Introduce ramc_lpr to struct at91_reset. This will lead to the
unification of at91sam9260_restart() and at91sam9g45_restart().
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use r4 as temporary register. On ARM r0-r3 should be used to hold
function arguments.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce args member in struct at91_reset_data. It stores the value
that needs to be written in mode register so that the reboot actions
to happen. With these changes samx7_restart() could be removed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce struct at91_reset_data to be able to provide per SoC
data. At the moment this being only notifier callback.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Allocate at91_reset data on probe and set it as platform data.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add new argument to at91_reset_status() that is the pointer to reset
controller base address.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Convert reset in pointer to struct at91_reset.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce struct at91_reset intended to keep all the at91 reset controller
data.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some HP Pavilion x2 10 models use an AXP288 for charging and fuel-gauge.
We use a native power_supply / PMIC driver in this case, because on most
models with an AXP288 the ACPI AC / Battery code is either completely
missing or relies on custom / proprietary ACPI OpRegions which Linux
does not implement.
The native drivers mostly work fine, but there are 2 problems:
1. These model uses a Type-C connector for charging which the AXP288 does
not support. As long as a Type-A charger (which uses the USB data pins for
charger type detection) is used everything is fine. But if a Type-C
charger is used (such as the charger shipped with the device) then the
charger is not recognized.
So we end up slowly discharging the device even though a charger is
connected, because we are limiting the current from the charger to 500mA.
To make things worse this happens with the device's official charger.
Looking at the ACPI tables HP has "solved" the problem of the AXP288 not
being able to recognize Type-C chargers by simply always programming the
input-current-limit at 3000mA and relying on a Vhold setting of 4.7V
(normally 4.4V) to limit the current intake if the charger cannot handle
this.
2. If no charger is connected when the machine boots then it boots with the
vbus-path disabled. On other devices this is done when a 5V boost converter
is active to avoid the PMIC trying to charge from the 5V boost output.
This is done when an OTG host cable is inserted and the ID pin on the
micro-B receptacle is pulled low, the ID pin has an ACPI event handler
associated with it which re-enables the vbus-path when the ID pin is pulled
high when the OTG cable is removed. The Type-C connector has no ID pin,
there is no ID pin handler and there appears to be no 5V boost converter,
so we end up not charging because the vbus-path is disabled, until we
unplug the charger which automatically clears the vbus-path disable bit and
then on the second plug-in of the adapter we start charging.
The HP Pavilion x2 10 models with an AXP288 do have mostly working ACPI
AC / Battery code which does not rely on custom / proprietary ACPI
OpRegions. So one possible solution would be to blacklist the AXP288
native power_supply drivers and add the HP Pavilion x2 10 with AXP288
DMI ids to the list of devices which should use the ACPI AC / Battery
code even though they have an AXP288 PMIC. This would require changes to
4 files: drivers/acpi/ac.c, drivers/power/supply/axp288_charger.c,
drivers/acpi/battery.c and drivers/power/supply/axp288_fuel_gauge.c.
Beside needing adding the same DMI matches to 4 different files, this
approach also triggers problem 2. from above, but then when suspended,
during suspend the machine will not wakeup because the vbus path is
disabled by the AML code when not charging, so the Vbus low-to-high
IRQ is not triggered, the CPU never wakes up and the device does not
charge even though the user likely things it is charging, esp. since
the charge status LED is directly coupled to an adapter being plugged
in and does not reflect actual charging.
This could be worked by enabling vbus-path explicitly from say the
axp288_charger driver's suspend handler.
So neither situation is ideal, in both cased we need to explicitly enable
the vbus-path to work around different variants of problem 2 above, this
requires a quirk in the axp288_charger code.
If we go the route of using the ACPI AC / Battery drivers then we need
modifications to 3 other drivers; and we need to partially disable the
axp288_charger code, while at the same time keeping it around to enable
vbus-path on suspend.
OTOH we can copy the hardcoding of 3A input-current-limit (we never touch
Vhold, so that would stay at 4.7V) to the axp288_charger code, which needs
changes regardless, then we concentrate all special handling of this
interesting device model in the axp288_charger code. That is what this
commit does.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1791098
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Intel Compute Stick `STK1A32SC` can have a system vendor of
"Intel(R) Client Systems".
Broaden the Intel Compute Stick DMI checks so that they match "Intel
Corporation" as well as "Intel(R) Client Systems".
This fixes an issue where the STK1A32SC compute sticks were still
exposing a battery with the existing blacklist entry.
Signed-off-by: Jeffery Miller <jmiller@neverware.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Allow charger manager can be built as a module like other charger
drivers.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add the POWER_SUPPLY_PROP_CHARGE_NOW attribute to allow user to get
current battery capacity (uAh) to do measurement.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Don't print an error message if devm_power_supply_register() returns
-EPROBE_DEFER, since the driver will simply re-probe later.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There's a bug on ACPI platforms where host events from the ECPD ACPI
device never make their way to the cros-ec-usbpd-charger driver. This
makes it so the only time the charger driver updates its state is when
user space accesses its sysfs attributes.
Now that these events have been unified into a single notifier chain on
both ACPI and non-ACPI platforms, update the charger driver to use this
new notifier.
Reviewed-by: Benson Leung <bleung@chromium.org>
Co-Developed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Jon Flatley <jflat@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60.
-----BEGIN PGP SIGNATURE-----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=fIjZ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: OMAP2+: Fix undefined reference to omap_secure_init
ARM: s3c64xx: Drop unneeded select of TIMER_OF
ARM: exynos: Drop unneeded select of MIGHT_HAVE_CACHE_L2X0
ARM: s3c24xx: Switch to atomic pwm API in rx1950
ARM: OMAP2+: sleep43xx: Call secure suspend/resume handlers
ARM: OMAP2+: Use ARM SMC Calling Convention when OP-TEE is available
ARM: OMAP2+: Introduce check for OP-TEE in omap_secure_init()
ARM: OMAP2+: Add omap_secure_init callback hook for secure initialization
ARM: at91: Documentation: add sam9x60 product and datasheet
ARM: at91: pm: use of_device_id array to find the proper shdwc node
ARM: at91: pm: use SAM9X60 PMC's compatible
ARM: imx: only select ARM_ERRATA_814220 for ARMv7-A
ARM: zynq: use physical cpuid in zynq_slcr_cpu_stop/start
ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume
ARM: tegra: Modify reshift divider during LP1
ARM: tegra: Enable PLLP bypass during Tegra124 LP1
ARM: samsung: Rename Samsung and Exynos to lowercase
ARM: exynos: Correct the help text for platform Kconfig option
ARM: bcm: Select ARM_AMBA for ARCH_BRCMSTB
ARM: brcmstb: Add debug UART entry for 7216
...
Update the recently merged CPR (Core Power Reduction) support in the
AVS (Adaptive Voltage Scaling) subsystem (Brendan Higgins, Nathan
Chancellor, Niklas Cassel) and the rockchip-io AVS driver (Heiko
Stuebner), add two more module parameters to intel_idle on top of the
recently merged material, clean up a piece of cpuidle documentation
and consolidate system sleep states documentation (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl49O1kSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRx7OMP/34DA5zPXhughdawhrw4z9N8Xl/VKbva
k6wr26C4Bwrd19i4MU6LdrjbbMBfbg7gsUtuO/sF9dXjsFlcMrfsgsdIO5QH26qL
yD68wwv/F7/MWUWhY7wVcTI5bnBnS1WF6ygnhRCfhI7R7Zq/WWQwK6D9/yZG/9uo
AfTEv+yfXSBg+ByzaFqYt7S6QTTnUPrp29ROOJNE7Eryz2n1S9cSxCZPAQbqVNfr
0SRX9EPUNkNTYfR+QEtIs6uXrCWpbAePdxenirRYMvTYidjDvWG3kXNp+MlwR9co
ieiYmCELOnlmYXu2vOPmBWW5rnxP+4aQuOVpuCPRxRwecKUxZwcGL0eh7e4A0wP8
/WwiTHyKphlqPWSaYvWKWDI2razDNnFnqkmXgfb68rAZNUNRRMbTErHzu2w4A1vj
NiGCWqR+5Wimp4Ztk/WfFQYxPb2wr+a8PdwNWtH03goB2JOvHSZbNCB+BqX0yJJt
GECDn6mFKCqJRQXfsxa+RIrVj3oXouExlb6VtKc3AHPSn+XyzQgRbo+CH0XvTnNI
uoiL3PY4ayR6WBJjveRW9lLw3Acul475O1Xd0OzCNx2gsD6cRG7sE9cj4vRltdpl
qW/t7vkS4JiqASgQEfZui4EZFxIk0Brv9v7KNl43bIcyW5SCkyjAbWeCR18I9l6l
kxn8zXSTxtKZ
=Yc9a
-----END PGP SIGNATURE-----
Merge tag 'pm-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
- Update the recently merged CPR (Core Power Reduction) support in the
AVS (Adaptive Voltage Scaling) subsystem (Brendan Higgins, Nathan
Chancellor, Niklas Cassel)
- Update the rockchip-io AVS driver (Heiko Stuebner)
- Add two more module parameters to intel_idle on top of the recently
merged material (Rafael Wysocki)
- Clean up a piece of cpuidle documentation and consolidate system
sleep states documentation (Rafael Wysocki)
* tag 'pm-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Documentation: Clean up PM QoS description
Documentation: admin-guide: PM: Update sleep states documentation
intel_idle: Introduce 'states_off' module parameter
intel_idle: Introduce 'use_acpi' module parameter
power: avs: qcom-cpr: Avoid clang -Wsometimes-uninitialized in cpr_scale
power: avs: qcom-cpr: add unspecified HAS_IOMEM dependency
PM / AVS: rockchip-io: fix the supply naming for the emmc supply on px30
power: avs: qcom-cpr: add a printout after the driver has been initialized
* CrOS EC
- Refactoring of some of cros_ec's headers. include/linux/mfd/cros_ec.h now
removed, new cros_ec.h added drivers/platform/chrome which contains shared
operations of cros_ec transport drivers.
- Response tracing in cros_ec_proto
* Wilco EC
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
* Misc
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXjij4AAKCRBzbaomhzOw
wrFjAP0bU5PFkxprCOTY9kF/cMgHPDljEPES4FVV11eGyYr3HgD/StpuIhFGrh7+
Fz96dDdNu1melyGjmMqSN/M9JFo+Hw4=
=FB/I
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Refactoring of some of cros_ec's headers:
include/linux/mfd/cros_ec.h now removed, new cros_ec.h added to
drivers/platform/chrome which contains shared operations of cros_ec
transport drivers.
- Response tracing in cros_ec_proto
Wilco EC:
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard
backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
Misc:
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device"
* tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec: Match implementation with headers
platform/chrome: cros_ec: Drop unaligned.h include
platform/chrome: wilco_ec: Allow wilco to be compiled in COMPILE_TEST
platform/chrome: wilco_ec: Add newlines to printks
platform/chrome: wilco_ec: Fix unregistration order
cros_ec: treewide: Remove 'include/linux/mfd/cros_ec.h'
platform/chrome: cros_ec_ishtp: Make init_lock static
platform/chrome: chromeos_laptop: Convert to i2c_new_scanned_device
platform/chrome: cros_ec_lpc: Use platform_get_irq_optional() for optional IRQs
platform/chrome: cros_ec_proto: Add response tracing
platform/chrome: cros_ec_trace: Match trace commands with EC commands
Clang warns (trimmed for brevity):
../drivers/power/avs/qcom-cpr.c:570:13: warning: variable 'reg_mask' is
used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
../drivers/power/avs/qcom-cpr.c:520:13: warning: variable 'new_uV' is
used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
Due to the fact that Clang's static analysis happens before any
optimization passes are taken into account, it cannot see that both
branches in the if statement must be taken because dir cannot be
something other than UP or DOWN due to the check at the top of this
function. Change the else if condition to else to fix this false
positive.
Fixes: bf6910abf5 ("power: avs: Add support for CPR (Core Power Reduction)")
Link: https://github.com/ClangBuiltLinux/linux/issues/840
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently CONFIG_QCOM_CPR=y implicitly depends on CONFIG_HAS_IOMEM=y;
consequently, on architectures without IOMEM we get the following build
error:
/usr/bin/ld: drivers/power/avs/qcom-cpr.o: in function `cpr_probe':
drivers/power/avs/qcom-cpr.c:1690: undefined reference to `devm_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The supply going to the emmc/flash is named vccio6, not vccio0 and while
the code does this correctly already, the comments and error output do not.
So just change these values to the correct ones.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to easier inform the user that the driver has been initialized
successfully, add a printout after the driver has been initialized.
At the same time, remove a dev_dbg() that is now redundant.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently a read failure by bq25890_field_read on F_DEV_REV is returning
an error in id instead of rev. Fix this by returning the value in rev.
Addresses-Coverity: ("Copy-paste error")
Fixes: d20267c9a9 ("power: supply: bq25890_charger: Add support of BQ25892 and BQ25896 chips")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Investigation on the AXP803 shows that VBUS_PLUGIN/VBUS_REMOVAL IRQs are
triggered on the rising/falling edge of AXP20X_PWR_STATUS_VBUS_USED. The
reason IRQs do not arrive while N_VBUSEN/DRIVEVBUS is high is because
AXP20X_PWR_STATUS_VBUS_USED also never goes high.
This also means that if VBUS is online, a VBUS_REMOVAL IRQ is received
immediately on setting N_VBUSEN/DRIVEVBUS high (and VBUS_PLUGIN shortly
after it is set back low). This was also verified to be the case when
manually offlining VBUS through AXP20X_VBUS_PATH_SELECT.
As long as VBUS is online, a present->absent transition necessarily
implies an online->offline transition. Since will cause an IRQ, there is
no need to poll while VBUS is online.
To ensure the driver's view of VBUS online status remains accurate,
unconditionally poll once when receiving an IRQ and when resuming. If
VBUS is still online at that time, polling will cease until the next
VBUS_REMOVAL IRQ.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The USB power supply input can be used as a wakeup source. Hook up the
VBUS_PLUGIN IRQ to trigger wakeup based on userspace configuration.
To do this, we must remember the list of IRQs for the life of the
device. To know how much space to allocate for the flexible array
member, we switch from using a NULL sentinel to using an array length.
Because we now depend on the specific order of the IRQs (we assume
VBUS_PLUGIN is first and always present), failing to acquire an IRQ
during probe must be a fatal error.
To avoid spuriously waking up the system when the USB power supply is
not configured as a wakeup source, we must explicitly disable all non-
wake IRQs during system suspend. This is because the SoC's NMI input is
shared among all IRQs on the AXP PMIC. Due to the use of regmap-irq, the
individual IRQs within the PMIC are nested threaded interrupts, and are
therefore not automatically disabled during system suspend.
The upshot is that if any other device within the MFD (such as the power
key) is an enabled wakeup source, all enabled IRQs within the PMIC will
cause wakeup. We still need to call enable_irq_wake() when we *do* want
wakeup, in case those other wakeup sources on the PMIC are all disabled.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
AXP803/AXP813 have a flag that enables/disables the USB power supply
input. Allow control of this flag via the ONLINE property on those
variants.
It may be necessary to offline the USB power supply input when using
the USB port in OTG mode, or to allow userspace to disable charging.
When the USB VBUS input is disabled via the PATH_SEL bit, the VBUS_USED
bit in PWR_INPUT_STATUS is cleared, so there is no change needed when
getting the property.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of ad-hoc variant ID checks throughout the code, let's start
moving the variant-specific details to a match structure. This allows
for future flexibility, and it better matches the other axp20x power
supply drivers.
This commit removes most variant checks from axp20x_usb_power_probe().
Other parts of the driver still do ID matching; they are left unchanged
for now.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following sparse warning:
drivers/power/supply/ucs1002_power.c:492:5: warning: symbol 'ucs1002_regulator_enable' was not declared. Should it be static?
Fixes: a3d70dacc7 ("power: suppy: ucs1002: disable power when max current is 0")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SAM9X60's PMC uses different offset for master clock register.
Add a member of type struct pmc_reg_config in struct reg_config,
fill it correspondingly for SAMA5D2 and SAM9X60 and use it in
poweroff() function.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver uses AT91_PMC_MCKR in poweroff() function. But the
SAM9X60's PMC versions maps AT91_PMC_MCKR functionality at different
offset compared to the SAMA5D2's one. This patch prepares the field
so that different AT91_PMC_MCKR's offsets to be introduced in
struct reg_config so that proper offset to be used for AT91_PMC_MCKR
based on compatible string.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add bq25892, bq25895 and bq25896 to list of supported device IDs for
DeviceTree and I2C.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Support BQ25892 and BQ25896 chips by this driver. They shared one chip
ID 0, so distinquish them by device revisions (2 for 25896 and 1 for
25892).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The "mode" variable is an enum and in this context GCC treats it as an
unsigned int so the error handling is never triggered.
Fixes: 51d0756604 ("bq20z75: Add support for charge properties")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver's remove path calls cancel_delayed_work().
However, that function does not wait until the work function
finishes. This could mean that the work function is still
running after the driver's remove function has finished,
which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
that the work is properly cancelled, no longer running, and
unable to re-schedule itself.
This issue was detected with the help of Coccinelle.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This member of struct axp20x_usb_power is not used anywhere.
Remove it.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AC power supply input can be used as a wakeup source. Hook up the
ACIN_PLUGIN IRQ to trigger wakeup based on userspace configuration.
To do this, we must remember the list of IRQs for the life of the
device. To know how much space to allocate for the flexible array
member, we switch from using a NULL sentinel to using an array length.
Because we now depend on the specific order of the IRQs (we assume
ACIN_PLUGIN is first and always present), failing to acquire an IRQ
during probe must be a fatal error.
To avoid spuriously waking up the system when the AC power supply is
not configured as a wakeup source, we must explicitly disable all non-
wake IRQs during system suspend. This is because the SoC's NMI input is
shared among all IRQs on the AXP PMIC. Due to the use of regmap-irq, the
individual IRQs within the PMIC are nested threaded interrupts, and are
therefore not automatically disabled during system suspend.
The upshot is that if any other device within the MFD (such as the power
key) is an enabled wakeup source, all enabled IRQs within the PMIC will
cause wakeup. We still need to call enable_irq_wake() when we *do* want
wakeup, in case those other wakeup sources on the PMIC are all disabled.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
AXP803/AXP813 have a flag that enables/disables the AC power supply
input. Allow control of this flag via the ONLINE property on those
variants.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
AXP803/AXP813 have a flag that enables/disables the AC power supply
input. This flag does not affect the status bits in PWR_INPUT_STATUS.
Its effect can be verified by checking the battery charge/discharge
state (bit 2 of PWR_INPUT_STATUS), or by examining the current draw on
the AC input.
Take this flag into account when getting the ONLINE property of the AC
input, on PMICs where this flag is present.
Fixes: 7693b5643f ("power: supply: add AC power supply driver for AXP813")
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This header file now only includes the cros_ec_dev struct, however, is the
'include/linux/platform_data/cros_ec_proto.h' who contains the definition of
all the Chrome OS EC related structs. There is no reason to have a
separate include for this struct so move to the place where other
structs are defined. That way, we can remove the include itself, but also
simplify the common pattern
#include <linux/mfd/cros_ec.h>
#include <linux/platform_data/cros_ec_proto.h>
for a single include
#include <linux/platform_data/cros_ec_proto.h>
The changes to remove the cros_ec.h include were generated with the
following shell script:
git grep -l "<linux/mfd/cros_ec.h>" | xargs sed -i '/<linux\/mfd\/cros_ec.h>/d'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Currently when the call cpr_read_fuse_uV returns an error the value in the
uninitialized variable ret is returned. Fix this by instread returning the
error value in the variable uV.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: bf6910abf5 ("power: avs: Add support for CPR (Core Power Reduction)")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
drivers/power/avs/qcom-cpr.c:1081:15:
warning: no previous prototype for ‘cpr_get_opp_hz_for_req’
Detected when running make with W=1.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
drivers/power/avs/qcom-cpr.c:896:35:
warning: variable ‘prev’ set but not used
Detected when running make with W=1.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
drivers/power/avs/qcom-cpr.c:402:4:
error: implicit declaration of function ‘regmap_multi_reg_write’
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
drivers/power/avs/qcom-cpr.c:838:15:
warning: format ‘%ld’ expects argument of type ‘long int’, but argument 6 has type ‘ssize_t’
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPR (Core Power Reduction) is a technology that reduces core power on a
CPU or other device. It reads voltage settings in efuse from product
test process as initial settings.
Each OPP corresponds to a "corner" that has a range of valid voltages
for a particular frequency. While the device is running at a particular
frequency, CPR monitors dynamic factors such as temperature, etc. and
adjusts the voltage for that frequency accordingly to save power
and meet silicon characteristic requirements.
This driver is based on an RFC by Stephen Boyd[1], which in turn is
based on work by others on codeaurora.org[2].
[1] https://lkml.org/lkml/2015/9/18/833
[2] https://source.codeaurora.org/quic/la/kernel/msm-4.14/tree/drivers/regulator/cpr-regulator.c?h=msm-4.14
Co-developed-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
"Battery mode" is the name of the register, the bit manipulated by this
code is "CAPACITY_MODE" (Smart Battery System Specifications).
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When a device has no support to get the charger number of ports, it
doesn't have to result in a dev_err(), print saying "Could not get
charger port count" using a dev_info() would suffice. In such case,
the dev_info() message is already printed but the dev_err() is annoying,
specially, on those devices that doesn't support the command. So remove
the dev_err().
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Notify core through power_supply_changed() in case of changes in state
of charge and power supply status. This is useful for user-space to
efficiently update current battery level.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
For configuration of fuel gauge alert for a low level state of charge
interrupt we add a function to config level threshold and a device tree
binding property to set it in flatned device tree node.
Now we can use "maxim,alert-low-soc-level" property with the values from
1% up to 32% to configure alert interrupt threshold.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
According datasheet max17040 has a pin for alert host for low SOC.
This pin can be used as external interrupt, so we need to check for
interrupts assigned for device and handle it.
In handler we are checking and storing fuel gauge registers values
and send an uevent to notificate user space, so user space can decide
save work or turn off since the alert demonstrate that the battery may
no have the power to keep the system turned on for much longer.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are some deviations between the real resistance and the ideal
resistance of coulomb counter, which will affect the accuracy of
the coulomb counter, thus calibrate the real resistance of coulomb
counter to improve the accuracy.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Optimize the battery internal resistance in a certain temerature to
get a accurate battery internal resistance.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since the battery internal resistance can be changed with the temperature
changes, thus add a resistance temperature table support to look up
the accurate battery internal resistance in a certain temperature.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We need the of_match table if we want to use the compatible string in
the pmic's child node and get the charger driver loaded automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The MAX17055 is very similar to the MAX17042 so extend the driver.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
For some devices userspace needs the ability to completely cut the power
to the USB devices connected to the charge controller. An easy way to
achieve this is by allowing 0 as a valid max current and forcibly disable
the output in that case, as well as enable it again if the regulator is
in use and a non-0 max current is set.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The ADC in the JZ4740 can work either in high-precision mode with a 2.5V
range, or in low-precision mode with a 7.5V range. The code in place in
this driver will select the proper scale according to the maximum
voltage of the battery.
The JZ4770 however only has one mode, with a 6.6V range. If only one
scale is available, there's no need to change it (and nothing to change
it to), and trying to do so will fail with -EINVAL.
Fixes: fb24ccfbe1 ("power: supply: add Ingenic JZ47xx battery driver.")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Artur Rojek <contact@artur-rojek.eu>
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver forgets to unregister the notifier in remove.
Add the call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Don't generate an error message when devm_gpiod_get fails with
-EPROBE_DEFER.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
- Avoid a race condition in the ACPI EC driver that may cause
systems to be unable to leave suspend-to-idle (Rafael Wysocki).
- Drop the "disabled" field, which is redundant, from struct
cpuidle_state (Rafael Wysocki).
- Reintroduce device PM QoS frequency constraints (temporarily
introduced and than dropped during the 5.4 cycle) in preparation
for adding QoS support to devfreq (Leonard Crestez).
- Clean up indentation (in multiple places) and the cpuidle drivers
help text in Kconfig (Krzysztof Kozlowski, Randy Dunlap).
-----BEGIN PGP SIGNATURE-----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=KAyd
-----END PGP SIGNATURE-----
Merge tag 'pm-5.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull additional power management updates from Rafael Wysocki:
"These fix an ACPI EC driver bug exposed by the recent rework of the
suspend-to-idle code flow, reintroduce frequency constraints into
device PM QoS (in preparation for adding QoS support to devfreq), drop
a redundant field from struct cpuidle_state and clean up Kconfig in
some places.
Specifics:
- Avoid a race condition in the ACPI EC driver that may cause systems
to be unable to leave suspend-to-idle (Rafael Wysocki)
- Drop the "disabled" field, which is redundant, from struct
cpuidle_state (Rafael Wysocki)
- Reintroduce device PM QoS frequency constraints (temporarily
introduced and than dropped during the 5.4 cycle) in preparation
for adding QoS support to devfreq (Leonard Crestez)
- Clean up indentation (in multiple places) and the cpuidle drivers
help text in Kconfig (Krzysztof Kozlowski, Randy Dunlap)"
* tag 'pm-5.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Rework ACPI events synchronization
ACPI: EC: Rework flushing of pending work
PM / devfreq: Add missing locking while setting suspend_freq
PM / QoS: Restore DEV_PM_QOS_MIN/MAX_FREQUENCY
PM / QoS: Reorder pm_qos/freq_qos/dev_pm_qos structs
PM / QoS: Initial kunit test
PM / QoS: Redefine FREQ_QOS_MAX_DEFAULT_VALUE to S32_MAX
power: avs: Fix Kconfig indentation
cpufreq: Fix Kconfig indentation
cpuidle: minor Kconfig help text fixes
cpuidle: Drop disabled field from struct cpuidle_state
cpuidle: Fix Kconfig indentation
- Add support for a "resource managed strongly uncachable ioremap" call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
- New Drivers
- Add support for MediaTek MT6323 PMIC
- New Device Support
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
- New Functionality
- Add support for requested supply clocks; madera-core
- Fix-ups
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona, syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
- Bug Fixes
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc
-----BEGIN PGP SIGNATURE-----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=mugH
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for a "resource managed strongly uncachable ioremap"
call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
New Drivers:
- Add support for MediaTek MT6323 PMIC
New Device Support:
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC
CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
New Functionality:
- Add support for requested supply clocks; madera-core
Fix-ups:
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona,
syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
Bug Fixes:
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc"
* tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (47 commits)
Revert "mfd: syscon: Set name of regmap_config"
mfd: ti_am335x_tscadc: Fix static checker warning
mfd: bd70528: Staticize bit value definitions
mfd: mfd-core: Honour Device Tree's request to disable a child-device
dt-bindings: mfd: max77693: Fix missing curly brace
mfd: intel-lpss: Add Intel Comet Lake PCH-H PCI IDs
mfd: db8500-prcmu: Support U8420-sysclk firmware
dt-bindings: mfd: max77650: Convert the binding document to yaml
mfd: mfd-core: Move pdev->mfd_cell creation back into mfd_add_device()
mfd: mfd-core: Remove usage counting for .{en,dis}able() call-backs
x86: olpc-xo1-sci: Remove invocation of MFD's .enable()/.disable() call-backs
x86: olpc-xo1-pm: Remove invocation of MFD's .enable()/.disable() call-backs
mfd: mfd-core: Remove mfd_clone_cell()
mfd: mfd-core: Protect against NULL call-back function pointer
mfd: cs5535-mfd: Register clients using their own dedicated MFD cell entries
mfd: cs5535-mfd: Request shared IO regions centrally
mfd: cs5535-mfd: Remove mfd_cell->id hack
mfd: cs5535-mfd: Use PLATFORM_DEVID_* defines and tidy error message
mfd: intel_soc_pmic_crc: Add "cht_crystal_cove_pmic" cell to CHT cells
mfd: madera: Add support for requesting the supply clocks
...
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drivers:
* test_power: add support for current and charge_counter
* cpcap-charger: improve charge calculation and limit default charge voltage
* ab8500: convert to IIO
* misc. small fixes all over drivers
-----BEGIN PGP SIGNATURE-----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=iHhO
-----END PGP SIGNATURE-----
Merge tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- test_power: add support for current and charge_counter
- cpcap-charger: improve charge calculation and limit default charge
voltage
- ab8500: convert to IIO
- misc small fixes all over drivers
* tag 'for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (29 commits)
power: supply: bd70528: Add MODULE_ALIAS to allow module auto loading
power: supply: ab8500_charger: Fix inconsistent IS_ERR and PTR_ERR
power: supply: cpcap-charger: cpcap_charger_voltage_to_regval() can be static
power: supply: cpcap-battery: Add basic coulomb counter calibrate support
power: supply: cpcap-battery: Read and save integrator register CCI
power: supply: cpcap-battery: Simplify short term power average calculation
power: supply: cpcap-battery: Simplify coulomb counter calculation with div_s64
power: supply: cpcap-battery: Move coulomb counter units per lsb to ddata
power: supply: cpcap-charger: Allow changing constant charge voltage
power: supply: cpcap-battery: Fix handling of lowered charger voltage
power: supply: cpcap-charger: Improve battery detection
power: supply: cpcap-battery: Check voltage before orderly_poweroff
power: supply: cpcap-charger: Limit voltage to 4.2V for battery
power: supply: ab8500: Handle invalid IRQ from platform_get_irq_byname()
power: supply: ab8500_fg: Do not free non-requested IRQs in probe's error path
power: supply: ab8500: Cleanup probe in reverse order
power: reset: at91: fix __le32 cast in reset code
power: supply: abx500_chargalg: Fix code indentation
mfd: Switch the AB8500 GPADC to IIO
iio: adc: New driver for the AB8500 GPADC
...
There is no need to cast a typed pointer to a void pointer when calling
a function that accepts the latter. Remove it, as the cast prevents
further compiler checks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The bd70528 charger driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell for
charger is added.
Fixes: f8c7f7ddd8 ("power: supply: Initial support for ROHM BD70528 PMIC charger block")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix inconsistent IS_ERR and PTR_ERR in ab8500_charger_probe().
The proper pointer to be passed as argument is di->adc_main_charger_c
This bug was detected with the help of Coccinelle.
Fixes: 97ab78bac5 ("power: supply: ab8500_charger: Convert to IIO ADC")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
add poweroff driver for mt6323 and make Makefile and Kconfig-Entries
Suggested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Josef Friedl <josef.friedl@speed.at>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add 'static' keyword to internal function as reported by sparse
using the following configuration:
make ARCH=x86_64 allmodconfig
make C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__'
Fixes: d4ee021c41 ("power: supply: cpcap-charger: Limit voltage to 4.2V for battery")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds support for the coulomb counter calibration on init. We do
this by polling for now, and only add partial calibration done interrupt
support.
Then later on when we know for sure we have the calibration done interrupt
available in the device tree, we can switch to using the calibration done
interrupt.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We can simplify code in the later patches by reading and saving the
integrator register CCI. Let's also fix a comment typo for register range
naming while at it.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We can use sign_extend32() here to simplify things. And let's fix the
comment for CCM register, that contains the calibration offset.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We can simplify cpcap_battery_cc_raw_div() with div_s64.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We can simplify cpcap_battery_cc_raw_div() a bit by moving the units per
lsb to ddata.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Let's allow reconfiguring the cpcap-charger max charge voltage and
default to 4.2V that should be safe for the known users.
This allows the users to use 4.35V for the extra capacity if really
needed at a cost of probably shorter battery life. We check the
constant charge voltage limit set by the battery.
Some pieces of the property setting code is based on an earlier patch
from Pavel Machek <pavel@ucw.cz> but limited to configuring the charge
voltage for now.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
With cpcap-charger now using 4.2V instead of 4.35V, we never reach
POWER_SUPPLY_CAPACITY_LEVEL_FULL unless we handle the lowered charge
voltage.
Let's do this by implementing POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
and assume anything at that level or higher is a full battery.
Let's also make it configurable for users who may still want to
reconfigure it, and notify the charger if supported by the charger.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We are currently using a wrong ADC range for the battery detection.
The ADC returns the battery temperature if connected.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We can get the low voltage interrupt trigger sometimes way too early,
maybe because of CPU load spikes. This causes orderly_poweroff() be
called too easily.
Let's check the voltage before orderly_poweroff in case it was not
yet a permanent condition. We will be getting more interrupts anyways
if the condition persists.
Let's also show the measured voltages for low battery and battery
empty warnings since we have them.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This immutable branch contains CPCAP charger changes, which
touch ARM and power-supply subsystem.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Nbmd
-----END PGP SIGNATURE-----
Merge tag 'psy-cpcap-charge-volt-limit-signed' into psy-next
Immutable branch between arm and power-supply for cpcap-charger
This immutable branch contains CPCAP charger changes, which
touch ARM and power-supply subsystem.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
There have been some cases of droid4 battery bulging that seem to be
related to being left connected to the charger for several weeks.
It is suspected that the 4.35V charge voltage configured for the battery
is too much in the long run, so lets limit the charge voltage to 4.2V.
It could also be that the batteries are just getting old.
We don't really want to just change the charge voltage to 4.2V as Android
may have charged the battery to 4.35V as pointed out by Pavel Machek.
To add checks for battery voltage, the driver needs to understand the
voltage it's charging at, and also needs to better understand it's
charger state. Right now it only understands connect and disconnect,
while now we need to know also a connected state but not charging.
So let's add better charger state handling with help of chrgcurr2 interrupt
for detecting charge full and retry, and add a check for battery voltage
before we start charging. And then we finally can lower the charge voltage
to 4.2V.
Note that we've been using the same register values as the Android distros
on droid4, so it is suspected that the same problem also exists in Android.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
platform_get_irq_byname() might return -errno which later would be
cast to an unsigned int and used in request_irq().
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When requesting interrupt fails, free only interrupts already requested,
not all of them.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
It is logical to cleanup in probe's error path in reverse order to
previous actions. It also makes easier to add additional goto labels
within this error path.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Merge immutable branch from IIO subsystem for driver
changes in ab8500_btemp, ab8500_charger and ab8500_fg.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The writel() takes standard integers, not __le32 so
fix the following sparse warnings by removing the
cpu_to_le32() calls.
drivers/power/reset/at91-reset.c:134:9: warning: cast from restricted __le32
drivers/power/reset/at91-reset.c:143:9: warning: cast from restricted __le32
This has made no code changes, the md5sums pre and post applying
this patch are the same. The at91 should be natively little endian
anyway.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixed Code indentation error caused due to using spaces
instead of tabs.
The error reported by checkpatch.pl is:
ERROR: code indent should use tabs where possible
The warning reported by checkpatch.pl is:
WARNING: please, no spaces at the start of a line
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik04@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This switches the AB8500 fuel gauge driver to using
the standard IIO ADC channel lookup and conversion routines.
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This switches the AB8500 battery charger driver to using
the standard IIO ADC channel lookup and conversion routines.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This switches the AB8500 battery temperature driver to using
the standard IIO ADC channel lookup and conversion routines.
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AXP813 PMIC has support for detection of USB Battery Charging
specification, and it will limit the current to 500mA by default when
the detection is not enabled or the detection result is SDP.
Enable the BC detection to allow correctly selection of the current.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Driver has been enabled also for SAM9X60. At the moment the patch which did
this has been sent to mainline the PMC for SAM9X60 wasn't integrated.
SAM9X60 has a new PMC compatible (see commit 01e2113de9
("clk: at91: add sam9x60 pmc driver")). Do to this we have to
look for proper PMC compatible here, in SHDWC driver.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
CURRENT is really general in other battery drivers,
Android also has an interface to monitor CURRENT, so let's
add it into test framework.
The default value (1.6A) is just a random but reasonable value.
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
CHARGE_COUNTER is really general in other power supply drivers and
Android also has an interface to monitor CHARGE_COUNTER, so let's
add it into test framework.
Set default as -1000 is because the default status is
POWER_SUPPLY_STATUS_DISCHARGING, which means the counter should be
negative, and 1000 means not zero but small enough.
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Core:
* Ensure HWMON devices are registered with valid names
* Fix device wakeup code
Drivers:
* bq25890_charger: Add BQ25895 support
* axp288_fuel_gauge: Add Minix Neo Z83-4 to blacklist
* sc27xx: improve battery calibration
* misc. small fixes all over drivers
-----BEGIN PGP SIGNATURE-----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=cIXy
-----END PGP SIGNATURE-----
Merge tag 'for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Ensure HWMON devices are registered with valid names
- Fix device wakeup code
Drivers:
- bq25890_charger: Add BQ25895 support
- axp288_fuel_gauge: Add Minix Neo Z83-4 to blacklist
- sc27xx: improve battery calibration
- misc small fixes all over drivers"
* tag 'for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (24 commits)
power: supply: cpcap-charger: Enable vbus boost voltage
power: supply: sc27xx: Add POWER_SUPPLY_PROP_CALIBRATE attribute
power: supply: sc27xx: Optimize the battery capacity calibration
power: supply: sc27xx: Make sure the alarm capacity is larger than 0
power: supply: sc27xx: Fix the the accuracy issue of coulomb calculation
power: supply: sc27xx: Fix conditon to enable the FGU interrupt
power: supply: sc27xx: Add POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN attribute
power: supply: max77650: add MODULE_ALIAS()
power: supply: isp1704: remove redundant assignment to variable ret
power: supply: bq25890_charger: Add the BQ25895 part
power: supply: sc27xx: Replace devm_add_action() followed by failure action with devm_add_action_or_reset()
power: supply: sc27xx: Introduce local variable 'struct device *dev'
power: reset: reboot-mode: Fix author email format
power: supply: ab8500: remove set but not used variables 'vbup33_vrtcn' and 'bup_vch_range'
power: supply: max17042_battery: Fix a typo in function names
power: reset: gpio-restart: Fix typo when gpio reset is not found
power: supply: Init device wakeup after device_add()
power: supply: ab8500_charger: Mark expected switch fall-through
power: supply: sbs-battery: only return health when battery present
MAINTAINERS: N900: Remove isp1704_charger.h record
...
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
We are currently not enabling VBUS boost for cpcap when in host mode.
This means the VBUS is fed at the battery voltage level, which can cause
flakeyness enumerating devices.
Looks like the boost control for VBUS is CPCAP_BIT_VBUS_SWITCH that we
must enable in the charger for nice 4.92 V VBUS output. And looks like
we must not use the STBY pin enabling but must instead use manual VBUS
control in phy-cpcap-usb.
We want to do this in cpcap_charger_vbus_work() and also set a flag for
feeding_vbus to avoid races between USB detection and charger detection,
and disable charging if feeding_vbus is set.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add the 'POWER_SUPPLY_PROP_CALIBRATE' attribute to allow chareger manager
to calibrate the battery capacity.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch factors out the capacity calibration into one single function
to calibrate the battery capacity, and adding more abnormal cases to
calibrate the capacity when the OCV value is not matchable with current
capacity.
Moreover we also allow to calibrate the capacity when charger magager
tries to get current capacity to make sure we give a correct capacity
for userspace.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We must make sure the alarm capacity is larger than 0, to help to
calibrate the low battery capacity.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Spreadtrum fuel gauge will multiply by 2 for counting the coulomb
counter to improve the accuracy, which means the value saved in fuel
gauge is: coulomb counter * 2 * 1000ma_adc. Thus fix the conversion
formular to improve the accuracy of calculating the battery capacity.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We should allow to enable FGU interrupt to adjust the battery capacity,
when charging status is POWER_SUPPLY_STATUS_DISCHARGING.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN attribute to provide the battery's
design capacity for charger manager to calculate the charging counter.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Define a MODULE_ALIAS() in the charger sub-driver for max77650 so that
the appropriate module gets loaded together with the core mfd driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The variable ret is being assigned with a value that is never
read and it is being updated later with a new value. The
assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The BQ25895 is almost identical to the BQ25890.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce local variable 'struct device *dev' and use it instead of
dereferencing it repeatly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Closing angle bracket was missing.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/power/supply/ab8500_charger.c:
In function ab8500_charger_init_hw_registers:
drivers/power/supply/ab8500_charger.c:3013:24: warning:
variable vbup33_vrtcn set but not used [-Wunused-but-set-variable]
drivers/power/supply/ab8500_charger.c:3013:5: warning:
variable bup_vch_range set but not used [-Wunused-but-set-variable]
Fixes: 4c4268dc97 ("power: supply: ab8500: Drop AB8540/9540 support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
It is likely that 'max10742_[un]lock_model()' functions should be
'max17042_[un]lock_model()'
(0 and 7 switched in 10742)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is a bit of mess between cros-ec mfd includes and platform
includes. For example, we have a linux/mfd/cros_ec.h include that
exports the interface implemented in platform/chrome/cros_ec_proto.c. Or
we have a linux/mfd/cros_ec_commands.h file that is non related to the
multifunction device (in the sense that is not exporting any function of
the mfd device). This causes crossed includes between mfd and
platform/chrome subsystems and makes the code difficult to read, apart
from creating 'curious' situations where a platform/chrome driver includes
a linux/mfd/cros_ec.h file just to get the exported functions that are
implemented in another platform/chrome driver.
In order to have a better separation on what the cros-ec multifunction
driver does and what the cros-ec core provides move and rework the
affected includes doing:
- Move cros_ec_commands.h to include/linux/platform_data/cros_ec_commands.h
- Get rid of the parts that are implemented in the platform/chrome/cros_ec_proto.c
driver from include/linux/mfd/cros_ec.h to a new file
include/linux/platform_data/cros_ec_proto.h
- Update all the drivers with the new includes, so
- Drivers that only need to know about the protocol include
- linux/platform_data/cros_ec_proto.h
- linux/platform_data/cros_ec_commands.h
- Drivers that need to know about the cros-ec mfd device also include
- linux/mfd/cros_ec.h
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Series changes: 3
- Fix dereferencing pointer to incomplete type 'struct cros_ec_dev' (lkp)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, the ChromeOS EC core driver has nothing related to an MFD device, so
move that driver from the MFD subsystem to the platform/chrome subsystem.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We may want to use the device pointer in device_init_wakeup() with
functions that expect the device to already be added with device_add().
For example, if we were to link the device initializing wakeup to
something in sysfs such as a class for wakeups we'll run into an error.
It looks like this code was written with the assumption that the device
would be added before initializing wakeup due to the order of operations
in power_supply_unregister().
Let's change the order of operations so we don't run into problems here.
Fixes: 948dcf9662 ("power_supply: Prevent suspend until power supply events are processed")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tri Vo <trong@android.com>
Cc: Kalesh Singh <kaleshsingh@google.com>
Cc: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: allmodconfig arm):
drivers/power/supply/ab8500_charger.c:738:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
when the battery is set to sbs-mode and no gpio detection is enabled
"health" is always returning a value even when the battery is not present.
All other fields return "not present".
This leads to a scenario where the driver is constantly switching between
"present" and "not present" state. This generates a lot of constant
traffic on the i2c.
This commit changes the response of "health" to an error when the battery
is not responding leading to a consistent "not present" state.
Fixes: 76b16f4cdf ("power: supply: sbs-battery: don't assume MANUFACTURER_DATA formats")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Nosthoff <committed@heine.so>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
the type flag is stored in the chip->flags field not in the
client->flags field. This currently leads to never using the ti
specific health function as client->flags doesn't use that bit.
So it's always falling back to the general one.
Fixes: 76b16f4cdf ("power: supply: sbs-battery: don't assume MANUFACTURER_DATA formats")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Nosthoff <committed@heine.so>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Minix Neo Z83-4 is another mini PC using the AXP288 PMIC where the
EFI code does not disable the charger part of the PMIC causing us to report
battery readings (of always 100%) to userspace even though there is no
battery in this wall-outlet powered device.
Add it to the blacklist to avoid the bogus battery status reporting.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The blacklist is getting big enough that it is good to have some sort
of fixed order for it, sort it alphabetically.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
With the introduction of the HWMON compatibility layer to the power
supply framework in Linux 5.3, all power supply devices' names can be
used directly to create HWMON devices with the same names.
But HWMON has rules on allowable names that are different from those
used in the power supply framework. The dash character is forbidden, as
it is used by the libsensors library in userspace as a separator,
whereas this character is used in the device names in more than half of
the existing power supply drivers. This last case is consistent with the
typical naming usage with MFD and Device Tree.
This leads to warnings in the kernel log, with the format:
power_supply gpio-charger: hwmon: \
'gpio-charger' is not a valid name attribute, please fix
Add a protection to power_supply_add_hwmon_sysfs() that replaces any
dash in the device name with an underscore when registering with the
HWMON framework. Other forbidden characters (star, slash, space, tab,
newline) are not replaced, as they are not in common use.
Fixes: e67d4dfc9f ("power: supply: Add HWMON compatibility layer")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: allmodconfig arm):
drivers/power/supply/ab8500_charger.c: In function ‘ab8500_charger_max_usb_curr’:
drivers/power/supply/ab8500_charger.c:738:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (di->vbus_detected) {
^
drivers/power/supply/ab8500_charger.c:745:2: note: here
case USB_STAT_HM_IDGND:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
It has been replaced with the more mature ingenic-battery driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Core:
* Add HWMON compat layer
* New properties
- input power limit
- input voltage limit
Drivers:
* qcom-pon: add gen2 support
* New driver for storing reboot move in NVMEM
* New driver for Wilco EC charger configuration
* simplify getting the adapter of a client
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE72YNB0Y/i3JqeVQT2O7X88g7+poFAl0s0xgACgkQ2O7X88g7
+pqxFQ/9GmfgHpzZ+qQmpBR5zyw1+yrhls3BXYEgHtGM+3YZ6n1sF8Yl1eUYpviC
ldvN3vHXaxRlG5eDBwMl3ScWZnaxMpZssigO3lL4o+kYng0c0xqaPZZYxA9oJNgn
0ertZrYcQZWmT82aRnjt2/p+8n+Hld6bv89PodWdLvsDvId1qQPXu5ILV0JL/QNK
FMQepuaiRu9VXlyPCuWYwoOmKruZjLF7SOyis+I4e55U7lHeyCOySH/tZTTFgd+n
hUpWm4ekc7YCAJVVJUQcdBtfNvQm1KtGkLSnSockH/636kP2fh5ESj76z8i5I6/6
yl7OrkCyhespqS9hGCKCPU95s8MQe8HurlGR8aIWHLJJMiv1hIVOq7n9Uj+mmdRS
OkKQHo/RUxXn5ioCUF3F3NcB94/95f0AWrx3RXjeXd2kYlUmVKCHyaGjPT9WfSOe
MUcLZwM+GsG+3SWBhPGqjuIhIGfBBuQk+mcYLPLP/j3emNeLByYEtEDhvoQbEooU
TCyJGR+FGIAyjXcW/uZzxx8MiZPybSXo7a4j837Cx6sRNwZJ4V9Ve/7XdUy7DKD0
kOBH/ndJhoKJQkup+HEGmv/8os4K8gyW/kaiu718mS0oLDfQGDy0C0Y8BNoJnw4k
/jo/1q0KY+8Hd6bxqbommA2ORAw7XsDZB7eWWC4gDqMXVcF1S6k=
=fmGg
-----END PGP SIGNATURE-----
Merge tag 'for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- add HWMON compat layer
- new properties:
- input power limit
- input voltage limit
Drivers:
- qcom-pon: add gen2 support
- new driver for storing reboot move in NVMEM
- new driver for Wilco EC charger configuration
- simplify getting the adapter of a client"
* tag 'for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: reset: nvmem-reboot-mode: add CONFIG_OF dependency
power_supply: wilco_ec: Add charging config driver
power: supply: cros: allow to set input voltage and current limit
power: supply: add input power and voltage limit properties
power: supply: fix semicolon.cocci warnings
power: reset: nvmem-reboot-mode: use NVMEM as reboot mode write interface
dt-bindings: power: reset: add document for NVMEM based reboot-mode
reset: qcom-pon: Add support for gen2 pon
dt-bindings: power: reset: qcom: Add qcom,pm8998-pon compatibility line
power: supply: Add HWMON compatibility layer
power: supply: sbs-manager: simplify getting the adapter of a client
power: supply: rt9455_charger: simplify getting the adapter of a client
power: supply: rt5033_battery: simplify getting the adapter of a client
power: supply: max17042_battery: simplify getting the adapter of a client
power: supply: max17040_battery: simplify getting the adapter of a client
power: supply: max14656_charger_detector: simplify getting the adapter of a client
power: supply: bq25890_charger: simplify getting the adapter of a client
power: supply: bq24257_charger: simplify getting the adapter of a client
power: supply: bq24190_charger: simplify getting the adapter of a client
- Set 'struct device' fwnode when registering a new device
- New Drivers
- Add support for ROHM BD70528 PMIC
- New Device Support
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
- New Functionality
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
- Fix-ups
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
- Bug Fixes
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera
-----BEGIN PGP SIGNATURE-----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=A3jw
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Set 'struct device' fwnode when registering a new device
New Drivers:
- Add support for ROHM BD70528 PMIC
New Device Support:
- Add support for LP87561 4-Phase Regulator to TI LP87565 PMIC
- Add support for RK809 and RK817 to Rockchip RK808
- Add support for Lid Angle to ChromeOS core
- Add support for CS47L15 CODEC to Madera core
- Add support for CS47L92 CODEC to Madera core
- Add support for ChromeOS (legacy) Accelerometers in ChromeOS core
- Add support for Add Intel Elkhart Lake PCH to Intel LPSS
New Functionality:
- Provide regulator supply information when registering; madera-core
- Additional Device Tree support; lp87565, madera, cros-ec, rohm,bd71837-pmic
- Allow over-riding power button press via Device Tree; rohm-bd718x7
- Differentiate between running processors; cros_ec_dev
Fix-ups:
- Big header file update; cros_ec_commands.h
- Split header per-subsystem; rohm-bd718x7
- Remove superfluous code; menelaus, cs5535-mfd, cs47lXX-tables
- Trivial; sorting, coding style; intel-lpss-pci
- Only remove Power Off functionality if set locally; rk808
- Make use for Power Off Prepare(); rk808
- Fix spelling mistake in header guards; stmfx
- Properly free IDA resources
- SPDX fixups; cs47lXX-tables, madera
- Error path fixups; hi655x-pmic
Bug Fixes:
- Add missing break in case() statement
- Repair undefined behaviour when not initialising variables; arizona-core, madera-core
- Fix reference to Device Tree documentation; madera"
* tag 'mfd-next-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: hi655x-pmic: Fix missing return value check for devm_regmap_init_mmio_clk
mfd: madera: Fixup SPDX headers
mfd: madera: Remove some unused registers and fix some defaults
mfd: intel-lpss: Release IDA resources
mfd: intel-lpss: Add Intel Elkhart Lake PCH PCI IDs
mfd: cs5535-mfd: Remove ifdef OLPC noise
mfd: stmfx: Fix macro definition spelling
dt-bindings: mfd: Add link to ROHM BD71847 Datasheet
MAINAINERS: Swap words in INTEL PMIC MULTIFUNCTION DEVICE DRIVERS
mfd: cros_ec_dev: Register cros_ec_accel_legacy driver as a subdevice
mfd: rk808: Prepare rk805 for poweroff
mfd: rk808: Check pm_power_off pointer
mfd: cros_ec: differentiate SCP from EC by feature bit
dt-bindings: Add binding for cros-ec-rpmsg
mfd: madera: Add Madera core support for CS47L92
mfd: madera: Add Madera core support for CS47L15
mfd: madera: Update DT bindings to add additional CODECs
mfd: madera: Add supply mapping for MICVDD
mfd: madera: Fix potential uninitialised use of variable
mfd: madera: Fix bad reference to pinctrl.txt file
...
ASUS WMI driver got a big refactoring in order to support the TUF Gaming
laptops. Besides that, the regression with backlight being permanently off
on various EeePC laptops has been fixed.
Accelerometer on HP ProBook 450 G0 shows wrong measurements due to
X axis being inverted. This has been fixed.
Intel PMC core driver has been extended to be ACPI enumerated
if the DSDT provides device with _HID "INT33A1". This allows
to convert the driver to be pure platform and support new hardware
purely based on ACPI DSDT.
From now on the Intel Speed Select Technology is supported thru
a corresponding driver. This driver provides an access to the features
of the ISST, such as Performance Profile, Core Power, Base frequency and
Turbo Frequency.
Mellanox platform drivers has been refactored and now extended
to support more systems, including new coming ones.
The OLPC XO-1.75 platform is now supported.
CB4063 Beckhoff Automation board is using PMC clocks,
provided via pmc_atom driver, for ethernet controllers in a way
that they can't be managed by the clock driver. The quirk
has been extended to cover this case.
Touchscreen on Chuwi Hi10 Plus tablet has been enabled. Meanwhile
the information of Chuwi Hi10 Air has been fixed to cover more models
based on the same platform.
Xiaomi notebooks have WMI interface enabled. Thus, the driver to support it
has been provided. It required some extension of the generic WMI library,
which allows to propagate opaque context to the ->probe() of the
individual drivers.
This release includes debugfs clean up from Greg KH for several drivers
that drop return code check and make debugfs absence or failure non-fatal.
Miscellaneous fixes here and there, mostly for Acer WMI and
various Intel drivers.
The listed below commits are duplicated due to previously pushed fixes in v5.2 cycle:
- 1dd93f873d platform/x86: asus-wmi: Only Tell EC the OS will handle display hotkeys from asus_nb_wmi
- 89ae3a0736 platform/x86: intel-vbtn: Report switch events when event wakes device
- fa882fc80d platform/x86: mlx-platform: Fix parent device in i2c-mux-reg device registration
- 0bfcd24b39 platform/mellanox: mlxreg-hotplug: Add devm_free_irq call to remove flow
The following is an automated git shortlog grouped by driver:
acer-wmi:
- Mark expected switch fall-throughs
- no need to check return value of debugfs_create functions
asus-nb-wmi:
- Add microphone mute key code
asus-wmi:
- Use dev_get_drvdata()
- Do not disable keyboard backlight on unloading
- Switch fan boost mode
- Enhance detection of thermal data
- Organize code into sections
- Refactor error handling
- Support WMI event queue
- Refactor WMI event handling
- Improve DSTS WMI method ID detection
- Increase input buffer size of WMI methods
- Fix preserving keyboard backlight intensity on load
- Fix hwmon device cleanup
- no need to check return value of debugfs_create functions
- Only Tell EC the OS will handle display hotkeys from asus_nb_wmi
dell-laptop:
- no need to check return value of debugfs_create functions
hp_accel:
- Add support for HP ProBook 450 G0
ideapad-laptop:
- no need to check return value of debugfs_create functions
intel_int0002_vgpio:
- Get rid of custom ICPU() macro
intel_menlow:
- avoid null pointer deference error
intel_pmc:
- no need to check return value of debugfs_create functions
intel_pmc_core:
- Attach using APCI HID "INT33A1"
- transform Pkg C-state residency from TSC ticks into microseconds
intel_telemetry:
- no need to check return value of debugfs_create functions
intel-vbtn:
- Report switch events when event wakes device
ISST:
- Restore state on resume
- Add Intel Speed Select PUNIT MSR interface
- Add Intel Speed Select mailbox interface via MSRs
- Add Intel Speed Select mailbox interface via PCI
- Add Intel Speed Select mmio interface
- Add IOCTL to Translate Linux logical CPU to PUNIT CPU number
- Store per CPU information
- Add common API to register and handle ioctls
- Update ioctl-number.txt for Intel Speed Select interface
- A tool to validate Intel Speed Select commands
- Add .gitignore file
MAINTAINERS:
- Update for Intel Speed Select Technology
mlx-platform:
- Fix error handling in mlxplat_init()
- Add more reset cause attributes
- Modify DMI matching order
- Add regmap structure for the next generation systems
- Change API for i2c-mlxcpld driver activation
- Move regmap initialization before all drivers activation
- Fix parent device in i2c-mux-reg device registration
- Add new attribute for mlxreg-io sysfs interfaces
pcengines-apuv2:
- Make two symbols static
- Fix PCENGINES_APU2 Kconfig warning
OLPC:
- Add a config menu category for XO 1.75
- Require CONFIG_POWER_SUPPLY for XO-1.75 EC
- Fix olpc_xo175_ec_cmd() return value
- Make olpc_dt_compatible_match() static __init
- Add INPUT dependencies
- Fix build error without CONFIG_SPI
- Add a regulator for the DCON
- Add XO-1.75 EC driver
- Use BIT() and GENMASK() for event masks
- Avoid a warning if the EC didn't register yet
- Move EC-specific functionality out from x86
- Remove an unused include
- Add OLPC XO-1.75 EC bindings
platform/mellanox:
- mlxreg-hotplug: Add devm_free_irq call to remove flow
pmc_atom:
- Add CB4063 Beckhoff Automation board to critclk_systems DMI table
- no need to check return value of debugfs_create functions
Kconfig:
- Remove left-over BACKLIGHT_LCD_SUPPORT
samsung-laptop:
- no need to check return value of debugfs_create functions
touchscreen_dmi:
- Update Hi10 Air filter
- Add info for the CHUWI Hi10 Plus tablet.
wmi:
- add Xiaomi WMI key driver
- add context argument to the probe function
- add context pointer field to struct wmi_device_id
- Add function to get _UID of WMI device
-----BEGIN PGP SIGNATURE-----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=DC5j
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.3-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
"Gathered a bunch of x86 platform driver changes. It's rather big,
since includes two big refactors and completely new driver:
- ASUS WMI driver got a big refactoring in order to support the TUF
Gaming laptops. Besides that, the regression with backlight being
permanently off on various EeePC laptops has been fixed.
- Accelerometer on HP ProBook 450 G0 shows wrong measurements due to
X axis being inverted. This has been fixed.
- Intel PMC core driver has been extended to be ACPI enumerated if
the DSDT provides device with _HID "INT33A1". This allows to
convert the driver to be pure platform and support new hardware
purely based on ACPI DSDT.
- From now on the Intel Speed Select Technology is supported thru a
corresponding driver. This driver provides an access to the
features of the ISST, such as Performance Profile, Core Power, Base
frequency and Turbo Frequency.
- Mellanox platform drivers has been refactored and now extended to
support more systems, including new coming ones.
- The OLPC XO-1.75 platform is now supported.
- CB4063 Beckhoff Automation board is using PMC clocks, provided via
pmc_atom driver, for ethernet controllers in a way that they can't
be managed by the clock driver. The quirk has been extended to
cover this case.
- Touchscreen on Chuwi Hi10 Plus tablet has been enabled. Meanwhile
the information of Chuwi Hi10 Air has been fixed to cover more
models based on the same platform.
- Xiaomi notebooks have WMI interface enabled. Thus, the driver to
support it has been provided. It required some extension of the
generic WMI library, which allows to propagate opaque context to
the ->probe() of the individual drivers.
This release includes debugfs clean up from Greg KH for several
drivers that drop return code check and make debugfs absence or
failure non-fatal.
Also miscellaneous fixes here and there, mostly for Acer WMI and
various Intel drivers"
* tag 'platform-drivers-x86-v5.3-1' of git://git.infradead.org/linux-platform-drivers-x86: (74 commits)
platform/x86: Fix PCENGINES_APU2 Kconfig warning
tools/power/x86/intel-speed-select: Add .gitignore file
platform/x86: mlx-platform: Fix error handling in mlxplat_init()
platform/x86: intel_pmc_core: Attach using APCI HID "INT33A1"
platform/x86: intel_pmc_core: transform Pkg C-state residency from TSC ticks into microseconds
platform/x86: asus-wmi: Use dev_get_drvdata()
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform/x86: mlx-platform: Add more reset cause attributes
platform/x86: mlx-platform: Modify DMI matching order
platform/x86: mlx-platform: Add regmap structure for the next generation systems
platform/x86: mlx-platform: Change API for i2c-mlxcpld driver activation
platform/x86: mlx-platform: Move regmap initialization before all drivers activation
MAINTAINERS: Update for Intel Speed Select Technology
tools/power/x86: A tool to validate Intel Speed Select commands
platform/x86: ISST: Restore state on resume
platform/x86: ISST: Add Intel Speed Select PUNIT MSR interface
platform/x86: ISST: Add Intel Speed Select mailbox interface via MSRs
platform/x86: ISST: Add Intel Speed Select mailbox interface via PCI
platform/x86: ISST: Add Intel Speed Select mmio interface
platform/x86: ISST: Add IOCTL to Translate Linux logical CPU to PUNIT CPU number
...
Without CONFIG_OF, we get a build failure in the reboot-mode
implementation:
drivers/power/reset/reboot-mode.c: In function 'reboot_mode_register':
drivers/power/reset/reboot-mode.c:72:2: error: implicit declaration of function 'for_each_property_of_node'; did you mean 'for_each_child_of_node'? [-Werror=implicit-function-declaration]
for_each_property_of_node(np, prop) {
Add a Kconfig dependency like we have for the other users of
CONFIG_REBOOT_MODE.
Fixes: 7a78a7f769 ("power: reset: nvmem-reboot-mode: use NVMEM as reboot mode write interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
* pm-opp:
opp: Don't use IS_ERR on invalid supplies
opp: Make dev_pm_opp_set_rate() handle freq = 0 to drop performance votes
opp: Don't overwrite rounded clk rate
opp: Allocate genpd_virt_devs from dev_pm_opp_attach_genpd()
opp: Attach genpds to devices from within OPP core
* pm-misc:
PM / clk: Remove error message on out-of-memory condition
drivers: base: power: clock_ops: Use of_clk_get_parent_count()
* pm-avs:
power: avs: smartreflex: no need to check return value of debugfs_create functions
* pm-tools:
cpupower : frequency-set -r option misses the last cpu in related cpu list
cpupower: correct spelling of interval
Add README and update pm-graph and sleepgraph docs
Update to pm-graph 5.4
Update to pm-graph 5.3
Add a driver to control the charging algorithm used on Wilco
devices. See Documentation/ABI/testing/sysfs-class-power-wilco
for the userspace interface and other info.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch allows reading and writing the input voltage and current
limit through the POWER_SUPPLY_PROP_INPUT_VOLTAGE_LIMIT and
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT sysfs properties. This allows
userspace to see current values and to re-configure these values at
runtime based on system-level knowledge or user input.
By default there is no limit, this is reported as a -1 when reading from
userspace. Writing a value will set the current or voltage limit in uA
or uV, and writing any negative value will remove that limit.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
For thermal management strategy you might be interested on limit the
input power for a power supply. We already have current limit but
basically what we probably want is to limit power. So, introduce the
input_power_limit property.
Although the common use case is limit the input power, in some
specific cases it is the voltage that is problematic (i.e some regulators
have different efficiencies at higher voltage resulting in more heat).
So introduce also the input_voltage_limit property.
This happens in one Chromebook and is used on the Pixel C's thermal
management strategy to effectively limit the input power to 5V 3A when
the screen is on. When the screen is on, the display, the CPU, and the GPU
all contribute more heat to the system than while the screen is off, and
we made a tradeoff to throttle the charger in order to give more of the
thermal budget to those other components.
So there's nothing fundamentally broken about the hardware that would
cause the Pixel C to malfunction if we were charging at 9V or 12V instead
of 5V when the screen is on, i.e. if userspace doesn't change this.
What would happen is that you wouldn't meet Google's skin temperature
targets on the system if the charger was allowed to run at 9V or 12V with
the screen on.
For folks hacking on Pixel Cs (which is now outside of Google's official
support window for Android) and customizing their own kernel and userspace
this would be acceptable, but we wanted to expose this feature in the
power supply properties because the feature does exist in the Emedded
Controller firmware of the Pixel C and all of Google's Chromebooks with
USB-C made since 2015 in case someone running an up to date kernel wanted
to limit the charging power for thermal or other reasons.
This patch exposes a new property, similar to input current limit, to
re-configure the maximum voltage from the external supply at runtime
based on system-level knowledge or user input.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
ROHM BD70528 PMIC includes battery charger block. Support charger
staus queries and doing few basic settings like input current limit
and charging current.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Claudiu.Beznea@microchip.com