Another QMI speaking Qualcomm based device, which should be
driven by qmi_wwan, while cdc_ether should ignore it.
Like on other Huawei devices, the wwan function can appear
either as a single vendor specific interface or as a CDC ECM
class function using separate control and data interfaces.
The ECM control interface protocol is 0xff, likely in an
attempt to indicate that vendor specific management is
required.
In addition to the near standard CDC class, Huawei also add
vendor specific AT management commands to their firmwares.
This is probably an attempt to support non-Windows systems
using standard class drivers. Unfortunately, this part of
the firmware is often buggy. Linux is much better off using
whatever native vendor specific management protocol the
device offers, and Windows uses, whenever possible. This
means QMI in the case of Qualcomm based devices.
The E1820 has been verified to work fine with QMI.
Matching on interface number is necessary to distiguish the
wwan function from serial functions in the single interface
mode, as both function types will have class/subclass/function
set to ff/ff/ff.
The control interface number does not change in CDC ECM mode,
so the interface number matching rule is sufficient to handle
both modes. The cdc_ether blacklist entry is only relevant in
CDC ECM mode, but using a similar interface number based rule
helps document this as a transfer from one driver to another.
Other Huawei 02/06/ff devices are left with the cdc_ether driver
because we do not know whether they are based on Qualcomm chips.
The Huawei specific AT command management is known to be somewhat
hardware independent, and their usage of these class codes may
also be independent of the modem hardware.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel writes:
Just tiny regression fixes here:
- Two fixes to fix sdvo hotplug which broke in the hpd storm detection
work.
- One fix to patch-up the sdvo lvds regression fixer from the last pull -
we need to prefer the vbt mode over edid modes.
* tag 'drm-intel-fixes-2013-06-11' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: prefer VBT modes for SVDO-LVDS over EDID
drm/i915: Enable hotplug interrupts after querying hw capabilities.
drm/i915: Fix hotplug interrupt enabling for SDVOC
When the first loop in sh_eth_check_reset() runs to its end, 'cnt' is 0, so the
following check for 'cnt < 0' fails to catch the timeout. Fix the condition in
this check, so that the timeout is actually reported.
While at it, fix the grammar in the failure message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
was playing with suspend and run into this:
|BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:891
|in_atomic(): 1, irqs_disabled(): 0, pid: 1963, name: bash
|6 locks held by bash/1963:
|CPU: 0 PID: 1963 Comm: bash Not tainted 3.10.0-rc4+ #50
|[<c0014fdc>] (unwind_backtrace+0x0/0xf8) from [<c0011da4>] (show_stack+0x10/0x14)
|[<c0011da4>] (show_stack+0x10/0x14) from [<c02e8680>] (__pm_runtime_idle+0xa4/0xac)
|[<c02e8680>] (__pm_runtime_idle+0xa4/0xac) from [<c0341158>] (davinci_mdio_suspend+0x6c/0x9c)
|[<c0341158>] (davinci_mdio_suspend+0x6c/0x9c) from [<c02e0628>] (platform_pm_suspend+0x2c/0x54)
|[<c02e0628>] (platform_pm_suspend+0x2c/0x54) from [<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64)
|[<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64) from [<c02e57e4>] (__device_suspend+0x100/0x22c)
|[<c02e57e4>] (__device_suspend+0x100/0x22c) from [<c02e67e8>] (dpm_suspend+0x68/0x230)
|[<c02e67e8>] (dpm_suspend+0x68/0x230) from [<c0072a20>] (suspend_devices_and_enter+0x68/0x350)
|[<c0072a20>] (suspend_devices_and_enter+0x68/0x350) from [<c0072f18>] (pm_suspend+0x210/0x24c)
|[<c0072f18>] (pm_suspend+0x210/0x24c) from [<c0071c74>] (state_store+0x6c/0xbc)
|[<c0071c74>] (state_store+0x6c/0xbc) from [<c02714dc>] (kobj_attr_store+0x14/0x20)
|[<c02714dc>] (kobj_attr_store+0x14/0x20) from [<c01341a0>] (sysfs_write_file+0x16c/0x19c)
|[<c01341a0>] (sysfs_write_file+0x16c/0x19c) from [<c00ddfe4>] (vfs_write+0xb4/0x190)
|[<c00ddfe4>] (vfs_write+0xb4/0x190) from [<c00de3a4>] (SyS_write+0x3c/0x70)
|[<c00de3a4>] (SyS_write+0x3c/0x70) from [<c000e2c0>] (ret_fast_syscall+0x0/0x48)
I don't see a reason why the pm_runtime call must be under the lock.
Further I don't understand why this is a spinlock and not mutex.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EE is hard-disabled on entry to kvmppc_handle_exit(), so call
hard_irq_disable() so that PACA_IRQ_HARD_DIS is set, and soft_enabled
is unset.
Without this, we get warnings such as arch/powerpc/kernel/time.c:300,
and sometimes host kernel hangs.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
KVM core expects arch code to acquire the srcu lock when calling
gfn_to_memslot and similar functions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The previous patch made 64-bit booke KVM build again, but Altivec
support is still not complete, and we can't prevent the guest from
turning on Altivec (which can corrupt host state until state
save/restore is implemented). Disable e6500 on KVM until this is
fixed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Interrupt numbers defined for Book3E follows IVORs definition. Align
BOOKE_INTERRUPT_ALTIVEC_UNAVAIL and BOOKE_INTERRUPT_ALTIVEC_ASSIST to this
rule which also fixes the build breakage.
IVORs 32 and 33 are shared so reflect this in the interrupts naming.
This fixes a build break for 64-bit booke KVM.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This patch makes legacy code on suspend/resume path being executed
conditionally, on non-DT platforms only, to fix suspend/resume of
DT-enabled systems, for which the code is inappropriate.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[olof: add #include <linux/of.h>]
Signed-off-by: Olof Johansson <olof@lixom.net>
The API requires that the GET_ONE_REG and SET_ONE_REG ioctls have this
extra information encoded in the register identifiers.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
We use 0x7000000000000000ULL as 0x6000000000000000ULL is reserved for
ARM64.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
In prima2, some functions of checking DT is registered in initcall
level. If it doesn't match the compatible name of sirf, kernel
will panic. It blocks the usage of multiplatform on other verndor.
The error message is in below.
Knic - not syncing: unable to find compatible pwrc node in dtb
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0-rc3-00006-gd7f26ea-dirty #86
[<c0013adc>] (unwind_backtrace+0x0/0xf8) from [<c0011430>] (show_stack+0x10/0x1)
[<c0011430>] (show_stack+0x10/0x14) from [<c026f724>] (panic+0x90/0x1e8)
[<c026f724>] (panic+0x90/0x1e8) from [<c03267fc>] (sirfsoc_of_pwrc_init+0x24/0x)
[<c03267fc>] (sirfsoc_of_pwrc_init+0x24/0x58) from [<c0320864>] (do_one_initcal)
[<c0320864>] (do_one_initcall+0x90/0x150) from [<c0320a20>] (kernel_init_freeab)
[<c0320a20>] (kernel_init_freeable+0xfc/0x1c4) from [<c026b9e8>] (kernel_init+0)
[<c026b9e8>] (kernel_init+0x8/0xe4) from [<c000e158>] (ret_from_fork+0x14/0x3c)
Signen-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Filters need to be translated to real BPF code for userland, like SO_GETFILTER.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stop machine logic can lock up if all but one of the migration
threads make it through the disable-irq step and the one remaining
thread gets stuck in __do_softirq. The reason __do_softirq can hang is
that it has a bail-out based on jiffies timeout, but in the lockup case,
jiffies itself is not incremented.
To work around this, re-add the max_restart counter in __do_irq and stop
processing irqs after 10 restarts.
Thanks to Tejun Heo and Rusty Russell and others for helping me track
this down.
This was introduced in 3.9 by commit c10d73671a ("softirq: reduce
latencies").
It may be worth looking into ath9k to see if it has issues with its irq
handler at a later date.
The hang stack traces look something like this:
------------[ cut here ]------------
WARNING: at kernel/watchdog.c:245 watchdog_overflow_callback+0x9c/0xa7()
Watchdog detected hard LOCKUP on cpu 2
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
Pid: 23, comm: migration/2 Tainted: G C 3.9.4+ #11
Call Trace:
<NMI> warn_slowpath_common+0x85/0x9f
warn_slowpath_fmt+0x46/0x48
watchdog_overflow_callback+0x9c/0xa7
__perf_event_overflow+0x137/0x1cb
perf_event_overflow+0x14/0x16
intel_pmu_handle_irq+0x2dc/0x359
perf_event_nmi_handler+0x19/0x1b
nmi_handle+0x7f/0xc2
do_nmi+0xbc/0x304
end_repeat_nmi+0x1e/0x2e
<<EOE>>
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
---[ end trace 4947dfa9b0a4cec3 ]---
BUG: soft lockup - CPU#1 stuck for 22s! [migration/1:17]
Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
irq event stamp: 835637905
hardirqs last enabled at (835637904): __do_softirq+0x9f/0x257
hardirqs last disabled at (835637905): apic_timer_interrupt+0x6d/0x80
softirqs last enabled at (5654720): __do_softirq+0x1ff/0x257
softirqs last disabled at (5654725): irq_exit+0x5f/0xbb
CPU 1
Pid: 17, comm: migration/1 Tainted: G WC 3.9.4+ #11 To be filled by O.E.M. To be filled by O.E.M./To be filled by O.E.M.
RIP: tasklet_hi_action+0xf0/0xf0
Process migration/1
Call Trace:
<IRQ>
__do_softirq+0x117/0x257
irq_exit+0x5f/0xbb
smp_apic_timer_interrupt+0x8a/0x98
apic_timer_interrupt+0x72/0x80
<EOI>
printk+0x4d/0x4f
stop_machine_cpu_stop+0x22c/0x274
cpu_stopper_thread+0xae/0x162
smpboot_thread_fn+0x258/0x260
kthread+0xc7/0xcf
ret_from_fork+0x7c/0xb0
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Pekka Riikonen <priikone@iki.fi>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patrik writes:
Two fixes for memory leaks split into Cedarview and Poulsbo versions,
and a fix for properly setting the pipe base when using fbdev. It's on
my todo-list to start unifying the chips since they are very similar,
but until then I'd like to split them up in case there are side-effects
on Cedarview that I cannot currently test.
airled: Verified pull from github matches what I expected.
* 'gma500-fixes' of git://github.com/patjak/drm-gma500:
drm/gma500/cdv: Fix cursor gem obj referencing on cdv
drm/gma500/psb: Fix cursor gem obj referencing on psb
drm/gma500/cdv: Unpin framebuffer on crtc disable
drm/gma500/psb: Unpin framebuffer on crtc disable
drm/gma500: Add fb gtt offset to fb base
Complier may generate codes that re-read the tun->numqueues during
tun_select_queue(). This may be a race if vlan->numqueues were changed in the
same time and can lead unexpected result (e.g. very huge value).
We need prevent the compiler from generating such codes by adding an
ACCESS_ONCE() to make sure tun->numqueues were only read once.
Bug were introduced by commit c8d68e6be1
(tuntap: multiqueue support).
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we decide not use zero-copy, msg.control should be set to NULL otherwise
macvtap/tap may set zerocopy callbacks which may decrease the kref of ubufs
wrongly.
Bug were introduced by commit cedb9bdce0
(vhost-net: skip head management if no outstanding).
This solves the following warnings:
WARNING: at include/linux/kref.h:47 handle_tx+0x477/0x4b0 [vhost_net]()
Modules linked in: vhost_net macvtap macvlan tun nfsd exportfs bridge stp llc openvswitch kvm_amd kvm bnx2 megaraid_sas [last unloaded: tun]
CPU: 5 PID: 8670 Comm: vhost-8668 Not tainted 3.10.0-rc2+ #1566
Hardware name: Dell Inc. PowerEdge R715/00XHKG, BIOS 1.5.2 04/19/2011
ffffffffa0198323 ffff88007c9ebd08 ffffffff81796b73 ffff88007c9ebd48
ffffffff8103d66b 000000007b773e20 ffff8800779f0000 ffff8800779f43f0
ffff8800779f8418 000000000000015c 0000000000000062 ffff88007c9ebd58
Call Trace:
[<ffffffff81796b73>] dump_stack+0x19/0x1e
[<ffffffff8103d66b>] warn_slowpath_common+0x6b/0xa0
[<ffffffff8103d6b5>] warn_slowpath_null+0x15/0x20
[<ffffffffa0197627>] handle_tx+0x477/0x4b0 [vhost_net]
[<ffffffffa0197690>] handle_tx_kick+0x10/0x20 [vhost_net]
[<ffffffffa019541e>] vhost_worker+0xfe/0x1a0 [vhost_net]
[<ffffffffa0195320>] ? vhost_attach_cgroups_work+0x30/0x30 [vhost_net]
[<ffffffffa0195320>] ? vhost_attach_cgroups_work+0x30/0x30 [vhost_net]
[<ffffffff81061f46>] kthread+0xc6/0xd0
[<ffffffff81061e80>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff817a1aec>] ret_from_fork+0x7c/0xb0
[<ffffffff81061e80>] ? kthread_freezable_should_stop+0x70/0x70
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the UEFI anti-bricking code, including an effective
reversion of cc5a080c and 31ff2f20. It turns out that calling
QueryVariableInfo() from boot services results in some firmware
implementations jumping to physical addresses even after entering virtual
mode, so until we have 1:1 mappings for UEFI runtime space this isn't
going to work so well.
Reverting these gets us back to the situation where we'd refuse to create
variables on some systems because they classify deleted variables as "used"
until the firmware triggers a garbage collection run, which they won't do
until they reach a lower threshold. This results in it being impossible to
install a bootloader, which is unhelpful.
Feedback from Samsung indicates that the firmware doesn't need more than
5KB of storage space for its own purposes, so that seems like a reasonable
threshold. However, there's still no guarantee that a platform will attempt
garbage collection merely because it drops below this threshold. It seems
that this is often only triggered if an attempt to write generates a
genuine EFI_OUT_OF_RESOURCES error. We can force that by attempting to
create a variable larger than the remaining space. This should fail, but if
it somehow succeeds we can then immediately delete it.
I've tested this on the UEFI machines I have available, but I don't have
a Samsung and so can't verify that it avoids the bricking problem.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Lee, Chun-Y <jlee@suse.com> [ dummy variable cleanup ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
__DECLARE_TRACE_RCU() currently creates an _rcuidle() tracepoint which
may safely be invoked from what RCU considers to be an idle CPU.
However, these _rcuidle() tracepoints may -not- be invoked from the
handler of an irq taken from idle, because rcu_idle_enter() zeroes
RCU's nesting-level counter, so that the rcu_irq_exit() returning to
idle will trigger a WARN_ON_ONCE().
This commit therefore substitutes rcu_irq_enter() for rcu_idle_exit()
and rcu_irq_exit() for rcu_idle_enter() in order to make the _rcuidle()
tracepoints usable from irq handlers as well as from process context.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Pablo Neira Ayuso says:
====================
The following patchset contains four fixes for Netfilter and one fix
for IPVS, they are:
* Fix data leak to user-space via getsockopt IP_VS_SO_GET_DESTS, from
Dan Carpenter.
* Fix xt_TCPMSS if no TCP MSS is specified in syn packets, to avoid the
violation of RFC879, from Phil Oester.
* Fix incomplete dump of objects via nfnetlink_acct and nfnetlink_cttimeout,
from myself.
* Fix missing HW protocol in packets passed to user-space via NFQUEUE,
from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A few nasty issues, particularly a race with the interrupt controller in
the xilinx driver, together with a couple of more minor fixes and a much
needed move of the mailing list away from sourceforge.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Lvj8
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few nasty issues, particularly a race with the interrupt controller
in the xilinx driver, together with a couple of more minor fixes and a
much needed move of the mailing list away from sourceforge."
* tag 'spi-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: hspi: fixup long delay time
spi: spi-xilinx: Remove ISR race condition
spi: topcliff-pch: fix error return code in pch_spi_probe()
spi: topcliff-pch: Pass correct pointer to free_irq()
spi: Move mailing list to vger
- xen/tmem stopped working after a certain combination of modprobe/swapon was used
- cpu online/offlining would trigger WARN_ON.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRtgQxAAoJEFjIrFwIi8fJ9QYH/ibEGBlKLfGzN4Apx6evBA68
l9CuLIpGCkPOiJLgVs10zY77Sg3f95bHFkJrwrEIDeTQ42joNKybsIp+qZCIS5CW
sAnzSd6Mb8jqQYJpgLl03+z3GdFzILTJ9e0zYTETbW2vfLpAETm87XWH+gjxDK0e
9I0kZX+Q3+2VWi5xv+UwWkYIOLbggLyKYajTHDwWNuC7vQgkJulCAbmjgN/NBv7A
xacvXdbEClIfZ5tvJJN0RggdEWo6WyTxyExfLPmpXFbHEvWDUX5LPEf8MhFY1ORK
U1C0BSV6YuLo350G5lY4I0R75ZEWLeUyVkZFnJIeGnUF1rP6OXEuVWTyeivPDBA=
=Fy36
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.10-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two bug-fixes for regressions:
- xen/tmem stopped working after a certain combination of
modprobe/swapon was used
- cpu online/offlining would trigger WARN_ON."
* tag 'stable/for-linus-3.10-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/tmem: Don't over-write tmem_frontswap_poolid after tmem_frontswap_init set it.
xen/smp: Fixup NOHZ per cpu data when onlining an offline CPU.
The biggest fix here is Lars-Peter's fix for custom locking callbacks
which is pretty localised but important for those devices that use the
feature. Otherwise we've got a couple of fairly small cleanups which
would have been sent sooner were it not for letting Lars-Peter's patch
soak for a while.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mOJz
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"The biggest fix here is Lars-Peter's fix for custom locking callbacks
which is pretty localised but important for those devices that use the
feature. Otherwise we've got a couple of fairly small cleanups which
would have been sent sooner were it not for letting Lars-Peter's patch
soak for a while"
* tag 'regmap-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Fixed node range check on sync
regmap: regcache: Fixup locking for custom lock callbacks
regmap: debugfs: Check return value of regmap_write()
Pull crypto fixes from Herbert Xu:
"This fixes a build problem in sahara and temporarily disables two new
optimisations because of performance regressions until a permanent fix
is ready"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: sahara - fix building as module
crypto: blowfish - disable AVX2 implementation
crypto: twofish - disable AVX2 implementation
Do not use uninitialised termios data to determine when to configure the
device at open.
This also prevents stack data from leaking to userspace in the OOM error
path.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use uninitialised termios data to determine when to configure the
device at open.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use uninitialised termios data to determine when to configure the
device at open.
This also prevents stack data from leaking to userspace.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arch_ftrace_update_code and ftrace_modify_all_code are only
available if CONFIG_DYNAMIC_FTRACE is selected.
Fixes the following build problem on MIPS randconfig:
arch/mips/kernel/ftrace.c: In function 'arch_ftrace_update_code':
arch/mips/kernel/ftrace.c:31:2: error: implicit declaration of function
'ftrace_modify_all_code' [-Werror=implicit-function-declaration]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5435/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kvm_* symbols are only available if KVM is selected.
Fixes the following linking problem on a randconfig:
arch/mips/built-in.o: In function `local_flush_tlb_mm':
(.text+0x18a94): undefined reference to `kvm_local_flush_tlb_all'
arch/mips/built-in.o: In function `local_flush_tlb_range':
(.text+0x18d0c): undefined reference to `kvm_local_flush_tlb_all'
kernel/built-in.o: In function `__schedule':
core.c:(.sched.text+0x2a00): undefined reference to `kvm_local_flush_tlb_all'
mm/built-in.o: In function `use_mm':
(.text+0x30214): undefined reference to `kvm_local_flush_tlb_all'
fs/built-in.o: In function `flush_old_exec':
(.text+0xf0a0): undefined reference to `kvm_local_flush_tlb_all'
make: *** [vmlinux] Error 1
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5437/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only an interrupt can wake the core from 'wait', enable interrupts
locally before executing 'wait'.
[ralf@linux-mips.org: This leave the race between an interrupt that's
setting TIF_NEED_RESCHEd and entering the WAIT status. but at least it's
going to bring Alchemy back from the dead, so I'm going to apply this
patch.]
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5408/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 10a7a07713 ("xen: tmem: enable Xen
tmem shim to be built/loaded as a module") allows the tmem module
to be loaded any time. For this work the frontswap API had to
be able to asynchronously to call tmem_frontswap_init before
or after the swap image had been set. That was added in git
commit 905cd0e1bf
("mm: frontswap: lazy initialization to allow tmem backends to build/run as modules").
Which means we could do this (The common case):
modprobe tmem [so calls frontswap_register_ops, no ->init]
modifies tmem_frontswap_poolid = -1
swapon /dev/xvda1 [__frontswap_init, calls -> init, tmem_frontswap_poolid is
< 0 so tmem hypercall done]
Or the failing one:
swapon /dev/xvda1 [calls __frontswap_init, sets the need_init bitmap]
modprobe tmem [calls frontswap_register_ops, -->init calls, finds out
tmem_frontswap_poolid is 0, does not make a hypercall.
Later in the module_init, sets tmem_frontswap_poolid=-1]
Which meant that in the failing case we would not call the hypercall
to initialize the pool and never be able to make any frontswap
backend calls.
Moving the frontswap_register_ops after setting the tmem_frontswap_poolid
fixes it.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
All architectures must implement IRQ functions. Since various
dependencies on !S390 were removed, there are various drivers that can
be selected but will fail to link. Provide a dummy implementation of
these functions for the !PCI case.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org # 3.9
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The entry struct has a 2 byte hole after ->port and another 4 byte
hole after ->stats.outpkts. You must have CAP_NET_ADMIN in your
namespace to hit this information leak.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With the introduction of ACPI scan handlers, ACPI device objects
with an ACPI scan handler attached to them must not be bound to
by ACPI drivers any more. Unfortunately, however, the ACPI video
driver attempts to do just that if there is a _ROM ACPI control
method defined under a device object with an ACPI scan handler.
Prevent that from happening by making the video driver's "add"
routine check if the device object already has an ACPI scan handler
attached to it and return an error code in that case.
That is not sufficient, though, because acpi_bus_driver_init() would
then clear the device object's driver_data that may be set by its
scan handler, so for the fix to work acpi_bus_driver_init() has to be
modified to leave driver_data as is on errors.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091
Bisected-and-tested-by: Dmitry S. Demin <dmitryy.demin@gmail.com>
Reported-and-tested-by: Jason Cassell <bluesloth600@gmail.com>
Tracked-down-by: Aaron Lu <aaron.lu@intel.com>
Cc: 3.9+ <stable@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
In
commit 53d3b4d777
Author: Egbert Eich <eich@suse.de>
Date: Tue Jun 4 17:13:21 2013 +0200
drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC
Egbert Eich fixed a long-standing bug where we simply used a
non-working i2c controller to read the EDID for SDVO-LVDS panels.
Unfortunately some machines seem to not be able to cope with the mode
provided in the EDID. Specifically they seem to not be able to cope
with a 4x pixel mutliplier instead of a 2x one, which seems to have
been worked around by slightly changing the panels native mode in the
VBT so that the dotclock is just barely above 50MHz.
Since it took forever to notice the breakage it's fairly safe to
assume that at least for SDVO-LVDS panels the VBT contains fairly sane
data. So just switch around the order and use VBT modes first.
v2: Also add EDID modes just in case, and spell Egbert correctly.
v3: Elaborate a bit more about what's going on on Chris' machine.
Cc: Egbert Eich <eich@suse.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65524
Cc: stable@vger.kernel.org
Reported-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
sdvo->hotplug_active is initialised during intel_sdvo_setup_outputs(),
and so we never enabled the hotplug interrupts on SDVO as we were
checking too early.
This regression has been introduced somewhere in the hpd rework for
the storm detection and handling starting with
commit 1d843f9de4
Author: Egbert Eich <eich@suse.de>
Date: Mon Feb 25 12:06:49 2013 -0500
DRM/I915: Add enum hpd_pin to intel_encoder.
and the follow-up patches to use the new encoder->hpd_pin variable for
the different irq setup functions.
The problem is that encoder->hpd_pin was set up _before_ the output
setup was done and so before we could assess the hotplug capabilities
of the outputs on an sdvo encoder.
Reported-by: Alex Fiestas <afiestas@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add regression note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A broken conditional would lead to SDVOC waiting upon hotplug events on
SDVOB - and so miss all activity on its SDVO port.
This regression has been introduced in
commit 1d843f9de4
Author: Egbert Eich <eich@suse.de>
Date: Mon Feb 25 12:06:49 2013 -0500
DRM/I915: Add enum hpd_pin to intel_encoder.
References: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add regression note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bridge loop avoidance has a hook to handle address updates of the
originator. These should not be handled when bridge loop avoidance is
disabled - it might send some bridge loop avoidance packets which should
not appear if bla is disabled.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When a packet is received from another node first and later from the
best next hop, this packet is dropped. However the first OGM was sent
with the BATADV_NOT_BEST_NEXT_HOP flag and thus dropped by neighbors.
The late OGM from the best neighbor is then dropped because it is a
duplicate.
If this situation happens constantly, a node might end up not forwarding
the "valid" OGMs anymore, and nodes behind will starve from not getting
valid OGMs.
Fix this by refining the duplicate checking behaviour: The actions
should depend on whether it was a duplicate for a neighbor only or for
the originator. OGMs which are not duplicates for a specific neighbor
will now be considered in batadv_iv_ogm_forward(), but only actually
forwarded for the best next hop. Therefore, late OGMs from the best
next hop are forwarded now and not dropped as duplicates anymore.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The rtnl_lock in batadv_store_mesh_iface has been converted to a rtnl_trylock
some time ago to avoid a possible deadlock between rtnl and s_active on removal
of the sysfs nodes.
The behaviour introduced by that was quite confusing as it could lead to the
sysfs store to fail, making batman-adv setup scripts unreliable. As recently the
sysfs removal was postponed to a worker not running with the rtnl taken, the
deadlock can't occur any more and it is safe to change the trylock back to a
lock to make the sysfs store reliable again.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Pull powerpc fixes from Benjamin Herrenschmidt:
"This is purely regressions (though not all recent ones) or stable
material"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Partial revert of "Context switch more PMU related SPRs"
powerpc/perf: Fix deadlock caused by calling printk() in PMU exception
powerpc/hw_breakpoints: Add DABRX cpu feature to fix 32-bit regression
powerpc/power8: Update denormalization handler
powerpc/pseries: Simplify denormalization handler
powerpc/power8: Fix oprofile and perf
powerpc/eeh: Don't check RTAS token to get PE addr
powerpc/pci: Check the bus address instead of resource address in pcibios_fixup_resources
Bjørn Mork