This patch provides a basic support for USB MIDI 2.0. As of this
patch, the driver creates a UMP device per MIDI I/O endpoints, which
serves as a dumb terminal to read/write UMP streams.
A new Kconfig CONFIG_SND_USB_AUDIO_MIDI_V2 manages whether to enable
or disable the MIDI 2.0 support. Also, the driver provides a new
module option, midi2_enable, to allow disabling the MIDI 2.0 at
runtime, too. When MIDI 2.0 support is disabled, the driver tries to
fall back to the already existing MIDI 1.0 device (each MIDI 2.0
device is supposed to provide the MIDI 1.0 interface at the altset
0).
For now, the driver doesn't manage any MIDI-CI or other protocol
setups by itself, but relies on the default protocol given via the
group terminal block descriptors.
The MIDI 1.0 messages on MIDI 2.0 device will be automatically
converted in ALSA sequencer in a later patch. As of this commit, the
driver accepts merely the rawmidi UMP accesses.
The driver builds up the topology in the following way:
- Create an object for each MIDI endpoint belonging to the USB
interface
- Find MIDI EP "pairs" that share the same GTB;
note that MIDI EP is unidirectional, while UMP is (normally)
bidirectional, so two MIDI EPs can form a single UMP EP
- A UMP endpoint object is created for each I/O pair
- For remaining "solo" MIDI EPs, create unidirectional UMP EPs
- Finally, parse GTBs and fill the protocol bits on each UMP
So the driver may support multiple UMP Endpoints in theory, although
most devices are supposed to have a single UMP EP that can contain up
to 16 groups -- which should be large enough.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We're going to create rawmidi objects for MIDI 2.0 in a different code
from the current code for USB-MIDI 1.0. As a preliminary work, this
patch adds the number of rawmidi objects to keep globally in a
USB-audio card instance, so that it can be referred from both MIDI 1.0
and 2.0 code.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an error occurs during USB disconnection sometimes things can go
wrong as endpoint_set_interface may end up being called repeatedly. For
example:
% dmesg --notime | grep 'usb 3-7.1.4' | sort | uniq -c | head -2
3069 usb 3-7.1.4: 1:1: usb_set_interface failed (-19)
908 usb 3-7.1.4: 1:1: usb_set_interface failed (-71)
In my case, there sometimes are hundreds of these usb_set_interface
failure messages a second when I disconnect the hub that has my USB
audio device.
These messages can take a huge amount of the kmsg ringbuffer and don't
provide any extra information over the previous ones, so ratelimit them.
Signed-off-by: Chris Down <chris@chrisdown.name>
Link: https://lore.kernel.org/r/ZEKf8UYBYa1h4JWR@chrisdown.name
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that the firmware is broken and does not accept
the UAC_EP_CS_ATTR_SAMPLE_RATE URB. There is only one rate (48000Hz)
available in the descriptors for the output endpoint.
Create a new quirk QUIRK_FLAG_FIXED_RATE to skip the rate setup
when only one rate is available (fixed).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216798
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20221215153037.1163786-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tascam's Model 12 is a mixer which can also operate as a USB audio
interface. The audio interface uses explicit feedback but it seems that
it does not correctly handle missing isochronous frames.
When injecting an xrun (or doing anything else that pauses the playback
stream) the feedback rate climbs (for example, at 44,100Hz nominal, I
see a stable rate around 44,099 but xrun injection sees this peak at
around 44,135 in most cases) and glitches are heard in the audio stream
for several seconds - this is significantly worse than the single glitch
expected for an underrun.
While the stream does normally recover and the feedback rate returns to
a stable value, I have seen some occurrences where this does not happen
and the rate continues to increase while no audio is heard from the
output. I have not found a solid reproduction for this.
This misbehaviour can be avoided by totally resetting the stream state
by switching the interface to alt 0 and back before restarting the
playback stream.
Add a new quirk flag which forces the endpoint and interface to be
reconfigured whenever the stream is stopped, and use this for the Tascam
Model 12.
Separate interfaces are used for the playback and capture endpoints, so
resetting the playback interface here will not affect the capture stream
if it is running. While there are two endpoints on the interface,
these are the OUT data endpoint and the IN explicit feedback endpoint
corresponding to it and these are always stopped and started together.
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20221129130100.1257904-1-john@metanate.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Hamedal C20, the current rate is different from the runtime rate,
snd_usb_endpoint stop and close endpoint to resetting rate.
if snd_usb_endpoint close the endpoint, sometimes usb will
disconnect the device.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Link: https://lore.kernel.org/r/20221110063452.295110-1-aichao@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The USB-audio driver matches per interface, and as default, it
registers the card instance at the very first instance. This can be a
problem for the devices that have multiple interfaces to be probed, as
the udev rule isn't applied properly for the later appearing
interfaces. Although we introduced the delayed_register option and
the quirks for covering those shortcomings, it's nothing but a
workaround for specific devices.
This patch is an another attempt to fix the problem in a more generic
way. Now the driver checks the whole USB device descriptor at the
very first time when an interface is attached to a sound card. It
looks at each matching interface in the descriptor and remembers the
last matching one. The snd_card_register() is invoked only when this
last interface is probed.
After this change, the quirks for the delayed registration become
superfluous, hence they are removed along with the patch. OTOH, the
delayed_register option is still kept, as it might be useful for some
corner cases (e.g. a special driver overtakes the interface probe from
the standard driver, and the last interface probe may miss).
Link: https://lore.kernel.org/r/20220904161247.16461-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a clock source is connected to multiple nodes / endpoints, the
current USB-audio driver tries to set up at each time one of them is
configured. Although it reads the current rate and updates only if it
differs, some devices seem unhappy with this behavior and spew the
errors when reading/updating the rate unnecessarily.
This patch tries to reduce the redundant clock setup by introducing a
refcount for each clock source. When the stream is actually running,
a clock rate is "locked", and it bypasses the clock and/or refuse to
change any longer.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215934
Link: https://lore.kernel.org/r/20220516104807.16482-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For making easier to test, add the new quirk_flags bits 17 and 18 to
enable and disable the generic implicit feedback mode. The bit 17 is
equivalent with implicit_fb=1 option, applying the generic implicit
feedback sync mode. OTOH, the bit 18 disables the implicit fb mode
forcibly.
Link: https://lore.kernel.org/r/20220421064101.12456-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix:
sound/usb/midi.c: In function ‘snd_usbmidi_out_endpoint_create’:
sound/usb/midi.c:1389:2: error: case label does not reduce to an integer constant
case USB_ID(0xfc08, 0x0101): /* Unknown vendor Cable */
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
[ A slight correction with parentheses around the argument by tiwai ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220405151517.29753-3-bp@alien8.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For making user to switch back to the old playback mode, this patch
adds a new module option 'lowlatency' to snd-usb-audio driver.
When user face a regression due to the recent low-latency playback
support, they can test easily by passing lowlatency=0 option without
rebuilding the kernel.
Fixes: 307cc9baac ("ALSA: usb-audio: Reduce latency at playback start, take#2")
Link: https://lore.kernel.org/r/20210829073830.22686-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent quirk for WALKMAN (commit 7af5a14371c1: "ALSA: usb-audio:
Fix regression on Sony WALKMAN NW-A45 DAC") may be required for other
devices and is worth to be put into the common quirk flags.
This patch adds a new quirk flag bit QUIRK_FLAG_SET_IFACE_FIRST and a
quirk table entry for the device.
Link: https://lore.kernel.org/r/20210824055720.9240-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixer code has a flag ignore_ctl_error for ignoring the errors
returned from the device wrt mixer accesses, and this is set from the
entries in mixer_maps.c, as well as ignore_ctl_error module option.
Those can be well integrated into the new quirk_flags field, too.
Link: https://lore.kernel.org/r/20210729074404.19728-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The auto-suspend suppression workaround for Lenovo machines are
handled in quirks-table.h. Now it's more easier to handle with
quirk_flags.
Link: https://lore.kernel.org/r/20210729074404.19728-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The rate validation at the device probe is applied only to the
specific devices (currently only for MOTU devices), and this check can
be moved to quirk_flags gracefully, too.
Link: https://lore.kernel.org/r/20210729074404.19728-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We apply some delay for the control messages on certain devices as a
workaround, and this can be moved into the quirk_flags as well.
Currently there are three different delay periods (1ms, 5ms and 20ms),
so three different quirk bits are assigned for them.
Link: https://lore.kernel.org/r/20210729073855.19043-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is another quirk for the transfer, and that's currently specific
to Zoom R16/24, handled in create_standard_audio_quirk(). Let's move
this also to the new quirk_flags.
Link: https://lore.kernel.org/r/20210729073855.19043-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The txfr_quirk field was meant for aligning the transfer, and it's set
for certain devices in quirks-table.h. Now we can move that stuff
also to the new quirk_flags gracefully, and reduce the quirks-table.h
entries (that are exposed to module device table).
As the quirks-table.h entries are also with the name string override,
provide the corresponding entries to the usb_audio_names[] table,
too.
Link: https://lore.kernel.org/r/20210729073855.19043-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The devices that can have media-controller API entries are currently
specified via tables in quirks-table.h, as a part of descriptor
override. This can fit better to the new quirk_flags, as we just need
a matching with the given ID and create the MC entries accordingly.
Link: https://lore.kernel.org/r/20210729073855.19043-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As more and more device-specific workarounds came up and gathered in
various places, it becomes harder to manage. Now it's time to clean
up and collect workarounds more consistently and make them more easily
applicable.
This patch is the first step for that: a new field quirk_flags is
introduced in snd_usb_audio struct to contain the bit flags for
various device-specific quirks. Those are separate one from the
quirks in quirks-table.h; the quirks-table.h entries are for more
intrusive stuff that needs the descriptor override, while the new
quirk_flags is for easier ones that are tied with the vendor:product
IDs.
In this patch, as the first example, we convert the list of devices
and vendors to ignore GET_SAMPLE_RATE, formerly defined in
snb_usb_get_sample_rate_quirk().
Link: https://lore.kernel.org/r/20210729073855.19043-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During the recent rewrite of the implicit feedback support, we've
tested to apply the implicit fb on BOSS devices, but it failed, as the
capture stream didn't start without the playback. As the end result,
it got another type of quirk for tying both streams but starts
playback always (commit 6234fdc1ce "ALSA: usb-audio: Quirk for BOSS
GT-001").
Meanwhile, Mike Oliphant has tested the real implicit feedback mode
for the playback again with the latest code, and found out that it
actually works if the initial feedback sync is skipped; that is, on
those BOSS devices, the playback stream has to be started at first
without waiting for the capture URB completions. Otherwise it gets
stuck. In the rest operations after the capture stream processed, we
can take them as the implicit feedback source.
This patch is an attempt to improve the support for BOSS devices with
the implicit feedback mode in the way described above. It adds a new
flag to snd_usb_audio, playback_first, indicating that the playback
stream starts without sync with the initial capture completion. This
flag is set in the quirk table with the new IMPLICIT_FB_BOTH type.
Reported-and-tested-by: Mike Oliphant <oliphant@nostatic.org>
Link: https://lore.kernel.org/r/20210414083255.9527-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
UA-101 device and co are supported by another driver, snd-ua101, but
the USB audio class driver (snd-usb-audio) catches all and this
resulted in the lack of functionality like missing MIDI devices.
This patch introduces a sort of deny-listing for those devices to just
return -ENODEV at probe in snd-usb-audio driver, so that it falls back
to the probe by snd-ua101.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212477
Link: https://lore.kernel.org/r/20210408075656.30184-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few calls of usb_driver_claim_interface() but all of those
miss the proper error checks, as reported by Coverity. This patch
adds those missing checks.
Along with it, replace the magic pointer with -1 with a constant
USB_AUDIO_IFACE_UNUSED for better readability.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1475943 ("Error handling issues")
Addresses-Coverity-ID: 1475944 ("Error handling issues")
Addresses-Coverity-ID: 1475945 ("Error handling issues")
Fixes: b1ce7ba619 ("ALSA: usb-audio: claim autodetected PCM interfaces all at once")
Fixes: e5779998bf ("ALSA: usb-audio: refactor code")
Link: https://lore.kernel.org/r/202104051059.FB7F3016@keescook
Link: https://lore.kernel.org/r/20210406113534.30455-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rear audio on Lenovo ThinkStation P620 stops working after commit
1965c4364b ("ALSA: usb-audio: Disable autosuspend for Lenovo
ThinkStation P620"):
[ 6.013526] usbcore: registered new interface driver snd-usb-audio
[ 6.023064] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023083] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.023090] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023098] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.023103] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023110] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045846] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045866] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045877] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045886] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045894] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045908] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
I overlooked the issue because when I was working on the said commit,
only the front audio is tested. Apology for that.
Changing supports_autosuspend in driver is too late for disabling
autosuspend, because it was already used by USB probe routine, so it can
break the balance on the following code that depends on
supports_autosuspend.
Fix it by using usb_disable_autosuspend() helper, and balance the
suspend count in disconnect callback.
Fixes: 1965c4364b ("ALSA: usb-audio: Disable autosuspend for Lenovo ThinkStation P620")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304043419.287191-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current endpoint handling assumed (more or less) a unique 1:1
relation between the endpoint and the iface/altset. The exception was
the sync EP without the implicit feedback which has usually the
secondary EP of the same altset. This works fine for most devices,
but it turned out that some unusual devices like Pinoeer's ones have
both playback and capture endpoints in the same iface/altsetting and
use both for the implicit feedback mode. For handling such a case, we
need to extend the endpoint management to take the shared interface
into account.
This patch does that: it adds a new object snd_usb_iface_ref for
managing the reference counts of the each USB interface that is used
by each endpoint. The interface setup is performed only once for the
(sharing) endpoints, and the doubly initialization is avoided.
Along with this, the resource release of endpoints and interface
refcounts are put into a single function, snd_usb_endpoint_free_all()
instead of looping in the caller side.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/20210108075219.21463-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A new module option, implicit_fb, is added to specify the driver
looking for the implicit feedback sync. This can be useful for a
device that could be working better in the implicit feed back mode and
user wants to test it quickly. When this works, we can add the quirk
entry easily.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-40-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 92adc96f8e ("ALSA: usb-audio: set the interface format
after resume on Dell WD19") introduced the workaround for the broken
setup after the resume specifically on a Dell dock model. However,
the full setup should have been performed after the resume on all
devices, as we can't guarantee the same state. So this patch removes
the conditional check and applies the workaround always.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-24-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This behavior turned out to be invalid from the USB spec POV and
shouldn't be applied. As it's an optional flag that is set only via
an card control element that must be hardly used, let's drop it
again.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-16-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct quirk table entries for Lenovo ThinkStation P620, too.
The name and profile strings are now set from a different table, hence
removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If USB autosuspend is enabled, both front and rear panel can no longer
detect jack insertion.
Enable USB remote wakeup, i.e. needs_remote_wakeup = 1, doesn't help
either.
So disable USB autosuspend to prevent missing jack detection event.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20200823105854.26950-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far we've added the devices that need vendor/product string renames
or the profile setup into the standard quirk table in quirks-table.h.
This table is imported into the primary USB audio device entry, hence
it's all exported for the probing so that udev and co can take a look
at it. OTOH, for renaming or profile setup, we don't need to expose
those explicit entries because the probe itself follows the standard
way. That said, we're exposing unnecessarily too many entries.
This patch moves such internal quirk entries into the own table, and
reduces the exported device table size. Along with the moving items,
re-arrange the entries in the proper order.
Link: https://lore.kernel.org/r/20200817082140.20232-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently USB-audio driver manages the auto-pm of the primary
interface although a card may consist of multiple interfaces.
This may leave the secondary and other interfaces left running
unnecessarily after the auto-suspend.
This patch allows the driver managing the auto-pm of all bundled
interfaces per card. The chip->pm_intf field is extended as
chip->intf[] to contain the array of assigned interfaces, and the
runtime-PM is performed to all those interfaces.
Tested-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20200605064117.28504-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a USB-audio interface gets runtime-suspended via auto-pm feature,
the driver suspends all functionality and increment
chip->num_suspended_intf. Later on, when the system gets suspended to
S3, the driver increments chip->num_suspended_intf again, skips the
device changes, and sets the card power state to
SNDRV_CTL_POWER_D3hot. In return, when the system gets resumed from
S3, the resume callback decrements chip->num_suspended_intf. Since
this refcount is still not zero (it's been runtime-suspended), the
whole resume is skipped. But there is a small pitfall here.
The problem is that the driver doesn't restore the card power state
after this resume call, leaving it as SNDRV_CTL_POWER_D3hot. So,
even after the system resume finishes, the card instance still appears
as if it were system-suspended, and this confuses many ioctl accesses
that are blocked unexpectedly.
In details, we have two issues behind the scene: one is that the card
power state is changed only when the refcount becomes zero, and
another is that the prior auto-suspend check is kept in a boolean
flag. Although the latter problem is almost negligible since the
auto-pm feature is imposed only on the primary interface, but this can
be a potential problem on the devices with multiple interfaces.
This patch addresses those issues by the following:
- Replace chip->autosuspended boolean flag with chip->system_suspend
counter
- At the first system-suspend, chip->num_suspended_intf is recorded to
chip->system_suspend
- At system-resume, the card power state is restored when the
chip->num_suspended_intf refcount reaches to chip->system_suspend,
i.e. the state returns to the auto-suspended
Also, the patch fixes yet another hidden problem by the code
refactoring along with the fixes above: namely, when some resume
procedure failed, the driver left chip->num_suspended_intf that was
already decreased, and it might lead to the refcount unbalance.
In the new code, the refcount decrement is done after the whole resume
procedure, and the problem is avoided as well.
Fixes: 0662292aec ("ALSA: usb-audio: Handle normal and auto-suspend equally")
Reported-and-tested-by: Macpaul Lin <macpaul.lin@mediatek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200603153709.6293-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The USB-audio driver may call snd_card_register() multiple times as
its probe function is per USB interface while some USB-audio devices
may provide multiple interfaces to assign different streams although
they belong to the same device. This works in most cases but the
registration is racy, hence it may miss the device recognition,
e.g. PA doesn't see certain devices when hotplugged.
The recent addition of the delayed registration quirk allows to sync
the registration at the last known interface, and the previous commit
added a new module option to allow the dynamic setup for that
purpose.
Now, this patch tries to find out and notifies for such devices that
require the delayed registration. It shows a message like:
Found post-registration device assignment: 1234abcd:02
If you hit this message, you can pass delayed_register module option
like:
snd_usb_audio.delayed_register=1234abcd:02
by just copying the last shown entry. If this works, it can be added
statically in the quirk list, registration_quirks[] found at the end
of sound/usb/quirks.c.
Link: https://lore.kernel.org/r/20200325103322.2508-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we found the headset-mic on the Dell Dock WD19 doesn't work
anymore after s3 (s2i or deep), this problem could be workarounded by
closing (pcm_close) the app and then reopening (pcm_open) the app, so
this bug is not easy to be detected by users.
When problem happens, retire_capture_urb() could still be called
periodically, but the size of captured data is always 0, it could be
a firmware bug on the dock. Anyway I found after resuming, the
snd_usb_pcm_prepare() will be called, and if we forcibly run
set_format() to set the interface and its endpoint, the capture
size will be normal again. This problem and workaound also apply to
playback.
To fix it in the kernel, add a quirk to let set_format() run
forcibly once after resume.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191218132650.6303-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The unit descriptor validation may lead to a probe error when the
device provides a buggy descriptor or the validator detected
incorrectly. For identifying such an error and band-aiding, give a
new module option, skip_validation. With this option, the driver
ignores the validation errors with the hexdump of the unit
descriptor, so we can check it in a bit more details.
Link: https://lore.kernel.org/r/20191114165613.7422-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Media Device Allocator API to allows multiple drivers share a media device.
This API solves a very common use-case for media devices where one physical
device (an USB stick) provides both audio and video. When such media device
exposes a standard USB Audio class, a proprietary Video class, two or more
independent drivers will share a single physical USB bridge. In such cases,
it is necessary to coordinate access to the shared resource.
Using this API, drivers can allocate a media device with the shared struct
device as the key. Once the media device is allocated by a driver, other
drivers can get a reference to it. The media device is released when all
the references are released.
Change the ALSA driver to use the Media Controller API to share media
resources with DVB, and V4L2 drivers on a AU0828 media device.
The Media Controller specific initialization is done after sound card is
registered. ALSA creates Media interface and entity function graph nodes
for Control, Mixer, PCM Playback, and PCM Capture devices.
snd_usb_hw_params() will call Media Controller enable source handler
interface to request the media resource. If resource request is granted,
it will release it from snd_usb_hw_free(). If resource is busy, -EBUSY is
returned.
Media specific cleanup is done in usb_audio_disconnect().
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, USB-audio driver allocates the PCM buffer via vmalloc(), as
this serves merely as an intermediate buffer that is copied to each
URB transfer buffer. This works well in general on x86, but on some
archs this may result in cache coherency issues when mmap is used.
OTOH, it works also on such arch unless mmap is used.
This patch is a step for mitigating the inconvenience; a new module
option "use_vmalloc" is provided so that user can choose to allocate
the DMA coherent buffer instead of the existing vmalloc buffer.
The drawback is that it'd be the standard dma_alloc_coherent() calls
and the system would require contiguous pages on non-x86 archs.
Note that it's a global option and not dynamically switchable since
the buffer is pre-allocated at the probe time. In theory, it's
possible to be switchable, but it'd be trickier and racier.
As default use_vmalloc option is set to true, so that the old behavior
is kept. For allowing the coherent mmap on ARM or MIPS, pass
use_vmalloc=0 option explicitly.
Reported-and-tested-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently released USB Audio Class 3.0 specification
contains BADD (Basic Audio Device Definition) document
which describes pre-defined UAC3 configurations.
BADD support is mandatory for UAC3 devices, it should be
implemented as a separate USB device configuration.
As per BADD document, class-specific descriptors
shall not be included in the Device’s Configuration
descriptor ("inferred"), but host can guess them
from BADD profile number, number of endpoints and
their max packed sizes.
This patch adds support of all BADD profiles from the spec
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Tested-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Historically USB-audio driver sets the card's longname field with the
details of the device and the bus information. It's good per se, but
not preferable when it's referred as the identifier for UCM profile.
This patch adds a quirk profile_name field to override the card's
longname string to a pre-defined one, so that one can create a unique
and consistent ID string for the specific USB device via a quirk table
to be used as a UCM profile name.
The patch does a slight code refactoring to split out the functions to
set shortname and longname fields as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce a new flag to struct snd_usb_audio for allowing the device
to skip usb_set_interface() calls at changing or closing the stream.
As of this patch, the flag is nowhere set, so it's just a place
holder. The dynamic switching will be added in the following patch.
A background information for this change:
Dell WD15 dock with Realtek chip gives a very long pause at each time
the driver changes the altset, which eventually happens at every PCM
stream open/close and parameter change. As the long pause happens in
each usb_set_interface() call, there is nothing we can do as long as
it's called. The workaround is to reduce calling it as much as
possible, and this flag indicates that behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are many USB audio devices with buggy firmware that don't react
with the sample rate reading properly. This often results in the
flood of error messages and slowing down the operation.
The sample rate read back is basically only for confirming the sample
rate setup, and it's not critically important. As a compromise, in
this patch, we stop the sample rate read back once when the device
gives errors more than tolerance (twice, as of now). This should
improve most of error cases while we still can catch the firmware
bugginess.
Signed-off-by: Takashi Iwai <tiwai@suse.de>