See the previous patch ("soc: rockchip: power-domain: Manage resource
conflicts with firmware") for a thorough explanation of the conflicts.
While ARM Trusted Firmware may be modifying memory controller and
power-domain states, we need to block the kernel's power-domain driver.
If the power-domain driver is disabled, there is no resource conflict
and this becomes a no-op.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This static struct can get reused if the device gets removed/reprobed,
and that causes use-after-free in its ->freq_table.
Let's just move the struct to our dynamic allocation.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We want to keep the idle time fixed, so compute based on the current DDR
frequency.
The old properties were deprecated and never used, so we can safely drop
them from the driver.
This is a rewritten version of work by Lin Huang <hl@rock-chips.com>.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Implement the newly-defined properties to allow disabling certain
power-saving-at-idle features at higher frequencies.
This is a rewritten version of work by Lin Huang <hl@rock-chips.com>.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
We're going to add new usages, and it's cleaner to work with macros
instead of comments and magic numbers.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
All of these properties are initialized by ARM Trusted Firmware, and
have been since the early days of this chip. It's redundant (and
possibly wrong) to do this here now. What's more, there seems to be some
confusion about the units and some of the definitions of this timing
struct: the DT docs say MHz for many of these, but downstream users were
in Hz (and therefore, the ATF interface was Hz). Also, the in-driver
usage for some of these (e.g., for comparing to target frequency) were
in Hz too. So doubly wrong.
We can avoid thinking about who got the right units by dropping the
unnecessary code and properties. They are marked deprecated in the
binding schema.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
These properties are:
* undocumented
* directly representing software properties, not hardware properties
* unused (no in-tree users, yet; this IP block has so far only been used
in downstream kernels)
Let's just stick the values that downstream users have been using
directly in the driver and call it a day.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Eliminate the following coccicheck warning:
./drivers/devfreq/rk3399_dmc.c:403:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Previously, devfreq core support 'devfreq-events' property in order to get
the devfreq-event device by phandle. But, 'devfreq-events' property name is
not proper on devicetree binding because this name doesn't mean
the any h/w attribute.
The devfreq-event core hand over the rights to decide the property name
for getting the devfreq-event device on devicetree. Each devfreq-event driver
will decide the property name on devicetree binding and then pass
the their own property name to devfreq_event_get_edev_by_phandle function.
And change the prototype of devfreq_event_get_edev_count function
because of used deprecated 'devfreq-events' property.
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Booting a recent kernel on a rk3399-based system (nanopc-t4),
equipped with a recent u-boot and ATF results in an Oops due
to a NULL pointer dereference.
This turns out to be due to the rk3399-dmc driver looking for
an *undocumented* property (rockchip,pmu), and happily using
a NULL pointer when the property isn't there.
Instead, make most of what was brought in with 9173c5ceb0
("PM / devfreq: rk3399_dmc: Pass ODT and auto power down parameters
to TF-A.") conditioned on finding this property in the device-tree,
preventing the driver from exploding.
Cc: stable@vger.kernel.org
Fixes: 9173c5ceb0 ("PM / devfreq: rk3399_dmc: Pass ODT and auto power down parameters to TF-A.")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The probe process may fail, but the devfreq event device remains
enabled. Call devfreq_event_disable_edev on the error return path.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
of_node_put() needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the
on-die termination (ODT) and auto power down parameters from kernel,
this patch adds the functionality to do this. Also, if DDR clock
frequency is lower than the on-die termination (ODT) disable frequency
this driver should disable the DDR ODT.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The semicolon is unneeded, so remove it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The opp table is not removed when the driver is unloaded neither when
there is an error within probe, so if the driver is reloaded the opp
core shows the following warning:
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
200000000, volt: 900000, enabled: 1. New: freq: 200000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
400000000, volt: 900000, enabled: 1. New: freq: 400000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
666000000, volt: 900000, enabled: 1. New: freq: 666000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
800000000, volt: 900000, enabled: 1. New: freq: 800000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
928000000, volt: 900000, enabled: 1. New: freq: 928000000,
volt: 900000, enabled: 1
This patch fixes the error path in the probe function and adds a .remove
function to properly cleanup the opp table on unloading.
Fixes: 5a893e31a6 (PM / devfreq: rockchip: add devfreq driver for rk3399 dmc)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Fix some spelling mistakes in error and debug messages.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
We just return -EPROBE_DEFER error code to caller and do not
print error message when try to get center logic regulator
and DMC clock defer.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
We have already wait dcf done in ATF, so don't need wait dcf irq
in kernel, besides, clear dcf irq in kernel will import competiton
between kernel and ATF, only handle dcf irq in ATF is a better way.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Prior to that, the devfreq device uses the governor name when adding
the itself. In order to prevent the mistake used the wrong governor name,
this patch defines the governor name as a constant and then uses them
instead of using the string directly.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
platform_get_irq() returns an error code, but the rk3399_dmc
driver ignores it and always returns -EINVAL. This is not correct,
and prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch updates dev_pm_opp_find_freq_*() routines to get a reference
to the OPPs returned by them.
Also updates the users of dev_pm_opp_find_freq_*() routines to call
dev_pm_opp_put() after they are done using the OPPs.
As it is guaranteed the that OPPs wouldn't get freed while being used,
the RCU read side locking present with the users isn't required anymore.
Drop it as well.
This patch also updates all users of devfreq_recommended_opp() which was
returning an OPP received from the OPP core.
Note that some of the OPP core routines have gained
rcu_read_{lock|unlock}() calls, as those still use RCU specific APIs
within them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> [Devfreq]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The OPP structures are abused to the best here, without understanding
how the OPP core and RCU locks work.
In short, the OPP pointer saved in 'rk3399_dmcfreq' can become invalid
under your nose, as the OPP core may free it.
Fix various abuses around OPP structures and calls.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This call never had the rcu_read_lock() counterpart. Remove the unlock
part as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch uses the resource-managed to add the devfreq device.
This function will make it easy to handle the devfreq device.
- struct devfreq *devm_devfreq_add_device(struct device *dev,
struct devfreq_dev_profile *profile,
const char *governor_name,
void *data);
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/devfreq/rk3399_dmc.ko | grep alias
$
After this patch:
$ modinfo drivers/devfreq/rk3399_dmc.ko | grep alias
alias: of:N*T*Crockchip,rk3399-dmcC*
alias: of:N*T*Crockchip,rk3399-dmc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Current code uses devm_regulator_get() in .probe so a regulator_put() will
be automatically called when unload the module. Remove the explictly
regulator_put() call and then we can also remove rk3399_dmcfreq_remove().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
base on dfi result, we do ddr frequency scaling, register
dmc driver to devfreq framework, and use simple-ondemand
policy.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: MyngJoo Ham <myngjoo.ham@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Brian Norris