NXP Layerscape (ls1028a, ls2088a), dra7xxx and imx6 platforms are either
programmed or statically configured to forward the error triggered by a
link-down state (eg no connected endpoint device) on the system bus for
PCI configuration transactions; these errors are reported as an SError
at system level, which is fatal.
Enumerating a PCI tree when the PCIe link is down is not sensible
either, so even if the link-up check is racy (link can go down after
map_bus() is called) add a link-up check in map_bus() to prevent issuing
configuration transactions when the link is down.
SError report:
SError Interrupt on CPU2, code 0xbf000002 -- SError
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc5-next-20200914-00001-gf965d3ec86fa #67
Hardware name: LS1046A RDB Board (DT)
pstate: 20000085 (nzCv daIf -PAN -UAO BTYPE=--)
pc : pci_generic_config_read+0x3c/0xe0
lr : pci_generic_config_read+0x24/0xe0
sp : ffff80001003b7b0
x29: ffff80001003b7b0 x28: ffff80001003ba74
x27: ffff000971d96800 x26: ffff00096e77e0a8
x25: ffff80001003b874 x24: ffff80001003b924
x23: 0000000000000004 x22: 0000000000000000
x21: 0000000000000000 x20: ffff80001003b874
x19: 0000000000000004 x18: ffffffffffffffff
x17: 00000000000000c0 x16: fffffe0025981840
x15: ffffb94c75b69948 x14: 62203a383634203a
x13: 666e6f635f726568 x12: 202c31203d207265
x11: 626d756e3e2d7375 x10: 656877202c307830
x9 : 203d206e66766564 x8 : 0000000000000908
x7 : 0000000000000908 x6 : ffff800010900000
x5 : ffff00096e77e080 x4 : 0000000000000000
x3 : 0000000000000003 x2 : 84fa3440ff7e7000
x1 : 0000000000000000 x0 : ffff800010034000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc5-next-20200914-00001-gf965d3ec86fa #67
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x1c0
show_stack+0x18/0x28
dump_stack+0xd8/0x134
panic+0x180/0x398
add_taint+0x0/0xb0
arm64_serror_panic+0x78/0x88
do_serror+0x68/0x180
el1_error+0x84/0x100
pci_generic_config_read+0x3c/0xe0
dw_pcie_rd_other_conf+0x78/0x110
pci_bus_read_config_dword+0x88/0xe8
pci_bus_generic_read_dev_vendor_id+0x30/0x1b0
pci_bus_read_dev_vendor_id+0x4c/0x78
pci_scan_single_device+0x80/0x100
Link: https://lore.kernel.org/r/20200916054130.8685-1-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log, remove Fixes tag]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get
wrong, as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception of
the last "obviously correct" patch that updated a FALLTHROUGH comment
that got merged last weekend.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
Y7F+o2p8DiuLLQamdEyB
=lHr1
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl+FqrsTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXnN8B/4sRg7j9OTzVBlDiXF2vj6vbuplTIH6
JR6S5f4PNjUg4gV6ghzSnsx1zqNhPSOr78zDqYto8vv+wqqj3thmld8+gAnSbKtt
yoAa7mhbbN1ryJiwPlZzvX4ApzGZPC7byqEi3+zPIcag6TEl8eyYJOmvY3x1zv8x
CsAb57oCC4erD0n4xlTyfuc8TLpO+EiU53PXbR9AovKQHe4m2/8LWyEbmrm5cRUR
gx8RxoLkkrqK0unzcmanbm47QodiaOTUpycs3IvaBeWZQsqSgFZdI1RAdTZNg+U+
GT8eMRXAwpgDpilPm/0n1O0PKGAsVh9Lbw8Btb/ggqnjTUlA4Z3Df23E
=Wy5n
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Wei Liu:
- a series from Boqun Feng to support page size larger than 4K
- a few miscellaneous clean-ups
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: clocksource: Add notrace attribute to read_hv_sched_clock_*() functions
x86/hyperv: Remove aliases with X64 in their name
PCI: hv: Document missing hv_pci_protocol_negotiation() parameter
scsi: storvsc: Support PAGE_SIZE larger than 4K
Driver: hv: util: Use VMBUS_RING_SIZE() for ringbuffer sizes
HID: hyperv: Use VMBUS_RING_SIZE() for ringbuffer sizes
Input: hyperv-keyboard: Use VMBUS_RING_SIZE() for ringbuffer sizes
hv_netvsc: Use HV_HYP_PAGE_SIZE for Hyper-V communication
hv: hyperv.h: Introduce some hvpfn helper functions
Drivers: hv: vmbus: Move virt_to_hvpfn() to hyperv header
Drivers: hv: Use HV_HYP_PAGE in hv_synic_enable_regs()
Drivers: hv: vmbus: Introduce types of GPADL
Drivers: hv: vmbus: Move __vmbus_open()
Drivers: hv: vmbus: Always use HV_HYP_PAGE_SIZE for gpadl
drivers: hv: remove cast from hyperv_die_event
Currently, dw_pcie_msi_init() allocates and maps page for msi, then
program the PCIE_MSI_ADDR_LO and PCIE_MSI_ADDR_HI. The Root Complex
may lose power during suspend-to-RAM, so when we resume, we want to
redo the latter but not the former. If designware based driver (for
example, pcie-tegra194.c) calls dw_pcie_msi_init() in resume path, the
msi page will be leaked.
As pointed out by Rob and Ard, there's no need to allocate a page for
the MSI address, we could use an address in the driver data.
To avoid map the MSI msg again during resume, we move the map MSI msg
from dw_pcie_msi_init() to dw_pcie_host_init().
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201009155505.5a580ef5@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
If MSI is disabled, there's no need to program PCIE_MSI_INTR0_MASK
and PCIE_MSI_INTR0_ENABLE registers.
Link: https://lore.kernel.org/r/20201009155436.27e67238@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
After applying "PCI: dwc: Add common iATU register support",
there is no need to set own iATU in the Keystone driver itself.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-5-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
This gets iATU register area from reg property that has reg-names "atu".
In Synopsys DWC version 4.80 or later, since iATU register area is
separated from core register area, this area is necessary to get from
DT independently.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-4-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
devices which require non-PCI based MSI handling.
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which allows
to utilize the full functionality of hierarchical irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the irqdomain
which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch and
let the last few users select it.
-----BEGIN PGP SIGNATURE-----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=JlqV
-----END PGP SIGNATURE-----
Merge tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 irq updates from Thomas Gleixner:
"Surgery of the MSI interrupt handling to prepare the support of
upcoming devices which require non-PCI based MSI handling:
- Cleanup historical leftovers all over the place
- Rework the code to utilize more core functionality
- Wrap XEN PCI/MSI interrupts into an irqdomain to make irqdomain
assignment to PCI devices possible.
- Assign irqdomains to PCI devices at initialization time which
allows to utilize the full functionality of hierarchical
irqdomains.
- Remove arch_.*_msi_irq() functions from X86 and utilize the
irqdomain which is assigned to the device for interrupt management.
- Make the arch_.*_msi_irq() support conditional on a config switch
and let the last few users select it"
* tag 'x86-irq-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
PCI: MSI: Fix Kconfig dependencies for PCI_MSI_ARCH_FALLBACKS
x86/apic/msi: Unbreak DMAR and HPET MSI
iommu/amd: Remove domain search for PCI/MSI
iommu/vt-d: Remove domain search for PCI/MSI[X]
x86/irq: Make most MSI ops XEN private
x86/irq: Cleanup the arch_*_msi_irqs() leftovers
PCI/MSI: Make arch_.*_msi_irq[s] fallbacks selectable
x86/pci: Set default irq domain in pcibios_add_device()
iommm/amd: Store irq domain in struct device
iommm/vt-d: Store irq domain in struct device
x86/xen: Wrap XEN MSI management into irqdomain
irqdomain/msi: Allow to override msi_domain_alloc/free_irqs()
x86/xen: Consolidate XEN-MSI init
x86/xen: Rework MSI teardown
x86/xen: Make xen_msi_init() static and rename it to xen_hvm_msi_init()
PCI/MSI: Provide pci_dev_has_special_msi_domain() helper
PCI_vmd_Mark_VMD_irqdomain_with_DOMAIN_BUS_VMD_MSI
irqdomain/msi: Provide DOMAIN_BUS_VMD_MSI
x86/irq: Initialize PCI/MSI domain at PCI init time
x86/pci: Reducde #ifdeffery in PCI init code
...
Fix sparse build warning:
drivers/pci/controller/pcie-iproc-platform.c:102:33: warning: Using plain integer as NULL pointer
The map_irq member of the struct iproc_pcie takes a function pointer
serving as a callback to map interrupts, therefore we should pass a NULL
pointer to it rather than a integer in the iproc_pcie_pltfm_probe()
function.
Related:
commit b64aa11eb2 ("PCI: Set bridge map_irq and swizzle_irq to
default functions")
Link: https://lore.kernel.org/r/20200922194932.465925-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Enable pci-meson to build as a module whenever ARCH_MESON is enabled.
Link: https://lore.kernel.org/r/20200918181251.32423-1-khilman@baylibre.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Yue Wang <yue.wang@amlogic.com>
Old ATF automatically power on pcie phy and does not provide SMC call for
phy power on functionality which leads to aardvark initialization failure:
[ 0.330134] mvebu-a3700-comphy d0018300.phy: unsupported SMC call, try updating your firmware
[ 0.338846] phy phy-d0018300.phy.1: phy poweron failed --> -95
[ 0.344753] advk-pcie d0070000.pcie: Failed to initialize PHY (-95)
[ 0.351160] advk-pcie: probe of d0070000.pcie failed with error -95
This patch fixes above failure by ignoring 'not supported' error in
aardvark driver. In this case it is expected that phy is already power on.
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://lore.kernel.org/r/20200902144344.16684-3-pali@kernel.org
Fixes: 366697018c ("PCI: aardvark: Add PHY support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: <stable@vger.kernel.org> # 5.8+: ea17a0f153af: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
The value assigned to msi_val after the inner loop finishes its run is
never used for anything, and it is also immediately overridden in the
line that follows with the return value from the xgene_msi_int_read()
function.
Since the value of msi_val following the inner loop completion is never
used in any meaningful way the assignment can be removed.
Addresses-Coverity-ID: 1437183 ("Unused value")
Link: https://lore.kernel.org/r/20200922030257.459898-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Simplify the return expression by removing useless code.
Link: https://lore.kernel.org/r/20200921082447.2591877-1-liushixin2@huawei.com
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
module_bcma_driver() makes the code simpler by eliminating
boilerplate code.
Link: https://lore.kernel.org/r/20200918030829.3946025-1-liushixin2@huawei.com
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Now that the support is in place with previous commits, we add several
chips that use the BrcmSTB driver.
Link: https://lore.kernel.org/r/20200911175232.19016-11-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
The proper value of the parameter SCB_MAX_BURST_SIZE varies per chip. The
2711 family requires 128B whereas other devices can employ 512. The
assignment is complicated by the fact that the values for this two-bit
field have different meanings;
Value Type_Generic Type_7278
00 Reserved 128B
01 128B 256B
10 256B 512B
11 512B Reserved
Link: https://lore.kernel.org/r/20200911175232.19016-10-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Older BrcmSTB chips do not have a separate register for MSI interrupts; the
MSIs are in a register that also contains unrelated interrupts. In
addition, the interrupts lie in bits [31..24] for these legacy chips. This
commit provides common code for both legacy and non-legacy MSI interrupt
registers.
Link: https://lore.kernel.org/r/20200911175232.19016-9-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
The Raspberry Pi (RPI) is currently the only chip using this driver
(pcie-brcmstb.c). There, only one memory controller is used, without an
extension region, and the SCB0 viewport size is set to the size of the
first and only dma-range region. Other BrcmSTB SOCs have more complicated
memory configurations that require setting additional viewport sizes.
BrcmSTB PCIe controllers are intimately connected to the memory
controller(s) on the SOC. The SOC may have one to three memory
controllers; they are indicated by the term SCBi. Each controller has a
base region and an optional extension region. In physical memory, the base
and extension regions of a controller are not adjacent, but in PCIe-space
they are.
There is a "viewport" for each memory controller that allows DMA from
endpoint devices. Each viewport's size must be set to a power of two, and
that size must be equal to or larger than the amount of memory each
controller supports which is the sum of base region and its optional
extension. Further, the 1-3 viewports are also adjacent in PCIe-space.
Unfortunately the viewport sizes cannot be ascertained from the
"dma-ranges" property so they have their own property, "brcm,scb-sizes".
This is because dma-range information does not indicate what memory
controller it is associated. For example, consider the following case
where the size of one dma-range is 2GB and the second dma-range is 1GB:
/* Case 1: SCB0 size set to 4GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)
/* Case 2: SCB0 size set to 2GB, SCB1 size set to 1GB */
dma-range0: 2GB (from memc0-base)
dma-range1: 1GB (from memc0-extension)
By just looking at the dma-ranges information, one cannot tell which
situation applies. That is why an additional property is needed. Its
length indicates the number of memory controllers being used and each value
indicates the viewport size.
Note that the RPI DT does not have a "brcm,scb-sizes" property value,
as it is assumed that it only requires one memory controller and no
extension. So the optional use of "brcm,scb-sizes" will be backwards
compatible.
One last layer of complexity exists: all of the viewports sizes must be
added and rounded up to a power of two to determine what the "BAR" size is.
Further, an offset must be given that indicates the base PCIe address of
this "BAR". The use of the term BAR is typically associated with endpoint
devices, and the term is used here because the PCIe HW may be used as an RC
or an EP. In the former case, all of the system memory appears in a single
"BAR" region in PCIe memory. As it turns out, BrcmSTB PCIe HW is rarely
used in the EP role and its system of mapping memory is an artifact that
requires multiple dma-ranges regions.
Link: https://lore.kernel.org/r/20200911175232.19016-8-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Some STB chips have a special purpose reset controller named RESCAL (reset
calibration). The PCIe HW can now control RESCAL to start and stop its
operation. On probe(), the RESCAL is deasserted and the driver goes
through the sequence of setting registers and reading status in order to
start the internal PHY that is required for the PCIe.
Link: https://lore.kernel.org/r/20200911175232.19016-7-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
pci_restore_msi_state() directly writes the MSI/MSI-X related registers
via MMIO. On a physical machine, this works perfectly; for a Linux VM
running on a hypervisor, which typically enables IOMMU interrupt remapping,
the hypervisor usually should trap and emulate the MMIO accesses in order
to re-create the necessary interrupt remapping table entries in the IOMMU,
otherwise the interrupts can not work in the VM after hibernation.
Hyper-V is different from other hypervisors in that it does not trap and
emulate the MMIO accesses, and instead it uses a para-virtualized method,
which requires the VM to call hv_compose_msi_msg() to notify the hypervisor
of the info that would be passed to the hypervisor in the case of the
trap-and-emulate method. This is not an issue to a lot of PCI device
drivers, which destroy and re-create the interrupts across hibernation, so
hv_compose_msi_msg() is called automatically. However, some PCI device
drivers (e.g. the in-tree GPU driver nouveau and the out-of-tree Nvidia
proprietary GPU driver) do not destroy and re-create MSI/MSI-X interrupts
across hibernation, so hv_pci_resume() has to call hv_compose_msi_msg(),
otherwise the PCI device drivers can no longer receive interrupts after
the VM resumes from hibernation.
Hyper-V is also different in that chip->irq_unmask() may fail in a
Linux VM running on Hyper-V (on a physical machine, chip->irq_unmask()
can not fail because unmasking an MSI/MSI-X register just means an MMIO
write): during hibernation, when a CPU is offlined, the kernel tries
to move the interrupt to the remaining CPUs that haven't been offlined
yet. In this case, hv_irq_unmask() -> hv_do_hypercall() always fails
because the vmbus channel has been closed: here the early "return" in
hv_irq_unmask() means the pci_msi_unmask_irq() is not called, i.e. the
desc->masked remains "true", so later after hibernation, the MSI interrupt
always remains masked, which is incorrect. Refer to cpu_disable_common()
-> fixup_irqs() -> irq_migrate_all_off_this_cpu() -> migrate_one_irq():
static bool migrate_one_irq(struct irq_desc *desc)
{
...
if (maskchip && chip->irq_mask)
chip->irq_mask(d);
...
err = irq_do_set_affinity(d, affinity, false);
...
if (maskchip && chip->irq_unmask)
chip->irq_unmask(d);
Fix the issue by calling pci_msi_unmask_irq() unconditionally in
hv_irq_unmask(). Also suppress the error message for hibernation because
the hypercall failure during hibernation does not matter (at this time
all the devices have been frozen). Note: the correct affinity info is
still updated into the irqdata data structure in migrate_one_irq() ->
irq_do_set_affinity() -> hv_set_affinity(), so later when the VM
resumes, hv_pci_restore_msi_state() is able to correctly restore
the interrupt with the correct affinity.
Link: https://lore.kernel.org/r/20201002085158.9168-1-decui@microsoft.com
Fixes: ac82fc8327 ("PCI: hv: Add hibernation support")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
PCI host bridge driver can be probed before the gpiochip it requires,
so, of_get_named_gpio() can return -EPROBE_DEFER. Current code lets the
kirin_pcie_probe() directly return -ENODEV, which results in the PCI
host controller driver probe failure; with this error code the PCI host
controller driver will not be probed again when the gpiochip driver is
loaded.
Fix the above issue by letting kirin_pcie_probe() return -EPROBE_DEFER in
such a case.
Link: https://lore.kernel.org/r/20200918123800.19983-1-huobean@gmail.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use DEFINE_SEQ_ATTRIBUTE macro to simplify the code.
Link: https://lore.kernel.org/r/20200916025025.3992783-1-liushixin2@huawei.com
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add missing documentation for the parameter "version" and "num_version"
of the hv_pci_protocol_negotiation() function and resolve build time
kernel-doc warnings:
drivers/pci/controller/pci-hyperv.c:2535: warning: Function parameter
or member 'version' not described in 'hv_pci_protocol_negotiation'
drivers/pci/controller/pci-hyperv.c:2535: warning: Function parameter
or member 'num_version' not described in 'hv_pci_protocol_negotiation'
No change to functionality intended.
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20200925234753.1767227-1-kw@linux.com
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Add PCIe EP mode support for ls1088a and ls2088a, there are some
difference between LS1 and LS2 platform, so refactor the code of
the EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-10-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
dw_pcie_ep_raise_msix_irq was never called in the exisitng driver
before, because the ls1046a platform don't support the MSIX feature
and msix_capable was always set to false.
Now that add the ls1088a platform with MSIX support, use the doorbell
method to support the MSIX feature.
Link: https://lore.kernel.org/r/20200918080024.13639-9-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The different PCIe controller in one board may be have different
capability of MSI or MSIX, so change the way of getting the MSI
capability, make it more flexible.
Link: https://lore.kernel.org/r/20200918080024.13639-8-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Fix some format issue of the code in EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-7-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Each PF of EP device should have its own MSI or MSIX capabitily
struct, so create a dw_pcie_ep_func struct and move the msi_cap
and msix_cap to this struct from dw_pcie_ep, and manage the PFs
via a list.
Link: https://lore.kernel.org/r/20200918080024.13639-5-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Move the function of getting MSI capability to the front of init
function, because the init function of the EP platform driver will use
the return value by the function of getting MSI capability.
Link: https://lore.kernel.org/r/20200918080024.13639-4-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add the doorbell mode of MSI-X in DWC EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-3-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add multiple PFs support for DWC, due to different PF have different
config space, we use func_conf_select callback function to access
the different PF's config space, the different chip company need to
implement this callback function when use the DWC IP core and intend
to support multiple PFs feature.
Link: https://lore.kernel.org/r/20200918080024.13639-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The PERST# bit was moved to a different register in 7278-type STB chips.
In addition, the polarity of the bit was also changed; for other chips
writing a 1 specified assert; for 7278-type chips, writing a 0 specifies
assert. Of course, PERST# is a PCIe asserted-low signal.
While we are here, also change the bridge_sw_init_set() functions so like
the perst_set() functions they are chip specific and we no longer rely on
data wrt chip specific field mask and shift values.
Link: https://lore.kernel.org/r/20200911175232.19016-6-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend
and resume. Now the PCIe driver may do so as well.
Link: https://lore.kernel.org/r/20200911175232.19016-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Add in compatibility strings and code for three Broadcom STB chips. Some
of the register locations, shifts, and masks are different for certain
chips, requiring the use of different constants based on of_id.
We would like to add the following at this time to the match list but we
need to wait until the end of this patchset so that everything works.
{ .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
{ .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
Link: https://lore.kernel.org/r/20200911175232.19016-4-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Have PCIE_BRCMSTB depend on ARCH_BRCMSTB. Also set the default value to
ARCH_BRCMSTB.
Link: https://lore.kernel.org/r/20200911175232.19016-2-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
The arch_.*_msi_irq[s] fallbacks are compiled in whether an architecture
requires them or not. Architectures which are fully utilizing hierarchical
irq domains should never call into that code.
It's not only architectures which depend on that by implementing one or
more of the weak functions, there is also a bunch of drivers which relies
on the weak functions which invoke msi_controller::setup_irq[s] and
msi_controller::teardown_irq.
Make the architectures and drivers which rely on them select them in Kconfig
and if not selected replace them by stub functions which emit a warning and
fail the PCI/MSI interrupt allocation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200826112333.992429909@linutronix.de
Devices on the VMD bus use their own MSI irq domain, but it is not
distinguishable from regular PCI/MSI irq domains. This is required
to exclude VMD devices from getting the irq domain pointer set by
interrupt remapping.
Override the default bus token.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112333.047315047@linutronix.de
pci_msi_get_hwirq() and pci_msi_set_desc are not longer special. Enable the
generic MSI domain ops in the core and PCI MSI code unconditionally and get
rid of the x86 specific implementations in the X86 MSI code and in the
hyperv PCI driver.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200826112332.564274859@linutronix.de
Convert the interrupt remap drivers to retrieve the pci device from the msi
descriptor and use info::hwirq.
This is the first step to prepare x86 for using the generic MSI domain ops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112332.466405395@linutronix.de
VMD has it's own PCI/MSI interrupt domain which is not in any way depending
on the x86 vector domain. PCI devices behind VMD share the VMD MSIX vector
entries via a VMD specific message translation to the actual VMD MSIX
vector. The VMD device interrupt handler for the VMD MSIX vectors invokes
all interrupt handlers of the devices which share a vector.
Making the x86 vector domain the actual parent of the VMD irq domain is
pointless and actually counterproductive. When a device interrupt is
requested then it will activate the interrupt which traverses down the
hierarchy and consumes an interrupt vector in the vector domain which is
never used.
The domain is self contained and has no parent dependencies, so just hand
in NULL for the parent and be done with it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200826112330.928952181@linutronix.de
The HiSilicon HIP PCIe controller is capable of handling errors
on root port and performing port reset separately at each root port.
Add error handling driver for HIP PCIe controller to log
and report recoverable errors. Perform root port reset and restore
link status after the recovery.
Following are some of the PCIe controller's recoverable errors
1. completion transmission timeout error.
2. CRS retry counter over the threshold error.
3. ECC 2 bit errors
4. AXI bresponse/rresponse errors etc.
The driver placed in the drivers/pci/controller/ because the
HIP PCIe controller does not use DWC IP.
Link: https://lore.kernel.org/r/20200903123456.1823-3-shiju.jose@huawei.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Convert the remaining cases of register accesses using dbi_base rather
than dw_pcie_(read|write)[bwl]_dbi accessors.
Link: https://lore.kernel.org/r/20200821035420.380495-41-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The Designware controller has common registers to set number of fast
training sequence ordered sets. The Artpec6, Intel, and Tegra driver
initialize these register fields. Let's move the initialization to the
common setup code and drivers just have to provide the value.
There's a slight change in that the common clock mode N_FTS field is
now initialized. Previously only the Intel driver set this. It's not
clear from the code if common clock mode is used in the Artpec6 or Tegra
driver. It depends on the DWC configuration. Given the field is not
initialized while the others are, it seems unlikely common clock mode
is used.
Link: https://lore.kernel.org/r/20200821035420.380495-40-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
'max_width' is read, but never used, so let's remove it.
Link: https://lore.kernel.org/r/20200821035420.380495-39-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The PCI_CAP_ID_EXP offset is only needed by intel_pcie_link_setup(), so
let's retrieve it there and avoid storing the offset.
Link: https://lore.kernel.org/r/20200821035420.380495-38-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
A driver doesn't need to check for DT 'device_type' property, so let's
remove the check.
Link: https://lore.kernel.org/r/20200821035420.380495-37-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Intel driver is the only one to set PORT_LINK_DLL_LINK_EN. The
default value is set and it seems pretty certain that enabling link
initialization is always required. Maybe it could just be dropped from
the Intel driver, but lets move setting it into the common code to be
sure.
Link: https://lore.kernel.org/r/20200821035420.380495-36-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The root bus checks rework in d84c572de1 ("PCI: rockchip: Use
pci_is_root_bus() to check if bus is root bus") caused a regression whereby
in rockchip_pcie_valid_device() if the bus parameter is the root bus and
the dev value == 0, the function should return 1 (ie true) without checking
if the bus->parent pointer is a root bus because that triggers a NULL
pointer dereference.
Fix this by streamlining the root bus detection.
Fixes: d84c572de1 ("PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus")
Link: https://lore.kernel.org/r/20200904140904.944-1-lorenzo.pieralisi@arm.com
Reported-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Tested-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
The core interrupt code expects the irq_set_affinity call to update the
effective affinity for the interrupt. This was not being done, so update
iproc_msi_irq_set_affinity() to do so.
Link: https://lore.kernel.org/r/20200803035241.7737-1-mark.tomlinson@alliedtelesis.co.nz
Fixes: 3bc2b23488 ("PCI: iproc: Add iProc PCIe MSI support")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
The mvebu host controller driver allocates an msi_controller structure
pointer without allocating the structure and initializing its methods,
which makes the pointer useless.
This means that the PCI IRQ MSI layer ignores it and that after all it
should not really be needed.
Remove it.
Link: https://lore.kernel.org/r/20200904142132.6054-1-lorenzo.pieralisi@arm.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The ATU registers are only accessed in pcie-designware.c and can be private
to it.
Link: https://lore.kernel.org/r/20200821035420.380495-34-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The DBI2 appears to be write-only and there's no read accesses in the code
anyways, so let's remove all the read_dbi2 related code.
Link: https://lore.kernel.org/r/20200821035420.380495-33-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The Tegra driver has its own defines for common Designware Port Logic
registers. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-32-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
While the Designware controller appears to hard code the PCI_CAP_ID_EXP
capability register at 0x70, there's no need to hard code this in the
driver as it is discoverable.
Link: https://lore.kernel.org/r/20200821035420.380495-31-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: linux-omap@vger.kernel.org
The QCom driver has its own defines for common PCI config space
registers. It also hard codes the capability register offsets which are
discoverable. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-30-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-arm-msm@vger.kernel.org
The i.MX6 driver has its own defines for common PCI config space
registers. It also hard codes the capability register offsets which are
discoverable. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-29-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
The meson 'elbi' registers are just the Designware 'dbi' space and all
the registers accessed are either standard PCI config space or DWC port
logic registers. Convert the accesses to use the common defines and
register accessors.
Link: https://lore.kernel.org/r/20200821035420.380495-28-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: linux-amlogic@lists.infradead.org
The common Designware init already initializes the RC PCI_COMMAND, BAR0
and BAR1 registers.
The only difference here is the common code sets SERR. If clearing SERR
is what's desired, then the Meson driver should do that instead.
Link: https://lore.kernel.org/r/20200821035420.380495-27-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
The meson lanes initialization is the same DWC port logic registers as
in dw_pcie_setup(). We just need to initialize 'num_lanes' to 1 to do
the same init.
dw_pcie_setup_rc() sets the PORT_LOGIC_SPEED_CHANGE bit, so setting it
can be dropped.
Link: https://lore.kernel.org/r/20200821035420.380495-26-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-amlogic@lists.infradead.org
"Fast Link Mode" is a simulation environment speed up setting which should
never be set and the default is not set. However some Amlogic platforms
have it set (by firmware presumably). See commit 87dccf0932 ("PCI:
amlogic: meson: Don't use FAST_LINK_MODE to set up link") for more
information. Let's clear it in core DWC code so we can drop some vendor
specific code.
Link: https://lore.kernel.org/r/20200821035420.380495-25-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Add a 'num_lanes' field to allow drivers to provide a the number of lanes
if not in DT or using a custom DT property. A driver can provide a
non-zero value which is used if the DT doesn't have a 'num-lanes'
property.
Link: https://lore.kernel.org/r/20200821035420.380495-24-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
PCIE_LINK_WIDTH_SPEED_CONTROL is already defined in pcie-designware.h,
so remove it from the i.MX6 driver.
Link: https://lore.kernel.org/r/20200821035420.380495-23-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
The DWC core driver already parses and stores the 'num-viewport' DT
property, so there is no need for the Keystone driver to store it.
Link: https://lore.kernel.org/r/20200821035420.380495-21-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The config space is divided in half for type 0 and type 1 accesses, but
this is pointless as there's only one iATU window which is
reconfigured on each access.
The only platform doing something custom is TI Keystone (surprise!).
It does its own mapping of the config space to avoid spliting the
config space and never actually uses va_cfg1_base as it has its own
config space accessors. With the splitting removed, Keystone can use the
default mapping of config space.
Link: https://lore.kernel.org/r/20200821035420.380495-20-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The PCI bridge resources are stored in pci_host_bridge.windows, so
there's no need to store them in a DWC specific struct. There's also no
need to parse the resources and store them a 2nd time as they are mainly
used for one time setup of iATU windows.
Link: https://lore.kernel.org/r/20200821035420.380495-19-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The pci_host_bridge struct already has a pointer to its pci_bus, so
let's convert the one user to use the bridge struct and remove the
private 'root_bus' pointer.
Link: https://lore.kernel.org/r/20200821035420.380495-18-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that there are no more .scan_bus() callbacks, we can remove it and just
use pci_host_probe().
Link: https://lore.kernel.org/r/20200821035420.380495-17-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
TI keystone is the only Designware driver using .scan_bus(). This
function pointer is the only thing preventing the Designware driver from
using pci_host_probe(). Let's use the pci_ops.add_bus hook instead.
Link: https://lore.kernel.org/r/20200821035420.380495-16-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that all the platforms with custom config access handling define
their own pci_ops, let's split the default config accessors to use
different pci_ops for root and child buses. With this, we can use the
generic config accessors. The child bus accesses mainly require a
.map_bus() hook to reconfigure the iATU on each config space access.
Link: https://lore.kernel.org/r/20200821035420.380495-14-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that all the drivers needing custom config accessors have been
converted to define their own pci_ops, we can remove the DWC specific
function callbacks {rd,wr}_{own,other}_conf.
Link: https://lore.kernel.org/r/20200821035420.380495-13-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the HiSilicon histb driver to use the standard pci_ops
for root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-12-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Samsung Exynos driver to use the standard pci_ops for
root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-11-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the HiSilicon Kirin driver to use the standard pci_ops
for root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-10-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Amlogic meson driver to use the standard pci_ops for
root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-9-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Tegra driver to use the standard pci_ops for root
bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-8-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the TI Keystone driver to use the standard pci_ops for
config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-7-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Amazon driver to use the standard pci_ops for child
bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-6-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Designware root port config space is memory mapped accesses via the
DBI space by default. Add a common implementation
dw_pcie_own_conf_map_bus() for platforms to use.
Link: https://lore.kernel.org/r/20200821035420.380495-5-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
This comment still refers to the old driver pathname,
when all PCI drivers were located directly under the
drivers/pci directory.
Anyway the function name itself is enough, so we can
remove the overabundant path reference.
Link: https://lore.kernel.org/r/20200623074851.7832-1-f.suligoi@asem.it
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When devm_clk_get() returns -EPROBE_DEFER, i.MX6 PCI driver should
NOT print error message, use dev_err_probe() to handle it.
Link: https://lore.kernel.org/r/1597109364-4739-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move code which belongs to link training (delays and resets) into
advk_pcie_train_link() function, so everything related to link training,
including timings is at one place.
After experiments it can be observed that link training in aardvark
hardware is very sensitive to timings and delays, so it is a good idea to
have this code at the same place as link training calls.
This patch does not change behavior of aardvark initialization.
Link: https://lore.kernel.org/r/20200907111038.5811-6-pali@kernel.org
Tested-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Providing driver's 'remove' function allows kernel to bind and unbind devices
from aardvark driver. It also allows to build aardvark driver as a module.
Compiling aardvark as a module simplifies development and debugging of
this driver as it can be reloaded at runtime without the need to reboot
to new kernel.
Link: https://lore.kernel.org/r/20200907111038.5811-5-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Include linux/gpio/consumer.h instead of linux/gpio.h, as is said in the
latter file.
This was reported by kernel test bot when compiling for s390.
drivers/pci/controller/pci-aardvark.c:350:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-aardvark.c:1074:21: error: implicit declaration of function 'devm_gpiod_get_from_of_node' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-aardvark.c:1076:14: error: use of undeclared identifier 'GPIOD_OUT_LOW'
Link: https://lore.kernel.org/r/202006211118.LxtENQfl%25lkp@intel.com
Link: https://lore.kernel.org/r/20200907111038.5811-2-pali@kernel.org
Fixes: 5169a9851d ("PCI: aardvark: Issue PERST via GPIO")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Qsdk U-Boot can incorrectly leave the PCIe interface in an undefined
state if bootm command is used instead of bootipq. This is caused by the
not deinit of PCIe when bootm is called. Reset the PCIe before init
anyway to fix this U-Boot bug.
Link: https://lore.kernel.org/r/20200901124955.137-1-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable@vger.kernel.org # v4.19+
Some fields in the host bridge structure are now initialized
by default in the PCI/OF core functions therefore their
initialization in the host controller driver is superfluous.
Remove it.
Link: https://lore.kernel.org/r/20200904142710.8018-1-lorenzo.pieralisi@arm.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Link: https://lore.kernel.org/r/20200818133739.463193-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pci@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
In preparation to allow drivers to set their own root and child pci_ops
instead of using the DWC specific config space ops, we need to make
the pci_host_bridge pointer available and move setting the bridge->ops
and bridge->child_ops pointer to before the .host_init() hook.
Link: https://lore.kernel.org/r/20200821035420.380495-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Designware DBI space contains the root bus bridge config space.
Platforms needing custom {rd,wr}_own_conf functions are also the ones
needing custom {read,write}_dbi ops functions and the access sequences
are the same.
Replace all dw_pcie_{rd,wr}_own_conf() calls with the DBI variants in
preparation to remove dw_pcie_{rd,wr}_own_conf().
Link: https://lore.kernel.org/r/20200821035420.380495-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The current check will result in the multiple function device
fails to initialize. So fix the check by masking out the
multiple function bit.
Link: https://lore.kernel.org/r/20200818092746.24366-1-Zhiqiang.Hou@nxp.com
Fixes: 0b24134f78 ("PCI: dwc: Add validation that PCIe core is set to correct mode")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge 5.9-rc3 into usb-next
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 44331189f9.
Now that the VL805 init routine is run through a reset controller driver
the device dependencies are being taken care of by the device core. No
need to do it manually here.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-10-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Remove redundant logging for platform_get_irq() errors (Krzysztof
Wilczyński)
* pci/irq-error:
PCI: Remove dev_err() when handing an error from platform_get_irq()
- Use pci_host_bridge.windows list directly instead of splicing in a
temporary list for cadence, mvebu, host-common (Rob Herring)
- Use pci_host_probe() instead of open-coding all the pieces for altera,
brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3, versatile, xgene,
xilinx, xilinx-nwl (Rob Herring)
- Convert to devm_platform_ioremap_resource_byname() instead of open-coding
platform_get_resource_byname() and devm_ioremap_resource() for altera,
cadence, mediatek, rockchip, tegra, xgene (Dejin Zheng)
- Convert to devm_platform_ioremap_resource() instead of open-coding
platform_get_resource() and devm_ioremap_resource() for aardvark,
brcmstb, exynos, ftpci100, versatile (Dejin Zheng)
- Remove redundant error messages from devm_pci_remap_cfg_resource()
callers (Dejin Zheng)
- Drop useless PCI_ENABLE_PROC_DOMAINS from versatile driver (Rob Herring)
- Default host bridge parent device to the platform device (Rob Herring)
- Drop unnecessary zeroing of host bridge fields (Rob Herring)
- Use pci_is_root_bus() instead of tracking root bus number separately in
aardvark, designware (imx6, keystone, designware-host), mobiveil,
xilinx-nwl, xilinx, rockchip, rcar (Rob Herring)
- Set host bridge bus number in pci_scan_root_bus_bridge() instead of each
driver for aardvark, designware-host, host-common, mediatek, rcar, tegra,
v3-semi (Rob Herring)
- Use bridge resources instead of parsing DT 'ranges' again for cadence
(Rob Herring)
- Remove private bus number and range from cadence (Rob Herring)
- Use devm_pci_alloc_host_bridge() to simplify rcar (Rob Herring)
- Use struct pci_host_bridge.windows list directly rather than a temporary
(Rob Herring)
- Reduce OF "missing non-prefetchable window" from error to warning message
(Rob Herring)
- Convert rcar-gen2 from old Arm-specific pci_common_init_dev() to new
arch-independent interfaces (Rob Herring)
- Move DT resource setup into devm_pci_alloc_host_bridge() (Rob Herring)
- Set bridge map_irq and swizzle_irq to default functions; drivers that
don't support legacy IRQs (iproc) need to undo this (Rob Herring)
* pci/host-probe-refactor:
PCI: Set bridge map_irq and swizzle_irq to default functions
PCI: Move DT resource setup into devm_pci_alloc_host_bridge()
PCI: rcar-gen2: Convert to use modern host bridge probe functions
PCI: of: Reduce missing non-prefetchable memory region to a warning
PCI: rcar: Use struct pci_host_bridge.windows list directly
PCI: rcar: Use devm_pci_alloc_host_bridge()
PCI: cadence: Remove private bus number and range storage
PCI: cadence: Use bridge resources for outbound window setup
PCI: Move setting pci_host_bridge.busnr out of host drivers
PCI: rcar: Use pci_is_root_bus() to check if bus is root bus
PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx-nwl: Use pci_is_root_bus() to check if bus is root bus
PCI: mobiveil: Use pci_is_root_bus() to check if bus is root bus
PCI: designware: Use pci_is_root_bus() to check if bus is root bus
PCI: aardvark: Use pci_is_root_bus() to check if bus is root bus
PCI: Drop unnecessary zeroing of bridge fields
PCI: Set default bridge parent device
PCI: versatile: Drop flag PCI_ENABLE_PROC_DOMAINS
PCI: controller: Remove duplicate error message
PCI: controller: Convert to devm_platform_ioremap_resource()
PCI: controller: Convert to devm_platform_ioremap_resource_byname()
PCI: xilinx: Use pci_host_probe() to register host
PCI: xilinx-nwl: Use pci_host_probe() to register host
PCI: rockchip: Use pci_host_probe() to register host
PCI: rcar: Use pci_host_probe() to register host
PCI: iproc: Use pci_host_probe() to register host
PCI: altera: Use pci_host_probe() to register host
PCI: xgene: Use pci_host_probe() to register host
PCI: versatile: Use pci_host_probe() to register host
PCI: v3: Use pci_host_probe() to register host
PCI: tegra: Use pci_host_probe() to register host
PCI: mobiveil: Use pci_host_probe() to register host
PCI: brcmstb: Use pci_host_probe() to register host
PCI: host-common: Use struct pci_host_bridge.windows list directly
PCI: mvebu: Use struct pci_host_bridge.windows list directly
PCI: cadence: Use struct pci_host_bridge.windows list directly
# Conflicts:
# drivers/pci/controller/cadence/pcie-cadence-host.c
- Set up mvebu BAR 0 so MSI works even if bootloader doesn't do this
(Shmuel Hazan)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Setup BAR0 in order to fix MSI
- Fix loongson class code quirk so it happens early enough (Tiezhu Yang)
* remotes/lorenzo/pci/loongson:
PCI: loongson: Use DECLARE_PCI_FIXUP_EARLY for bridge_class_quirk()
- Fix hv timing issue that causes kdump failures (Wei Hu)
- Make some hv functions static (Wei Yongjun)
* remotes/lorenzo/pci/hv:
PCI: hv: Make some functions static
PCI: hv: Fix a timing issue which causes kdump to fail occasionally
- Convert cadence to use standard "dma-ranges" DT property instead of its
own "cdns,no-bar-match-nbits" (Kishon Vijay Abraham I)
- Fix pm_runtime_put_sync() issues in cadence error paths (Kishon Vijay
Abraham I)
- Add PTR_ALIGN_DOWN macro (Kishon Vijay Abraham I)
- Convert cadence r/w accessors to only 32-bit accesses (Kishon Vijay
Abraham I)
- Add cadence support to start Link and check Link status (Kishon Vijay
Abraham I)
- Allow custom PCI ops for cadence-based drivers (Kishon Vijay Abraham I)
- Remove "mem" from cadence reg binding since it's not memory and it
overlaps the PCIe config and memory region (Kishon Vijay Abraham I)
- Add cadence ->cpu_addr_fixup() for platforms that require absolute
addresses in the ATU, not just offsets (Kishon Vijay Abraham I)
- Update cadence Vendor IDs using local management registers, not
architected config space (Kishon Vijay Abraham I)
- Add cadence endpoint driver MSI-X support (Kishon Vijay Abraham I)
- Add bindings and driver for TI J721E SoC, supporting both host and
endpoint mode (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
MAINTAINERS: Add Kishon Vijay Abraham I for TI J721E SoC PCIe
misc: pci_endpoint_test: Add J721E in pci_device_id table
PCI: j721e: Add TI J721E PCIe driver
dt-bindings: PCI: Add EP mode dt-bindings for TI's J721E SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J721E SoC
PCI: cadence: Add MSI-X support to Endpoint driver
PCI: cadence: Fix updating Vendor ID and Subsystem Vendor ID register
PCI: cadence: Add new *ops* for CPU addr fixup
dt-bindings: PCI: cadence: Remove "mem" from reg binding
PCI: cadence: Allow pci_host_bridge to have custom pci_ops
PCI: cadence: Add support to start link and verify link status
PCI: cadence: Convert all r/w accessors to perform only 32-bit accesses
linux/kernel.h: Add PTR_ALIGN_DOWN macro
PCI: cadence: Fix cdns_pcie_{host|ep}_setup() error path
PCI: cadence: Use "dma-ranges" instead of "cdns,no-bar-match-nbits" property
Add support for Versal CPM as Root Port.
The Versal ACAP devices include CCIX-PCIe Module (CPM). The integrated
block for CPM along with the integrated bridge can function as PCIe Root
Port.
Bridge error and legacy interrupts in Versal CPM are handled using Versal
CPM specific interrupt line.
[bhelgaas: fold in kerneldoc fix from
https://lore.kernel.org/linux-acpi/20200729201224.26799-7-krzk@kernel.org/]
Link: https://lore.kernel.org/r/1592312214-9347-3-git-send-email-bharat.kumar.gogada@xilinx.com
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The majority of DT based host drivers use the default .map_irq() and
.swizzle_irq() functions, so let's initialize the function pointers to
the default and drop setting them in the host drivers.
Drivers like iProc which don't support legacy interrupts need to set
.map_irq() back to NULL.
Link: https://lore.kernel.org/r/20200722022514.1283916-20-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that pci_parse_request_of_pci_ranges() callers just setup
pci_host_bridge.windows and dma_ranges directly and don't need the bus
range returned, we can just initialize them when allocating the
pci_host_bridge struct.
With this, pci_parse_request_of_pci_ranges() becomes a static function.
Link: https://lore.kernel.org/r/20200722022514.1283916-19-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The rcar-gen2 host driver still uses the old Arm PCI setup function
pci_common_init_dev(). Let's update it to use the modern
devm_pci_alloc_host_bridge(), pci_parse_request_of_pci_ranges() and
pci_host_probe() functions.
Link: https://lore.kernel.org/r/20200722022514.1283916-18-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-renesas-soc@vger.kernel.org
Add support for PCIe controller in J721E SoC. The controller uses the
Cadence PCIe core programmed by pcie-cadence*.c. The PCIe controller
will work in both host mode and device mode.
Some of the features of the controller are:
*) Supports both RC mode and EP mode
*) Supports MSI and MSI-X support
*) Supports upto GEN3 speed mode
*) Supports SR-IOV capability
*) Ability to route all transactions via SMMU (support will be added
in a later patch).
Link: https://lore.kernel.org/r/20200722110317.4744-14-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Implement ->set_msix() and ->get_msix() callback functions in order
to configure MSIX capability in the PCIe endpoint controller.
Add cdns_pcie_ep_send_msix_irq() to send MSIX interrupts to Host.
cdns_pcie_ep_send_msix_irq() gets the MSIX table address (virtual
address) from "struct cdns_pcie_epf" that gets initialized in
->set_bar() call back function.
[kishon@ti.com: Re-implement MSIX support in accordance with the
re-designed core MSI-X interfaces]
Link: https://lore.kernel.org/r/20200722110317.4744-11-kishon@ti.com
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
sparse report build warning as follows:
drivers/pci/controller/pci-hyperv.c:941:5: warning:
symbol 'hv_read_config_block' was not declared. Should it be static?
drivers/pci/controller/pci-hyperv.c:1021:5: warning:
symbol 'hv_write_config_block' was not declared. Should it be static?
drivers/pci/controller/pci-hyperv.c:1090:5: warning:
symbol 'hv_register_block_invalidate' was not declared. Should it be static?
Those functions are not used outside of this file, so mark them static.
Link: https://lore.kernel.org/r/20200706135234.80758-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The Tegra PCI controller driver doesn't need to control the PLL power
supplies directly, but rather uses the pads provided by the XUSB pad
controller, which in turn is responsible for supplying power to the
PLLs.
Link: https://lore.kernel.org/r/20200623145528.1658337-2-thierry.reding@gmail.com
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The HiSilicon non-ECAM PCIe has been broken since March 2016 commit
7e57fd1444 ("PCI: designware: Move Root Complex setup code to
dw_pcie_setup_rc()"). The reason is this commit moved the iATU setup code
from dw_pcie_host_init() to dw_pcie_setup_rc(), but the hisi driver never
calls dw_pcie_setup_rc(). The result is the PCI memory space is never
configured and the driver can't work. It's also clear it has an iATU as
the config space accesses use it.
There's also no dts file using either "hisilicon,hip05-pcie" or
"hisilicon,hip06-pcie".
Link: https://lore.kernel.org/r/20200724224204.3249055-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Commit 1b79c52844 ("PCI: cadence: Add host driver for Cadence PCIe
controller") in order to update Vendor ID, directly wrote to
PCI_VENDOR_ID register. However PCI_VENDOR_ID in root port configuration
space is read-only register and writing to it will have no effect.
Use local management register to configure Vendor ID and Subsystem Vendor
ID.
Link: https://lore.kernel.org/r/20200722110317.4744-10-kishon@ti.com
Fixes: 1b79c52844 ("PCI: cadence: Add host driver for Cadence PCIe controller")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cadence driver uses "mem" memory resource to obtain the offset of
configuration space address region, memory space address region and
message space address region. The obtained offset is used to program
the Address Translation Unit (ATU). However certain platforms like TI's
J721E SoC require the absolute address to be programmed in the ATU and
not just the offset. Add new *ops* for CPU addr fixup for the platform
drivers to provide the correct address to be programmed in the ATU.
Link: https://lore.kernel.org/r/20200722110317.4744-9-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Certain platforms like TI's J721E allows only 32-bit configuration
space access. In such cases pci_generic_config_read and
pci_generic_config_write cannot be used. Add support in Cadence core
to let pci_host_bridge have custom pci_ops.
Link: https://lore.kernel.org/r/20200722110317.4744-7-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add cdns_pcie_ops to start link and verify link status. The registers
to start link and to check link status is in Platform specific PCIe
wrapper. Add support for platform specific drivers to add callback
functions for the PCIe Cadence core to start link and verify link status.
Link: https://lore.kernel.org/r/20200722110317.4744-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Certain platforms like TI's J721E using Cadence PCIe IP can perform only
32-bit accesses for reading or writing to Cadence registers. Convert all
read and write accesses to 32-bit in Cadence PCIe driver in preparation
for adding PCIe support in TI's J721E SoC.
Also add spin lock to disable interrupts while modifying PCI_STATUS
register while raising legacy interrupt since PCI_STATUS is accessible
by both remote RC and EP and time between read and write should be
minimized.
Link: https://lore.kernel.org/r/20200722110317.4744-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit bd22885aa1 ("PCI: cadence: Refactor driver to use as a core
library") while refactoring the Cadence PCIe driver to be used as
library, removed pm_runtime_get_sync() from cdns_pcie_ep_setup()
and cdns_pcie_host_setup() but missed to remove the corresponding
pm_runtime_put_sync() in the error path. Fix it here.
Link: https://lore.kernel.org/r/20200722110317.4744-3-kishon@ti.com
Fixes: bd22885aa1 ("PCI: cadence: Refactor driver to use as a core library")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cadence PCIe core driver (host mode) uses "cdns,no-bar-match-nbits"
property to configure the number of bits passed through from PCIe
address to internal address in Inbound Address Translation register.
This only used the NO MATCH BAR.
However standard PCI dt-binding already defines "dma-ranges" to
describe the address ranges accessible by PCIe controller. Add support
in Cadence PCIe host driver to parse dma-ranges and configure the
inbound regions for BAR0, BAR1 and NO MATCH BAR. Cadence IP specifies
maximum size for BAR0 as 256GB, maximum size for BAR1 as 2 GB.
This adds support to take the next biggest region in "dma-ranges" and
find the smallest BAR that each of the regions fit in and if there is
no BAR big enough to hold the region, split the region to see if it can
be fitted using multiple BARs.
"dma-ranges" of J721E will be
dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
Since there is no BAR which can hold 2^48 size, NO_MATCH_BAR will be
used here.
Legacy device tree binding compatibility is maintained by retaining
support for "cdns,no-bar-match-nbits".
Link: https://lore.kernel.org/r/20200722110317.4744-2-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Kdump could fail sometime on Hyper-V guest because the retry in
hv_pci_enter_d0() releases child device structures in hv_pci_bus_exit().
Although there is a second asynchronous device relations message sending
from the host, if this message arrives to the guest after
hv_send_resource_allocated() is called, the retry would fail.
Fix the problem by moving retry to hv_pci_probe() and start the retry
from hv_pci_query_relations() call. This will cause a device relations
message to arrive to the guest synchronously; the guest would then be
able to rebuild the child device structures before calling
hv_send_resource_allocated().
Link: https://lore.kernel.org/r/20200727071731.18516-1-weh@microsoft.com
Fixes: c81992e7f4 ("PCI: hv: Retry PCI bus D0 entry on invalid device state")
Signed-off-by: Wei Hu <weh@microsoft.com>
[lorenzo.pieralisi@arm.com: fixed a comment and commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200722022514.1283916-16-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
There's no need to store the bus number or range resource as the driver
only needs the bus number which is already in the pci_host_bridge.
For endpoint mode, the bus number is always 0.
Link: https://lore.kernel.org/r/20200722022514.1283916-14-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Instead of parsing 'ranges' from DT again, use the bridge window
resources.
Link: https://lore.kernel.org/r/20200722022514.1283916-13-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Most host drivers only parse the DT bus range to set the root bus number
in pci_host_bridge.busnr. The ones that don't set busnr are buggy in
that they ignore what's in DT. Let's set busnr in pci_scan_root_bus_bridge()
where we already check for the bus resource and remove setting it in
host drivers.
Link: https://lore.kernel.org/r/20200722022514.1283916-12-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Will Deacon <will@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-tegra@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Link: https://lore.kernel.org/r/20200722022514.1283916-11-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-renesas-soc@vger.kernel.org
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Also, bridge->busnr is never set so effectively the root bus must be 0.
This will be fixed by a subsequent commit.
Link: https://lore.kernel.org/r/20200722022514.1283916-10-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
There was also a bug that the root_busno is never set which means the
root bus number is always 0 even if the DT said something else.
Link: https://lore.kernel.org/r/20200722022514.1283916-9-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
There was also a bug that the pci_host_bridge.busnr is set from
root_busno, but root_busno is never set which means the root bus number
is always 0 even if the DT said something else.
Link: https://lore.kernel.org/r/20200722022514.1283916-8-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Link: https://lore.kernel.org/r/20200722022514.1283916-7-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Link: https://lore.kernel.org/r/20200722022514.1283916-6-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Link: https://lore.kernel.org/r/20200722022514.1283916-5-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The struct pci_host_bridge is 0 initialized when allocated, so there's
no need to explicitly set fields to 0.
Link: https://lore.kernel.org/r/20200722022514.1283916-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The host bridge's parent device is always the platform device. As we
already have a pointer to it in the devres functions, let's initialize
the parent device. Drivers can still override the parent if desired.
Link: https://lore.kernel.org/r/20200722022514.1283916-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
PCI_ENABLE_PROC_DOMAINS is only used on powerpc and doesn't do anything
for the Versatile host driver, so let's drop it. I'm not sure how or why
I had this to begin with. PCI_ENABLE_PROC_DOMAINS was never used on ARM.
Link: https://lore.kernel.org/r/20200722022514.1283916-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
devm_pci_remap_cfg_resource() will print an error message by itself when
goes wrong, so remove the duplicate error message.
Link: https://lore.kernel.org/r/20200526150954.4729-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when the call returns an error code. Thus a corresponding decrement is
needed on the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200709064356.8800-1-dinghao.liu@zju.edu.cn
Fixes: 0df6150e7c ("PCI: rcar: Use runtime PM to control controller clock")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Commit 711419e504 ("irqdomain: Add the missing assignment of
domain->fwnode for named fwnode") unintentionally caused a dangling pointer
page fault issue on firmware nodes that were freed after IRQ domain
allocation. Commit e3beca48a4 fixed that dangling pointer issue by only
freeing the firmware node after an IRQ domain allocation failure. That fix
no longer frees the firmware node immediately, but leaves the firmware node
allocated after the domain is removed.
The firmware node must be kept around through irq_domain_remove, but should be
freed it afterwards.
Add the missing free operations after domain removal where where appropriate.
Fixes: e3beca48a4 ("irqdomain/treewide: Keep firmware node unconditionally allocated")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # drivers/pci
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1595363169-7157-1-git-send-email-jonathan.derrick@intel.com
When there is no PCIe card connected and advk_pcie_rd_conf() or
advk_pcie_wr_conf() is called for PCI bus which doesn't belong to emulated
root bridge, the aardvark driver throws the following error message:
advk-pcie d0070000.pcie: config read/write timed out
Obviously accessing PCIe registers of disconnected card is not possible.
Extend check in advk_pcie_valid_device() function for validating
availability of PCIe bus. If PCIe link is down, then the device is marked
as Not Found and the driver does not try to access these registers.
This is just an optimization to prevent accessing PCIe registers when card
is disconnected. Trying to access PCIe registers of disconnected card does
not cause any crash, kernel just needs to wait for a timeout. So if card
disappear immediately after checking for PCIe link (before accessing PCIe
registers), it does not cause any problems.
Link: https://lore.kernel.org/r/20200702083036.12230-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to the datasheet of Loongson LS7A bridge chip, the old version
of Loongson LS7A PCIE port has a wrong value about PCI class which is
0x060000, the correct value should be 0x060400, this bug can be fixed by
"dev->class = PCI_CLASS_BRIDGE_PCI << 8;" at the software level and it
was fixed in hardware in the latest LS7A versions.
In order to maintain downward compatibility, use DECLARE_PCI_FIXUP_EARLY
instead of DECLARE_PCI_FIXUP_HEADER for bridge_class_quirk() to fix it as
early as possible.
Otherwise, in the function pci_setup_device(), the related code about
"dev->class" such as "class = dev->class >> 8;" and "dev->transparent
= ((dev->class & 0xff) == 1);" maybe get wrong value without EARLY fixup.
Link: https://lore.kernel.org/r/1595065176-460-1-git-send-email-yangtiezhu@loongson.cn
Fixes: 1f58cca5cf ("PCI: Add Loongson PCI Controller support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
As reported in https://bugzilla.kernel.org/206217 , raw_violation_fixup
is causing more harm than good in some common use-cases.
This patch is a partial revert of commit:
191cd6fb5d ("PCI: tegra: Add SW fixup for RAW violations")
and fixes the following regression since then.
* Description:
When both the NIC and MMC are used one can see the following message:
NETDEV WATCHDOG: enp1s0 (r8169): transmit queue 0 timed out
and
pcieport 0000:00:02.0: AER: Uncorrected (Non-Fatal) error received: 0000:01:00.0
r8169 0000:01:00.0: AER: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID)
r8169 0000:01:00.0: AER: device [10ec:8168] error status/mask=00004000/00400000
r8169 0000:01:00.0: AER: [14] CmpltTO (First)
r8169 0000:01:00.0: AER: can't recover (no error_detected callback)
pcieport 0000:00:02.0: AER: device recovery failed
After that, the ethernet NIC is not functional anymore even after
reloading the r8169 module. After a reboot, this is reproducible by
copying a large file over the NIC to the MMC.
For some reason this is not reproducible when files are copied to a tmpfs.
* Little background on the fixup, by Manikanta Maddireddy:
"In the internal testing with dGPU on Tegra124, CmplTO is reported by
dGPU. This happened because FIFO queue in AFI(AXI to PCIe) module
get full by upstream posted writes. Back to back upstream writes
interleaved with infrequent reads, triggers RAW violation and CmpltTO.
This is fixed by reducing the posted write credits and by changing
updateFC timer frequency. These settings are fixed after stress test.
In the current case, RTL NIC is also reporting CmplTO. These settings
seems to be aggravating the issue instead of fixing it."
Link: https://lore.kernel.org/r/20200718100710.15398-1-kwizart@gmail.com
Fixes: 191cd6fb5d ("PCI: tegra: Add SW fixup for RAW violations")
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Cc: stable@vger.kernel.org
Use devm_platform_ioremap_resource_byname() to simplify the code
since it contains platform_get_resource_byname() and
devm_ioremap_resource() respectively.
Link: https://lore.kernel.org/r/20200708164013.5076-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Quite some non OF/ACPI users of irqdomains allocate firmware nodes of type
IRQCHIP_FWNODE_NAMED or IRQCHIP_FWNODE_NAMED_ID and free them right after
creating the irqdomain. The only purpose of these FW nodes is to convey
name information. When this was introduced the core code did not store the
pointer to the node in the irqdomain. A recent change stored the firmware
node pointer in irqdomain for other reasons and missed to notice that the
usage sites which do the alloc_fwnode/create_domain/free_fwnode sequence
are broken by this. Storing a dangling pointer is dangerous itself, but in
case that the domain is destroyed later on this leads to a double free.
Remove the freeing of the firmware node after creating the irqdomain from
all affected call sites to cure this.
Fixes: 711419e504 ("irqdomain: Add the missing assignment of domain->fwnode for named fwnode")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/873661qakd.fsf@nanos.tec.linutronix.de
According to the Armada XP datasheet, section 10.2.6: "in order for
the device to do a write to the MSI doorbell address, it needs to write
to a register in the internal registers space".
As a result of the requirement above, without this patch, MSI won't
function and therefore some devices won't operate properly without
pci=nomsi.
This requirement was not present at the time of writing this driver
since the vendor u-boot always initializes all PCIe controllers
(incl. BAR0 initialization) and for some time, the vendor u-boot was
the only available bootloader for this driver's SoCs (e.g. A38x,A37x,
etc).
Tested on an Armada 385 board on mainline u-boot (2020.4), without
u-boot PCI initialization and the following PCIe devices:
- Wilocity Wil6200 rev 2 (wil6210)
- Qualcomm Atheros QCA6174 (ath10k_pci)
Both failed to get a response from the device after loading the
firmware and seem to operate properly with this patch.
Link: https://lore.kernel.org/r/20200623060334.108444-1-sh@tkos.co.il
Signed-off-by: Shmuel Hazan <sh@tkos.co.il>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Use devm_platform_ioremap_resource() to simplify the code, since t
contains platform_get_resource() and devm_ioremap_resource() calls
respectively.
Link: https://lore.kernel.org/r/20200708155614.308-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Use devm_platform_ioremap_resource_byname() to simplify the code,
since it calls respectively platform_get_resource_byname() and
devm_ioremap_resource().
Link: https://lore.kernel.org/r/20200602171601.17630-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The xilinx host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
The only difference is pci_assign_unassigned_bus_resources() was called
instead of pci_bus_size_bridges() and pci_bus_assign_resources(). This
should be the same.
Link: https://lore.kernel.org/r/20200522234832.954484-16-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Michal Simek <michal.simek@xilinx.com>
The xilinx-nwl host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
The only difference is pci_assign_unassigned_bus_resources() was called
instead of pci_bus_size_bridges() and pci_bus_assign_resources(). This
should be the same.
Link: https://lore.kernel.org/r/20200522234832.954484-15-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Michal Simek <michal.simek@xilinx.com>
The rockchip host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-14-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
The rcar host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-13-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
The iproc host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
The only difference is pci_assign_unassigned_bus_resources() was called
instead of pci_bus_size_bridges() and pci_bus_assign_resources(). This
should be the same.
Link: https://lore.kernel.org/r/20200522234832.954484-12-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
The altera host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
The only difference is pci_assign_unassigned_bus_resources() was called
instead of pci_bus_size_bridges() and pci_bus_assign_resources(). This
should be the same.
Link: https://lore.kernel.org/r/20200522234832.954484-11-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: rfi@lists.rocketboards.org
The xgene host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-10-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Toan Le <toan@os.amperecomputing.com>
The versatile host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-9-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The v3 host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-8-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
The tegra host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-7-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The mobiveil host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-6-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
The brcmstb host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-5-robh@kernel.org
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-rpi-kernel@lists.infradead.org
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200522234832.954484-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will@kernel.org>
Lots of define are actually already defined in pci_regs.h, directly use
the standard defines.
Link: https://lore.kernel.org/r/20200615210608.21469-13-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Some SoC based on ipq8064/5 needs to be limited to pci GEN1 speed due to
some hardware limitations. Add support for speed setting defined by the
max-link-speed binding. If not defined the max speed is set to GEN2 by
default.
Link: https://lore.kernel.org/r/20200615210608.21469-12-ansuelsmth@gmail.com
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Ipq8064-v2 have tx term offset set to 0. Introduce this variant to permit
different offset based on the revision.
Link: https://lore.kernel.org/r/20200615210608.21469-10-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Add tx term offset support to pcie qcom driver need in some revision of
the ipq806x SoC. Ipq8064 needs tx term offset set to 7.
Link: https://lore.kernel.org/r/20200615210608.21469-9-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.5+
Set some specific value for Tx De-Emphasis, Tx Swing and Rx equalization
needed on some ipq8064 based device (Netgear R7800 for example). Without
this the system locks on kernel load.
Link: https://lore.kernel.org/r/20200615210608.21469-8-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.5+
Rework 2.1.0 revision to use bulk clk api and fix missing assert on
reset_control_deassert error.
Link: https://lore.kernel.org/r/20200615210608.21469-7-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The deinit issues reset_control_assert for PCI twice and does not contain
phy reset.
Link: https://lore.kernel.org/r/20200615210608.21469-4-ansuelsmth@gmail.com
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Aux and Ref clk are missing in PCIe qcom driver. Add support for this
optional clks for ipq8064/apq8064 SoC.
Link: https://lore.kernel.org/r/20200615210608.21469-2-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Most callers of config read do not check for return value. But most of the
ones that do, checks for error indication in 'val' variable.
This patch updates error handling in advk_pcie_rd_conf() function. If PIO
transfer fails then 'val' variable is set to 0xffffffff which indicates
failture.
Link: https://lore.kernel.org/r/20200528162604.GA323482@bjorn-Precision-5520
Link: https://lore.kernel.org/r/20200601130315.18895-1-pali@kernel.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, thus a matching decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200707055000.9453-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200520090253.2761-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200520084756.31620-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
VMD device 28C0 natively assists guest passthrough of the VMD endpoint
through the use of shadow registers that provide Host Physical Addresses
to correctly assign bridge windows. These shadow registers are only
available if VMD config space register 0x70, bit 1 is set.
In order to support this mode in existing VMD devices which don't
natively support the shadow register, it was decided that the hypervisor
could offer the shadow registers in a vendor-specific PCI capability.
QEMU has been modified to create this vendor-specific capability and
supply the shadow membar registers for VMDs which don't natively support
this feature. This patch adds this mode and updates the supported device
list to allow this feature to be used on these VMDs.
Link: https://lore.kernel.org/r/20200528030240.16024-4-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200522234832.954484-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200522234832.954484-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Replace http:// links with https:// links. This reduces the likelihood of
man-in-the-middle attacks when developers open these links.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
[bhelgaas: also update samsung.com links, drop sourceforge link]
Link: https://lore.kernel.org/r/20200627103050.71712-1-grandmaster@al2klimov.de
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- Release resource in probe failure path (Wei Hu)
- Retry PCI bus D0 entry if device state is invalid (Wei Hu)
- Use struct_size() to help avoid type mistakes (Gustavo A. R. Silva)
* remotes/lorenzo/pci/hv:
PCI: hv: Use struct_size() helper
PCI: hv: Retry PCI bus D0 entry on invalid device state
PCI: hv: Fix the PCI HyperV probe failure path to release resource properly
- Constify struct pci_ecam_ops (Rob Herring)
- Support building as modules (Rob Herring)
- Eliminate wrappers for pci_host_common_probe() by using DT match table
data (Rob Herring)
* remotes/lorenzo/pci/host-generic:
PCI: host-generic: Eliminate pci_host_common_probe wrappers
PCI: host-generic: Support building as modules
PCI: Constify struct pci_ecam_ops
# Conflicts:
# drivers/pci/controller/dwc/pcie-hisi.c
- Deprecate 'cdns,max-outbound-regions' and 'cdns,no-bar-match-nbits'
bindings in favor of deriving them from 'ranges' and 'dma-ranges'
(Kishon Vijay Abraham I)
- Read Vendor and Device ID as 32 bits (not 16) from DT (Kishon Vijay
Abraham I)
* remotes/lorenzo/pci/cadence:
PCI: cadence: Fix to read 32-bit Vendor ID/Device ID property from DT
PCI: cadence: Remove "cdns,max-outbound-regions" DT property
dt-bindings: PCI: cadence: Deprecate inbound/outbound specific bindings
- Train link immediately after enabling link training to avoid issues
with Compex WLE900VX and Turris MOX devices (Pali Rohár)
- Remove ASPM config and let the PCI core do it (Pali Rohár)
- Interpret zero 'max-link-speed' value as invalid (Pali Rohár)
- Respect the 'max-link-speed' property and improve link training (Marek
Behún)
- Issue PERST via GPIO (Pali Rohár)
- Add PHY support (Marek Behún)
- Use standard PCIe capability macros (Pali Rohár)
- Document new 'max-link-speed', 'phys', and 'reset-gpios' properties
(Marek Behún)
* remotes/lorenzo/pci/aardvark:
dt-bindings: PCI: aardvark: Describe new properties
PCI: aardvark: Replace custom macros by standard linux/pci_regs.h macros
PCI: aardvark: Add PHY support
PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access
PCI: aardvark: Issue PERST via GPIO
PCI: aardvark: Improve link training
PCI: of: Zero max-link-speed value is invalid
PCI: aardvark: Don't blindly enable ASPM L0s and don't write to read-only register
PCI: aardvark: Train link immediately after enabling training
- Clarify that platform_get_irq() should never return 0 (Bjorn Helgaas)
- Check for platform_get_irq() failure consistently (Bjorn Helgaas)
- Replace zero-length array with flexible-array (Gustavo A. R. Silva)
- Unify pcie_find_root_port() and pci_find_pcie_root_port() (Yicong Yang)
- Quirk Intel C620 MROMs, which have non-BARs in BAR locations (Xiaochun
Lee)
- Fix pcie_pme_resume() and pcie_pme_remove() kernel-doc (Jay Fang)
- Rename _DSM constants to align with spec (Krzysztof Wilczyński)
* pci/misc:
PCI: Rename _DSM constants to align with spec
PCI/PME: Fix kernel-doc of pcie_pme_resume() and pcie_pme_remove()
x86/PCI: Mark Intel C620 MROMs as having non-compliant BARs
PCI: Unify pcie_find_root_port() and pci_find_pcie_root_port()
PCI: Replace zero-length array with flexible-array
PCI: Check for platform_get_irq() failure consistently
driver core: platform: Clarify that IRQ 0 is invalid
Add driver for the Socionext UniPhier Pro5 SoC endpoint controller.
This controller is based on the DesignWare PCIe core.
And add "host" to existing controller descriontions for the host controller
in Kconfig.
Link: https://lore.kernel.org/r/1589457801-12796-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl7WhbkTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXlUnB/0R8dBVSeRfNmyJaadBWKFc/LffwKLD
CQ8PVv22ffkCaEYV2tpnhS6NmkERLNdson4Uo02tVUsjOJ4CrWHTn7aKqYWZyA+O
qv/PiD9TBXJVYMVP2kkyaJlK5KoqeAWBr2kM16tT0cxQmlhE7g0Xo2wU9vhRbU+4
i4F0jffe4lWps65TK392CsPr6UEv1HSel191Py5zLzYqChT+L8WfahmBt3chhsV5
TIUJYQvBwxecFRla7yo+4sUn37ZfcTqD1hCWSr0zs4psW0ge7d80kuaNZS+EqxND
fGm3Bp1BlUuDKsJ/D+AaHLCR47PUZ9t9iMDjZS/ovYglLFwi+h3tAV+W
=LwVR
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyper-v updates from Wei Liu:
- a series from Andrea to support channel reassignment
- a series from Vitaly to clean up Vmbus message handling
- a series from Michael to clean up and augment hyperv-tlfs.h
- patches from Andy to clean up GUID usage in Hyper-V code
- a few other misc patches
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (29 commits)
Drivers: hv: vmbus: Resolve more races involving init_vp_index()
Drivers: hv: vmbus: Resolve race between init_vp_index() and CPU hotplug
vmbus: Replace zero-length array with flexible-array
Driver: hv: vmbus: drop a no long applicable comment
hyper-v: Switch to use UUID types directly
hyper-v: Replace open-coded variant of %*phN specifier
hyper-v: Supply GUID pointer to printf() like functions
hyper-v: Use UUID API for exporting the GUID (part 2)
asm-generic/hyperv: Add definitions for Get/SetVpRegister hypercalls
x86/hyperv: Split hyperv-tlfs.h into arch dependent and independent files
x86/hyperv: Remove HV_PROCESSOR_POWER_STATE #defines
KVM: x86: hyperv: Remove duplicate definitions of Reference TSC Page
drivers: hv: remove redundant assignment to pointer primary_channel
scsi: storvsc: Re-init stor_chns when a channel interrupt is re-assigned
Drivers: hv: vmbus: Introduce the CHANNELMSG_MODIFYCHANNEL message type
Drivers: hv: vmbus: Synchronize init_vp_index() vs. CPU hotplug
Drivers: hv: vmbus: Remove the unused HV_LOCALIZED channel affinity logic
PCI: hv: Prepare hv_compose_msi_msg() for the VMBus-channel-interrupt-to-vCPU reassignment functionality
Drivers: hv: vmbus: Use a spin lock for synchronizing channel scheduling vs. channel removal
hv_utils: Always execute the fcopy and vss callbacks in a tasklet
...
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Also, call pm_runtime_disable() when pm_runtime_get_sync() returns
an error code.
Link: https://lore.kernel.org/r/20200521024709.2368-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Versions of VMD with the Host Physical Address shadow register use this
register to calculate the bus address offset needed to do guest
passthrough of the domain. This register shadows the Host Physical
Address registers including the resource type bits. After calculating
the offset, the extra resource type bits lead to the VMD resources being
over-provisioned at the front and under-provisioned at the back.
Example:
pci 10000:80:02.0: reg 0x10: [mem 0xf801fffc-0xf803fffb 64bit]
Expected:
pci 10000:80:02.0: reg 0x10: [mem 0xf8020000-0xf803ffff 64bit]
If other devices are mapped in the over-provisioned front, it could lead
to resource conflict issues with VMD or those devices.
Link: https://lore.kernel.org/r/20200528030240.16024-3-jonathan.derrick@intel.com
Fixes: a1a3017013 ("PCI: vmd: Fix shadow offsets to reflect spec changes")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200521031355.7022-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct hv_dr_state {
...
struct hv_pcidev_description func[];
};
struct pci_bus_relations {
...
struct pci_function_description func[];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following forms:
offsetof(struct hv_dr_state, func) +
(sizeof(struct hv_pcidev_description) *
(relations->device_count))
offsetof(struct pci_bus_relations, func) +
(sizeof(struct pci_function_description) *
(bus_rel->device_count))
with:
struct_size(dr, func, relations->device_count)
and
struct_size(bus_rel, func, bus_rel->device_count)
respectively.
Link: https://lore.kernel.org/r/20200525164319.GA13596@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
This controller can be found on Loongson-2K SoC, Loongson-3
systems with RS780E/LS7A PCH.
The RS780E part of code was previously located at
arch/mips/pci/ops-loongson3.c and now it can use generic PCI
driver implementation.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
No functional change. Get "struct pcie_port *" from private data
pointer of "struct irq_domain" in dw_pcie_irq_domain_free() to make
it look similar to how "struct pcie_port *" is obtained in
dw_pcie_irq_domain_alloc()
Link: https://lore.kernel.org/r/20191220100550.777-1-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The vim3l board does not work with a standard PCIe switch (ASM1184e),
spitting all kind of errors - hinting at HW misconfiguration (no link,
port enumeration issues, etc).
According to the the Synopsys DWC PCIe Reference Manual, in the section
dedicated to the PLCR register, bit 7 is described (FAST_LINK_MODE) as:
"Sets all internal timers to fast mode for simulation purposes."
it is sound to set this bit from a simulation perspective, but on actual
silicon, which expects timers to have a nominal value, it is not.
Make sure the FAST_LINK_MODE bit is cleared when configuring the RC
to solve this problem.
Link: https://lore.kernel.org/r/20200429164230.309922-1-maz@kernel.org
Fixes: 9c0ef6d34f ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
On a system that uses the internal DWC MSI widget, I get this
warning from debugfs when CONFIG_GENERIC_IRQ_DEBUGFS is selected:
debugfs: File ':soc:pcie@fc000000' in directory 'domains' already present!
This is due to the fact that the DWC MSI code tries to register two
IRQ domains for the same firmware node, without telling the low
level code how to distinguish them (by setting a bus token). This
further confuses debugfs which tries to create corresponding
files for each domain.
Fix it by tagging the inner domain as DOMAIN_BUS_NEXUS, which is
the closest thing we have as to "generic MSI".
Link: https://lore.kernel.org/r/20200501113921.366597-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
platform_get_resource() may fail and return NULL, so we had better
check its return value to avoid a NULL pointer dereference a bit later
in the code. Fix it to use devm_platform_ioremap_resource_byname()
instead of calling platform_get_resource_byname() and devm_ioremap().
Link: https://lore.kernel.org/r/20200429015027.134485-1-weiyongjun1@huawei.com
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix the following sparse warning:
drivers/pci/controller/dwc/pcie-intel-gw.c:456:5: warning: symbol
'intel_pcie_cpu_addr' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20200415084953.6533-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Function dw_pcie_prog_outbound_atu_unroll() does not program the upper
32-bit ATU limit register. Since ATU programming functions limit the
size of the translated region to 4GB by using a u32 size parameter,
these issues may combine into undefined behavior for resource sizes
with non-zero upper 32-bits.
For example, a 128GB address space starting at physical CPU address of
0x2000000000 with size of 0x2000000000 needs the following values
programmed into the lower and upper 32-bit limit registers:
0x3fffffff in the upper 32-bit limit register
0xffffffff in the lower 32-bit limit register
Currently, only the lower 32-bit limit register is programmed with a
value of 0xffffffff but the upper 32-bit limit register is not being
programmed. As a result, the upper 32-bit limit register remains at its
default value after reset of 0x0.
These issues may combine to produce undefined behavior since the ATU
limit address may be lower than the ATU base address. Programming the
upper ATU limit address register prevents such undefined behavior despite
the region size getting truncated due to the 32-bit size limit.
Link: https://lore.kernel.org/r/1585785493-23210-1-git-send-email-alan.mikhak@sifive.com
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
R-Car PCIe controller has support to map multiple memory regions for
mapping the outbound memory in local system also the controller limits
single allocation for each region (that is, once a chunk is used from the
region it cannot be used to allocate a new one). This features inspires to
add support for handling multiple memory bases in endpoint framework.
With this patch pci_epc_mem_init() initializes address space for endpoint
controller which support single window and pci_epc_multi_mem_init()
initializes multiple windows supported by endpoint controller.
Link: https://lore.kernel.org/r/1588854799-13710-6-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The PCI Bus Binding specification (IEEE Std 1275-1994 Revision 2.1 [1])
defines both Vendor ID and Device ID to be 32-bits. Fix
pcie-cadence-host.c driver to read 32-bit Vendor ID and Device ID
properties from device tree.
[1] -> https://www.devicetree.org/open-firmware/bindings/pci/pci2_1.pdf
Link: https://lore.kernel.org/r/20200508130646.23939-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tom Joseph <tjoseph@cadence.com>
"cdns,max-outbound-regions" device tree property provides the
maximum number of outbound regions supported by the Host PCIe
controller. However the outbound regions are configured based
on what is populated in the "ranges" DT property.
Avoid using two properties for configuring outbound regions and
use only "ranges" property instead.
Link: https://lore.kernel.org/r/20200508130646.23939-3-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tom Joseph <tjoseph@cadence.com>
PCI-E capability macros are already defined in linux/pci_regs.h.
Remove their reimplementation in pcie-aardvark.
Link: https://lore.kernel.org/r/20200430080625.26070-9-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With recent proposed changes for U-Boot it is possible that bootloader
won't initialize the PHY for this controller (currently the PHY is
initialized regardless whether PCI is used in U-Boot, but with these
proposed changes the PHY is initialized only on request).
Since the mvebu-a3700-comphy driver by Miquèl Raynal supports enabling
PCIe PHY, and since Linux' functionality should be independent on what
bootloader did, add code for enabling generic PHY if found in device OF
node.
The mvebu-a3700-comphy driver does PHY powering via SMC calls to ARM
Trusted Firmware. The corresponding code in ARM Trusted Firmware skips
one register write which U-Boot does not: step 7 ("Enable TX"), see [1].
Instead ARM Trusted Firmware expects PCIe driver to do this step,
probably because the register is in PCIe controller address space,
instead of PHY address space. We therefore add this step into the
advk_pcie_setup_hw function.
[1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/tree/drivers/marvell/comphy/phy-comphy-3700.c?h=v2.3-rc2#n836
Link: https://lore.kernel.org/r/20200430080625.26070-8-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquèl Raynal <miquel.raynal@bootlin.com>
This register is applicable only when the controller is configured for
Endpoint mode, which is not the case for the current version of this
driver.
Attempting to remove this code though caused some ath10k cards to stop
working, so for some unknown reason it is needed here.
This should be investigated and a comment explaining this should be put
before the code, so we add a FIXME comment for now.
Link: https://lore.kernel.org/r/20200430080625.26070-7-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for issuing PERST via GPIO specified in 'reset-gpios'
property (as described in PCI device tree bindings).
Some buggy cards (e.g. Compex WLE900VX or WLE1216) are not detected
after reboot when PERST is not issued during driver initialization.
If bootloader already enabled link training then issuing PERST has no
effect for some buggy cards (e.g. Compex WLE900VX) and these cards are
not detected. We therefore clear the LINK_TRAINING_EN register before.
It was observed that Compex WLE900VX card needs to be in PERST reset
for at least 10ms if bootloader enabled link training.
Tested on Turris MOX.
Link: https://lore.kernel.org/r/20200430080625.26070-6-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the aardvark driver trains link in PCIe gen2 mode. This may
cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
even not detected. Moreover when ASPM code tries to retrain link second
time, these cards may stop responding and link goes down. If gen1 is
used this does not happen.
Unconditionally forcing gen1 is not a good solution since it may have
performance impact on gen2 cards.
To overcome this, read 'max-link-speed' property (as defined in PCI
device tree bindings) and use this as max gen mode. Then iteratively try
link training at this mode or lower until successful. After successful
link training choose final controller gen based on Negotiated Link Speed
from Link Status register, which should match card speed.
Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Trying to change Link Status register does not have any effect as this
is a read-only register. Trying to overwrite bits for Negotiated Link
Width does not make sense.
In future proper change of link width can be done via Lane Count Select
bits in PCIe Control 0 register.
Trying to unconditionally enable ASPM L0s via ASPM Control bits in Link
Control register is wrong. There should be at least some detection if
endpoint supports L0s as isn't mandatory.
Moreover ASPM Control bits in Link Control register are controlled by
pcie/aspm.c code which sets it according to system ASPM settings,
immediately after aardvark driver probes. So setting these bits by
aardvark driver has no long running effect.
Remove code which touches ASPM L0s bits from this driver and let
kernel's ASPM implementation to set ASPM state properly.
Some users are reporting issues that this code is problematic for some
Intel wifi cards and removing it fixes them, see e.g.:
https://bugzilla.kernel.org/show_bug.cgi?id=196339
If problems with Intel wifi cards occur even after this commit, then
pcie/aspm.c code could be modified / hooked to not enable ASPM L0s state
for affected problematic cards.
Link: https://lore.kernel.org/r/20200430080625.26070-3-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adding even 100ms (PCI_PM_D3COLD_WAIT) delay between enabling link
training and starting link training causes detection issues with some
buggy cards (such as Compex WLE900VX).
Move the code which enables link training immediately before the one
which starts link traning.
This fixes detection issues of Compex WLE900VX card on Turris MOX after
cold boot.
Link: https://lore.kernel.org/r/20200430080625.26070-2-pali@kernel.org
Fixes: f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready...")
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
xHCI's PCI fixup, run at the end of pcie-brcmstb's probe, depends on
RPi4's VideoCore firmware interface to be up and running. It's possible
for both initializations to race, so make sure it's available prior to
starting.
Link: https://lore.kernel.org/r/20200505161318.26200-4-nsaenzjulienne@suse.de
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The platform_get_irq*() interfaces return either a negative error number or
a valid IRQ. 0 is not a valid return value, so check for "< 0" to detect
failure as recommended by the function documentation.
On failure, return the error number from platform_get_irq*() instead of
making up a new one.
Link: https://lore.kernel.org/r/cover.1583952275.git.amanharitsh123@gmail.com
[bhelgaas: commit log, squash into one patch]
Signed-off-by: Aman Sharma <amanharitsh123@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
When kdump is triggered, some PCI devices may have not been shut down
cleanly before the kdump kernel starts.
This causes the initial attempt to enter D0 state in the kdump kernel to
fail with invalid device state returned from Hyper-V host.
When this happens, explicitly call hv_pci_bus_exit() and retry to enter
the D0 state.
Link: https://lore.kernel.org/r/20200507050300.10974-1-weh@microsoft.com
Signed-off-by: Wei Hu <weh@microsoft.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
In some error cases in hv_pci_probe(), allocated resources are not freed.
Fix this by adding a field to keep track of the high water mark for slots
that have resources allocated to them. In case of an error, this high
water mark is used to know which slots have resources that must be released.
Since slots are numbered starting with zero, a value of -1 indicates no
slots have been allocated resources. There may be unused slots in the range
between slot 0 and the high water mark slot, but these slots are already
ignored by the existing code in the allocate and release loops with the call
to get_pcichild_wslot().
Link: https://lore.kernel.org/r/20200507050211.10923-1-weh@microsoft.com
Signed-off-by: Wei Hu <weh@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Some informal internal experiments has shown that the BrcmSTB ASPM L0s
savings may introduce an undesirable noise signal on some customers'
boards. In addition, L0s was found lacking in realized power savings,
especially relative to the L1 ASPM component. This is BrcmSTB's
experience and may not hold for others. At any rate, if the
'aspm-no-l0s' property is present L0s will be disabled.
Link: https://lore.kernel.org/r/20200507201544.43432-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
The outbound memory window registers were being referenced
with an incorrect stride offset. This probably wasn't noticed
previously as there was likely only one such window employed.
Link: https://lore.kernel.org/r/20200507201544.43432-3-james.quinlan@broadcom.com
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
clk_put() was being invoked on a clock obtained by
devm_clk_get_optional().
Link: https://lore.kernel.org/r/20200507201544.43432-2-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
While preparing the driver for upstream this detail was missed.
If not asserted during the initialization process, devices connected on
the bus will not be made aware of the internal reset happening. This,
potentially resulting in unexpected behavior.
Link: https://lore.kernel.org/r/20200507172020.18000-1-nsaenzjulienne@suse.de
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
pci_epc_mem_init() internally used page size equal to *PAGE_SIZE* to
manage the address space so instead just pass the page size as a
argument to pci_epc_mem_init().
Also make pci_epc_mem_init() as a C function instead of a macro function
in preparation for adding support for pci-epc-mem core to handle multiple
windows.
Link: https://lore.kernel.org/r/1588854799-13710-5-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The mask value was calculated incorrectly for PCIEPAMR register if the
size was less than 128 bytes. Fix this issue by adding a check on size.
Link: https://lore.kernel.org/r/1588854799-13710-4-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Move shareable code to common file pcie-rcar.c and the #defines to
pcie-rcar.h so that the common code can be reused with endpoint driver.
There are no functional changes with this patch for the host controller
driver.
Link: https://lore.kernel.org/r/1588854799-13710-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
This commit renames pcie-rcar.c to pcie-rcar-host.c in preparation for
adding support for endpoint mode. CONFIG_PCIE_RCAR is kept so that arm64
defconfig change can be a separate patch.
With this patch both config options PCIE_RCAR and PCIE_RCAR_HOST will be
available but PCIE_RCAR internally selects PCIE_RCAR_HOST so that bisect
builds wont be affected.
Link: https://lore.kernel.org/r/1588854799-13710-2-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Error code is stored in rp->reset_gpio and not in err variable.
Link: https://lore.kernel.org/r/20200414102512.27506-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Add suspend/resume support for rcar. The resume handler reprograms the
hardware based on the software state kept in specific device structures,
so there is no need to save registers on suspend.
Link: https://lore.kernel.org/r/20200314191232.3122290-1-marek.vasut@gmail.com
Link: https://lore.kernel.org/r/20200426123148.56051-1-marek.vasut@gmail.com
Signed-off-by: Kazufumi Ikeda <kaz-ikeda@xc.jp.nec.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
The outbound windows (PCIEPAUR(x), PCIEPALR(x)) describe a mapping between
a CPU address (which is determined by the window number 'x') and a
programmed PCI address - Thus allowing the controller to translate CPU
accesses into PCI accesses.
However the existing code incorrectly writes the CPU address - lets fix
this by writing the PCI address instead.
For memory transactions, existing DT users describe a 1:1 identity mapping
and thus this change should have no effect. However the same isn't true for
I/O.
Link: https://lore.kernel.org/r/20191004132941.6660-1-andrew.murray@arm.com
Fixes: c25da47788 ("PCI: rcar: Add Renesas R-Car PCIe driver")
Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Most ECAM host drivers are just different pci_ecam_ops which can be DT
match table data. That's already the case in some cases, but let's
do that for all the ECAM drivers. Then we can use
of_device_get_match_data() in pci_host_common_probe() and eliminate the
probe wrapper functions and use pci_host_common_probe() directly for
probe.
Link: https://lore.kernel.org/r/20200409234923.21598-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: Robert Richter <rrichter@marvell.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
If we fails somewhere in 'v3_pci_probe()', we need to free 'host'.
Use the managed version of 'pci_alloc_host_bridge()' to do that easily.
The use of managed resources is already widely used in this driver.
Link: https://lore.kernel.org/r/20200418081637.1585-1-christophe.jaillet@wanadoo.fr
Fixes: 68a15eb7bd ("PCI: v3-semi: Add V3 Semiconductor PCI host driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following sparse warning:
drivers/pci/controller/dwc/pcie-hisi.c:365:21: warning:
symbol 'hisi_pcie_platform_ops' was not declared. Should it be static?
Link: https://lore.kernel.org/r/1587611883-26960-1-git-send-email-zou_wei@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Commit 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") overcomplicated the computation of the
msix_tbl address. Simplify it as it's simply the addr + offset. Provided
addr is (void *) already.
objdump -d shows no difference after this patch.
Link: https://lore.kernel.org/r/20200420065227.4920-1-jslaby@suse.cz
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Enable building host-generic and its host-common dependency as a
module.
Link: https://lore.kernel.org/r/20200409234923.21598-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Hou Zhiqiang