Backup Switch Mode controls how the RTC decides when to switch to the
backup power supply. As it is disabled by default, provide a way to enable
and configure it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211018151933.76865-7-alexandre.belloni@bootlin.com
The datasheet for the rv3028 says the weekday has exact 3 bits
and in chapter 3.4.0 for the "3h–Weekday" register it says:
"""
This register holds the current day of the week. Each value represents
one weekday that is assigned by the user. Values will range from 0 to 6
The weekday counter is simply a 3-bit counter which counts up to 6
and then resets to 0.
"""
So do not code weekday bitwise instead, use the raw values from
0-6.
Tested on "PHYTEC phyBOARD-Pollux i.MX8MP" board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210309134719.1494062-1-hs@denx.de
rtc_register_device() is a managed interface but it doesn't use devres
by itself - instead it marks an rtc_device as "registered" and the devres
callback for devm_rtc_allocate_device() takes care of resource release.
This doesn't correspond with the design behind devres where managed
structures should not be aware of being managed. The correct solution
here is to register a separate devres callback for unregistering the
device.
While at it: rename rtc_register_device() to devm_rtc_register_device()
and add it to the list of managed interfaces in devres.rst. This way we
can avoid any potential confusion of driver developers who may expect
there to exist a corresponding unregister function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201109163409.24301-8-brgl@bgdev.pl
rtc_nvmem_register() is a managed interface. It doesn't require any
release function to be called at driver detach. To avoid confusing
driver authors, let's rename it to devm_rtc_nvmem_register() and add it
to the list of managed interfaces in Documentation/.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201109163409.24301-6-brgl@bgdev.pl
If RV3028_CTRL1_EERD is not set (this is the default), the RTC will refresh
the RAM configuration registers from the EEPROM at midnight. It is
necessary to save the RAM registers back to EEPROM after modifying them.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201009153101.721149-4-alexandre.belloni@bootlin.com
rv3028_clkout_set_rate unconditionally sets RV3028_CLKOUT_CLKOE but
clk_set_rate may be called with the clock disabled. Ensure the clock is
kept disabled if it was not yet enabled.
Also, the actual rate was overwritten when enabling the clock, properly
write to the register only once.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201009153101.721149-1-alexandre.belloni@bootlin.com
rv3028_probe() misses a check for devm_regmap_init_i2c().
Add the missed check to fix it.
Fixes: e6e7376cfd ("rtc: rv3028: add new driver")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200528103950.912353-1-hslester96@gmail.com
Remove RTC_VL_CLR handling because it is a disservice to userspace as it
removes the important information that the RTC data is invalid. This may
lead userspace to set an invalid system time later on.
Link: https://lore.kernel.org/r/20191214220259.621996-13-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
rv3028 provides clkout (enabled by default). Add clkout
to clock framework source and control from device tree for
variable frequency with enable and disable functionality.
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Link: https://lore.kernel.org/r/20191018100425.1687979-1-pn@denx.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC core now has error messages in case of registration failure, there
is no need to have other messages in the drivers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20190818220041.17833-2-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add a driver for the MicroCrystal RV-3028. It is a SMT Real-Time Clock
Module that incorporates an integrated CMOS circuit together with an XTAL.
It has an i2c interface.
The driver handles date/time, alarms, trickle charging, timestamping,
frequency offset correction, EEPROM and NVRAM.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Alexandre Belloni