Display a verbose warning message when the incorrect PF attempts to
control timestamping for a port to which it was not assigned. This
shouldn't display except in the case of multiple PFs per port. The
primary intent of this message is to help debugging the reason why the
SIOCSHWTSTAMP ioctl has failed, and to help narrow the cause of the
issue.
Change-ID: Ic98798e0c844d98389d4c20e7160ba256f2bc7e8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Remove some break statements that will never get touched.
2. Remove an extra space.
3. Remove a comment for a parameter that doesn't exist
4. Move the assignment of a variable up to get rid of an else case.
Change-ID: I308a4b5ec070b1f0601f13b041ba4375aaad4b06
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
skb_tx_timestamp() does not report software time stamp
if SKBTX_IN_PROGRESS is set. According to timestamping.txt
software time stamps are a fallback and should not be
generated if hardware time stamp is provided.
Move call to skb_tx_timestamp() after setting
SKBTX_IN_PROGRESS.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new API to get the port mac address from firmware.
It also adds support to the ndo_get_phys_port_id() callback to provide
port specific unique id to the netdev layer.
If the adapter has a valid per-port mac address then that
would be used for this purpose and is expected to be unique
on a per-port basis.
The information can be viewed by reading the phys_port_id
attribute in sysfs for each netdev or via IF netlink
interface.
Change-ID: I341fa6fff9c112f1f6d987189309e730e0b50e8b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To maintain the same message structure as netdev_* functions print.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To maintain the same message structure as netdev_* functions print.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One occurance left intact as it's unrelated to net_device.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To maintain the same message structure as netdev_* functions print.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To maintain the same message structure as netdev_* functions print.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several functions left out cause we might not have at that time a valid
bond/slave/port.
Also, converted severa pr_ratelimited into net_ratelimited.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To maintain the same message structure as netdev_* functions print.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converted only the parts where we've had a valid net_device, skipping the
init/deinit and options verification.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instead of return error on zero rx_coalesce_usecs, disable coalesce
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the conversion to "static" functions this one got left out, only its
prototype was converted, thus resulting in:
drivers/net/bonding//bond_options.c:674:5: warning: symbol
'bond_option_mode_set' was not declared. Should it be static?
Fix it by making it static and also break the line in two as it was too
long.
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we exit if the slave isn't the first slave, doesn't support mac
address setting and fail_over_mac isn't FOM_ACTIVE. It's wrong because we
only require ndo_set_mac_address in case bonding is in active-backup mode
and FOM isn't FOM_ACTIVE.
To fix this - only exit with an error if we're in a/b mode and have
fail_over_mac != FOM_ACTIVE.
Also, maintain current behaviour on the first slave (forcibly change fom to
FOM_ACTIVE) to not break anyone's configuration.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a counter rx_noskb_drop for failure to allocate an skb.
Summed the per-channel rx_nodesc_trunc counters earlier so that they can
be included in rx_dropped.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If using a demand-dialled PPP unit for a PPP multilink master, the pppd
daemon needs to reset the sequence counter between two connections. This
allows the daemon to reuse the PPP unit instead of destroying and recreating
it. As there is no API to reset the counter, this patch resets the counter
whenever the SC_MULTILINK flag is set.
Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using __rcu annotation actually helps to spot all accesses to
bond->current_arp_slave are correctly protected, with LOCKDEP support.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RCU was added to bonding in linux-3.12 but lacked proper sparse annotations.
Using __rcu annotation actually helps to spot all accesses to bond->curr_active_slave
are correctly protected, with LOCKDEP support.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
curr_active_slave is rcu protected, and bonding_show_mii_status() only
wants to check if pointer is NULL or not.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only keep bond_option_active_slave_get_rcu() helper.
bond_fill_info() uses a new bond_option_active_slave_get_ifindex()
helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlPE2fYACgkQjTAFq1RaXHNpmwCfY+zM07sxULHpFYoLPEHVbdVh
tXgAoIG6RVra8G8aPEBEk1MeRMAx+HRj
=2is3
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.17-20140715' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2014-07-15
this is a pull request of 4 patches for net-next/master.
Prabhakar Lad contributes a patch that converts the c_can driver to use
the devm api. The remaining four patches by Nikita Edward Baruzdin
improve the SJA1000 driver with loopback testing support and introduce
a new testing mode presume ack, for successful transmission even if no
ACK is received.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of entries in the phy speed/duplex settings
array to support KR and KX mode, the work-around to add/remove
baseT settings to run at a fixed speed is no longer needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the phy speed/duplex settings array to support more
than just baseT features. This change adds entries to support
the following additional speed/duplex/media types:
SUPPORTED_10000baseKR_Full
SUPPORTED_10000baseKX4_Full
SUPPORTED_2500baseX_Full
SUPPORTED_1000baseKX_Full
Additionally, it changes the 10GbE baseT entry from using the
hardcoded value 10000 to the SPEED_10000 define.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit enhances the iwarp driver to optionally keep a log of rdma
work request timining data for kernel mode QPs. If iw_cxgb4 module option
c4iw_wr_log is set to non-zero, each work request is tracked and timing
data maintained in a rolling log that is 4096 entries deep by default.
Module option c4iw_wr_log_size_order allows specifing a log2 size to use
instead of the default order of 12 (4096 entries). Both module options
are read-only and must be passed in at module load time to set them. IE:
modprobe iw_cxgb4 c4iw_wr_log=1 c4iw_wr_log_size_order=10
The timing data is viewable via the iw_cxgb4 debugfs file "wr_log".
Writing anything to this file will clear all the timing data.
Data tracked includes:
- The host time when the work request was posted, just before ringing
the doorbell. The host time when the completion was polled by the
application. This is also the time the log entry is created. The delta
of these two times is the amount of time took processing the work request.
- The qid of the EQ used to post the work request.
- The work request opcode.
- The cqe wr_id field. For sq completions requests this is the swsqe
index. For recv completions this is the MSN of the ingress SEND.
This value can be used to match log entries from this log with firmware
flowc event entries.
- The sge timestamp value just before ringing the doorbell when
posting, the sge timestamp value just after polling the completion,
and CQE.timestamp field from the completion itself. With these three
timestamps we can track the latency from post to poll, and the amount
of time the completion resided in the CQ before being reaped by the
application. With debug firmware, the sge timestamp is also logged by
firmware in its flowc history so that we can compute the latency from
posting the work request until the firmware sees it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ingress WRITE or READ RESPONSE errors, HW provides the offending
stag from the packet. This patch adds logic to log the parsed TPTE
in this case. cxgb4 now exports a function to read a TPTE entry
from adapter memory.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise a larger max read queue depth for qps, and gather the resource limits
from fw and use them to avoid exhaustinq all the resources.
Design:
cxgb4:
Obtain the max_ordird_qp and max_ird_adapter device params from FW
at init time and pass them up to the ULDs when they attach. If these
parameters are not available, due to older firmware, then hard-code
the values based on the known values for older firmware.
iw_cxgb4:
Fix the c4iw_query_device() to report these correct values based on
adapter parameters. ibv_query_device() will always return:
max_qp_rd_atom = max_qp_init_rd_atom = min(module_max, max_ordird_qp)
max_res_rd_atom = max_ird_adapter
Bump up the per qp max module option to 32, allowing it to be increased
by the user up to the device max of max_ordird_qp. 32 seems to be
sufficient to maximize throughput for streaming read benchmarks.
Fail connection setup if the negotiated IRD exhausts the available
adapter ird resources. So the driver will track the amount of ird
resource in use and not send an RI_WR/INIT to FW that would reduce the
available ird resources below zero.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates iw_cxgb4 to determine the Ingress Padding Boundary from
cxgb4_lld_info, and take subsequent actions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This passes down NET_NAME_USER (or NET_NAME_ENUM) to alloc_netdev(),
for any device created over rtnetlink.
v9: restore reverse-christmas-tree order of local variables
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The proper string for this license is "GPL v2", instead of "GPLv2".
This commit fixes that.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SJA1000 has a self test mode (STM) which does not require
acknowledgement for the successful message transmission. In this mode a
node test is possible without any other active node on the bus.
This patch adds a possibility to set STM for SJA1000 controller through
specifying the corresponding CAN_CTRLMODE_PRESUME_ACK netlink flag.
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This adds support for hardware loopback in SJA1000 by utilising its self
reception request (SRR) feature. Upon SRR the message is transmitted and
received simultaneously, meaning you can't have hardware loopback
without actually sending a message to the CAN bus in case of SJA1000.
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch uses devm_* APIs as they are device managed and make code simpler.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the module sends bursts of data, sometimes a deadlock happens in
the hso driver when the tty buffer doesn't get the chance to be flushed
quickly enough.
Remove the endless while loop in function put_rxbuf_data() which is
called by the urb completion handler.
If there isn't enough room in the tty buffer, discards all the data
received in the URB.
Cc: David Miller <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue "retry_unthrottle_workqueue" is not scheduled anywhere
in the code. So, remove it.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the 'foo*' bar with 'foo *bar' and (foo*) with (foo *).
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally any device ids will be above the corresponding device driver
structure. This patch moves the pci device ids and MODULE_DEVICE_TABLE()
above the pci driver structure.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert printk() to netdev_dbg/info/err or dev_info/err/dbg
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace ioremap() with the devm_ioremap() so that
the resource will be freed automatically with the probe failed.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the remove functionalities after the probe
so that we can see the registered and released resources properly.
Every driver follows the same concept.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed to select 40G mode on a 10G/40G capable card.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 568f194e8b ("net: ppp: use
sk_unattached_filter api") causes sk_chk_filter() to be called twice when
setting a PPP pass or active filter. This applies to both the generic PPP
subsystem implemented by drivers/net/ppp/ppp_generic.c and the ISDN PPP
subsystem implemented by drivers/isdn/i4l/isdn_ppp.c. The first call is from
within get_filter(). The second one is through the call chain
ppp_ioctl() or isdn_ppp_ioctl()
--> sk_unattached_filter_create()
--> __sk_prepare_filter()
--> sk_chk_filter()
The first call from within get_filter() should be deleted as get_filter() is
called just before calling sk_unattached_filter_create() later on, which
eventually calls sk_chk_filter() anyway.
For 3.15.x, this proposed change is a bugfix rather than a pure optimization as
in that branch, sk_chk_filter() may replace filter codes by other codes which
are not recognized when executing sk_chk_filter() a second time. So with
3.15.x, if sk_chk_filter() is called twice, the second invocation may yield
EINVAL (this depends on the filter codes found in the filter to be set, but
because the replacement is done for frequently used codes, this is almost
always the case). The net effect is that setting pass and/or active PPP filters
does not work anymore, since sk_unattached_filter_create() always returns
EINVAL due to the second call to sk_chk_filter(), regardless whether the filter
was originally sane or not.
Signed-off-by: Christoph Schulz <develop@kristov.de>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Napi id was not marked for gro_skb, this will lead rx busy loop won't
work correctly since they stack never try to call low latency receive
method because of a zero socket napi id. Fix this by marking napi id
for gro_skb.
The transaction rate of 1 byte netperf tcp_rr gets about 50% increased
(from 20531.68 to 30610.88).
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vxlan driver call common function udp_sock_create to create the
listener UDP port.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Obvious copy/paste error when I converted the ad_select to the new
option API. "lacp_rate" there should be "ad_select" so we can get the
proper value.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Fixes: 9e5f5eebe7 ("bonding: convert ad_select to use the new option
API")
Reported-by: Karim Scheik <karim.scheik@prisma-solutions.at>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPP channel MTU is used with Multilink PPP when ppp_mp_explode() (see
ppp_generic module) tries to determine how big a fragment might be. According
to RFC 1661, the MTU excludes the 2-byte PPP protocol field, see the
corresponding comment and code in ppp_mp_explode():
/*
* hdrlen includes the 2-byte PPP protocol field, but the
* MTU counts only the payload excluding the protocol field.
* (RFC1661 Section 2)
*/
mtu = pch->chan->mtu - (hdrlen - 2);
However, the pppoe module *does* include the PPP protocol field in the channel
MTU, which is wrong as it causes the PPP payload to be 1-2 bytes too big under
certain circumstances (one byte if PPP protocol compression is used, two
otherwise), causing the generated Ethernet packets to be dropped. So the pppoe
module has to subtract two bytes from the channel MTU. This error only
manifests itself when using Multilink PPP, as otherwise the channel MTU is not
used anywhere.
In the following, I will describe how to reproduce this bug. We configure two
pppd instances for multilink PPP over two PPPoE links, say eth2 and eth3, with
a MTU of 1492 bytes for each link and a MRRU of 2976 bytes. (This MRRU is
computed by adding the two link MTUs and subtracting the MP header twice, which
is 4 bytes long.) The necessary pppd statements on both sides are "multilink
mtu 1492 mru 1492 mrru 2976". On the client side, we additionally need "plugin
rp-pppoe.so eth2" and "plugin rp-pppoe.so eth3", respectively; on the server
side, we additionally need to start two pppoe-server instances to be able to
establish two PPPoE sessions, one over eth2 and one over eth3. We set the MTU
of the PPP network interface to the MRRU (2976) on both sides of the connection
in order to make use of the higher bandwidth. (If we didn't do that, IP
fragmentation would kick in, which we want to avoid.)
Now we send a ICMPv4 echo request with a payload of 2948 bytes from client to
server over the PPP link. This results in the following network packet:
2948 (echo payload)
+ 8 (ICMPv4 header)
+ 20 (IPv4 header)
---------------------
2976 (PPP payload)
These 2976 bytes do not exceed the MTU of the PPP network interface, so the
IP packet is not fragmented. Now the multilink PPP code in ppp_mp_explode()
prepends one protocol byte (0x21 for IPv4), making the packet one byte bigger
than the negotiated MRRU. So this packet would have to be divided in three
fragments. But this does not happen as each link MTU is assumed to be two bytes
larger. So this packet is diveded into two fragments only, one of size 1489 and
one of size 1488. Now we have for that bigger fragment:
1489 (PPP payload)
+ 4 (MP header)
+ 2 (PPP protocol field for the MP payload (0x3d))
+ 6 (PPPoE header)
--------------------------
1501 (Ethernet payload)
This packet exceeds the link MTU and is discarded.
If one configures the link MTU on the client side to 1501, one can see the
discarded Ethernet frames with tcpdump running on the client. A
ping -s 2948 -c 1 192.168.15.254
leads to the smaller fragment that is correctly received on the server side:
(tcpdump -vvvne -i eth3 pppoes and ppp proto 0x3d)
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x3] MLPPP (0x003d), length 1494: seq 0x000,
Flags [end], length 1492
and to the bigger fragment that is not received on the server side:
(tcpdump -vvvne -i eth2 pppoes and ppp proto 0x3d)
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
length 1515: PPPoE [ses 0x5] MLPPP (0x003d), length 1495: seq 0x000,
Flags [begin], length 1493
With the patch below, we correctly obtain three fragments:
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
Flags [begin], length 1492
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
Flags [none], length 1492
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 27: PPPoE [ses 0x1] MLPPP (0x003d), length 7: seq 0x000,
Flags [end], length 5
And the ICMPv4 echo request is successfully received at the server side:
IP (tos 0x0, ttl 64, id 21925, offset 0, flags [DF], proto ICMP (1),
length 2976)
192.168.222.2 > 192.168.15.254: ICMP echo request, id 30530, seq 0,
length 2956
The bug was introduced in commit c9aa689537
("[PPPOE]: Advertise PPPoE MTU") from the very beginning. This patch applies
to 3.10 upwards but the fix can be applied (with minor modifications) to
kernels as old as 2.6.32.
Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_MODE_EN bit was defined to 0, while it is actually 6. It was not
much of a problem on older designs where this was a no-op, and the RGMII
data-path would always be enabled, but newer GENET controllers need to
explicitely enable their RGMII data-pad using this bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of updates intended for the 3.17 stream...
This is primarily a Bluetooth pull. Gustavo says:
"A lot of patches to 3.17. The bulk of changes here are for LE support.
The 6loWPAN over Bluetooth now has it own module, we also have support for
background auto-connection and passive scanning, Bluetooth device address
provisioning, support for reading Bluetooth clock values and LE connection
parameters plus many many fixes."
The balance is just a pull of the wireless.git tree, to avoid some
pending merge problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The transport offset of the IPv4 packet should be fixed and wouldn't
be out of the hw limitation, so the r8152_csum_workaround() should
be used for IPv6 packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first
time it is armed, ocassionally we have observed that the EQ doesn't raise
anymore interrupts even if it is in armed state.
This patch fixes this by setting the clear-interrupt bit when EQs are
armed for the first time in be_open().
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the IPv6 hw checksum for RTL8111C and later chips. Note
that the hw has the limitation for the transport offset. The
checksum must be calculated by sw, when the transport offset is
out of the range which the hw accepts.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace large send with giant send for TSO for RTL8111C and later ICs.
The large send setting of the RTL8111DP is different from the other
chips. However, the giant send setting is the same for all the chips
which support it. Use the giant send to synchronize the settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the txd_version, split rtl8169_tso_csum() into
rtl8169_tso_csum_v1() and rtl8169_tso_csum_v2().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Event timestamp values should be adjusted by 3*reference clock period +
11 ns = 35 ns to compensate for input path and synchronization delays.
So subtract 35ns from event timestamps.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several issues in fst_add_one() and fst_init_card():
- invalid pointer dereference at card->ports[card->nports - 1] if
register_hdlc_device() fails for the first port in fst_init_card();
- fst_card_array overflow at fst_card_array[no_of_cards_added]
because there is no checks for array overflow;
- use after free because pointer to deallocated card is left in fst_card_array
if something fails after fst_card_array[no_of_cards_added] = card;
- several leaks on failure paths in fst_add_one().
The patch fixes all the issues and makes code more readable.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a new network driver for the network controller in Marvell
Armada 375 SoC.
Given the controller is very different from the ones in the other Marvell
SoCs that use the mv643xx_eth (Kirkwood, Orion, Discovery) and mvneta
(Armada 370/38x/XP) drivers, a new driver is needed.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
[Ezequiel: coding style cleanup]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the debug message format. This patch changes to the
commit f160a2d0b524eeebd97a68e2fbb59fad4cdd3fee: net: cpmac: dynamic debug fixes
When we use pr_debug()/netdev_dbg() new lines are inserting in b/w
the values. The format when i use the printk()
These formats used in skb dump and reg dump. This functions
called from the entire code. So this will be enabled all the lines.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
To properly re-initialize SR-IOV it is necessary to reset the device
even if it is already down. Not doing this may result in Tx unit hangs.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping a bridge fdb dumps every fdb entry
held. With this change we are going to filter
on selected bridge port.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some devices, the internal PLL circuit occasionally provides the
wrong clock frequency after power up. The probability of failure is less
than one failure per 1000 power cycles. When the failure occurs, the
internal clock frequency is around 1/20 of the correct frequency.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc95xx needs to resume with reset operation. Otherwise it causes
system hang by network error like below after resume. This case appears
on odroid u3 board.
[ 9.727600] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727648] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727689] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.727728] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 9.729486] PM: resume of devices complete after 2011.219 msecs
[ 10.117609] Restarting tasks ... done.
[ 11.725099] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.480846] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
[ 13.481361] smsc95xx 1-2:1.0 eth0: kevent 2 may have been dropped
...
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum jumbo frame size for RTL8153 is 9K bytes.
Change the max rx packet size to 9K.
Change the use of the shared fifo from 6K (default) to 12K for tx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
before registering the the net device this code freeing net device
by using the label 'fail'
fixed by introducing an another label 'out'
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch insert proper spaces before return statement.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes to style of declarattion which follows every driver
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does the following changes
1. convert printk(KERN_DEBUG.. to netdev_dbg() if we have net_device object
or convert to dev_dbg() if we have device object.
2. convert printk(KERN_WARNING.. to netdev_warn() if we have net_device object
or convert to dev_warn() if we have device object
3. convert printk() to pr_*
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch convert the normal comments to networking subsystem
style comments.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the space after '#' in macro defination
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged two uses of kzalloc() for allocating and zeroing
arrays, use kcalloc() instead as recommended.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl flagged a bunch of: "CHECK: Alignment should match open
parenthesis" problems, fix all of them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently status frames are only handled when packet timestamping is
enabled, but status frames are also needed for pin event timestamping.
Fix by moving packet timestamping check to after status frame decode.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlx5_core_destroy_mkey(), we must first remove the mr from the
radix tree and then destroy it. Otherwise we might hit a race if the
key was reallocated and we attempted to insert it to the radix tree.
Also handle radix tree insert/delete failures.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Eli Cohen <elic@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In order to have at least a netconsole to debug kernel issues on
Windows Azure this patch implements netpoll support.
Sending packets is easy, netvsc_start_xmit() does already everything
needed.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer to the struct net_device in the private data is only
assigned but never used, so delete it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
arc_emac_priv, use stats from struct net_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8411, RTL8111G, RTL8402, RTL8105, and RTL8106, disable the feature
of entering the L2/L3 link state of the PCIe. When the nic starts the process
of entering the L2/L3 link state and the PCI reset occurs before the work
is finished, the work would be queued and continue after the next the PCI
reset occurs. This causes the device stays in L2/L3 link state, and the system
couldn't find the device.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend and phy_resume are two commonly used helper functions that
need to be exported for Ethernet drivers to be built as modules
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both transmit and receive use the same infrastructure for calculating
the packet timestamp. Rather than duplicating the code, provide a
function to do this common work. Model this function in the Intel
e1000e version which avoids calling ns_to_ktime() within the spinlock;
the spinlock is critical for timecounter_cyc2time() but not
ns_to_ktime().
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless status check in the transmit reap path - we have
already checked that the BD_ENET_TX_READY bit is clear, and as the
hardware only ever clears this bit, there is no way this test can ever
be true.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we timeout on transmit, it would be useful to dump the transmit
ring, so we can see the ring state. This can be helpful to diagnose
the cause of transmit timeouts.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to merge two separate preprocessor conditionals together.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.
The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of "better implementation of iMX6 ERR006358 quirk", we no longer have
a requirement for a delayed work. Moreover, the work is now only used
for timeout purposes, so the timeout flag is also pointless - we set it
each time we queue the work, and the work clears it.
Replace the fec_enet_delayed_work struct with a standard work_struct,
resulting in simplified timeout handling code.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a (delayed) workqueue for ERR006358 is not correct - a work queue
is a single-trigger device. Once the work queue has been scheduled, it
can't be re-scheduled until it has been run. This can cause problems -
with an appropriate packet timing, we can end up with packets queued,
but not sent by the hardware, resulting in the transmit timeout firing.
Re-implement this as per the workaround detailed in the ERR006358
documentation - if there are packets waiting to be sent when we service
the transmit ring, and we see that the transmitter is not running,
kick the transmitter to run the pending entries in the ring.
Testing here with a 10Mbit half duplex link sees the resulting iperf
TCP bandwidth increase from between 1 to 2Mbps to between 8 to 9Mbps.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes the command value generated for CSUM calculation
when running in big endian mode. The Ethernet protocol ID for IP was
being unconditionally byte-swapped in the layer 3 protocol check (with
swab16), which caused the mvneta driver to not function correctly in
big endian mode. This patch byte-swaps the ID conditionally with
htons.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds debugfs capabilities to netback. There used to be a similar
patch floating around for classic kernel, but it used procfs. It is based on a
very similar blkback patch.
It creates xen-netback/[vifname]/io_ring_q[queueno] files, reading them output
various ring variables etc. Writing "kick" into it imitates an interrupt
happened, it can be useful to check whether the ring is just stalled due to a
missed interrupt.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Many places call fec_restart() with the second parameter being some kind
of previously saved duplex value, but only two places call it with some
other setting. This is at odds with how the other link settings are
handled, and used to be racy before the rtnl locks were added to
fec_restart()'s various call paths.
Clean this up so all link capabilities are handled in the same way -
saved into the fec_enet_private structure, and then fec_restart() acts
on those settings.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link goes down, the adjust_link method will be called, but
there is no synchronisation to ensure that we won't be processing some
last remaining packets via the NAPI handlers while performing a reset of
the device.
Add the necessary synchronisation to ensure that packet processing
is complete before we stop and reset the FEC.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the features (receive checksumming) requires the hardware to be
reprogrammed, and also changes the checks in the receive packet
processing.
The current implementation has a race - fec_set_features() changes the
flags which alter the receive packet processing while the adapter is
active, and potentially receiving frames. Only after we've modified
the software flag do we shutdown and reconfigure the hardware.
This can lead to packets being received and marked with a valid checksum
(via CHECKSUM_UNNECESSARY) when the hardware checksum validation has not
yet been enabled.
We must quiesce the device, then change the software configuration for
this feature, and then resume the device if it was previously running.
The resulting code structure also allows us to add other configuration
features in this path without having to quiesce and resume the network
interface and device.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_set_features() calls fec_stop() to stop the transmit ring while the
transmit queue is still active. This can lead to the transmit ring
being restarted by an intervening packet queued for transmission, or
by the tx quirk timer expiring.
Fix this by disabling NAPI (which ensures that the NAPI handlers are
not running), and then take the transmit lock while we stop and
restart the adapter (which prevents new packets being queued).
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_suspend() calls fec_stop() to stop the transmit ring while the
transmit packet processing is still active. This can lead to the
transmit queue being restarted by an intervening packet queued for
transmission, or by the tx quirk timer expiring.
Fix this by disabling NAPI first, which will ensure that the NAPI
handlers are not running. Then, take the transmit lock before
detaching the netif device. This ensures that there are no races
with the transmit path - and also ensures that the watchdog won't
fire.
We can then safely stop the ethernet device itself, knowing that the
rest of the driver is safely shut down.
On resume, we bring the device back up in reverse order - we restart
the device, reattach the device (under the tx lock), and then enable
the NAPI handlers.
We also need to adjust the close function to cope with this new
sequence, so that it's possible to cleanly close down the driver
after the hardware fails to resume (eg, due to the regulator_enable()
or pinctrl calls in the resume path returning an error.)
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second stage to "move calls to quiesce/resume packet
processing out of fec_restart()", where we remove calls which are not
appropriate to the call site.
In the majority of cases, there is no need to detach and reattach the
interface as we are holding the queue xmit lock across the reset. The
exception to that is in fec_resume(), where we are already detached by
the suspend function. Here, we can remove the call to detach the
interface.
We also do not need to stop the transmit queue. Holding the xmit lock
is enough to ensure that the transmit packet processing is not running
while we perform our task. However, since fec_restart() always cleans
the rings, we call netif_wake_queue() (or netif_device_attach() in the
case of resume) just before dropping the xmit lock. This prevents the
watchdog firing.
Lastly, always call napi_enable() after the device has been reattached
in the resume path so that we know that the transmit packet processing
is already in an enabled state, so we don't call netif_wake_queue()
while detached.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the calls to quiesce and resume packet processing out of
fec_restart() to its call sites. This is the first step in a two stage
clean up of this code, where we just move the calls out of fec_restart()
without changing them. Not everywhere needs to issue these calls, and
not everywhere needs all of these calls to be issued.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling fec_restart() or fec_stop() while the device is down
or not present (iow suspended.)
Although the ndo_timeout method will only be called if the device is
present and running, we defer this to a work queue. The work queue
can run independently, and so needs to repeat these checks to ensure
that a restart doesn't occur after the device has been taken down or
detached for suspend. In this case, we call fec_restart() in the
resume path, so nothing is lost.
For fec_set_features, we add a call to fec_restart() in fec_enet_open()
to ensure that the hardware is appropriate programmed when the interface
is opened. fec_set_features() call should not occur while we're
suspended, so we don't have to worry about that case.
The adjust_link needs similar treatment - this also is called from a
work queue, which may be run independently after we have taken the
device down and detached it. In this case, we just mark the link
down and take no further action. We will reset things appropriately
once the device is up and running again, at which point we will receive
another adjust_link callback.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FEC is suspended, the device is detached. Upon resume failure,
the device is left in detached mode, possibly with some of the required
clocks not running. We don't want to be poking the device in that state
because as it may cause bus errors.
If the device is marked detached, avoid calling fec_stop().
This depends upon: "net:fec: improve safety of suspend/resume paths"
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should hold the rtnl lock while suspending, resuming or processing
the transmit timeout to ensure that nothing will interfere while we
bring up, take down or restart the hardware. The transmit timeout
could run if we're preempted during suspend.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Maggie Mae Roxas, the mvneta driver doesn't behave
properly in 10 Mbit/s mode. This is due to a misconfiguration of the
MVNETA_GMAC_AUTONEG_CONFIG register: bit MVNETA_GMAC_CONFIG_MII_SPEED
must be set for a 100 Mbit/s speed, but cleared for a 10 Mbit/s speed,
which the driver was not properly doing. This commit adjusts that by
setting the MVNETA_GMAC_CONFIG_MII_SPEED bit only in 100 Mbit/s mode,
and relying on the fact that all the speed related bits of this
register are cleared at the beginning of the mvneta_adjust_link()
function.
This problem exists since c5aff18204 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") which is the commit that
introduced the mvneta driver in the kernel.
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Reported-by: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Cc: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is recommended that TX work not count against the quota.
The cost of TX packet liberation is a minute percentage of what it costs to
process an RX frame. Furthermore, that SKB freeing makes memory available for
other paths in the stack.
Give the TX a larger budget and be more aggressive about cleaning up the Tx
descriptors this budget could be changed using ethtool:
$ ethtool -C eth1 tx-frames-irq <budget>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a local copy of dev_addr in mlx4_en_set_mac() to prevent dev_addr
from being modified during error flow or when dev_addr is modified in
another context (which is another problem that is being discussed over
the mailing list [1]).
Also fixing bad naming of priv->prev_mac into priv->current_mac.
[1] - http://patchwork.ozlabs.org/patch/351489/
Reviewed-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LLC/SNAP 8 bytes should not be added as part of header calculation.
If used, payload will be decreased accordingly. For MTU of 1500
we'll set 1522 instead of 1523.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Liran Liss <liranl@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Promiscous mode is only for MACs.
Should not disable/enable VLAN filter when entering/leaving promisuous mode.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify port number to avoid crashes if port number is outside the range.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback can't work when port is down.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 40GE we can't use the default bw units for set ratelimit (100 Mbps)
since the max is 255*100 Mbps = 25 Gbps (not suited for 40GE), thus we need 1 Gbps units.
But for 10GE 1 Gbps units might be too bruit so we use the following solution.
For user set ratelimit <= 25 Gbps:
use 100 Mbps units * user_ratelimit (* 10).
For user set ratelimit > 25 Gbps:
use 1 Gbps units * user_ratelimit.
For user set unlimited ratelimit (0 Gbps):
use 1 Gbps units * MAX_RATELIMIT_DEFAULT (57)
Note: any value > 58 will damage the FW ratelimit computation, so we allow
a max and any higher value will be pulled down to 57.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device should be waked up from runtime suspend before dumping
the hw counter.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes issues with debug printk calls across the driver, normally
disabled; first compilation errors:
drivers/net/fddi/defxx.c:676:1: error: pasting "(" and ""In dfx_bus_init...\n"" does not give a valid preprocessing token
drivers/net/fddi/defxx.c:820:1: error: pasting "(" and ""In dfx_bus_uninit...\n"" does not give a valid preprocessing token
and so on, and then warnings:
drivers/net/fddi/defxx.c: In function 'dfx_driver_init':
drivers/net/fddi/defxx.c:1132: warning: format '%0X' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
drivers/net/fddi/defxx.c:1132: warning: format '%0X' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
etc. Additionally casts are removed from virtual addresses and %p used.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds DMA synchronisation calls needed in the receive path:
1. To retrieve the Receive Status word that is prepended by the PDQ DMA
engine in the receive buffer, and provides information about the
frame received, including its size and any errors.
2. To make data received available for copying in the small-frame case
(size <= SKBUFF_RX_COPYBREAK) where the original DMA buffer will be
returned to the receive descriptor ring and therefore its mapping
retained.
With DMA mapping error handling in place, added by the other patch,
this may now also trigger where an attempt to map a newly allocated
buffer for DMA has failed. In that case data from the original buffer
will be copied out and the buffer returned to the DMA descriptor ring.
These calls may do nothing when data is in the host DMA addressing range
of the FDDI interface, such as always on 32-bit systems, however their
absence makes frame reception stop functioning reliably on systems that
have memory beyond the low 4GB of the address space.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds error handling for DMA mapping requests; I think there isn't
much else to say about it.
A good side-effect is the mapping in the transmit path is now made with
the board lock released. Also if DMA mapping fails for a newly
allocated receive buffer, then data from the old buffer will be copied
out (as is presently done for small frames only whose size does not
exceed SKBUFF_RX_COPYBREAK) and the original buffer returned, with its
mapping unchanged, to the DMA descriptor ring.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the two remaining places across the driver that use dev_alloc_skb
to netdev_alloc_skb. Another place has already been converted to use
__netdev_alloc_skb, no idea why these two have been left behind.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prearranged receive DMA bounce buffer mappings are not released in the
card reboot/shutdown path. That does not affect frame reception, but
probably explains the random segmentation fault I observed the other day
on interface shutdown. Card is rebooted as required by the spec in the
process of ring fault recovery when a PC Trace signal has been received.
This change fixes the problem in an obvious manner.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive DMA maps are oversized, they include EISA legacy 128-byte
alignment padding in size calculation whereas this padding is never used
for data. Worse yet, if the skb's data area has been realigned indeed,
then data beyond the end of the buffer will be synchronised from the
receive DMA bounce buffer, possibly corrupting data structures residing
in memory beyond the actual end of this data buffer.
Therefore switch to using PI_RCV_DATA_K_SIZE_MAX rather than NEW_SKB_SIZE
in DMA mapping, the value the former macro expands to is written to the
receive ring DMA descriptor of the PDQ DMA chip and determines the
maximum amount of data PDQ will ever transfer to the corresponding data
buffer, including all headers and padding.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-07-03
Please pull this first batch of wireless updates intended for the
3.17 stream...
For the mac80211 bits, Johannes says:
"The biggest thing here is probably Arik's TDLS rework, beyond that we
have smaller improvements and features like David's scanning IE thing,
Luca's queue work, some CSA work, etc. Also your PID rate control
removal, of course."
For the iwlwifi bits, Emmanuel says:
"I have here a whole bunch of various things. Andy contributes
better debug prints for dvm specific flows and a module parameter to
completely disable power save for dvm. Andrei is sharing the premises
of his work on CSA - more to come. Eran and Liad keep on working
on the new devices. I have the regular amount of BT Coex stuff and
I continue to work on the firmware error report system adding more
debug capabilities. More to come on that subject too."
On top of that, there are some cleanups to the new rsi driver, some
continuing improvements to the rtl818x drivers, and the usual bundles
of updates to ath9k, b43, mwifiex, wil6210, and a few other bits here
and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes compiler warnings:
drivers/net/ethernet/amd/declance.c: In function 'lance_init_ring':
drivers/net/ethernet/amd/declance.c:478: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:487: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:503: warning: cast from pointer to integer of different size
drivers/net/ethernet/amd/declance.c:520: warning: cast from pointer to integer of different size
in 64-bit compilation. Where the value printed is an offset (whose range
will always fit) the cast uses a 32-bit type, otherwise, where it is a
host memory address, the pointer is output directly with %p. Also the
remaining `0x' prefix is dropped for consistency across these messages.
Tested with both 32-bit and 64-bit compilation, as well as at the run time
(with the debug messages affected enabled).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the system is too busy to complete the urb, the tx timout function
would be called. This causes the other tx urbs would be killed, too.
Increase the tx timeout to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In xennet_disconnect_backend(), netif_carrier_off() was called once
per queue when it needs to only be called once.
The queue locking around the netif_carrier_off() call looked very
odd. I think they were supposed to synchronize any NAPI instances with
the expectation that no further NAPI instances would be scheduled
because of the carrier being off (see the check in
xennet_rx_interrupt()). But I can't easily tell if this works
correctly.
Instead, add a napi_synchronize() call after disabling the interrupts.
This is obviously correct as with no Rx interrupts, no further NAPI
instances will be scheduled.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nesting of the per-queue rx_lock and tx_lock in xennet_connect()
is confusing to both humans and lockdep. The locking is safe because
this is the only place where the locks are nested in this way but
lockdep still warns.
Instead of adding the missing lockdep annotations, refactor the
locking to avoid the confusing nesting. This is still safe, because
the xenbus connection state changes are all serialized by the xenwatch
thread.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
The add_vxlan_port ndo driver code was wrongly testing whether HW vxlan offloads
are supported by the device instead of checking if they are currently enabled.
This causes the driver to configure the HW parser to conduct matching for vxlan
packets but since no steering rules were set, vxlan packets are dropped on RX.
Fix that by doing the right test, as done in the del_vxlan_port ndo handler.
Fixes: 1b136de ('net/mlx4: Implement vxlan ndo calls')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default cache operations for ARM64 were changed during 3.15.
To use coherent operations a "dma-coherent" device tree property
is required. If that property is not present in the device tree
node then the non-coherent operations are assigned for the device.
Add support to the amd-xgbe driver to assign the AXI DMA cache settings
based on whether the "dma-coherent" property is present in the device
node. If present, use settings that work with the caches. If not
present, use settings that do not look at the caches.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides some general performance enhancements for the
driver:
- Modify the default coalescing settings (reduce usec, increase frames)
- Change the AXI burst length to 256 bytes (default was 16 bytes which
was smaller than a cache line)
- Change the AXI cache settings to write-back/write-allocate which
allocate cache entries for received packets during the DMA since the
packet will be processed soon afterwards
- Combine ioread/iowrite when disabling both the Tx and Rx interrupts
- Change to processing the Tx/Rx channels in pairs
- Only recycle the Rx descriptors when a threshold of dirty descriptors
is reached
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the napi context is added using netif_napi_add each time
the ndo_open operation is called. However, there is not a
corresponding netif_napi_del call during the ndo_stop operation. If
the device ndo_open operation was called more than once an infinite
loop occurs during module unload. Add a call to netif_napi_del during
the ndo_stop operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing the MTL interrupts the interrupt status
register is written to instead of the interrupt enable register.
Since no MTL interrupts are being enabled and the default state
is for MTL interrupts to be disabled this did not cause a problem,
but needs to be fixed to target the correct register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial change from sscanf to kstrtouint broke backward
compatbility by using a base of "0" in the kstrtouint call.
This allowed for entering decimal, hexadecimal or octal as
input where previously the sscanf always interpreted the input
as hexadecimal. Additionally, -EIO was returned on error prior
to this change and now it is whatever the error value that is
returned by kstrtouint.
Change the base value of the kstrtouint from 0 to 16 and return
-EIO on error.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic_set_coalesce() has two problems.
* It should return -EINVAL and not -EOPNOTSUPP for invalid coalesce values.
* In case of MSIX, enic_set_coalesce return error after applying requested
coalescing setting partially. We should either apply all the setting requeste
and return success or apply non and return error.
* This patch also simplifies the algo.
This was introduced by
'7c2ce6e60f703 enic: Add support for adaptive interrupt coalescing'
These changes were suggested by Ben Hutchings here
http://www.spinics.net/lists/netdev/msg283972.html
Also change enic driver version.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings are no longer relevant. Even when last slave is
removed, there is a valid address assigned to bond (random).
The correct functionality of vlans is ensured by maintaining unicast
list in vlan_sync_address().
Suggested-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller