the same bucket
idx need to wait the resync request which is submitted before. The performance
of resync/recovery is degraded.
So we should use a new variable to count sync requests which are in flight.
I did a simple test:
1. Without the patch, create a raid1 with two disks. The resync speed:
Device: rrqm/s wrqm/s r/s w/s rMB/s wMB/s avgrq-sz avgqu-sz await r_await w_await svctm %util
sdb 0.00 0.00 166.00 0.00 10.38 0.00 128.00 0.03 0.20 0.20 0.00 0.19 3.20
sdc 0.00 0.00 0.00 166.00 0.00 10.38 128.00 0.96 5.77 0.00 5.77 5.75 95.50
2. With the patch, the result is:
sdb 2214.00 0.00 766.00 0.00 185.69 0.00 496.46 2.80 3.66 3.66 0.00 1.03 79.10
sdc 0.00 2205.00 0.00 769.00 0.00 186.44 496.52 5.25 6.84 0.00 6.84 1.30 100.10
Suggested-by: Shaohua Li <shli@kernel.org>
Signed-off-by: Xiao Ni <xni@redhat.com>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
activate_path() is renamed to activate_path_work() which now calls
activate_or_offline_path(). activate_or_offline_path() will be used
by the next commit.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When calling a dm ioctl that doesn't process any data
(IOCTL_FLAGS_NO_PARAMS), the contents of the data field in struct
dm_ioctl are left initialized. Current code is incorrectly extending
the size of data copied back to user, causing the contents of kernel
stack to be leaked to user. Fix by only copying contents before data
and allow the functions processing the ioctl to override.
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Salido <salidoa@google.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The log2 of sectors_per_block was already calculated, so we don't have
to use the ilog2 function.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There is no need to have a duplication of the generic library, i.e. hex2bin().
Replace the open coded variant.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Now that all the producers and consumers of dax interfaces have been
converted to using dax_operations on a dax_device, remove the block
device direct_access enabling.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Arrange for dm to lookup the dax services available from member devices.
Update the dax-capable targets, linear and stripe, to route dax
operations to the underlying device. Changes the target-internal
->direct_access() method to more closely align with the dax_operations
->direct_access() calling convention.
Cc: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
dm-crypt used to use separate crypto transforms for each CPU, but this
is no longer the case. To avoid confusion, fix up obsolete comments and
rename setup_essiv_cpu().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
We can clear 'WantReplacement' flag directly no
matter it's replacement existed or not since the
semantic is same as before.
Also since the disk is removed from array, then
it is straightforward to remove 'WantReplacement'
flag and the comments in raid10/5 can be removed
as well.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Use of the synchronous digest API limits dm-verity to using pure
CPU based algorithm providers and rules out the use of off CPU
algorithm providers which are normally asynchronous by nature,
potentially freeing CPU cycles.
This can reduce performance per Watt in situations such as during
boot time when a lot of concurrent file accesses are made to the
protected volume.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: Eric Biggers <ebiggers3@gmail.com>
CC: Ondrej Mosnáček <omosnacek+linux-crypto@gmail.com>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Running dm-crypt with workqueues at the standard priority results in IO
competing for CPU time with standard user apps, which can lead to
pipeline bubbles and seriously degraded performance. Move to using
WQ_HIGHPRI workqueues to protect against that.
Signed-off-by: Tim Murray <timmurray@google.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The message "key wipe" used to wipe real key stored in crypto layer by
rewriting it with zeroes. Since commit 28856a9 ("crypto: xts -
consolidate sanity check for keys") this no longer works in FIPS mode
for XTS.
While running in FIPS mode the crypto key part has to differ from the
tweak key.
Fixes: 28856a9 ("crypto: xts - consolidate sanity check for keys")
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If blk_get_request() returns ENODEV then multipath_clone_and_map()
causes a request to be requeued immediately. This can cause a kworker
thread to spend 100% of the CPU time of a single core in
__blk_mq_run_hw_queue() and also can cause device removal to never
finish.
Avoid this by only requeuing after a delay if blk_get_request() fails.
Additionally, reduce the requeue delay.
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When committing era metadata to disk, it doesn't always save the latest
spacemap metadata root in superblock. Due to this, metadata is getting
corrupted sometimes when reopening the device. The correct order of update
should be, pre-commit (shadows spacemap root), save the spacemap root
(newly shadowed block) to in-core superblock and then the final commit.
Cc: stable@vger.kernel.org
Signed-off-by: Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm_btree_find_lowest_key() is giving incorrect results. find_key()
traverses the btree correctly for finding the highest key, but there is
an error in the way it traverses the btree for retrieving the lowest
key. dm_btree_find_lowest_key() fetches the first key of the rightmost
block of the btree instead of fetching the first key from the leftmost
block.
Fix this by conditionally passing the correct parameter to value64()
based on the @find_highest flag.
Cc: stable@vger.kernel.org
Signed-off-by: Erez Zadok <ezk@fsl.cs.sunysb.edu>
Signed-off-by: Vinothkumar Raja <vinraja@cs.stonybrook.edu>
Signed-off-by: Nidhi Panpalia <npanpalia@cs.stonybrook.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The extra pair of parantheses is not needed and causes clang to generate
warnings about the DM_DEV_CREATE_CMD comparison in validate_params().
Also remove another double parentheses that doesn't cause a warning.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This dummy structure definition was required for RCU macros, but it
isn't required anymore, so delete it.
The dummy definition confuses the crash tool, see:
https://www.redhat.com/archives/dm-devel/2017-April/msg00197.html
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Previously, dm-crypt could use blocks composed of multiple 512b sectors
but it created integrity profile for each 512b sector (it padded it with
zeroes). Fix dm-crypt so that the integrity profile is sent for each
block not each sector.
The user must use the same block size in the DM crypt and integrity
targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The DM integrity block size can now be 512, 1k, 2k or 4k. Using larger
blocks reduces metadata handling overhead. The block size can be
configured at table load time using the "block_size:<value>" option;
where <value> is expressed in bytes (defult is still 512 bytes).
It is safe to use larger block sizes with DM integrity, because the
DM integrity journal makes sure that the whole block is updated
atomically even if the underlying device doesn't support atomic writes
of that size (e.g. 4k block ontop of a 512b device).
Depends-on: 2859323e ("block: fix blk_integrity_register to use template's interval_exp if not 0")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Some coding style changes.
Fix a bug that the array test_tag has insufficient size if the digest
size of internal has is bigger than the tag size.
The function __fls is undefined for zero argument, this patch fixes
undefined behavior if the user sets zero interleave_sectors.
Fix the limit of optional arguments to 8.
Don't allocate crypt_data on the stack to avoid a BUG with debug kernel.
Rename all optional argument names to have underscores rather than
dashes.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A dm-crypt on dm-integrity device incorrectly advertises an integrity
profile on the DM crypt device. It can be seen in the files
"/sys/block/dm-*/integrity/*" that both dm-integrity and dm-crypt target
advertise the integrity profile. That is incorrect, only the
dm-integrity target should advertise the integrity profile.
A general problem in DM is that if we have a DM device that depends on
another device with an integrity profile, the upper device will always
advertise the integrity profile, even when the target driver doesn't
support handling integrity data.
Most targets don't support integrity data, so we provide a whitelist of
targets that support it (linear, delay and striped). The targets that
support passing integrity data to the lower device are marked with the
flag DM_TARGET_PASSES_INTEGRITY. The DM core will now advertise
integrity data on a DM device only if all the targets support the
integrity data.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Also remove some unnecessary use of uninitialized_var().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A queue is declared and get from the disk of the array, but it's not
used anywhere. So removing it from the source.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Acted-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
1/ If an array has any read-only devices when it is started,
the array itself must be read-only
2/ A read-only device cannot be added to an array after it is
started.
3/ Setting an array to read-write should not succeed
if any member devices are read-only
Reported-and-Tested-by: Nanda Kishore Chinnaram <Nanda_Kishore_Chinna@dell.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Allocate a dax_device to represent the capacity of a device-mapper
instance. Provide a ->direct_access() method via the new dax_operations
indirection that mirrors the functionality of the current direct_access
support via block_device_operations. Once fs/dax.c has been converted
to use dax_operations the old dm_blk_direct_access() will be removed.
A new helper dm_dax_get_live_target() is introduced to separate some of
the dm-specifics from the direct_access implementation.
This enabling is only for the top-level dm representation to upper
layers. Converting target direct_access implementations is deferred to a
separate patch.
Cc: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that all drivers that call blk_mq_complete_requests have a
->complete callback we can remove the direct call to blk_mq_end_request,
as well as the error argument to blk_mq_complete_request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We'll get all proper errors reported through ->end_io and ->errors will
go away soon.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
dm never uses rq->errors, so there is no need to pass an error argument
to blk_mq_complete_request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since nr_queued is changed, we need to call wake_up here
if the array is already frozen and waiting for condition
"nr_pending == nr_queued + extra" to be true.
And commit 824e47dadd ("RAID1: avoid unnecessary spin
locks in I/O barrier code") which has already added the
wake_up for raid1.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We know that 'bm_lockres' is NULL here, so 'lockres_free(bm_lockres)' is a
no-op. According to resource handling in case of error a few lines below,
it is likely that 'bitmap_free(bitmap)' was expected instead.
Fixes: b98938d16a ("md-cluster: introduce cluster_check_sync_size")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
md allows a new array device to be created by simply
opening a device file. This make it difficult to
remove the device and udev is likely to open the device file
as part of processing the REMOVE event.
There is an alternate mechanism for creating arrays
by writing to the new_array module parameter.
When using tools that work with this parameter, it is
best to disable the old semantics.
This new module parameter allows that.
Signed-off-by: NeilBrown <neilb@suse.com>
Acted-by: Coly Li <colyli@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
The intention when creating the "new_array" parameter and the
possibility of having array names line "md_HOME" was to transition
away from the old way of creating arrays and to eventually only use
this new way.
The "old" way of creating array is to create a device node in /dev
and then open it. The act of opening creates the array.
This is problematic because sometimes the device node can be opened
when we don't want to create an array. This can easily happen
when some rule triggered by udev looks at a device as it is being
destroyed. The node in /dev continues to exist for a short period
after an array is stopped, and opening it during this time recreates
the array (as an inactive array).
Unfortunately no clear plan for the transition was created. It is now
time to fix that.
This patch allows devices with numeric names, like "md999" to be
created by writing to "new_array". This will only work if the minor
number given is not already in use. This will allow mdadm to
support the creation of arrays with numbers > 511 (currently not
possible) by writing to new_array.
mdadm can, at some point, use this approach to create *all* arrays,
which will allow the transition to only using the new-way.
Signed-off-by: NeilBrown <neilb@suse.com>
Acted-by: Coly Li <colyli@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
Allocate both struct ppl_io_unit and its header_page from a shared
mempool to avoid a possible deadlock. Implement allocate and free
functions for the mempool, remove the second pool for allocating
header_page. The header_pages are now freed with their io_units, not
when the ppl bio completes. Also, use GFP_NOWAIT instead of GFP_ATOMIC
for allocating ppl_io_unit because we can handle failed allocations and
there is no reason to utilize emergency reserves.
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
raid0_make_request() should use a private bio_set rather than the
shared fs_bio_set, which is only meant for filesystems to use.
raid0_make_request() shouldn't loop around using the bio_set
multiple times as that can deadlock.
So use mddev->bio_set and pass the tail to generic_make_request()
instead of looping on it.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
linear_make_request() uses fs_bio_set, which is meant for filesystems
to use, and loops, possible allocating from the same bio set multiple
times.
These behaviors can theoretically cause deadlocks, though as
linear requests are hardly ever split, it is unlikely in practice.
Change to use mddev->bio_set - otherwise unused for linear, and submit
the tail of a split request to generic_make_request() for it to
handle.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
chunk_aligned_read() currently uses fs_bio_set - which is meant for
filesystems to use - and loops if multiple splits are needed, which is
not best practice.
As this is only used for READ requests, not writes, it is unlikely
to cause a problem. However it is best to be consistent in how
we split bios, and to follow the pattern used in raid1/raid10.
So create a private bioset, bio_split, and use it to perform a single
split, submitting the remainder to generic_make_request() for later
processing.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
handle_read_error() duplicates a lot of the work that raid10_read_request()
does, so it makes sense to just use that function.
handle_read_error() relies on the same r10bio being re-used so that,
in the case of a read-only array, setting IO_BLOCKED in r1bio->devs[].bio
ensures read_balance() won't re-use that device.
So when called from raid10_make_request() we clear that array, but not
when called from handle_read_error().
Two parts of handle_read_error() that need to be preserved are the warning
message it prints, so they are conditionally added to
raid10_read_request(). If the failing rdev can be found, messages
are printed. Otherwise they aren't.
Not that as rdev_dec_pending() has already been called on the failing
rdev, we need to use rcu_read_lock() to get a new reference from
the conf. We only use this to get the name of the failing block device.
With this change, we no longer need inc_pending().
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
raid10 splits requests in two different ways for two different
reasons.
First, bio_split() is used to ensure the bio fits with a chunk.
Second, multiple r10bio structures are allocated to represent the
different sections that need to go to different devices, to avoid
known bad blocks.
This can be simplified to just use bio_split() once, and not to use
multiple r10bios.
We delay the split until we know a maximum bio size that can
be handled with a single r10bio, and then split the bio and queue
the remainder for later handling.
As with raid1, we allocate a new bio_set to help with the splitting.
It is not correct to use fs_bio_set in a device driver.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
flush_pending_writes() and raid1_unplug() each contain identical
copies of a fairly large slab of code. So factor that out into
new flush_bio_list() to simplify maintenance.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
handle_read_error() duplicates a lot of the work that raid1_read_request()
does, so it makes sense to just use that function.
This doesn't quite work as handle_read_error() relies on the same r1bio
being re-used so that, in the case of a read-only array, setting
IO_BLOCKED in r1bio->bios[] ensures read_balance() won't re-use
that device.
So we need to allow a r1bio to be passed to raid1_read_request(), and to
have that function mostly initialise the r1bio, but leave the bios[]
array untouched.
Two parts of handle_read_error() that need to be preserved are the warning
message it prints, so they are conditionally added to raid1_read_request().
Note that this highlights a minor bug on alloc_r1bio(). It doesn't
initalise the bios[] array, so it is possible that old content is there,
which might cause read_balance() to ignore some devices with no good reason.
With this change, we no longer need inc_pending(), or the sectors_handled
arg to alloc_r1bio().
As handle_read_error() is called from raid1d() and allocates memory,
there is tiny chance of a deadlock. All element of various pools
could be queued waiting for raid1 to handle them, and there may be no
extra memory free.
Achieving guaranteed forward progress would probably require a second
thread and another mempool. Instead of that complexity, add
__GFP_HIGH to any allocations when read1_read_request() is called
from raid1d.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Now that we always always pass an offset of 0 and a size
that matches the bio to alloc_behind_master_bio(),
we can remove the offset/size args and simplify the code.
We could probably remove bio_copy_data_partial() too.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
raid1 currently splits requests in two different ways for
two different reasons.
First, bio_split() is used to ensure the bio fits within a
resync accounting region.
Second, multiple r1bios are allocated for each bio to handle
the possiblity of known bad blocks on some devices.
This can be simplified to just use bio_split() once, and not
use multiple r1bios.
We delay the split until we know a maximum bio size that can
be handled with a single r1bio, and then split the bio and
queue the remainder for later handling.
This avoids all loops inside raid1.c request handling. Just
a single read, or a single set of writes, is submitted to
lower-level devices for each bio that comes from
generic_make_request().
When the bio needs to be split, generic_make_request() will
do the necessary looping and call md_make_request() multiple
times.
raid1_make_request() no longer queues request for raid1 to handle,
so we can remove that branch from the 'if'.
This patch also creates a new private bio_set
(conf->bio_split) for splitting bios. Using fs_bio_set
is wrong, as it is meant to be used by filesystems, not
block devices. Using it inside md can lead to deadlocks
under high memory pressure.
Delete unused variable in raid1_write_request() (Shaohua)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
In case of read-modify-write, partial partity is the same as the result
of ops_run_prexor5(), so we can just copy sh->dev[pd_idx].page into
sh->ppl_page instead of calculating it again.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Use resize_stripes() instead of raid5_reset_stripe_cache() to allocate
or free sh->ppl_page at runtime for all stripes in the stripe cache.
raid5_reset_stripe_cache() required suspending the mddev and could
deadlock because of GFP_KERNEL allocations.
Move the 'newsize' check to check_reshape() to allow reallocating the
stripes with the same number of disks. Allocate sh->ppl_page in
alloc_stripe() instead of grow_buffers(). Pass 'struct r5conf *conf' as
a parameter to alloc_stripe() because it is needed to check whether to
allocate ppl_page. Add free_stripe() and use it to free stripes rather
than directly call kmem_cache_free(). Also free sh->ppl_page in
free_stripe().
Set MD_HAS_PPL at the end of ppl_init_log() instead of explicitly
setting it in advance and add another parameter to log_init() to allow
calling ppl_init_log() without the bit set. Don't try to calculate
partial parity or add a stripe to log if it does not have ppl_page set.
Enabling ppl can now be performed without suspending the mddev, because
the log won't be used until new stripes are allocated with ppl_page.
Calling mddev_suspend/resume is still necessary when disabling ppl,
because we want all stripes to finish before stopping the log, but
resize_stripes() can be called after mddev_resume() when ppl is no
longer active.
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Use a single no_mem_stripes list instead of per member device lists for
handling stripes that need retrying in case of failed io_unit
allocation. Because io_units are allocated from a memory pool shared
between all member disks, the no_mem_stripes list should be checked when
an io_unit for any member is freed. This fixes a deadlock that could
happen if there are stripes in more than one no_mem_stripes list.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
fix_sync_read_error() modifies a bio on a newly faulty
device by setting bi_end_io to end_sync_write.
This ensure that put_buf() will still call rdev_dec_pending()
as required, but makes sure that subsequent code in
fix_sync_read_error() doesn't try to read from the device.
Unfortunately this interacts badly with sync_request_write()
which assumes that any bio with bi_end_io set to non-NULL
other than end_sync_read is safe to write to.
As the device is now faulty it doesn't make sense to write.
As the bio was recently used for a read, it is "dirty"
and not suitable for immediate submission.
In particular, ->bi_next might be non-NULL, which will cause
generic_make_request() to complain.
Break this interaction by refusing to write to devices
which are marked as Faulty.
Reported-and-tested-by: Michael Wang <yun.wang@profitbricks.com>
Fixes: 2e52d449bc ("md/raid1: add failfast handling for reads.")
Cc: stable@vger.kernel.org (v4.10+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
md.c: it needs to release the mddev lock before
the array_size_store() returns.
Fixes: ab5a98b132 ("md-cluster: change array_sectors and update size are not supported")
Signed-off-by: Zhilong Liu <zlliu@suse.com>
Reviewed-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
if called md_set_readonly and set MD_CLOSING bit, the mddev cannot
be opened any more due to the MD_CLOING bit wasn't cleared. Thus it
needs to be cleared in md_ioctl after any call to md_set_readonly()
or do_md_stop().
Signed-off-by: NeilBrown <neilb@suse.com>
Fixes: af8d8e6f03 ("md: changes for MD_STILL_CLOSED flag")
Cc: stable@vger.kernel.org (v4.9+)
Signed-off-by: Zhilong Liu <zlliu@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We need to set "first = 0' at the end of rdev_for_each
loop, so we can get the array's min_offset_diff correctly
otherwise min_offset_diff just means the last rdev's
offset diff.
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When recoverying a single missing/failed device in a RAID6,
those stripes where the Q block is on the missing device are
handled a bit differently. In these cases it is easy to
check that the P block is correct, so we do. This results
in the P block be destroy. Consequently the P block needs
to be read a second time in order to compute Q. This causes
lots of seeks and hurts performance.
It shouldn't be necessary to re-read P as it can be computed
from the DATA. But we only compute blocks on missing
devices, since c337869d95 ("md: do not compute parity
unless it is on a failed drive").
So relax the change made in that commit to allow computing
of the P block in a RAID6 which it is the only missing that
block.
This makes RAID6 recovery run much faster as the disk just
"before" the recovering device is no longer seeking
back-and-forth.
Reported-by-tested-by: Brad Campbell <lists2009@fnarfbargle.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull block fixes from Jens Axboe:
"Here's a pull request for 4.11-rc, fixing a set of issues mostly
centered around the new scheduling framework. These have been brewing
for a while, but split up into what we absolutely need in 4.11, and
what we can defer until 4.12. These are well tested, on both single
queue and multiqueue setups, and with and without shared tags. They
fix several hangs that have happened in testing.
This is obviously larger than I would have preferred at this point in
time, but I don't think we can shave much off this and still get the
desired results.
In detail, this pull request contains:
- a set of five fixes for NVMe, mostly from Christoph and one from
Roland.
- a series from Bart, fixing issues with dm-mq and SCSI shared tags
and scheduling. Note that one of those patches commit messages may
read like an optimization, but it is in fact an important fix for
queue restarts in particular.
- a series from Omar, most importantly fixing a hang with multiple
hardware queues when we fail to get a driver tag. Another important
fix in there is for resizing hardware queues, which nbd does when
handling multiple sockets for one connection.
- fixing an imbalance in putting the ctx for hctx request allocations
from Minchan"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: Restart a single queue if tag sets are shared
dm rq: Avoid that request processing stalls sporadically
scsi: Avoid that SCSI queues get stuck
blk-mq: Introduce blk_mq_delay_run_hw_queue()
blk-mq: remap queues when adding/removing hardware queues
blk-mq-sched: fix crash in switch error path
blk-mq-sched: set up scheduler tags when bringing up new queues
blk-mq-sched: refactor scheduler initialization
blk-mq: use the right hctx when getting a driver tag fails
nvmet: fix byte swap in nvmet_parse_io_cmd
nvmet: fix byte swap in nvmet_execute_write_zeroes
nvmet: add missing byte swap in nvmet_get_smart_log
nvme: add missing byte swap in nvme_setup_discard
nvme: Correct NVMF enum values to match NVMe-oF rev 1.0
block: do not put mq context in blk_mq_alloc_request_hctx
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can
kill this hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It seems like the code currently passes whatever it was using for writes
to WRITE SAME. Just switch it to WRITE ZEROES, although that doesn't
need any payload.
Untested, and confused by the code, maybe someone who understands it
better than me can help..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Copy & paste from the REQ_OP_WRITE_SAME code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix up do_region to not allocate a bio_vec for discards. We've
got rid of the discard payload allocated by the caller years ago.
Obviously this wasn't actually harmful given how long it's been
there, but it's still good to avoid the pointless allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Copy & paste from the REQ_OP_WRITE_SAME code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We've added a considerable amount of fixes for stalls and issues
with the blk-mq scheduling in the 4.11 series since forking
off the for-4.12/block branch. We need to do improvements on
top of that for 4.12, so pull in the previous fixes to make
our lives easier going forward.
Signed-off-by: Jens Axboe <axboe@fb.com>
While running the srp-test software I noticed that request
processing stalls sporadically at the beginning of a test, namely
when mkfs is run against a dm-mpath device. Every time when that
happened the following command was sufficient to resume request
processing:
echo run >/sys/kernel/debug/block/dm-0/state
This patch avoids that such request processing stalls occur. The
test I ran is as follows:
while srp-test/run_tests -d -r 30 -t 02-mq; do :; done
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Jens Axboe <axboe@fb.com>
- A stable@ fix for raid target's raid1 support (when no bitmap is used)
- A 4.11 cache metadata v2 format fix to properly test blocks are clean
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY56smAAoJEMUj8QotnQNa3xYH/39l25eGzam0cnITa31cX9uu
lb+oWnqbgvbd65HZr2QPu9RO8LQMK9wxw40wapyYTEnkDfgeW+hmwYo3BUZ0IpdT
Ry39KGCGaxk3L3cATSgtZT18AsWRHmKqlHLf6y98RdeFLVb3lyUFllkLF9r3M2ep
1Ga2MiMJYffaiTsSKxwZQG3XG7mq9MNfRnCehGAQwjGgWL3EsYHNsq+Hosn/tdtZ
2D7BvAMr2X+3xEUVevqL2dFmJ1D2tbJjtedeAKVOccErV/BofwWPUvTOFX8202+Y
CUC9pW+hDQqpCm15Pr4N6oU4TeC4mHMwGK0SLWmoXkl3VDPbUUO3qC5AwKxsepA=
=cWkE
-----END PGP SIGNATURE-----
Merge tag 'dm-4.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- two stable fixes for the verity target's FEC support
- a stable fix for raid target's raid1 support (when no bitmap is used)
- a 4.11 cache metadata v2 format fix to properly test blocks are clean
* tag 'dm-4.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm verity fec: fix bufio leaks
dm raid: fix NULL pointer dereference for raid1 without bitmap
dm cache metadata: fix metadata2 format's blocks_are_clean_separate_dirty
dm verity fec: limit error correction recursion
Currently only dm and md/raid5 bios trigger
trace_block_bio_complete(). Now that we have bio_chain() and
bio_inc_remaining(), it is not possible, in general, for a driver to
know when the bio is really complete. Only bio_endio() knows that.
So move the trace_block_bio_complete() call to bio_endio().
Now trace_block_bio_complete() pairs with trace_block_bio_queue().
Any bio for which a 'queue' event is traced, will subsequently
generate a 'complete' event.
There are a few cases where completion tracing is not wanted.
1/ If blk_update_request() has already generated a completion
trace event at the 'request' level, there is no point generating
one at the bio level too. In this case the bi_sector and bi_size
will have changed, so the bio level event would be wrong
2/ If the bio hasn't actually been queued yet, but is being aborted
early, then a trace event could be confusing. Some filesystems
call bio_endio() but do not want tracing.
3/ The bio_integrity code interposes itself by replacing bi_end_io,
then restoring it and calling bio_endio() again. This would produce
two identical trace events if left like that.
To handle these, we introduce a flag BIO_TRACE_COMPLETION and only
produce the trace event when this is set.
We address point 1 above by clearing the flag in blk_update_request().
We address point 2 above by only setting the flag when
generic_make_request() is called.
We address point 3 above by clearing the flag after generating a
completion event.
When bio_split() is used on a bio, particularly in blk_queue_split(),
there is an extra complication. A new bio is split off the front, and
may be handle directly without going through generic_make_request().
The old bio, which has been advanced, is passed to
generic_make_request(), so it will trigger a trace event a second
time.
Probably the best result when a split happens is to see a single
'queue' event for the whole bio, then multiple 'complete' events - one
for each component. To achieve this was can:
- copy the BIO_TRACE_COMPLETION flag to the new bio in bio_split()
- avoid generating a 'queue' event if BIO_TRACE_COMPLETION is already set.
This way, the split-off bio won't create a queue event, the original
won't either even if it re-submitted to generic_make_request(),
but both will produce completion events, each for their own range.
So if generic_make_request() is called (which generates a QUEUED
event), then bi_endio() will create a single COMPLETE event for each
range that the bio is split into, unless the driver has explicitly
requested it not to.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Buffers read through dm_bufio_read() were not released in all code paths.
Fixes: a739ff3f54 ("dm verity: add support for forward error correction")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
By ignoring the sentinels the cleaner policy is able to write-back dirty
cache data much faster. There is no reason to respect the sentinels,
which denote that a block was changed recently, when using the cleaner
policy given that the cleaner is tasked with writing back all dirty
data.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When loading metadata make sure to set/clear the dirty bits in the cache
core's dirty_bitset as well as the policy.
Otherwise the cache core is unaware that any blocks were dirty when the
cache was last shutdown. A very serious side-effect being that the
cleaner policy would therefore never be tasked with writing back dirty
data from a cache that was in writeback mode (e.g. when switching from
smq policy to cleaner policy when decommissioning a writeback cache).
This fixes a serious data corruption bug associated with writeback mode.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Constify all instances of blk_mq_ops, as they are never modified.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since the commit 0cf4503174 ("dm raid: add support for the MD RAID0
personality"), the dm-raid subsystem can activate a RAID-0 array.
Therefore, add MD_RAID0 to the dependencies of DM_RAID, so that MD_RAID0
will be selected when DM_RAID is selected.
Fixes: 0cf4503174 ("dm raid: add support for the MD RAID0 personality")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This patch kills the warning reported on powerpc_pseries,
and actually we don't need the initialization.
After merging the md tree, today's linux-next build (powerpc
pseries_le_defconfig) produced this warning:
drivers/md/raid1.c: In function 'raid1d':
drivers/md/raid1.c:2172:9: warning: 'page_len$' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (memcmp(page_address(ppages[j]),
^
drivers/md/raid1.c:2160:7: note: 'page_len$' was declared here
int page_len[RESYNC_PAGES];
^
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
URLs to ftp.kernel.org are still exist though the service is closed [0].
This commit fixes the URLs to use www.kernel.org instead.
[0] https://www.kernel.org/shutting-down-ftp-services.html
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When journal device of an array fails, the array is forced into read-only
mode. To make the array normal without adding another journal device, we
need to remove journal _feature_ from the array.
This patch allows remove journal _feature_ from an array, For journal
existing journal should be either missing or faulty.
To remove journal feature, it is necessary to remove the journal device
first:
mdadm --fail /dev/md0 /dev/sdb
mdadm: set /dev/sdb faulty in /dev/md0
mdadm --remove /dev/md0 /dev/sdb
mdadm: hot removed /dev/sdb from /dev/md0
Then the journal feature can be removed by echoing into the sysfs file:
cat /sys/block/md0/md/consistency_policy
journal
echo resync > /sys/block/md0/md/consistency_policy
cat /sys/block/md0/md/consistency_policy
resync
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Commit 63c32ed4af ("dm raid: add raid4/5/6 journaling support") added
journal support to close the raid4/5/6 "write hole" -- in terms of
writethrough caching.
Introduce a "journal_mode" feature and use the new
r5c_journal_mode_set() API to add support for switching the journal
device's cache mode between write-through (the current default) and
write-back.
NOTE: If the journal device is not layered on resilent storage and it
fails, write-through mode will cause the "write hole" to reoccur. But
if the journal fails while in write-back mode it will cause data loss
for any dirty cache entries unless resilent storage is used for the
journal.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 3a1c1ef2f ("dm raid: enhance status interface and fixup
takeover/raid0") added new table line arguments and introduced an
ordering flaw. The sequence of the raid10_copies and raid10_format
raid parameters got reversed which causes lvm2 userspace to fail by
falsely assuming a changed table line.
Sequence those 2 parameters as before so that old lvm2 can function
properly with new kernels by adjusting the table line output as
documented in Documentation/device-mapper/dm-raid.txt.
Also, add missing version 1.10.1 highlight to the documention.
Fixes: 3a1c1ef2f ("dm raid: enhance status interface and fixup takeover/raid0")
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 2ded370373 ("md/r5cache: State machine for raid5-cache write
back mode") added support for "write-back" caching on the raid journal
device.
In order to allow the dm-raid target to switch between the available
"write-through" and "write-back" modes, provide a new
r5c_journal_mode_set() API.
Use the new API in existing r5c_journal_mode_store()
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Acked-by: Shaohua Li <shli@fb.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The payload->header.type and payload->size are little-endian, so just
convert them to the right byte order.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Cc: <stable@vger.kernel.org> #v4.10+
Signed-off-by: Shaohua Li <shli@fb.com>
discard request doesn't have data attached, so it's meaningless to
allocate memory and copy from original bio for behind IO. And the copy
is bogus because bio_copy_data_partial can't handle discard request.
We don't support writesame/writezeros request so far.
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
sector_div is very slow, so we introduce a variable sector_shift and
use shift instead of sector_div.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In recovery mode, we don't:
- replay the journal
- check checksums
- allow writes to the device
This mode can be used as a last resort for data recovery. The
motivation for recovery mode is that when there is a single error in the
journal, the user should not lose access to the whole device.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add optional "sector_size" parameter that specifies encryption sector
size (atomic unit of block device encryption).
Parameter can be in range 512 - 4096 bytes and must be power of two.
For compatibility reasons, the maximal IO must fit into the page limit,
so the limit is set to the minimal page size possible (4096 bytes).
NOTE: this device cannot yet be handled by cryptsetup if this parameter
is set.
IV for the sector is calculated from the 512 bytes sector offset unless
the iv_large_sectors option is used.
Test script using dmsetup:
DEV="/dev/sdb"
DEV_SIZE=$(blockdev --getsz $DEV)
KEY="9c1185a5c5e9fc54612808977ee8f548b2258d31ddadef707ba62c166051b9e3cd0294c27515f2bccee924e8823ca6e124b8fc3167ed478bca702babe4e130ac"
BLOCK_SIZE=4096
# dmsetup create test_crypt --table "0 $DEV_SIZE crypt aes-xts-plain64 $KEY 0 $DEV 0 1 sector_size:$BLOCK_SIZE"
# dmsetup table --showkeys test_crypt
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
For the new authenticated encryption we have to support generic composed
modes (combination of encryption algorithm and authenticator) because
this is how the kernel crypto API accesses such algorithms.
To simplify the interface, we accept an algorithm directly in crypto API
format. The new format is recognised by the "capi:" prefix. The
dmcrypt internal IV specification is the same as for the old format.
The crypto API cipher specifications format is:
capi:cipher_api_spec-ivmode[:ivopts]
Examples:
capi:cbc(aes)-essiv:sha256 (equivalent to old aes-cbc-essiv:sha256)
capi:xts(aes)-plain64 (equivalent to old aes-xts-plain64)
Examples of authenticated modes:
capi:gcm(aes)-random
capi:authenc(hmac(sha256),xts(aes))-random
capi:rfc7539(chacha20,poly1305)-random
Authenticated modes can only be configured using the new cipher format.
Note that this format allows user to specify arbitrary combinations that
can be insecure. (Policy decision is done in cryptsetup userspace.)
Authenticated encryption algorithms can be of two types, either native
modes (like GCM) that performs both encryption and authentication
internally, or composed modes where user can compose AEAD with separate
specification of encryption algorithm and authenticator.
For composed mode with HMAC (length-preserving encryption mode like an
XTS and HMAC as an authenticator) we have to calculate HMAC digest size
(the separate authentication key is the same size as the HMAC digest).
Introduce crypt_ctr_auth_cipher() to parse the crypto API string to get
HMAC algorithm and retrieve digest size from it.
Also, for HMAC composed mode we need to parse the crypto API string to
get the cipher mode nested in the specification. For native AEAD mode
(like GCM), we can use crypto_tfm_alg_name() API to get the cipher
specification.
Because the HMAC composed mode is not processed the same as the native
AEAD mode, the CRYPT_MODE_INTEGRITY_HMAC flag is no longer needed and
"hmac" specification for the table integrity argument is removed.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Allow the use of per-sector metadata, provided by the dm-integrity
module, for integrity protection and persistently stored per-sector
Initialization Vector (IV). The underlying device must support the
"DM-DIF-EXT-TAG" dm-integrity profile.
The per-bio integrity metadata is allocated by dm-crypt for every bio.
Example of low-level mapping table for various types of use:
DEV=/dev/sdb
SIZE=417792
# Additional HMAC with CBC-ESSIV, key is concatenated encryption key + HMAC key
SIZE_INT=389952
dmsetup create x --table "0 $SIZE_INT integrity $DEV 0 32 J 0"
dmsetup create y --table "0 $SIZE_INT crypt aes-cbc-essiv:sha256 \
11ff33c6fb942655efb3e30cf4c0fd95f5ef483afca72166c530ae26151dd83b \
00112233445566778899aabbccddeeff00112233445566778899aabbccddeeff \
0 /dev/mapper/x 0 1 integrity:32:hmac(sha256)"
# AEAD (Authenticated Encryption with Additional Data) - GCM with random IVs
# GCM in kernel uses 96bits IV and we store 128bits auth tag (so 28 bytes metadata space)
SIZE_INT=393024
dmsetup create x --table "0 $SIZE_INT integrity $DEV 0 28 J 0"
dmsetup create y --table "0 $SIZE_INT crypt aes-gcm-random \
11ff33c6fb942655efb3e30cf4c0fd95f5ef483afca72166c530ae26151dd83b \
0 /dev/mapper/x 0 1 integrity:28:aead"
# Random IV only for XTS mode (no integrity protection but provides atomic random sector change)
SIZE_INT=401272
dmsetup create x --table "0 $SIZE_INT integrity $DEV 0 16 J 0"
dmsetup create y --table "0 $SIZE_INT crypt aes-xts-random \
11ff33c6fb942655efb3e30cf4c0fd95f5ef483afca72166c530ae26151dd83b \
0 /dev/mapper/x 0 1 integrity:16:none"
# Random IV with XTS + HMAC integrity protection
SIZE_INT=377656
dmsetup create x --table "0 $SIZE_INT integrity $DEV 0 48 J 0"
dmsetup create y --table "0 $SIZE_INT crypt aes-xts-random \
11ff33c6fb942655efb3e30cf4c0fd95f5ef483afca72166c530ae26151dd83b \
00112233445566778899aabbccddeeff00112233445566778899aabbccddeeff \
0 /dev/mapper/x 0 1 integrity:48:hmac(sha256)"
Both AEAD and HMAC protection authenticates not only data but also
sector metadata.
HMAC protection is implemented through autenc wrapper (so it is
processed the same way as an authenticated mode).
In HMAC mode there are two keys (concatenated in dm-crypt mapping
table). First is the encryption key and the second is the key for
authentication (HMAC). (It is userspace decision if these keys are
independent or somehow derived.)
The sector request for AEAD/HMAC authenticated encryption looks like this:
|----- AAD -------|------ DATA -------|-- AUTH TAG --|
| (authenticated) | (auth+encryption) | |
| sector_LE | IV | sector in/out | tag in/out |
For writes, the integrity fields are calculated during AEAD encryption
of every sector and stored in bio integrity fields and sent to
underlying dm-integrity target for storage.
For reads, the integrity metadata is verified during AEAD decryption of
every sector (they are filled in by dm-integrity, but the integrity
fields are pre-allocated in dm-crypt).
There is also an experimental support in cryptsetup utility for more
friendly configuration (part of LUKS2 format).
Because the integrity fields are not valid on initial creation, the
device must be "formatted". This can be done by direct-io writes to the
device (e.g. dd in direct-io mode). For now, there is available trivial
tool to do this, see: https://github.com/mbroz/dm_int_tools
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Ondrej Mosnacek <omosnacek@gmail.com>
Signed-off-by: Vashek Matyas <matyas@fi.muni.cz>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The dm-integrity target emulates a block device that has additional
per-sector tags that can be used for storing integrity information.
A general problem with storing integrity tags with every sector is that
writing the sector and the integrity tag must be atomic - i.e. in case of
crash, either both sector and integrity tag or none of them is written.
To guarantee write atomicity the dm-integrity target uses a journal. It
writes sector data and integrity tags into a journal, commits the journal
and then copies the data and integrity tags to their respective location.
The dm-integrity target can be used with the dm-crypt target - in this
situation the dm-crypt target creates the integrity data and passes them
to the dm-integrity target via bio_integrity_payload attached to the bio.
In this mode, the dm-crypt and dm-integrity targets provide authenticated
disk encryption - if the attacker modifies the encrypted device, an I/O
error is returned instead of random data.
The dm-integrity target can also be used as a standalone target, in this
mode it calculates and verifies the integrity tag internally. In this
mode, the dm-integrity target can be used to detect silent data
corruption on the disk or in the I/O path.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
All reshape I/O share pages from 1st copy device, so just use that pages
for avoiding direct access to bvec table in handle_reshape_read_error.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Now one page array is allocated for each resync bio, and we can
retrieve page from this table directly.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Now we allocate one page array for managing resync pages, instead
of using bio's vec table to do that, and the old way is very hacky
and won't work any more if multipage bvec is enabled.
The introduced cost is that we need to allocate (128 + 16) * copies
bytes per r10_bio, and it is fine because the inflight r10_bio for
resync shouldn't be much, as pointed by Shaohua.
Also bio_reset() in raid10_sync_request() and reshape_request()
are removed because all bios are freshly new now in these functions
and not necessary to reset any more.
This patch can be thought as cleanup too.
Suggested-by: Shaohua Li <shli@kernel.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
reshape read request is a bit special and requires one extra
bio which isn't allocated from r10buf_pool.
Refactor the .bi_end_io for read reshape, so that we can use
raid10's resync page mangement approach easily in the following
patches.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
This patch improve handling of write behind in the following ways:
- introduce behind master bio to hold all write behind pages
- fast clone bios from behind master bio
- avoid to change bvec table directly
- use bio_copy_data() and make code more clean
Suggested-by: Shaohua Li <shli@fb.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The 'offset' local variable can't be changed inside the loop, so
move it out.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Now one page array is allocated for each resync bio, and we can
retrieve page from this table directly.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Christoph Hellwig