e1000e allocates a page per skb fragment. We must account
PAGE_SIZE increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe allocates half a page per skb fragment. We must account
PAGE_SIZE/2 increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000 allocates half a page per skb fragment. We must account
PAGE_SIZE/2 increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000 allocates a full page per skb fragment. We must account PAGE_SIZE
increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2 allocates a full page per fragment. We must account PAGE_SIZE
increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix skb truesize underestimations of this driver.
Each frag truesize is exactly rx_frag_size bytes. (2048 bytes per
default)
A driver should not use "sizeof(struct sk_buff)" at all.
Signed-off-by: Eric Dumazet <eric.dumazet>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb truesize currently accounts for sk_buff struct and part of skb head.
kmalloc() roundings are also ignored.
Considering that skb_shared_info is larger than sk_buff, its time to
take it into account for better memory accounting.
This patch introduces SKB_TRUESIZE(X) macro to centralize various
assumptions into a single place.
At skb alloc phase, we put skb_shared_info struct at the exact end of
skb head, to allow a better use of memory (lowering number of
reallocations), since kmalloc() gives us power-of-two memory blocks.
Unless SLUB/SLUB debug is active, both skb->head and skb_shared_info are
aligned to cache lines, as before.
Note: This patch might trigger performance regressions because of
misconfigured protocol stacks, hitting per socket or global memory
limits that were previously not reached. But its a necessary step for a
more accurate memory accounting.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <ak@linux.intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the driver version to 3.2.10.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds VMDq loopback pf support for i350 devices. The patch
is necessary since the register that enabled loopback was moved and
renamed from DTXSWC to TXSWC.
Signed-off-by: "Akeem G. Abodunrin" <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb_update/validate_nvm_checksum_with_offset() should be static.
Also removes unneeded prototypes for the above functions.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On i350 when traffic is looped back from a VF to the PF the value is byte
swapped from the normal format. In order to address this we need to add a
flag indicating that the ring will need to byte swap the loopback packets
prior to processing them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we mask interrupts in EIMS not in IMS there is no need to re-enable
mask bits in that register. As such we can remove the write to IMS from
the end of igb_msix_other.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change allows support for per packet timesync and global device reset
on the i350 adapter. These features were supported on both 82580 and i350
however it looks like several checks where not updated and as such the i350
support was not enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes certain that one interrupt is always initialized in
igb_request_irq. In addition we drop the use of adapter->pdev and
instead just call pdev since we made a local copy of the pointer earlier in
the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is mostly a drop of unnecessary pointer defines for q_vector when we
don't have issues with line width and don't have multiple references to
the pointer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct a check for change in FCoE priority when IEEE mode DCB is in use.
In IEEE mode a different function has to be used to get the FCoE priority
mask. Also, the check for the mask assumed that only one priority was set.
In case there should be more than one, check just the bit.
These changes help avoid link flapping issues that can come up when IEEE
DCB is in use.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add 2 new counters to ethtool:
1. Count DDP allocation failure since we max the number of buffers
allowed in one DDP context.
2. Count DDP allocation failure since we max the number of buffers
allowed in one DDP context when we alloc an extra buffer.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible for a VF to set an invalid target DMA address in its
Tx/Rx descriptor buffer pointers. The workarounds in this patch
will guard against such an event and issue a VFLR to the VF in response.
The VFLR will shut down the VF until an administrator can take action
to investigate the event and correct the problem.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch exposes the tos value for the TCP sockets when the TOS flag
is requested in the ext_flags for the inet_diag request. This would mainly be
used to expose TOS values for both for TCP and UDP sockets. Currently it is
supported for TCP. When netlink support for UDP would be added the support
to expose the TOS values would alse be done. For IPV4 tos value is exposed
and for IPV6 tclass value is exposed.
Signed-off-by: Murali Raja <muralira@google.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereference doi_def on the line before the NULL check. It has
been this way since 2008. I checked all the callers and doi_def is
always non-NULL here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevents lots of broken frames from showing up on monitor interfaces
by default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: Fix incorrect key_miss handling" changed the code
to only report key miss errors if a MIC error wasn't reported.
When checking the flags in that order in the MAC code, it might miss some
real events, because the value of the MIC error flag is undefined under
some conditions.
The primary issue addressed by the previous commit is making sure that
MIC errors are properly reported on the STA side. This can be fixed in
a better way by adding a separate rx status flag for key miss and
ignoring it for multicast frames.
This fix slightly improves stability in AP mode on some older hardware,
like AR9132.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is unused since the previous dead code that was using it had been
removed earlier.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code for handling various restrictions concerning regulatory limits,
antenna gain, etc. is very convoluted and duplicated across various
EEPROM parsing implementations, making it hard to review.
This patch partially cleans up the mess by unifying regulatory limit
handling in one function and simplifying handling of antenna gain.
It also removes unused transmit power scaling arrays from the EEPROM code,
which belonged to an unimplemented API that isn't supposed to be in
the driver anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY errors relevant for ANI are always tracked by hardware counters, the
bits that allow them to pass through the rx filter are independent of that.
Enabling PHY errors in the rx filter often creates lots of useless DMA traffic
and might be responsible for some of the rx dma stop failure warnings.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't want to report random quality info (new PHYs are affected).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current debug parameter is applied to rtlwifi, which means that all
loaded drivers have the same level of debugging applied. In addition,
the previous method requires a two-step load process to enable debugging.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was another workaround for truesize "bugs".
The reason we did this was that when we orphaned
the SKB it wouldn't be truesize-checked later.
Now that the check is gone (and we just charge
the former smaller size to the socket) there's
no longer a reason to orphan the skb here.
Keep the skb charged to the socket until it is
really freed (or orphaned in TX status). This
helps flow control and allows us to get at the
socket later for other purposes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to adjust truesize.
The history of this was that we always ran into
skb_truesize_bug (via skb_truesize_check) which
has since been removed in commit 92a0acce18.
skb_truesize_check() checked that truesize was
bigger or equal to the actual allocation, which
would trigger in mac80211 due to header adding.
The check no longer exists and we shouldn't be
messing with the truesize anwyay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can now move the radiotap header parsing into
ieee80211_monitor_start_xmit(). This moves it out of
the hotpath, and also helps the code since now the
radiotap header will no longer be present in
ieee80211_xmit() etc. which is easier to understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The purpose of this is two-fold:
1) by moving it out of tx_data.flags, we can in
another patch move the radiotap parsing so it
no longer is in the hotpath
2) if a device implements fragmentation but can
optionally skip it, the radiotap request for
not doing fragmentation may be honoured
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the only way the interface can be a monitor
interface in ieee80211_xmit() is because the frame
came from ieee80211_monitor_start_xmit() we can
move all the code there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add documentation about NOACK tx flag usage.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When tx is suspended temporarily and the queue is flushed, do not increase
the retry count or attempt to send out BAR frames. Instead simply retry
the affected subframes normally after the reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not increment the retry counter if packets to a sleeping station
were not sent because of tx failure, instead of only checking the filter
flag.
Clear the PS filter only after an A-MPDU was reported as filtered,
otherwise the hardware might do some unnecessary extra retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export how many times each of the reset triggers has fired through debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh paths should only exist over established peer links.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If "axq_qnum >= ARRAY_SIZE(sc->tx.txq)", then the call to
ath9k_hw_releasetxqueue() would read beyond the end of the ah->txq[]
array and possibly corrupt memory. Fortunately,
ath9k_hw_setuptxqueue() doesn't return high values of "axq_qnum" and
this code can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
th5k_hw_setup_tx_queue() returns a valid offset into the ah->ah_txq[]
array. The ah->ah_txq[] and the ah->txqs[] array are the same size.
Both have AR5K_NUM_TX_QUEUES elements. So this error handling code
will never trigger.
Also it's wrong. The call to ath5k_hw_release_tx_queue() with a qnum
of AR5K_NUM_TX_QUEUES or more will just trigger a WARN_ON() and
return. Or if it missed the WARN_ON(), it would just corrupt some
memory and return.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I introduced in-kernel off-channel TX I
introduced a bug -- the work can't be canceled
again because the code clear the skb pointer.
Fix this by keeping track separately of whether
TX status has already been reported.
Cc: stable@kernel.org [2.6.38+]
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch for init calib cfg disable a set of calibration for both
init and runtime which cause performance issue, Fix it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed so that offloaded scan can do the
right thing. Without this patch, the no_cck flag
contains random values from the kernel heap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eric Dumazet