The DIP registers are a mess on VLV and CHV. The register block on pipe
A is different than the register block on pipes B and C. In order to
handle that using the pipe offsets, we'd need a new pipe offset per
register, which seems wasteful. So instead just use the _PIPE3() macro
to handle these registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are just single registers so wasting space for the pipe offsets
seems a bit pointless. So just use the _PIPE3() macro instead.
Also rewrite the _PIPE3() macro to be more obvious, and protect the
arguments properly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Frob conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we forced the clock buffers on in .pre_pll_enable() we
should probably undo the damage after we've turned the PLL off.
We do the clock buffer force enable in the .pre_pll_enable() hook
as we need to know which port is going to be used, but in the disable
case we don't need the port since we just disable the clock buffers
to both channels. So we can do this in chv_disable_pll() instead
of having to add any kind of .post_pll_disable() hook.
v2: Improve the commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to force the PHY clock buffer enables to make the clock routing
work.
v2: Fix the pipe B case to actually enable CH0 clock buffers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These should make it possible to feed port C from pipe A or port B from
pipe B. Didn't quite seem to work though.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CHV, All the freq request should be even. So, we need to make sure we
request the opcode accordingly.
v2: Avoid vairable for freq request (ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV uses the gen8 shadow register mechanism so we shouldn't be
checking the GT FIFO status.
This effectively removes the posting read, so add an explicit
posting read using FORCEWAKE_ACK_VLV (which is what use in
vlv_forcewake_reset()).
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skip __gen6_gt_wait_for_thread_c0() on CHV.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Disable media turbo and Add DOWN_IDLE_AVG support (Ville)
v3: Mass rename of the dev_priv->rps variables in upstream.
v4: Rebase against latest code. (Deepak)
v5: Rebase against latest nightly code. (Deepak)
v6: Rename the variables to match the spec (Mika)
v7: change min/max freq variable naming to match spec (Mika)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because of the upcoming vblank interrupt driven watermark update
mechanism we will have use for vblank interrupts during plane
enabling/disabling. So don't call drm_vblank_off() until planes
are off, and call drm_vblank_on() just before we start to enable
the planes.
v2: Pimp commit message (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Support to individually control Media/Render well based on the register access.
Add CHV specific write function to habdle difference between registers
that are sadowed vs those that need forcewake even for writes.
Streamline the CHV forcewake functions just like was done for VLV.
This will also fix a bug in accessing the common well registers,
where we'd end up trying to wake up the wells too many times
since we'd call force_wake_get/put twice per register access, with
FORCEFAKE_ALL both times.
v2: Drop write FIFO for CHV and add comman well forcewake (Ville)
Re-factor CHV/VLV Forcewake offsets (Ben)
v3: Fix for decrementing fw count in chv read/write. (Deepak)
v4: Squash the patches (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[vsyrjala: Move the register range macros into intel_uncore.c]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Configure PCBR if BIOS fails allocate pcbr (deepak)
v3: Fix PCBR condition check during CHV RC6 Enable flag set
v4: Fixup PCBR comment msg. (Chris)
Rebase against latest code (Deak)
Fixup Spurious hunk (Ben)
v5: Fix PCBR and commentis msg (mika)
v6: Rebase patch on latest nightly (Deepak)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"Because our driver assumes only one panel is PSR capable, and we
already have other PSR information on dev_priv instead of intel_dp. If
we ever support multiple PSR panels, we'll have to move struct
i915_psr to intel_dp anyway." (by Paulo)
v2: Avoid more than one setup. Removing initialization
and trusting allocation. (By Paulo Zanoni).
v3: rebase.
v4: Adding comment.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
display rework fixes lots of displayport issues.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (43 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
We were sending the necessary state changes to unset the mode, but
never actually hit the big GO button unless another modeset happens
afterwards.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
SOR_PWR has no effect to power-off DP links, unlike other SOR protocols.
Instead, on the source side, we cut power to the lanes after having put
the sink into D3. Link training takes care of everything required to
bring it back again.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This previously worked for the most part due to userspace doing a
modeset in response to HPD interrupts. This will allow us to
properly handle cases where sync is lost for other reasons, or if
userspace isn't caring.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will, at some point, be used to replace various bits and pieces of
code doing direct bios parsing. For now, it'll just be used for some
DP improvements.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's also provisions to allow a pad to be locked with a specific
routing, for an indefinite period of time. This will be used in
future patches.
The G94+ pad driver will now also power-down pads when not required.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This was a half-finished hack before, just enough to handle the shared
aux/i2c pad thing on G94 and up.
We got lucky with locking etc up until now, as this was (generally) all
protected by the DRM mode_config lock. It's about to become a lot more
likely to hit the races.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ville Syrjälä