It apears that devices designed around Wacom's G11 chipset (e.g. Lenovo
ThinkPad Yoga 260, Lenovo ThinkPad X1 Yoga, Dell XPS 12 9250, Dell Venue
8 Pro 5855, etc.) suffer from a common issue in their HID descriptors.
The logical maximum is not updated for the "Contact Identifier" usage,
leaving it as just "1" despite these devices being capable of tracking
far more touches.
Commit 60a2218698 began ignoring usages with out-of-range values,
causing problems for devices based on this chipset. Touches after
the first will have an out-of-range Contact Identifier, and ignoring
that usage will cause the kernel to incorrectly slot each finger's
events (along with all the knock-on userspace effects that entails).
This commit checks for these buggy descriptors and updates the maximum
where required. Prior chipsets have used "255" as the maximum (and the
G11, at least, doesn't seem to actually use IDs outside the range of
1..CONTACTMAX) so continue using this value.
Cc: stable@vger.kernel.org
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Because HID_DG_TOOLSERIALNUMBER doesn't first cast the value recieved from HID
to an unsigned type, sign-extension rules can cause the value of
wacom_wac->serial[0] to inadvertently wind up with all 32 of its highest bits
set if the highest bit of "value" was set.
This can cause problems for Tablet PC devices which use AES sensors and the
xf86-input-wacom userspace driver. It is not uncommon for AES sensors to send a
serial number of '0' while the pen is entering or leaving proximity. The
xf86-input-wacom driver ignores events with a serial number of '0' since it
cannot match them up to an in-use tool. To ensure the xf86-input-wacom driver
does not ignore the final out-of-proximity event, the kernel does not send
MSC_SERIAL events when the value of wacom_wac->serial[0] is '0'. If the highest
bit of HID_DG_TOOLSERIALNUMBER is set by an in-prox pen which later leaves
proximity and sends a '0' for HID_DG_TOOLSERIALNUMBER, then only the lowest 32
bits of wacom_wac->serial[0] are actually cleared, causing the kernel to send
an MSC_SERIAL event. Since the 'input_event' function takes an 'int' as
argument, only those lowest (now-cleared) 32 bits of wacom_wac->serial[0] are
sent to userspace, causing xf86-input-wacom to ignore the event. If the event
was the final out-of-prox event, then xf86-input-wacom may remain in a state
where it believes the pen is in proximity and refuses to allow other devices
under its control (e.g. the touchscreen) to move the cursor.
It should be noted that EMR devices and devices which use both the
HID_DG_TOOLSERIALNUMBER and WACOM_HID_WD_SERIALHI usages (in that order) would
be immune to this issue. It appears only AES devices are affected.
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These two functions awkwardly break up the otherwise-contiguous chunk of
related Intuos IRQ functions with a 500 line tangent about the operation
of the EKR. Their presence makes it difficult to read/navigate through the
the Intuos code. Since there is no dependency between these functions, it
is possible to simply move them down somewhat. This commit moves them
to be after the final Intuos IRQ function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commits d793ff8 and 4082da8 introduced two pad usages which do not
actually send pad input events. To make sure we do not post empty
pad packets, pad_input_event_flag is introduced. Turn on the flag
for real pad input events so we can synchronize them properly.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 3b164a00a9 ("HID: wacom: Cleanup unsupported device_type
for BAMBOO_PT") cleaned up Bamboo devices which our driver falsely
claimed had touch. Bamboo One Medium also does not have touch.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit f85c9dc ("Support tool ID and additional tool types") introduced mouse
and lens cursor tools to generic codepath, which covers both display (direct)
and opaque tablets (indirect devices). However, mouse and lens cursor tools are
only provided for opaque tablets. This patch ignores mouse and lens cursor tools
if the device is a display tablet.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The features struct for the second gen Intuos Pro uses the wrong constant for
the resolution. This fix is for commit 4922cd2.
Fixes: 4922cd2 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Cintiq Pro has a softkey to turn touch on/off. Since it is
a softkey, hardware/firmware still reports touch events no matter
what state the softkey is. We need to ignore touch events when
the key is in off mode.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Cintiq Pro added a touch key to switch the tablet between
display and opaque mode. This patch informs the change by removing
the old devices and creating new ones with proper properties.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch add support to the 3 touch keys on Wacom Cintiq Pro. These touch
keys are in the middle of the other two keys on the top edge of the tablet.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The prox/range bits included in the Bluetooth reports from the Intuos Pro
were being ignored, leading to two issues. Firstly, the pen would never
announce a BTN_TOOL_PEN event with value 0, leaving userspace to believe
the pen was always active. Secondly, the driver would continue to send
events for data while the packet's "prox" bit was clear. This can lead
to sudden incorrect pointer jumps if the pen is slowly moved away from
the tablet surface.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Non-generic devices have numbered_buttons set for both pen and
touch interfaces by default. The actual number of buttons on the
interface is normally manually decided later, which is different
from what those HID generic devices are processed, where number
of buttons are directly retrieved from HID descriptors.
This patch adds the missed HID_GENERIC check and moves the statement
to wacom_setup_pad_input_capabilities since it's not a quirk anymore.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 025bcc1 performed cleanup work on the 'wacom_pl_irq' function, making
it follow the standards used in the rest of the codebase. The change
unintiontionally allowed the function to send input events from reports
that are not marked as being in prox. This can cause problems as the
report values for X, Y, etc. are not guaranteed to be correct. In
particular, occasionally the tablet will send a report with these values
set to zero. If such a report is received it can caus an unexpected jump
in the XY position.
This patch surrounds more of the processing code with a proximity check,
preventing these zeroed reports from overwriting the current state. To
be safe, only the tool type and ABS_MISC events should be reported when
the pen is marked as being out of prox.
Fixes: 025bcc1540 ("HID: wacom: Simplify 'wacom_pl_irq'")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the LEDs around the mode switch to the generic code path in
support of the second generation Intuos Pro.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The second generation Intuos Pro is the first device in the generic codepath
which has a touchswitch. We utilize a flag in wacom_shared in order to report
this switch event received from the pad on the touch input.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add vendor defined touch to support the second generation Intuos Pro.
Previously all generic Wacom devices used true HID to report their touch.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the touchring to the generic code path in support of the second
generation Intuos Pro.
We also add checks for usage->type to ensure that we handle the usage before we
report it, or change the inrange_state based on it.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Input_event_flag duplicates the information we track in
wacom_wac->hid_data.inrange_state for the pad.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In addition to its USB interface, the second-generation Intuos Pro
includes a Bluetooth radio that offers two pairing interfaces: classic
and low-energy. The classic interface functions just like the earlier
Bluetooth-enabled Intuos4 and Graphire4 tablets, appearing as a HID device
that our driver can work with. The low-energy interface is intented to
be used by userspace applications that make use of its paper-to-digital
capabilities.
Despite the USB interface using Wacom's new vendor-defined HID usages,
the Bluetooth interface provides us with useless black-box "blob"
report descriptors like past devices. We thus have to explicitly add
support for the PIDs and reports used.
These devices pack a /lot/ of information into a single Bluetooth
input report. Each report contains up to seven snapshots of the pen
state, four snapshots of the touch state (of five touches each), pad
state, and battery data. Thankfully this isn't too hard for the driver
to report -- it just takes a fair amount of code to extract!
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There no reason a Bluetooth device with the appropriate HID descriptor couldn't
be used through the HID_GENERIC codepath in the future. Ensure that the driver
attempts to bind to these devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 345857b ("HID: wacom: generic: Add support for sensor offsets") included
a change to the operation and location of the call to 'wacom_add_shared_data'
in 'wacom_parse_and_register'. The modifications included moving it higher up
so that it would occur before the call to 'wacom_retrieve_hid_descriptor'. This
was done to prevent a crash that would have occured when the report containing
tablet offsets was fed into the driver with 'wacom_hid_report_raw_event'
(specifically: the various 'wacom_wac_*_report' functions were written with the
assumption that they would only be called once tablet setup had completed;
'wacom_wac_pen_report' in particular dereferences 'shared' which wasn't yet
allocated).
Moving the call to 'wacom_add_shared_data' effectively prevented the crash but
also broke the sibiling detection code which assumes that the HID descriptor
has been read and the various device_type flags set.
To fix this situation, we restore the original 'wacom_add_shared_data'
operation and location and instead implement an alternative change that can
also prevent the crash. Specifically, we notice that the report functions
mentioned above expect to be called only for input reports. By adding a check,
we can prevent feature reports (such as the offset report) from
causing trouble.
Fixes: 345857bb49 ("HID: wacom: generic: Add support for sensor offsets")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
post input_sync only when there are input events posted
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-By: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make sure everything reported from pad are registered
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-By: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sometime valid events may not be supported by the driver yet. Make
sure we don't process them when the code is not ready.
This fix prevents a kernel panic due to unsupported HID events.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-By: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is unnecessary to return a value since nothing is expecting a
value from it.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-By: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The eraser end of the 8K pen available for the MobileStudio Pro has a tool
ID of 0x84a. The 'wacom_intuos_get_tool_type' function does not currently
recognize this ID, causing it to return BTN_TOOL_PEN rather than
BTN_TOOL_RUBBER. This does not cause a problem for the MobileStudio Pro
since, as a HID_GENERIC device, the driver relies on the state of the
HID_DG_INVERT usage instead. It would, however, cause problems if the pen
is used with devices that use the traditional 'wacom_intuos_irq' codepath
instead.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is trying to clear the lower 32 bits but the type is wrong so it
clears everything.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID specification that the MobileStudio Pro follows includes usages
for several values that would be good to support so that future devices
"just work" out of the box. Extend the HID_GENERIC pad codepath to handle
these usages.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for usages that may appear on the pen or pad interface which
report the state of the tablet battery.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As with usages for the pen, the Custom HID specificiation includes
usages for the pad. Here we add functions to map and handle most
of the pad usages present on the MobileStudio Pro.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many of Wacom's display tablets include an "outbound" area where pen
digitizing is possible but outside of the display area. To accommodate
such sensors in the HID_GENERIC codepath, we add support for the
necessary vendor-defined HID feature usages and adjust the min/max
values of the X and Y axes accordingly, similar to what is done in
the non-generic codepath.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many of Wacom's display tablets include an "outbound" area where pen
digitizing is possible but outside of the display area. To ensure that
pen coordinates are mapped to the correct on-screen location, the driver
sets the minimum and maximum axis values of X and Y to those coordinates
which coincide with the screen edge. These values are simply the
hardware minimum/maximum plus/minus the outbound size for a particular
edge.
When outbound support was added/updated in ac414da, fa77034, and
ecd618d, we decided to have the wacom_features structs store the desired
minimum and maximum values directly. In hindsight, this was perhaps not
the best choice since it has allowed minor errors to crop up unnoticed.
Some tablets have had their coordinates over-corrected (e.g. most of the
devices "fixed" in ecd618d were already adjusted in ac414da), while
others never had a correction applied (e.g. the ISDv5 325, whose
declared maximum the hardware maximum instead of the outbound maximum).
A less error-prone method of handling the outbound is to let the driver
calculate the correct minimum/maximum values by providing it with both
the actual hardware maximums and the size of the outbound on each edge.
These values are more easy to verify as correct since the values can be
trivially compared against specifications.
This patch reverts the declared maximum values to the actual hardware
maximums, e.g. as declared prior to ac414da (values for these and other
display tablets that were subsuquently introduced have been verified
against specs). Per-edge outbound sizes are stored in the wacom_features
struct as offset_{left,right,top,bottom} and used in combination with
the hardware ranges to calculate effective axis ranges for ABS_X and
ABS_Y.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices following the new Custom HID mode specification (as well as even
some recent component sensors which use the same standard HID usage)
are capable of reporting tool ID information that we need to relay to
userspace. This patch adds support for reading and relaying the tool
type information, which is (unfortunately) split across two usages.
We also advertise the existence of tool types beyond BTN_TOOL_PEN
that might be available.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'wacom_intuos_inout' function incorrectly assmebles tool IDs from the
proximity report, shifting the higher values of the ID four bits farther
than intended. This problem was not detected until too late, but has not
caused any issues since the incorrect IDs still fit in a 32-bit integer
and userspace programs have not required the value to match the hardware
(just that the values are unique and constant).
The tool IDs reported by the new MobileStudio Pro (or any future
HID_GENERIC device that supports them) do not suffer from the same
assembly issue, however. In order for 'wacom_intuos_get_tool_type' to
work for with both codepaths, we correct this issue internally and
have 'wacom_intuos_general' only mangle the ID when it is posted to
userspace.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom's professional tablets beginning with the Intuos4 are capable of
reporting an intermediate degree of proximity where the pen is no longer
close enough to communicate with ("in prox"), but still close enough to
be sensed ("in range"). This additional state is particularly useful for
performing palm rejection as it allows the driver to disable the touch
sensor while the pen is a greater distance from the tablet.
Like other professional tablets, the new MobileStudio Pro also reports
this intermeidate "in range" proximity state. Its descriptor assigns
usage 0xff0d0036 to this bit. Normally 'wacom_equivalent_usage' would
translate this to the standard HID "Quality" usage, but since this has
a different meaning we have it explicitly ignore the usage and define
it ourselves as "Sense" (since "In Range" is already defined by the
HID standard and interpreted by our driver as meaning "in prox").
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The airbrush fingerwheel does not have a usage that corresponds cleanly
with a standard HID usage, so we add explicit support for it via its
vendor-defined usage.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The vendor-defined 0xFF0D01032 ("Distance") usage is nearly equivalent to
HID_GD_Z, except that the axis direction is inverted. Unlike HID_GD_Z which
increases in value as the pen-to-surface distance is decreased, this usage
decreases. Treat this usage as a special case to ensure we don't invert the
scale to be ABS_DISTANCE compatible like we do for HID_GD_Z.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom's new "MobileStudio Pro" tablets are the first devices in their
branded product line-up to include a usable HID descriptor for the pen
interface. Like prior branded products, the device can operate in one
of two modes: 'Standard HID', and 'Wacom Custom HID'. Although the
first mode is usable by the HID_GENERIC codepath as-is (huzzah!), it is
subject to some restrictions -- most notably pressure being limited
to 2048 levels instead of 8192. To ensure tablets that include support
for Custom HID mode work optimally, we add support for its usages and
switch the device to Custom HID mode if possible.
The usages defined for Custom HID mode are often numerically similar to
their standard HID equivalents, allowing us to write a simple translation
function that takes arbitrary HID usages as input and which returns
the corresponding standard HID usage as output (if one exists). Switching
on this translated usage instead of the actual usage allows the existing
cases to apply to both modes of operation without having to explicitly
define every Custom HID usage.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID standard defines usages that allow digitizers to report the pen's
height, tilt, and rotation and which are used by Wacom's new "MobileStudio
Pro" devices.
Note that 'hidinput_calc_abs_res' expects ABS_Z (historically used by our
driver to report twist) to have linear units. To ensure it calculates a
resolution with the actually-angular units provided in the HID descriptor
we nedd to lie and tell it we're calculating it for the (rotational) ABS_RZ
axis instead.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This just centralizes the logic used in both wacom_setup_numbered_buttons
and wacom_report_numbered_buttons so that they don't drift out of sync.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Our loose use of "pen" and "digitizer" in the naming of several of our
vendor-defined usages may be a source of confusion given that the terms
have specific meaning within the HID specification. "Pen" specifically
refers to "an integrated display that allows the use of a stylus" (e.g.
something like a tablet PC or Cintiq) wheras "Digitizer" is a better
fit for opaque tablets like an Intuos.
While we're at it, go ahead and rename the definitions to make them more
distinct and better match up with the convention used by HID (e.g. the use
of '_UP_' for usage pages) and make them more distinct.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a touchscreen contains both multitouch and single-touch reports in its
descriptor in that order, the driver may overwrite information it saved
about the format of the multitouch report. This can cause the report
processing code to get tripped up and send an incorrect event stream to
userspace.
In particular, this can cause last_slot_field to be overwritten with the
result that the driver prematurely assumes it has finished processing a
slot and sending the ABS_MT_SLOT event at the wrong point in time,
associating events for the current contact with the following contact
instead.
To prevent this from occurring, we update the value of last_slot_field
durring the pre_report phase to ensure that it is correct for the report
that is to be processed.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Touch arbitration is always on in wacom.ko. However, there are
touch enabled applications use both pen and touch simultaneously.
We should provide an option for userland to decide if they want
arbitration on or off.
This patch sets default touch_arbitration to on since most userland
apps are not ready to process pen and touch events simultaneously.
In the future, when userland is ready to accept pen and touch events
together, we will switch default touch_arbitration to off.
Tested-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'oVid' and 'oPid' variables used by wacom_are_sibling are a hacky
solution to the problem of the driver historically having few good
heuristics to use in determining if two devices should be considered
siblings or not. While it works well enough for explicitly supported
devices, it offers no help for HID_GENERIC devices. Now that we have
a bit more information (e.g. direct/indirect) available to us though,
we should make use of it it to improve the pairing of such devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
"Direct" input devices like Cintiqs and Tablet PCs set the INPUT_PROP_DIRECT
property to notify userspace that the sensor and screen are overlaid. This
information can also be useful elsewhere within the kernel driver, however,
so we introduce a new WACOM_DEVICETYPE_DIRECT that signals this to other
kernel code.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 24HD has 1 button per LED (first three buttons of each group).
We need a special treatment for them as it's not a uniq button that
switches between the LEDs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The code for 21UX2 and 24HD makes the LED group 1 on the left, and
the group 0 on the right. The buttons are ordered in the other way,
but libwacom already exports those that way. So we simply can't reassign
LED group 0 to the left buttons, and have to quirk the incoming data...
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina