The code is dead at least since 2002. So remove it to not distort git
grep output (about port.tty usage).
Remove the whole do_softirq tasklet as it's noop now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Errata E20: UART: Character Timeout interrupt remains set under certain
software conditions.
Implication: The software servicing the UART can be trapped in an infinite loop.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Synopsys DesignWare 8250 is an 8250 that has an extra interrupt that
gets raised when writing to the LCR when busy. To handle this we need
special serial_out, serial_in and handle_irq methods. Add a new
platform driver that uses these accessors.
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow modules to use the normal 8250 irq handler inside their own.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ePAPR hypervisor byte channel driver is supposed to work on all
ePAPR-compliant embedded PowerPC systems, but it had a reference to the MSR_GS
bit, which is available only on Book-E systems.
Also fix a couple integer-to-pointer typecast problems.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We want to keep refcounts properly on this against hangup.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves several occurences of similar code inside receive_chars(),
which now also takes care of checking for break and calling sysrq handling
code.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The main thread is waiting on on a wait_queue but wake_up_process() is
used to wake the thread. This reads weirdly. Change wake_up_process() to
wake_up().
Tested on the Moorestown tablet build
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A DISC on DLCI 0 should close down the mux but Michael Lauer reports this
is not the case for some modems. Send a CLD as well.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Michael Lauer
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doesn't appear to be much to do here, however having the suspend/resume
functions will allow the d3/d0 transitions to be sent by the pci core.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let's use the newly added helper to avoid stalls in drivers which are
not yet ported to tty_port helpers.
Those which are broken (call tty_wait_until_sent with irqs disabled)
are left untouched. They are in a deeper trouble than we are trying to
solve here. This includes amiserial, 68328serial, 68360serial and
crisv10.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let's use the newly added helper to avoid stalls in drivers which are
already ported to tty_port helpers.
We have to ensure here, that there is no user of tty_port_close_start
and tty_port_close which holds port->mutex (or other) lock over them.
And sure, there is none.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So now, when we handle CLOSING flag, there is no point to hold
port->mutex over the start of uart_close.
Yes, there are still several things to reason about:
* port->count etc is and always was protected by a spinlock
* ->stop_rx is protected by a spinlock. Otherwise it would
race with interrupts.
* uart_wait_until_sent -- that one is already called without
port->mutex from set_termios and tty_set_ldisc. Should anything
be protected there, it would be tx_empty. And by a spinlock.
8250 does this internally...
This step is needed to fix system stalls. To not create an AB-BA lock
dependency (see next patches).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to move port->mutex locking after wait_until_sent in
uart_close (for rationale see next patches). But if we did it now, we
would introduce a race between close and open. This is exactly why
port->mutex is locked at the top of uart_close.
To avoid the race, we add ASYNCB_CLOSING to uart_close. Like every
other sane TTY driver. Thanks to tty_port_block_til_ready used in
uart_open we will have this for free. Then we can move the port->mutex
lock.
Also note that this will make the conversion to tty_port helpers
easier. They are currently handling ASYNC_CLOSING flag correctly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of printing the head of the buffer, we should print the tail,
which is the byte we are sending to the device.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
jsm uses a write queue that copies from uart_core circular buffer. This
copying however has some bugs, like not wrapping the head counter. Since
this write queue is also a circular buffer, the consumer function is
ready to use the uart_core circular buffer directly.
This buggy copying function was making some bytes be dropped when
transmitting to a raw tty, doing something like this.
[root@hostname ~]$ cat /dev/ttyn1 > cascardo/dump &
[1] 2658
[root@hostname ~]$ cat /proc/tty/drivers > /dev/ttyn0
[root@hostname ~]$ cat /proc/tty/drivers
/dev/tty /dev/tty 5 0 system:/dev/tty
/dev/console /dev/console 5 1 system:console
/dev/ptmx /dev/ptmx 5 2 system
/dev/vc/0 /dev/vc/0 4 0 system:vtmaster
jsm /dev/ttyn 250 0-31 serial
serial /dev/ttyS 4 64-95 serial
hvc /dev/hvc 229 0-7 system
pty_slave /dev/pts 136 0-1048575 pty:slave
pty_master /dev/ptm 128 0-1048575 pty:master
unknown /dev/tty 4 1-63 console
[root@hostname ~]$ cat cascardo/dump
/dev/tty /dev/tty 5 0 system:/dev/tty
/dev/console /dev/console 5 1 system:console
/dev/ptmx /dev/ptmx 5 2 system
/dev/vc/0 /dev/vc/0 4 0 system:vtmaste[root@hostname ~]$
This patch drops the driver write queue entirely, using the circular
buffer from uart_core only.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The flip buffer is not used anymore. Remove its allocation and
declaration in the board structure.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to add support EXYNOS4212 SoC, we need to enable
SERIAL_S5PV210 on EXYNOS4212.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
By default the atmel_serial driver in RS485 mode disables receiving data until
all data in the send buffer has been sent. This flag allows to receive data
even whilst sending data.
Signed-off-by: Bernhard Roth <br@pwrnet.de>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The imx UART hardware controller can identify BREAK character and the
imx_set_termios() can accept BRKINT set by users, but current existing
imx_rxint() can't pass BREAK character and TTY_BREAK to the tty layer
as other serial drivers do (8250.c omap_serial.c).
Here add code to handle BREAK character and pass it to tty layer.
To detect error occurrence, i use URXD_ERR to replace (URXD_OVRRUN |
URXD_FRMERR | ...) because any kind of error occurs, URXD_ERR will
always be set to 1.
I put the URXD_BRK to the first place to check since when BREAK error
occurs, not only URXD_BRK is set to 1, but also URXD_PRERR and
URXD_FRMERR are all set to 1. This arrangement can filter out fake
parity and frame errors when BREAK error occurs.
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 6b1a98d1c4.
It causes a build error that needs to be resolved differently.
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 14a8d47d4e.
It causes a build error that needs to be resolved differently.
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support the DesignWare 8250 by a new compatible string and registering
the DesignWare helpers. If the registration of the helpers fails, then
continue as a normal 8250 as we may still get some useful debug out.
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Synopsys DesignWare 8250 is an 8250 that has an extra interrupt that
gets raised when writing to the LCR when busy. To handle this we need
special serial_out, serial_in and handle_irq methods. Add a new
function serial8250_use_designware_io() that configures a uart_port with
these accessors.
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that platforms can override the port IRQ handler and the only user
of these UPIO modes has been converted over, kill off UPIO_DWAPB and
UPIO_DWAPB32.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some ports (e.g. Synopsys DesignWare 8250) have special requirements for
handling the interrupts. Allow these platforms to specify their own
interrupt handler that will override the default.
serial8250_handle_irq() is provided so that platforms can extend the IRQ
handler rather than completely replacing it.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
s3c64xx and later SoC's include the interrupt mask and pending registers
in the uart controller, unlike the s3c24xx SoC's which have these registers
in the interrupt controller. When the mask and pending registers are part
of the uart controller, a unified interrupt handler can handle the tx/rx
interrupt. With this, the static reservation of interrupt numbers for the
uart tx/rx/err interrupts in the linux irq space is not required and
simplifies adding device tree support.
Suggested-by: Grant Likely <grant.likely@secretlab.ca>
CC: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Serial TX IRQ is not RX IRQ plus 1 in some blackfin chips.
Give individual platform resources to both TX and RX irqs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Even though this is valid C we should not mix C99 initializers with
obfuscated ANSI C. Stick to C99 and initialize c by its name.
Found by clang:
drivers/tty/vt/vt.c:262:55: warning: explicitly assigning a variable of
type 'unsigned int' to itself [-Wself-assign]
struct vt_notifier_param param = { .vc = vc, unicode = unicode };
~~~~~~~ ^ ~~~~~~~
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
bfin_5xx.c is not a general name for all Blackfin chips.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It makes the code really ugly. And since it can be enabled only before
building and only in the source files, it can be barely used by users.
That said, I've not seen anybody to use it in the past few years.
This crap is copied to some more drivers over the tty tree. Since I'm
not their maintainer, I'm not sure if I should remove them too?
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We used it really only serial and ami_serial. The rest of the
callsites were BUG/WARN_ONs to check if BTM is held. Now that we
pruned tty_locked from both of the real users, we can get rid of
tty_lock along with __big_tty_mutex_owner.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The same as in "TTY: serial, remove BTM from wait_until_sent" we don't
need to take BTM in wait_until_sent of ami_serial. Exactly the same
as serial, ami_serial accesses some "info" members (xmit_fifo_size,
timeout), but their assignment on other places in the code is not
protected by BTM anyway.
So the BTM protects nothing here. This removal helps us to get rid of
tty_locked() and __big_tty_mutex_owner in the following patch. This
was suggested by Arnd.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Andreas Bombe <aeb@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tty_wakeup can be called from any context. So there is no need to have
an extra tasklet for calling that. Hence save some space and remove
the tasklet completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It doesn't make sense to set console to uart_port in console->setup.
At that time the console is set by uart_add_one_port already.
The call chain looked like:
uart_add_one_port()
uport->cons = drv->cons; <= once
uart_configure_port()
register_console()
console->setup()
port->cons = co; <= second time
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During the BKL removal process, the BKL was switched to tty_lock
(BTM). Now we should start pruning the BTM further. Let's start with
wait_until_sent of the serial layer. This will allow us to switch to
the tty port helpers and thus clean it up much.
In wait_until_sent there are some uport members accessed, but neither
of them is protected by BTM at the location they are set ('=>' means
function call):
* uport->fifosize (set in tty_ioctl => uart_ioctl => uart_set_info)
* uport->type (set in add_one_port prior to tty_register_device)
* uport->timeout (set usually in tty_ioctl => tty_mode_ioctl =>
tty_set_termios => uart_set_termios => uart_change_speed =>
uport->ops->set_termios => uart_update_timeout)
* call to uport->ops->tx_empty()
If the tx_empty hook needs some lock to protect accesses to registers,
it should take &uport->lock spinlock like 8250 does. Otherwise there
still might be races e.g. with ISRs.
This should also fix the issue Andreas is seeing (BTM in comparison to
BKL doesn't have any hidden functionality like unlocking during
sleeping).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
References: https://lkml.org/lkml/2011/5/25/562
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andreas Bombe <aeb@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ePAPR embedded hypervisor specification provides an API for "byte
channels", which are serial-like virtual devices for sending and receiving
streams of bytes. This driver provides Linux kernel support for byte
channels via three distinct interfaces:
1) An early-console (udbg) driver. This provides early console output
through a byte channel. The byte channel handle must be specified in a
Kconfig option.
2) A normal console driver. Output is sent to the byte channel designated
for stdout in the device tree. The console driver is for handling kernel
printk calls.
3) A tty driver, which is used to handle user-space input and output. The
byte channel used for the console is designated as the default tty.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix new kernel-doc warning in pci.c:
Warning(drivers/pci/pci.c:3259): No description found for parameter 'mps'
Warning(drivers/pci/pci.c:3259): Excess function parameter 'rq' description in 'pcie_set_mps'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge
Prior to Ivybridge, the GFX_MODE would default to 0x800, meaning that
MI_FLUSH would flush the TLBs in addition to the rest of the caches
indicated in the MI_FLUSH command. However starting with Ivybridge, the
register defaults to 0x2800 out of reset, meaning that to invalidate the
TLB we need to use PIPE_CONTROL. Since we're not doing that yet, go
back to the old default so things work.
v2: don't forget to actually *clear* the new bit
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.dk/linux-block: (23 commits)
Revert "cfq: Remove special treatment for metadata rqs."
block: fix flush machinery for stacking drivers with differring flush flags
block: improve rq_affinity placement
blktrace: add FLUSH/FUA support
Move some REQ flags to the common bio/request area
allow blk_flush_policy to return REQ_FSEQ_DATA independent of *FLUSH
xen/blkback: Make description more obvious.
cfq-iosched: Add documentation about idling
block: Make rq_affinity = 1 work as expected
block: swim3: fix unterminated of_device_id table
block/genhd.c: remove useless cast in diskstats_show()
drivers/cdrom/cdrom.c: relax check on dvd manufacturer value
drivers/block/drbd/drbd_nl.c: use bitmap_parse instead of __bitmap_parse
bsg-lib: add module.h include
cfq-iosched: Reduce linked group count upon group destruction
blk-throttle: correctly determine sync bio
loop: fix deadlock when sysfs and LOOP_CLR_FD race against each other
loop: add BLK_DEV_LOOP_MIN_COUNT=%i to allow distros 0 pre-allocated loop devices
loop: add management interface for on-demand device allocation
loop: replace linked list of allocated devices with an idr index
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: OF: Don't crash when bridge parent is NULL.
PCI: export pcie_bus_configure_settings symbol
PCI: code and comments cleanup
PCI: make cardbus-bridge resources optional
PCI: make SRIOV resources optional
PCI : ability to relocate assigned pci-resources
PCI: honor child buses add_size in hot plug configuration
PCI: Set PCI-E Max Payload Size on fabric
In pcibios_get_phb_of_node(), we will crash while booting if
bus->bridge->parent is NULL.
Check for this case and avoid dereferencing the NULL pointer.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, error handling code in this function calls the function
sata_dwc_port_stop, but this function has essentially no effect if hsdevp
has not been stored in ap, which is the case throughout this function. The
only effect is to print a debugging message including ap->print_id.
The code is rewritten to not call sata_dwc_port_stop, but instead to jump
to a local label that prints the original error message and the print_id
information. In the case where hsdevp has been already allocated (but not
yet stored in ap), this value is freed as well.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jiri Slaby