Implement set/get functions to configure PFC stall prevention
timeout by tunables api through ethtool.
By default the stall prevention timeout is configured to 8 sec.
Timeout range is: 80-8000 msec.
Enabling stall prevention with the auto timeout will set
the timeout to 100 msec.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The QPTS register allows changing the priority trust state between pcp and
dscp. Add support to get/set trust state from device. When the port is
in pcp/dscp trust state, packet is routed by hardware to matching priority
based on its pcp/dscp value respectively.
The QPDPM register allow channing the dscp to priority mapping. Add support
to get/set dscp to priority mapping from device.
Note that to change a dscp mapping, the "e" bit of this dscp structure
must be set in the QPDPM firmware command.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Previously, tc with ets type and zero bandwidth is not accepted
by driver. This behavior does not follow the IEEE802.1qaz spec.
If there are tcs with ets type and zero bandwidth, these tcs are
assigned to the lowest priority tc_group #0. We equally distribute
100% bw of the tc_group #0 to these zero bandwidth ets tcs.
Also, the non zero bandwidth ets tcs are assigned to tc_group #1.
If there is no zero bandwidth ets tc, the non zero bandwidth ets tcs
are assigned to tc_group #0.
Fixes: cdcf11212b ("net/mlx5e: Validate BW weight values of ETS")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Read port connector type from the firmware instead of caching it in the
driver metadata.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add set/query commands for DCBX_PARAM register
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DCBX CEE API interface for ConnectX-4. Configurations are stored in
a temporary structure and are applied to the card's firmware when
the CEE's setall callback function is called.
Note:
priority group in CEE is equivalent to traffic class in ConnectX-4
hardware spec.
bw allocation per priority in CEE is not supported because ConnectX-4
only supports bw allocation per traffic class.
user priority in CEE does not have an equivalent term in ConnectX-4.
Therefore, user priority to priority mapping in CEE is not supported.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hardware structures and constants definitions needed for module
events support.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced mlx5_query_port_proto_oper with separate functions per link
type. The functions should take different arguments so no point in
trying to unite them.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The mlx5e_link_mode enumeration will also be used in mlx5_ib for RoCE.
This patch moves the enumeration to the mlx5 driver port header file.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Previous to this patch auto negotiation was reported off although it was
on by default in hardware. This patch reports the correct information to
ethtool and allows the user to toggle it on/off.
Added another parameter to set port proto function in order to pass
the auto negotiation field to the hardware.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dedicated function to toggle port link. It should be called only
after setting a port register.
Toggle will set port link to down and bring it back up in case that it's
admin status was up.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in the conflicts.
In the macsec case, the change of the default ID macro
name overlapped with the 64-bit netlink attribute alignment
fixes in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add query MCIA, PMLP registers infrastructure and commands.
Add ethtool support for get_module_info() and get_module_eeprom()
callbacks.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the needed hardware command and mlx5_ifc structs for managing LED
control.
Add set_phys_id ethtool callback to support ethtool -p flag.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new access register named Ports Check Mask Register (PCMR) to
control all HW checks on port. With this register, the driver can
enable/disable Hardware FCS validation.
When RXALL is enabled/disabled using ndo_set_features, enable/disable
fcs check at HW.
User can change HW configuration using rx-all flag at ethtool.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For set/query MTU port firmware commands the MTU field
is 16 bits, here I changed all the "int mtu" parameters
of the functions wrapping those firmware commands to be u16.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set/get WOL by ethtool and added the needed
device commands and structures to mlx5_ifc.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DCBNL IEEE get/set max rate.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access functions to set and query a physical port TC groups
and prio parameters.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access functions to set and query a physical port PFC
(Priority Flow Control) parameters.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the device physical port access functions are implemented in the
port.c file.
We just extract the exposure of these functions from driver.h into a
dedicated header file called port.h.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inbar Karmy