There is a race condition in tpm_common_write function allowing
two threads on the same /dev/tpm<N>, or two different applications
on the same /dev/tpmrm<N> to overwrite each other commands/responses.
Fixed this by taking the priv->buffer_mutex early in the function.
Also converted the priv->data_pending from atomic to a regular size_t
type. There is no need for it to be atomic since it is only touched
under the protection of the priv->buffer_mutex.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The TPM burstcount and status commands are supposed to return very
quickly [2][3]. This patch further reduces the TPM poll sleep time to usecs
in get_burstcount() and wait_for_tpm_stat() by calling usleep_range()
directly.
After this change, performance on a system[1] with a TPM 1.2 with an 8 byte
burstcount for 1000 extends improved from ~10.7 sec to ~7 sec.
[1] All tests are performed on an x86 based, locked down, single purpose
closed system. It has Infineon TPM 1.2 using LPC Bus.
[2] From the TCG Specification "TCG PC Client Specific TPM Interface
Specification (TIS), Family 1.2":
"NOTE : It takes roughly 330 ns per byte transfer on LPC. 256 bytes would
take 84 us, which is a long time to stall the CPU. Chipsets may not be
designed to post this much data to LPC; therefore, the CPU itself is
stalled for much of this time. Sending 1 kB would take 350 μs. Therefore,
even if the TPM_STS_x.burstCount field is a high value, software SHOULD
be interruptible during this period."
[3] From the TCG Specification 2.0, "TCG PC Client Platform TPM Profile
(PTP) Specification":
"It takes roughly 330 ns per byte transfer on LPC. 256 bytes would take
84 us. Chipsets may not be designed to post this much data to LPC;
therefore, the CPU itself is stalled for much of this time. Sending 1 kB
would take 350 us. Therefore, even if the TPM_STS_x.burstCount field is a
high value, software should be interruptible during this period. For SPI,
assuming 20MHz clock and 64-byte transfers, it would take about 120 usec
to move 256B of data. Sending 1kB would take about 500 usec. If the
transactions are done using 4 bytes at a time, then it would take about
1 msec. to transfer 1kB of data."
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Jay Freyensee <why2jjj.linux@gmail.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Use kmemdup rather than duplicating its implementation.
Signed-off-by: Ji-Hun Kim <ji_hun.kim@samsung.com>
Reviewed-by: James Morris <james.morris@microsoft.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Use kmemdup rather than duplicating its implementation.
Signed-off-by: Ji-Hun Kim <ji_hun.kim@samsung.com>
Reviewed-by: James Morris <james.morris@microsoft.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
If load context command returns with TPM2_RC_HANDLE or TPM2_RC_REFERENCE_H0
then we have use after free in line 114 and double free in 117.
Fixes: 4d57856a21 ("tpm2: add session handle context saving and restoring to the space code")
Cc: stable@vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off--by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
tpm_try_transmit currently checks TPM status every 5 msecs between
send and recv. It does so in a loop for the maximum timeout as defined
in the TPM Interface Specification. However, the TPM may return before
5 msecs. Thus the polling interval for each iteration can be reduced,
which improves overall performance. This patch changes the polling sleep
time from 5 msecs to 1 msec.
Additionally, this patch renames TPM_POLL_SLEEP to TPM_TIMEOUT_POLL and
moves it to tpm.h as an enum value.
After this change, performance on a system[1] with a TPM 1.2 with an 8 byte
burstcount for 1000 extends improved from ~14 sec to ~10.7 sec.
[1] All tests are performed on an x86 based, locked down, single purpose
closed system. It has Infineon TPM 1.2 using LPC Bus.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Acked-by: Jay Freyensee <why2jjj.linux@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
For certain tpm chips releasing locality can take long enough that a
subsequent call to request_locality will see the locality as being active
when the access register is read in check_locality. So check that the
locality has been released before returning from release_locality.
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Reported-by: Laurent Bigonville <bigon@debian.org>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Laurent Bigonville <bigon@debian.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
In crb_map_io() function, __crb_request_locality() is called prior
to crb_cmd_ready(), but if one of the consecutive function fails
the flow bails out instead of trying to relinquish locality.
This patch adds goto jump to __crb_relinquish_locality() on the error path.
Fixes: 888d867df4 (tpm: cmd_ready command can be issued only after granting locality)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fix spelling mistake, rename ST33ZP24_TISREGISTER_UKNOWN to
ST33ZP24_TISREGISTER_UNKNOWN
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reduce the size of tpm.h by moving eventlog declarations to a separate
header.
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Functions and structures specific to TPM1 are renamed from tpm* to tpm1*.
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Currently chip is being dereferenced by the call to dev_get_drvdata
before it is being null checked, however, chip can never be null, so
this check is misleading and redundant. Remove it.
Detected by CoverityScan, CID#1357806 ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jarkko Sakkinen <jarkkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkkko.sakkinen@linux.intel.com>
Commit e2fb992d82 ("tpm: add retry logic") introduced a new loop to
handle the TPM2_RC_RETRY error. The loop retries the command after
sleeping for the specified time, which is incremented exponentially in
every iteration.
Unfortunately, the loop doubles the time before sleeping, causing the
initial sleep to be doubled. This patch fixes the initial sleep time.
Fixes: commit e2fb992d82 ("tpm: add retry logic")
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Pull TPM updates from James Morris:
"This release contains only bug fixes. There are no new major features
added"
* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: fix intermittent failure with self tests
tpm: add retry logic
tpm: self test failure should not cause suspend to fail
tpm2: add longer timeouts for creation commands.
tpm_crb: use __le64 annotated variable for response buffer address
tpm: fix buffer type in tpm_transmit_cmd
tpm: tpm-interface: fix tpm_transmit/_cmd kdoc
tpm: cmd_ready command can be issued only after granting locality
In the effort to remove all VLAs from the kernel[1], it is desirable to
build with -Wvla. However, this warning is overly pessimistic, in that
it is only happy with stack array sizes that are declared as constant
expressions, and not constant values. One case of this is the
evaluation of the max() macro which, due to its construction, ends up
converting constant expression arguments into a constant value result.
All attempts to rewrite this macro with __builtin_constant_p() failed
with older compilers (e.g. gcc 4.4)[2]. However, Martin Uecker,
constructed[3] a mind-shattering solution that works everywhere.
Cthulhu fhtagn!
This patch updates the min()/max() macros to evaluate to a constant
expression when called on constant expression arguments. This removes
several false-positive stack VLA warnings from an x86 allmodconfig build
when -Wvla is added:
$ diff -u before.txt after.txt | grep ^-
-drivers/input/touchscreen/cyttsp4_core.c:871:2: warning: ISO C90 forbids variable length array ‘ids’ [-Wvla]
-fs/btrfs/tree-checker.c:344:4: warning: ISO C90 forbids variable length array ‘namebuf’ [-Wvla]
-lib/vsprintf.c:747:2: warning: ISO C90 forbids variable length array ‘sym’ [-Wvla]
-net/ipv4/proc.c:403:2: warning: ISO C90 forbids variable length array ‘buff’ [-Wvla]
-net/ipv6/proc.c:198:2: warning: ISO C90 forbids variable length array ‘buff’ [-Wvla]
-net/ipv6/proc.c:218:2: warning: ISO C90 forbids variable length array ‘buff64’ [-Wvla]
This also updates two cases where different enums were being compared
and explicitly casts them to int (which matches the old side-effect of
the single-evaluation code): one in tpm/tpm_tis_core.h, and one in
drm/drm_color_mgmt.c.
[1] https://lkml.org/lkml/2018/3/7/621
[2] https://lkml.org/lkml/2018/3/10/170
[3] https://lkml.org/lkml/2018/3/20/845
Co-Developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Co-Developed-by: Martin Uecker <Martin.Uecker@med.uni-goettingen.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
My Nuvoton 6xx in a Dell XPS-13 has been intermittently failing to work
(necessitating a reboot). The problem seems to be that the TPM gets into a
state where the partial self-test doesn't return TPM_RC_SUCCESS (meaning
all tests have run to completion), but instead returns TPM_RC_TESTING
(meaning some tests are still running in the background). There are
various theories that resending the self-test command actually causes the
tests to restart and thus triggers more TPM_RC_TESTING returns until the
timeout is exceeded.
There are several issues here: firstly being we shouldn't slow down the
boot sequence waiting for the self test to complete once the TPM
backgrounds them. It will actually make available all functions that have
passed and if it gets a failure return TPM_RC_FAILURE to every subsequent
command. So the fix is to kick off self tests once and if they return
TPM_RC_TESTING log that as a backgrounded self test and continue on. In
order to prevent other tpm users from seeing any TPM_RC_TESTING returns
(which it might if they send a command that needs a TPM subsystem which is
still under test), we loop in tpm_transmit_cmd until either a timeout or we
don't get a TPM_RC_TESTING return.
Finally, there have been observations of strange returns from a partial
test. One Nuvoton is occasionally returning TPM_RC_COMMAND_CODE, so treat
any unexpected return from a partial self test as an indication we need to
run a full self test.
[jarkko.sakkinen@linux.intel.com: cleaned up some klog messages and
dropped tpm_transmit_check() helper function from James' original
commit.]
Fixes: 2482b1bba5 ("tpm: Trigger only missing TPM 2.0 self tests")
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
TPM2 can return TPM2_RC_RETRY to any command and when it does we get
unexpected failures inside the kernel that surprise users (this is
mostly observed in the trusted key handling code). The UEFI 2.6 spec
has advice on how to handle this:
The firmware SHALL not return TPM2_RC_RETRY prior to the completion
of the call to ExitBootServices().
Implementer’s Note: the implementation of this function should check
the return value in the TPM response and, if it is TPM2_RC_RETRY,
resend the command. The implementation may abort if a sufficient
number of retries has been done.
So we follow that advice in our tpm_transmit() code using
TPM2_DURATION_SHORT as the initial wait duration and
TPM2_DURATION_LONG as the maximum wait time. This should fix all the
in-kernel use cases and also means that user space TSS implementations
don't have to have their own retry handling.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The Acer Acer Veriton X4110G has a TPM device detected as:
tpm_tis 00:0b: 1.2 TPM (device-id 0xFE, rev-id 71)
After the first S3 suspend, the following error appears during resume:
tpm tpm0: A TPM error(38) occurred continue selftest
Any following S3 suspend attempts will now fail with this error:
tpm tpm0: Error (38) sending savestate before suspend
PM: Device 00:0b failed to suspend: error 38
Error 38 is TPM_ERR_INVALID_POSTINIT which means the TPM is
not in the correct state. This indicates that the platform BIOS
is not sending the usual TPM_Startup command during S3 resume.
>From this point onwards, all TPM commands will fail.
The same issue was previously reported on Foxconn 6150BK8MC and
Sony Vaio TX3.
The platform behaviour seems broken here, but we should not break
suspend/resume because of this.
When the unexpected TPM state is encountered, set a flag to skip the
affected TPM_SaveState command on later suspends.
Cc: stable@vger.kernel.org
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Link: http://lkml.kernel.org/r/CAB4CAwfSCvj1cudi+MWaB5g2Z67d9DwY1o475YOZD64ma23UiQ@mail.gmail.com
Link: https://lkml.org/lkml/2011/3/28/192
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=591031
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
TPM2_CC_Create(0x153) and TPM2_CC_CreatePrimary (0x131) involve generation
of crypto keys which can be a computationally intensive task. The timeout
is set to 3min. Rather than increasing default timeout a new constant is
added, to not stall for too long on regular commands failures.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
use __le64 annotated variable for response buffer address as this is
read in little endian format form the register.
This suppresses sparse warning
drivers/char/tpm/tpm_crb.c:558:18: warning: cast to restricted __le64
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
1. The buffer cannot be const as it is used both for send and receive.
2. Drop useless casting to u8 *, as this is already a
type of 'buf' parameter, it has just masked the 'const' issue.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fix tmp_ -> tpm_ typo and add reference to 'space' parameter
in kdoc for tpm_transmit and tpm_transmit_cmd functions.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The correct sequence is to first request locality and only after
that perform cmd_ready handshake, otherwise the hardware will drop
the subsequent message as from the device point of view the cmd_ready
handshake wasn't performed. Symmetrically locality has to be relinquished
only after going idle handshake has completed, this requires that
go_idle has to poll for the completion and as well locality
relinquish has to poll for completion so it is not overridden
in back to back commands flow.
Two wrapper functions are added (request_locality relinquish_locality)
to simplify the error handling.
The issue is only visible on devices that support multiple localities.
Fixes: 877c57d0d0 ("tpm_crb: request and relinquish locality 0")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. If a bit does
flip it could cause an overrun if it's in one of the size parameters,
so sanity check that we're not overrunning the provided buffer when
doing a memcpy().
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull tpm updates from James Morris:
- reduce polling delays in tpm_tis
- support retrieving TPM 2.0 Event Log through EFI before
ExitBootServices
- replace tpm-rng.c with a hwrng device managed by the driver for each
TPM device
- TPM resource manager synthesizes TPM_RC_COMMAND_CODE response instead
of returning -EINVAL for unknown TPM commands. This makes user space
more sound.
- CLKRUN fixes:
* Keep #CLKRUN disable through the entier TPM command/response flow
* Check whether #CLKRUN is enabled before disabling and enabling it
again because enabling it breaks PS/2 devices on a system where it
is disabled
* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: remove unused variables
tpm: remove unused data fields from I2C and OF device ID tables
tpm: only attempt to disable the LPC CLKRUN if is already enabled
tpm: follow coding style for variable declaration in tpm_tis_core_init()
tpm: delete the TPM_TIS_CLK_ENABLE flag
tpm: Update MAINTAINERS for Jason Gunthorpe
tpm: Keep CLKRUN enabled throughout the duration of transmit_cmd()
tpm_tis: Move ilb_base_addr to tpm_tis_data
tpm2-cmd: allow more attempts for selftest execution
tpm: return a TPM_RC_COMMAND_CODE response if command is not implemented
tpm: Move Linux RNG connection to hwrng
tpm: use struct tpm_chip for tpm_chip_find_get()
tpm: parse TPM event logs based on EFI table
efi: call get_event_log before ExitBootServices
tpm: add event log format version
tpm: rename event log provider files
tpm: move tpm_eventlog.h outside of drivers folder
tpm: use tpm_msleep() value as max delay
tpm: reduce tpm polling delay in tpm_tis_core
tpm: move wait_for_tpm_stat() to respective driver files
The CLKRUN fix caused a few harmless compile-time warnings:
drivers/char/tpm/tpm_tis.c: In function 'tpm_tis_pnp_remove':
drivers/char/tpm/tpm_tis.c:274:23: error: unused variable 'priv' [-Werror=unused-variable]
drivers/char/tpm/tpm_tis.c: In function 'tpm_tis_plat_remove':
drivers/char/tpm/tpm_tis.c:324:23: error: unused variable 'priv' [-Werror=unused-variable]
This removes the variables that have now become unused.
Fixes: 6d0866cbc2d3 ("tpm: Keep CLKRUN enabled throughout the duration of transmit_cmd()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: James Morris <jmorris@namei.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The data field for the entries in the device tables are set but not used.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jason Gunthorpe <jgg@ziepe.ca>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Commit 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell systems")
added logic in the TPM TIS driver to disable the Low Pin Count CLKRUN
signal during TPM transactions.
Unfortunately this breaks other devices that are attached to the LPC bus
like for example PS/2 mouse and keyboards.
One flaw with the logic is that it assumes that the CLKRUN is always
enabled, and so it unconditionally enables it after a TPM transaction.
But it could be that the CLKRUN# signal was already disabled in the LPC
bus and so after the driver probes, CLKRUN_EN will remain enabled which
may break other devices that are attached to the LPC bus but don't have
support for the CLKRUN protocol.
Fixes: 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell systems")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: James Ettle <james@ettle.org.uk>
Tested-by: Jeffery Miller <jmiller@neverware.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The coding style says "use just one data declaration per line (no commas
for multiple data declarations)" so follow this convention.
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This flag is only used to warn if CLKRUN_EN wasn't disabled on Braswell
systems, but the only way this can happen is if the code is not correct.
So it's an unnecessary check that just makes the code harder to read.
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Commit 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell
systems") disabled CLKRUN protocol during TPM transactions and re-enabled
once the transaction is completed. But there were still some corner cases
observed where, reading of TPM header failed for savestate command
while going to suspend, which resulted in suspend failure.
To fix this issue keep the CLKRUN protocol disabled for the entire
duration of a single TPM command and not disabling and re-enabling
again for every TPM transaction. For the other TPM accesses outside
TPM command flow, add a higher level of disabling and re-enabling
the CLKRUN protocol, instead of doing for every TPM transaction.
Fixes: 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell systems")
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Previously, if the last attempt to execute the selftest command failed with
RC_TESTING, there was still a call to tpm_msleep, even though no further
attempt would be made. This causes an unnecessary delay, therefore ensure
that if the last attempt fails the function is left immediately.
Also, instead of ensuring that the cumulated runtime of all attempts is
larger than the command duration for TPM2_SelfTest, ensure that there is at
least one attempt for which the delay is larger than the expected command
duration. This allows slow TPMs to execute all their tests in the
background, without slowing down faster TPMs that have finished their tests
earlier. If tests are still not finished even with this long delay, then
something is broken and the TPM is not used.
Fixes: 125a221054 ("tpm: React correctly to RC_TESTING from TPM 2.0 self
tests")
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
According to the TPM Library Specification, a TPM device must do a command
header validation before processing and return a TPM_RC_COMMAND_CODE code
if the command is not implemented.
So user-space will expect to handle that response as an error. But if the
in-kernel resource manager is used (/dev/tpmrm?), an -EINVAL errno code is
returned instead if the command isn't implemented. This confuses userspace
since it doesn't expect that error value.
This also isn't consistent with the behavior when not using TPM spaces and
accessing the TPM directly (/dev/tpm?). In this case, the command is sent
to the TPM even when not implemented and the TPM responds with an error.
Instead of returning an -EINVAL errno code when the tpm_validate_command()
function fails, synthesize a TPM command response so user-space can get a
TPM_RC_COMMAND_CODE as expected when a chip doesn't implement the command.
The TPM only sets 12 of the 32 bits in the TPM_RC response, so the TSS and
TAB specifications define that higher layers in the stack should use some
of the unused 20 bits to specify from which level of the stack the error
is coming from.
Since the TPM_RC_COMMAND_CODE response code is sent by the kernel resource
manager, set the error level to the TAB/RM layer so user-space is aware of
this.
Suggested-by: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: William Roberts <william.c.roberts@intel.com>
Reviewed-by: Philip Tricca <philip.b.tricca@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The tpm-rng.c approach is completely inconsistent with how the kernel
handles hotplug. Instead manage a hwrng device for each TPM. This will
cause the kernel to read entropy from the TPM when it is plugged in, and
allow access to the TPM rng via /dev/hwrng.
Signed-off-by: Jason Gunthorpe <jgg@ziepe.ca>
Tested-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Device number (the character device index) is not a stable identifier
for a TPM chip. That is the reason why every call site passes
TPM_ANY_NUM to tpm_chip_find_get().
This commit changes the API in a way that instead a struct tpm_chip
instance is given and NULL means the default chip. In addition, this
commit refines the documentation to be up to date with the
implementation.
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> (@chip_num -> @chip part)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgg@ziepe.ca>
Tested-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
If we are not able to retrieve the TPM event logs from the ACPI table,
check the EFI configuration table (Linux-specific GUID).
The format version of the log is now returned by the provider function.
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Rename the current TPM Event Log provider files (ACPI and OF)
for clarity.
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The generic definitions of data structures in tpm_eventlog.h are
required by other part of the kernel (namely, the EFI stub).
Signed-off-by: Thiebaud Weksteen <tweek@google.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Currently, tpm_msleep() uses delay_msec as the minimum value in
usleep_range. However, that is the maximum time we want to wait.
The function is modified to use the delay_msec as the maximum
value, not the minimum value.
After this change, performance on a TPM 1.2 with an 8 byte
burstcount for 1000 extends improved from ~9sec to ~8sec.
Fixes: 3b9af007869("tpm: replace msleep() with usleep_range() in TPM 1.2/
2.0 generic drivers")
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The existing wait_for_tpm_stat() polls for the chip status after
5msec sleep. As per TCG ddwg input, it is expected that tpm might
return status in few usec. So, reducing the delay in polling to
1msec.
Similarly, get_burstcount() function sleeps for 5msec before
retrying for next query to burstcount in a loop. If it takes
lesser time for TPM to return, this 5msec delay is longer than
necessary.
After this change, performance on a TPM 1.2 with an 8 byte
burstcount for 1000 extends improved from ~14sec to ~9sec.
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The function wait_for_tpm_stat() is currently defined in
tpm-interface file. It is a hardware specific function used
only by tpm_tis and xen-tpmfront, so it is removed from
tpm-interface.c and defined in respective driver files.
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Kees Cook