This patch adds a new device-tree property that allows to
specify the dma protection control bits for the all of the
DMA controller's channel uniformly.
Setting the "correct" bits can have a huge impact on the
PPC460EX and APM82181 that use this DMA engine in combination
with a DesignWare' SATA-II core (sata_dwc_460ex driver).
In the OpenWrt Forum, the user takimata reported that:
|It seems your patch unleashed the full power of the SATA port.
|Where I was previously hitting a really hard limit at around
|82 MB/s for reading and 27 MB/s for writing, I am now getting this:
|
|root@OpenWrt:/mnt# time dd if=/dev/zero of=tempfile bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 13.65s
|user 0m 0.01s
|sys 0m 11.89s
|
|root@OpenWrt:/mnt# time dd if=tempfile of=/dev/null bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 8.41s
|user 0m 0.01s
|sys 0m 4.70s
|
|This means: 121 MB/s reading and 75 MB/s writing!
|
|The drive is a WD Green WD10EARX taken from an older MBL Single.
|I repeated the test a few times with even larger files to rule out
|any caching, I'm still seeing the same great performance. OpenWrt is
|now completely on par with the original MBL firmware's performance.
Another user And.short reported:
|I can report that your fix worked! Boots up fine with two
|drives even with more partitions, and no more reboot on
|concurrent disk access!
A closer look into the sata_dwc_460ex code revealed that
the driver did initally set the correct protection control
bits. However, this feature was lost when the sata_dwc_460ex
driver was converted to the generic DMA driver framework.
BugLink: https://forum.openwrt.org/t/wd-mybook-live-duo-two-disks/16195/55
BugLink: https://forum.openwrt.org/t/wd-mybook-live-duo-two-disks/16195/50
Fixes: 8b3444852a ("sata_dwc_460ex: move to generic DMA driver")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The function coh901318_alloc_chan_resources() calls spin_lock_irqsave()
before calling coh901318_config().
But coh901318_config() calls spin_lock_irqsave() again in its
definition, which may cause a double-lock bug.
Because coh901318_config() is only called by
coh901318_alloc_chan_resources(), the bug fix is to remove the
calls to spin-lock and -unlock functions in coh901318_config().
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The MIO DMAC (Media IO DMA Controller) is used in UniPhier LD4,
Pro4, and sLD8 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There's no need to allocate all that memory if these sizes are invalid
anyway.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The `dmaengine_terminate_all()` is marked as deprecated, so update the test
with `dmaengine_terminate_sync()` which is the recommended alternative.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After the DMA transfer is done, we don't need to call the un-mapping code
in 3 places. One is enough.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clang warns:
drivers/dma/xilinx/zynqmp_dma.c:166:4: warning: attribute 'aligned' is
ignored, place it after "struct" to apply attribute to type declaration
[-Wignored-attributes]
}; __aligned(64)
^
./include/linux/compiler_types.h:200:38: note: expanded from macro
'__aligned'
^
1 warning generated.
As Nick pointed out in the previous version of this patch, the author
likely intended for this struct to be 8-byte (64-bit) aligned, not
64-byte, which is the default. Remove the hanging __aligned attribute.
Fixes: b0cc417c16 ("dmaengine: Add Xilinx zynqmp dma engine driver support")
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make the call to dma_alloc_coherent() to fit into a single line, which
helps readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch introduces the xilinx_prep_dma_addr_t macro which prepares
dma_addr_t from hardware buffer descriptor LSB and MSB fields. It will
be used in simple dma 64-bit programming sequence.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
MediaTek Command-Queue DMA controller (CQDMA) on MT6765 SoC is dedicated
to memory-to-memory transfer through queue based descriptor management.
There are only 3 physical channels inside CQDMA, while the driver is
extended to support 32 virtual channels for multiple dma users to issue
dma requests onto the CQDMA simultaneously.
Signed-off-by: Shun-Chih Yu <shun-chih.yu@mediatek.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As we now have no users of sa11x0_dma_filter_fn() in the tree, we can
unexport this function, and remove the now unused header file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The license text is specifying GPL v2 or later but the MODULE_LICENSE
is set to GPL v2 which means GNU Public License v2 only. So choose the
license text as the correct one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Signed-off-by: Vinod Koul <vkoul@kernel.org>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
Change this time round are:
- Support for ColdFire mcf5441x edma controller
- Support for link list mode in sprd dma
- More users of managed dmaenginem_async_device_register API
- Cyclic mode support in owl dma driver
- DT updates for renesas drivers, dma-jz4780 updates and support for
JZ4770, JZ4740 and JZ4725B controllers
- Removal of deprecated dma_slave_config direction in dmaengine drivers,
few more users will be removed in next cycle and eventually users.
- Minor updates to idma64, ioat, pxa, ppc drivers
-----BEGIN PGP SIGNATURE-----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=/pTg
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.20-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Support for ColdFire mcf5441x edma controller
- Support for link list mode in sprd dma
- More users of managed dmaenginem_async_device_register API
- Cyclic mode support in owl dma driver
- DT updates for renesas drivers, dma-jz4780 updates and support for
JZ4770, JZ4740 and JZ4725B controllers
- Removal of deprecated dma_slave_config direction in dmaengine
drivers, few more users will be removed in next cycle and eventually
removed.
- Minor updates to idma64, ioat, pxa, ppc drivers
* tag 'dmaengine-4.20-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (66 commits)
dmaengine: ppc4xx: fix off-by-one build failure
dmaengine: owl: Fix warnings generated during build
dmaengine: fsl-edma: remove dma_slave_config direction usage
dmaengine: rcar-dmac: set scatter/gather max segment size
dmaengine: mmp_tdma: remove dma_slave_config direction usage
dmaengine: ep93xx_dma: remove dma_slave_config direction usage
dmaengine: k3dma: remove dma_slave_config direction usage
dmaengine: k3dma: dont use direction for memcpy
dmaengine: imx-dma: remove dma_slave_config direction usage
dmaengine: idma: remove dma_slave_config direction usage
dmaengine: hsu: remove dma_slave_config direction usage
dmaengine: dw: remove dma_slave_config direction usage
dmaengine: jz4740: remove dma_slave_config direction usage
dmaengine: coh901318: remove dma_slave_config direction usage
dmaengine: bcm2835: remove dma_slave_config direction usage
dmaengine: at_hdmac: remove dma_slave_config direction usage
dmaengine: owl: Add Slave and Cyclic mode support for Actions Semi Owl S900 SoC
dmaengine: ioat: fix prototype of ioat_enumerate_channels
dmaengine: stm32-dma: check whether length is aligned on FIFO threshold
dt-bindings: dmaengine: usb-dmac: Add binding for r8a7744
...
There are two poly_store, but one should have been poly_show.
|adma.c:4382:16: error: conflicting types for 'poly_store'
| static ssize_t poly_store(struct device_driver *dev, const char *buf,
| ^~~~~~~~~~
|adma.c:4363:16: note: previous definition of 'poly_store' was here
| static ssize_t poly_store(struct device_driver *dev, char *buf)
| ^~~~~~~~~~
CC: stable@vger.kernel.org
Fixes: 13efe1a053 ("dmaengine: ppc4xx: remove DRIVER_ATTR() usage")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Following warnings are generated when compiled with W=1,
drivers/dma/owl-dma.c:170: warning: Function parameter or member 'cyclic'
not described in 'owl_dma_txd'
drivers/dma/owl-dma.c:198: warning: Function parameter or member 'cfg' not
described in 'owl_dma_vchan'
drivers/dma/owl-dma.c:198: warning: Function parameter or member 'drq' not
described in 'owl_dma_vchan'
drivers/dma/owl-dma.c:225: warning: Function parameter or member 'irq' not
described in 'owl_dma'
Fix this by adding comments for relevant struct members to appear in
kernel-doc.
Fixes: d64e1b3f5c ("dmaengine: owl: Add Slave and Cyclic mode support for
Actions Semi Owl S900 SoC")
Reported-by: Vinod Koul <vinod.koul@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix warning when running with CONFIG_DMA_API_DEBUG_SG=y by allocating a
device_dma_parameters structure and filling in the max segment size.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Memcpy has no direction (copy from memory to memory) so remove the check
in prep_memcpy()
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add Slave and Cyclic mode support for Actions Semi Owl S900 SoC. The slave
mode supports bus width of 4 bytes common for all peripherals and 1 byte
specific for UART.
The cyclic mode supports only block mode transfer.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After bfcb79fca1 ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a period length is not multiple of FIFO some data may be stuck
within FIFO.
Burst/FIFO Threshold/Period or buffer length check has to be hardened
In any case DMA will grant any request from client but will degraded
any parameters whether awkward.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clang warns when implicitly converting from one enumerated type to
another. Avoid this by using the equivalent value from the expected
type.
drivers/dma/timb_dma.c:548:27: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
td_desc->desc_list_len, DMA_MEM_TO_DEV);
^~~~~~~~~~~~~~
1 warning generated.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The following lockdep splat was observed:
[ 1222.241750] ======================================================
[ 1222.271301] WARNING: possible circular locking dependency detected
[ 1222.301060] 4.16.0-10.el8+5.x86_64+debug #1 Not tainted
[ 1222.326659] ------------------------------------------------------
[ 1222.356565] systemd-shutdow/1 is trying to acquire lock:
[ 1222.382660] ((&ioat_chan->timer)){+.-.}, at: [<00000000f71e1a28>] del_timer_sync+0x5/0xf0
[ 1222.422928]
[ 1222.422928] but task is already holding lock:
[ 1222.451743] (&(&ioat_chan->prep_lock)->rlock){+.-.}, at: [<000000008ea98b12>] ioat_shutdown+0x86/0x100 [ioatdma]
:
[ 1223.524987] Chain exists of:
[ 1223.524987] (&ioat_chan->timer) --> &(&ioat_chan->cleanup_lock)->rlock --> &(&ioat_chan->prep_lock)->rlock
[ 1223.524987]
[ 1223.594082] Possible unsafe locking scenario:
[ 1223.594082]
[ 1223.622630] CPU0 CPU1
[ 1223.645080] ---- ----
[ 1223.667404] lock(&(&ioat_chan->prep_lock)->rlock);
[ 1223.691535] lock(&(&ioat_chan->cleanup_lock)->rlock);
[ 1223.728657] lock(&(&ioat_chan->prep_lock)->rlock);
[ 1223.765122] lock((&ioat_chan->timer));
[ 1223.784095]
[ 1223.784095] *** DEADLOCK ***
[ 1223.784095]
[ 1223.813492] 4 locks held by systemd-shutdow/1:
[ 1223.834677] #0: (reboot_mutex){+.+.}, at: [<0000000056d33456>] SYSC_reboot+0x10f/0x300
[ 1223.873310] #1: (&dev->mutex){....}, at: [<00000000258dfdd7>] device_shutdown+0x1c8/0x660
[ 1223.913604] #2: (&dev->mutex){....}, at: [<0000000068331147>] device_shutdown+0x1d6/0x660
[ 1223.954000] #3: (&(&ioat_chan->prep_lock)->rlock){+.-.}, at: [<000000008ea98b12>] ioat_shutdown+0x86/0x100 [ioatdma]
In the ioat_shutdown() function:
spin_lock_bh(&ioat_chan->prep_lock);
set_bit(IOAT_CHAN_DOWN, &ioat_chan->state);
del_timer_sync(&ioat_chan->timer);
spin_unlock_bh(&ioat_chan->prep_lock);
According to the synchronization rule for the del_timer_sync() function,
the caller must not hold locks which would prevent completion of the
timer's handler.
The timer structure has its own lock that manages its synchronization.
Setting the IOAT_CHAN_DOWN bit should prevent other CPUs from
trying to use that device anyway, there is probably no need to call
del_timer_sync() while holding the prep_lock. So the del_timer_sync()
call is now moved outside of the prep_lock critical section to prevent
the circular lock dependency.
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch fixes the following compilation warning
reported during x86_64 allmodconfig build:
drivers/dma/mcf-edma.c: In function 'mcf_edma_filter_fn':
drivers/dma/mcf-edma.c:296:33: warning: cast from pointer to
integer of different size [-Wpointer-to-int-cast]
return (mcf_chan->slave_id == (u32)param);
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
idma64_chan_irq() is invoked in hardirq handle function, it is unnecessary
to call spin_lock_irqsave.
Signed-off-by: Zhaoxiong Yuan <yuanzhx326@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is the standard method provided by dmaengine header.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Func jz4780_dma_desc_residue() expects the index to the next hw
descriptor as its last parameter. Caller func jz4780_dma_tx_status(),
however, applied modulus before passing it. When the current hw
descriptor was last in the list, the index passed became zero.
The resulting excess of reported residue especially caused problems
with cyclic DMA transfer clients, i.e. ALSA AIC audio output, which
rely on this for determining current DMA location within buffer.
Combined with the recent and related residue-reporting fixes, spurious
ALSA audio underruns on jz4770 hardware are now fixed.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Normally, we wouldn't set the channel transfer count register directly
when using descriptor-driven transfers. However, there is no harm in
doing so, and it allows jz4780_dma_desc_residue() to report the correct
residue of an ongoing transfer, no matter when it is called.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simple cleanup, no changes to actual logic here.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 'dtc' word in jz DMA descriptors contains two fields: The
lowest 24 bits are the transfer count, and upper 8 bits are the DOA
offset to next descriptor. The upper 8 bits are now correctly masked
off when computing residue in jz4780_dma_desc_residue(). Note that
reads of the DTCn hardware reg are automatically masked this way.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With the fast DMA bit set, the DMA will transfer twice as much data
per clock period to the AIC, so there is little point not to set it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4725B has one DMA core starring six DMA channels.
As for the JZ4770, each DMA channel's clock can be enabled with
a register write, the difference here being that once started, it
is not possible to turn it off.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4740 SoC has a single DMA core starring six DMA channels.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4770 SoC has two DMA cores, each one featuring six DMA channels.
The major change is that each channel's clock can be enabled or disabled
through register writes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If we make this driver depend on MACH_JZ4780, that means it can be
enabled only if we're building a kernel specially crafted for a
JZ4780-based board, while most GNU/Linux distributions will want one
generic MIPS kernel that works on multiple boards.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The only information we use in the 8-word version of the hardware DMA
descriptor that is not present in the 4-word version is the transfer
type, aka. the ID of the source or recipient device.
Since the transfer type will never change for a DMA channel in use,
we can just set it once for all in the corresponding DMA register
before starting any transfer.
This has several benefits:
* the driver will handle twice as many hardware DMA descriptors;
* the driver is closer to support the JZ4740, which only supports 4-word
hardware DMA descriptors;
* the JZ4770 SoC needs the transfer type to be set in the corresponding
DMA register anyway, even if 8-word descriptors are in use.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The register area of the JZ4780 DMA core can be split into different
sections for different purposes:
* one set of registers is used to perform actions at the DMA core level,
that will generally affect all channels;
* one set of registers per DMA channel, to perform actions at the DMA
channel level, that will only affect the channel in question.
The problem rises when trying to support new versions of the JZ47xx
Ingenic SoC. For instance, the JZ4770 has two DMA cores, each one
with six DMA channels, and the register sets are interleaved:
<DMA0 chan regs> <DMA1 chan regs> <DMA0 ctrl regs> <DMA1 ctrl regs>
By using one memory resource for the channel-specific registers and
one memory resource for the core-specific registers, we can support
the JZ4770, by initializing the driver once per DMA core with different
addresses.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As part of the work to support various other Ingenic JZ47xx SoC versions,
which don't feature the same number of DMA channels per core, we now
deduce the number of DMA channels available from the devicetree
compatible string.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver calls clk_get() with the clock name set to NULL, which means
that the driver could only work when probed from devicetree. From now
on, we explicitly require the driver to be probed from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds support for ColdFire mcf5441x-family edma
module.
The ColdFire edma module is slightly different from fsl-edma,
so a new driver is added. But most of the code is common
between fsl-edma and mcf-edma so it has been collected into a
separate common module fsl-edma-common (patch 1/3).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch fixes macros to use BIT() and GENMASK(), removing
also some unneeded.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds configurable registers (using __iomem addresses)
to allow the use of fsl-edma-common code with slightly different
edma module versions, as Vybrid (v1) and ColdFire (v2) are.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds a new fsl-edma-common module to allow new
mcf-edma module code to use most of the fsl-edma code.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We have build failures attributed to turning on COMPILE_TEST, so revert
commit 90082cd397aeb: ("dmaengine: add COMPILE_TEST for the drivers")
while we fix these.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Spreadtrum DMA can support the link-list transaction mode, which means
DMA controller can do transaction one by one automatically once we linked
these transaction by link-list register.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
as you are already in a tasklet, it is unnecessary to call spin_lock_bh.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
as you are already in a tasklet, it is unnecessary to call spin_lock_bh.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
as you are already in a tasklet, it is unnecessary to call spin_lock_bh.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Bay and Cherry Trail DSTDs represent a different set of devices depending
on which OS the device think it is booting. One set of decices for Windows
and another set of devices for Android which targets the Android-x86 Linux
kernel fork (which e.g. used to have its own display driver instead of
using the i915 driver).
Which set of devices we are actually going to get is out of our control,
this is controlled by the ACPI OSID variable, which gets either set through
an EFI setup option, or sometimes is autodetected. So we need to support
both.
This commit adds support for the 80862286 and 808622C0 ACPI HIDs which we
get for the first resp. second DMA controller on Cherry Trail devices when
OSID is set to Android.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We can do the compiling test with COMPILE_TEST.
This patch adds the COMPILE_TEST for the drivers.
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use dmaenginem_async_device_register to simplify the code:
remove dma_async_device_unregister.
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use dmaenginem_async_device_register to simplify the code:
remove dma_async_device_unregister.
return error if it fails.
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The following patch introduced an issue.
commit f6206f00d8 ("dmaengine: mic_x100_dma: use the new helper to simplify the code")
This issue is :
kfree(mic_dma_dev)
.....
dma_async_device_unregister(mic_dma_dev->device);
Free the memory, and use it again.
So use devm_kzalloc to allocate mic_dma_dev to fix it.
When the Devres try to release the resources, it will call release at the
following order:
dma_async_device_unregister(mic_dma_dev->device);
.....
kfree(mic_dma_dev)
Fixes: f6206f00d8 ("dmaengine: mic_x100_dma: use the new helper to simplify the code")
Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
This round brings couple of framework changes, a new driver and usual driver
updates:
- New managed helper for dmaengine framework registration
- Split dmaengine pause capability to pause and resume and allow drivers to
report that individually
- Update dma_request_chan_by_mask() to handle deferred probing
- Move imx-sdma to use virt-dma
- New driver for Actions Semi Owl family S900 controller
- Minor updates to intel, renesas, mv_xor, pl330 etc
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJbdsctAAoJEHwUBw8lI4NHZrIP/3/HrNSUKApt1KdOcG5UA7nu
7O3BcvkAahmM285Hw3a/zLEnSm2sJ/6EI0lN1sz+VYi8IECG7nbCyHQh3Bd1Mxi1
XLHafdTGcI5b7rpicNtRS1BHCPtNrgOypFxs8b/bTatbzc/aWM8K8WFLX27sqGZT
1Sb2nNKKrVbQDVqJ+1ZEQ4q86w61tPHmmRH0icl1DAQREfsvbu/bRMdol5H7/orx
A+ZGH39Ig3FI8/Ri8KccqShvG0VM1yCVJca+0j30IL1x4JNZ36uG+NQbtkBIkOJC
kk9qfCu3ugm4NOtfKGOtkmmOwE9/GirRh+QMPpSmi6oQu4vdOVxyQyYpKukHIer1
vxwpvo2b+3POMfHi1kuqDJhcGIEPak6tH2Oyd01l7nA7Lyww9iC2AyiL89knw+i6
aUK4oHIhf2fFLUN6/ck4JbBqQ3MrDNraZfLJcnmQPtpTftW9Yqd2yqs7Cf1gcBC9
jyLAekJENiUmaNJsL5nJUMDVGG0lIiOnfwtPNfPZJuWu+4doKb2pM4+Ljcyfn2g0
ub4fPfXp0wcFaVarjpQr6T0tdZVMpmrPSTPGS5BdVZbWntrNOpiHmmPVEOLNz3zb
ibIMFn478/RYYB5pcNtHkUaOF4tu0w46fSqRp1ixkey+FIHKlj8/B+YeaAJF0nJh
fc4XaTTJgLufzc1F0ztU
=kbCC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.19-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull DMAengine updates from Vinod Koul:
"This round brings couple of framework changes, a new driver and usual
driver updates:
- new managed helper for dmaengine framework registration
- split dmaengine pause capability to pause and resume and allow
drivers to report that individually
- update dma_request_chan_by_mask() to handle deferred probing
- move imx-sdma to use virt-dma
- new driver for Actions Semi Owl family S900 controller
- minor updates to intel, renesas, mv_xor, pl330 etc"
* tag 'dmaengine-4.19-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Add Actions Semi Owl family S900 DMA driver
dt-bindings: dmaengine: Add binding for Actions Semi Owl SoCs
dmaengine: sh: rcar-dmac: Should not stop the DMAC by rcar_dmac_sync_tcr()
dmaengine: mic_x100_dma: use the new helper to simplify the code
dmaengine: add a new helper dmaenginem_async_device_register
dmaengine: imx-sdma: add memcpy interface
dmaengine: imx-sdma: add SDMA_BD_MAX_CNT to replace '0xffff'
dmaengine: dma_request_chan_by_mask() to handle deferred probing
dmaengine: pl330: fix irq race with terminate_all
dmaengine: Revert "dmaengine: mv_xor_v2: enable COMPILE_TEST"
dmaengine: mv_xor_v2: use {lower,upper}_32_bits to configure HW descriptor address
dmaengine: mv_xor_v2: enable COMPILE_TEST
dmaengine: mv_xor_v2: move unmap to before callback
dmaengine: mv_xor_v2: convert callback to helper function
dmaengine: mv_xor_v2: kill the tasklets upon exit
dmaengine: mv_xor_v2: explicitly freeup irq
dmaengine: sh: rcar-dmac: Add dma_pause operation
dmaengine: sh: rcar-dmac: add a new function to clear CHCR.DE with barrier
dmaengine: idma64: Support dmaengine_terminate_sync()
dmaengine: hsu: Support dmaengine_terminate_sync()
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Christian Lamparter