Update the sh7372 clock code to set the RT side
set of MSTP bits to a fixed disabled state.
The sh7372 SoC contains two sets of MSTP bits,
one for the ARM (SYS) side, and one for the
SH4AL-DSP (RT) side. The actual clock associated
with the MSTP bit will only be stopped when both
sides have set the MSTP bit to disabled mode.
Some MSTP bits are enabled by default after
hardware reset, so this patch adjusts the code
to disable all MSTP bits associated with the RT
side to allow the SYS side to have full control.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The PLLC2 clock on AP4 systems does not need to run constantly to be
able to use HDMI. The HDMI hotplug interrupt works without the PLL
too, after which all the necessary clocks will be turned on by the
runtime PM.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add DMA mode support for the MMCIF controller on mackerel.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remember to also check for the CONFIG_MMC_SH_MMCIF_MODULE option
for the case of a modular MMCIF driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the following sh7377 multimedia hardware blocks
using UIO: VPU, VEU[0-3], JPU and SPU2[0-1]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the following sh7372 multimedia hardware blocks
using UIO: VPU, VEU[0-3], JPU and SPU2[0-1]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the following sh7367 multimedia hardware blocks
using UIO: VPU, VEU[0-3], VEU2H, JPU and SPU1
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7377 serial port types to make use of
PORT_SCIFA and PORT_SCIFB. This makes the software
match the sh7377 data sheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* Set receive enable and transmit enable bits of SCASCR0 (E6C400089).
Values previously written to this register was bogus.
Curiously earlyprintk works with the previous code.
* Remove duplicate initialisation of GPIO port 152, SCIFA0_TXD (0xE6053098).
This should have no effect other than to very slightly reduce the amount of
code.
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
ARM: bcmring: convert to use sp804 clockevents
ARM: bcmring: convert to sp804 clocksource
ARM: 6912/1: bcmring: Add clkdev table in init_early
clockevents: ARM sp804: obtain sp804 timer rate via clks
clockevents: ARM sp804: allow clockevent name to be specified
clocksource: ARM sp804: obtain sp804 timer rate via clks
clocksource: ARM sp804: allow clocksource name to be specified
clocksource: convert OMAP1 to 32-bit down counting clocksource
clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
clocksource: convert SPEAr platforms 16-bit up counting clocksource
clocksource: convert Integrator/AP 16-bit down counting clocksource
clocksource: convert W90x900 24-bit down counting clocksource
clocksource: convert ARM 32-bit down counting clocksources
clocksource: convert ARM 32-bit up counting clocksources
clocksource: add common mmio clocksource
ARM: update sa1100 to reflect PXA updates
ARM: omap1: convert to using readl/writel instead of volatile struct
ARM: omap1: delete useless interrupt handler
ARM: s5p: consolidate selection of timer register
ARM: 6939/1: fix missing 'cpu_relax()' declaration
...
This patch adds a driver for the hardware time stamping unit found on the
IXP465. The basic clock operations and an external trigger are implemented.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: John Stultz <john.stultz@linaro.org>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
bcmring has a set of four sp804 timers incorporated, yet it has its
own copy of the sp804 code. Convert its clockevent implementation
to the standard sp804 support code.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
bcmring has a set of four sp804 timers incorporated, yet it has its
own copy of the sp804 code. Convert its clocksource implementation
to the standard sp804 support code.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move adding clkdev table to init_early to make sure the common sp804 clockevents can be initialized properly.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows platforms to specify the rate of the SP804 clockevent via
the clk subsystem. While ARM boards clock these at 1MHz, BCMRing also
has SP804 timers but are clocked at different rates.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows platforms to specify the clcokevent name upon registration.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows platforms to specify the rate of the SP804 clocksource via
the clk subsystem. While ARM boards clock these at 1MHz, BCMRing also
has SP804 timers but are clocked at different rates.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows platforms to specify the clocksource name upon
registration, which is necessary should they wish to register more
than one sp804 clocksource.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the OMAP1 32-bit down counting clocksource to the generic
clocksource infrastructure.
Tested-by: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the MXS timrotv2 32-bit down counting clocksource to the
generic clocksource infrastructure.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert SPEAr platforms 16-bit up counting clocksource, which requires
a 16-bit register access read rather than 32-bit.
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the Integrator/AP 16-bit down-counting clocksource to the
generic clocksource infrastructure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the W90x900 24-bit down-counting clocksource to the generic
mmio clocksource infrastructure
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert ixp4xx, lpc32xx, mxc, netx, pxa, sa1100, tcc8k, tegra and u300
to use the generic mmio clocksource recently introduced.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update sa1100 clockevents code to reflect what its later derivative
does with clockevents_calc_mult_shift(). Use OSSR_M* constants too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The OMAP1 clocksource interrupt handler just increments a variable
which otherwise isn't used, so this seems to be unnecessary. Tony
Lindgren confirms, so lets remove it.
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
s5p duplicates the runtime selection of the timer register three times.
Move this out into a separate function.
FIXME: It is unclear whether this code needs to support true runtime
selection of the timer register, or whether it can be selected once at
init time.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the definition of DM64XX_VDD3P3V_PWDN from hardware.h
to devices.c since it is used only there.
This also helps rid hardware.h of platform private stuff.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
ARM build fails with the following symptom:
CC arch/arm/kernel/asm-offsets.s
In file included from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:57,
from arch/arm/kernel/asm-offsets.c:13:
include/linux/spinlock.h: In function 'spin_unlock_wait':
include/linux/spinlock.h:360: error: implicit declaration of function 'cpu_relax'
make[1]: *** [arch/arm/kernel/asm-offsets.s] Error 1
Fix it by including <asm/processor.h>.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Commit e2a083dc0da9aa6437e14811198379b18cdfa7f8
"ARM: consolidate SMP cross call implementation" broke the ux500
compilation since the smp.h header declared a function called
from headsmp.S. This fixes it up by declaring it locally instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As a result of c42321c (genirq: Make generic irq chip depend on
CONFIG_GENERIC_IRQ_CHIP), we now need those platforms using this in
my tree to select this symbol.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a dtb is passed to the kernel then the kernel needs to iterate
through compiled-in mdescs looking for one that matches and move the
dtb data to a safe location before it gets accidentally overwritten by
the kernel.
This patch creates a new function, setup_machine_fdt() which is
analogous to the setup_machine_atags() created in the previous patch.
It does all the early setup needed to use a device tree machine
description.
v5: - Print warning with neither dtb nor atags are passed to the kernel
- Fix bug in setting of __machine_arch_type to the selected machine,
not just the last machine in the list.
Reported-by: Tixy <tixy@yxit.co.uk>
- Copy command line directly into boot_command_line instead of cmd_line
v4: - Dump some output when a matching machine_desc cannot be found
v3: - Added processing of reserved list.
- Backed out the v2 change that copied instead of reserved the
dtb. dtb is reserved again and the real problem was fixed by
using alloc_bootmem_align() for early allocation of RAM for
unflattening the tree.
- Moved cmd_line and initrd changes to earlier patch to make series
bisectable.
v2: Changed to save the dtb by copying into an allocated buffer.
- Since the dtb will very likely be passed in the first 16k of ram
where the interrupt vectors live, memblock_reserve() is
insufficient to protect the dtb data.
[based on work originally written by Jeremy Kerr <jeremy.kerr@canonical.com>]
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In preparation for adding device tree support, this patch consolidates
all of the atag-specific setup into a single function.
v5: - drop double printk("Machine; %s\n", ...); call.
- leave copying boot_command_line in setup_arch() since it isn't
atags specific.
v4: - adapt to the removal of lookup_machine_type()
- break out dump of machine_desc table into dump_machine_table()
because the device tree probe code will use it.
- Add for_each_machine_desc() macro
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The generic chip infrastructure has had a Kconfig symbol added so we need
to select that for the kernel to link now we're using the generic IRQ
chip infrastructure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When initialising a PMU, there is a check to protect against races with
other CPUs filling all of the available event slots. Since armpmu_add
checks that an event can be scheduled, we do not need to do this at
initialisation time. Furthermore the current code is broken because it
assumes that atomic_inc_not_zero will unconditionally increment
active_counts and then tries to decrement it again on failure.
This patch removes the broken, redundant code.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We only need one defconfig for SPEAr3xx now since we can build all
three boards into one kernel.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that all three SPEAr3xx platforms can be built into one kernel,
rework KConfig to allow this. Move everything into one KConfig file
while we are here.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prefix the pmx_devs to remove naming conflicts between the three
SPEAr3xx platforms. Also make pmx_driver static to each platform and
rework the init code to pass the devices rather than export the
pmx_driver structure.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prefix register and irq defintions to remove naming conflicts between
the three SPEAr3xx platforms.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several structures in arch/arm/mach-spear3xx are not marked static
like they should be. Fix this.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch creates different clk_lookup arrays for individual machines.
These lookup arrays will be registered only if that specific machine is
current machine.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define common clk_init routine in plat/clock.c for calling recalc_root_clocks.
This routine will be used for any common code across all machine families.
Whereas family specific spear*xx_clk_init routines will be used for family
specific code.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The set_vpp() method provided by physmap passes a map_info back to
the platform code, which has little relevance as far as the platform
is concerned (this parameter is completely unused).
Instead, pass the platform_device, which can be used in the pismo
driver to retrieve some important information in a nicer way, instead
of the hack that was in place.
The empty set_vpp function in board-at572d940hf_ek.c is left untouched,
as the board/SoC is scheduled for removal.
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested with an ARM-1136 core tile.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested on a PB11-MPCore.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It shows up on the console despite using "silent" in the bootargs, and
it's really just noise in the boot log since PM init is always called.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: jhnikula@gmail.com
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
The achievable power modes of the power domains in cpuidle
depends on the system wide 'enable_off_mode' knob in debugfs.
Upon changing enable_off_mode, do not change the C-states
'valid' field but instead dynamically restrict the power modes
when entering idle.
The C-states 'valid' field is just used to enable/disable some
C-states at init and shall not be changed later on.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
- fix single and multi-lines comments format
- removed the omap3_idle_bm_check function and replaced the test
in omap3_enter_idle_bm by the equivalent code
- re-organize omap3_enter_idle_bm code path, assign local variables
only when needed
- reword some comments
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current implementation defines an internal structure and a
C-states array. Using those structures is redundant to the
structs used by the cpuidle framework.
This patch provides a clean-up of the internal struct, removes the
internal C-states array, stores the data using the existing cpuidle
per C-state struct and registers the mach specific data to cpuidle
C-state driver_data (accessed using cpuidle_[gs]et_statedata).
Also removes unused macros, fields and code and compacts the repeating
code using an inline helper function.
The result is more compact and more readable code as well as
reduced data RAM usage.
Also retain C1 as the only always valid C-state and system safe state.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
- sleep_latency and wake_latency are not used, replace them by
exit_latency which is used by cpuidle. exit_latency simply is
the sum of sleep_latency and wake_latency,
- replace threshold by target_residency,
- changed the OMAP3 specific cpuidle code accordingly,
- changed the OMAP3 board code accordingly.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The cpuidle states settings can be overriden by some board-
specific settings, by calling omap3_pm_init_cpuidle.
Remove the 3430SDP specific states settings registration
since the figures are identical to the default ones (in cpuidle34xx.c).
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (44 commits)
debugfs: Silence DEBUG_STRICT_USER_COPY_CHECKS=y warning
sysfs: remove "last sysfs file:" line from the oops messages
drivers/base/memory.c: fix warning due to "memory hotplug: Speed up add/remove when blocks are larger than PAGES_PER_SECTION"
memory hotplug: Speed up add/remove when blocks are larger than PAGES_PER_SECTION
SYSFS: Fix erroneous comments for sysfs_update_group().
driver core: remove the driver-model structures from the documentation
driver core: Add the device driver-model structures to kerneldoc
Translated Documentation/email-clients.txt
RAW driver: Remove call to kobject_put().
reboot: disable usermodehelper to prevent fs access
efivars: prevent oops on unload when efi is not enabled
Allow setting of number of raw devices as a module parameter
Introduce CONFIG_GOOGLE_FIRMWARE
driver: Google Memory Console
driver: Google EFI SMI
x86: Better comments for get_bios_ebda()
x86: get_bios_ebda_length()
misc: fix ti-st build issues
params.c: Use new strtobool function to process boolean inputs
debugfs: move to new strtobool
...
Fix up trivial conflicts in fs/debugfs/file.c due to the same patch
being applied twice, and an unrelated cleanup nearby.
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: convert mips to generic i8253 clocksource
clocksource: convert x86 to generic i8253 clocksource
clocksource: convert footbridge to generic i8253 clocksource
clocksource: add common i8253 PIT clocksource
blackfin: convert to clocksource_register_hz
mips: convert to clocksource_register_hz/khz
sparc: convert to clocksource_register_hz/khz
alpha: convert to clocksource_register_hz
microblaze: convert to clocksource_register_hz/khz
ia64: convert to clocksource_register_hz/khz
x86: Convert remaining x86 clocksources to clocksource_register_hz/khz
Make clocksource name const
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
sched: Fix and optimise calculation of the weight-inverse
sched: Avoid going ahead if ->cpus_allowed is not changed
sched, rt: Update rq clock when unthrottling of an otherwise idle CPU
sched: Remove unused parameters from sched_fork() and wake_up_new_task()
sched: Shorten the construction of the span cpu mask of sched domain
sched: Wrap the 'cfs_rq->nr_spread_over' field with CONFIG_SCHED_DEBUG
sched: Remove unused 'this_best_prio arg' from balance_tasks()
sched: Remove noop in alloc_rt_sched_group()
sched: Get rid of lock_depth
sched: Remove obsolete comment from scheduler_tick()
sched: Fix sched_domain iterations vs. RCU
sched: Next buddy hint on sleep and preempt path
sched: Make set_*_buddy() work on non-task entities
sched: Remove need_migrate_task()
sched: Move the second half of ttwu() to the remote cpu
sched: Restructure ttwu() some more
sched: Rename ttwu_post_activation() to ttwu_do_wakeup()
sched: Remove rq argument from ttwu_stat()
sched: Remove rq->lock from the first half of ttwu()
sched: Drop rq->lock from sched_exec()
...
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix rt_rq runtime leakage bug
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (34 commits)
PM: Introduce generic prepare and complete callbacks for subsystems
PM: Allow drivers to allocate memory from .prepare() callbacks safely
PM: Remove CONFIG_PM_VERBOSE
Revert "PM / Hibernate: Reduce autotuned default image size"
PM / Hibernate: Add sysfs knob to control size of memory for drivers
PM / Wakeup: Remove useless synchronize_rcu() call
kmod: always provide usermodehelper_disable()
PM / ACPI: Remove acpi_sleep=s4_nonvs
PM / Wakeup: Fix build warning related to the "wakeup" sysfs file
PM: Print a warning if firmware is requested when tasks are frozen
PM / Runtime: Rework runtime PM handling during driver removal
Freezer: Use SMP barriers
PM / Suspend: Do not ignore error codes returned by suspend_enter()
PM: Fix build issue in clock_ops.c for CONFIG_PM_RUNTIME unset
PM: Revert "driver core: platform_bus: allow runtime override of dev_pm_ops"
OMAP1 / PM: Use generic clock manipulation routines for runtime PM
PM: Remove sysdev suspend, resume and shutdown operations
PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
...
Fixing a few "please, no space before tabs" and "empty line at end of
file" warnings on the way.
LAKML-Reference: 1299271882-2130-6-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
APF9328 is an i.MXL based SOM (System On Module) that can be plugged on
several docking/development boards. Here only basic module support
is added (Ethernet, Serial, NOR Flash).
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Nicolas Colombain <nicolas.colombain@armadeus.com>
Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 47babe69 (mxs: dynamically allocate mmc device) added the ssp
setup and mmc clocks for mx23/28, but forgot to register the mmc clocks
on mx23.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To be able to compile e.g. i.MX31 and i.MX51 in a single kernel image
the ioremap quirk needs a runtime check.
While touching this code make the comment more understandable by adding
a sentence from the commit log that introduced it
(eadefef ([ARM] MX3: Use ioremap wrapper to map SoC devices nonshared)).
As mach/io.h now uses cpu_is_ some header reshuffling in mach/hardware.h
was necessary. (mach/mx27.h and mach/mx31.h #include <linux/io.h> which
#includes <mach/io.h>. So mach/mxc.h which provides the cpu_is_ macros
needs to be included before mach/mx27.h and mach/mx31.h.)
LAKML-Reference: 1302464943-20721-5-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The two SoCs have different PHYS_OFFSETs so it's not (yet) possible to
compile a single (working) kernel for these.
LAKML-Reference: 1302464943-20721-4-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The symbols in this choice should only be used to select between the
available machines that can be built into a single kernel. As these sets
(will) differ e.g. depending on ARM_PATCH_PHYS_VIRT and AUTO_ZRELADDR
letting them select other symbols makes the logic more complex and needs
to duplicate some things. So let the machines select the corresponding
symbols (indirectly via SOC_XYZ).
LAKML-Reference: 1302464943-20721-2-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since support for mxc91231 was introduced 2009 it only saw patches that
were part of (mxc or arm) global cleanups. The only supported machine
only had 4 devices (2x UART, sdhc, watchdog).
Cc: Dmitriy Taychenachev <dimichxp@gmail.com>
LAKML-Reference: 1302211482-17926-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
remove usage of CONFIG_ARCH_MX1. It's mostly unused anyway, replace
it with cpu_is_mx1() where necessary. Also, depend on
IMX_HAVE_PLATFORM_IMX_FB instead of the architectures directly.
LAKML-Reference: 20110303141244.GQ29521@pengutronix.de
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There is no need for using a MX51-specific version of imx_add_gpio_keys.
Remove imx51_add_gpio_keys and use imx_add_gpio_keys instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1302105926-20574-1-git-send-email-fabio.estevam@freescale.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The platform id is used to determine the spi bus number, so it should
better be different to the ids used for imx51-ecspi. Otherwise it's not
possible to use both devices "imx51-cspi.0" and "imx51-ecspi.0".
Alternative approaches are to use dynamic bus numbering as offered by
the spi framework or let the machine code set the bus number. The
downside of both possibilities is that the bus number isn't fixed for
the same busses on different machines using i.MX51.
LAKML-Reference: 1302100716-21034-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For consistency mxs has to be repeated, one for the name space and
another one for the device name.
LAKML-Reference: 1300308028-8922-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The defines for the i2c related irqs (MX23_INT_I2C_DMA and
MX23_INT_I2C_ERROR) already match the reference manual. So make the base
address consistent.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
LAKML-Reference: 1298049507-6987-2-git-send-email-w.sang@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
... together with the related devices "mx3_camera" and "mx3_sdc_fb".
"mx3_camera" doesn't fit the scheme of the other devices that just are
allocated and registered in a single function because it needs additional
care to get some dmaable memory. So currently imx31_alloc_mx3_camera
duplicates most of imx_add_platform_device_dmamask, but I'm not sure it's
worth to split the latter to be able to reuse more code.
This gets rid of mach-mx3/devices.[ch] and so several files need to be
adapted not to #include devices.h anymore.
LAKML-Reference: 1299271882-2130-5-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It's not allowed to create an alias of system RAM for DMA. So the memory
used must not be allocated using dma_alloc_coherent but has to be reserved
before using memblock routines.
There is no need to memzero the buffer because dma_alloc_coherent zeros
the memory for us.
LAKML-Reference: 1299271882-2130-4-git-send-email-u.kleine-koenig@pengutronix.de
Tested-by: Philippe Retornaz <philippe.retornaz@epfl.ch>
Acked-by: Philippe Retornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There is no need to memzero the buffer because dma_alloc_coherent zeros
the memory for us.
This fixes:
BUG: Your driver calls ioremap() on system memory. This leads
<4>to architecturally unpredictable behaviour on ARMv6+, and ioremap()
<4>will fail in the next kernel release. Please fix your driver.
Tested-by: Michael Grzeschik <mgr@pengutronix.de>
LAKML-Reference: 1299271882-2130-3-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code does not set the GPIO value to zero as mentioned in the comment.
Fix it by setting the initial GPIO value to zero.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1301427910-31726-1-git-send-email-fabio.estevam@freescale.com
[ukleinek: squashed two patches together fixing both boards at once]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most machine files include "devices-imxXX.h" which in turn includes
<mach/devices-common.h>. The latter already includes many headers
that the machine files don't need to include again.
These were found by:
$ grep \#include arch/arm/plat-mxc/include/mach/devices-common.h > tmpfile
$ git grep -l 'devices-imx' arch/arm | xargs grep -f tmpfile -F
(but I kept linux/init.h, linux/kernel.h and linux/platform_device.h)
LAKML-Reference: 1298912674-15153-2-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code inside babbage_usbhub_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value to the same level right after. This is not needed.
By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1300377359-23212-2-git-send-email-fabio.estevam@freescale.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Having the silicon revision to appear on the boot log is a useful information.
MX31, MX35 and MX51 already show the silicon revision on boot.
Add support for displaying such information for MX53 as well.
Tested on a mx53loco board, where it shows:
CPU identified as i.MX53, silicon rev 2.0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1301068367-18937-1-git-send-email-fabio.estevam@freescale.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Powerdown the internal UTMI PHY when USB is not enabled. This will
allow the OMAP core domain to transition to retention and offmode.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
omap4430_phy_init() function can be called with no device pointer,
to powerdown the PHY during board init when USB is disabled.
Fix the function accordingly.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Powerdown the internal PHY during board init for OMAP44xx.
So that when musb is disabled core transition to retention/off
is not blocked.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* power-domains:
PM: Fix build issue in clock_ops.c for CONFIG_PM_RUNTIME unset
PM: Revert "driver core: platform_bus: allow runtime override of dev_pm_ops"
OMAP1 / PM: Use generic clock manipulation routines for runtime PM
PM / Runtime: Generic clock manipulation rountines for runtime PM (v6)
PM / Runtime: Add subsystem data field to struct dev_pm_info
OMAP2+ / PM: move runtime PM implementation to use device power domains
PM / Platform: Use generic runtime PM callbacks directly
shmobile: Use power domains for platform runtime PM
PM: Export platform bus type's default PM callbacks
PM: Make power domain callbacks take precedence over subsystem ones
* syscore:
PM: Remove sysdev suspend, resume and shutdown operations
PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
PM / Blackfin: Use struct syscore_ops instead of sysdevs for PM
ARM / Samsung: Use struct syscore_ops for "core" power management
ARM / PXA: Use struct syscore_ops for "core" power management
ARM / SA1100: Use struct syscore_ops for "core" power management
ARM / Integrator: Use struct syscore_ops for core PM
ARM / OMAP: Use struct syscore_ops for "core" power management
ARM: Use struct syscore_ops instead of sysdevs for PM in common code
Add IGEP3 machine support to board-igep0020
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
to allow easy addition of IGEP3
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP2 and IGEP3 boards are very similar and can be merged into one file.
Start refactoring with changing igep2 to igep where applicable.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mv78xx0 and kirkwood use identical mpp code.
It should also be possible to rewrite the orion5x mpp to use this
platform code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This change removes the interrupt resource. The driver does not use
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Changing eg 0xffffffff to DMA_BIT_MASK(32) etc allows easier
side by side comparision of identical code which can be consolidated.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The core interrupt chip is a straight forward conversion. The gpio
chip is implemented with two instances of the irq_chip_type which can
be switched with the irq_set_type function. That allows us to use the
generic callbacks and avoids the conditionals in them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Convert OMAP1 to using the new generic clock manipulation routines
and a device power domain for runtime PM instead of overriding the
platform bus type's runtime PM callbacks. This allows us to simplify
OMAP1-specific code and to share some code with other platforms
(shmobile in particular).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3: set the core dpll clk rate in its set_rate function
omap: iommu: Return IRQ_HANDLED in fault handler when no fault occured
when cache_is_vipt_nonaliasing(), we always have pte_exec() true at
the end of this function, so no need for the additional check.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current mainline codes of ARCH_S5PC100 cannot support
suspend to ram. So needs this for preventing build error.
Cc: Russell King <rmk+kernel at arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim at samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use generic irq chip for omap2 & 3.
Note that this patch also leaves out the spurious IRQ warning
for omap3.
This warning should no longer be needed as the interrupt handlers
for various devices have implemented the necessayr read-back of
the posted write.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch migrates the implementation of the ptrace interface for
the core integer registers, legacy FPA registers and VFP registers
to use the regsets framework.
As an added bonus, all this stuff gets included in coredumps
at no extra cost. Without this patch, coredumps contained no
VFP state.
Third-party extension register sets (iwmmx, crunch) are not migrated
by this patch, and continue to use the old implementation;
these should be migratable without much extra work.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the footbridge isa-timer code to use generic i8253 clocksource.
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On some arches (x86, sh, arm, unicore, powerpc) the oops message would
print out the last sysfs file accessed.
This was very useful in finding a number of sysfs and driver core bugs
in the 2.5 and early 2.6 development days, but it has been a number of
years since this file has actually helped in debugging anything that
couldn't also be trivially determined from the stack traceback.
So it's time to delete the line. This is good as we need all the space
we can get for oops messages at times on consoles.
Acked-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The debug l3_ick/rate is not displaying the actual rate of the clock in
hardware. This is because, the core dpll set_rate function doesn't update the
clk.rate. After fixing, the l3_ick/rate is displaying proper values.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Wamsley <paul@pwsan.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board support has never been merged for it as noticed
by Russell King <linux@arm.linux.org.uk>. So let's remove the
related dead code.
Cc: linux-fbdev@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6870/1: The mandatory barrier rmb() must be a dsb() in for device accesses
ARM: 6892/1: handle ptrace requests to change PC during interrupted system calls
ARM: 6890/1: memmap: only free allocated memmap entries when using SPARSEMEM
ARM: zImage: the page table memory must be considered before relocation
ARM: zImage: make sure not to relocate on top of the relocation code
ARM: zImage: Fix bad SP address after relocating kernel
ARM: zImage: make sure the stack is 64-bit aligned
ARM: RiscPC: acornfb: fix section mismatches
ARM: RiscPC: etherh: fix section mismatches
use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since mandatory barriers may be used (explicitly or implicitly via readl
etc.) to ensure the ordering between Device and Normal memory accesses,
a DMB is not enough. This patch converts it to a DSB.
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GDB's interrupt.exp test cases currenly fail on ARM. The problem is how do_signal
handled restarting interrupted system calls:
The entry.S assembler code determines that we come from a system call; and that
information is passed as "syscall" parameter to do_signal. That routine then
calls get_signal_to_deliver [*] and if a signal is to be delivered, calls into
handle_signal. If a system call is to be restarted either after the signal
handler returns, or if no handler is to be called in the first place, the PC
is updated after the get_signal_to_deliver call, either in handle_signal (if
we have a handler) or at the end of do_signal (otherwise).
Now the problem is that during [*], the call to get_signal_to_deliver, a ptrace
intercept may happen. During this intercept, the debugger may change registers,
including the PC. This is done by GDB if it wants to execute an "inferior call",
i.e. the execution of some code in the debugged program triggered by GDB.
To this purpose, GDB will save all registers, allocate a stack frame, set up
PC and arguments as appropriate for the call, and point the link register to
a dummy breakpoint instruction. Once the process is restarted, it will execute
the call and then trap back to the debugger, at which point GDB will restore
all registers and continue original execution.
This generally works fine. However, now consider what happens when GDB attempts
to do exactly that while the process was interrupted during execution of a to-be-
restarted system call: do_signal is called with the syscall flag set; it calls
get_signal_to_deliver, at which point the debugger takes over and changes the PC
to point to a completely different place. Now get_signal_to_deliver returns
without a signal to deliver; but now do_signal decides it should be restarting
a system call, and decrements the PC by 2 or 4 -- so it now points to 2 or 4
bytes before the function GDB wants to call -- which leads to a subsequent crash.
To fix this problem, two things need to be supported:
- do_signal must be able to recognize that get_signal_to_deliver changed the PC
to a different location, and skip the restart-syscall sequence
- once the debugger has restored all registers at the end of the inferior call
sequence, do_signal must recognize that *now* it needs to restart the pending
system call, even though it was now entered from a breakpoint instead of an
actual svc instruction
This set of issues is solved on other platforms, usually by one of two
mechanisms:
- The status information "do_signal is handling a system call that may need
restarting" is itself carried in some register that can be accessed via
ptrace. This is e.g. on Intel the "orig_eax" register; on Sparc the kernel
defines a magic extra bit in the flags register for this purpose.
This allows GDB to manage that state: reset it when doing an inferior call,
and restore it after the call is finished.
- On s390, do_signal transparently handles this problem without requiring
GDB interaction, by performing system call restarting in the following
way: first, adjust the PC as necessary for restarting the call. Then,
call get_signal_to_deliver; and finally just continue execution at the
PC. This way, if GDB does not change the PC, everything is as before.
If GDB *does* change the PC, execution will simply continue there --
and once GDB restores the PC it saved at that point, it will automatically
point to the *restarted* system call. (There is the minor twist how to
handle system calls that do *not* need restarting -- do_signal will undo
the PC change in this case, after get_signal_to_deliver has returned, and
only if ptrace did not change the PC during that call.)
Because there does not appear to be any obvious register to carry the
syscall-restart information on ARM, we'd either have to introduce a new
artificial ptrace register just for that purpose, or else handle the issue
transparently like on s390. The patch below implements the second option;
using this patch makes the interrupt.exp test cases pass on ARM, with no
regression in the GDB test suite otherwise.
Cc: patches@linaro.org
Signed-off-by: Ulrich Weigand <ulrich.weigand@linaro.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SPARSEMEM code allocates memmap entries only for sections which are
present (i.e. those which contain some valid memory). The membank checks
in free_unused_memmap do not take this into account and can incorrectly
attempt to free memory which is not allocated, resulting in a BUG() in
the bootmem code.
However, if memory is configured as follows:
|<----section---->|<----hole---->|<----section---->|
+--------+--------+--------------+--------+--------+
| bank 0 | unused | | bank 1 | unused |
+--------+--------+--------------+--------+--------+
where a bank only occupies part of a section, the memmap allocated for
the remainder of the section *can* be freed.
This patch modifies the checks in free_unused_memmap so that only valid
memmap entries are considered for removal.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch allows the provided CONFIG_CMDLINE to be concatenated
with the one provided by the boot loader. This is useful to
merge the static values defined in CONFIG_CMDLINE with the
boot loader's (possibly) more dynamic values, such as startup
reasons and more.
Signed-off-by: Victor Boivie <victor.boivie@sonyericsson.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonyericsson.com>
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch uses the load/store exclusive instructions to add SMP futex
support for ARM.
Since the ARM architecture does not provide instructions for
unprivileged exclusive memory accesses, we can only provide SMP futexes
when CPU domain support is disabled.
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM kernel supports writethrough data cache via the
CONFIG_CPU_DCACHE_WRITETHROUGH option. However, that
functionality wasn't implemented in the arch/arm/boot/compressed
code. It is now necessary due to a new ARM926EJS processor
that has an issue with writeback data cache.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Highmem on ARM has been around for a while now, without any major issues
being raised. So, drop the experimental status of this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SMP on ARM has been around for a while now, without any major issues
being raised. So, drop the experimental status of this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than each platform providing its own function to adjust the
zone sizes, use the new ARM_DMA_ZONE_SIZE definition to perform this
adjustment. This ensures that the actual DMA zone size and the
ISA_DMA_THRESHOLD/MAX_DMA_ADDRESS definitions are consistent with
each other, and moves this complexity out of the platform code.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The values of ISA_DMA_THRESHOLD and MAX_DMA_ADDRESS are related; one is
the physical/bus address, the other is the virtual address. Both need
to be kept in step, so rather than having platforms define both, allow
them to define a single macro which sets both of these macros
appropraitely.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tegra hardware design cannot reliably support an arbitrary set of keys
waking up the system. Modify wakeup logic so either any key wakes the
system up or none will do.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit d594f1f31a (omap: IOMMU: add
support to callback during fault handling) broke interrupt line sharing
between the OMAP3 ISP and its IOMMU. Because of this, every interrupt
generated by the OMAP3 ISP is handled by the IOMMU driver instead of
being passed to the OMAP3 ISP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Simple conversion which simply uses the fact that the second irq chip
base address has offset 0x04 to the first one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-and-Tested-by: Kevin Hilman <khilman@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
The GIC register accesses today make use of readl()/writel()
which prove to be very expensive when used along with mandatory
barriers. This mandatory barriers also introduces an un-necessary
and expensive l2x0_sync() operation. On Cortex-A9 MP cores, GIC
IO accesses from CPU are direct and doesn't go through L2X0 write
buffer.
A DSB before writel_relaxed() in gic_raise_softirq() is added to be
compliant with the Barrier Litmus document - the mailbox scenario.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Currently, the gic uses handle_level_irq for handling SPIs (Shared
Peripheral Interrupts), requiring active interrupts to be masked at
the distributor level during IRQ handling.
On a virtualised system, only the CPU interfaces are virtualised in
hardware. Accesses to the distributor must be trapped by the
hypervisor, adding latency to the critical interrupt path in Linux.
This patch modifies the GIC code to use handle_fasteoi_irq for handling
interrupts, which only requires us to signal EOI to the CPU interface
when handling is complete. Cascaded IRQ handling is also updated to use
the chained IRQ enter/exit functions to honour the flow control of the
parent chip.
Note that commit 846afbd1 ("GIC: Dont disable INT in ack callback")
broke cascading interrupts by forgetting to add IRQ masking. This is
no longer an issue because the unmask call is now unnecessary.
Tested on Versatile Express and Realview EB (1176 w/ cascaded GICs).
Tested-and-reviewed-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Tested-and-acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that irq.c is just an interface layer between the gic
and legacy_irq.c, move the contents of legacy_irq.c into
irq.c.
Signed-off-by: Colin Cross <ccross@android.com>
Tegra PM irq support is being improved, remove it for now
until the rest of the platform gets PM support.
Signed-off-by: Colin Cross <ccross@android.com>
Replace the ugly hack that inserts legacy irq controller calls
into the irq call paths by reading and replacing the gic irq
chip with the new gic arch extensions.
Signed-off-by: Colin Cross <ccross@android.com>
This patch updates the Tegra gpio chained IRQ handler to use the chained
IRQ enter/exit functions in order to function correctly on primary
controllers with different methods of flow control.
This is required for the GIC to move to fasteoi interrupt handling.
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch updates the Nomadik gpio chained IRQ handler to use the
chained IRQ enter/exit functions in order to function correctly on
primary controllers with different methods of flow control.
Cc: Rabin Vincent <rabin@rab.in>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch updates the MSM gpio chained IRQ handler to use the chained
IRQ enter/exit functions in order to function correctly on primary
controllers with different methods of flow control.
Tested-and-reviewed-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch updates the IRQ combiner chained IRQ handler code to use the
chained IRQ enter/exit functions in order to function correctly on
primary controllers with different methods of flow control.
This is required for the GIC to move to fasteoi interrupt handling.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch updates the OMAP gpio chained IRQ handler to use the chained
IRQ enter/exit functions in order to function correctly on primary
controllers with different methods of flow control.
Cc: Colin Cross <ccross@google.com>
Cc: Tony Lindgren <tony@atomide.com>
Tested-and-acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add some basic empty infrastructure for DT support on ARM.
v5: - Fix off-by-one error in size calculation of initrd
- Stop mucking with cmd_line, and load command line from dt into
boot_command_line instead which matches the behaviour of ATAGS booting
v3: - moved cmd_line export and initrd setup to this patch to make the
series bisectable.
- switched to alloc_bootmem_align() for allocation when
unflattening the device tree. memblock_alloc() was not the
right interface.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The dtb is passed to the kernel via register r2, which is the same
method that is used to pass an atags pointer. This patch modifies
__vet_atags to not clear r2 when it encounters a dtb image.
v2: fixed bugs pointed out by Nicolas Pitre
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The interrupt printing functionality in the ep93xx gpio debugfs function
does not behave as expected. It prints [interrupt] beside all pins which
are capable of being interrupts, not just those which are currently
configured as interrupts.
The best solution is just to remove the custom ep93xx gpio debugfs
function all together. The generic gpiolib one is good enough.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, omap_display_init() maintains arrays for hwmod name(oh_name) and the
correspnding platform_device name(dev_name) needed by omap_device_build().
A variable oh_count keeps a track of the number of devices to build from oh_name
based on what omap revision it is.
Clean this up by maintaining an array of omap_dss_hwmod_data struct which is
defined for each omap revision as suggested by Tomi Valkeinen. Assign the
corresponding omap_dss_hwmod_data array struct to the pointer curr_dss_hwmod in
omap_display_init().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move some of the configurable HDMI PLL parameters to dssdev.clock struct.
Cleanup the function hdmi_compute_pll() by using the parameters defined in the
board file and do some cosmetic modifications.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/nokia-dsi-panel.h is an include for the
OMAP DSS panel driver for Nokia's DSI displays. A more logical place for
it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/panel-generic-dpi.h is an include for
the OMAP DSS panel driver for generic DPI displays. A more logical place
for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for USB 2.0 High-Speed gadget controller driver for Samsung's
S3C2416 processor.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
S3C2416, S3C2443 and S3C2450 includes a USB High-Speed Gadget controller module.
This patch adds the following for supporting this controller.
1. Definition for USB High-Speed controller base address.
2. Platform device instantiation.
3. Declaration for platform data structure.
4. Functionality to setup platform data for the controller.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add register definitions required to configure the USB Phy. The definitions
for PHYCTRL, PHYPWR, URSTCON and UCLKCON registers and corresponding bit
field definitions are added.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most boards use exactly the same configuration for musb initialization.
Create a default that can be shared amount different boards.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols. This usually means that no global variables can
be marked static unless they're also const.
To enforce this, suffice to fail the build whenever a private symbol
is allocated to .bss and list those symbols for convenience.
The user_stack and user_stack_end labels in head.S were converted into
non exported symbols to remove false positives.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
To be able to relocate the .bss section at run time independently from
the rest of the code, we must make sure that no GOTOFF relocations are
used with .bss symbols. This usually means that no global variables can
be marked static unless they're also const.
Let's remove the static qualifier from current offenders, or turn them
into const variables when possible. Next commit will ensure the build
fails if one of those is reintroduced due to otherwise enforced coding
standards for the kernel.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
If decompress() returns an error without calling error(), we must
not attempt to boot the resulting kernel.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Magnus Damm