Because extcon is not allowed for new bindings, and the
dual role switch is supported by USB Role Switch,
especially for Type-C drivers, so register a USB Role
Switch to support the new way
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1567070558-29417-12-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support U3gen2 ISOC transfer upto 96DPs, extend
the data buffer length.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support USB3 Gen2 ISOC, the data buffer length need be extended,
it's hard to make the current qmu_gpd struct compatible, so here
rebuild qmu_gpd struct and make easy to support new QMU format
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support USB3 Gen2 ISOC, the registers of TXCSR1 and RXCSR1
are adjusted to support greater maxpkt and mult value, this
patch fix this issue
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The notifier callbacks of extcon are called in atomic context, but the
callbacks will call regulator_enable()/regulator_disable() which may
sleep caused by mutex, so use work queue to call the sleep functions.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When boot on the platform with the USB cable connected to Win7,
the Win7 will pop up an error dialog: "USB Device not recognized",
but finally the Win7 can enumerate it successfully.
The root cause is as the following:
When the xHCI driver set PORT_POWER of the OTG port, and if both
IDPIN and VBUS_VALID are high at the same time, the MTU3 controller
will set SESSION and pull up DP, so the Win7 can detect existence
of USB device, but if the mtu3 driver can't switch to device mode
during the debounce time, the Win7 can not enumerate it.
Here to fix it by removing the 1s delayed EXTCON register to speed up
mode switch.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The old way of usb wakeup only supports platform with single SSUSB IP,
such as mt8173, but mt2712 has two SSUSB IPs, so rebuild its flow and
also supports the new glue layer of usb wakeup on mt2712 which is
different from mt8173.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support SuperSpeedPlus for usb3.1 device IP
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In order to keep manual DRD switch independent on IDDIG interrupt,
make use of FORCE/RG_IDDIG instead of IDDIG EINT interrupt to
implement manual DRD switch function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
add support for 36-bit DMA address
[ Felipe Balbi: fix printk format for dma_addr_t ]
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are mcu_bus and dma_bus clocks needed to be turned on/off by
driver on some SoCs, so add them as optional ones
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The wakeup debounce clocks for each ports in fact are not
needed, so remove them.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add support to disable specific usb3 ports, it's useful when
usb3 phy is shared with PCIe or SATA, because we should disable
the corresponding usb3 port if the phy is used by PCIe or SATA.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the delayed status handling. This is used by mass storage etc to
gain some extra time to setup its internal status before it can proceed
further requests, and once the gadget is ready, it will enqueue an
empty packet which is used for synchronization.
The issue may happen on some FGPA platform with very low cpu frequency.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The combo of list_empty() and list_first_entry() can be replaced with
list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usually, the reference clock comes from 26M oscillator directly,
but some SoCs are not, add it for compatibility.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
support dual-role mode; there are two ways to switch between
host and device modes, one is by idpin, another is by debugfs
which depends on user input.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
supports host only mode and the code is ported from
host/xhci-mtk.c
IPPC register shared between host and device is moved
into common glue layer.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the MediaTek USB3 controller
integrated into MT8173. It currently supports High-Speed
Peripheral Only mode.
Super-Speed Peripheral, Dual-Role Device and Host Only (xHCI)
modes will be added in the next patchs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chunfeng Yun