and prepare and enable them at the same time. This also comes with devm support
so that drivers can make a single call to get and prepare and enable the clk
and have that all undone when their driver is removed. Many folks have
requested this feature over the years, but we've had disagreements about how to
implement it and if it was worthwhile to encourage drivers to use such an API.
Now it's here, so let's see how it goes. I hope that by introducing this API we
can identify drivers that would benefit from further consolidation of clk API
usage, possibly by moving such logic to the bus layer and out of drivers
altogether.
Outside of that major API update, we have the usual collection of driver
updates. A few new SoCs are supported, mostly Qualcomm and Renesas this time
around. Then we have the long tail of non-critical fixes and minor feature
additions to various clk drivers. And finally more clk provider migration to
struct clk_parent_data, reducing boot times in the process.
Core:
- devm helpers for clk_get() + clk_prepare() and clk_enable()
New Drivers:
- Support for the camera clock controller in Qualcomm SM8450 and
the display and gpu clock controllers in Qualcomm SM8350
- Add support for the Renesas RZ/Five SoC
Updates:
- Various fixes, new clocks and USB GDSCs are introduced for Qualcomm IPQ8074
- Fixes to Qualcomm MSM8939 for issues introduced by inheriting the MSM8916
GCC driver
- Support for a new type of voteable GDSCs used by Qualcomm SC8280XP PCIe
GDSCs
- Qualcomm SC8280XP pipe clocks transitioned to the new phy-mux implementation
- Qualcomm MSM8996 GCC, RPM clock driver and some clocks in MSM8994 GCC are
migrated to use clk_parent_data
- Corrected the topology for Titan (camera) GDSCs on Qualcomm SDM845 and
SM8250
- Qualcomm MSM8916 gains more possible frequencies for its GP clocks.
- The GCC and tsens handling on Qualcomm MSM8960 is reworked to mimic the
design in IPQ8074 to allow the GCC driver to probe earlier.
- The regulator based mmcx supply for Qualcomm dispcc and videocc is dropped,
as the only upstream target that adapted this interface was transitioned
several kernel versions ago
- Qualcomm GDSCs found to be enabled at boot will now reflect in the enable
count of the supply, as was done with the regulator supplies previously
- Correct adc1, nic_media and edma1's parents for NXP i.MX93
- rdiv, mfd values, the return rate in recalc_rate and add more frequencies in
the table for fracn-gppll on i.MX
- Remove Allwinner workaround logic/compatible in fixed factor code
- MediaTek clk driver cleanups
- Add reset support to more MediaTek clk drivers
- deduplicate Allwinner ccu_clks arrays
- Allwinner H6 GPU DFS support
- Adjust Allwinner Kconfig to limit choice
- Fix initconst confusion on Renesas R-Car Gen4
- Add GPT/POEG (PWM) clocks and resets on Renesas RZ/G2L
- Add PFC and WDT clocks and resets on Renesas RZ/V2M
- Add thermal, SDHI, Z (CPU core), PCIe, and HSCIF (serial) clocks on
Renesas R-Car S4-8
-----BEGIN PGP SIGNATURE-----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=jUh+
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk core gains a new set of APIs that allow drivers to both
acquire clks and prepare and enable them at the same time. This also
comes with devm support so that drivers can make a single call to get
and prepare and enable the clk and have that all undone when their
driver is removed.
Many folks have requested this feature over the years, but we've had
disagreements about how to implement it and if it was worthwhile to
encourage drivers to use such an API.
Now it's here, so let's see how it goes.
I hope that by introducing this API we can identify drivers that would
benefit from further consolidation of clk API usage, possibly by
moving such logic to the bus layer and out of drivers altogether.
Outside of that major API update, we have the usual collection of
driver updates. A few new SoCs are supported, mostly Qualcomm and
Renesas this time around. Then we have the long tail of non-critical
fixes and minor feature additions to various clk drivers.
And finally more clk provider migration to struct clk_parent_data,
reducing boot times in the process.
Summary:
Core:
- devm helpers for clk_get() + clk_prepare() and clk_enable()
New Drivers:
- Support for the camera clock controller in Qualcomm SM8450 and the
display and gpu clock controllers in Qualcomm SM8350
- Add support for the Renesas RZ/Five SoC
Updates:
- Various fixes, new clocks and USB GDSCs are introduced for Qualcomm
IPQ8074
- Fixes to Qualcomm MSM8939 for issues introduced by inheriting the
MSM8916 GCC driver
- Support for a new type of voteable GDSCs used by Qualcomm SC8280XP
PCIe GDSCs
- Qualcomm SC8280XP pipe clocks transitioned to the new phy-mux
implementation
- Qualcomm MSM8996 GCC, RPM clock driver and some clocks in MSM8994
GCC are migrated to use clk_parent_data
- Corrected the topology for Titan (camera) GDSCs on Qualcomm SDM845
and SM8250
- Qualcomm MSM8916 gains more possible frequencies for its GP clocks.
- The GCC and tsens handling on Qualcomm MSM8960 is reworked to mimic
the design in IPQ8074 to allow the GCC driver to probe earlier.
- The regulator based mmcx supply for Qualcomm dispcc and videocc is
dropped, as the only upstream target that adapted this interface
was transitioned several kernel versions ago
- Qualcomm GDSCs found to be enabled at boot will now reflect in the
enable count of the supply, as was done with the regulator supplies
previously
- Correct adc1, nic_media and edma1's parents for NXP i.MX93
- rdiv, mfd values, the return rate in recalc_rate and add more
frequencies in the table for fracn-gppll on i.MX
- Remove Allwinner workaround logic/compatible in fixed factor code
- MediaTek clk driver cleanups
- Add reset support to more MediaTek clk drivers
- deduplicate Allwinner ccu_clks arrays
- Allwinner H6 GPU DFS support
- Adjust Allwinner Kconfig to limit choice
- Fix initconst confusion on Renesas R-Car Gen4
- Add GPT/POEG (PWM) clocks and resets on Renesas RZ/G2L
- Add PFC and WDT clocks and resets on Renesas RZ/V2M
- Add thermal, SDHI, Z (CPU core), PCIe, and HSCIF (serial) clocks on
Renesas R-Car S4-8"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (124 commits)
clk: fixed-factor: Introduce *clk_hw_register_fixed_factor_parent_hw()
clk: mux: Introduce devm_clk_hw_register_mux_parent_hws()
clk: divider: Introduce devm_clk_hw_register_divider_parent_hw()
clk: qcom: gcc-msm8994: use parent_hws for gpll0/4
clk: qcom: clk-rpm: convert to parent_data API
dt-bindings: clock: fix wrong clock documentation for qcom,rpmcc
clk: qcom: gcc-msm8939: Add missing USB HS system clock frequencies
clk: qcom: gcc-msm8939: Add missing MDSS MDP clock frequencies
clk: qcom: gcc-msm8939: Add missing CAMSS CPP clock frequencies
clk: qcom: gcc-msm8939: Fix venus0_vcodec0_clk frequency definitions
clk: qcom: gcc-msm8939: Add missing CAMSS CCI bus clock
clk: qcom: gcc-msm8939: Fix weird field spacing in ftbl_gcc_camss_cci_clk
clk: qcom: gdsc: Bump parent usage count when GDSC is found enabled
clk: qcom: Drop mmcx gdsc supply for dispcc and videocc
clk: qcom: fix build error initializer element is not constant
clk: sprd: Add dt-bindings include file for UMS512
dt-bindings: clk: sprd: Add bindings for ums512 clock controller
clk: sunxi-ng: sun50i: h6: Modify GPU clock configuration to support DFS
dt-bindings: clock: qcom,gcc-msm8996: add more GCC clock sources
clk: qcom: add support for SM8350 DISPCC
...
With the addition of clock-output-names, we can now unify the internal
clock naming for omap4 and 5 to follow the other TI SoCs.
We are still using legacy clkctrl names for omap4 and 5 based on the clock
manager name which is wrong. Instead, we want to use the clkctrl clock
based naming.
We must now also drop the legacy TI_CLK_CLKCTRL_COMPAT quirk for the
clkctrl clock.
This change will allow further devicetree warning cleanup as already
done for am3/4 and dra7.
Cc: linux-clk@vger.kernel.org
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220615064306.22254-1-tony@atomide.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
as is without any warranty of any kind whether express or implied
without even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable instead of a
found boolean [1].
This removes the need to use a found variable and simply checking if
the variable was set, can determine if the break/goto was hit.
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20220324071019.59483-1-jakobkoschel@gmail.com
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the purpose specific kcalloc() function instead of the argument
size * count in the kzalloc() function.
[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210904131714.2312-1-len.baker@gmx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We no longer have users for the compatibility clocks and we can drop them.
These are old duplicate clocks for what we using.
Depends-on: 31aa7056bb ("ARM: dts: Don't use legacy clock defines for dra7 clkctrl")
Depends-on: 9206a3af4f ("clk: ti: Move dra7 clock devices out of the legacy section")
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220203085618.16043-4-tony@atomide.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We no longer have users for the compatibility clocks and we can drop them.
These are old duplicate clocks for what we using.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220203085618.16043-3-tony@atomide.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We no longer have users for the compatibility clocks and we can drop them.
These are old duplicate clocks for what we using.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220203085618.16043-2-tony@atomide.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Let's update all the TI component clocks to use ti_dt_clk_name() instead
of devicetree node name if available.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220204071449.16762-9-tony@atomide.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Let's update the TI pll and clockdomain clocks to use ti_dt_clk_name()
instead of devicetree node name if available.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220204071449.16762-8-tony@atomide.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Let's create the clock alias based on the clock-output-names property if
available. Also the component clock drivers can use ti_dt_clk_name() in
the following patches.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220204071449.16762-7-tony@atomide.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Let's add ti_find_clock_provider() so we can use clock-output-names
to name the clock provider instead of relying on non-standard devicetree
node names.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220204071449.16762-5-tony@atomide.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If no reg property is specified for a TI clock, let's try to use the
parent clock node IO address. This way we can avoid duplicate devicetree
reg properties that cause warnings for unique_unit_address.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220204071449.16762-4-tony@atomide.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In preparation for making use of the clock-output-names, we want to
keep node around in ti_dt_clocks_register().
This change should not needed as a fix currently.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220204071449.16762-3-tony@atomide.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We can constify clkctrl_name in preparation for making use of the
clock-output-names property.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220204071449.16762-2-tony@atomide.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Make const pointer error a static const array, removes a dereference
and shrinks object code a little.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211127173036.150535-1-colin.i.king@gmail.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Declare ADC1 clkctrl which feeds the magnetic-reader/ADC1 hardware
module.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211015081506.933180-2-miquel.raynal@bootlin.com
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Yu Jiahua <yujiahua1@huawei.com>
Link: https://lore.kernel.org/r/20210616034826.37276-1-yujiahua1@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the omap2_dpll_round_rate routine attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The gpmc clock is needed to update omap5 to boot with genpd with the
related devicetree patches. The ocmc clock is currently not used but
let's add it so we have all the clocks for the l3main2 defined.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <kristo@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/gate.c:67: warning: Function parameter or member 'hw' not described in 'omap36xx_gate_clk_enable_with_hsdiv_restore'
drivers/clk/ti/gate.c:67: warning: Excess function parameter 'clk' description in 'omap36xx_gate_clk_enable_with_hsdiv_restore'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-17-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll.c:163: warning: Function parameter or member 'user' not described in '_register_dpll'
drivers/clk/ti/dpll.c:163: warning: Excess function parameter 'hw' description in '_register_dpll'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-16-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/clockdomain.c:107: warning: Function parameter or member 'hw' not described in 'omap2_init_clk_clkdm'
drivers/clk/ti/clockdomain.c:107: warning: Excess function parameter 'clk' description in 'omap2_init_clk_clkdm'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210120093040.1719407-14-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll44xx.c:114: warning: Function parameter or member 'hw' not described in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:114: warning: Function parameter or member 'parent_rate' not described in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:114: warning: Excess function parameter 'clk' description in 'omap4_dpll_regm4xen_recalc'
drivers/clk/ti/dpll44xx.c:150: warning: Function parameter or member 'hw' not described in 'omap4_dpll_regm4xen_round_rate'
drivers/clk/ti/dpll44xx.c:150: warning: Function parameter or member 'parent_rate' not described in 'omap4_dpll_regm4xen_round_rate'
drivers/clk/ti/dpll44xx.c:150: warning: Excess function parameter 'clk' description in 'omap4_dpll_regm4xen_round_rate'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-11-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/dpll3xxx.c:414: warning: Function parameter or member 'hw' not described in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:414: warning: Function parameter or member 'parent_rate' not described in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:414: warning: Excess function parameter 'clk' description in 'omap3_dpll_recalc'
drivers/clk/ti/dpll3xxx.c:437: warning: Function parameter or member 'hw' not described in 'omap3_noncore_dpll_enable'
drivers/clk/ti/dpll3xxx.c:437: warning: Excess function parameter 'clk' description in 'omap3_noncore_dpll_enable'
drivers/clk/ti/dpll3xxx.c:479: warning: Function parameter or member 'hw' not described in 'omap3_noncore_dpll_disable'
drivers/clk/ti/dpll3xxx.c:479: warning: Excess function parameter 'clk' description in 'omap3_noncore_dpll_disable'
drivers/clk/ti/dpll3xxx.c:755: warning: Function parameter or member 'hw' not described in 'omap3_clkoutx2_recalc'
drivers/clk/ti/dpll3xxx.c:755: warning: Function parameter or member 'parent_rate' not described in 'omap3_clkoutx2_recalc'
drivers/clk/ti/dpll3xxx.c:755: warning: Excess function parameter 'clk' description in 'omap3_clkoutx2_recalc'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-4-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/clk/ti/clkt_dpll.c:284: warning: Function parameter or member 'hw' not described in 'omap2_dpll_round_rate'
drivers/clk/ti/clkt_dpll.c:284: warning: Function parameter or member 'parent_rate' not described in 'omap2_dpll_round_rate'
drivers/clk/ti/clkt_dpll.c:284: warning: Excess function parameter 'clk' description in 'omap2_dpll_round_rate'
Cc: Tero Kristo <kristo@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210126124540.3320214-3-lee.jones@linaro.org
Reviewed-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
ability to get struct clk pointers from a struct clk_hw so that clk providers
can consume the clks they provide, if they need to do something like that. This
has been a long missing part of the clk provider API that will help us move
away from exposing a struct clk pointer in the struct clk_hw. Tracepoints are
added for the clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to help
developers understand the hardware enable state of clks in case firmware or
bootloader state is different than what is expected. Overall the core changes
are mostly improving the clk driver writing experience.
At the driver level, we have the usual collection of driver updates and new
drivers for new SoCs. This time around the Qualcomm folks introduced a good
handful of clk drivers for various parts of three or four SoCs. The SiFive
folks added a new clk driver for their FU740 SoCs, coming in second on the
diffstat and then Atmel AT91 and Amlogic SoCs had lots of work done after that
for various new features. One last thing to note in the driver area is that the
i.MX driver has gained a new binding to support SCU clks after being on the
list for many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and tweaks that
come from more testing and finding out that some configuration was wrong or
that a driver could support being built as a module.
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks
-----BEGIN PGP SIGNATURE-----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=Wt9O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework got some nice improvements this time around. We
gained the ability to get struct clk pointers from a struct clk_hw so
that clk providers can consume the clks they provide, if they need to
do something like that. This has been a long missing part of the clk
provider API that will help us move away from exposing a struct clk
pointer in the struct clk_hw. Tracepoints are added for the
clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to
help developers understand the hardware enable state of clks in case
firmware or bootloader state is different than what is expected.
Overall the core changes are mostly improving the clk driver writing
experience.
At the driver level, we have the usual collection of driver updates
and new drivers for new SoCs. This time around the Qualcomm folks
introduced a good handful of clk drivers for various parts of three or
four SoCs. The SiFive folks added a new clk driver for their FU740
SoCs, coming in second on the diffstat and then Atmel AT91 and Amlogic
SoCs had lots of work done after that for various new features. One
last thing to note in the driver area is that the i.MX driver has
gained a new binding to support SCU clks after being on the list for
many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and
tweaks that come from more testing and finding out that some
configuration was wrong or that a driver could support being built as
a module.
Summary:
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
dt-binding: clock: Document canaan,k210-clk bindings
dt-bindings: Add Canaan vendor prefix
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
clk: ingenic: Fix divider calculation with div tables
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
clk: si5351: Wait for bit clear after PLL reset
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
...
Having the ABE DPLL ref and bypass muxes set to different inputs was
causing the DPLL not to lock when TIMER8 was used, as it is in the Pyra
for the backlight.
This patch fixes this by setting abe_dpll_bypass_clk_mux to sys_32k_ck
in omap5xxx_dt_clk_init.
A similar patch may also be needed for OMAP44xx which has similar code
in omap4xxx_dt_clk_init, but I have not added this as I have no hardware
to test on.
Signed-off-by: David Shah <dave@ds0.me>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/1d3abe2512054866cc2ea7b2592238f4fa06502a.1607253531.git.hns@goldelico.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If clk_register fails, we should goto free branch
before function returns to prevent memleak.
Fixes: 163152cbbe ("clk: ti: Add support for FAPLL on dm816x")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201113131623.2098222-1-zhangqilong3@huawei.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Similar to what we've done for IPU and DSP let's ignore the status bit
for the IVA clkctrl register.
The clkctrl status won't change unless the related rstctrl is deasserted,
and the rstctrl status won't change unless the clkctrl is enabled.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to what we've done for IPU and DSP let's ignore the status bit
for the IVA clkctrl register.
The clkctrl status won't change unless the related rstctrl is deasserted,
and the rstctrl status won't change unless the clkctrl is enabled.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for suspend and resume to work with genpd on am4, we must keep
l3 main clock always on. Otherwise prm_omap driver will shut down the l3
main clock on suspend when simple-pm-bus and GENPD_FLAG_PM_CLK are used.
Note that we already keep the l3 main clock always on with the legacy
platform code.
Later on we may want to start managing the l3 main clock with a dedicated
interconnect driver instead of using simple-pm-bus and GENPD_FLAG_PM_CLK.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for suspend and resume to work with genpd on am3, we must keep
l3 main clock always on. Otherwise prm_omap driver will shut down the l3
main clock on suspend when simple-pm-bus and GENPD_FLAG_PM_CLK are used.
Note that we already keep the l3 main clock always on with the legacy
platform code.
Later on we may want to start managing the l3 main clock with a dedicated
interconnect driver instead of using simple-pm-bus and GENPD_FLAG_PM_CLK.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a memory leak induced by not calling clk_put after doing of_clk_get.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907082600.454-3-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clk pointer passed to omap2_clk_(deny|allow)_idle can be NULL, so
add checks for this.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20200907082600.454-2-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
function that isn't used anymore. Otherwise the main new thing for the common
clk framework is that it is selectable in the Kconfig language now. Hopefully
this will let clk drivers and clk consumers be testable on more than the
architectures that support the clk framework. The goal is to introduce some
Kunit tests for the framework.
Outside of the core framework we have the usual set of various driver updates
and non-critical fixes. The dirstat shows that the new Baikal-T1 driver is the
largest addition this time around in terms of lines of code. After that the x86
(Intel), Qualcomm, and Mediatek drivers introduce many lines to support new or
upcoming SoCs. After that the dirstat shows the usual suspects working on their
SoC support by fixing minor bugs, correcting data and converting some of their
DT bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix clock support
on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and clk-pllv3
drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support aarch32 mode on
aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using composite
clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102 defined
bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAl7gEUgRHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSUemxAAlQKzx0yMS3yx5twJ4RSFUvf3hf4OqyPp
O46soqADk+l69Z4SUUBsMjt8el5Sqmm4d1j1Gpfmgp3ZlumHCQK+qGYp48IXbwRP
Jlo5sKNlNL6yhCd+ixPn4j7W/HbpGs4cciWOXkGQtYEGjhHm3Wllhd9MqpL2YjLx
gZW60NqWtOe1XeB4ILyYQGisNwAGDi5XuBeNvxG12H/LaGC1mwtBX9yoNAehr9bF
peJ2XnO02zFo73OCyzIOkw1uY4u7ZtwPdHGhymoGeVlcBWO6KwKesNkHnji/Grlv
wMbsGLoRV/i3PL3q5kZIDigo8sqZ9RUG+9piRAoiLM5AgkSypw3/q9T+ujTfZp8t
kgvFha6bLZz31UFmr4lBJPTT5Q/hAoe1W6RB6HZkx7XNqUpsAS04SwkQztAqkJqZ
9zlYJrXgLlP5qcNllJ6zvUWkMqtmIKW4ZkjYe4u84yk5Co7bX8DCYa+QOKCz+pV4
IbjRT62OrX2ZlXJYwkLb4m1nhZ7tBzhzIRP1umL0ukhxdomK6ofSNPzbBF9+t1eR
/ai2/Ch6L6WIwDINEp+chO67/dJaj5W3WNqGMCmVt37myW1kBjH3eg0YG4cp7NYZ
/jSjdWczQy/8BgY5V1009MRXI4uyazQxBw+apDcIGezamOKBmuwjBcvkf1D0mL2x
Y6OclK5ljsw=
=nuG5
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
Fix the following gcc warning:
drivers/clk/ti/clk-7xx.c:320:43: warning: ‘dra7_gpu_sys_clk_data’
defined but not used [-Wunused-const-variable=]
static const struct omap_clkctrl_div_data dra7_gpu_sys_clk_data
__initconst = {
^~~~~~~~~~~~~~~~~~~~~
drivers/clk/ti/clk-7xx.c:315:27: warning: ‘dra7_gpu_sys_clk_parents’
defined but not used [-Wunused-const-variable=]
static const char * const dra7_gpu_sys_clk_parents[] __initconst = {
^~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lkml.kernel.org/r/20200417073523.42520-1-yanaijie@huawei.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We need sysclk6_ck enabled early as it is needed by l4_ls and system
timers early on boot. This removes the dependency of system timers to
the interconnect related code that can be then probed later on when
suitable at module_init time.
Cc: linux-clk@vger.kernel.org
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This clock entry does not exist on any other devices except DRA76,
so mark it as specific to that SoC only.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200430083640.8621-3-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
gpu_cm:* parent clock name is wrong, replace this with correct
gpu-clkctrl:* clock. Otherwise the clock ends up in the orphaned list.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200430083640.8621-2-t-kristo@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
L4 secure clocks do not have their parents set currently, which ends
them up to the orphan clock list. Fix this by adding either l3 or l4
clock as their parent.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Link: https://lkml.kernel.org/r/20200429131341.4697-4-t-kristo@ti.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Linus Torvalds