Can't link I2C and SPI to the same binary, better
to move CS35L41 to 3 modules approach.
And instead of exposing cs35l41_reg, volatile_reg,
readable_reg and precious_reg arrays, move
cs35l41_regmap_i2c/spi to new module and expose it.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211125143501.7720-1-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Higher speeds are only supported when PLL is enabled, but
the current driver doesn't enable PLL outside of stream
use cases, so better to set the lowest SPI speed accepted
by the entire device.
Move the current frequency set to the spi sub-driver so
the whole device can benefit from that speed.
spi-max-frequency property could be used, but ACPI systems don't
support it, so by setting it in the spi sub-driver probe
both Device Trees and ACPI systems are supported.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211123163149.1530535-2-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the internal monitor sources are input widgets, which means
if the card is set to fully routed these will not enable unless connected
to something in the machine driver. However, all these are internal
monitor signals so it makes no sense to connect them to something in the
machine driver. As such switch them to siggen widgets which will have
the same behaviour except not require external linkage on a fully routed
card.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: David Rhodes <drhodes@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211029214028.401284-1-drhodes@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Up to now cs35l41_remove() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c, platform and spi remove callbacks is
ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211020132416.30288-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not idiomatic for ASoC to print the function name in the error
messages, however it is expected to show the return code. Update the
error messages to follow these conventions.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210914141349.30218-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In multiple places the driver overwrites the error code returned with
a static error code, this is not helpful for debugging. Update to pass
the error codes straight through.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210914141349.30218-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cs35l41 is often connected over I2C which is a very slow bus, as such
timings can be greatly improved combining writes where acceptable.
Update several points where the driver does multiple register writes
when a single one would suffice.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210914141349.30218-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The loop checking PDN_DONE doesn't check the return value from
regmap_read, nor does it initialise val. This means if regmap_read fails
val will be checked for the PDN_DONE bit whilst being uninitialised.
Fix this up by switching to regmap_read_poll_timeout which tidies up the
code and avoids the uninitialised variable.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210914141349.30218-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown