Netlink support of extended packet number cipher suites,
allows adding and updating XPN macsec interfaces.
Added support in:
* Creating interfaces with GCM-AES-XPN-128 and GCM-AES-XPN-256 suites.
* Setting and getting 64bit packet numbers with of SAs.
* Setting (only on SA creation) and getting ssci of SAs.
* Setting salt when installing a SAK.
Added 2 cipher suite identifiers according to 802.1AE-2018 table 14-1:
* MACSEC_CIPHER_ID_GCM_AES_XPN_128
* MACSEC_CIPHER_ID_GCM_AES_XPN_256
In addition, added 2 new netlink attribute types:
* MACSEC_SA_ATTR_SSCI
* MACSEC_SA_ATTR_SALT
Depends on: macsec: Support XPN frame handling - IEEE 802.1AEbw.
Signed-off-by: Era Mayflower <mayflowerera@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support extended packet number cipher suites (802.1AEbw) frames handling.
This does not include the needed netlink patches.
* Added xpn boolean field to `struct macsec_secy`.
* Added ssci field to `struct_macsec_tx_sa` (802.1AE figure 10-5).
* Added ssci field to `struct_macsec_rx_sa` (802.1AE figure 10-5).
* Added salt field to `struct macsec_key` (802.1AE 10.7 NOTE 1).
* Created pn_t type for easy access to lower and upper halves.
* Created salt_t type for easy access to the "ssci" and "pn" parts.
* Created `macsec_fill_iv_xpn` function to create IV in XPN mode.
* Support in PN recovery and preliminary replay check in XPN mode.
In addition, according to IEEE 802.1AEbw figure 10-5, the PN of incoming
frame can be 0 when XPN cipher suite is used, so fixed the function
`macsec_validate_skb` to fail on PN=0 only if XPN is off.
Signed-off-by: Era Mayflower <mayflowerera@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Notify the offload engine about MAC address change to reconfigure it
accordingly.
Fixes: 3cf3227a21 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCI should be updated, because it contains MAC in its first 6 octets.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for IFLA_MACSEC_PORT
to the netlink policy.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to call macsec_pn_wrapped from hardware drivers to notify when a
PN rolls over. Some drivers might used an interrupt to implement this.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MACsec offloading to underlying hardware devices is disabled by default
(the software implementation is used). This patch adds support for
changing this setting through the MACsec netlink interface. Many checks
are done when enabling offloading on a given MACsec interface as there
are limitations (it must be supported by the hardware, only a single
interface can be offloaded on a given physical device at a time, rules
can't be moved for now).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the MACsec hardware offloading infrastructure.
The main idea here is to re-use the logic and data structures of the
software MACsec implementation. This allows not to duplicate definitions
and structure storing the same kind of information. It also allows to
use a unified genlink interface for both MACsec implementations (so that
the same userspace tool, `ip macsec`, is used with the same arguments).
The MACsec offloading support cannot be disabled if an interface
supports it at the moment.
The MACsec configuration is passed to device drivers supporting it
through macsec_ops which are called from the MACsec genl helpers. Those
functions call the macsec ops of PHY and Ethernet drivers in two steps:
a preparation one, and a commit one. The first step is allowed to fail
and should be used to check if a provided configuration is compatible
with the features provided by a MACsec engine, while the second step is
not allowed to fail and should only be used to enable a given MACsec
configuration. Two extra calls are made: when a virtual MACsec interface
is created and when it is deleted, so that the hardware driver can stay
in sync.
The Rx and TX handlers are modified to take in account the special case
were the MACsec transformation happens in the hardware, whether in a PHY
or in a MAC, as the packets seen by the networking stack on both the
physical and MACsec virtual interface are exactly the same. This leads
to some limitations: the hardware and software implementations can't be
used on the same physical interface, as the policies would be impossible
to fulfill (such as strict validation of the frames). Also only a single
virtual MACsec interface can be offloaded to a physical port supporting
hardware offloading as it would be impossible to guess onto which
interface a given packet should go (for ingress traffic).
Another limitation as of now is that the counters and statistics are not
reported back from the hardware to the software MACsec implementation.
This isn't an issue when using offloaded MACsec transformations, but it
should be added in the future so that the MACsec state can be reported
to the user (which would also improve the debug).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves some structure, type and identifier definitions into a
MACsec specific header. This patch does not modify how the MACsec code
is running and only move things around. This is a preparation for the
future MACsec hardware offloading support, which will re-use those
definitions outside macsec.c.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes variables and callback these are related to the nested
device structure.
devices that can be nested have their own nest_level variable that
represents the depth of nested devices.
In the previous patch, new {lower/upper}_level variables are added and
they replace old private nest_level variable.
So, this patch removes all 'nest_level' variables.
In order to avoid lockdep warning, ->ndo_get_lock_subclass() was added
to get lockdep subclass value, which is actually lower nested depth value.
But now, they use the dynamic lockdep key to avoid lockdep warning instead
of the subclass.
So, this patch removes ->ndo_get_lock_subclass() callback.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a macsec interface is created, it increases a refcnt to a lower
device(real device). when macsec interface is deleted, the refcnt is
decreased in macsec_free_netdev(), which is ->priv_destructor() of
macsec interface.
The problem scenario is this.
When nested macsec interfaces are exiting, the exit routine of the
macsec module makes refcnt leaks.
Test commands:
ip link add dummy0 type dummy
ip link add macsec0 link dummy0 type macsec
ip link add macsec1 link macsec0 type macsec
modprobe -rv macsec
[ 208.629433] unregister_netdevice: waiting for macsec0 to become free. Usage count = 1
Steps of exit routine of macsec module are below.
1. Calls ->dellink() in __rtnl_link_unregister().
2. Checks refcnt and wait refcnt to be 0 if refcnt is not 0 in
netdev_run_todo().
3. Calls ->priv_destruvtor() in netdev_run_todo().
Step2 checks refcnt, but step3 decreases refcnt.
So, step2 waits forever.
This patch makes the macsec module do not hold a refcnt of the lower
device because it already holds a refcnt of the lower device with
netdev_upper_dev_link().
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fei Liu reported a crash when doing netperf on a topo of macsec
dev over veth:
[ 448.919128] refcount_t: underflow; use-after-free.
[ 449.090460] Call trace:
[ 449.092895] refcount_sub_and_test+0xb4/0xc0
[ 449.097155] tcp_wfree+0x2c/0x150
[ 449.100460] ip_rcv+0x1d4/0x3a8
[ 449.103591] __netif_receive_skb_core+0x554/0xae0
[ 449.108282] __netif_receive_skb+0x28/0x78
[ 449.112366] netif_receive_skb_internal+0x54/0x100
[ 449.117144] napi_gro_complete+0x70/0xc0
[ 449.121054] napi_gro_flush+0x6c/0x90
[ 449.124703] napi_complete_done+0x50/0x130
[ 449.128788] gro_cell_poll+0x8c/0xa8
[ 449.132351] net_rx_action+0x16c/0x3f8
[ 449.136088] __do_softirq+0x128/0x320
The issue was caused by skb's true_size changed without its sk's
sk_wmem_alloc increased in tcp/skb_gro_receive(). Later when the
skb is being freed and the skb's truesize is subtracted from its
sk's sk_wmem_alloc in tcp_wfree(), underflow occurs.
macsec is calling gro_cells_receive() to receive a packet, which
actually requires skb->sk to be NULL. However when macsec dev is
over veth, it's possible the skb->sk is still set if the skb was
not unshared or expanded from the peer veth.
ip_rcv() is calling skb_orphan() to drop the skb's sk for tproxy,
but it is too late for macsec's calling gro_cells_receive(). So
fix it by dropping the skb's sk earlier on rx path of macsec.
Fixes: 5491e7c6b1 ("macsec: enable GRO and RPS on macsec devices")
Reported-by: Xiumei Mu <xmu@redhat.com>
Reported-by: Fei Liu <feliu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix use-after-free of skb when rx_handler returns RX_HANDLER_PASS.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
seen with debug config:
drivers/net/macsec.c: In function 'dump_secy':
drivers/net/macsec.c:2597: warning: the frame size of 2216 bytes is larger
than 2048 bytes [-Wframe-larger-than=]
just mark it with noinline_for_stack, this is netlink dump code.
v2: use 'static noinline_for_stack int' consistently
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since maxattr is common, the policy can't really differ sanely,
so make it common as well.
The only user that did in fact manage to make a non-common policy
is taskstats, which has to be really careful about it (since it's
still using a common maxattr!). This is no longer supported, but
we can fake it using pre_doit.
This reduces the size of e.g. nl80211.o (which has lots of commands):
text data bss dec hex filename
398745 14323 2240 415308 6564c net/wireless/nl80211.o (before)
397913 14331 2240 414484 65314 net/wireless/nl80211.o (after)
--------------------------------
-832 +8 0 -824
Which is obviously just 8 bytes for each command, and an added 8
bytes for the new policy pointer. I'm not sure why the ops list is
counted as .text though.
Most of the code transformations were done using the following spatch:
@ops@
identifier OPS;
expression POLICY;
@@
struct genl_ops OPS[] = {
...,
{
- .policy = POLICY,
},
...
};
@@
identifier ops.OPS;
expression ops.POLICY;
identifier fam;
expression M;
@@
struct genl_family fam = {
.ops = OPS,
.maxattr = M,
+ .policy = POLICY,
...
};
This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing
the cb->data as ops, which we want to change in a later genl patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the kernel doesn't let the administrator set a macsec device
up unless its lower device is currently up. This is inconsistent, as a
macsec device that is up won't automatically go down when its lower
device goes down.
Now that linkstate propagation works, there's really no reason for this
limitation, so let's remove it.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Reported-by: Radu Rendec <radu.rendec@gmail.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like all other virtual devices (macvlan, vlan), the operstate of a
macsec device should match the state of its lower device. This is done
by calling netif_stacked_transfer_operstate from its netdevice notifier.
We also need to call netif_stacked_transfer_operstate when a new macsec
device is created, so that its operstate is set properly. This is only
relevant when we try to bring the device up directly when we create it.
Radu Rendec proposed a similar patch, inspired from the 802.1q driver,
that included changing the administrative state of the macsec device,
instead of just the operstate. This version is similar to what the
macvlan driver does, and updates only the operstate.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Reported-by: Radu Rendec <radu.rendec@gmail.com>
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a couple of issues highlighted by checkpatch.pl:
* Missing a blank line after declarations
* Alignment should match open parenthesis
Signed-off-by: Romain Aviolat <r.aviolat@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is just wrong, sorry. I was trying to fix a static checker
warning and misread the code. The reference taken in macsec_newlink()
is released in macsec_free_netdev() when the netdevice is destroyed.
This reverts commit 5dcd840088.
Reported-by: Laura Abbott <labbott@redhat.com>
Fixes: 5dcd840088 ("macsec: missing dev_put() on error in macsec_newlink()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We moved the dev_hold(real_dev); call earlier in the function but forgot
to update the error paths.
Fixes: 0759e552bc ("macsec: fix negative refcnt on parent link")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ccfdec9089 ("macsec: Add support for GCM-AES-256 cipher suite")
changed a few values in the uapi headers for MACsec.
Because of existing userspace implementations, we need to preserve the
value of MACSEC_DEFAULT_CIPHER_ID. Not doing that resulted in
wpa_supplicant segfaults when a secure channel was created using the
default cipher. Thus, swap MACSEC_DEFAULT_CIPHER_{ID,ALT} back to their
original values.
Changing the maximum length of the MACSEC_SA_ATTR_KEY attribute is
unnecessary, as the previous value (MACSEC_MAX_KEY_LEN, which was 128B)
is large enough to carry 32-bytes keys. This patch reverts
MACSEC_MAX_KEY_LEN to 128B and restores the old length check on
MACSEC_SA_ATTR_KEY.
Fixes: ccfdec9089 ("macsec: Add support for GCM-AES-256 cipher suite")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the GCM-AES-256 cipher suite as specified in
IEEE 802.1AEbn-2011. The prepared cipher suite selection mechanism is used,
with GCM-AES-128 being the default cipher suite as defined in the standard.
Signed-off-by: Felix Walter <felix.walter@cloudandheat.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the description, first argument of genlmsg_nlhdr() points to
what genlmsg_put() returns, i.e. beginning of user header. Therefore we
should only subtract size of genetlink header and netlink message header,
not user header.
This also means we don't need to pass the pointer to genetlink family and
the same is true for genl_dump_check_consistent() which is the only caller
of genlmsg_nlhdr(). (Note that at the moment, these functions are only
used for families which do not have user header so that they are not
affected.)
Fixes: 670dc2833d ("netlink: advertise incomplete dumps")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable masces_tx_sa.refcnt is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable masces_rx_sc.refcnt is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable masces_rx_sa.refcnt is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: cda7ea6903 ("macsec: check return value of skb_to_sgvec always")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack arg to netdev_upper_dev_link and netdev_master_upper_dev_link
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helps tools such as wpa_supplicant can start even if the macsec
module isn't loaded yet.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
The macsec implementation shouldn't account for rx/tx packets that are
dropped in the netdev framework. The netdev framework itself accounts
for such packets by atomically updating struct net_device`rx_dropped and
struct net_device`tx_dropped fields. Later on when the stats for macsec
link is retrieved, the packets dropped in netdev framework will be
included in dev_get_stats() after calling macsec.c`macsec_get_stats64()
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We call skb_cow_data, which is good anyway to ensure we can actually
modify the skb as such (another error from prior). Now that we have the
number of fragments required, we can safely allocate exactly that amount
of memory.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While this may appear as a humdrum one line change, it's actually quite
important. An sk_buff stores data in three places:
1. A linear chunk of allocated memory in skb->data. This is the easiest
one to work with, but it precludes using scatterdata since the memory
must be linear.
2. The array skb_shinfo(skb)->frags, which is of maximum length
MAX_SKB_FRAGS. This is nice for scattergather, since these fragments
can point to different pages.
3. skb_shinfo(skb)->frag_list, which is a pointer to another sk_buff,
which in turn can have data in either (1) or (2).
The first two are rather easy to deal with, since they're of a fixed
maximum length, while the third one is not, since there can be
potentially limitless chains of fragments. Fortunately dealing with
frag_list is opt-in for drivers, so drivers don't actually have to deal
with this mess. For whatever reason, macsec decided it wanted pain, and
so it explicitly specified NETIF_F_FRAGLIST.
Because dealing with (1), (2), and (3) is insane, most users of sk_buff
doing any sort of crypto or paging operation calls a convenient function
called skb_to_sgvec (which happens to be recursive if (3) is in use!).
This takes a sk_buff as input, and writes into its output pointer an
array of scattergather list items. Sometimes people like to declare a
fixed size scattergather list on the stack; othertimes people like to
allocate a fixed size scattergather list on the heap. However, if you're
doing it in a fixed-size fashion, you really shouldn't be using
NETIF_F_FRAGLIST too (unless you're also ensuring the sk_buff and its
frag_list children arent't shared and then you check the number of
fragments in total required.)
Macsec specifically does this:
size += sizeof(struct scatterlist) * (MAX_SKB_FRAGS + 1);
tmp = kmalloc(size, GFP_ATOMIC);
*sg = (struct scatterlist *)(tmp + sg_offset);
...
sg_init_table(sg, MAX_SKB_FRAGS + 1);
skb_to_sgvec(skb, sg, 0, skb->len);
Specifying MAX_SKB_FRAGS + 1 is the right answer usually, but not if you're
using NETIF_F_FRAGLIST, in which case the call to skb_to_sgvec will
overflow the heap, and disaster ensues.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: stable@vger.kernel.org
Cc: security@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MACSec test failed when asynchronous crypto operations is used. It
encounters packet validation failed since macsec_skb_cb(skb)->valid
is always 'false'.
This patch adds missing "macsec_skb_cb(skb)->valid = true" in
macsec_decrypt_done() when "err == 0".
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Era Mayflower