struct ipoib_cm_tx is defined at 245th line. And the definition is
independent on the MACRO. The declaration here is unnecessary. Remove it.
Link: https://lore.kernel.org/r/20210415092124.27684-1-wanjiabing@vivo.com
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently IPoIB connected mode queries the device to get the pkey table
entry during connection formation. This will increase the time taken to
form the connection, especially when limited pkeys are in use. This gets
worse when multiple connection attempts are done in parallel.
Since ipoib interfaces are locked to a single pkey, use the pkey index
that was determined at link up time instead of searching for anything.
This improved the latency from 500ms to 1ms on an internal setup.
Link: https://lore.kernel.org/r/1618338965-16717-1-git-send-email-manjunath.b.patil@oracle.com
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When "enhanced IPoIB" is enabled for CX-5 devices it requires the parent
device to be UP, otherwise the child devices won't work.
Thus add a debug message to give admin a hint when only the child
interface is UP but parent interface is not.
Link: https://lore.kernel.org/r/20210408093215.24023-1-jinpu.wang@ionos.com
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Two error messages are only different message but have common
code to generate the path string.
Link: https://lore.kernel.org/r/20210406123639.202899-4-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
It does not help to debug if it only print error message
without any debugging information which session and connection
the error happened.
Link: https://lore.kernel.org/r/20210406123639.202899-3-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Client prints only error value and it is not enough for debugging.
1. When client receives an error from server: the client does not only
print the error value but also more information of server connection.
2. When client failes to send IO: the client gets an error from RDMA
layer. It also print more information of server connection.
Link: https://lore.kernel.org/r/20210406123639.202899-2-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
It shows the latest latency that the client checked when sending the
heart-beat.
Link: https://lore.kernel.org/r/20210407113444.150961-3-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
This patch adds new multipath policy: min-latency. Client checks the
latency of each path when it sends the heart-beat. And it sends IO to the
path with the minimum latency.
Link: https://lore.kernel.org/r/20210407113444.150961-2-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
A session can be removed dynamically by sysfs interface "remove_path" that
eventually calls rtrs_clt_remove_path_from_sysfs function. The current
rtrs_clt_remove_path_from_sysfs first removes the sysfs interfaces and
frees sess->stats object. Second it removes the session from the active
list.
Therefore some functions could access non-connected session and access the
freed sess->stats object even-if they check the session status before
accessing the session.
For instance rtrs_clt_request and get_next_path_min_inflight check the
session status and try to send IO to the session. The session status
could be changed when they are trying to send IO but they could not catch
the change and update the statistics information in sess->stats object,
and generate use-after-free problem.
(see: "RDMA/rtrs-clt: Check state of the rtrs_clt_sess before reading its
stats")
This patch changes the rtrs_clt_remove_path_from_sysfs to remove the
session from the active session list and then destroy the sysfs
interfaces.
Each function still should check the session status because closing or
error recovery paths can change the status.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20210412084002.33582-1-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: db7683d7de ("IB/srpt: Fix login-related race conditions")
Link: https://lore.kernel.org/r/20210408113132.87250-1-wangwensheng4@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The current rdma_netdev handling in ipoib hooks the tx_timeout handler,
but prints out a totally useless message that prevents effective debugging
especially when multiple transmit queues are being used.
Add a tx_timeout rdma_netdev hook and implement the callback in the hfi1
to print additional information.
The existing non-helpful message is avoided when the driver has presented
a callback.
Link: https://lore.kernel.org/r/1617026056-50483-3-git-send-email-dennis.dalessandro@cornelisnetworks.com
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Max io size is limited by both remote buffer size and the max fr pages per
mr.
Link: https://lore.kernel.org/r/20210325153308.1214057-20-gi-oh.kim@ionos.com
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Before receiving the session name, the error message cannot include any
information about which connection generates the error.
This patch stores the addresses of source and target in the sessname field
to show which generates the error. That field will be over-written
when receiving the session name from client.
Link: https://lore.kernel.org/r/20210325153308.1214057-17-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
There is common code converting addresses of source machine and
destination machine to a string. We already have a struct rtrs_addr to
store two addresses. This patch introduces a new function that converts
two addresses into one string with struct rtrs_addr.
Link: https://lore.kernel.org/r/20210325153308.1214057-14-gi-oh.kim@ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Let these cases share the same path since all of them need to close
session.
Link: https://lore.kernel.org/r/20210325153308.1214057-11-gi-oh.kim@ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@ionos.com>
Reviewed-by: Danil Kipnis <danil.kipnis@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The two members are not used in the code, so remove them.
Link: https://lore.kernel.org/r/20210325153308.1214057-10-gi-oh.kim@ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@ionos.com>
Reviewed-by: Danil Kipnis <danil.kipnis@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
We can remove the label after move put_device to the right place.
Link: https://lore.kernel.org/r/20210325153308.1214057-9-gi-oh.kim@ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@ionos.com>
Reviewed-by: Danil Kipnis <danil.kipnis@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
There is no need to dereference 's' from 'sess', since we have "sess =
to_clt_sess(s)" before.
And we can deference 'dev' from 's' earlier.
Link: https://lore.kernel.org/r/20210325153308.1214057-8-gi-oh.kim@ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@ionos.com>
Reviewed-by: Danil Kipnis <danil.kipnis@ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The device is got by isert_device_get() with refcount is 1, and is
assigned to isert_conn by
isert_conn->device = device.
When isert_create_qp() failed, device will be freed with
isert_device_put().
Later, the device is used in isert_free_login_buf(isert_conn) by the
isert_conn->device->ib_device statement.
Free the device in the correct order.
Fixes: ae9ea9ed38 ("iser-target: Split some logic in isert_connect_request to routines")
Link: https://lore.kernel.org/r/20210322161325.7491-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Current code uses many different types when dealing with a port of a RDMA
device: u8, unsigned int and u32. Switch to u32 to clean up the logic.
This allows us to make (at least) the core view consistent and use the
same type. Unfortunately not all places can be converted. Many uverbs
functions expect port to be u8 so keep those places in order not to break
UAPIs. HW/Spec defined values must also not be changed.
With the switch to u32 we now can support devices with more than 255
ports. U32_MAX is reserved to make control logic a bit easier to deal
with. As a device with U32_MAX ports probably isn't going to happen any
time soon this seems like a non issue.
When a device with more than 255 ports is created uverbs will report the
RDMA device as having 255 ports as this is the max currently supported.
The verbs interface is not changed yet because the IBTA spec limits the
port size in too many places to be u8 and all applications that relies in
verbs won't be able to cope with this change. At this stage, we are
extending the interfaces that are using vendor channel solely
Once the limitation is lifted mlx5 in switchdev mode will be able to have
thousands of SFs created by the device. As the only instance of an RDMA
device that reports more than 255 ports will be a representor device and
it exposes itself as a RAW Ethernet only device CM/MAD/IPoIB and other
ULPs aren't effected by this change and their sysfs/interfaces that are
exposes to userspace can remain unchanged.
While here cleanup some alignment issues and remove unneeded sanity
checks (mainly in rdmavt),
Link: https://lore.kernel.org/r/20210301070420.439400-1-leon@kernel.org
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Have the driver use shared CQs which provids a ~10%-20% improvement during
test.
Instead of opening a CQ for each QP per connection, a CQ for each QP will
be provided by the RDMA core driver that will be shared between the QPs on
that core reducing interrupt overhead.
Link: https://lore.kernel.org/r/20210222141551.54345-1-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
tcm_loop could be used like a normal block device, so we can't use
GFP_KERNEL and should use GFP_NOIO. This adds a gfp_t arg to
target_cmd_init_cdb() and converts the users. For every driver but loop
GFP_KERNEL is kept.
This will also be useful in subsequent patches where loop needs to do
target_submit_prep() from interrupt context to get a ref to the se_device,
and so it will need to use GFP_ATOMIC.
Link: https://lore.kernel.org/r/20210227170006.5077-16-michael.christie@oracle.com
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
target_submit_cmd_map_sgls() is being removed, so convert srpt to the new
submission API.
srpt uses target_stop_session() to sync session shutdown with LIO core, so
we use target_init_cmd()/target_submit_prep()/target_submit(), because
target_init_cmd() will detect the target_stop_session() call and return an
error.
Link: https://lore.kernel.org/r/20210227170006.5077-6-michael.christie@oracle.com
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
smatch gives the warning:
drivers/infiniband/ulp/rtrs/rtrs-srv.c:1805 rtrs_rdma_connect() warn: passing zero to 'PTR_ERR'
Which is trying to say smatch has shown that srv is not an error pointer
and thus cannot be passed to PTR_ERR.
The solution is to move the list_add() down after full initilization of
rtrs_srv. To avoid holding the srv_mutex too long, only hold it during the
list operation as suggested by Leon.
Fixes: 03e9b33a0f ("RDMA/rtrs: Only allow addition of path to an already established session")
Link: https://lore.kernel.org/r/20210216143807.65923-1-jinpu.wang@cloud.ionos.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The current code computes a number of channels per SRP target and spreads
them equally across all online NUMA nodes. Each channel is then assigned
a CPU within this node.
In the case of unbalanced, or even unpopulated nodes, some channels do not
get a CPU associated and thus do not get connected. This causes the SRP
connection to fail.
This patch solves the issue by rewriting channel computation and
allocation:
- Drop channel to node/CPU association as it had no real effect on
locality but added unnecessary complexity.
- Tweak the number of channels allocated to reduce CPU contention when
possible:
- Up to one channel per CPU (instead of up to 4 by node)
- At least 4 channels per node, unless ch_count module parameter is
used.
Link: https://lore.kernel.org/r/9cb4d9d3-30ad-2276-7eff-e85f7ddfb411@suse.com
Signed-off-by: Nicolas Morey-Chaisemartin <nmoreychaisemartin@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
put_device() decreases the ref-count and then the device will be
cleaned-up, while at is also add missing put_device in
rtrs_srv_create_once_sysfs_root_folders
This patch solves a kmemleak error as below:
unreferenced object 0xffff88809a7a0710 (size 8):
comm "kworker/4:1H", pid 113, jiffies 4295833049 (age 6212.380s)
hex dump (first 8 bytes):
62 6c 61 00 6b 6b 6b a5 bla.kkk.
backtrace:
[<0000000054413611>] kstrdup+0x2e/0x60
[<0000000078e3120a>] kobject_set_name_vargs+0x2f/0xb0
[<00000000f1a17a6b>] dev_set_name+0xab/0xe0
[<00000000d5502e32>] rtrs_srv_create_sess_files+0x2fb/0x314 [rtrs_server]
[<00000000ed11a1ef>] rtrs_srv_info_req_done+0x631/0x800 [rtrs_server]
[<000000008fc5aa8f>] __ib_process_cq+0x94/0x100 [ib_core]
[<00000000a9599cb4>] ib_cq_poll_work+0x32/0xc0 [ib_core]
[<00000000cfc376be>] process_one_work+0x4bc/0x980
[<0000000016e5c96a>] worker_thread+0x78/0x5c0
[<00000000c20b8be0>] kthread+0x191/0x1e0
[<000000006c9c0003>] ret_from_fork+0x3a/0x50
Fixes: baa5b28b7a ("RDMA/rtrs-srv: Replace device_register with device_initialize and device_add")
Link: https://lore.kernel.org/r/20210212134525.103456-5-jinpu.wang@cloud.ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
kmemleak reported an error as below:
unreferenced object 0xffff8880674b7640 (size 64):
comm "kworker/4:1H", pid 113, jiffies 4296403507 (age 507.840s)
hex dump (first 32 bytes):
69 70 3a 31 39 32 2e 31 36 38 2e 31 32 32 2e 31 ip:192.168.122.1
31 30 40 69 70 3a 31 39 32 2e 31 36 38 2e 31 32 10@ip:192.168.12
backtrace:
[<0000000054413611>] kstrdup+0x2e/0x60
[<0000000078e3120a>] kobject_set_name_vargs+0x2f/0xb0
[<00000000ca2be3ee>] kobject_init_and_add+0xb0/0x120
[<0000000062ba5e78>] rtrs_srv_create_sess_files+0x14c/0x314 [rtrs_server]
[<00000000b45b7217>] rtrs_srv_info_req_done+0x5b1/0x800 [rtrs_server]
[<000000008fc5aa8f>] __ib_process_cq+0x94/0x100 [ib_core]
[<00000000a9599cb4>] ib_cq_poll_work+0x32/0xc0 [ib_core]
[<00000000cfc376be>] process_one_work+0x4bc/0x980
[<0000000016e5c96a>] worker_thread+0x78/0x5c0
[<00000000c20b8be0>] kthread+0x191/0x1e0
[<000000006c9c0003>] ret_from_fork+0x3a/0x50
It is caused by the not-freed kobject of rtrs_srv_sess. The kobject
embedded in rtrs_srv_sess has ref-counter 2 after calling
process_info_req(). Therefore it must call kobject_put twice. Currently
it calls kobject_put only once at rtrs_srv_destroy_sess_files because
kobject_del removes the state_in_sysfs flag and then kobject_put in
free_sess() is not called.
This patch moves kobject_del() into free_sess() so that the kobject of
rtrs_srv_sess can be freed. And also this patch adds the missing call of
sysfs_remove_group() to clean-up the sysfs directory.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20210212134525.103456-4-jinpu.wang@cloud.ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
While adding a path from the client side to an already established
session, it was possible to provide the destination IP to a different
server. This is dangerous.
This commit adds an extra member to the rtrs_msg_conn_req structure, named
first_conn; which is supposed to notify if the connection request is the
first for that session or not.
On the server side, if a session does not exist but the first_conn
received inside the rtrs_msg_conn_req structure is 1, the connection
request is failed. This signifies that the connection request is for an
already existing session, and since the server did not find one, it is an
wrong connection request.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20210212134525.103456-3-jinpu.wang@cloud.ionos.com
Signed-off-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Reviewed-by: Lutz Pogrell <lutz.pogrell@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
BUG: KASAN: stack-out-of-bounds in _mlx4_ib_post_send+0x1bd2/0x2770 [mlx4_ib]
Read of size 4 at addr ffff8880d5a7f980 by task kworker/0:1H/565
CPU: 0 PID: 565 Comm: kworker/0:1H Tainted: G O 5.4.84-storage #5.4.84-1+feature+linux+5.4.y+dbg+20201216.1319+b6b887b~deb10
Hardware name: Supermicro H8QG6/H8QG6, BIOS 3.00 09/04/2012
Workqueue: ib-comp-wq ib_cq_poll_work [ib_core]
Call Trace:
dump_stack+0x96/0xe0
print_address_description.constprop.4+0x1f/0x300
? irq_work_claim+0x2e/0x50
__kasan_report.cold.8+0x78/0x92
? _mlx4_ib_post_send+0x1bd2/0x2770 [mlx4_ib]
kasan_report+0x10/0x20
_mlx4_ib_post_send+0x1bd2/0x2770 [mlx4_ib]
? check_chain_key+0x1d7/0x2e0
? _mlx4_ib_post_recv+0x630/0x630 [mlx4_ib]
? lockdep_hardirqs_on+0x1a8/0x290
? stack_depot_save+0x218/0x56e
? do_profile_hits.isra.6.cold.13+0x1d/0x1d
? check_chain_key+0x1d7/0x2e0
? save_stack+0x4d/0x80
? save_stack+0x19/0x80
? __kasan_slab_free+0x125/0x170
? kfree+0xe7/0x3b0
rdma_write_sg+0x5b0/0x950 [rtrs_server]
The problem is when we send imm_wr, the type should be ib_rdma_wr, so hw
driver like mlx4 can do rdma_wr(wr), so fix it by use the ib_rdma_wr as
type for imm_wr.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20210212134525.103456-2-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When a system receives a REREG event from the SM, then the SM information
in the kernel is marked as invalid and a request is sent to the SM to
update the information. The SM information is invalid in that time period.
However, receiving a REREG also occurs simultaneously in user space
applications that are now trying to rejoin the multicast groups. Some of
those may be sendonly multicast groups which are then failing.
If the SM information is invalid then ib_sa_sendonly_fullmem_support()
returns false. That is wrong because it just means that we do not know yet
if the potentially new SM supports sendonly joins.
Sendonly join was introduced in 2015 and all the Subnet managers have
supported it ever since. So there is no point in checking if a subnet
manager supports it.
Should an old opensm get a request for a sendonly join then the request
will fail. The code that is removed here accomodated that situation and
fell back to a full join.
Falling back to a full join is problematic in itself. The reason to use
the sendonly join was to reduce the traffic on the Infiniband fabric
otherwise one could have just stayed with the regular join. So this patch
may cause users of very old opensms to discover that lots of traffic
needlessly crosses their IB fabrics.
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2101281845160.13303@www.lameter.com
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reduce the number of instructions made for setting protection caps. No
need to do bitwise OR with 0 since we can zero the return value in the
beginning of the function.
Link: https://lore.kernel.org/r/20210111145754.56727-5-mgurtovoy@nvidia.com
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Remove the check from the module_init function.
Link: https://lore.kernel.org/r/20210111145754.56727-3-mgurtovoy@nvidia.com
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
No need to add semicolon after closing bracket.
Link: https://lore.kernel.org/r/20210111145754.56727-2-mgurtovoy@nvidia.com
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use if/else clause instead of "condition ? val1 : val2" to make the code
cleaner and simpler.
Link: https://lore.kernel.org/r/20210110111903.486681-3-mgurtovoy@nvidia.com
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
No need to add semicolon after closing bracket.
Link: https://lore.kernel.org/r/20210110111903.486681-2-mgurtovoy@nvidia.com
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The Linux convention is to have only 1 new line between functions.
Link: https://lore.kernel.org/r/20210110111903.486681-1-mgurtovoy@nvidia.com
Reviewed-by: Israel Rukshin <israelr@nvidia.com>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fix up wr_avail accounting. if wr_cnt is 0, then we do SIGNAL for first
wr, in completion we add queue_depth back, which is not right in the
sense of tracking for available wr.
So fix it by init wr_cnt to 1.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20201217141915.56989-19-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
We do not need to wait for REG_MR completion, so remove the
SIGNAL flag.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20201217141915.56989-18-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
We may want to add new flags, so it's better to use bitmask to check flags.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20201217141915.56989-17-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
For HB, there is no need to generate signal for completion.
Also remove a comment accordingly.
Fixes: c0894b3ea6 ("RDMA/rtrs: core: lib functions shared between client and server modules")
Link: https://lore.kernel.org/r/20201217141915.56989-16-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reported-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Make all failure cases go to the common path to avoid duplicate code.
And some issued existed before.
1. clt need to be freed to avoid memory leak.
2. return ERR_PTR(-ENOMEM) if kobject_create_and_add fails, because
rtrs_clt_open checks the return value of by call "IS_ERR(clt)".
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20201217141915.56989-15-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
We had a few places wr_cqe is not set, which could lead to NULL pointer
deref or GPF in error case.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20201217141915.56989-14-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Let's rename it to rtrs_clt_change_state since the previous one is
killed.
Also update the comment to make it more clear.
Link: https://lore.kernel.org/r/20201217141915.56989-13-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
It is just a wrapper of rtrs_clt_change_state_get_old, and we can reuse
rtrs_clt_change_state_get_old with add the checking of 'old_state' is
valid or not.
Link: https://lore.kernel.org/r/20201217141915.56989-12-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
This is not needed since the label is just after the place.
Link: https://lore.kernel.org/r/20201217141915.56989-11-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Let's wait the inflight permits before free it.
Link: https://lore.kernel.org/r/20201217141915.56989-10-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Since the two functions are called together, let's consolidate them in
a new function rtrs_clt_destroy_sysfs_root.
Link: https://lore.kernel.org/r/20201217141915.56989-9-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Per the comment of kobject_init_and_add, we need to free the memory
by call kobject_put.
Fixes: 215378b838 ("RDMA/rtrs: client: sysfs interface functions")
Fixes: 91b11610af ("RDMA/rtrs: server: sysfs interface functions")
Link: https://lore.kernel.org/r/20201217141915.56989-8-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Reviewed-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The rtrs_iu_free is called in rtrs_iu_alloc if memory is limited, so we
don't need to free the same iu again.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20201217141915.56989-7-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Reviewed-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently rtrs when create_qp use a coarse numbers (bigger in general),
which leads to hardware create more resources which only waste memory
with no benefits.
- SERVICE con,
For max_send_wr/max_recv_wr, it's 2 times SERVICE_CON_QUEUE_DEPTH + 2
- IO con
For max_send_wr/max_recv_wr, it's sess->queue_depth * 3 + 1
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20201217141915.56989-6-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Remove self first to avoid deadlock, we don't want to
use close_work to remove sess sysfs.
Fixes: 91b11610af ("RDMA/rtrs: server: sysfs interface functions")
Link: https://lore.kernel.org/r/20201217141915.56989-5-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Tested-by: Lutz Pogrell <lutz.pogrell@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In this error case, we don't need hold mutex to call close_sess.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20201217141915.56989-4-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Tested-by: Lutz Pogrell <lutz.pogrell@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
rtrs does not have same limit for both max_send_wr and max_recv_wr,
To allow client and server set different values, export in a separate
parameter for rtrs_cq_qp_create.
Also fix the type accordingly, u32 should be used instead of u16.
Fixes: c0894b3ea6 ("RDMA/rtrs: core: lib functions shared between client and server modules")
Link: https://lore.kernel.org/r/20201217141915.56989-2-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Previously the rnbd client requested the rtrs to allocate rnbd_iu
just after the rtrs_iu. So the rnbd client passes the size of
rnbd_iu for rtrs_clt_open() and rtrs creates an array of
rnbd_iu and rtrs_iu.
For IO handling, rnbd_iu exists after the request because we pass
the size of rnbd_iu when setting the tag-set. Therefore we do not
use the rnbd_iu allocated by rtrs for IO handling.
We only use the rnbd_iu allocated by rtrs when doing session
initialization. Almost all rnbd_iu allocated by rtrs are wasted.
By this patch the rnbd client does not request rnbd_iu allocation
to rtrs but allocate it for itself when doing session initialization.
Also remove unused rtrs_permit_to_pdu from rtrs.
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A smaller set of patches, nothing stands out as being particularly major
this cycle:
- Driver bug fixes and updates: bnxt_re, cxgb4, rxe, hns, i40iw, cxgb4,
mlx4 and mlx5
- Bug fixes and polishing for the new rts ULP
- Cleanup of uverbs checking for allowed driver operations
- Use sysfs_emit all over the place
- Lots of bug fixes and clarity improvements for hns
- hip09 support for hns
- NDR and 50/100Gb signaling rates
- Remove dma_virt_ops and go back to using the IB DMA wrappers
- mlx5 optimizations for contiguous DMA regions
-----BEGIN PGP SIGNATURE-----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=9t8b
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A smaller set of patches, nothing stands out as being particularly
major this cycle. The biggest item would be the new HIP09 HW support
from HNS, otherwise it was pretty quiet for new work here:
- Driver bug fixes and updates: bnxt_re, cxgb4, rxe, hns, i40iw,
cxgb4, mlx4 and mlx5
- Bug fixes and polishing for the new rts ULP
- Cleanup of uverbs checking for allowed driver operations
- Use sysfs_emit all over the place
- Lots of bug fixes and clarity improvements for hns
- hip09 support for hns
- NDR and 50/100Gb signaling rates
- Remove dma_virt_ops and go back to using the IB DMA wrappers
- mlx5 optimizations for contiguous DMA regions"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (147 commits)
RDMA/cma: Don't overwrite sgid_attr after device is released
RDMA/mlx5: Fix MR cache memory leak
RDMA/rxe: Use acquire/release for memory ordering
RDMA/hns: Simplify AEQE process for different types of queue
RDMA/hns: Fix inaccurate prints
RDMA/hns: Fix incorrect symbol types
RDMA/hns: Clear redundant variable initialization
RDMA/hns: Fix coding style issues
RDMA/hns: Remove unnecessary access right set during INIT2INIT
RDMA/hns: WARN_ON if get a reserved sl from users
RDMA/hns: Avoid filling sl in high 3 bits of vlan_id
RDMA/hns: Do shift on traffic class when using RoCEv2
RDMA/hns: Normalization the judgment of some features
RDMA/hns: Limit the length of data copied between kernel and userspace
RDMA/mlx4: Remove bogus dev_base_lock usage
RDMA/uverbs: Fix incorrect variable type
RDMA/core: Do not indicate device ready when device enablement fails
RDMA/core: Clean up cq pool mechanism
RDMA/core: Update kernel documentation for ib_create_named_qp()
MAINTAINERS: SOFT-ROCE: Change Zhu Yanjun's email address
...
This series consists of the usual driver updates (ufs, qla2xxx,
smartpqi, target, zfcp, fnic, mpt3sas, ibmvfc) plus a load of
cleanups, a major power management rework and a load of assorted minor
updates. There are a few core updates (formatting fixes being the big
one) but nothing major this cycle.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX9o0KSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbOZAP9D5NTN
J7dJUo2MIMy84YBu+d9ag7yLlNiRWVY2yw5vHwD/Z7JjAVLwz/tzmyjU9//o2J6w
hwhOv6Uto89gLCWSEz8=
=KUPT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, smartpqi,
target, zfcp, fnic, mpt3sas, ibmvfc) plus a load of cleanups, a major
power management rework and a load of assorted minor updates.
There are a few core updates (formatting fixes being the big one) but
nothing major this cycle"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: mpt3sas: Update driver version to 36.100.00.00
scsi: mpt3sas: Handle trigger page after firmware update
scsi: mpt3sas: Add persistent MPI trigger page
scsi: mpt3sas: Add persistent SCSI sense trigger page
scsi: mpt3sas: Add persistent Event trigger page
scsi: mpt3sas: Add persistent Master trigger page
scsi: mpt3sas: Add persistent trigger pages support
scsi: mpt3sas: Sync time periodically between driver and firmware
scsi: qla2xxx: Update version to 10.02.00.104-k
scsi: qla2xxx: Fix device loss on 4G and older HBAs
scsi: qla2xxx: If fcport is undergoing deletion complete I/O with retry
scsi: qla2xxx: Fix the call trace for flush workqueue
scsi: qla2xxx: Fix flash update in 28XX adapters on big endian machines
scsi: qla2xxx: Handle aborts correctly for port undergoing deletion
scsi: qla2xxx: Fix N2N and NVMe connect retry failure
scsi: qla2xxx: Fix FW initialization error on big endian machines
scsi: qla2xxx: Fix crash during driver load on big endian machines
scsi: qla2xxx: Fix compilation issue in PPC systems
scsi: qla2xxx: Don't check for fw_started while posting NVMe command
scsi: qla2xxx: Tear down session if FW say it is down
...
iser_initialize_task_headers() uses in_interrupt() to find out if it is
safe to acquire a mutex.
in_interrupt() is deprecated as it is ill defined and does not provide
what it suggests. Aside of that it covers only parts of the contexts in
which a mutex may not be acquired.
The following callchains exist:
iscsi_queuecommand() *locks* iscsi_session::frwd_lock
-> iscsi_prep_scsi_cmd_pdu()
-> session->tt->init_task() (iscsi_iser_task_init())
-> iser_initialize_task_headers()
-> iscsi_iser_task_xmit() (iscsi_transport::xmit_task)
-> iscsi_iser_task_xmit_unsol_data()
-> iser_send_data_out()
-> iser_initialize_task_headers()
iscsi_data_xmit() *locks* iscsi_session::frwd_lock
-> iscsi_prep_mgmt_task()
-> session->tt->init_task() (iscsi_iser_task_init())
-> iser_initialize_task_headers()
-> iscsi_prep_scsi_cmd_pdu()
-> session->tt->init_task() (iscsi_iser_task_init())
-> iser_initialize_task_headers()
__iscsi_conn_send_pdu() caller has iscsi_session::frwd_lock
-> iscsi_prep_mgmt_task()
-> session->tt->init_task() (iscsi_iser_task_init())
-> iser_initialize_task_headers()
-> session->tt->xmit_task() (
The only callchain that is close to be invoked in preemptible context:
iscsi_xmitworker() worker
-> iscsi_data_xmit()
-> iscsi_xmit_task()
-> conn->session->tt->xmit_task() (iscsi_iser_task_xmit()
In iscsi_iser_task_xmit() there is this check:
if (!task->sc)
return iscsi_iser_mtask_xmit(conn, task);
so it does end up in iser_initialize_task_headers() and
iser_initialize_task_headers() relies on iscsi_task::sc == NULL.
Remove conditional locking of iser_conn::state_mutex because there is no
call chain to do so. Remove the goto label and return early now that there
is no clean up needed.
Link: https://lore.kernel.org/r/20201204174256.62xfcvudndt7oufl@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Max Gurtovoy <maxg@nvidia.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently ipoib choose cq completion vector based on port number, when HCA
only have one port, all the interface recv queue completion are bind to cq
completion vector 0.
To better distribute the load, use same method as __ib_alloc_cq_any to
choose completion vector, with the change, each interface now use
different completion vectors.
Link: https://lore.kernel.org/r/20201013074342.15867-1-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
It is not the kernel style, warning reported by coccicheck:
./ib_isert.c:1104:12-24: WARNING: Comparison to bool
Link: https://lore.kernel.org/r/1604404674-32998-1-git-send-email-zou_wei@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
A few more merge window regressions that didn't make rc1:
- New validation in the DMA layer triggers wrong use of the DMA layer in
rxe, siw and rdmavt
- Accidental change of a hypervisor facing ABI when widening the port
speed u8 to u16 in vmw_pvrdma
- Memory leak on error unwind in SRP target
-----BEGIN PGP SIGNATURE-----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=y+a3
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A few more merge window regressions that didn't make rc1:
- New validation in the DMA layer triggers wrong use of the DMA layer
in rxe, siw and rdmavt
- Accidental change of a hypervisor facing ABI when widening the port
speed u8 to u16 in vmw_pvrdma
- Memory leak on error unwind in SRP target"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/srpt: Fix typo in srpt_unregister_mad_agent docstring
RDMA/vmw_pvrdma: Fix the active_speed and phys_state value
IB/srpt: Fix memory leak in srpt_add_one
RDMA: Fix software RDMA drivers for dma mapping error
htmldocs fails with:
drivers/infiniband/ulp/srpt/ib_srpt.c:630: warning: Function parameter or member 'port_cnt' not described in 'srpt_unregister_mad_agent'
Fixes: 372a178628 ("IB/srpt: Fix memory leak in srpt_add_one")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Drop the sess_cmd_lock by:
- Removing the sess_cmd_list use from LIO core, because it's been
moved to qla2xxx.
- Removing sess_tearing_down check in the I/O path. Instead of using that
bit and the sess_cmd_lock, we rely on the cmd_count percpu ref. To do
this we switch to percpu_ref_kill_and_confirm/percpu_ref_tryget_live.
Link: https://lore.kernel.org/r/1604257174-4524-7-git-send-email-michael.christie@oracle.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cmd.bad_sector currently gets packed into the sense INFORMATION field for
TCM_LOGICAL_BLOCK_{GUARD,APP_TAG,REF_TAG}_CHECK_FAILED errors, which carry
an .add_sector_info flag in the sense_detail_table to ensure this.
In preparation for propagating a byte offset on COMPARE AND WRITE
TCM_MISCOMPARE_VERIFY error, rename cmd.bad_sector to cmd.sense_info and
sense_detail.add_sector_info to sense_detail.add_sense_info so that it
better reflects the sense INFORMATION field destination.
[ddiss: update previously overlooked ib_isert]
Link: https://lore.kernel.org/r/20201031233211.5207-3-ddiss@suse.de
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
number of warnings from the once-noisy docs build process is nearly zero.
Getting to this point has required a lot of work; once there, hopefully we
can keep things that way.
I have packaged this as a separate pull because it does a fair amount of
reaching outside of Documentation/. The changes are all in comments and in
code placement. It's all been in linux-next since last week.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl+hscQPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YgZAH/0JeDA/1VLZYYTmdABz8mjBZsoW9tyPGGztF
nsh5ykdHhL3MeTRwumW5armLVrfKhd1XT+nIzD7OcWlqu+RDOvQ5I95rahr473hP
1SHTjqm3/AlJwQoeS72X5U6QEJQ58e2IwCbP23H3x7I3Q3snEA/HhswzxurfoB/Z
j81YzDV2YPEc0LJWZ5Vn0NEdwP8cdpFv5rojsQmepq7K0yJ7tEHb7/u2cEuUBgXS
8LcYCNPLpiN+q5N8uQ5oDjIUNdLQvP03kgKtQWiCTr4BRydOrDlJie28LIedamEz
anu7UfaVK4bxn+ugRI0g2+aWQKux81ULCinKUWmLRNbcxjhaQqQ=
=hDfp
-----END PGP SIGNATURE-----
Merge tag 'docs-5.10-warnings' of git://git.lwn.net/linux
Pull documentation build warning fixes from Jonathan Corbet:
"This contains a series of warning fixes from Mauro; once applied, the
number of warnings from the once-noisy docs build process is nearly
zero.
Getting to this point has required a lot of work; once there,
hopefully we can keep things that way.
I have packaged this as a separate pull because it does a fair amount
of reaching outside of Documentation/. The changes are all in comments
and in code placement. It's all been in linux-next since last week"
* tag 'docs-5.10-warnings' of git://git.lwn.net/linux: (24 commits)
docs: SafeSetID: fix a warning
amdgpu: fix a few kernel-doc markup issues
selftests: kselftest_harness.h: fix kernel-doc markups
drm: amdgpu_dm: fix a typo
gpu: docs: amdgpu.rst: get rid of wrong kernel-doc markups
drm: amdgpu: kernel-doc: update some adev parameters
docs: fs: api-summary.rst: get rid of kernel-doc include
IB/srpt: docs: add a description for cq_size member
locking/refcount: move kernel-doc markups to the proper place
docs: lockdep-design: fix some warning issues
MAINTAINERS: fix broken doc refs due to yaml conversion
ice: docs fix a devlink info that broke a table
crypto: sun8x-ce*: update entries to its documentation
net: phy: remove kernel-doc duplication
mm: pagemap.h: fix two kernel-doc markups
blk-mq: docs: add kernel-doc description for a new struct member
docs: userspace-api: add iommu.rst to the index file
docs: hwmon: mp2975.rst: address some html build warnings
docs: net: statistics.rst: remove a duplicated kernel-doc
docs: kasan.rst: add two missing blank lines
...
The IBTA specification has new speeds - HDR and NDR, supporting signaling
rate of 50Gb and 100Gb respectively. ethtool support of ipoib driver
translates IB speed to signaling rate. Added translation of HDR and NDR IB
types to rates of 50Gb and 100Gb ethernet speed.
Link: https://lore.kernel.org/r/20201026132904.1338526-1-leon@kernel.org
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Failure in srpt_refresh_port() for the second port will leave MAD
registered for the first one, however, the srpt_add_one() will be marked
as "failed" and SRPT will leak resources for that registered but not used
and released first port.
Unregister the MAD agent for all ports in case of failure.
Fixes: a42d985bd5 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Link: https://lore.kernel.org/r/20201028065051.112430-1-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Make changes to use sysfs_emit in the RDMA code as cocci scripts can not
be written to handle _all_ the possible variants of various sprintf family
uses in sysfs show functions.
While there, make the code more legible and update its style to be more
like the typical kernel styles.
Miscellanea:
o Use intermediate pointers for dereferences
o Add and use string lookup functions
o return early when any intermediate call fails so normal return is
at the bottom of the function
o mlx4/mcg.c:sysfs_show_group: use scnprintf to format intermediate strings
Link: https://lore.kernel.org/r/f5c9e4c9d8dafca1b7b70bd597ee7f8f219c31c8.1602122880.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Changeset c804af2c1d ("IB/srpt: use new shared CQ mechanism")
added a new member for struct srpt_rdma_ch, but didn't add the
corresponding kernel-doc markup, as repoted when doing
"make htmldocs":
./drivers/infiniband/ulp/srpt/ib_srpt.h:331: warning: Function parameter or member 'cq_size' not described in 'srpt_rdma_ch'
Add a description for it.
Fixes: c804af2c1d ("IB/srpt: use new shared CQ mechanism")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Link: https://lore.kernel.org/r/df0e5f0e866b91724299ef569a2da8115e48c0cf.1603791716.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Since the three functions share the similar logic, let's introduce one
common function for it.
Link: https://lore.kernel.org/r/20201023074353.21946-12-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
This function isn't needed since no caller checks the old_state of sess.
Link: https://lore.kernel.org/r/20201023074353.21946-11-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The purpose of srv_mutex is to protect srv_list as in put_srv, so no need
to hold it when allocate memory for srv since it could be time consuming.
Otherwise if one machine has limited memory, rsrv_close_work could be
blocked for a longer time due to the mutex is held by get_or_create_srv
since it can't get memory in time.
INFO: task kworker/1:1:27478 blocked for more than 120 seconds.
Tainted: G O 4.14.171-1-storage #4.14.171-1.3~deb9
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/1:1 D 0 27478 2 0x80000000
Workqueue: rtrs_server_wq rtrs_srv_close_work [rtrs_server]
Call Trace:
? __schedule+0x38c/0x7e0
schedule+0x32/0x80
schedule_preempt_disabled+0xa/0x10
__mutex_lock.isra.2+0x25e/0x4d0
? put_srv+0x44/0x100 [rtrs_server]
put_srv+0x44/0x100 [rtrs_server]
rtrs_srv_close_work+0x16c/0x280 [rtrs_server]
process_one_work+0x1c5/0x3c0
worker_thread+0x47/0x3e0
kthread+0xfc/0x130
? trace_event_raw_event_workqueue_execute_start+0xa0/0xa0
? kthread_create_on_node+0x70/0x70
ret_from_fork+0x1f/0x30
Let's move all the logics from __find_srv_and_get and __alloc_srv to
get_or_create_srv, and remove the two functions. Then it should be safe
for multiple processes to access the same srv since it is protected with
srv_mutex.
And since we don't want to allocate chunks with srv_mutex held, let's
check the srv->refcount after get srv because the chunks could not be
allocated yet.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20201023074353.21946-6-jinpu.wang@cloud.ionos.com
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When rtrs_rdma_conn_established returns error (non-zero value), the error
value is stored in con->cm_err and it cannot trigger
rtrs_rdma_error_recovery. Finally the error of rtrs_rdma_con_established
will be forgot.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20201023074353.21946-5-jinpu.wang@cloud.ionos.com
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
It could happen two kworkers race with each other:
CPU0 CPU1
addr_resolver kworker reconnect kworker
rtrs_clt_rdma_cm_handler
rtrs_rdma_addr_resolved
create_con_cq_qp: s.dev_ref++
"s.dev_ref is 1"
wait in create_cm fails with TIMEOUT
destroy_con_cq_qp: --s.dev_ref
"s.dev_ref is 0"
destroy_con_cq_qp: sess->s.dev = NULL
rtrs_cq_qp_create -> create_qp(con, sess->dev->ib_pd...)
sess->dev is NULL, panic.
To fix the problem using mutex to serialize create_con_cq_qp and
destroy_con_cq_qp.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20201023074353.21946-4-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
As run destroy_con_cq_qp many times doesn't work, remove the comments.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20201023074353.21946-3-jinpu.wang@cloud.ionos.com
Suggested-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
We call destroy_con_cq_qp(con) in rtrs_rdma_addr_resolved() in case route
couldn't be resolved and then again in create_cm() because nothing
happens.
Don't call destroy_con_cq_qp from rtrs_rdma_addr_resolved, create_cm()
does the clean up already.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20201023074353.21946-2-jinpu.wang@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently, iser target support max IO size of 16MiB by default. For some
adapters, allocating this amount of resources might reduce the total
number of possible connections that can be created. For those adapters,
it's preferred to reduce the max IO size to be able to create more
connections. Since there is no handshake procedure for max IO size in iser
protocol, set the default max IO size to 1MiB and add a module parameter
for enabling the option to control it for suitable adapters.
Fixes: 317000b926 ("IB/isert: allocate RW ctxs according to max IO size")
Link: https://lore.kernel.org/r/20201019094628.17202-1-mgurtovoy@nvidia.com
Reported-by: Krishnamraju Eraparaju <krishna2@chelsio.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
There are two flows for handling RDMA_CM_EVENT_ROUTE_RESOLVED, either the
handler triggers a completion and another thread does rdma_connect() or
the handler directly calls rdma_connect().
In all cases rdma_connect() needs to hold the handler_mutex, but when
handler's are invoked this is already held by the core code. This causes
ULPs using the 2nd method to deadlock.
Provide a rdma_connect_locked() and have all ULPs call it from their
handlers.
Link: https://lore.kernel.org/r/0-v2-53c22d5c1405+33-rdma_connect_locking_jgg@nvidia.com
Reported-and-tested-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com>
Fixes: 2a7cec5381 ("RDMA/cma: Fix locking for the RDMA_CM_CONNECT state")
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The typical set of driver updates across the subsystem:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma, hns,
usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where MRA
wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail at
the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist
-----BEGIN PGP SIGNATURE-----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=LKpl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A usual cycle for RDMA with a typical mix of driver and core subsystem
updates:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma,
hns, usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where
MRA wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail
at the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using
it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (191 commits)
RDMA/ucma: Fix use after free in destroy id flow
RDMA/rxe: Handle skb_clone() failure in rxe_recv.c
RDMA/rxe: Move the definitions for rxe_av.network_type to uAPI
RDMA: Explicitly pass in the dma_device to ib_register_device
lib/scatterlist: Do not limit max_segment to PAGE_ALIGNED values
IB/mlx4: Convert rej_tmout radix-tree to XArray
RDMA/rxe: Fix bug rejecting all multicast packets
RDMA/rxe: Fix skb lifetime in rxe_rcv_mcast_pkt()
RDMA/rxe: Remove duplicate entries in struct rxe_mr
IB/hfi,rdmavt,qib,opa_vnic: Update MAINTAINERS
IB/rdmavt: Fix sizeof mismatch
MAINTAINERS: CISCO VIC LOW LATENCY NIC DRIVER
RDMA/bnxt_re: Fix sizeof mismatch for allocation of pbl_tbl.
RDMA/bnxt_re: Use rdma_umem_for_each_dma_block()
RDMA/umem: Move to allocate SG table from pages
lib/scatterlist: Add support in dynamic allocation of SG table from pages
tools/testing/scatterlist: Show errors in human readable form
tools/testing/scatterlist: Rejuvenate bit-rotten test
RDMA/ipoib: Set rtnl_link_ops for ipoib interfaces
RDMA/uverbs: Expose the new GID query API to user space
...
Report the "ipoib pkey", "mode" and "umcast" netlink attributes for every
IPoiB interface type, not just children created with 'ip link add'.
After setting the rtnl_link_ops for the parent interface, implement the
dellink() callback to block users from trying to remove it.
Fixes: 862096a8bb ("IB/ipoib: Add more rtnl_link_ops callbacks")
Link: https://lore.kernel.org/r/20201004132948.26669-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The only usage of these is to pass their address to sysfs_create_group()
and sysfs_remove_group(), both which takes const pointers. Make it const
to allow the compiler to put them in read-only memory.
Link: https://lore.kernel.org/r/20200930224004.24279-3-rikard.falkeborn@gmail.com
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Functions related to nested interface infrastructure such as
netdev_walk_all_{ upper | lower }_dev() pass both private functions
and "data" pointer to handle their own things.
At this point, the data pointer type is void *.
In order to make it easier to expand common variables and functions,
this new netdev_nested_priv structure is added.
In the following patch, a new member variable will be added into this
struct to fix the lockdep issue.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky says:
====================
IBTA declares speed as 16 bits, but kernel stores it in u8. This series
fixes in-kernel declaration while keeping external interface intact.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
due to dependencies.
* branch 'mlx5_active_speed':
RDMA: Fix link active_speed size
RDMA/mlx5: Delete duplicated mlx5_ptys_width enum
net/mlx5: Refactor query port speed functions
A number of driver bug fixes and a few recent regressions:
- Several bug fixes for bnxt_re. Crashing, incorrect data reported,
and corruption on new HW
- Memory leak and crash in rxe
- Fix sysfs corruption in rxe if the netdev name is too long
- Fix a crash on error unwind in the new cq_pool code
- Fix kobject panics in rtrs by working device lifetime properly
- Fix a data corruption bug in iser target related to misaligned buffers
-----BEGIN PGP SIGNATURE-----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=2DDd
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A number of driver bug fixes and a few recent regressions:
- Several bug fixes for bnxt_re. Crashing, incorrect data reported,
and corruption on new HW
- Memory leak and crash in rxe
- Fix sysfs corruption in rxe if the netdev name is too long
- Fix a crash on error unwind in the new cq_pool code
- Fix kobject panics in rtrs by working device lifetime properly
- Fix a data corruption bug in iser target related to misaligned
buffers"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/isert: Fix unaligned immediate-data handling
RDMA/rtrs-srv: Set .release function for rtrs srv device during device init
RDMA/bnxt_re: Remove set but not used variable 'qplib_ctx'
RDMA/core: Fix reported speed and width
RDMA/core: Fix unsafe linked list traversal after failing to allocate CQ
RDMA/bnxt_re: Remove the qp from list only if the qp destroy succeeds
RDMA/bnxt_re: Fix driver crash on unaligned PSN entry address
RDMA/bnxt_re: Restrict the max_gids to 256
RDMA/bnxt_re: Static NQ depth allocation
RDMA/bnxt_re: Fix the qp table indexing
RDMA/bnxt_re: Do not report transparent vlan from QP1
RDMA/mlx4: Read pkey table length instead of hardcoded value
RDMA/rxe: Fix panic when calling kmem_cache_create()
RDMA/rxe: Fix memleak in rxe_mem_init_user
RDMA/rxe: Fix the parent sysfs read when the interface has 15 chars
RDMA/rtrs-srv: Replace device_register with device_initialize and device_add
In similar way to other IB objects, restore the ability to return error on
SRQ destroy. Strictly speaking, this change is not necessary, and provided
here to ensure a symmetrical interface like other destroy functions.
Fixes: 68e326dea1 ("RDMA: Handle SRQ allocations by IB/core")
Link: https://lore.kernel.org/r/20200907120921.476363-5-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently we allocate rx buffers in a single contiguous buffers for
headers (iser and iscsi) and data trailer. This means that most likely the
data starting offset is aligned to 76 bytes (size of both headers).
This worked fine for years, but at some point this broke, resulting in
data corruptions in isert when a command comes with immediate data and the
underlying backend device assumes 512 bytes buffer alignment.
We assume a hard-requirement for all direct I/O buffers to be 512 bytes
aligned. To fix this, we should avoid passing unaligned buffers for I/O.
Instead, we allocate our recv buffers with some extra space such that we
can have the data portion align to 512 byte boundary. This also means that
we cannot reference headers or data using structure but rather
accessors (as they may move based on alignment). Also, get rid of the
wrong __packed annotation from iser_rx_desc as this has only harmful
effects (not aligned to anything).
This affects the rx descriptors for iscsi login and data plane.
Fixes: 3d75ca0ade ("block: introduce multi-page bvec helpers")
Link: https://lore.kernel.org/r/20200904195039.31687-1-sagi@grimberg.me
Reported-by: Stephen Rust <srust@blockbridge.com>
Tested-by: Doug Dumitru <doug@dumitru.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The rnbd_server module's communication manager (cm) initialization depends
on the registration of the "network namespace subsystem" of the RDMA CM
agent module. As such, when the kernel is configured to load the
rnbd_server and the RDMA cma module during initialization; and if the
rnbd_server module is initialized before RDMA cma module, a null ptr
dereference occurs during the RDMA bind operation.
Call trace:
Call Trace:
? xas_load+0xd/0x80
xa_load+0x47/0x80
cma_ps_find+0x44/0x70
rdma_bind_addr+0x782/0x8b0
? get_random_bytes+0x35/0x40
rtrs_srv_cm_init+0x50/0x80
rtrs_srv_open+0x102/0x180
? rnbd_client_init+0x6e/0x6e
rnbd_srv_init_module+0x34/0x84
? rnbd_client_init+0x6e/0x6e
do_one_initcall+0x4a/0x200
kernel_init_freeable+0x1f1/0x26e
? rest_init+0xb0/0xb0
kernel_init+0xe/0x100
ret_from_fork+0x22/0x30
Modules linked in:
CR2: 0000000000000015
All this happens cause the cm init is in the call chain of the module
init, which is not a preferred practice.
So remove the call to rdma_create_id() from the module init call chain.
Instead register rtrs-srv as an ib client, which makes sure that the
rdma_create_id() is called only when an ib device is added.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20200907103106.104530-1-haris.iqbal@cloud.ionos.com
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The device .release function was not being set during the device
initialization. This was leading to the below warning, in error cases when
put_srv was called before device_add was called.
Warning:
Device '(null)' does not have a release() function, it is broken and must
be fixed. See Documentation/kobject.txt.
So, set the device .release function during device initialization in the
__alloc_srv() function.
Fixes: baa5b28b7a ("RDMA/rtrs-srv: Replace device_register with device_initialize and device_add")
Link: https://lore.kernel.org/r/20200907102216.104041-1-haris.iqbal@cloud.ionos.com
Signed-off-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rc3' into rdma.git for-next
Required due to dependencies in following patches.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
There are error cases when we will call free_srv before device kobject is
initialized; in such cases calling put_device generates the following
warning:
kobject: '(null)' (000000009f5445ed): is not initialized, yet
kobject_put() is being called.
So call device_initialize() only once when the server is allocated. If we
end up calling put_srv() and subsequently free_srv(), our call to
put_device() would result in deletion of the obj. Call device_add() later
when we actually have a connection. Correspondingly, call device_del()
instead of device_unregister() when srv->dev_ref falls to 0.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20200811092722.2450-1-haris.iqbal@cloud.ionos.com
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The isert_post_recv function prints an error in case of failures, so no
need for the callers to add another print.
Link: https://lore.kernel.org/r/20200805121231.166162-2-maxg@mellanox.com
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
lockdep triggers a warning from time to time when running a regression
test:
rnbd_client L685: </dev/nullb0@bla> Device disconnected.
rnbd_client L1756: Unloading module
workqueue: WQ_MEM_RECLAIM rtrs_client_wq:rtrs_clt_reconnect_work [rtrs_client] is flushing !WQ_MEM_RECLAIM ib_addr:process_one_req [ib_core]
WARNING: CPU: 2 PID: 18824 at kernel/workqueue.c:2517 check_flush_dependency+0xad/0x130
The root cause is workqueue core expect flushing should not be done for a
!WQ_MEM_RECLAIM wq from a WQ_MEM_RECLAIM workqueue.
In above case ib_addr workqueue without WQ_MEM_RECLAIM, but rtrs_wq
WQ_MEM_RECLAIM.
To avoid the warning, remove the WQ_MEM_RECLAIM flag.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20200724111508.15734-4-haris.iqbal@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
In order to avoid all the clients to start reconnecting at the same time
schedule the reconnect dwork with a random jitter of +[0,8] seconds.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20200724111508.15734-2-haris.iqbal@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Have the driver use shared CQs provided by the rdma core driver. This
provides the advantage of improved efficiency handling interrupts.
Link: https://lore.kernel.org/r/20200722135629.49467-3-maxg@mellanox.com
Signed-off-by: Yamin Friedman <yaminf@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Have the driver use shared CQs provided by the rdma core driver. Since
this provides similar functionality to iser_comp it has been removed.
Now there is no reason to allocate very large CQs when the driver is
loaded while gaining the advantage of shared CQs. Previously when a single
connection was opened a CQ was opened for every core with enough space for
eight connections, this is a very large overhead that in most cases will
not be utilized.
Link: https://lore.kernel.org/r/20200722135629.49467-2-maxg@mellanox.com
Signed-off-by: Yamin Friedman <yaminf@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Have the driver use shared CQs provided by the rdma core driver. Since
this provides similar functionality to iser_comp it has been removed. Now
there is no reason to allocate very large CQs when the driver is loaded
while gaining the advantage of shared CQs.
Link: https://lore.kernel.org/r/20200722135629.49467-1-maxg@mellanox.com
Signed-off-by: Yamin Friedman <yaminf@mellanox.com>
Acked-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Current iSER target code allocates MR pool budget based on queue size.
Since there is no handshake between iSER initiator and target on max IO
size, we'll set the iSER target to support upto 16MiB IO operations and
allocate the correct number of RDMA ctxs according to the factor of MR's
per IO operation. This would guarantee sufficient size of the MR pool for
the required IO queue depth and IO size.
Link: https://lore.kernel.org/r/20200708091908.162263-1-maxg@mellanox.com
Reported-by: Krishnamraju Eraparaju <krishna2@chelsio.com>
Tested-by: Krishnamraju Eraparaju <krishna2@chelsio.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Michael Guralnik says:
====================
This series handles IPoIB child interface creation with setting
interface's HW address.
In current implementation, lladdr requested by user is ignored and
overwritten. Child interface gets the same GID as the parent interface and
a QP number which is assigned by the underlying drivers.
In this series we fix this behavior so that user's requested address is
assigned to the newly created interface.
As specific QP number request is not supported for all vendors, QP number
requested by user will still be overwritten when this is not supported.
Behavior of creation of child interfaces through the sysfs mechanism or
without specifying a requested address, stays the same.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
due to dependencies.
* branch 'mlx5_ipoib_qpn':
RDMA/ipoib: Handle user-supplied address when creating child
net/mlx5: Enable QP number request when creating IPoIB underlay QP
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use the address supplied by user when creating a child interface.
Previously, the address requested by the user was ignored and overridden
with parent's GID and the random QP number assigned to the child.
Link: https://lore.kernel.org/r/20200623110105.1225750-3-leon@kernel.org
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
ipoib_mcast_carrier_on_task() insanely open codes a rtnl_lock() such that
the only time flush_workqueue() can be called is if it also clears
IPOIB_FLAG_OPER_UP.
Thus the flush inside ipoib_flush_ah() will deadlock if it gets unlucky
enough, and lockdep doesn't help us to find it early:
CPU0 CPU1 CPU2
__ipoib_ib_dev_flush()
down_read(vlan_rwsem)
ipoib_vlan_add()
rtnl_trylock()
down_write(vlan_rwsem)
ipoib_mcast_carrier_on_task()
while (!rtnl_trylock())
msleep(20);
ipoib_flush_ah()
flush_workqueue(priv->wq)
Clean up the ah_reaper related functions and lifecycle to make sense:
- Start/Stop of the reaper should only be done in open/stop NDOs, not in
any other places
- cancel and flush of the reaper should only happen in the stop NDO.
cancel is only functional when combined with IPOIB_STOP_REAPER.
- Non-stop places were flushing the AH's just need to flush out dead AH's
synchronously and ignore the background task completely. It is fully
locked and harmless to leave running.
Which ultimately fixes the ABBA deadlock by removing the unnecessary
flush_workqueue() from the problematic place under the vlan_rwsem.
Fixes: efc82eeeae ("IB/ipoib: No longer use flush as a parameter")
Link: https://lore.kernel.org/r/20200625174219.290842-1-kamalheib1@gmail.com
Reported-by: Kamal Heib <kheib@redhat.com>
Tested-by: Kamal Heib <kheib@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Silence documentation build warnings by correcting kernel-doc comments.
./drivers/infiniband/core/verbs.c:1004: warning: Function parameter or member 'uobject' not described in 'ib_create_srq_user'
./drivers/infiniband/core/verbs.c:1004: warning: Function parameter or member 'udata' not described in 'ib_create_srq_user'
./drivers/infiniband/core/umem_odp.c:161: warning: Function parameter or member 'ops' not described in 'ib_umem_odp_alloc_child'
./drivers/infiniband/core/umem_odp.c:225: warning: Function parameter or member 'ops' not described in 'ib_umem_odp_get'
./drivers/infiniband/sw/rdmavt/ah.c:104: warning: Excess function parameter 'ah_attr' description in 'rvt_create_ah'
./drivers/infiniband/sw/rdmavt/ah.c:104: warning: Excess function parameter 'create_flags' description in 'rvt_create_ah'
./drivers/infiniband/ulp/iser/iscsi_iser.h:363: warning: Function parameter or member 'all_list' not described in 'iser_fr_desc'
./drivers/infiniband/ulp/iser/iscsi_iser.h:377: warning: Function parameter or member 'all_list' not described in 'iser_fr_pool'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:148: warning: Function parameter or member 'rsvd0' not described in 'opa_vesw_info'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:148: warning: Function parameter or member 'rsvd1' not described in 'opa_vesw_info'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:148: warning: Function parameter or member 'rsvd2' not described in 'opa_vesw_info'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:148: warning: Function parameter or member 'rsvd3' not described in 'opa_vesw_info'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:148: warning: Function parameter or member 'rsvd4' not described in 'opa_vesw_info'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:205: warning: Function parameter or member 'rsvd0' not described in 'opa_per_veswport_info'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:205: warning: Function parameter or member 'rsvd1' not described in 'opa_per_veswport_info'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:205: warning: Function parameter or member 'rsvd2' not described in 'opa_per_veswport_info'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:205: warning: Function parameter or member 'rsvd3' not described in 'opa_per_veswport_info'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:342: warning: Function parameter or member 'reserved' not described in 'opa_veswport_summary_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:394: warning: Function parameter or member 'rsvd0' not described in 'opa_veswport_error_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:394: warning: Function parameter or member 'rsvd1' not described in 'opa_veswport_error_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:394: warning: Function parameter or member 'rsvd2' not described in 'opa_veswport_error_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:394: warning: Function parameter or member 'rsvd3' not described in 'opa_veswport_error_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:394: warning: Function parameter or member 'rsvd4' not described in 'opa_veswport_error_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:394: warning: Function parameter or member 'rsvd5' not described in 'opa_veswport_error_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:394: warning: Function parameter or member 'rsvd6' not described in 'opa_veswport_error_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:394: warning: Function parameter or member 'rsvd7' not described in 'opa_veswport_error_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:394: warning: Function parameter or member 'rsvd8' not described in 'opa_veswport_error_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:394: warning: Function parameter or member 'rsvd9' not described in 'opa_veswport_error_counters'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:460: warning: Function parameter or member 'reserved' not described in 'opa_vnic_vema_mad'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:485: warning: Function parameter or member 'reserved' not described in 'opa_vnic_notice_attr'
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:500: warning: Function parameter or member 'reserved' not described in 'opa_vnic_vema_mad_trap'
Link: https://lore.kernel.org/r/5373936.DvuYhMxLoT@laptop.coltonlewis.name
Signed-off-by: Colton Lewis <colton.w.lewis@protonmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The callers pass the pointer '&req' or 'private_data' to
srpt_cm_req_recv(), and 'private_data' is initialized in srp_send_req().
'sdev' is allocated and stored in srpt_add_one(). It's easy to show that
sdev and req are always valid. So we remove unnecessary WARN_ON.
Link: https://lore.kernel.org/r/20200617140803.181333-1-jingxiangfeng@huawei.com
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
A few large, long discussed works this time. The RNBD block driver has
been posted for nearly two years now, and the removal of FMR has been a
recurring discussion theme for a long time. The usual smattering of
features and bug fixes.
- Various small driver bugs fixes in rxe, mlx5, hfi1, and efa
- Continuing driver cleanups in bnxt_re, hns
- Big cleanup of mlx5 QP creation flows
- More consistent use of src port and flow label when LAG is used and a
mlx5 implementation
- Additional set of cleanups for IB CM
- 'RNBD' network block driver and target. This is a network block RDMA
device specific to ionos's cloud environment. It brings strong multipath
and resiliency capabilities.
- Accelerated IPoIB for HFI1
- QP/WQ/SRQ ioctl migration for uverbs, and support for multiple async fds
- Support for exchanging the new IBTA defiend ECE data during RDMA CM
exchanges
- Removal of the very old and insecure FMR interface from all ULPs and
drivers. FRWR should be preferred for at least a decade now.
-----BEGIN PGP SIGNATURE-----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=9zTe
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A more active cycle than most of the recent past, with a few large,
long discussed works this time.
The RNBD block driver has been posted for nearly two years now, and
flowing through RDMA due to it also introducing a new ULP.
The removal of FMR has been a recurring discussion theme for a long
time.
And the usual smattering of features and bug fixes.
Summary:
- Various small driver bugs fixes in rxe, mlx5, hfi1, and efa
- Continuing driver cleanups in bnxt_re, hns
- Big cleanup of mlx5 QP creation flows
- More consistent use of src port and flow label when LAG is used and
a mlx5 implementation
- Additional set of cleanups for IB CM
- 'RNBD' network block driver and target. This is a network block
RDMA device specific to ionos's cloud environment. It brings strong
multipath and resiliency capabilities.
- Accelerated IPoIB for HFI1
- QP/WQ/SRQ ioctl migration for uverbs, and support for multiple
async fds
- Support for exchanging the new IBTA defiend ECE data during RDMA CM
exchanges
- Removal of the very old and insecure FMR interface from all ULPs
and drivers. FRWR should be preferred for at least a decade now"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (247 commits)
RDMA/cm: Spurious WARNING triggered in cm_destroy_id()
RDMA/mlx5: Return ECE DC support
RDMA/mlx5: Don't rely on FW to set zeros in ECE response
RDMA/mlx5: Return an error if copy_to_user fails
IB/hfi1: Use free_netdev() in hfi1_netdev_free()
RDMA/hns: Uninitialized variable in modify_qp_init_to_rtr()
RDMA/core: Move and rename trace_cm_id_create()
IB/hfi1: Fix hfi1_netdev_rx_init() error handling
RDMA: Remove 'max_map_per_fmr'
RDMA: Remove 'max_fmr'
RDMA/core: Remove FMR device ops
RDMA/rdmavt: Remove FMR memory registration
RDMA/mthca: Remove FMR support for memory registration
RDMA/mlx4: Remove FMR support for memory registration
RDMA/i40iw: Remove FMR leftovers
RDMA/bnxt_re: Remove FMR leftovers
RDMA/mlx5: Remove FMR leftovers
RDMA/core: Remove FMR pool API
RDMA/rds: Remove FMR support for memory registration
RDMA/srp: Remove support for FMR memory registration
...
FMR is not supported on most recent RDMA devices (that use fast memory
registration mechanism). Also, FMR was recently removed from NFS/RDMA
ULP.
Link: https://lore.kernel.org/r/2-v3-f58e6669d5d3+2cf-fmr_removal_jgg@mellanox.com
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
FMR is not supported on most recent RDMA devices (that use fast memory
registration mechanism). Also, FMR was recently removed from NFS/RDMA
ULP.
Link: https://lore.kernel.org/r/1-v3-f58e6669d5d3+2cf-fmr_removal_jgg@mellanox.com
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The ib_srpt driver limits max_send_sge to 16. Since that is a workaround
for an mlx4 bug that has been fixed, increase max_send_sge. See also
commit f95ccffc71 ("IB/mlx4: Use 4K pages for kernel QP's WQE buffer").
Link: https://lore.kernel.org/r/20200525172212.14413-5-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Since srpt_post_recv() always sets num_sge to 1, reduce the max_recv_sge
parameter that is used at queue pair allocation time to 1.
Link: https://lore.kernel.org/r/20200525172212.14413-4-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Since the session name by itself is not sufficient to uniquely identify a
queue pair, include the queue pair number. Show the ASCII channel state
name instead of the numeric value. This change makes the ib_srpt debug
output more consistent.
Link: https://lore.kernel.org/r/20200525172212.14413-3-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Increase the flexibility of the SRP initiator driver by making the channel
count configurable per target instead of only providing a kernel module
parameter for configuring the channel count.
Link: https://lore.kernel.org/r/20200525172212.14413-2-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When connected mode is set, and we have connected and datagram traffic in
parallel, ipoib might crash with double free of datagram skb.
The current mechanism assumes that the order in the completion queue is
the same as the order of sent packets for all QPs. Order is kept only for
specific QP, in case of mixed UD and CM traffic we have few QPs (one UD and
few CM's) in parallel.
The problem:
----------------------------------------------------------
Transmit queue:
-----------------
UD skb pointer kept in queue itself, CM skb kept in spearate queue and
uses transmit queue as a placeholder to count the number of total
transmitted packets.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 .........127
------------------------------------------------------------
NL ud1 UD2 CM1 ud3 cm2 cm3 ud4 cm4 ud5 NL NL NL ...........
------------------------------------------------------------
^ ^
tail head
Completion queue (problematic scenario) - the order not the same as in
the transmit queue:
1 2 3 4 5 6 7 8 9
------------------------------------
ud1 CM1 UD2 ud3 cm2 cm3 ud4 cm4 ud5
------------------------------------
1. CM1 'wc' processing
- skb freed in cm separate ring.
- tx_tail of transmit queue increased although UD2 is not freed.
Now driver assumes UD2 index is already freed and it could be used for
new transmitted skb.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 .........127
------------------------------------------------------------
NL NL UD2 CM1 ud3 cm2 cm3 ud4 cm4 ud5 NL NL NL ...........
------------------------------------------------------------
^ ^ ^
(Bad)tail head
(Bad - Could be used for new SKB)
In this case (due to heavy load) UD2 skb pointer could be replaced by new
transmitted packet UD_NEW, as the driver assumes its free. At this point
we will have to process two 'wc' with same index but we have only one
pointer to free.
During second attempt to free the same skb we will have NULL pointer
exception.
2. UD2 'wc' processing
- skb freed according the index we got from 'wc', but it was already
overwritten by mistake. So actually the skb that was released is the
skb of the new transmitted packet and not the original one.
3. UD_NEW 'wc' processing
- attempt to free already freed skb. NUll pointer exception.
The fix:
-----------------------------------------------------------------------
The fix is to stop using the UD ring as a placeholder for CM packets, the
cyclic ring variables tx_head and tx_tail will manage the UD tx_ring, a
new cyclic variables global_tx_head and global_tx_tail are introduced for
managing and counting the overall outstanding sent packets, then the send
queue will be stopped and waken based on these variables only.
Note that no locking is needed since global_tx_head is updated in the xmit
flow and global_tx_tail is updated in the NAPI flow only. A previous
attempt tried to use one variable to count the outstanding sent packets,
but it did not work since xmit and NAPI flows can run at the same time and
the counter will be updated wrongly. Thus, we use the same simple cyclic
head and tail scheme that we have today for the UD tx_ring.
Fixes: 2c104ea683 ("IB/ipoib: Get rid of the tx_outstanding variable in all modes")
Link: https://lore.kernel.org/r/20200527134705.480068-1-leon@kernel.org
Signed-off-by: Valentine Fatiev <valentinef@mellanox.com>
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
IBTA declares "vendor option not supported" reject reason in REJ messages
if passive side doesn't want to accept proposed ECE options.
Due to the fact that ECE is managed by userspace, there is a need to let
users to provide such rejected reason.
Link: https://lore.kernel.org/r/20200526103304.196371-7-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
can_sleep is always 0 when iboib_mcast_alloc() is called, so remove it and
use GFP_ATOMIC instead of GFP_KERNEL.
Link: https://lore.kernel.org/r/20200525130305.171509-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The macros do_each_path/while_each_path lead to a smatch warning:
drivers/infiniband/ulp/rtrs/rtrs-clt.c:1196 rtrs_clt_failover_req() warn: inconsistent indenting
drivers/infiniband/ulp/rtrs/rtrs-clt.c:2890 rtrs_clt_request() warn: inconsistent indenting
Also checkpatch complains:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
The macros are used only in two places: for a normal IO path and for the
failover path triggered after errors.
Get rid of the macros and just use a for loop iterating over the list of
paths in both places. It is easier to read and also less lines of code.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20200522053924.528980-1-danil.kipnis@cloud.ionos.com
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The rtrs_sess structure has already been extracted above from the
rtrs_srv_sess structure. Use that to avoid redundant dereferencing.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20200522082833.1480551-1-haris.phnx@gmail.com
Signed-off-by: Md Haris Iqbal <haris.phnx@gmail.com>
Acked-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This is the prerequisite modification to the ipoib ulp to allow a
rdma netdev to obtain the default ndo ops for init/uninit/open/close.
This is accomplished by setting the netdev ops field within the
callback function passed to the netdev allocation routine which
in turn was passed into the rdma netdev allocation routine.
This allows the rdma netdev to call back into the ulp to create the
resources required for connected mode operation.
Additionally as the ulp is not re-entrant, when switching modes,
the number of real tx queues is set to 1 for the connected mode.
For datagram mode the number of real tx queues is set to the
actual number of tx queues specified at the netdev's allocation.
For the internal ulp netdev the number of tx queues defaults to 1.
It is up to the rdma netdev to specify the actual number it can support.
When the driver does not support a rdma netdev for acceleration,
(-ENOTSUPPORTED return code or the verbs function for allocation is
NULL) the ipoib ulp functions are unaffected by using the internal
netdev allocated by the ipoib ulp.
Link: https://lore.kernel.org/r/20200511160706.173205.19086.stgit@awfm-01.aw.intel.com
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Gary Leshner <Gary.S.Leshner@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When in connected mode ipoib sent broadcast pings which exceeded the mtu
size for broadcast addresses.
Add an mtu attribute to the rdma_netdev structure which ipoib sets to its
mcast mtu size.
The RDMA netdev uses this value to determine if the skb length is too long
for the mtu specified and if it is, drops the packet and logs an error
about the errant packet.
Link: https://lore.kernel.org/r/20200511160655.173205.14546.stgit@awfm-01.aw.intel.com
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Gary Leshner <Gary.S.Leshner@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently the ipoib UD mtu is restricted to 4K bytes. Remove this
limitation so that the IPOIB module can potentially use an MTU (in UD
mode) that is bounded by the MTU of the underlying device. A field is
added to the ib_port_attr structure to indicate the maximum physical
MTU the underlying device supports.
Link: https://lore.kernel.org/r/20200511160618.173205.23053.stgit@awfm-01.aw.intel.com
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sadanand Warrier <sadanand.warrier@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Adds capability to create a qpn to be recognized as an accelerated
UD QP for ipoib.
This is accomplished by reserving 0x81 in byte[0] of the qpn as the
prefix for these qp types and reserving qpns between 0x810000 and
0x81ffff.
The hfi1 capability mask already contained a flag for the VNIC netdev.
This has been renamed and extended to include both VNIC and ipoib.
The rvt code to allocate qps now recognizes this flag and sets 0x81
into byte[0] of the qpn.
The code to allocate qpns is modified to reset the qpn numbering when it
is detected that a value is located in byte[0] for a UD QP and it is a
qpn being requested for net dev use. If it is a regular UD QP then it is
allowable to have bits set in byte[0] of the qpn and provide the
previously normal behavior.
The code to free the qpn now checks for the AIP prefix value of 0x81 and
removes it from the qpn before being freed so that the lower 16 bit
number can be reused.
This patch requires minor changes in the IB core and ipoib to facilitate
the creation of accelerated UP QPs.
Link: https://lore.kernel.org/r/20200511160607.173205.11757.stgit@awfm-01.aw.intel.com
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Gary Leshner <Gary.S.Leshner@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When Block Device Layer is disabled, BLK_MAX_SEGMENT_SIZE is undefined.
The rtrs is a transport library and should compile independently of the
block layer. The desired max segment size should be passed down by the
user.
Introduce max_segment_size parameter for the rtrs_clt_open() call.
Fixes: f7a7a5c228 ("block/rnbd: client: main functionality")
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Fixes: cb80329c94 ("RDMA/rtrs: client: private header with client structs and functions")
Fixes: b5c27cdb09 ("RDMA/rtrs: public interface header to establish RDMA connections")
Link: https://lore.kernel.org/r/20200519111419.924170-1-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix to return negative error code -ENOMEM from the some error handling
cases instead of 0, as done elsewhere in this function.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Fixes: 91b11610af ("RDMA/rtrs: server: sysfs interface functions")
Link: https://lore.kernel.org/r/20200519091912.134358-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Remove the if-statement and return the value contained in _err_,
unconditionally.
Link: https://lore.kernel.org/r/20200519163612.GA6043@embeddedor
Addresses-Coverity-ID: 1493753 ("Identical code for different branches")
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
These > comparisons should be >= to prevent accessing one element beyond
the end of the buffer.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20200519154525.GA66801@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The problem is that "req->sg_cnt" is an unsigned int so if "nr" is
negative, it gets type promoted to a high positive value and the condition
is false. This patch fixes it by handling negatives separately.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20200519133223.GN2078@kadam
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Avoid disabling device management for devices that don't support
Management datagrams (MADs) by checking if the "mad_agent" pointer is
initialized before calling ib_modify_port, also fix the error flow in
srpt_refresh_port() to disable device management if
ib_register_mad_agent() fail.
Fixes: 09f8a1486d ("RDMA/srpt: Fix handling of SR-IOV and iWARP ports")
Link: https://lore.kernel.org/r/20200514114720.141139-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When I cat module parameter 'srpt_service_guid', it displays as follows.
It is better to add a newline for easy reading.
[root@hulk-202 ~]# cat /sys/module/ib_srpt/parameters/srpt_service_guid
0x0205cdfffe8346b9[root@hulk-202 ~]#
Link: https://lore.kernel.org/r/1589182629-27743-1-git-send-email-wangxiongfeng2@huawei.com
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add rtrs Makefile, Kconfig and also corresponding lines into upper layer
infiniband/ulp files.
Link: https://lore.kernel.org/r/20200511135131.27580-14-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This is the sysfs interface to rtrs sessions on server side:
/sys/class/rtrs-server/<SESS-NAME>/
*** rtrs session accepted from a client peer
|
|- paths/<SRC@DST>/
*** established paths from a client in a session
|
|- disconnect
| *** disconnect path
|
|- hca_name
| *** HCA name
|
|- hca_port
| *** HCA port
|
|- stats/
*** current path statistics
|
|- rdma
Link: https://lore.kernel.org/r/20200511135131.27580-13-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This introduces set of functions used on server side to account statistics
of RDMA data sent/received.
Link: https://lore.kernel.org/r/20200511135131.27580-12-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This is main functionality of rtrs-server module, which accepts set of
RDMA connections (so called rtrs session), creates/destroys sysfs entries
associated with rtrs session and notifies upper layer
(user of RTRS API) about RDMA requests or link events.
Link: https://lore.kernel.org/r/20200511135131.27580-11-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This header describes main structs and functions used by rtrs-server
module, mainly for accepting rtrs sessions, creating/destroying sysfs
entries, accounting statistics on server side.
Link: https://lore.kernel.org/r/20200511135131.27580-10-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This is the sysfs interface to rtrs sessions on client side:
/sys/class/rtrs-client/<SESS-NAME>/
*** rtrs session created by rtrs_clt_open() API call
|
|- max_reconnect_attempts
| *** number of reconnect attempts for session
|
|- add_path
| *** adds another connection path into rtrs session
|
|- paths/<SRC@DST>/
*** established paths to server in a session
|
|- disconnect
| *** disconnect path
|
|- reconnect
| *** reconnect path
|
|- remove_path
| *** remove current path
|
|- state
| *** retrieve current path state
|
|- hca_port
| *** HCA port number
|
|- hca_name
| *** HCA name
|
|- stats/
*** current path statistics
|
|- cpu_migration
|- rdma
|- reconnects
|- reset_all
Link: https://lore.kernel.org/r/20200511135131.27580-9-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This introduces set of functions used on client side to account statistics
of RDMA data sent/received, amount of IOs inflight, latency, cpu
migrations, etc. Almost all statistics are collected using percpu
variables.
Link: https://lore.kernel.org/r/20200511135131.27580-8-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This is main functionality of rtrs-client module, which manages set of
RDMA connections for each rtrs session, does multipathing, load balancing
and failover of RDMA requests.
Link: https://lore.kernel.org/r/20200511135131.27580-7-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This header describes main structs and functions used by rtrs-client
module, mainly for managing rtrs sessions, creating/destroying sysfs
entries, accounting statistics on client side.
Link: https://lore.kernel.org/r/20200511135131.27580-6-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This is a set of library functions existing as a rtrs-core module, used by
client and server modules.
Mainly these functions wrap IB and RDMA calls and provide a bit higher
abstraction for implementing of RTRS protocol on client or server sides.
Link: https://lore.kernel.org/r/20200511135131.27580-5-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
These are common private headers with rtrs protocol structures, logging,
sysfs and other helper functions, which are used on both client and server
sides.
Link: https://lore.kernel.org/r/20200511135131.27580-4-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Introduce public header which provides set of API functions to establish
RDMA connections from client to server machine using RTRS protocol, which
manages RDMA connections for each session, does multipathing and load
balancing.
Main functions for client (active) side:
rtrs_clt_open() - Creates set of RDMA connections incapsulated
in IBTRS session and returns pointer on RTRS
session object.
rtrs_clt_close() - Closes RDMA connections associated with RTRS
session.
rtrs_clt_request() - Requests zero-copy RDMA transfer to/from
server.
Main functions for server (passive) side:
rtrs_srv_open() - Starts listening for RTRS clients on specified
port and invokes RTRS callbacks for incoming
RDMA requests or link events.
rtrs_srv_close() - Closes RTRS server context.
Link: https://lore.kernel.org/r/20200511135131.27580-3-danil.kipnis@cloud.ionos.com
Signed-off-by: Danil Kipnis <danil.kipnis@cloud.ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When a client is added it isn't allowed to fail, but all the client's have
various failure paths within their add routines.
This creates the very fringe condition where the client was added, failed
during add and didn't set the client_data. The core code will then still
call other client_data centric ops like remove(), rename(), get_nl_info(),
and get_net_dev_by_params() with NULL client_data - which is confusing and
unexpected.
If the add() callback fails, then do not call any more client ops for the
device, even remove.
Remove all the now redundant checks for NULL client_data in ops callbacks.
Update all the add() callbacks to return error codes
appropriately. EOPNOTSUPP is used for cases where the ULP does not support
the ib_device - eg because it only works with IB.
Link: https://lore.kernel.org/r/20200421172440.387069-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The majority of the patches are cleanups, refactorings and clarity
improvements
- Various driver updates for siw, bnxt_re, rxe, efa, mlx5, hfi1
- Lots of cleanup patches for hns
- Convert more places to use refcount
- Aggressively lock the RDMA CM code that syzkaller says isn't working
- Work to clarify ib_cm
- Use the new ib_device lifecycle model in bnxt_re
- Fix mlx5's MR cache which seems to be failing more often with the new
ODP code
- mlx5 'dynamic uar' and 'tx steering' user interfaces
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEfB7FMLh+8QxL+6i3OG33FX4gmxoFAl6CSr0ACgkQOG33FX4g
mxrtKg//XovbOfYAO7nC05FtGz9iEkIUBiwQOjUojgNSi6RMNDqRW1bmqKUugm1o
9nXA6tw+fueEvUNSD541SCcxkUZJzWvubO9wHB6N3Fgy68N3Vf2rKV3EBBTh99rK
Cb7rnmTTN6izRyI1wdyP2sjDJGyF8zvsgIrG2sibzLnqlyScrnD98YS0FdPZUfOa
a1mmXBN/T7eaQ4TbE3lLLzGnifRlGmZ5vxEvOQmAlOdqAfIKQdbbW7oCRLVIleso
gfQlOOvIgzHRwQ3VrFa3i6ETYtywXq7EgmQxCjqPVJQjCA79n5TLBkP1iRhvn8xi
3+LO4YCkiSJ/NjTA2d9KwT6K4djj3cYfcueuqo2MoXXr0YLiY6TLv1OffKcUIq7c
LM3d4CSwIAG+C2FZwaQrdSGa2h/CNfLAEeKxv430zggeDNKlwHJPV5w3rUJ8lT56
wlyT7Lzosl0O9Z/1BSLYckTvbBCtYcmanVyCfHG8EJKAM1/tXy5LS8btJ3e51rPu
XekR9ELrTTA2CTuoSCQGP6J0dBD2U7qO4XRCQ9N5BYLrI6RdP7Z4xYzzey49Z3Cx
JaF86eurM7nS5biUszTtwww8AJMyYicB+0VyjBfk+mhv90w8tS1vZ1aZKzaQ1L6Z
jWn8WgIN4rWY0YGQs6PiovT1FplyGs3p1wNmjn92WO0wZZ3WsmQ=
=ae+a
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"The majority of the patches are cleanups, refactorings and clarity
improvements.
This cycle saw some more activity from Syzkaller, I think we are now
clean on all but one of those bugs, including the long standing and
obnoxious rdma_cm locking design defect. Continue to see many drivers
getting cleanups, with a few new user visible features.
Summary:
- Various driver updates for siw, bnxt_re, rxe, efa, mlx5, hfi1
- Lots of cleanup patches for hns
- Convert more places to use refcount
- Aggressively lock the RDMA CM code that syzkaller says isn't
working
- Work to clarify ib_cm
- Use the new ib_device lifecycle model in bnxt_re
- Fix mlx5's MR cache which seems to be failing more often with the
new ODP code
- mlx5 'dynamic uar' and 'tx steering' user interfaces"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (144 commits)
RDMA/bnxt_re: make bnxt_re_ib_init static
IB/qib: Delete struct qib_ivdev.qp_rnd
RDMA/hns: Fix uninitialized variable bug
RDMA/hns: Modify the mask of QP number for CQE of hip08
RDMA/hns: Reduce the maximum number of extend SGE per WQE
RDMA/hns: Reduce PFC frames in congestion scenarios
RDMA/mlx5: Add support for RDMA TX flow table
net/mlx5: Add support for RDMA TX steering
IB/hfi1: Call kobject_put() when kobject_init_and_add() fails
IB/hfi1: Fix memory leaks in sysfs registration and unregistration
IB/mlx5: Move to fully dynamic UAR mode once user space supports it
IB/mlx5: Limit the scope of struct mlx5_bfreg_info to mlx5_ib
IB/mlx5: Extend QP creation to get uar page index from user space
IB/mlx5: Extend CQ creation to get uar page index from user space
IB/mlx5: Expose UAR object and its alloc/destroy commands
IB/hfi1: Get rid of a warning
RDMA/hns: Remove redundant judgment of qp_type
RDMA/hns: Remove redundant assignment of wc->smac when polling cq
RDMA/hns: Remove redundant qpc setup operations
RDMA/hns: Remove meaningless prints
...
The right markup for a variable is @foo, and not @foo[].
Using a wrong markup caused this warning:
./drivers/infiniband/ulp/opa_vnic/opa_vnic_encap.h:243: WARNING: Inline strong start-string without end-string.
Link: https://lore.kernel.org/r/9dce702510505556d75a13d9641e09218a4b4a65.1584456635.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
libiscsi calls the check_protection transport handler only if SCSI-Respose
is received. So, the handler is never called if iSCSI task is completed
for some other reason like a timeout or error handling. And this behavior
looks correct. But the iSER does not handle this case properly because it
puts a non-checked signature MR to the free pool. Then the error occurs at
reusing the MR because it is not allowed to invalidate a signature MR
without checking.
This commit adds an extra check to iser_unreg_mem_fastreg(), which is a
part of the task cleanup flow. Now the signature MR is checked there if it
is needed.
Link: https://lore.kernel.org/r/20200325151210.1548-1-sergeygo@mellanox.com
Signed-off-by: Sergey Gorenko <sergeygo@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5cOX8eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGw0AH/0nex1uEpzUTm+Gw
D8QPFr3y61sYLu7sIMVt39+Zl6OSxvOOX14QIM/mrNrzjjRI8EXGvYgES5gSO4on
6NLS6/64c1oQThDHCsxusKoSWLZ9KqP2vRPt7tZjn7DZMzEsuLhlINKBeupcqALX
FnOBr768P+if/j0WcDR2pBaMg3ch+XC5sfYav7kapjgWUqCx9BvrHKLXXdlEGUC0
7Ku7PH+nF7CIHiTay+i89odvOd8aLGsa/SUf5XGauKkH65VgQkmksgPeZUPqTnyC
MEsyLJLfn4AP3ySwqzfSLac8jqZG8FGBt4DgM2MQBHibctzfeMIznfcfh/A8+Edx
jqLKLAs=
=4075
-----END PGP SIGNATURE-----
Merge tag 'v5.6-rc4' into rdma.git for-next
Required due to dependencies in following patches.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The default version provided by "ethtool -i" it the correct way
to identify Driver version. There is no need to overwrite it.
Link: https://lore.kernel.org/r/20200220071239.231800-3-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
There is no need to set driver version in in-tree kernel code.
Link: https://lore.kernel.org/r/20200220071239.231800-2-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Link: https://lore.kernel.org/r/20200213010425.GA13068@embeddedor.com
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> # added a few more
- Driver updates and cleanup for qedr, bnxt_re, hns, siw, mlx5, mlx4, rxe,
i40iw
- Larger series doing cleanup and rework for hns and hfi1.
- Some general reworking of the CM code to make it a little more
understandable
- Unify the different code paths connected to the uverbs FD scheme
- New UAPI ioctls conversions for get context and get async fd
- Trace points for CQ and CM portions of the RDMA stack
- mlx5 driver support for virtio-net formatted rings as RDMA raw ethernet QPs
- verbs support for setting the PCI-E relaxed ordering bit on DMA traffic
connected to a MR
- A couple of bug fixes that came too late to make rc7
-----BEGIN PGP SIGNATURE-----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=hepK
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A very quiet cycle with few notable changes. Mostly the usual list of
one or two patches to drivers changing something that isn't quite rc
worthy. The subsystem seems to be seeing a larger number of rework and
cleanup style patches right now, I feel that several vendors are
prepping their drivers for new silicon.
Summary:
- Driver updates and cleanup for qedr, bnxt_re, hns, siw, mlx5, mlx4,
rxe, i40iw
- Larger series doing cleanup and rework for hns and hfi1.
- Some general reworking of the CM code to make it a little more
understandable
- Unify the different code paths connected to the uverbs FD scheme
- New UAPI ioctls conversions for get context and get async fd
- Trace points for CQ and CM portions of the RDMA stack
- mlx5 driver support for virtio-net formatted rings as RDMA raw
ethernet QPs
- verbs support for setting the PCI-E relaxed ordering bit on DMA
traffic connected to a MR
- A couple of bug fixes that came too late to make rc7"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (108 commits)
RDMA/core: Make the entire API tree static
RDMA/efa: Mask access flags with the correct optional range
RDMA/cma: Fix unbalanced cm_id reference count during address resolve
RDMA/umem: Fix ib_umem_find_best_pgsz()
IB/mlx4: Fix leak in id_map_find_del
IB/opa_vnic: Spelling correction of 'erorr' to 'error'
IB/hfi1: Fix logical condition in msix_request_irq
RDMA/cm: Remove CM message structs
RDMA/cm: Use IBA functions for complex structure members
RDMA/cm: Use IBA functions for simple structure members
RDMA/cm: Use IBA functions for swapping get/set acessors
RDMA/cm: Use IBA functions for simple get/set acessors
RDMA/cm: Add SET/GET implementations to hide IBA wire format
RDMA/cm: Add accessors for CM_REQ transport_type
IB/mlx5: Return the administrative GUID if exists
RDMA/core: Ensure that rdma_user_mmap_entry_remove() is a fence
IB/mlx4: Fix memory leak in add_gid error flow
IB/mlx5: Expose RoCE accelerator counters
RDMA/mlx5: Set relaxed ordering when requested
RDMA/core: Add the core support field to METHOD_GET_CONTEXT
...
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
Two last minute fixes, both in drivers. The fnic one is a highly
unlikely condition, but the RDMA one is a recently introduced
regression that causes a kernel warning to trigger in every RDMA
logon, which would be unsightly if it got into the final release.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJsEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXi3VRyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbrpAP9I/pEp
TWu/QkqFFrmuYbzuxtRML7X2T7+B96J/CRtQvQD3TAIW0gvw49Uj25yEwTRnVzCs
1A+eELAahzBPW+rRBw==
=C3yx
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two last minute fixes, both in drivers.
The fnic one is a highly unlikely condition, but the RDMA one is a
recently introduced regression that causes a kernel warning to trigger
in every RDMA logon, which would be unsightly if it got into the final
release"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: RDMA/isert: Fix a recently introduced regression related to logout
scsi: fnic: do not queue commands during fwreset
Correcting a minor spelling mistake in the comments.
Link: https://lore.kernel.org/r/20200118162542.15188-1-dab9861@gmail.com
Signed-off-by: Dillon Brock <dab9861@gmail.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
iscsit_close_connection() calls isert_wait_conn(). Due to commit
e9d3009cb9 both functions call target_wait_for_sess_cmds() although that
last function should be called only once. Fix this by removing the
target_wait_for_sess_cmds() call from isert_wait_conn() and by only calling
isert_wait_conn() after target_wait_for_sess_cmds().
Fixes: e9d3009cb9 ("scsi: target: iscsi: Wait for all commands to finish before freeing a session").
Link: https://lore.kernel.org/r/20200116044737.19507-1-bvanassche@acm.org
Reported-by: Rahul Kundu <rahul.kundu@chelsio.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some SRP targets that do not support specification SRP-2, put the garbage
to the reserved bits of the SRP login response. The problem was not
detected for a long time because the SRP initiator ignored those bits. But
now one of them is used as SRP_LOGIN_RSP_IMMED_SUPP. And it causes a
critical error on the target when the initiator sends immediate data.
The ib_srp module has a use_imm_date parameter to enable or disable
immediate data manually. But it does not help in the above case, because
use_imm_date is ignored at handling the SRP login response. The problem is
definitely caused by a bug on the target side, but the initiator's
behavior also does not look correct. The initiator should not use
immediate data if use_imm_date is disabled by a user.
This commit adds an additional checking of use_imm_date at the handling of
SRP login response to avoid unexpected use of immediate data.
Fixes: 882981f4a4 ("RDMA/srp: Add support for immediate data")
Link: https://lore.kernel.org/r/20200115133055.30232-1-sergeygo@mellanox.com
Signed-off-by: Sergey Gorenko <sergeygo@mellanox.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Since ch has already been de-referenced by the time we get to the BUG_ON,
it is useless. The back trace alone is enough to tell what is going on,
delete the redundant BUG_ON.
Link: https://lore.kernel.org/r/20191217194437.25568-1-pakki001@umn.edu
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Danit Goldberg says:
====================
This series extends RTNETLINK to provide IB port and node GUIDs, which
were configured for Infiniband VFs.
The functionality to set VF GUIDs already existed for a long time, and
here we are adding the missing "get" so that netlink will be symmetric and
various cloud orchestration tools will be able to manage such VFs more
naturally.
The iproute2 was extended too to present those GUIDs.
- ip link show <device>
For example:
- ip link set ib4 vf 0 node_guid 22:44:33:00:33:11:00:33
- ip link set ib4 vf 0 port_guid 10:21:33:12:00:11:22:10
- ip link show ib4
ib4: <BROADCAST,MULTICAST> mtu 4092 qdisc noop state DOWN mode DEFAULT group default qlen 256
link/infiniband 00:00:0a:2d:fe:80:00:00:00:00:00:00:ec:0d:9a:03:00:44:36:8d brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
vf 0 link/infiniband 00:00:0a:2d:fe:80:00:00:00:00:00:00:ec:0d:9a:03:00:44:36:8d brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff,
spoof checking off, NODE_GUID 22:44:33:00:33:11:00:33, PORT_GUID 10:21:33:12:00:11:22:10, link-state disable, trust off, query_rss off
====================
Based on the mlx5-next branch from
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux for
dependencies
* branch 'ib-guids': (35 commits)
IB/mlx5: Implement callbacks for getting VFs GUID attributes
IB/ipoib: Add ndo operation for getting VFs GUID attributes
IB/core: Add interfaces to get VF node and port GUIDs
net/core: Add support for getting VF GUIDs
net/mlx5: Add new chain for netfilter flow table offload
net/mlx5: Refactor creating fast path prio chains
net/mlx5: Accumulate levels for chains prio namespaces
net/mlx5: Define fdb tc levels per prio
net/mlx5: Rename FDB_* tc related defines to FDB_TC_* defines
net/mlx5: Simplify fdb chain and prio eswitch defines
IB/mlx5: Load profile according to RoCE enablement state
IB/mlx5: Rename profile and init methods
net/mlx5: Handle "enable_roce" devlink param
net/mlx5: Document flow_steering_mode devlink param
devlink: Add new "enable_roce" generic device param
net/mlx5: fix spelling mistake "metdata" -> "metadata"
net/mlx5: fix kvfree of uninitialized pointer spec
IB/mlx5: Introduce and use mlx5_core_is_vf()
net/mlx5: E-switch, Enable metadata on own vport
net/mlx5: Refactor ingress acl configuration
...
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add ndo operation to the network driver that enables configuring
ipoib_get_vf_guid operation. The operation allows to get a VF port
and node GUIDs.
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The code added by this patch is similar to the code that already exists in
ibmvscsis_determine_resid(). This patch has been tested by running the
following command:
strace sg_raw -r 1k /dev/sdb 12 00 00 00 60 00 -o inquiry.bin |&
grep resid=
Link: https://lore.kernel.org/r/20191105214632.183302-1-bvanassche@acm.org
Fixes: a42d985bd5 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Honggang Li <honli@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Although the mentioned patch fixes a use-after-free bug, it introduces a
hang during shutdown. Since the latter is worse, revert this patch.
Link: https://lore.kernel.org/r/20191101204756.182162-1-bvanassche@acm.org
Reported-by: Honggang Li <honli@redhat.com>
Fixes: 9b64f7d0bb ("RDMA/srpt: Postpone HCA removal until after configfs directory removal")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Honggang Li <honli@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Unlike the iSCSI target driver, for the SRP target driver it is sufficient
if a single TPG can be associated with each RDMA port name. However, users
started associating multiple TPGs with RDMA port names. Support this by
converting the single TPG in struct srpt_port_id into a list. This patch
fixes the following list corruption issue:
list_add corruption. prev->next should be next (ffffffffc0a080c0), but was ffffa08a994ce6f0. (prev=ffffa08a994ce6f0).
WARNING: CPU: 2 PID: 2597 at lib/list_debug.c:28 __list_add_valid+0x6a/0x70
CPU: 2 PID: 2597 Comm: targetcli Not tainted 5.4.0-rc1.3bfa3c9602a7 #1
RIP: 0010:__list_add_valid+0x6a/0x70
Call Trace:
core_tpg_register+0x116/0x200 [target_core_mod]
srpt_make_tpg+0x3f/0x60 [ib_srpt]
target_fabric_make_tpg+0x41/0x290 [target_core_mod]
configfs_mkdir+0x158/0x3e0
vfs_mkdir+0x108/0x1a0
do_mkdirat+0x77/0xe0
do_syscall_64+0x55/0x1d0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Link: https://lore.kernel.org/r/20191023204106.23326-1-bvanassche@acm.org
Reported-by: Honggang LI <honli@redhat.com>
Fixes: a42d985bd5 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Honggang Li <honli@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add kernel-doc notation for missing function parameters:
../drivers/infiniband/ulp/iser/iser_initiator.c:365: warning: Function parameter or member 'conn' not described in 'iser_send_command'
../drivers/infiniband/ulp/iser/iser_initiator.c:365: warning: Function parameter or member 'task' not described in 'iser_send_command'
../drivers/infiniband/ulp/iser/iser_initiator.c:437: warning: Function parameter or member 'conn' not described in 'iser_send_data_out'
../drivers/infiniband/ulp/iser/iser_initiator.c:437: warning: Function parameter or member 'task' not described in 'iser_send_data_out'
../drivers/infiniband/ulp/iser/iser_initiator.c:437: warning: Function parameter or member 'hdr' not described in 'iser_send_data_out'
Link: https://lore.kernel.org/r/20191010035240.132033937@gmail.com
Signed-off-by: Randy Dunlap <rd.dunlab@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Various kernel-doc fixes:
- fix typos
- don't use /** for internal structs or functions
- fix Return: kernel-doc formatting
- add kernel-doc notation for missing function parameters
../drivers/infiniband/ulp/iser/iser_verbs.c:159: warning: Function parameter or member 'ib_conn' not described in 'iser_alloc_fmr_pool'
../drivers/infiniband/ulp/iser/iser_verbs.c:159: warning: Function parameter or member 'cmds_max' not described in 'iser_alloc_fmr_pool'
../drivers/infiniband/ulp/iser/iser_verbs.c:159: warning: Function parameter or member 'size' not described in 'iser_alloc_fmr_pool'
../drivers/infiniband/ulp/iser/iser_verbs.c:221: warning: Function parameter or member 'ib_conn' not described in 'iser_free_fmr_pool'
../drivers/infiniband/ulp/iser/iser_verbs.c:304: warning: Function parameter or member 'ib_conn' not described in 'iser_alloc_fastreg_pool'
../drivers/infiniband/ulp/iser/iser_verbs.c:304: warning: Function parameter or member 'cmds_max' not described in 'iser_alloc_fastreg_pool'
../drivers/infiniband/ulp/iser/iser_verbs.c:304: warning: Function parameter or member 'size' not described in 'iser_alloc_fastreg_pool'
../drivers/infiniband/ulp/iser/iser_verbs.c:338: warning: Function parameter or member 'ib_conn' not described in 'iser_free_fastreg_pool'
../drivers/infiniband/ulp/iser/iser_verbs.c:568: warning: Function parameter or member 'iser_conn' not described in 'iser_conn_release'
../drivers/infiniband/ulp/iser/iser_verbs.c:603: warning: Function parameter or member 'iser_conn' not described in 'iser_conn_terminate'
../drivers/infiniband/ulp/iser/iser_verbs.c:1040: warning: Function parameter or member 'signal' not described in 'iser_post_send'
../drivers/infiniband/ulp/iser/iser_verbs.c:1040: warning: Function parameter or member 'ib_conn' not described in 'iser_post_send'
../drivers/infiniband/ulp/iser/iser_verbs.c:1040: warning: Function parameter or member 'tx_desc' not described in 'iser_post_send'
Link: https://lore.kernel.org/r/20191010035240.070520193@gmail.com
Signed-off-by: Randy Dunlap <rd.dunlab@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix kernel-doc warnings (typos or renames) in ib_srpt.h:
../drivers/infiniband/ulp/srpt/ib_srpt.h:419: warning: Function parameter or member 'port_guid_id' not described in 'srpt_port'
../drivers/infiniband/ulp/srpt/ib_srpt.h:419: warning: Function parameter or member 'port_gid_id' not described in 'srpt_port'
Link: https://lore.kernel.org/r/20191010035239.950150496@gmail.com
Signed-off-by: Randy Dunlap <rd.dunlab@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Remove kernel-doc notation on 4 structs since they are internal and
none of the struct fields/members are described.
This removes 45 kernel-doc warnings.
Link: https://lore.kernel.org/r/20191010035239.818405496@gmail.com
Signed-off-by: Randy Dunlap <rd.dunlab@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix kernel-doc warnings and typos/spellos.
../drivers/infiniband/ulp/iser/iscsi_iser.h:254: warning: Function parameter or member 'dma_addr' not described in 'iser_tx_desc'
../drivers/infiniband/ulp/iser/iscsi_iser.h:254: warning: Function parameter or member 'cqe' not described in 'iser_tx_desc'
../drivers/infiniband/ulp/iser/iscsi_iser.h:254: warning: Function parameter or member 'reg_wr' not described in 'iser_tx_desc'
../drivers/infiniband/ulp/iser/iscsi_iser.h:254: warning: Function parameter or member 'send_wr' not described in 'iser_tx_desc'
../drivers/infiniband/ulp/iser/iscsi_iser.h:254: warning: Function parameter or member 'inv_wr' not described in 'iser_tx_desc'
../drivers/infiniband/ulp/iser/iscsi_iser.h:277: warning: Function parameter or member 'cqe' not described in 'iser_rx_desc'
../drivers/infiniband/ulp/iser/iscsi_iser.h:296: warning: Function parameter or member 'rsp' not described in 'iser_login_desc'
../drivers/infiniband/ulp/iser/iscsi_iser.h:339: warning: Function parameter or member 'reg_mem' not described in 'iser_reg_ops'
../drivers/infiniband/ulp/iser/iscsi_iser.h:399: warning: Function parameter or member 'all_list' not described in 'iser_fr_desc'
../drivers/infiniband/ulp/iser/iscsi_iser.h:413: warning: Function parameter or member 'all_list' not described in 'iser_fr_pool'
../drivers/infiniband/ulp/iser/iscsi_iser.h:439: warning: Function parameter or member 'reg_cqe' not described in 'ib_conn'
../drivers/infiniband/ulp/iser/iscsi_iser.h:491: warning: Function parameter or member 'snd_w_inv' not described in 'iser_conn'
This leaves 2 "member not described" warnings that I don't know how to fix:
../drivers/infiniband/ulp/iser/iscsi_iser.h:401: warning: Function parameter or member 'all_list' not described in 'iser_fr_desc'
../drivers/infiniband/ulp/iser/iscsi_iser.h:415: warning: Function parameter or member 'all_list' not described in 'iser_fr_pool'
Link: https://lore.kernel.org/r/20191010035239.756365352@gmail.com
Signed-off-by: Randy Dunlap <rd.dunlab@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix struct name in kernel-doc notation to match the struct name below it.
Fix one typo (spello).
Fix formatting as expected for kernel-doc notation.
Fix parameter name to match the function's parameter name to eliminate a
kernel-doc warning.
../drivers/infiniband/ulp/iser/iscsi_iser.c:815: warning: Function parameter or member 'non_blocking' not described in 'iscsi_iser_ep_connect'
Link: https://lore.kernel.org/r/20191010035239.623888112@gmail.com
Signed-off-by: Randy Dunlap <rd.dunlab@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Make sure all the debug prints in ib_iser module use the common driver
logger.
Link: https://lore.kernel.org/r/1570366580-24097-1-git-send-email-maxg@mellanox.com
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The default maximum immediate size is too big for old srp clients, which
do not support immediate data.
According to the SRP and SRP-2 specifications, the IOControllerProfile
attributes for SRP target ports contains the maximum initiator to target
iu length.
The maximum initiator to target iu length can be obtained by sending MAD
packets to query subnet manager port and SRP target ports. We should
calculate the max_it_iu_size instead of the default value, when remote
maximum initiator to target iu length available.
Link: https://lore.kernel.org/r/20190927174352.7800-2-honli@redhat.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Honggang Li <honli@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
According to SRP specifications 'srp-r16a' and 'srp2r06',
IOControllerProfile attributes for SRP target port include the maximum
initiator to target IU size.
SRP connection daemons, such as srp_daemon, can get the value from the
subnet manager. The SRP connection daemon can pass this value to kernel.
This patch adds a parse function for it.
Upstream commit [1] enables the kernel parameter, 'use_imm_data', by
default. [1] also use (8 * 1024) as the default value for kernel parameter
'max_imm_data'. With those default values, the maximum initiator to target
IU size will be 8260.
In case the SRPT modules, which include the in-tree 'ib_srpt.ko' module,
do not support SRP-2 'immediate data' feature, the default maximum
initiator to target IU size is significantly smaller than 8260. For
'ib_srpt.ko' module, which built from source before [2], the default
maximum initiator to target IU is 2116.
[1] introduces a regression issue for old srp targets with default kernel
parameters, as the connection will be rejected because of a too large
maximum initiator to target IU size.
[1] commit 882981f4a4 ("RDMA/srp: Add support for immediate data")
[2] commit 5dabcd0456 ("RDMA/srpt: Add support for immediate data")
Link: https://lore.kernel.org/r/20190927174352.7800-1-honli@redhat.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Honggang Li <honli@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Introduce a new data structure for the information about an RDMA port
name. This patch does not change any functionality.
Link: https://lore.kernel.org/r/20190930231707.48259-15-bvanassche@acm.org
Cc: Honggang LI <honli@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The current implementation does not wait until srpt_release_channel()
has finished and hence can trigger a use-after-free. Rework
srpt_release_sport() such that it waits until srpt_release_channel()
has finished. This patch fixes the following KASAN complaint:
==================================================================
BUG: KASAN: use-after-free in srpt_free_ioctx.part.23+0x42/0x100 [ib_srpt]
Read of size 8 at addr ffff888115c71100 by task kworker/4:3/807
CPU: 4 PID: 807 Comm: kworker/4:3 Not tainted 5.3.0-dbg+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Workqueue: events srpt_release_channel_work [ib_srpt]
Call Trace:
dump_stack+0x86/0xca
print_address_description+0x74/0x32d
__kasan_report.cold.6+0x1b/0x36
kasan_report+0x12/0x17
__asan_load8+0x54/0x90
srpt_free_ioctx.part.23+0x42/0x100 [ib_srpt]
srpt_free_ioctx_ring.part.24+0x50/0x80 [ib_srpt]
srpt_release_channel_work+0x2ad/0x390 [ib_srpt]
process_one_work+0x51a/0xa60
worker_thread+0x67/0x5b0
kthread+0x1dc/0x200
ret_from_fork+0x24/0x30
Allocated by task 984:
save_stack+0x21/0x90
__kasan_kmalloc.constprop.9+0xc7/0xd0
kasan_kmalloc+0x9/0x10
__kmalloc+0x153/0x370
srpt_add_one+0x4f/0x570 [ib_srpt]
add_client_context+0x251/0x290 [ib_core]
ib_register_client+0x1da/0x220 [ib_core]
iblock_get_alignment_offset_lbas+0x6b/0x100 [target_core_iblock]
do_one_initcall+0xcd/0x43a
do_init_module+0x103/0x380
load_module+0x3b77/0x3eb0
__do_sys_finit_module+0x12d/0x1b0
__x64_sys_finit_module+0x43/0x50
do_syscall_64+0x6b/0x2d0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 1128:
save_stack+0x21/0x90
__kasan_slab_free+0x139/0x190
kasan_slab_free+0xe/0x10
slab_free_freelist_hook+0x67/0x1e0
kfree+0xcb/0x2a0
srpt_remove_one+0x569/0x5b0 [ib_srpt]
remove_client_context+0x9a/0xe0 [ib_core]
disable_device+0x106/0x1b0 [ib_core]
__ib_unregister_device+0x5f/0xf0 [ib_core]
ib_unregister_device_and_put+0x48/0x60 [ib_core]
nldev_dellink+0x120/0x180 [ib_core]
rdma_nl_rcv+0x287/0x480 [ib_core]
netlink_unicast+0x2cc/0x370
netlink_sendmsg+0x3b1/0x630
__sys_sendto+0x1db/0x290
__x64_sys_sendto+0x80/0xa0
do_syscall_64+0x6b/0x2d0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff888115c71100
which belongs to the cache kmalloc-4k of size 4096
The buggy address is located 0 bytes inside of
4096-byte region [ffff888115c71100, ffff888115c72100)
The buggy address belongs to the page:
page:ffffea0004571c00 refcount:1 mapcount:0 mapping:ffff88811ac0de00 index:0xffff888115c70000 compound_mapcount: 0
flags: 0x2fff000000010200(slab|head)
raw: 2fff000000010200 ffffea00045ac408 ffffea0004593208 ffff88811ac0de00
raw: ffff888115c70000 0000000000070002 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888115c71000: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888115c71080: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff888115c71100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff888115c71180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff888115c71200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Link: https://lore.kernel.org/r/20190930231707.48259-14-bvanassche@acm.org
Cc: Honggang LI <honli@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Instead of relying on a waitqueue, report when the identity of an RDMA
channel can be reused through a completion.
Link: https://lore.kernel.org/r/20190930231707.48259-13-bvanassche@acm.org
Cc: Honggang LI <honli@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The ib_srpt driver uses two different identifiers while registering a
session with the LIO core. Report both identifiers if the modified
pr_debug() statement is enabled.
Link: https://lore.kernel.org/r/20190930231707.48259-12-bvanassche@acm.org
Cc: Honggang LI <honli@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The path_rec pointer is NULL set for IB and RoCE logins but not for iWARP
logins. Hence check the path_rec pointer before dereferencing it.
Link: https://lore.kernel.org/r/20190930231707.48259-11-bvanassche@acm.org
Cc: Honggang LI <honli@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Management datagrams (MADs) are not supported by SR-IOV VFs nor by iWARP
ports. Support SR-IOV VFs and iWARP ports by only logging an error message
if MAD handler registration fails.
Link: https://lore.kernel.org/r/20190930231707.48259-10-bvanassche@acm.org
Cc: Honggang LI <honli@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The IPv6 scope ID is essential when setting up an iWARP connection
between IPv6 link-local addresses. Report the scope ID in error messages.
Link: https://lore.kernel.org/r/20190930231707.48259-9-bvanassche@acm.org
Cc: Honggang LI <honli@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Instead of assuming that max_send_sge >= 3, restrict the number of scatter
gather elements to what is supported by the RDMA adapter.
Link: https://lore.kernel.org/r/20190930231707.48259-8-bvanassche@acm.org
Cc: Honggang LI <honli@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch does not change any functionality.
Link: https://lore.kernel.org/r/20190930231707.48259-7-bvanassche@acm.org
Cc: Honggang LI <honli@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In case we don't set the sg_prot_tablesize, the scsi layer assign the
default size (65535 entries). We should limit this size since we should
take into consideration the underlaying device capability. This cap is
considered when calculating the sg_tablesize. Otherwise, for example,
we can get that /sys/block/sdb/queue/max_segments is 128 and
/sys/block/sdb/queue/max_integrity_segments is 65535.
Link: https://lore.kernel.org/r/1569359027-10987-1-git-send-email-maxg@mellanox.com
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
ib_post_send, ib_post_recv and ib_dma_map_sg operations should succeed
unless something unusual happened to the ib device.
Link: https://lore.kernel.org/r/1569274369-29217-1-git-send-email-maxg@mellanox.com
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This cycle mainly saw lots of bug fixes and clean up code across the core
code and several drivers, few new functional changes were made.
- Many cleanup and bug fixes for hns
- Various small bug fixes and cleanups in hfi1, mlx5, usnic, qed,
bnxt_re, efa
- Share the query_port code between all the iWarp drivers
- General rework and cleanup of the ODP MR umem code to fit better with
the mmu notifier get/put scheme
- Support rdma netlink in non init_net name spaces
- mlx5 support for XRC devx and DC ODP
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEfB7FMLh+8QxL+6i3OG33FX4gmxoFAl2A1ugACgkQOG33FX4g
mxp+EQ//Ug8CyyDs40SGZztItoGghuQ4TVA2pXtuZ9LkFVJRWhYPJGOadHIYXqGO
KQJJpZPQ02HTZUPWBZNKmD5bwHfErm4cS73/mVmUpximnUqu/UsLRJp8SIGmBg1D
W1Lz1BJX24MdV8aUnChYvdL5Hbl52q+BaE99Z0haOvW7I3YnKJC34mR8m/A5MiRf
rsNIZNPHdq2U6pKLgCbOyXib8yBcJQqBb8x4WNAoB1h4MOx+ir5QLfr3ozrZs1an
xXgqyiOBmtkUgCMIpXC4juPN/6gw3Y5nkk2VIWY+MAY1a7jZPbI+6LJZZ1Uk8R44
Lf2KSzabFMMYGKJYE1Znxk+JWV8iE+m+n6wWEfRM9l0b4gXXbrtKgaouFbsLcsQA
CvBEQuiFSO9Kq01JPaAN1XDmhqyTarG6lHjXnW7ifNlLXnPbR1RJlprycExOhp0c
axum5K2fRNW2+uZJt+zynMjk2kyjT1lnlsr1Rbgc4Pyionaiydg7zwpiac7y/bdS
F7/WqdmPiff78KMi187EF5pjFqMWhthvBtTbWDuuxaxc2nrXSdiCUN+96j1amQUH
yU/7AZzlnKeKEQQCR4xddsSs2eTrXiLLFRLk9GCK2eh4cUN212eHTrPLKkQf1cN+
ydYbR2pxw3B38LCCNBy+bL+u7e/Tyehs4ynATMpBuEgc5iocTwE=
=zHXW
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull RDMA subsystem updates from Jason Gunthorpe:
"This cycle mainly saw lots of bug fixes and clean up code across the
core code and several drivers, few new functional changes were made.
- Many cleanup and bug fixes for hns
- Various small bug fixes and cleanups in hfi1, mlx5, usnic, qed,
bnxt_re, efa
- Share the query_port code between all the iWarp drivers
- General rework and cleanup of the ODP MR umem code to fit better
with the mmu notifier get/put scheme
- Support rdma netlink in non init_net name spaces
- mlx5 support for XRC devx and DC ODP"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (99 commits)
RDMA: Fix double-free in srq creation error flow
RDMA/efa: Fix incorrect error print
IB/mlx5: Free mpi in mp_slave mode
IB/mlx5: Use the original address for the page during free_pages
RDMA/bnxt_re: Fix spelling mistake "missin_resp" -> "missing_resp"
RDMA/hns: Package operations of rq inline buffer into separate functions
RDMA/hns: Optimize cmd init and mode selection for hip08
IB/hfi1: Define variables as unsigned long to fix KASAN warning
IB/{rdmavt, hfi1, qib}: Add a counter for credit waits
IB/hfi1: Add traces for TID RDMA READ
RDMA/siw: Relax from kmap_atomic() use in TX path
IB/iser: Support up to 16MB data transfer in a single command
RDMA/siw: Fix page address mapping in TX path
RDMA: Fix goto target to release the allocated memory
RDMA/usnic: Avoid overly large buffers on stack
RDMA/odp: Add missing cast for 32 bit
RDMA/hns: Use devm_platform_ioremap_resource() to simplify code
Documentation/infiniband: update name of some functions
RDMA/cma: Fix false error message
RDMA/hns: Fix wrong assignment of qp_access_flags
...
Maximum supported IO size is 8MB for the iSER driver. The current value is
limited by the ISCSI_ISER_MAX_SG_TABLESIZE macro. But the driver is able
to handle 16MB IOs without any significant changes. Increasing this limit
can be useful for the storage arrays which are fine tuned for IOs larger
than 8 MB.
This commit allows to configure maximum IO size up to 16MB using the
max_sectors module parameter.
Link: https://lore.kernel.org/r/20190912103534.18210-1-sergeygo@mellanox.com
Signed-off-by: Sergey Gorenko <sergeygo@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Send and Receive completion is handled on a single CPU selected at
the time each Completion Queue is allocated. Typically this is when
an initiator instantiates an RDMA transport, or when a target
accepts an RDMA connection.
Some ULPs cannot open a connection per CPU to spread completion
workload across available CPUs and MSI vectors. For such ULPs,
provide an API that allows the RDMA core to select a completion
vector based on the device's complement of available comp_vecs.
ULPs that invoke ib_alloc_cq() with only comp_vector 0 are converted
to use the new API so that their completion workloads interfere less
with each other.
Suggested-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Cc: <linux-cifs@vger.kernel.org>
Cc: <v9fs-developer@lists.sourceforge.net>
Link: https://lore.kernel.org/r/20190729171923.13428.52555.stgit@manet.1015granger.net
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note
is adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXTJS/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQTNAQCsTdkA
IN1BvDBbE+KO8mvL5DuRxLtnDU6Pq5K6fkrE3gD/a1GkqyPPaJIuspq7fQY87DH/
o7VsJd/5uGphIE2Ls+M=
=38XV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note is
adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: megaraid_sas: set an unlimited max_segment_size
scsi: mpt3sas: set an unlimited max_segment_size for SAS 3.0 HBAs
scsi: IB/srp: set virt_boundary_mask in the scsi host
scsi: IB/iser: set virt_boundary_mask in the scsi host
scsi: storvsc: set virt_boundary_mask in the scsi host template
scsi: ufshcd: set max_segment_size in the scsi host template
scsi: core: take the DMA max mapping size into account
scsi: core: add a host / host template field for the virt boundary
scsi: core: Fix race on creating sense cache
scsi: sd_zbc: Fix compilation warning
scsi: libfc: fix null pointer dereference on a null lport
scsi: zfcp: fix GCC compiler warning emitted with -Wmaybe-uninitialized
scsi: zfcp: fix request object use-after-free in send path causing wrong traces
scsi: zfcp: fix request object use-after-free in send path causing seqno errors
scsi: megaraid_sas: Update driver version to 07.710.50.00
scsi: megaraid_sas: Add module parameter for FW Async event logging
scsi: megaraid_sas: Enable msix_load_balance for Invader and later controllers
scsi: megaraid_sas: Fix calculation of target ID
scsi: lpfc: reduce stack size with CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE
scsi: devinfo: BLIST_TRY_VPD_PAGES for SanDisk Cruzer Blade
...
This ensures all proper DMA layer handling is taken care of by the SCSI
midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This ensures all proper DMA layer handling is taken care of by the SCSI
midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A smaller cycle this time. Notably we see another new driver, 'Soft
iWarp', and the deletion of an ancient unused driver for nes.
- Revise and simplify the signature offload RDMA MR APIs
- More progress on hoisting object allocation boiler plate code out of the
drivers
- Driver bug fixes and revisions for hns, hfi1, efa, cxgb4, qib, i40iw
- Tree wide cleanups: struct_size, put_user_page, xarray, rst doc conversion
- Removal of obsolete ib_ucm chardev and nes driver
- netlink based discovery of chardevs and autoloading of the modules
providing them
- Move more of the rdamvt/hfi1 uapi to include/uapi/rdma
- New driver 'siw' for software based iWarp running on top of netdev,
much like rxe's software RoCE.
- mlx5 feature to report events in their raw devx format to userspace
- Expose per-object counters through rdma tool
- Adaptive interrupt moderation for RDMA (DIM), sharing the DIM core
from netdev
-----BEGIN PGP SIGNATURE-----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=iWcG
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A smaller cycle this time. Notably we see another new driver, 'Soft
iWarp', and the deletion of an ancient unused driver for nes.
- Revise and simplify the signature offload RDMA MR APIs
- More progress on hoisting object allocation boiler plate code out
of the drivers
- Driver bug fixes and revisions for hns, hfi1, efa, cxgb4, qib,
i40iw
- Tree wide cleanups: struct_size, put_user_page, xarray, rst doc
conversion
- Removal of obsolete ib_ucm chardev and nes driver
- netlink based discovery of chardevs and autoloading of the modules
providing them
- Move more of the rdamvt/hfi1 uapi to include/uapi/rdma
- New driver 'siw' for software based iWarp running on top of netdev,
much like rxe's software RoCE.
- mlx5 feature to report events in their raw devx format to userspace
- Expose per-object counters through rdma tool
- Adaptive interrupt moderation for RDMA (DIM), sharing the DIM core
from netdev"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (194 commits)
RMDA/siw: Require a 64 bit arch
RDMA/siw: Mark expected switch fall-throughs
RDMA/core: Fix -Wunused-const-variable warnings
rdma/siw: Remove set but not used variable 's'
rdma/siw: Add missing dependencies on LIBCRC32C and DMA_VIRT_OPS
RDMA/siw: Add missing rtnl_lock around access to ifa
rdma/siw: Use proper enumerated type in map_cqe_status
RDMA/siw: Remove unnecessary kthread create/destroy printouts
IB/rdmavt: Fix variable shadowing issue in rvt_create_cq
RDMA/core: Fix race when resolving IP address
RDMA/core: Make rdma_counter.h compile stand alone
IB/core: Work on the caller socket net namespace in nldev_newlink()
RDMA/rxe: Fill in wc byte_len with IB_WC_RECV_RDMA_WITH_IMM
RDMA/mlx5: Set RDMA DIM to be enabled by default
RDMA/nldev: Added configuration of RDMA dynamic interrupt moderation to netlink
RDMA/core: Provide RDMA DIM support for ULPs
linux/dim: Implement RDMA adaptive moderation (DIM)
IB/mlx5: Report correctly tag matching rendezvous capability
docs: infiniband: add it to the driver-api bookset
IB/mlx5: Implement VHCA tunnel mechanism in DEVX
...
This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTl4yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdcxAQDCJVbd
fPUX76/V1ldupunF97+3DTharxxbst+VnkOnCwD8D4c0KFFFOI9+F36cnMGCPegE
fjy17dQLvsJ4GsidHy8=
=aS5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
Despite failure in ipoib_dev_init() we continue with initialization flow
and creation of child device. It causes to the situation where this child
device is added too early to parent device list.
Change the logic, so in case of failure we properly return error from
ipoib_dev_init() and add child only in success path.
Fixes: eaeb398425 ("IB/ipoib: Move init code to ndo_init")
Signed-off-by: Valentine Fatiev <valentinef@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
vzalloc has already zeroed the memory. So a memset is unneeded.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Os1seHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGtx4H/j6i482XzcGFKTBm
A7mBoQpy+kLtoUov4EtBAR62OuwI8rsahW9di37QKndPoQrczWaKBmr3De6LCdPe
v3pl3O6wBbvH5ru+qBPFX9PdNbDvimEChh7LHxmMxNQq3M+AjZAZVJyfpoiFnx35
Fbge+LZaH/k8HMwZmkMr5t9Mpkip715qKg2o9Bua6dkH0AqlcpLlC8d9a+HIVw/z
aAsyGSU8jRwhoAOJsE9bJf0acQ/pZSqmFp0rDKqeFTSDMsbDRKLGq/dgv4nW0RiW
s7xqsjb/rdcvirRj3rv9+lcTVkOtEqwk0PVdL9WOf7g4iYrb3SOIZh8ZyViaDSeH
VTS5zps=
=huBY
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc6' into rdma.git for-next
For dependencies in next patches.
Resolve conflicts:
- Use uverbs_get_cleared_udata() with new cq allocation flow
- Continue to delete nes despite SPDX conflict
- Resolve list appends in mlx5_command_str()
- Use u16 for vport_rule stuff
- Resolve list appends in struct ib_client
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The InfiniBand docs are plain text with no markups. So, all we needed to
do were to add the title markups and some markup sequences in order to
properly parse tables, lists and literal blocks.
At its new index.rst, let's add a :orphan: while this is not linked to the
main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Replace the old signature handover API with the new one. The new API
simplifes PI handover code complexity for ULPs and improve performance.
For RW API it will reduce the maximum number of work requests per task
and the need of dealing with multiple MRs (and their registrations and
invalidations) per task. All the mappings and registration of the data
and the protection buffers is done by the LLD using a single WR and a
special MR type (IB_MR_TYPE_INTEGRITY) for the PI handover operation.
The setup of the tested benchmark (using iSER ULP):
- 2 servers with 24 cores (1 initiator and 1 target)
- ConnectX-4/ConnectX-5 adapters
- 24 target sessions with 1 LUN each
- ramdisk backstore
- PI active
Performance results running fio (24 jobs, 128 iodepth) using
write_generate=1 and read_verify=1 (w/w.o patch):
bs IOPS(read) IOPS(write)
---- ---------- ----------
512 1243.3K/1182.3K 1725.1K/1680.2K
4k 571233/528835 743293/748259
32k 72388/71086 71789/93573
Using write_generate=0 and read_verify=0 (w/w.o patch):
bs IOPS(read) IOPS(write)
---- ---------- ----------
512 1572.1K/1427.2K 1823.5K/1724.3K
4k 921992/916194 753772/768267
32k 75052/73960 73180/95484
There is a performance degradation when writing big block sizes.
Degradation is caused by the complexity of combining multiple
indirections and perform RDMA READ operation from it. This will be
fixed in the following patches by reducing the indirections if
possible.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Rename IB_QP_CREATE_SIGNATURE_EN to IB_QP_CREATE_INTEGRITY_EN
and IB_DEVICE_SIGNATURE_HANDOVER to IB_DEVICE_INTEGRITY_HANDOVER.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
After decreasing WRs array size from 7 to 3 it is more
readable to give each WR a descriptive name.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Using this new API reduces iSER code complexity.
It also reduces the maximum number of work requests per task and the need
of dealing with multiple MRs (and their registrations and invalidations)
per task. It is done by using a single WR and a special MR type
(IB_MR_TYPE_INTEGRITY) for PI operation.
The setup of the tested benchmark:
- 2 servers with 24 cores (1 initiator and 1 target)
- 24 target sessions with 1 LUN each
- ramdisk backstore
- PI active
Performance results running fio (24 jobs, 128 iodepth) using
write_generate=0 and read_verify=0 (w/w.o patch):
bs IOPS(read) IOPS(write)
---- ---------- ----------
512 1236.6K/1164.3K 1357.2K/1332.8K
1k 1196.5K/1163.8K 1348.4K/1262.7K
2k 1016.7K/921950 1003.7K/931230
4k 662728/600545 595423/501513
8k 385954/384345 333775/277090
16k 222864/222820 170317/170671
32k 116869/114896 82331/82244
64k 55205/54931 40264/40021
Using write_generate=1 and read_verify=1 (w/w.o patch):
bs IOPS(read) IOPS(write)
---- ---------- ----------
512 1090.1K/1030.9K 1303.9K/1101.4K
1k 1057.7K/904583 1318.4K/988085
2k 965226/638799 1008.6K/692514
4k 555479/410151 542414/414517
8k 298675/224964 264729/237508
16k 133485/122481 164625/138647
32k 74329/67615 80143/78743
64k 35716/35519 39294/37334
We get performance improvement at all block sizes.
The most significant improvement is when writing 4k bs (almost 30% more
iops).
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The previous patch guarantees that srp_queuecommand() does not get
invoked while reconnecting occurs. Hence remove the code from
srp_queuecommand() that prevents command queueing while reconnecting.
This patch avoids that the following can appear in the kernel log:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:747
in_atomic(): 1, irqs_disabled(): 0, pid: 5600, name: scsi_eh_9
1 lock held by scsi_eh_9/5600:
#0: (rcu_read_lock){....}, at: [<00000000cbb798c7>] __blk_mq_run_hw_queue+0xf1/0x1e0
Preemption disabled at:
[<00000000139badf2>] __blk_mq_delay_run_hw_queue+0x78/0xf0
CPU: 9 PID: 5600 Comm: scsi_eh_9 Tainted: G W 4.15.0-rc4-dbg+ #1
Hardware name: Dell Inc. PowerEdge R720/0VWT90, BIOS 2.5.4 01/22/2016
Call Trace:
dump_stack+0x67/0x99
___might_sleep+0x16a/0x250 [ib_srp]
__mutex_lock+0x46/0x9d0
srp_queuecommand+0x356/0x420 [ib_srp]
scsi_dispatch_cmd+0xf6/0x3f0
scsi_queue_rq+0x4a8/0x5f0
blk_mq_dispatch_rq_list+0x73/0x440
blk_mq_sched_dispatch_requests+0x109/0x1a0
__blk_mq_run_hw_queue+0x131/0x1e0
__blk_mq_delay_run_hw_queue+0x9a/0xf0
blk_mq_run_hw_queue+0xc0/0x1e0
blk_mq_start_hw_queues+0x2c/0x40
scsi_run_queue+0x18e/0x2d0
scsi_run_host_queues+0x22/0x40
scsi_error_handler+0x18d/0x5f0
kthread+0x11c/0x140
ret_from_fork+0x24/0x30
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
in the case of IPoIB with SRIOV enabled hardware
ip link show command incorrecly prints
0 instead of a VF hardware address.
Before:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 256
link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
vf 0 MAC 00:00:00:00:00:00, spoof checking off, link-state disable,
trust off, query_rss off
...
After:
11: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 256
link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
vf 0 link/infiniband
80:00:00:66:fe:80:00:00:00:00:00:00:24:8a:07:03:00:a4:3e:7c brd
00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff, spoof
checking off, link-state disable, trust off, query_rss off
v1->v2: just copy an address without modifing ifla_vf_mac
v2->v3: update the changelog
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default action for unlisted tests is "not-supported", so given that
ipoib doesn't support ETH_SS_TEST, there is no need to check for it
in the case statements, just let it get caught by the default: case.
Fixes: e3614bc9dc ("IB/ipoib: Add readout of statistics using ethtool")
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The function srp_parse_in() is used both for parsing source address
specifications and for target address specifications. Target addresses
must have a port number. Having to specify a port number for source
addresses is inconvenient. Make sure that srp_parse_in() supports again
parsing addresses with no port number.
Cc: <stable@vger.kernel.org>
Fixes: c62adb7def ("IB/srp: Fix IPv6 address parsing")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add support for reporting link state for ipoib net devices.
$ ip l set dev mlx4_ib0 up
$ ethtool mlx4_ib0 | grep Link
Link detected: yes
$ ip l set dev mlx4_ib0 down
$ ethtool mlx4_ib0 | grep Link
Link detected: no
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The usual driver bug fixes and fixes for a couple of regressions introduced in
5.2:
- Fix a race on bootup with RDMA device renaming and srp. SRP also needs to
rename its internal sys files
- Fix a memory leak in hns
- Don't leak resources in efa on certain error unwinds
- Don't panic in certain error unwinds in ib_register_device
- Various small user visible bug fix patches for the hfi and efa drivers
- Fix the 32 bit compilation break
-----BEGIN PGP SIGNATURE-----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=RmxY
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Things are looking pretty quiet here in RDMA, not too many bug fixes
rolling in right now. The usual driver bug fixes and fixes for a
couple of regressions introduced in 5.2:
- Fix a race on bootup with RDMA device renaming and srp. SRP also
needs to rename its internal sys files
- Fix a memory leak in hns
- Don't leak resources in efa on certain error unwinds
- Don't panic in certain error unwinds in ib_register_device
- Various small user visible bug fix patches for the hfi and efa
drivers
- Fix the 32 bit compilation break"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/efa: Remove MAYEXEC flag check from mmap flow
mlx5: avoid 64-bit division
IB/hfi1: Validate page aligned for a given virtual address
IB/{qib, hfi1, rdmavt}: Correct ibv_devinfo max_mr value
IB/hfi1: Insure freeze_work work_struct is canceled on shutdown
IB/rdmavt: Fix alloc_qpn() WARN_ON()
RDMA/core: Fix panic when port_data isn't initialized
RDMA/uverbs: Pass udata on uverbs error unwind
RDMA/core: Clear out the udata before error unwind
RDMA/hns: Fix PD memory leak for internal allocation
RDMA/srp: Rename SRP sysfs name after IB device rename trigger
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are nothing to do from user side with knowledge that destroy CQ
fails.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
SRP logic used device name and port index as symlink to relevant
kobject. If the IB device is renamed then the prior name will be re-used
by the next device plugged in and sysfs will panic as SRP will try to
re-use the same name.
mlx5_ib: Mellanox Connect-IB Infiniband driver v5.0-0
sysfs: cannot create duplicate filename '/class/infiniband_srp/srp-mlx5_0-1'
CPU: 3 PID: 1107 Comm: modprobe Not tainted 5.1.0-for-upstream-perf-2019-05-12_15-09-52-87 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
Call Trace:
dump_stack+0x5a/0x73
sysfs_warn_dup+0x58/0x70
sysfs_do_create_link_sd.isra.2+0xa3/0xb0
device_add+0x33f/0x660
srp_add_one+0x301/0x4f0 [ib_srp]
add_client_context+0x99/0xe0 [ib_core]
enable_device_and_get+0xd1/0x1b0 [ib_core]
ib_register_device+0x533/0x710 [ib_core]
? mutex_lock+0xe/0x30
__mlx5_ib_add+0x23/0x70 [mlx5_ib]
mlx5_add_device+0x4e/0xd0 [mlx5_core]
mlx5_register_interface+0x85/0xc0 [mlx5_core]
? 0xffffffffa0791000
do_one_initcall+0x4b/0x1cb
? kmem_cache_alloc_trace+0xc6/0x1d0
? do_init_module+0x22/0x21f
do_init_module+0x5a/0x21f
load_module+0x17f2/0x1ca0
? m_show+0x1c0/0x1c0
__do_sys_finit_module+0x94/0xe0
do_syscall_64+0x48/0x120
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f157cce10d9
The module load/unload sequence was used to trigger such kernel panic:
sudo modprobe ib_srp
sudo modprobe -r mlx5_ib
sudo modprobe -r mlx5_core
sudo modprobe mlx5_core
Have SRP track the name of the core device so that it can't have a name
collision.
Fixes: d21943dd19 ("RDMA/core: Implement IB device rename function")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reduce lines of code by using local variable.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has been a smaller cycle than normal. One new driver was accepted,
which is unusual, and at least one more driver remains in review on the
list.
- Driver fixes for hns, hfi1, nes, rxe, i40iw, mlx5, cxgb4, vmw_pvrdma
- Many patches from MatthewW converting radix tree and IDR users to use
xarray
- Introduction of tracepoints to the MAD layer
- Build large SGLs at the start for DMA mapping and get the driver to
split them
- Generally clean SGL handling code throughout the subsystem
- Support for restricting RDMA devices to net namespaces for containers
- Progress to remove object allocation boilerplate code from drivers
- Change in how the mlx5 driver shows representor ports linked to VFs
- mlx5 uapi feature to access the on chip SW ICM memory
- Add a new driver for 'EFA'. This is HW that supports user space packet
processing through QPs in Amazon's cloud
-----BEGIN PGP SIGNATURE-----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=TS64
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a smaller cycle than normal. One new driver was
accepted, which is unusual, and at least one more driver remains in
review on the list.
Summary:
- Driver fixes for hns, hfi1, nes, rxe, i40iw, mlx5, cxgb4,
vmw_pvrdma
- Many patches from MatthewW converting radix tree and IDR users to
use xarray
- Introduction of tracepoints to the MAD layer
- Build large SGLs at the start for DMA mapping and get the driver to
split them
- Generally clean SGL handling code throughout the subsystem
- Support for restricting RDMA devices to net namespaces for
containers
- Progress to remove object allocation boilerplate code from drivers
- Change in how the mlx5 driver shows representor ports linked to VFs
- mlx5 uapi feature to access the on chip SW ICM memory
- Add a new driver for 'EFA'. This is HW that supports user space
packet processing through QPs in Amazon's cloud"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (186 commits)
RDMA/ipoib: Allow user space differentiate between valid dev_port
IB/core, ipoib: Do not overreact to SM LID change event
RDMA/device: Don't fire uevent before device is fully initialized
lib/scatterlist: Remove leftover from sg_page_iter comment
RDMA/efa: Add driver to Kconfig/Makefile
RDMA/efa: Add the efa module
RDMA/efa: Add EFA verbs implementation
RDMA/efa: Add common command handlers
RDMA/efa: Implement functions that submit and complete admin commands
RDMA/efa: Add the ABI definitions
RDMA/efa: Add the com service API definitions
RDMA/efa: Add the efa_com.h file
RDMA/efa: Add the efa.h header file
RDMA/efa: Add EFA device definitions
RDMA: Add EFA related definitions
RDMA/umem: Remove hugetlb flag
RDMA/bnxt_re: Use core helpers to get aligned DMA address
RDMA/i40iw: Use core helpers to get aligned DMA address within a supported page size
RDMA/verbs: Add a DMA iterator to return aligned contiguous memory blocks
RDMA/umem: Add API to find best driver supported page size in an MR
...
Systemd triggers the following warning during IPoIB device load:
mlx5_core 0000:00:0c.0 ib0: "systemd-udevd" wants to know my dev_id.
Should it look at dev_port instead?
See Documentation/ABI/testing/sysfs-class-net for more info.
This is caused due to user space attempt to differentiate old systems
without dev_port and new systems with dev_port. In case dev_port will be
zero, the systemd will try to read dev_id instead.
There is no need to print a warning in such case, because it is valid
situation and it is needed to ensure systemd compatibility with old
kernels.
Link: https://github.com/systemd/systemd/blob/master/src/udev/udev-builtin-net_id.c#L358
Cc: <stable@vger.kernel.org> # 4.19
Fixes: f6350da41d ("IB/ipoib: Log sysfs 'dev_id' accesses from userspace")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When IPoIB receives an SM LID change event, it reacts by flushing its
path record cache and rejoining multicast groups. This is the same
behavior it performs when it receives a reregistration event. This
behavior is unnecessary as an SM may have database backup or
synchronization mechanisms which permit the SM location or LID to change
without loss of multicast membership and without impact to path records.
Both opensm and the OPA FM issue reregistration events if a new SM is
started (or restarted with a new config) or an SM event occurs which
results in loss of multicast membership records by the SM (such as
opensm failover) or the SM encounters new nodes with Active ports (such
as after joining 2 fabrics by connecting switches via ISLs). Hence this
event can be depended on as the trigger for IPoIB cache and multicast
flushing.
It appears that some drivers, such as qib, and hfi1 issue the
IB_EVENT_SM_CHANGE but other drivers such as mlx4 and mlx5 do not.
Empirical testing on Mellanox EDR using ibv_asyncwatch has confirmed
that Mellanox EDR HCAs do not generate SM change events and that opensm
does generate reregistration.
An SM LID change event is generated by the mentioned drivers to reflect
that sm_lid and/or sm_sl in the local port info has changed. The intent
of this event is to permit applications and ULPs which have a local copy
of this information (or an address handle using it) to update their
information.
The intent is that the reregistration event (caused by the SM via a bit
in Set(PortInfo)) be used to inform nodes that they need to rejoin
multicast groups, resubscribe for notices and potentially update path
records.
When an SM migrates or fails over, a SM LID change event can occur. In
response IPoIB discards path records and multicast membership and loses
connectivity until these records are restored via SA requests. In very
large fabrics, it may take minutes for the SM to be ready and for the SA
responses to be supplied. This can result in undesirable and
unnecessary IPoIB connectivity impacts. It also can result in an
unnecessary storm of SA queries from all nodes in a cluster potentially
followed by yet another storm if the SM issues the reregistration
request.
The fact the Mellanox HCAs do not even generate this event, is further
evidence that on modern IB fabrics there will be no ill side effects
from the proposed changes below to reduce the reaction by 3 kernel
components to this event. So these changes should be benign for Mellanox
IB fabrics and will benefit OPA fabrics while also making ib_core and
ULP behavor "correct" as intended by the IBTA spec and kernel RDMA event
APIs.
Address these issues by removing IB_EVENT_SM_CHANGE handling from ipoib.
IPoIB does not locally store sm_lid nor sm_sl, so it does not need to do
anything on SM LID change. IPoIB makes use of other ib_core components
to issue SA requests for it and those components correctly track SM LID
and SM LID changes.
Also in ib_core multicast handling, remove the test for
IB_EVENT_SM_CHANGE. This code is moving all multicast groups to the
error state, which will trigger rejoins. This code is used by IPoIB as
well as the connection manager and other clients of multicast groups.
This kernel module centralizes group membership status and joins since a
node can only join a given group once but multiple ULPs or applications
may want to join the same group. It makes use of the sa_query.c
component in ib_core, which correctly trackes SM LID and SL. This
component does not track SM LID nor SL itself and hence need not react
to their changes.
Similarly in the ib_core cache code remove the handling for the
IB_EVENT_SM_CHANGE. In this function. The ib_cache_update function
which is ultimately called is updating local copies of the pkey table,
gid table and lmc. It does not update nor retain sm_lid nor sm_sl. As
such it does not need to be called on an SM LID change. It technically
also does not need to be called on a reregistration. The LID_CHANGE,
PKEY_CHANGE, GID_CHANGE and port state change events (PORT_ERR,
PORT_ACTICE) should be sufficient triggers.
It is worth noting that the alternative of simply having the hfi1 and
qib drivers not generate the SM LID change event was explored. While
this would duplicate what Mellanox drivers do now, it is not the correct
behavior and removes the ability for an SM to migrate without requiring
reregistration. Since both opensm and OPA SM have mechanisms to backup
or synchronize registration information, it is desirable to let them
perform SM migrations (with LID or SL changes) without requiring
reregistration when they deem it appropriate.
Suggested-by: Todd Rimmer <todd.rimmer@intel.com>
Tested-by: Michael Brooks <michael.brooks@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Todd Rimmer <todd.rimmer@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The check on record->event is always true because the wrong operator
is being used, used && instead of ||
Addresses-Coverity: ("Constant expression result")
Fixes: fae7a699a9 ("opa_vnic: Convert vport_idr to XArray")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The variable len is not being inintialized and the uninitialized value is
being returned. However, this return path is never reached because the
default case in the switch statement returns -ENOSYS. Clean up the code
by replacing the return -ENOSYS with a break for the default case and
returning -ENOSYS at the end of the function. This allows len to be
removed. Also remove redundant break that follows a return statement.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Adjust the kconfig whitespace in bnxt_re/iser to match the kernel
standard.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
"__attribute__" set of macros has been standardized, have became more
potentially portable and consistent code back in v2.6.21 by commit
82ddcb040 ("[PATCH] extend the set of "__attribute__" shortcut macros").
Moreover, nowadays checkpatch.pl warns about using __attribute__((packed))
instead of __packed.
This patch converts all the "__attribute__ ((packed))" annotations to
"__packed" within the RDMA subsystem.
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.
We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.
Tested with ixgbe and CONFIG_FCOE=m
With pktgen using queue xmit:
threads vanilla patched
(kpps) (kpps)
1 2334 2428
2 4166 4278
4 7895 8100
v1 -> v2:
- rebased after helper's name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wan Jiabing